include/configs/T104xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  * Copyright 2020 NXP
   5  */
   6
   7 #ifndef __CONFIG_H
   8 #define __CONFIG_H
   9
  10 #include <linux/stringify.h>
  11
  12 /*
  13  * T104x RDB board configuration file
  14  */
  15 #include <asm/config_mpc85xx.h>
  16
  17 #ifdef CONFIG_RAMBOOT_PBL
  18 #define CONFIG_SPL_FLUSH_IMAGE
  19 #define CONFIG_SPL_PAD_TO               0x40000
  20 #define CONFIG_SPL_MAX_SIZE             0x28000
  21 #ifdef CONFIG_SPL_BUILD
  22 #define CONFIG_SPL_SKIP_RELOCATE
  23 #define CONFIG_SPL_COMMON_INIT_DDR
  24 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  25 #endif
  26 #define RESET_VECTOR_OFFSET             0x27FFC
  27 #define BOOT_PAGE_OFFSET                0x27000
  28
  29 #ifdef CONFIG_MTD_RAW_NAND
  30 #ifdef CONFIG_NXP_ESBC
  31 #define CONFIG_U_BOOT_HDR_SIZE          (16 << 10)
  32 /*
  33  * HDR would be appended at end of image and copied to DDR along
  34  * with U-Boot image.
  35  */
  36 #define CONFIG_SYS_NAND_U_BOOT_SIZE     ((768 << 10) + \
  37                                          CONFIG_U_BOOT_HDR_SIZE)
  38 #else
  39 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  40 #endif
  41 #define CONFIG_SYS_NAND_U_BOOT_DST      0x30000000
  42 #define CONFIG_SYS_NAND_U_BOOT_START    0x30000000
  43 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  44 #endif
  45
  46 #ifdef CONFIG_SPIFLASH
  47 #define CONFIG_RESET_VECTOR_ADDRESS             0x30000FFC
  48 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  49 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE        (768 << 10)
  50 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST         (0x30000000)
  51 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START       (0x30000000)
  52 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS        (256 << 10)
  53 #ifndef CONFIG_SPL_BUILD
  54 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  55 #endif
  56 #endif
  57
  58 #ifdef CONFIG_SDCARD
  59 #define CONFIG_RESET_VECTOR_ADDRESS             0x30000FFC
  60 #define CONFIG_SYS_MMC_U_BOOT_SIZE      (768 << 10)
  61 #define CONFIG_SYS_MMC_U_BOOT_DST       (0x30000000)
  62 #define CONFIG_SYS_MMC_U_BOOT_START     (0x30000000)
  63 #define CONFIG_SYS_MMC_U_BOOT_OFFS      (260 << 10)
  64 #ifndef CONFIG_SPL_BUILD
  65 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  66 #endif
  67 #endif
  68
  69 #endif
  70
  71 /* High Level Configuration Options */
  72 #define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
  73
  74 /* support deep sleep */
  75 #define CONFIG_DEEP_SLEEP
  76
  77 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  78 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  79 #endif
  80
  81 #define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
  82 #define CONFIG_SYS_NUM_CPC              CONFIG_SYS_NUM_DDR_CTLRS
  83 #define CONFIG_PCIE1                    /* PCIE controller 1 */
  84 #define CONFIG_PCIE2                    /* PCIE controller 2 */
  85 #define CONFIG_PCIE3                    /* PCIE controller 3 */
  86 #define CONFIG_PCIE4                    /* PCIE controller 4 */
  87
  88 #define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */
  89
  90 #if defined(CONFIG_SPIFLASH)
  91 #elif defined(CONFIG_MTD_RAW_NAND)
  92 #ifdef CONFIG_NXP_ESBC
  93 #define CONFIG_RAMBOOT_NAND
  94 #define CONFIG_BOOTSCRIPT_COPY_RAM
  95 #endif
  96 #endif
  97
  98 #define CONFIG_SYS_CLK_FREQ     100000000
  99
 100 /*
 101  * These can be toggled for performance analysis, otherwise use default.
 102  */
 103 #define CONFIG_SYS_CACHE_STASHING
 104 #define CONFIG_BACKSIDE_L2_CACHE
 105 #define CONFIG_SYS_INIT_L2CSR0          L2CSR0_L2E
 106 #define CONFIG_BTB                      /* toggle branch predition */
 107 #ifdef CONFIG_DDR_ECC
 108 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 109 #endif
 110
 111 #define CONFIG_ENABLE_36BIT_PHYS
 112
 113 /*
 114  *  Config the L3 Cache as L3 SRAM
 115  */
 116 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 117 /*
 118  * For Secure Boot CONFIG_SYS_INIT_L3_ADDR will be redefined and hence
 119  * Physical address (CONFIG_SYS_INIT_L3_ADDR) and virtual address
 120  * (CONFIG_SYS_INIT_L3_VADDR) will be different.
 121  */
 122 #define CONFIG_SYS_INIT_L3_VADDR        0xFFFC0000
 123 #define CONFIG_SYS_L3_SIZE              256 << 10
 124 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_VADDR + 32 * 1024)
 125 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
 126 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 127 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (30 << 10)
 128 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 129
 130 #define CONFIG_SYS_DCSRBAR              0xf0000000
 131 #define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
 132
 133 /*
 134  * DDR Setup
 135  */
 136 #define CONFIG_VERY_BIG_RAM
 137 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 138 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 139
 140 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 141 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 142
 143 #define CONFIG_SYS_SPD_BUS_NUM  0
 144 #define SPD_EEPROM_ADDRESS      0x51
 145
 146 #define CONFIG_SYS_SDRAM_SIZE   4096    /* for fixed parameter use */
 147
 148 /*
 149  * IFC Definitions
 150  */
 151 #define CONFIG_SYS_FLASH_BASE   0xe8000000
 152 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 153
 154 #define CONFIG_SYS_NOR_CSPR_EXT (0xf)
 155 #define CONFIG_SYS_NOR_CSPR     (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \
 156                                 CSPR_PORT_SIZE_16 | \
 157                                 CSPR_MSEL_NOR | \
 158                                 CSPR_V)
 159 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 160
 161 /*
 162  * TDM Definition
 163  */
 164 #define T1040_TDM_QUIRK_CCSR_BASE       0xfe000000
 165
 166 /* NOR Flash Timing Params */
 167 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 168 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 169                                 FTIM0_NOR_TEADC(0x5) | \
 170                                 FTIM0_NOR_TEAHC(0x5))
 171 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 172                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 173                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 174 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 175                                 FTIM2_NOR_TCH(0x4) | \
 176                                 FTIM2_NOR_TWPH(0x0E) | \
 177                                 FTIM2_NOR_TWP(0x1c))
 178 #define CONFIG_SYS_NOR_FTIM3    0x0
 179
 180 #define CONFIG_SYS_FLASH_QUIET_TEST
 181 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 182
 183 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* number of banks */
 184 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 185 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 186 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 187
 188 #define CONFIG_SYS_FLASH_EMPTY_INFO
 189 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
 190
 191 /* CPLD on IFC */
 192 #define CPLD_LBMAP_MASK                 0x3F
 193 #define CPLD_BANK_SEL_MASK              0x07
 194 #define CPLD_BANK_OVERRIDE              0x40
 195 #define CPLD_LBMAP_ALTBANK              0x44 /* BANK OR | BANK 4 */
 196 #define CPLD_LBMAP_DFLTBANK             0x40 /* BANK OR | BANK0 */
 197 #define CPLD_LBMAP_RESET                0xFF
 198 #define CPLD_LBMAP_SHIFT                0x03
 199
 200 #if defined(CONFIG_TARGET_T1042RDB_PI)
 201 #define CPLD_DIU_SEL_DFP                0x80
 202 #elif defined(CONFIG_TARGET_T1042D4RDB)
 203 #define CPLD_DIU_SEL_DFP                0xc0
 204 #endif
 205
 206 #if defined(CONFIG_TARGET_T1040D4RDB)
 207 #define CPLD_INT_MASK_ALL               0xFF
 208 #define CPLD_INT_MASK_THERM             0x80
 209 #define CPLD_INT_MASK_DVI_DFP           0x40
 210 #define CPLD_INT_MASK_QSGMII1           0x20
 211 #define CPLD_INT_MASK_QSGMII2           0x10
 212 #define CPLD_INT_MASK_SGMI1             0x08
 213 #define CPLD_INT_MASK_SGMI2             0x04
 214 #define CPLD_INT_MASK_TDMR1             0x02
 215 #define CPLD_INT_MASK_TDMR2             0x01
 216 #endif
 217
 218 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 219 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 220 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 221 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
 222                                 | CSPR_PORT_SIZE_8 \
 223                                 | CSPR_MSEL_GPCM \
 224                                 | CSPR_V)
 225 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 226 #define CONFIG_SYS_CSOR2        0x0
 227 /* CPLD Timing parameters for IFC CS2 */
 228 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 229                                         FTIM0_GPCM_TEADC(0x0e) | \
 230                                         FTIM0_GPCM_TEAHC(0x0e))
 231 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 232                                         FTIM1_GPCM_TRAD(0x1f))
 233 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 234                                         FTIM2_GPCM_TCH(0x8) | \
 235                                         FTIM2_GPCM_TWP(0x1f))
 236 #define CONFIG_SYS_CS2_FTIM3            0x0
 237
 238 /* NAND Flash on IFC */
 239 #define CONFIG_NAND_FSL_IFC
 240 #define CONFIG_SYS_NAND_BASE            0xff800000
 241 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 242
 243 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 244 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 245                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 246                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 247                                 | CSPR_V)
 248 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 249
 250 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 251                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 252                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 253                                 | CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
 254                                 | CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
 255                                 | CSOR_NAND_SPRZ_224/* Spare size = 224 */ \
 256                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 257
 258 #define CONFIG_SYS_NAND_ONFI_DETECTION
 259
 260 /* ONFI NAND Flash mode0 Timing Params */
 261 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 262                                         FTIM0_NAND_TWP(0x18)   | \
 263                                         FTIM0_NAND_TWCHT(0x07) | \
 264                                         FTIM0_NAND_TWH(0x0a))
 265 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 266                                         FTIM1_NAND_TWBE(0x39)  | \
 267                                         FTIM1_NAND_TRR(0x0e)   | \
 268                                         FTIM1_NAND_TRP(0x18))
 269 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f) | \
 270                                         FTIM2_NAND_TREH(0x0a) | \
 271                                         FTIM2_NAND_TWHRE(0x1e))
 272 #define CONFIG_SYS_NAND_FTIM3           0x0
 273
 274 #define CONFIG_SYS_NAND_DDR_LAW         11
 275 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 276 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 277
 278 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 279
 280 #if defined(CONFIG_MTD_RAW_NAND)
 281 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 282 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 283 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 284 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 285 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 286 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 287 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 288 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 289 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR_CSPR_EXT
 290 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR_CSPR
 291 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 292 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 293 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 294 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 295 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 296 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 297 #else
 298 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR_CSPR_EXT
 299 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR_CSPR
 300 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 301 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 302 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 303 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 304 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 305 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 306 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 307 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 308 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 309 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 310 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 311 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 312 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 313 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 314 #endif
 315
 316 #ifdef CONFIG_SPL_BUILD
 317 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 318 #else
 319 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 320 #endif
 321
 322 #if defined(CONFIG_RAMBOOT_PBL)
 323 #define CONFIG_SYS_RAMBOOT
 324 #endif
 325
 326 #ifdef CONFIG_SYS_FSL_ERRATUM_A008044
 327 #if defined(CONFIG_MTD_RAW_NAND)
 328 #define CONFIG_A008044_WORKAROUND
 329 #endif
 330 #endif
 331
 332 #define CONFIG_HWCONFIG
 333
 334 /* define to use L1 as initial stack */
 335 #define CONFIG_L1_INIT_RAM
 336 #define CONFIG_SYS_INIT_RAM_LOCK
 337 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000      /* Initial L1 address */
 338 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 339 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 340 /* The assembler doesn't like typecast */
 341 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 342         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 343           CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 344 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 345
 346 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 347                                         GENERATED_GBL_DATA_SIZE)
 348 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 349
 350 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 351
 352 /* Serial Port - controlled on board with jumper J8
 353  * open - index 2
 354  * shorted - index 1
 355  */
 356 #define CONFIG_SYS_NS16550_SERIAL
 357 #define CONFIG_SYS_NS16550_REG_SIZE     1
 358 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 359
 360 #define CONFIG_SYS_BAUDRATE_TABLE       \
 361         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 362
 363 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 364 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 365 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 366 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 367
 368 #if defined(CONFIG_TARGET_T1042RDB_PI) || defined(CONFIG_TARGET_T1042D4RDB)
 369 /* Video */
 370 #define CONFIG_FSL_DIU_FB
 371
 372 #ifdef CONFIG_FSL_DIU_FB
 373 #define CONFIG_FSL_DIU_CH7301
 374 #define CONFIG_SYS_DIU_ADDR     (CONFIG_SYS_CCSRBAR + 0x180000)
 375 #define CONFIG_VIDEO_LOGO
 376 #define CONFIG_VIDEO_BMP_LOGO
 377 #endif
 378 #endif
 379
 380 /* I2C */
 381
 382 /* I2C bus multiplexer */
 383 #define I2C_MUX_PCA_ADDR                0x70
 384 #define I2C_MUX_CH_DEFAULT      0x8
 385
 386 #if defined(CONFIG_TARGET_T1042RDB_PI)  || \
 387         defined(CONFIG_TARGET_T1040D4RDB)       || \
 388         defined(CONFIG_TARGET_T1042D4RDB)
 389 /* LDI/DVI Encoder for display */
 390 #define CONFIG_SYS_I2C_LDI_ADDR         0x38
 391 #define CONFIG_SYS_I2C_DVI_ADDR         0x75
 392 #define CONFIG_SYS_I2C_DVI_BUS_NUM      0
 393
 394 /*
 395  * RTC configuration
 396  */
 397 #define RTC
 398 #define CONFIG_RTC_DS1337               1
 399 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 400
 401 /*DVI encoder*/
 402 #define CONFIG_HDMI_ENCODER_I2C_ADDR  0x75
 403 #endif
 404
 405 /*
 406  * eSPI - Enhanced SPI
 407  */
 408
 409 /*
 410  * General PCI
 411  * Memory space is mapped 1-1, but I/O space must start from 0.
 412  */
 413
 414 #ifdef CONFIG_PCI
 415 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 416 #ifdef CONFIG_PCIE1
 417 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 418 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 419 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 420 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 421 #endif
 422
 423 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 424 #ifdef CONFIG_PCIE2
 425 #define CONFIG_SYS_PCIE2_MEM_VIRT       0x90000000
 426 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc10000000ull
 427 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 428 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 429 #endif
 430
 431 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 432 #ifdef CONFIG_PCIE3
 433 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xa0000000
 434 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc20000000ull
 435 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 436 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 437 #endif
 438
 439 /* controller 4, Base address 203000 */
 440 #ifdef CONFIG_PCIE4
 441 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xb0000000
 442 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc30000000ull
 443 #define CONFIG_SYS_PCIE4_IO_VIRT        0xf8030000
 444 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 445 #endif
 446
 447 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 448 #endif  /* CONFIG_PCI */
 449
 450 /* SATA */
 451 #define CONFIG_FSL_SATA_V2
 452 #ifdef CONFIG_FSL_SATA_V2
 453 #define CONFIG_SYS_SATA_MAX_DEVICE      1
 454 #define CONFIG_SATA1
 455 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 456 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 457
 458 #define CONFIG_LBA48
 459 #endif
 460
 461 /*
 462 * USB
 463 */
 464 #define CONFIG_HAS_FSL_DR_USB
 465
 466 #ifdef CONFIG_HAS_FSL_DR_USB
 467 #ifdef CONFIG_USB_EHCI_HCD
 468 #define CONFIG_USB_EHCI_FSL
 469 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 470 #endif
 471 #endif
 472
 473 #ifdef CONFIG_MMC
 474 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 475 #endif
 476
 477 /* Qman/Bman */
 478 #ifndef CONFIG_NOBQFMAN
 479 #define CONFIG_SYS_BMAN_NUM_PORTALS     10
 480 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 481 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 482 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 483 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 484 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 485 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 486 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 487 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 488                                         CONFIG_SYS_BMAN_CENA_SIZE)
 489 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 490 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 491 #define CONFIG_SYS_QMAN_NUM_PORTALS     10
 492 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 493 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 494 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 495 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 496 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 497 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 498 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 499 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 500                                         CONFIG_SYS_QMAN_CENA_SIZE)
 501 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 502 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 503
 504 #define CONFIG_SYS_DPAA_FMAN
 505 #define CONFIG_SYS_DPAA_PME
 506
 507 #define CONFIG_U_QE
 508
 509 /* Default address of microcode for the Linux Fman driver */
 510 #if defined(CONFIG_SPIFLASH)
 511 /*
 512  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 513  * env, so we got 0x110000.
 514  */
 515 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000
 516 #elif defined(CONFIG_SDCARD)
 517 /*
 518  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 519  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 520  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 521  */
 522 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
 523 #elif defined(CONFIG_MTD_RAW_NAND)
 524 #define CONFIG_SYS_FMAN_FW_ADDR (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
 525 #else
 526 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 527 #endif
 528
 529 #if defined(CONFIG_SPIFLASH)
 530 #define CONFIG_SYS_QE_FW_ADDR           0x130000
 531 #elif defined(CONFIG_SDCARD)
 532 #define CONFIG_SYS_QE_FW_ADDR           (512 * 0x920)
 533 #elif defined(CONFIG_MTD_RAW_NAND)
 534 #define CONFIG_SYS_QE_FW_ADDR           (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
 535 #else
 536 #define CONFIG_SYS_QE_FW_ADDR           0xEFF10000
 537 #endif
 538
 539 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 540 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 541 #endif /* CONFIG_NOBQFMAN */
 542
 543 #ifdef CONFIG_FMAN_ENET
 544 #if defined(CONFIG_TARGET_T1040RDB) || defined(CONFIG_TARGET_T1042RDB)
 545 #define CONFIG_SYS_SGMII1_PHY_ADDR             0x03
 546 #elif defined(CONFIG_TARGET_T1040D4RDB)
 547 #define CONFIG_SYS_SGMII1_PHY_ADDR             0x01
 548 #elif defined(CONFIG_TARGET_T1042D4RDB)
 549 #define CONFIG_SYS_SGMII1_PHY_ADDR             0x02
 550 #define CONFIG_SYS_SGMII2_PHY_ADDR             0x03
 551 #define CONFIG_SYS_SGMII3_PHY_ADDR             0x01
 552 #endif
 553
 554 #if defined(CONFIG_TARGET_T1040D4RDB) || defined(CONFIG_TARGET_T1042D4RDB)
 555 #define CONFIG_SYS_RGMII1_PHY_ADDR             0x04
 556 #define CONFIG_SYS_RGMII2_PHY_ADDR             0x05
 557 #else
 558 #define CONFIG_SYS_RGMII1_PHY_ADDR             0x01
 559 #define CONFIG_SYS_RGMII2_PHY_ADDR             0x02
 560 #endif
 561
 562 /* Enable VSC9953 L2 Switch driver on T1040 SoC */
 563 #if defined(CONFIG_TARGET_T1040RDB) || defined(CONFIG_TARGET_T1040D4RDB)
 564 #define CONFIG_VSC9953
 565 #ifdef CONFIG_TARGET_T1040RDB
 566 #define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR        0x04
 567 #define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR        0x08
 568 #else
 569 #define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR        0x08
 570 #define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR        0x0c
 571 #endif
 572 #endif
 573
 574 #define CONFIG_ETHPRIME         "FM1@DTSEC4"
 575 #endif
 576
 577 /*
 578  * Environment
 579  */
 580 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 581 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 582
 583 /*
 584  * Miscellaneous configurable options
 585  */
 586
 587 /*
 588  * For booting Linux, the board info and command line data
 589  * have to be in the first 64 MB of memory, since this is
 590  * the maximum mapped by the Linux kernel during initialization.
 591  */
 592 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 593 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 594
 595 #ifdef CONFIG_CMD_KGDB
 596 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 597 #endif
 598
 599 /*
 600  * Dynamic MTD Partition support with mtdparts
 601  */
 602
 603 /*
 604  * Environment Configuration
 605  */
 606 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 607 #define CONFIG_BOOTFILE         "uImage"
 608 #define CONFIG_UBOOTPATH        "u-boot.bin"    /* U-Boot image on TFTP server*/
 609
 610 #define __USB_PHY_TYPE  utmi
 611 #define RAMDISKFILE     "t104xrdb/ramdisk.uboot"
 612
 613 #ifdef CONFIG_TARGET_T1040RDB
 614 #define FDTFILE         "t1040rdb/t1040rdb.dtb"
 615 #elif defined(CONFIG_TARGET_T1042RDB_PI)
 616 #define FDTFILE         "t1042rdb_pi/t1042rdb_pi.dtb"
 617 #elif defined(CONFIG_TARGET_T1042RDB)
 618 #define FDTFILE         "t1042rdb/t1042rdb.dtb"
 619 #elif defined(CONFIG_TARGET_T1040D4RDB)
 620 #define FDTFILE         "t1042rdb/t1040d4rdb.dtb"
 621 #elif defined(CONFIG_TARGET_T1042D4RDB)
 622 #define FDTFILE         "t1042rdb/t1042d4rdb.dtb"
 623 #endif
 624
 625 #ifdef CONFIG_FSL_DIU_FB
 626 #define DIU_ENVIRONMENT "video-mode=fslfb:1024x768-32@60,monitor=dvi"
 627 #else
 628 #define DIU_ENVIRONMENT
 629 #endif
 630
 631 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 632         "hwconfig=fsl_ddr:bank_intlv=cs0_cs1;"                  \
 633         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
 634         "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 635         "netdev=eth0\0"                                         \
 636         "video-mode=" __stringify(DIU_ENVIRONMENT) "\0"         \
 637         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 638         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 639         "tftpflash=tftpboot $loadaddr $uboot && "               \
 640         "protect off $ubootaddr +$filesize && "                 \
 641         "erase $ubootaddr +$filesize && "                       \
 642         "cp.b $loadaddr $ubootaddr $filesize && "               \
 643         "protect on $ubootaddr +$filesize && "                  \
 644         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 645         "consoledev=ttyS0\0"                                    \
 646         "ramdiskaddr=2000000\0"                                 \
 647         "ramdiskfile=" __stringify(RAMDISKFILE) "\0"            \
 648         "fdtaddr=1e00000\0"                                     \
 649         "fdtfile=" __stringify(FDTFILE) "\0"                    \
 650         "bdev=sda3\0"
 651
 652 #define LINUXBOOTCOMMAND                       \
 653         "setenv bootargs root=/dev/ram rw "            \
 654         "console=$consoledev,$baudrate $othbootargs;"  \
 655         "setenv ramdiskaddr 0x02000000;"               \
 656         "setenv fdtaddr 0x00c00000;"                   \
 657         "setenv loadaddr 0x1000000;"                   \
 658         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 659
 660 #define HDBOOT                                  \
 661         "setenv bootargs root=/dev/$bdev rw "           \
 662         "console=$consoledev,$baudrate $othbootargs;"   \
 663         "tftp $loadaddr $bootfile;"                     \
 664         "tftp $fdtaddr $fdtfile;"                       \
 665         "bootm $loadaddr - $fdtaddr"
 666
 667 #define NFSBOOTCOMMAND                  \
 668         "setenv bootargs root=/dev/nfs rw "     \
 669         "nfsroot=$serverip:$rootpath "          \
 670         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 671         "console=$consoledev,$baudrate $othbootargs;"   \
 672         "tftp $loadaddr $bootfile;"             \
 673         "tftp $fdtaddr $fdtfile;"               \
 674         "bootm $loadaddr - $fdtaddr"
 675
 676 #define RAMBOOTCOMMAND                          \
 677         "setenv bootargs root=/dev/ram rw "             \
 678         "console=$consoledev,$baudrate $othbootargs;"   \
 679         "tftp $ramdiskaddr $ramdiskfile;"               \
 680         "tftp $loadaddr $bootfile;"                     \
 681         "tftp $fdtaddr $fdtfile;"                       \
 682         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 683
 684 #define CONFIG_BOOTCOMMAND              LINUXBOOTCOMMAND
 685
 686 #include <asm/fsl_secure_boot.h>
 687
 688 #endif  /* __CONFIG_H */