include/configs/MPC8641HPCN.h

   1 /*
   2  * Copyright 2006, 2010-2011 Freescale Semiconductor.
   3  *
   4  * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /*
  10  * MPC8641HPCN board configuration file
  11  *
  12  * Make sure you change the MAC address and other network params first,
  13  * search for CONFIG_SERVERIP, etc. in this file.
  14  */
  15
  16 #ifndef __CONFIG_H
  17 #define __CONFIG_H
  18
  19 #define CONFIG_DISPLAY_BOARDINFO
  20
  21 /* High Level Configuration Options */
  22 #define CONFIG_MPC8641          1       /* MPC8641 specific */
  23 #define CONFIG_MPC8641HPCN      1       /* MPC8641HPCN board specific */
  24 #define CONFIG_MP               1       /* support multiple processors */
  25 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
  26 /*#define CONFIG_PHYS_64BIT     1*/     /* Place devices in 36-bit space */
  27 #define CONFIG_ADDR_MAP         1       /* Use addr map */
  28
  29 /*
  30  * default CCSRBAR is at 0xff700000
  31  * assume U-Boot is less than 0.5MB
  32  */
  33 #define CONFIG_SYS_TEXT_BASE    0xeff00000
  34
  35 #ifdef RUN_DIAG
  36 #define CONFIG_SYS_DIAG_ADDR         CONFIG_SYS_FLASH_BASE
  37 #endif
  38
  39 /*
  40  * virtual address to be used for temporary mappings.  There
  41  * should be 128k free at this VA.
  42  */
  43 #define CONFIG_SYS_SCRATCH_VA   0xe0000000
  44
  45 #define CONFIG_SYS_SRIO
  46 #define CONFIG_SRIO1                    /* SRIO port 1 */
  47
  48 #define CONFIG_PCI              1       /* Enable PCI/PCIE */
  49 #define CONFIG_PCIE1            1       /* PCIE controler 1 (ULI bridge) */
  50 #define CONFIG_PCIE2            1       /* PCIE controler 2 (slot) */
  51 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  52 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  53 #define CONFIG_FSL_LAW          1       /* Use common FSL law init code */
  54
  55 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
  56 #define CONFIG_ENV_OVERWRITE
  57
  58 #define CONFIG_BAT_RW           1       /* Use common BAT rw code */
  59 #define CONFIG_HIGH_BATS        1       /* High BATs supported and enabled */
  60 #define CONFIG_SYS_NUM_ADDR_MAP 8       /* Number of addr map slots = 8 dbats */
  61
  62 #define CONFIG_ALTIVEC          1
  63
  64 /*
  65  * L2CR setup -- make sure this is right for your board!
  66  */
  67 #define CONFIG_SYS_L2
  68 #define L2_INIT         0
  69 #define L2_ENABLE       (L2CR_L2E)
  70
  71 #ifndef CONFIG_SYS_CLK_FREQ
  72 #ifndef __ASSEMBLY__
  73 extern unsigned long get_board_sys_clk(unsigned long dummy);
  74 #endif
  75 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
  76 #endif
  77
  78 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  79 #define CONFIG_SYS_MEMTEST_END          0x00400000
  80
  81 /*
  82  * With the exception of PCI Memory and Rapid IO, most devices will simply
  83  * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA
  84  * when 36-bit is enabled.  When 36-bit is not enabled, these bits are 0.
  85  */
  86 #ifdef CONFIG_PHYS_64BIT
  87 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f
  88 #else
  89 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000
  90 #endif
  91
  92 /*
  93  * Base addresses -- Note these are effective addresses where the
  94  * actual resources get mapped (not physical addresses)
  95  */
  96 #define CONFIG_SYS_CCSRBAR_DEFAULT      0xff700000      /* CCSRBAR Default */
  97 #define CONFIG_SYS_CCSRBAR              0xffe00000      /* relocated CCSRBAR */
  98 #define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
  99
 100 /* Physical addresses */
 101 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
 102 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH    CONFIG_SYS_PHYS_ADDR_HIGH
 103 #define CONFIG_SYS_CCSRBAR_PHYS \
 104         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 105                             CONFIG_SYS_CCSRBAR_PHYS_HIGH)
 106
 107 #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */
 108
 109 /*
 110  * DDR Setup
 111  */
 112 #define CONFIG_SYS_FSL_DDR2
 113 #undef CONFIG_FSL_DDR_INTERACTIVE
 114 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
 115 #define CONFIG_DDR_SPD
 116
 117 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
 118 #define CONFIG_MEM_INIT_VALUE   0xDeadBeef
 119
 120 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
 121 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 122 #define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
 123 #define CONFIG_VERY_BIG_RAM
 124
 125 #define CONFIG_NUM_DDR_CONTROLLERS      2
 126 #define CONFIG_DIMM_SLOTS_PER_CTLR      2
 127 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 128
 129 /*
 130  * I2C addresses of SPD EEPROMs
 131  */
 132 #define SPD_EEPROM_ADDRESS1     0x51    /* CTLR 0 DIMM 0 */
 133 #define SPD_EEPROM_ADDRESS2     0x52    /* CTLR 0 DIMM 1 */
 134 #define SPD_EEPROM_ADDRESS3     0x53    /* CTLR 1 DIMM 0 */
 135 #define SPD_EEPROM_ADDRESS4     0x54    /* CTLR 1 DIMM 1 */
 136
 137
 138 /*
 139  * These are used when DDR doesn't use SPD.
 140  */
 141 #define CONFIG_SYS_SDRAM_SIZE           256             /* DDR is 256MB */
 142 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
 143 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80010102      /* Enable, no interleaving */
 144 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 145 #define CONFIG_SYS_DDR_TIMING_0 0x00260802
 146 #define CONFIG_SYS_DDR_TIMING_1 0x39357322
 147 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
 148 #define CONFIG_SYS_DDR_MODE_1           0x00480432
 149 #define CONFIG_SYS_DDR_MODE_2           0x00000000
 150 #define CONFIG_SYS_DDR_INTERVAL 0x06090100
 151 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 152 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
 153 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
 154 #define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
 155 #define CONFIG_SYS_DDR_CONTROL          0xe3008000      /* Type = DDR2 */
 156 #define CONFIG_SYS_DDR_CONTROL2 0x04400000
 157
 158 #define CONFIG_ID_EEPROM
 159 #define CONFIG_SYS_I2C_EEPROM_NXID
 160 #define CONFIG_ID_EEPROM
 161 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 162 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 163
 164 #define CONFIG_SYS_FLASH_BASE           0xef800000     /* start of FLASH 8M */
 165 #define CONFIG_SYS_FLASH_BASE_PHYS_LOW  CONFIG_SYS_FLASH_BASE
 166 #define CONFIG_SYS_FLASH_BASE_PHYS \
 167         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 168                             CONFIG_SYS_PHYS_ADDR_HIGH)
 169
 170 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
 171
 172 #define CONFIG_SYS_BR0_PRELIM   (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 173                                  | 0x00001001)  /* port size 16bit */
 174 #define CONFIG_SYS_OR0_PRELIM   0xff806ff7      /* 8MB Boot Flash area*/
 175
 176 #define CONFIG_SYS_BR2_PRELIM   (BR_PHYS_ADDR(CF_BASE_PHYS)             \
 177                                  | 0x00001001)  /* port size 16bit */
 178 #define CONFIG_SYS_OR2_PRELIM   0xffffeff7      /* 32k Compact Flash */
 179
 180 #define CONFIG_SYS_BR3_PRELIM   (BR_PHYS_ADDR(PIXIS_BASE_PHYS)  \
 181                                  | 0x00000801) /* port size 8bit */
 182 #define CONFIG_SYS_OR3_PRELIM   0xffffeff7      /* 32k PIXIS area*/
 183
 184 /*
 185  * The LBC_BASE is the base of the region that contains the PIXIS and the CF.
 186  * The PIXIS and CF by themselves aren't large enough to take up the 128k
 187  * required for the smallest BAT mapping, so there's a 64k hole.
 188  */
 189 #define CONFIG_SYS_LBC_BASE             0xffde0000
 190 #define CONFIG_SYS_LBC_BASE_PHYS_LOW    CONFIG_SYS_LBC_BASE
 191
 192 #define CONFIG_FSL_PIXIS        1       /* use common PIXIS code */
 193 #define PIXIS_BASE              (CONFIG_SYS_LBC_BASE + 0x00010000)
 194 #define PIXIS_BASE_PHYS_LOW     (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000)
 195 #define PIXIS_BASE_PHYS         PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \
 196                                                     CONFIG_SYS_PHYS_ADDR_HIGH)
 197 #define PIXIS_SIZE              0x00008000      /* 32k */
 198 #define PIXIS_ID                0x0     /* Board ID at offset 0 */
 199 #define PIXIS_VER               0x1     /* Board version at offset 1 */
 200 #define PIXIS_PVER              0x2     /* PIXIS FPGA version at offset 2 */
 201 #define PIXIS_RST               0x4     /* PIXIS Reset Control register */
 202 #define PIXIS_AUX               0x6     /* PIXIS Auxiliary register; Scratch register */
 203 #define PIXIS_SPD               0x7     /* Register for SYSCLK speed */
 204 #define PIXIS_VCTL              0x10    /* VELA Control Register */
 205 #define PIXIS_VCFGEN0           0x12    /* VELA Config Enable 0 */
 206 #define PIXIS_VCFGEN1           0x13    /* VELA Config Enable 1 */
 207 #define PIXIS_VBOOT             0x16    /* VELA VBOOT Register */
 208 #define PIXIS_VBOOT_FMAP        0x80    /* VBOOT - CFG_FLASHMAP */
 209 #define PIXIS_VBOOT_FBANK       0x40    /* VBOOT - CFG_FLASHBANK */
 210 #define PIXIS_VSPEED0           0x17    /* VELA VSpeed 0 */
 211 #define PIXIS_VSPEED1           0x18    /* VELA VSpeed 1 */
 212 #define PIXIS_VCLKH             0x19    /* VELA VCLKH register */
 213 #define PIXIS_VCLKL             0x1A    /* VELA VCLKL register */
 214 #define CONFIG_SYS_PIXIS_VBOOT_MASK     0x40    /* Reset altbank mask*/
 215
 216 /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */
 217 #define CF_BASE                 (PIXIS_BASE + PIXIS_SIZE)
 218 #define CF_BASE_PHYS            (PIXIS_BASE_PHYS + PIXIS_SIZE)
 219
 220 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 221 #define CONFIG_SYS_MAX_FLASH_SECT       128             /* sectors per device */
 222
 223 #undef  CONFIG_SYS_FLASH_CHECKSUM
 224 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 225 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 226 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE    /* start of monitor */
 227 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */
 228
 229 #define CONFIG_FLASH_CFI_DRIVER
 230 #define CONFIG_SYS_FLASH_CFI
 231 #define CONFIG_SYS_FLASH_EMPTY_INFO
 232
 233 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 234 #define CONFIG_SYS_RAMBOOT
 235 #else
 236 #undef  CONFIG_SYS_RAMBOOT
 237 #endif
 238
 239 #if defined(CONFIG_SYS_RAMBOOT)
 240 #undef CONFIG_SPD_EEPROM
 241 #define CONFIG_SYS_SDRAM_SIZE   256
 242 #endif
 243
 244 #undef CONFIG_CLOCKS_IN_MHZ
 245
 246 #define CONFIG_SYS_INIT_RAM_LOCK        1
 247 #ifndef CONFIG_SYS_INIT_RAM_LOCK
 248 #define CONFIG_SYS_INIT_RAM_ADDR        0x0fd00000      /* Initial RAM address */
 249 #else
 250 #define CONFIG_SYS_INIT_RAM_ADDR        0xf8400000      /* Initial RAM address */
 251 #endif
 252 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000          /* Size of used area in RAM */
 253
 254 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 255 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 256
 257 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 kB for Mon */
 258 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)    /* Reserved for malloc */
 259
 260 /* Serial Port */
 261 #define CONFIG_CONS_INDEX     1
 262 #define CONFIG_SYS_NS16550_SERIAL
 263 #define CONFIG_SYS_NS16550_REG_SIZE     1
 264 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 265
 266 #define CONFIG_SYS_BAUDRATE_TABLE  \
 267         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 268
 269 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 270 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 271
 272 /* Use the HUSH parser */
 273 #define CONFIG_SYS_HUSH_PARSER
 274
 275 /*
 276  * Pass open firmware flat tree to kernel
 277  */
 278 #define CONFIG_OF_LIBFDT                1
 279 #define CONFIG_OF_BOARD_SETUP           1
 280 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
 281
 282 /*
 283  * I2C
 284  */
 285 #define CONFIG_SYS_I2C
 286 #define CONFIG_SYS_I2C_FSL
 287 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 288 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 289 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3100
 290 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 291
 292 /*
 293  * RapidIO MMU
 294  */
 295 #define CONFIG_SYS_SRIO1_MEM_BASE       0x80000000      /* base address */
 296 #ifdef CONFIG_PHYS_64BIT
 297 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW   0x00000000
 298 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH  0x0000000c
 299 #else
 300 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW   CONFIG_SYS_SRIO1_MEM_BASE
 301 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH  0x00000000
 302 #endif
 303 #define CONFIG_SYS_SRIO1_MEM_PHYS \
 304         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 305                             CONFIG_SYS_SRIO1_MEM_PHYS_HIGH)
 306 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x20000000      /* 128M */
 307
 308 /*
 309  * General PCI
 310  * Addresses are mapped 1-1.
 311  */
 312
 313 #define CONFIG_SYS_PCIE1_NAME           "ULI"
 314 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 315 #ifdef CONFIG_PHYS_64BIT
 316 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 317 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW   0x00000000
 318 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH  0x0000000c
 319 #else
 320 #define CONFIG_SYS_PCIE1_MEM_BUS        CONFIG_SYS_PCIE1_MEM_VIRT
 321 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW   CONFIG_SYS_PCIE1_MEM_VIRT
 322 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH  0x00000000
 323 #endif
 324 #define CONFIG_SYS_PCIE1_MEM_PHYS \
 325         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 326                             CONFIG_SYS_PCIE1_MEM_PHYS_HIGH)
 327 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 328 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 329 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 330 #define CONFIG_SYS_PCIE1_IO_PHYS_LOW    CONFIG_SYS_PCIE1_IO_VIRT
 331 #define CONFIG_SYS_PCIE1_IO_PHYS \
 332         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 333                             CONFIG_SYS_PHYS_ADDR_HIGH)
 334 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64K */
 335
 336 #ifdef CONFIG_PHYS_64BIT
 337 /*
 338  * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT.
 339  * This will increase the amount of PCI address space available for
 340  * for mapping RAM.
 341  */
 342 #define CONFIG_SYS_PCIE2_MEM_BUS        CONFIG_SYS_PCIE1_MEM_BUS
 343 #else
 344 #define CONFIG_SYS_PCIE2_MEM_BUS        (CONFIG_SYS_PCIE1_MEM_BUS \
 345                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 346 #endif
 347 #define CONFIG_SYS_PCIE2_MEM_VIRT       (CONFIG_SYS_PCIE1_MEM_VIRT \
 348                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 349 #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW   (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \
 350                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 351 #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH  CONFIG_SYS_PCIE1_MEM_PHYS_HIGH
 352 #define CONFIG_SYS_PCIE2_MEM_PHYS       (CONFIG_SYS_PCIE1_MEM_PHYS \
 353                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 354 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 355 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 356 #define CONFIG_SYS_PCIE2_IO_VIRT        (CONFIG_SYS_PCIE1_IO_VIRT \
 357                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 358 #define CONFIG_SYS_PCIE2_IO_PHYS_LOW    (CONFIG_SYS_PCIE1_IO_PHYS_LOW \
 359                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 360 #define CONFIG_SYS_PCIE2_IO_PHYS        (CONFIG_SYS_PCIE1_IO_PHYS \
 361                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 362 #define CONFIG_SYS_PCIE2_IO_SIZE        CONFIG_SYS_PCIE1_IO_SIZE
 363
 364 #if defined(CONFIG_PCI)
 365
 366 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 367
 368 #undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE
 369
 370 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 371
 372 #define CONFIG_RTL8139
 373
 374 #undef CONFIG_EEPRO100
 375 #undef CONFIG_TULIP
 376
 377 /************************************************************
 378  * USB support
 379  ************************************************************/
 380 #define CONFIG_PCI_OHCI                 1
 381 #define CONFIG_USB_OHCI_NEW             1
 382 #define CONFIG_USB_KEYBOARD             1
 383 #define CONFIG_SYS_STDIO_DEREGISTER
 384 #define CONFIG_SYS_USB_EVENT_POLL               1
 385 #define CONFIG_SYS_USB_OHCI_SLOT_NAME           "ohci_pci"
 386 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS      15
 387 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
 388
 389 /*PCIE video card used*/
 390 #define VIDEO_IO_OFFSET         CONFIG_SYS_PCIE2_IO_VIRT
 391
 392 /*PCI video card used*/
 393 /*#define VIDEO_IO_OFFSET       CONFIG_SYS_PCIE1_IO_VIRT*/
 394
 395 /* video */
 396 #define CONFIG_VIDEO
 397
 398 #if defined(CONFIG_VIDEO)
 399 #define CONFIG_BIOSEMU
 400 #define CONFIG_CFB_CONSOLE
 401 #define CONFIG_VIDEO_SW_CURSOR
 402 #define CONFIG_VGA_AS_SINGLE_DEVICE
 403 #define CONFIG_ATI_RADEON_FB
 404 #define CONFIG_VIDEO_LOGO
 405 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT
 406 #endif
 407
 408 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 409
 410 #define CONFIG_DOS_PARTITION
 411 #define CONFIG_SCSI_AHCI
 412
 413 #ifdef CONFIG_SCSI_AHCI
 414 #define CONFIG_LIBATA
 415 #define CONFIG_SATA_ULI5288
 416 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     4
 417 #define CONFIG_SYS_SCSI_MAX_LUN 1
 418 #define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
 419 #define CONFIG_SYS_SCSI_MAXDEVICE       CONFIG_SYS_SCSI_MAX_DEVICE
 420 #endif
 421
 422 #endif  /* CONFIG_PCI */
 423
 424 #if defined(CONFIG_TSEC_ENET)
 425
 426 #define CONFIG_MII              1       /* MII PHY management */
 427
 428 #define CONFIG_TSEC1            1
 429 #define CONFIG_TSEC1_NAME       "eTSEC1"
 430 #define CONFIG_TSEC2            1
 431 #define CONFIG_TSEC2_NAME       "eTSEC2"
 432 #define CONFIG_TSEC3            1
 433 #define CONFIG_TSEC3_NAME       "eTSEC3"
 434 #define CONFIG_TSEC4            1
 435 #define CONFIG_TSEC4_NAME       "eTSEC4"
 436
 437 #define TSEC1_PHY_ADDR          0
 438 #define TSEC2_PHY_ADDR          1
 439 #define TSEC3_PHY_ADDR          2
 440 #define TSEC4_PHY_ADDR          3
 441 #define TSEC1_PHYIDX            0
 442 #define TSEC2_PHYIDX            0
 443 #define TSEC3_PHYIDX            0
 444 #define TSEC4_PHYIDX            0
 445 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 446 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 447 #define TSEC3_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 448 #define TSEC4_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 449
 450 #define CONFIG_ETHPRIME         "eTSEC1"
 451
 452 #endif  /* CONFIG_TSEC_ENET */
 453
 454
 455 #ifdef CONFIG_PHYS_64BIT
 456 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8)
 457 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2)
 458
 459 /* Put physical address into the BAT format */
 460 #define BAT_PHYS_ADDR(low, high) \
 461         (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high))
 462 /* Convert high/low pairs to actual 64-bit value */
 463 #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32))
 464 #else
 465 /* 32-bit systems just ignore the "high" bits */
 466 #define BAT_PHYS_ADDR(low, high)        (low)
 467 #define PAIRED_PHYS_TO_PHYS(low, high)  (low)
 468 #endif
 469
 470 /*
 471  * BAT0         DDR
 472  */
 473 #define CONFIG_SYS_DBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 474 #define CONFIG_SYS_IBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 475
 476 /*
 477  * BAT1         LBC (PIXIS/CF)
 478  */
 479 #define CONFIG_SYS_DBAT1L       (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \
 480                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 481                                  | BATL_PP_RW | BATL_CACHEINHIBIT | \
 482                                  BATL_GUARDEDSTORAGE)
 483 #define CONFIG_SYS_DBAT1U       (CONFIG_SYS_LBC_BASE | BATU_BL_128K \
 484                                  | BATU_VS | BATU_VP)
 485 #define CONFIG_SYS_IBAT1L       (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \
 486                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 487                                  | BATL_PP_RW | BATL_MEMCOHERENCE)
 488 #define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U
 489
 490 /* if CONFIG_PCI:
 491  * BAT2         PCIE1 and PCIE1 MEM
 492  * if CONFIG_RIO
 493  * BAT2         Rapidio Memory
 494  */
 495 #ifdef CONFIG_PCI
 496 #define CONFIG_PCI_INDIRECT_BRIDGE
 497 #define CONFIG_SYS_DBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 498                                                CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \
 499                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 500                                  | BATL_GUARDEDSTORAGE)
 501 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \
 502                                  | BATU_VS | BATU_VP)
 503 #define CONFIG_SYS_IBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 504                                                CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \
 505                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 506 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 507 #else /* CONFIG_RIO */
 508 #define CONFIG_SYS_DBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 509                                                CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \
 510                                  | BATL_PP_RW | BATL_CACHEINHIBIT | \
 511                                  BATL_GUARDEDSTORAGE)
 512 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \
 513                                  | BATU_VS | BATU_VP)
 514 #define CONFIG_SYS_IBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 515                                                CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \
 516                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 517 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 518 #endif
 519
 520 /*
 521  * BAT3         CCSR Space
 522  */
 523 #define CONFIG_SYS_DBAT3L       (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 524                                                CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
 525                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 526                                  | BATL_GUARDEDSTORAGE)
 527 #define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \
 528                                  | BATU_VP)
 529 #define CONFIG_SYS_IBAT3L       (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 530                                                CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
 531                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 532 #define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U
 533
 534 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 535 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 536                                        | BATL_PP_RW | BATL_CACHEINHIBIT \
 537                                        | BATL_GUARDEDSTORAGE)
 538 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
 539                                        | BATU_BL_1M | BATU_VS | BATU_VP)
 540 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 541                                        | BATL_PP_RW | BATL_CACHEINHIBIT)
 542 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
 543 #endif
 544
 545 /*
 546  * BAT4         PCIE1_IO and PCIE2_IO
 547  */
 548 #define CONFIG_SYS_DBAT4L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 549                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 550                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 551                                  | BATL_GUARDEDSTORAGE)
 552 #define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \
 553                                  | BATU_VS | BATU_VP)
 554 #define CONFIG_SYS_IBAT4L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 555                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 556                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 557 #define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U
 558
 559 /*
 560  * BAT5         Init RAM for stack in the CPU DCache (no backing memory)
 561  */
 562 #define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
 563 #define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 564 #define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
 565 #define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U
 566
 567 /*
 568  * BAT6         FLASH
 569  */
 570 #define CONFIG_SYS_DBAT6L       (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 571                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 572                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 573                                  | BATL_GUARDEDSTORAGE)
 574 #define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \
 575                                  | BATU_VP)
 576 #define CONFIG_SYS_IBAT6L       (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 577                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 578                                  | BATL_PP_RW | BATL_MEMCOHERENCE)
 579 #define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U
 580
 581 /* Map the last 1M of flash where we're running from reset */
 582 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 583                                  | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 584 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
 585 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 586                                  | BATL_MEMCOHERENCE)
 587 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
 588
 589 /*
 590  * BAT7         FREE - used later for tmp mappings
 591  */
 592 #define CONFIG_SYS_DBAT7L 0x00000000
 593 #define CONFIG_SYS_DBAT7U 0x00000000
 594 #define CONFIG_SYS_IBAT7L 0x00000000
 595 #define CONFIG_SYS_IBAT7U 0x00000000
 596
 597 /*
 598  * Environment
 599  */
 600 #ifndef CONFIG_SYS_RAMBOOT
 601     #define CONFIG_ENV_IS_IN_FLASH      1
 602     #define CONFIG_ENV_ADDR             \
 603                         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 604     #define CONFIG_ENV_SECT_SIZE                0x10000 /* 64K(one sector) for env */
 605 #else
 606     #define CONFIG_ENV_IS_NOWHERE       1       /* Store ENV in memory only */
 607     #define CONFIG_ENV_ADDR             (CONFIG_SYS_MONITOR_BASE - 0x1000)
 608 #endif
 609 #define CONFIG_ENV_SIZE         0x2000
 610
 611 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 612 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 613
 614
 615 /*
 616  * BOOTP options
 617  */
 618 #define CONFIG_BOOTP_BOOTFILESIZE
 619 #define CONFIG_BOOTP_BOOTPATH
 620 #define CONFIG_BOOTP_GATEWAY
 621 #define CONFIG_BOOTP_HOSTNAME
 622
 623
 624 /*
 625  * Command line configuration.
 626  */
 627 #define CONFIG_CMD_PING
 628 #define CONFIG_CMD_I2C
 629 #define CONFIG_CMD_REGINFO
 630
 631 #if defined(CONFIG_PCI)
 632     #define CONFIG_CMD_PCI
 633     #define CONFIG_CMD_SCSI
 634     #define CONFIG_CMD_EXT2
 635     #define CONFIG_CMD_USB
 636 #endif
 637
 638
 639 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 640
 641 /*
 642  * Miscellaneous configurable options
 643  */
 644 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 645 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 646 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 647
 648 #if defined(CONFIG_CMD_KGDB)
 649     #define CONFIG_SYS_CBSIZE   1024            /* Console I/O Buffer Size */
 650 #else
 651     #define CONFIG_SYS_CBSIZE   256             /* Console I/O Buffer Size */
 652 #endif
 653
 654 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 655 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 656 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 657
 658 /*
 659  * For booting Linux, the board info and command line data
 660  * have to be in the first 8 MB of memory, since this is
 661  * the maximum mapped by the Linux kernel during initialization.
 662  */
 663 #define CONFIG_SYS_BOOTMAPSZ    (8 << 20)       /* Initial Memory map for Linux*/
 664
 665 #if defined(CONFIG_CMD_KGDB)
 666     #define CONFIG_KGDB_BAUDRATE        230400  /* speed to run kgdb serial port */
 667 #endif
 668
 669 /*
 670  * Environment Configuration
 671  */
 672
 673 #define CONFIG_HAS_ETH0         1
 674 #define CONFIG_HAS_ETH1         1
 675 #define CONFIG_HAS_ETH2         1
 676 #define CONFIG_HAS_ETH3         1
 677
 678 #define CONFIG_IPADDR           192.168.1.100
 679
 680 #define CONFIG_HOSTNAME         unknown
 681 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 682 #define CONFIG_BOOTFILE         "uImage"
 683 #define CONFIG_UBOOTPATH        u-boot.bin      /* U-Boot image on TFTP server */
 684
 685 #define CONFIG_SERVERIP         192.168.1.1
 686 #define CONFIG_GATEWAYIP        192.168.1.1
 687 #define CONFIG_NETMASK          255.255.255.0
 688
 689 /* default location for tftp and bootm */
 690 #define CONFIG_LOADADDR         1000000
 691
 692 #define CONFIG_BOOTDELAY 10     /* -1 disables auto-boot */
 693 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */
 694
 695 #define CONFIG_BAUDRATE 115200
 696
 697 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 698         "netdev=eth0\0"                                                 \
 699         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
 700         "tftpflash=tftpboot $loadaddr $uboot; "                         \
 701                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 702                         " +$filesize; " \
 703                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 704                         " +$filesize; " \
 705                 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
 706                         " $filesize; "  \
 707                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 708                         " +$filesize; " \
 709                 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
 710                         " $filesize\0"  \
 711         "consoledev=ttyS0\0"                                            \
 712         "ramdiskaddr=2000000\0"                                         \
 713         "ramdiskfile=your.ramdisk.u-boot\0"                             \
 714         "fdtaddr=c00000\0"                                              \
 715         "fdtfile=mpc8641_hpcn.dtb\0"                                    \
 716         "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0"                        \
 717         "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \
 718         "maxcpus=2"
 719
 720
 721 #define CONFIG_NFSBOOTCOMMAND                                           \
 722         "setenv bootargs root=/dev/nfs rw "                             \
 723               "nfsroot=$serverip:$rootpath "                            \
 724               "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 725               "console=$consoledev,$baudrate $othbootargs;"             \
 726         "tftp $loadaddr $bootfile;"                                     \
 727         "tftp $fdtaddr $fdtfile;"                                       \
 728         "bootm $loadaddr - $fdtaddr"
 729
 730 #define CONFIG_RAMBOOTCOMMAND                                           \
 731         "setenv bootargs root=/dev/ram rw "                             \
 732               "console=$consoledev,$baudrate $othbootargs;"             \
 733         "tftp $ramdiskaddr $ramdiskfile;"                               \
 734         "tftp $loadaddr $bootfile;"                                     \
 735         "tftp $fdtaddr $fdtfile;"                                       \
 736         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 737
 738 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 739
 740 #endif  /* __CONFIG_H */