2 * Copyright 2013 Freescale Semiconductor, Inc.
4 * Authors: Roy Zang <tie-fei.zang@freescale.com>
5 * Chunhe Lan <Chunhe.Lan@freescale.com>
7 * SPDX-License-Identifier: GPL-2.0+
13 #ifndef CONFIG_SYS_TEXT_BASE
14 #define CONFIG_SYS_TEXT_BASE 0xeff40000
17 #ifndef CONFIG_SYS_MONITOR_BASE
18 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
21 #ifndef CONFIG_RESET_VECTOR_ADDRESS
22 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
25 /* High Level Configuration Options */
26 #define CONFIG_MP /* support multiple processors */
28 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
29 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
30 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
31 #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
32 #define CONFIG_PCIE3 /* PCIE controller 3 (slot 3) */
33 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
34 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
35 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
38 extern unsigned long get_clock_freq(void);
41 #define CONFIG_SYS_CLK_FREQ 66666666
42 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ
45 * These can be toggled for performance analysis, otherwise use default.
47 #define CONFIG_L2_CACHE /* toggle L2 cache */
48 #define CONFIG_BTB /* toggle branch predition */
49 #define CONFIG_HWCONFIG
51 #define CONFIG_ENABLE_36BIT_PHYS
53 #define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
54 #define CONFIG_SYS_MEMTEST_END 0x02000000
56 #define CONFIG_PANIC_HANG /* do not reset board on panic */
58 /* Implement conversion of addresses in the LBC */
59 #define CONFIG_SYS_LBC_LBCR 0x00000000
60 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8
63 #define CONFIG_VERY_BIG_RAM
64 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
65 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
67 #define CONFIG_DIMM_SLOTS_PER_CTLR 1
68 #define CONFIG_CHIP_SELECTS_PER_CTRL 1
70 #define CONFIG_DDR_SPD
71 #define CONFIG_FSL_DDR_INTERACTIVE
72 #define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */
73 #define CONFIG_SYS_SPD_BUS_NUM 0
74 #define SPD_EEPROM_ADDRESS 0x50
75 #define CONFIG_SYS_DDR_RAW_TIMING
80 * 0x0000_0000 0x1fff_ffff DDR 512M cacheable
81 * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
82 * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
83 * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
84 * 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M cacheable
85 * 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
86 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable TLB0
88 * Localbus non-cacheable
90 * 0xec00_0000 0xefff_ffff NOR flash 64M non-cacheable
91 * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
95 * Local Bus Definitions
97 #define CONFIG_SYS_FLASH_BASE 0xec000000 /* start of FLASH 64M */
98 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
100 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
102 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
104 #define CONFIG_FLASH_CFI_DRIVER
105 #define CONFIG_SYS_FLASH_CFI
106 #define CONFIG_SYS_FLASH_EMPTY_INFO
107 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
108 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
109 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
110 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
112 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
114 #define CONFIG_SYS_INIT_RAM_LOCK
115 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
116 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */
117 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
118 GENERATED_GBL_DATA_SIZE)
119 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
121 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) /* Reserve 512 kB for Mon */
122 #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
124 #define CONFIG_SYS_NAND_BASE 0xffa00000
125 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
127 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
128 #define CONFIG_SYS_MAX_NAND_DEVICE 1
129 #define CONFIG_CMD_NAND
130 #define CONFIG_NAND_FSL_ELBC
131 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
133 /* NAND flash config */
134 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
135 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
136 | BR_PS_8 /* Port Size = 8bit */ \
137 | BR_MS_FCM /* MSEL = FCM */ \
139 #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
148 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
149 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
150 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
151 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
154 #define CONFIG_CONS_INDEX 1
155 #undef CONFIG_SERIAL_SOFTWARE_FIFO
156 #define CONFIG_SYS_NS16550_SERIAL
157 #define CONFIG_SYS_NS16550_REG_SIZE 1
158 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
160 #define CONFIG_SYS_BAUDRATE_TABLE \
161 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
163 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
164 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
167 #define CONFIG_SYS_I2C
168 #define CONFIG_SYS_I2C_FSL
169 #define CONFIG_SYS_FSL_I2C_SPEED 400000
170 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
171 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
172 #define CONFIG_SYS_FSL_I2C2_SPEED 400000
173 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
174 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
179 #define CONFIG_ID_EEPROM
180 #ifdef CONFIG_ID_EEPROM
181 #define CONFIG_SYS_I2C_EEPROM_NXID
183 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
184 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
185 #define CONFIG_SYS_EEPROM_BUS_NUM 0
189 * Memory space is mapped 1-1, but I/O space must start from 0.
192 /* controller 3, Slot 1, tgtid 3, Base address b000 */
193 #define CONFIG_SYS_PCIE3_NAME "Slot 3"
194 #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
195 #define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
196 #define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
197 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
198 #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
199 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
200 #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
201 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
203 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
204 #define CONFIG_SYS_PCIE2_NAME "Slot 2"
205 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
206 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
207 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
208 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
209 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
210 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
211 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
212 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
214 /* controller 1, Slot 2, tgtid 1, Base address a000 */
215 #define CONFIG_SYS_PCIE1_NAME "Slot 1"
216 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
217 #define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
218 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
219 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
220 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
221 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
222 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
223 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
225 #if defined(CONFIG_PCI)
226 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
227 #endif /* CONFIG_PCI */
232 #define CONFIG_ENV_OVERWRITE
234 #define CONFIG_ENV_IS_IN_FLASH
235 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
236 #define CONFIG_ENV_SIZE 0x2000
237 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
239 #define CONFIG_LOADS_ECHO /* echo on for serial download */
240 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
243 * Command line configuration.
245 #define CONFIG_CMD_IRQ
246 #define CONFIG_CMD_REGINFO
248 #if defined(CONFIG_PCI)
249 #define CONFIG_CMD_PCI
255 #define CONFIG_HAS_FSL_DR_USB
256 #ifdef CONFIG_HAS_FSL_DR_USB
257 #define CONFIG_USB_EHCI
259 #ifdef CONFIG_USB_EHCI
260 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
261 #define CONFIG_USB_EHCI_FSL
266 * Miscellaneous configurable options
268 #define CONFIG_SYS_LONGHELP /* undef to save memory */
269 #define CONFIG_CMDLINE_EDITING /* Command-line editing */
270 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
271 #if defined(CONFIG_CMD_KGDB)
272 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
274 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
276 /* Print Buffer Size */
277 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
278 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
279 /* Boot Argument Buffer Size */
280 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
283 * For booting Linux, the board info and command line data
284 * have to be in the first 64 MB of memory, since this is
285 * the maximum mapped by the Linux kernel during initialization.
287 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
288 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
291 * Environment Configuration
293 #define CONFIG_BOOTFILE "uImage"
294 #define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */
296 /* default location for tftp and bootm */
297 #define CONFIG_LOADADDR 1000000
300 #define CONFIG_BAUDRATE 115200
303 #define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */
304 #define CONFIG_SYS_QMAN_MEM_BASE 0xff000000
305 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
306 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
307 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
308 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
309 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
310 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
311 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
312 CONFIG_SYS_QMAN_CENA_SIZE)
313 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
314 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
315 #define CONFIG_SYS_BMAN_MEM_BASE 0xff200000
316 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
317 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
318 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
319 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
320 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
321 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
322 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
323 CONFIG_SYS_BMAN_CENA_SIZE)
324 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
325 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
328 #define CONFIG_SYS_DPAA_FMAN
329 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
331 #ifdef CONFIG_SYS_DPAA_FMAN
332 #define CONFIG_FMAN_ENET
333 #define CONFIG_PHY_ATHEROS
336 /* Default address of microcode for the Linux Fman driver */
337 /* QE microcode/firmware address */
338 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
339 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
340 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
341 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
343 #ifdef CONFIG_FMAN_ENET
344 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1
345 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x2
347 #define CONFIG_SYS_TBIPA_VALUE 8
348 #define CONFIG_MII /* MII PHY management */
349 #define CONFIG_ETHPRIME "FM1@DTSEC1"
352 #define CONFIG_EXTRA_ENV_SETTINGS \
354 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
355 "loadaddr=1000000\0" \
356 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
357 "tftpflash=tftpboot $loadaddr $uboot; " \
358 "protect off $ubootaddr +$filesize; " \
359 "erase $ubootaddr +$filesize; " \
360 "cp.b $loadaddr $ubootaddr $filesize; " \
361 "protect on $ubootaddr +$filesize; " \
362 "cmp.b $loadaddr $ubootaddr $filesize\0" \
363 "consoledev=ttyS0\0" \
364 "ramdiskaddr=2000000\0" \
365 "ramdiskfile=rootfs.ext2.gz.uboot\0" \
366 "fdtaddr=1e00000\0" \
367 "fdtfile=p1023rdb.dtb\0" \
368 "othbootargs=ramdisk_size=600000\0" \
370 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
372 #define CONFIG_HDBOOT \
373 "setenv bootargs root=/dev/$bdev rw " \
374 "console=$consoledev,$baudrate $othbootargs;" \
375 "tftp $loadaddr $bootfile;" \
376 "tftp $fdtaddr $fdtfile;" \
377 "bootm $loadaddr - $fdtaddr"
379 #define CONFIG_NFSBOOTCOMMAND \
380 "setenv bootargs root=/dev/nfs rw " \
381 "nfsroot=$serverip:$rootpath " \
382 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
383 "console=$consoledev,$baudrate $othbootargs;" \
384 "tftp $loadaddr $bootfile;" \
385 "tftp $fdtaddr $fdtfile;" \
386 "bootm $loadaddr - $fdtaddr"
388 #define CONFIG_RAMBOOTCOMMAND \
389 "setenv bootargs root=/dev/ram rw " \
390 "console=$consoledev,$baudrate $othbootargs;" \
391 "tftp $ramdiskaddr $ramdiskfile;" \
392 "tftp $loadaddr $bootfile;" \
393 "tftp $fdtaddr $fdtfile;" \
394 "bootm $loadaddr $ramdiskaddr $fdtaddr"
396 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
398 #endif /* __CONFIG_H */