include/configs/MPC8569MDS.h

   1 /*
   2  * Copyright 2009-2011 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * mpc8569mds board configuration file
   9  */
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 /* High Level Configuration Options */
  14 #define CONFIG_BOOKE            1       /* BOOKE */
  15 #define CONFIG_E500             1       /* BOOKE e500 family */
  16
  17 #define CONFIG_FSL_ELBC         1       /* Has Enhance localbus controller */
  18
  19 #define CONFIG_SYS_SRIO
  20 #define CONFIG_SRIO1                    /* SRIO port 1 */
  21
  22 #define CONFIG_PCIE1            1       /* PCIE controller */
  23 #define CONFIG_FSL_PCI_INIT     1       /* use common fsl pci init code */
  24 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  25 #define CONFIG_FSL_PCIE_RESET   1       /* need PCIe reset errata */
  26 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  27 #define CONFIG_QE                       /* Enable QE */
  28 #define CONFIG_ENV_OVERWRITE
  29 #define CONFIG_FSL_LAW          1       /* Use common FSL init code */
  30
  31 #ifndef __ASSEMBLY__
  32 extern unsigned long get_clock_freq(void);
  33 #endif
  34 /* Replace a call to get_clock_freq (after it is implemented)*/
  35 #define CONFIG_SYS_CLK_FREQ     66666666
  36 #define CONFIG_DDR_CLK_FREQ     CONFIG_SYS_CLK_FREQ
  37
  38 #ifdef CONFIG_ATM
  39 #define CONFIG_PQ_MDS_PIB
  40 #define CONFIG_PQ_MDS_PIB_ATM
  41 #endif
  42
  43 /*
  44  * These can be toggled for performance analysis, otherwise use default.
  45  */
  46 #define CONFIG_L2_CACHE                         /* toggle L2 cache      */
  47 #define CONFIG_BTB                              /* toggle branch predition */
  48
  49 #ifndef CONFIG_SYS_TEXT_BASE
  50 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  51 #endif
  52
  53 #ifndef CONFIG_SYS_MONITOR_BASE
  54 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  55 #endif
  56
  57 /*
  58  * Only possible on E500 Version 2 or newer cores.
  59  */
  60 #define CONFIG_ENABLE_36BIT_PHYS        1
  61
  62 #define CONFIG_BOARD_EARLY_INIT_F       1       /* Call board_pre_init */
  63 #define CONFIG_BOARD_EARLY_INIT_R       1
  64 #define CONFIG_HWCONFIG
  65
  66 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
  67 #define CONFIG_SYS_MEMTEST_END          0x00400000
  68
  69 /*
  70  * Config the L2 Cache as L2 SRAM
  71  */
  72 #define CONFIG_SYS_INIT_L2_ADDR         0xf8f80000
  73 #define CONFIG_SYS_INIT_L2_ADDR_PHYS    CONFIG_SYS_INIT_L2_ADDR
  74 #define CONFIG_SYS_L2_SIZE              (512 << 10)
  75 #define CONFIG_SYS_INIT_L2_END  (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
  76
  77 #define CONFIG_SYS_CCSRBAR              0xe0000000
  78 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  79
  80 #if defined(CONFIG_NAND_SPL)
  81 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  82 #endif
  83
  84 /* DDR Setup */
  85 #define CONFIG_SYS_FSL_DDR3
  86 #undef CONFIG_FSL_DDR_INTERACTIVE
  87 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup*/
  88 #define CONFIG_DDR_SPD
  89 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
  90
  91 #define CONFIG_MEM_INIT_VALUE   0xDeadBeef
  92
  93 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
  94                                         /* DDR is system memory*/
  95 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  96
  97 #define CONFIG_NUM_DDR_CONTROLLERS      1
  98 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  99 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 100
 101 /* I2C addresses of SPD EEPROMs */
 102 #define SPD_EEPROM_ADDRESS    0x51    /* CTLR 0 DIMM 0 */
 103
 104 /* These are used when DDR doesn't use SPD.  */
 105 #define CONFIG_SYS_SDRAM_SIZE           1024            /* DDR is 1024MB */
 106 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003F
 107 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014202
 108 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
 109 #define CONFIG_SYS_DDR_TIMING_0         0x00330004
 110 #define CONFIG_SYS_DDR_TIMING_1         0x6F6B4644
 111 #define CONFIG_SYS_DDR_TIMING_2         0x002888D0
 112 #define CONFIG_SYS_DDR_SDRAM_CFG        0x47000000
 113 #define CONFIG_SYS_DDR_SDRAM_CFG_2      0x04401040
 114 #define CONFIG_SYS_DDR_SDRAM_MODE       0x40401521
 115 #define CONFIG_SYS_DDR_SDRAM_MODE_2     0x8000C000
 116 #define CONFIG_SYS_DDR_SDRAM_INTERVAL   0x03E00000
 117 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 118 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   0x01000000
 119 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 120 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 121 #define CONFIG_SYS_DDR_ZQ_CNTL          0x89080600
 122 #define CONFIG_SYS_DDR_WRLVL_CNTL       0x0655A604
 123 #define CONFIG_SYS_DDR_CDR_1            0x80040000
 124 #define CONFIG_SYS_DDR_CDR_2            0x00000000
 125 #define CONFIG_SYS_DDR_OCD_CTRL         0x00000000
 126 #define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
 127 #define CONFIG_SYS_DDR_CONTROL          0xc7000000      /* Type = DDR3 */
 128 #define CONFIG_SYS_DDR_CONTROL2         0x24400000
 129
 130 #define CONFIG_SYS_DDR_ERR_INT_EN       0x0000000d
 131 #define CONFIG_SYS_DDR_ERR_DIS          0x00000000
 132 #define CONFIG_SYS_DDR_SBE              0x00010000
 133
 134 #undef CONFIG_CLOCKS_IN_MHZ
 135
 136 /*
 137  * Local Bus Definitions
 138  */
 139
 140 #define CONFIG_SYS_FLASH_BASE           0xfe000000      /* start of FLASH 32M */
 141 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 142
 143 #define CONFIG_SYS_BCSR_BASE            0xf8000000
 144 #define CONFIG_SYS_BCSR_BASE_PHYS       CONFIG_SYS_BCSR_BASE
 145
 146 /*Chip select 0 - Flash*/
 147 #define CONFIG_FLASH_BR_PRELIM          0xfe000801
 148 #define CONFIG_FLASH_OR_PRELIM          0xfe000ff7
 149
 150 /*Chip select 1 - BCSR*/
 151 #define CONFIG_SYS_BR1_PRELIM           0xf8000801
 152 #define CONFIG_SYS_OR1_PRELIM           0xffffe9f7
 153
 154 /*Chip select 4 - PIB*/
 155 #define CONFIG_SYS_BR4_PRELIM           0xf8008801
 156 #define CONFIG_SYS_OR4_PRELIM           0xffffe9f7
 157
 158 /*Chip select 5 - PIB*/
 159 #define CONFIG_SYS_BR5_PRELIM           0xf8010801
 160 #define CONFIG_SYS_OR5_PRELIM           0xffffe9f7
 161
 162 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 163 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* sectors per device */
 164 #undef  CONFIG_SYS_FLASH_CHECKSUM
 165 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 166 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 167
 168 #undef CONFIG_SYS_RAMBOOT
 169
 170 #define CONFIG_FLASH_CFI_DRIVER
 171 #define CONFIG_SYS_FLASH_CFI
 172 #define CONFIG_SYS_FLASH_EMPTY_INFO
 173
 174 /* Chip select 3 - NAND */
 175 #ifndef CONFIG_NAND_SPL
 176 #define CONFIG_SYS_NAND_BASE            0xFC000000
 177 #else
 178 #define CONFIG_SYS_NAND_BASE            0xFFF00000
 179 #endif
 180
 181 /* NAND boot: 4K NAND loader config */
 182 #define CONFIG_SYS_NAND_SPL_SIZE        0x1000
 183 #define CONFIG_SYS_NAND_U_BOOT_SIZE     ((512 << 10) - 0x2000)
 184 #define CONFIG_SYS_NAND_U_BOOT_DST      (CONFIG_SYS_INIT_L2_ADDR)
 185 #define CONFIG_SYS_NAND_U_BOOT_START \
 186         (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
 187 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (0)
 188 #define CONFIG_SYS_NAND_U_BOOT_RELOC    (CONFIG_SYS_INIT_L2_END - 0x2000)
 189 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
 190
 191 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
 192 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE, }
 193 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 194 #define CONFIG_CMD_NAND                 1
 195 #define CONFIG_NAND_FSL_ELBC            1
 196 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 197 #define CONFIG_SYS_NAND_BR_PRELIM       (CONFIG_SYS_NAND_BASE_PHYS \
 198                                 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
 199                                 | BR_PS_8            /* Port Size = 8 bit */ \
 200                                 | BR_MS_FCM          /* MSEL = FCM */ \
 201                                 | BR_V)              /* valid */
 202 #define CONFIG_SYS_NAND_OR_PRELIM       (0xFFFC0000          /* length 256K */ \
 203                                 | OR_FCM_CSCT \
 204                                 | OR_FCM_CST \
 205                                 | OR_FCM_CHT \
 206                                 | OR_FCM_SCY_1 \
 207                                 | OR_FCM_TRLX \
 208                                 | OR_FCM_EHTR)
 209
 210 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 211 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 212 #define CONFIG_SYS_BR3_PRELIM   CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 213 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 214
 215 #define CONFIG_SYS_LBC_LCRR     0x00000004      /* LB clock ratio reg */
 216 #define CONFIG_SYS_LBC_LBCR     0x00040000      /* LB config reg */
 217 #define CONFIG_SYS_LBC_LSRT     0x20000000      /* LB sdram refresh timer */
 218 #define CONFIG_SYS_LBC_MRTPR    0x00000000      /* LB refresh timer prescal*/
 219
 220 #define CONFIG_SYS_INIT_RAM_LOCK        1
 221 #define CONFIG_SYS_INIT_RAM_ADDR        0xe4010000  /* Initial RAM address */
 222 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000      /* Size of used area in RAM */
 223
 224 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 225                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 226 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 227
 228 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)    /* Reserve 256 kB for Mon */
 229 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024)    /* Reserved for malloc */
 230
 231 /* Serial Port */
 232 #define CONFIG_CONS_INDEX               1
 233 #define CONFIG_SYS_NS16550_SERIAL
 234 #define CONFIG_SYS_NS16550_REG_SIZE    1
 235 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 236 #ifdef CONFIG_NAND_SPL
 237 #define CONFIG_NS16550_MIN_FUNCTIONS
 238 #endif
 239
 240 #define CONFIG_SYS_BAUDRATE_TABLE  \
 241         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 242
 243 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
 244 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 245
 246 /*
 247  * I2C
 248  */
 249 #define CONFIG_SYS_I2C
 250 #define CONFIG_SYS_I2C_FSL
 251 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 252 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 253 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 254 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 255 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 256 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 257 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 258
 259 /*
 260  * I2C2 EEPROM
 261  */
 262 #define CONFIG_ID_EEPROM
 263 #ifdef CONFIG_ID_EEPROM
 264 #define CONFIG_SYS_I2C_EEPROM_NXID
 265 #endif
 266 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x52
 267 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 268 #define CONFIG_SYS_EEPROM_BUS_NUM       1
 269
 270 #define PLPPAR1_I2C_BIT_MASK            0x0000000F
 271 #define PLPPAR1_I2C2_VAL                0x00000000
 272 #define PLPPAR1_ESDHC_VAL               0x0000000A
 273 #define PLPDIR1_I2C_BIT_MASK            0x0000000F
 274 #define PLPDIR1_I2C2_VAL                0x0000000F
 275 #define PLPDIR1_ESDHC_VAL               0x00000006
 276 #define PLPPAR1_UART0_BIT_MASK          0x00000fc0
 277 #define PLPPAR1_ESDHC_4BITS_VAL         0x00000a80
 278 #define PLPDIR1_UART0_BIT_MASK          0x00000fc0
 279 #define PLPDIR1_ESDHC_4BITS_VAL         0x00000a80
 280
 281 /*
 282  * General PCI
 283  * Memory Addresses are mapped 1-1. I/O is mapped from 0
 284  */
 285 #define CONFIG_SYS_PCIE1_NAME           "Slot"
 286 #define CONFIG_SYS_PCIE1_MEM_VIRT       0xa0000000
 287 #define CONFIG_SYS_PCIE1_MEM_BUS        0xa0000000
 288 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xa0000000
 289 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 290 #define CONFIG_SYS_PCIE1_IO_VIRT        0xe2800000
 291 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 292 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe2800000
 293 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 294
 295 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xC0000000
 296 #define CONFIG_SYS_SRIO1_MEM_BUS        0xC0000000
 297 #define CONFIG_SYS_SRIO1_MEM_PHYS       CONFIG_SYS_SRIO1_MEM_BUS
 298 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x20000000      /* 512M */
 299
 300 #ifdef CONFIG_QE
 301 /*
 302  * QE UEC ethernet configuration
 303  */
 304 #define CONFIG_SYS_UCC_RGMII_MODE       /* Set UCC work at RGMII by default */
 305 #undef CONFIG_SYS_UCC_RMII_MODE         /* Set UCC work at RMII mode */
 306
 307 #define CONFIG_MIIM_ADDRESS     (CONFIG_SYS_CCSRBAR + 0x82120)
 308 #define CONFIG_UEC_ETH
 309 #define CONFIG_ETHPRIME         "UEC0"
 310 #define CONFIG_PHY_MODE_NEED_CHANGE
 311
 312 #define CONFIG_UEC_ETH1         /* GETH1 */
 313 #define CONFIG_HAS_ETH0
 314
 315 #ifdef CONFIG_UEC_ETH1
 316 #define CONFIG_SYS_UEC1_UCC_NUM        0       /* UCC1 */
 317 #define CONFIG_SYS_UEC1_RX_CLK         QE_CLK_NONE
 318 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 319 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK12
 320 #define CONFIG_SYS_UEC1_ETH_TYPE       GIGA_ETH
 321 #define CONFIG_SYS_UEC1_PHY_ADDR       7
 322 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 323 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 324 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 325 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK16 /* CLK16 for RMII */
 326 #define CONFIG_SYS_UEC1_ETH_TYPE       FAST_ETH
 327 #define CONFIG_SYS_UEC1_PHY_ADDR       8        /* 0x8 for RMII */
 328 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 329 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
 330 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 331 #endif /* CONFIG_UEC_ETH1 */
 332
 333 #define CONFIG_UEC_ETH2         /* GETH2 */
 334 #define CONFIG_HAS_ETH1
 335
 336 #ifdef CONFIG_UEC_ETH2
 337 #define CONFIG_SYS_UEC2_UCC_NUM        1       /* UCC2 */
 338 #define CONFIG_SYS_UEC2_RX_CLK         QE_CLK_NONE
 339 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 340 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK17
 341 #define CONFIG_SYS_UEC2_ETH_TYPE       GIGA_ETH
 342 #define CONFIG_SYS_UEC2_PHY_ADDR       1
 343 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 344 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 345 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 346 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK16 /* CLK 16 for RMII */
 347 #define CONFIG_SYS_UEC2_ETH_TYPE       FAST_ETH
 348 #define CONFIG_SYS_UEC2_PHY_ADDR       0x9      /* 0x9 for RMII */
 349 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 350 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
 351 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 352 #endif /* CONFIG_UEC_ETH2 */
 353
 354 #define CONFIG_UEC_ETH3         /* GETH3 */
 355 #define CONFIG_HAS_ETH2
 356
 357 #ifdef CONFIG_UEC_ETH3
 358 #define CONFIG_SYS_UEC3_UCC_NUM        2       /* UCC3 */
 359 #define CONFIG_SYS_UEC3_RX_CLK         QE_CLK_NONE
 360 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 361 #define CONFIG_SYS_UEC3_TX_CLK         QE_CLK12
 362 #define CONFIG_SYS_UEC3_ETH_TYPE       GIGA_ETH
 363 #define CONFIG_SYS_UEC3_PHY_ADDR       2
 364 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 365 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000
 366 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 367 #define CONFIG_SYS_UEC3_TX_CLK          QE_CLK16 /* CLK_16 for RMII */
 368 #define CONFIG_SYS_UEC3_ETH_TYPE        FAST_ETH
 369 #define CONFIG_SYS_UEC3_PHY_ADDR        0xA     /* 0xA for RMII */
 370 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 371 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 100
 372 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 373 #endif /* CONFIG_UEC_ETH3 */
 374
 375 #define CONFIG_UEC_ETH4         /* GETH4 */
 376 #define CONFIG_HAS_ETH3
 377
 378 #ifdef CONFIG_UEC_ETH4
 379 #define CONFIG_SYS_UEC4_UCC_NUM        3       /* UCC4 */
 380 #define CONFIG_SYS_UEC4_RX_CLK         QE_CLK_NONE
 381 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 382 #define CONFIG_SYS_UEC4_TX_CLK         QE_CLK17
 383 #define CONFIG_SYS_UEC4_ETH_TYPE       GIGA_ETH
 384 #define CONFIG_SYS_UEC4_PHY_ADDR       3
 385 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 386 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000
 387 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 388 #define CONFIG_SYS_UEC4_TX_CLK          QE_CLK16 /* CLK16 for RMII */
 389 #define CONFIG_SYS_UEC4_ETH_TYPE        FAST_ETH
 390 #define CONFIG_SYS_UEC4_PHY_ADDR        0xB     /* 0xB for RMII */
 391 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 392 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 100
 393 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 394 #endif /* CONFIG_UEC_ETH4 */
 395
 396 #undef CONFIG_UEC_ETH6         /* GETH6 */
 397 #define CONFIG_HAS_ETH5
 398
 399 #ifdef CONFIG_UEC_ETH6
 400 #define CONFIG_SYS_UEC6_UCC_NUM        5       /* UCC6 */
 401 #define CONFIG_SYS_UEC6_RX_CLK         QE_CLK_NONE
 402 #define CONFIG_SYS_UEC6_TX_CLK         QE_CLK_NONE
 403 #define CONFIG_SYS_UEC6_ETH_TYPE       GIGA_ETH
 404 #define CONFIG_SYS_UEC6_PHY_ADDR       4
 405 #define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
 406 #define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000
 407 #endif /* CONFIG_UEC_ETH6 */
 408
 409 #undef CONFIG_UEC_ETH8         /* GETH8 */
 410 #define CONFIG_HAS_ETH7
 411
 412 #ifdef CONFIG_UEC_ETH8
 413 #define CONFIG_SYS_UEC8_UCC_NUM        7       /* UCC8 */
 414 #define CONFIG_SYS_UEC8_RX_CLK         QE_CLK_NONE
 415 #define CONFIG_SYS_UEC8_TX_CLK         QE_CLK_NONE
 416 #define CONFIG_SYS_UEC8_ETH_TYPE       GIGA_ETH
 417 #define CONFIG_SYS_UEC8_PHY_ADDR       6
 418 #define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
 419 #define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000
 420 #endif /* CONFIG_UEC_ETH8 */
 421
 422 #endif /* CONFIG_QE */
 423
 424 #if defined(CONFIG_PCI)
 425 #undef CONFIG_EEPRO100
 426 #undef CONFIG_TULIP
 427
 428 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 429
 430 #endif  /* CONFIG_PCI */
 431
 432 /*
 433  * Environment
 434  */
 435 #if defined(CONFIG_SYS_RAMBOOT)
 436 #else
 437 #define CONFIG_ENV_IS_IN_FLASH  1
 438 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 439 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 440 #define CONFIG_ENV_SIZE         0x2000
 441 #endif
 442
 443 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 444 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 445
 446 /* QE microcode/firmware address */
 447 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 448 #define CONFIG_SYS_QE_FW_ADDR   0xfff00000
 449
 450 /*
 451  * BOOTP options
 452  */
 453 #define CONFIG_BOOTP_BOOTFILESIZE
 454 #define CONFIG_BOOTP_BOOTPATH
 455 #define CONFIG_BOOTP_GATEWAY
 456 #define CONFIG_BOOTP_HOSTNAME
 457
 458 /*
 459  * Command line configuration.
 460  */
 461 #define CONFIG_CMD_IRQ
 462 #define CONFIG_CMD_REGINFO
 463
 464 #if defined(CONFIG_PCI)
 465     #define CONFIG_CMD_PCI
 466 #endif
 467
 468 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 469
 470 #define CONFIG_MMC     1
 471
 472 #ifdef CONFIG_MMC
 473 #define CONFIG_FSL_ESDHC
 474 #define CONFIG_FSL_ESDHC_PIN_MUX
 475 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 476 #define CONFIG_GENERIC_MMC
 477 #define CONFIG_DOS_PARTITION
 478 #endif
 479
 480 /*
 481  * Miscellaneous configurable options
 482  */
 483 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 484 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 485 #define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
 486 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 487 #if defined(CONFIG_CMD_KGDB)
 488 #define CONFIG_SYS_CBSIZE       2048            /* Console I/O Buffer Size */
 489 #else
 490 #define CONFIG_SYS_CBSIZE       512             /* Console I/O Buffer Size */
 491 #endif
 492 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 493                                                 /* Print Buffer Size */
 494 #define CONFIG_SYS_MAXARGS      32              /* max number of command args */
 495 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 496                                                 /* Boot Argument Buffer Size */
 497
 498 /*
 499  * For booting Linux, the board info and command line data
 500  * have to be in the first 64 MB of memory, since this is
 501  * the maximum mapped by the Linux kernel during initialization.
 502  */
 503 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20) /* Initial Memory map for Linux*/
 504 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 505
 506 #if defined(CONFIG_CMD_KGDB)
 507 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 508 #endif
 509
 510 /*
 511  * Environment Configuration
 512  */
 513 #define CONFIG_HOSTNAME mpc8569mds
 514 #define CONFIG_ROOTPATH  "/nfsroot"
 515 #define CONFIG_BOOTFILE  "your.uImage"
 516
 517 #define CONFIG_SERVERIP  192.168.1.1
 518 #define CONFIG_GATEWAYIP 192.168.1.1
 519 #define CONFIG_NETMASK   255.255.255.0
 520
 521 #define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
 522
 523 #undef  CONFIG_BOOTARGS           /* the boot command will set bootargs*/
 524
 525 #define CONFIG_BAUDRATE 115200
 526
 527 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 528         "netdev=eth0\0"                                                 \
 529         "consoledev=ttyS0\0"                                            \
 530         "ramdiskaddr=600000\0"                                          \
 531         "ramdiskfile=your.ramdisk.u-boot\0"                             \
 532         "fdtaddr=400000\0"                                              \
 533         "fdtfile=your.fdt.dtb\0"                                        \
 534         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 535         "nfsroot=$serverip:$rootpath "                                  \
 536         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 537         "console=$consoledev,$baudrate $othbootargs\0"                  \
 538         "ramargs=setenv bootargs root=/dev/ram rw "                     \
 539         "console=$consoledev,$baudrate $othbootargs\0"                  \
 540
 541 #define CONFIG_NFSBOOTCOMMAND                                           \
 542         "run nfsargs;"                                                  \
 543         "tftp $loadaddr $bootfile;"                                     \
 544         "tftp $fdtaddr $fdtfile;"                                       \
 545         "bootm $loadaddr - $fdtaddr"
 546
 547 #define CONFIG_RAMBOOTCOMMAND                                           \
 548         "run ramargs;"                                                  \
 549         "tftp $ramdiskaddr $ramdiskfile;"                               \
 550         "tftp $loadaddr $bootfile;"                                     \
 551         "bootm $loadaddr $ramdiskaddr"
 552
 553 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 554
 555 #endif  /* __CONFIG_H */