include/configs/P2041RDB.h

   1 /*
   2  * Copyright 2011-2012 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * P2041 RDB board configuration file
   9  * Also supports P2040 RDB
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 #ifdef CONFIG_RAMBOOT_PBL
  15 #define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
  16 #define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
  17 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg
  18 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg
  19 #endif
  20
  21 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  22 /* Set 1M boot space */
  23 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  24 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  25                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  26 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  27 #endif
  28
  29 /* High Level Configuration Options */
  30 #define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
  31 #define CONFIG_MP                       /* support multiple processors */
  32
  33 #ifndef CONFIG_SYS_TEXT_BASE
  34 #define CONFIG_SYS_TEXT_BASE    0xeff40000
  35 #endif
  36
  37 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  38 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  39 #endif
  40
  41 #define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
  42 #define CONFIG_SYS_NUM_CPC              CONFIG_SYS_NUM_DDR_CTLRS
  43 #define CONFIG_PCIE1                    /* PCIE controller 1 */
  44 #define CONFIG_PCIE2                    /* PCIE controller 2 */
  45 #define CONFIG_PCIE3                    /* PCIE controller 3 */
  46 #define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
  47 #define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */
  48
  49 #define CONFIG_SYS_SRIO
  50 #define CONFIG_SRIO1                    /* SRIO port 1 */
  51 #define CONFIG_SRIO2                    /* SRIO port 2 */
  52 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  53 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
  54
  55 #define CONFIG_ENV_OVERWRITE
  56
  57 #ifndef CONFIG_MTD_NOR_FLASH
  58 #else
  59 #define CONFIG_FLASH_CFI_DRIVER
  60 #define CONFIG_SYS_FLASH_CFI
  61 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
  62 #endif
  63
  64 #if defined(CONFIG_SPIFLASH)
  65         #define CONFIG_SYS_EXTRA_ENV_RELOC
  66         #define CONFIG_ENV_IS_IN_SPI_FLASH
  67         #define CONFIG_ENV_SPI_BUS              0
  68         #define CONFIG_ENV_SPI_CS               0
  69         #define CONFIG_ENV_SPI_MAX_HZ           10000000
  70         #define CONFIG_ENV_SPI_MODE             0
  71         #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
  72         #define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
  73         #define CONFIG_ENV_SECT_SIZE            0x10000
  74 #elif defined(CONFIG_SDCARD)
  75         #define CONFIG_SYS_EXTRA_ENV_RELOC
  76         #define CONFIG_FSL_FIXED_MMC_LOCATION
  77         #define CONFIG_SYS_MMC_ENV_DEV          0
  78         #define CONFIG_ENV_SIZE                 0x2000
  79         #define CONFIG_ENV_OFFSET               (512 * 1658)
  80 #elif defined(CONFIG_NAND)
  81 #define CONFIG_SYS_EXTRA_ENV_RELOC
  82 #define CONFIG_ENV_SIZE                 CONFIG_SYS_NAND_BLOCK_SIZE
  83 #define CONFIG_ENV_OFFSET               (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
  84 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
  85 #define CONFIG_ENV_IS_IN_REMOTE
  86 #define CONFIG_ENV_ADDR         0xffe20000
  87 #define CONFIG_ENV_SIZE         0x2000
  88 #elif defined(CONFIG_ENV_IS_NOWHERE)
  89 #define CONFIG_ENV_SIZE         0x2000
  90 #else
  91         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE \
  92                         - CONFIG_ENV_SECT_SIZE)
  93         #define CONFIG_ENV_SIZE         0x2000
  94         #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
  95 #endif
  96
  97 #ifndef __ASSEMBLY__
  98 unsigned long get_board_sys_clk(unsigned long dummy);
  99 #endif
 100 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
 101
 102 /*
 103  * These can be toggled for performance analysis, otherwise use default.
 104  */
 105 #define CONFIG_SYS_CACHE_STASHING
 106 #define CONFIG_BACKSIDE_L2_CACHE
 107 #define CONFIG_SYS_INIT_L2CSR0          L2CSR0_L2E
 108 #define CONFIG_BTB                      /* toggle branch predition */
 109
 110 #define CONFIG_ENABLE_36BIT_PHYS
 111
 112 #ifdef CONFIG_PHYS_64BIT
 113 #define CONFIG_ADDR_MAP
 114 #define CONFIG_SYS_NUM_ADDR_MAP         64      /* number of TLB1 entries */
 115 #endif
 116
 117 #define CONFIG_POST CONFIG_SYS_POST_MEMORY      /* test POST memory test */
 118 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
 119 #define CONFIG_SYS_MEMTEST_END          0x00400000
 120 #define CONFIG_SYS_ALT_MEMTEST
 121 #define CONFIG_PANIC_HANG       /* do not reset board on panic */
 122
 123 /*
 124  *  Config the L3 Cache as L3 SRAM
 125  */
 126 #define CONFIG_SYS_INIT_L3_ADDR         CONFIG_RAMBOOT_TEXT_BASE
 127 #ifdef CONFIG_PHYS_64BIT
 128 #define CONFIG_SYS_INIT_L3_ADDR_PHYS    (0xf00000000ull | \
 129                 CONFIG_RAMBOOT_TEXT_BASE)
 130 #else
 131 #define CONFIG_SYS_INIT_L3_ADDR_PHYS    CONFIG_SYS_INIT_L3_ADDR
 132 #endif
 133 #define CONFIG_SYS_L3_SIZE              (1024 << 10)
 134 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
 135
 136 #ifdef CONFIG_PHYS_64BIT
 137 #define CONFIG_SYS_DCSRBAR              0xf0000000
 138 #define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
 139 #endif
 140
 141 /* EEPROM */
 142 #define CONFIG_ID_EEPROM
 143 #define CONFIG_SYS_I2C_EEPROM_NXID
 144 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 145 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 146 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 147
 148 /*
 149  * DDR Setup
 150  */
 151 #define CONFIG_VERY_BIG_RAM
 152 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 153 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 154
 155 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 156 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 157
 158 #define CONFIG_DDR_SPD
 159
 160 #define CONFIG_SYS_SPD_BUS_NUM  0
 161 #define SPD_EEPROM_ADDRESS      0x52
 162 #define CONFIG_SYS_SDRAM_SIZE   4096    /* for fixed parameter use */
 163
 164 /*
 165  * Local Bus Definitions
 166  */
 167
 168 /* Set the local bus clock 1/8 of platform clock */
 169 #define CONFIG_SYS_LBC_LCRR             LCRR_CLKDIV_8
 170
 171 /*
 172  * This board doesn't have a promjet connector.
 173  * However, it uses commone corenet board LAW and TLB.
 174  * It is necessary to use the same start address with proper offset.
 175  */
 176 #define CONFIG_SYS_FLASH_BASE           0xe0000000
 177 #ifdef CONFIG_PHYS_64BIT
 178 #define CONFIG_SYS_FLASH_BASE_PHYS      0xfe0000000ull
 179 #else
 180 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 181 #endif
 182
 183 #define CONFIG_SYS_FLASH_BR_PRELIM \
 184                 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \
 185                 BR_PS_16 | BR_V)
 186 #define CONFIG_SYS_FLASH_OR_PRELIM \
 187                 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
 188                  | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)
 189
 190 #define CONFIG_FSL_CPLD
 191 #define CPLD_BASE               0xffdf0000      /* CPLD registers */
 192 #ifdef CONFIG_PHYS_64BIT
 193 #define CPLD_BASE_PHYS          0xfffdf0000ull
 194 #else
 195 #define CPLD_BASE_PHYS          CPLD_BASE
 196 #endif
 197
 198 #define CONFIG_SYS_BR3_PRELIM   (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V)
 199 #define CONFIG_SYS_OR3_PRELIM   0xffffeff7      /* 32KB but only 4k mapped */
 200
 201 #define PIXIS_LBMAP_SWITCH      7
 202 #define PIXIS_LBMAP_MASK        0xf0
 203 #define PIXIS_LBMAP_SHIFT       4
 204 #define PIXIS_LBMAP_ALTBANK     0x40
 205
 206 #define CONFIG_SYS_FLASH_QUIET_TEST
 207 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 208
 209 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 210 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 211 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Erase Timeout (ms) */
 212 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Write Timeout (ms) */
 213
 214 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 215
 216 #if defined(CONFIG_RAMBOOT_PBL)
 217 #define CONFIG_SYS_RAMBOOT
 218 #endif
 219
 220 #define CONFIG_NAND_FSL_ELBC
 221 /* Nand Flash */
 222 #ifdef CONFIG_NAND_FSL_ELBC
 223 #define CONFIG_SYS_NAND_BASE            0xffa00000
 224 #ifdef CONFIG_PHYS_64BIT
 225 #define CONFIG_SYS_NAND_BASE_PHYS       0xfffa00000ull
 226 #else
 227 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
 228 #endif
 229
 230 #define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
 231 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 232 #define CONFIG_CMD_NAND
 233 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
 234
 235 /* NAND flash config */
 236 #define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 237                                | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
 238                                | BR_PS_8               /* Port Size = 8 bit */ \
 239                                | BR_MS_FCM             /* MSEL = FCM */ \
 240                                | BR_V)                 /* valid */
 241 #define CONFIG_SYS_NAND_OR_PRELIM  (0xFFFC0000        /* length 256K */ \
 242                                | OR_FCM_PGS            /* Large Page*/ \
 243                                | OR_FCM_CSCT \
 244                                | OR_FCM_CST \
 245                                | OR_FCM_CHT \
 246                                | OR_FCM_SCY_1 \
 247                                | OR_FCM_TRLX \
 248                                | OR_FCM_EHTR)
 249
 250 #ifdef CONFIG_NAND
 251 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 252 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 253 #define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
 254 #define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
 255 #else
 256 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
 257 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
 258 #define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 259 #define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 260 #endif
 261 #else
 262 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
 263 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
 264 #endif /* CONFIG_NAND_FSL_ELBC */
 265
 266 #define CONFIG_SYS_FLASH_EMPTY_INFO
 267 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
 268 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
 269
 270 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 271 #define CONFIG_MISC_INIT_R
 272
 273 #define CONFIG_HWCONFIG
 274
 275 /* define to use L1 as initial stack */
 276 #define CONFIG_L1_INIT_RAM
 277 #define CONFIG_SYS_INIT_RAM_LOCK
 278 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* Initial L1 address */
 279 #ifdef CONFIG_PHYS_64BIT
 280 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
 281 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
 282 /* The assembler doesn't like typecast */
 283 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 284         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 285           CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 286 #else
 287 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
 288 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 289 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 290 #endif
 291 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 292
 293 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 294                                         GENERATED_GBL_DATA_SIZE)
 295 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 296
 297 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 298 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)
 299
 300 /* Serial Port - controlled on board with jumper J8
 301  * open - index 2
 302  * shorted - index 1
 303  */
 304 #define CONFIG_CONS_INDEX       1
 305 #define CONFIG_SYS_NS16550_SERIAL
 306 #define CONFIG_SYS_NS16550_REG_SIZE     1
 307 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 308
 309 #define CONFIG_SYS_BAUDRATE_TABLE       \
 310         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 311
 312 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 313 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 314 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 315 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 316
 317 /* I2C */
 318 #define CONFIG_SYS_I2C
 319 #define CONFIG_SYS_I2C_FSL
 320 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 321 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 322 #define CONFIG_SYS_FSL_I2C_OFFSET       0x118000
 323 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 324 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 325 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x118100
 326
 327 /*
 328  * RapidIO
 329  */
 330 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 331 #ifdef CONFIG_PHYS_64BIT
 332 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 333 #else
 334 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xa0000000
 335 #endif
 336 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000      /* 256M */
 337
 338 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 339 #ifdef CONFIG_PHYS_64BIT
 340 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 341 #else
 342 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xb0000000
 343 #endif
 344 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000      /* 256M */
 345
 346 /*
 347  * for slave u-boot IMAGE instored in master memory space,
 348  * PHYS must be aligned based on the SIZE
 349  */
 350 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 351 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 352 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000       /* 1M */
 353 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 354 /*
 355  * for slave UCODE and ENV instored in master memory space,
 356  * PHYS must be aligned based on the SIZE
 357  */
 358 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 359 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 360 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000    /* 256K */
 361
 362 /* slave core release by master*/
 363 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 364 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 365
 366 /*
 367  * SRIO_PCIE_BOOT - SLAVE
 368  */
 369 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 370 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 371 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 372                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 373 #endif
 374
 375 /*
 376  * eSPI - Enhanced SPI
 377  */
 378 #define CONFIG_SF_DEFAULT_SPEED         10000000
 379 #define CONFIG_SF_DEFAULT_MODE          0
 380
 381 /*
 382  * General PCI
 383  * Memory space is mapped 1-1, but I/O space must start from 0.
 384  */
 385
 386 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 387 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 388 #ifdef CONFIG_PHYS_64BIT
 389 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 390 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 391 #else
 392 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 393 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 394 #endif
 395 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 396 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 397 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 398 #ifdef CONFIG_PHYS_64BIT
 399 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 400 #else
 401 #define CONFIG_SYS_PCIE1_IO_PHYS        0xf8000000
 402 #endif
 403 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 404
 405 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 406 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 407 #ifdef CONFIG_PHYS_64BIT
 408 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 409 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 410 #else
 411 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
 412 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
 413 #endif
 414 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 415 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 416 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 417 #ifdef CONFIG_PHYS_64BIT
 418 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 419 #else
 420 #define CONFIG_SYS_PCIE2_IO_PHYS        0xf8010000
 421 #endif
 422 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 423
 424 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 425 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xc0000000
 426 #ifdef CONFIG_PHYS_64BIT
 427 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 428 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc40000000ull
 429 #else
 430 #define CONFIG_SYS_PCIE3_MEM_BUS        0xc0000000
 431 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc0000000
 432 #endif
 433 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x20000000      /* 512M */
 434 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 435 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 436 #ifdef CONFIG_PHYS_64BIT
 437 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 438 #else
 439 #define CONFIG_SYS_PCIE3_IO_PHYS        0xf8020000
 440 #endif
 441 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 442
 443 /* Qman/Bman */
 444 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
 445 #define CONFIG_SYS_BMAN_NUM_PORTALS     10
 446 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 447 #ifdef CONFIG_PHYS_64BIT
 448 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 449 #else
 450 #define CONFIG_SYS_BMAN_MEM_PHYS        CONFIG_SYS_BMAN_MEM_BASE
 451 #endif
 452 #define CONFIG_SYS_BMAN_MEM_SIZE        0x00200000
 453 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 454 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 455 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 456 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 457 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 458                                         CONFIG_SYS_BMAN_CENA_SIZE)
 459 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 460 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 461 #define CONFIG_SYS_QMAN_NUM_PORTALS     10
 462 #define CONFIG_SYS_QMAN_MEM_BASE        0xf4200000
 463 #ifdef CONFIG_PHYS_64BIT
 464 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff4200000ull
 465 #else
 466 #define CONFIG_SYS_QMAN_MEM_PHYS        CONFIG_SYS_QMAN_MEM_BASE
 467 #endif
 468 #define CONFIG_SYS_QMAN_MEM_SIZE        0x00200000
 469 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 470 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 471 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 472 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 473 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 474                                         CONFIG_SYS_QMAN_CENA_SIZE)
 475 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 476 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 477
 478 #define CONFIG_SYS_DPAA_FMAN
 479 #define CONFIG_SYS_DPAA_PME
 480 /* Default address of microcode for the Linux Fman driver */
 481 #if defined(CONFIG_SPIFLASH)
 482 /*
 483  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 484  * env, so we got 0x110000.
 485  */
 486 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 487 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000
 488 #elif defined(CONFIG_SDCARD)
 489 /*
 490  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 491  * about 825KB (1650 blocks), Env is stored after the image, and the env size is
 492  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
 493  */
 494 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 495 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
 496 #elif defined(CONFIG_NAND)
 497 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 498 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 499 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 500 /*
 501  * Slave has no ucode locally, it can fetch this from remote. When implementing
 502  * in two corenet boards, slave's ucode could be stored in master's memory
 503  * space, the address can be mapped from slave TLB->slave LAW->
 504  * slave SRIO or PCIE outbound window->master inbound window->
 505  * master LAW->the ucode address in master's memory space.
 506  */
 507 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
 508 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
 509 #else
 510 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 511 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
 512 #endif
 513 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 514 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 515
 516 #ifdef CONFIG_SYS_DPAA_FMAN
 517 #define CONFIG_FMAN_ENET
 518 #define CONFIG_PHYLIB_10G
 519 #define CONFIG_PHY_VITESSE
 520 #define CONFIG_PHY_TERANETICS
 521 #endif
 522
 523 #ifdef CONFIG_PCI
 524 #define CONFIG_PCI_INDIRECT_BRIDGE
 525
 526 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 527 #endif  /* CONFIG_PCI */
 528
 529 /* SATA */
 530 #define CONFIG_FSL_SATA_V2
 531
 532 #ifdef CONFIG_FSL_SATA_V2
 533 #define CONFIG_FSL_SATA
 534 #define CONFIG_LIBATA
 535
 536 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 537 #define CONFIG_SATA1
 538 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 539 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 540 #define CONFIG_SATA2
 541 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 542 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 543
 544 #define CONFIG_LBA48
 545 #endif
 546
 547 #ifdef CONFIG_FMAN_ENET
 548 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR  0x2
 549 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR  0x3
 550 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR  0x4
 551 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR  0x1
 552 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR  0x0
 553
 554 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
 555 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
 556 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
 557 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f
 558
 559 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR  0
 560
 561 #define CONFIG_SYS_TBIPA_VALUE  8
 562 #define CONFIG_MII              /* MII PHY management */
 563 #define CONFIG_ETHPRIME         "FM1@DTSEC1"
 564 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 565 #endif
 566
 567 /*
 568  * Environment
 569  */
 570 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 571 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 572
 573 /*
 574  * Command line configuration.
 575  */
 576
 577 #ifdef CONFIG_PCI
 578 #define CONFIG_CMD_PCI
 579 #endif
 580
 581 /*
 582 * USB
 583 */
 584 #define CONFIG_HAS_FSL_DR_USB
 585 #define CONFIG_HAS_FSL_MPH_USB
 586
 587 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
 588 #define CONFIG_USB_EHCI_FSL
 589 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 590 #endif
 591
 592 #ifdef CONFIG_MMC
 593 #define CONFIG_FSL_ESDHC
 594 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 595 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 596 #endif
 597
 598 /*
 599  * Miscellaneous configurable options
 600  */
 601 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 602 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 603 #define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
 604 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 605 #ifdef CONFIG_CMD_KGDB
 606 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 607 #else
 608 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 609 #endif
 610 /* Print Buffer Size */
 611 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
 612                                 sizeof(CONFIG_SYS_PROMPT)+16)
 613 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 614 /* Boot Argument Buffer Size */
 615 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 616
 617 /*
 618  * For booting Linux, the board info and command line data
 619  * have to be in the first 64 MB of memory, since this is
 620  * the maximum mapped by the Linux kernel during initialization.
 621  */
 622 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux */
 623 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 624
 625 #ifdef CONFIG_CMD_KGDB
 626 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 627 #endif
 628
 629 /*
 630  * Environment Configuration
 631  */
 632 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 633 #define CONFIG_BOOTFILE         "uImage"
 634 #define CONFIG_UBOOTPATH        u-boot.bin
 635
 636 /* default location for tftp and bootm */
 637 #define CONFIG_LOADADDR         1000000
 638
 639 #define __USB_PHY_TYPE  utmi
 640
 641 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 642         "hwconfig=fsl_ddr:ctlr_intlv=cacheline,"                \
 643         "bank_intlv=cs0_cs1\0"                                  \
 644         "netdev=eth0\0"                                         \
 645         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
 646         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"             \
 647         "tftpflash=tftpboot $loadaddr $uboot && "               \
 648         "protect off $ubootaddr +$filesize && "                 \
 649         "erase $ubootaddr +$filesize && "                       \
 650         "cp.b $loadaddr $ubootaddr $filesize && "               \
 651         "protect on $ubootaddr +$filesize && "                  \
 652         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 653         "consoledev=ttyS0\0"                                    \
 654         "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"                \
 655         "usb_dr_mode=host\0"                                    \
 656         "ramdiskaddr=2000000\0"                                 \
 657         "ramdiskfile=p2041rdb/ramdisk.uboot\0"                  \
 658         "fdtaddr=1e00000\0"                                     \
 659         "fdtfile=p2041rdb/p2041rdb.dtb\0"                       \
 660         "bdev=sda3\0"
 661
 662 #define CONFIG_HDBOOT                                   \
 663         "setenv bootargs root=/dev/$bdev rw "           \
 664         "console=$consoledev,$baudrate $othbootargs;"   \
 665         "tftp $loadaddr $bootfile;"                     \
 666         "tftp $fdtaddr $fdtfile;"                       \
 667         "bootm $loadaddr - $fdtaddr"
 668
 669 #define CONFIG_NFSBOOTCOMMAND                   \
 670         "setenv bootargs root=/dev/nfs rw "     \
 671         "nfsroot=$serverip:$rootpath "          \
 672         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 673         "console=$consoledev,$baudrate $othbootargs;"   \
 674         "tftp $loadaddr $bootfile;"             \
 675         "tftp $fdtaddr $fdtfile;"               \
 676         "bootm $loadaddr - $fdtaddr"
 677
 678 #define CONFIG_RAMBOOTCOMMAND                           \
 679         "setenv bootargs root=/dev/ram rw "             \
 680         "console=$consoledev,$baudrate $othbootargs;"   \
 681         "tftp $ramdiskaddr $ramdiskfile;"               \
 682         "tftp $loadaddr $bootfile;"                     \
 683         "tftp $fdtaddr $fdtfile;"                       \
 684         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 685
 686 #define CONFIG_BOOTCOMMAND              CONFIG_HDBOOT
 687
 688 #include <asm/fsl_secure_boot.h>
 689
 690 #endif  /* __CONFIG_H */