1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright 2004, 2007, 2010-2011 Freescale Semiconductor.
8 * mpc8548cds board configuration file
10 * Please refer to doc/README.mpc85xxcds for more info.
16 #define CONFIG_SYS_SRIO
17 #define CONFIG_SRIO1 /* SRIO port 1 */
19 #define CONFIG_PCI1 /* PCI controller 1 */
20 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
23 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
26 #include <linux/stringify.h>
30 * These can be toggled for performance analysis, otherwise use default.
32 #define CONFIG_L2_CACHE /* toggle L2 cache */
35 * Only possible on E500 Version 2 or newer cores.
38 #define CONFIG_SYS_CCSRBAR 0xe0000000
39 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
42 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
44 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef
46 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
47 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
49 /* I2C addresses of SPD EEPROMs */
50 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
52 /* Make sure required options are set */
53 #ifndef CONFIG_SPD_EEPROM
54 #error ("CONFIG_SPD_EEPROM is required")
58 * Physical Address Map
61 * 0x0000_0000 0x7fff_ffff DDR 2G cacheable
62 * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M cacheable
63 * 0xa000_0000 0xbfff_ffff PCIe MEM 512M cacheable
64 * 0xc000_0000 0xdfff_ffff RapidIO 512M cacheable
65 * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable
66 * 0xe200_0000 0xe20f_ffff PCI1 IO 1M non-cacheable
67 * 0xe300_0000 0xe30f_ffff PCIe IO 1M non-cacheable
68 * 0xf000_0000 0xf3ff_ffff SDRAM 64M cacheable
69 * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS 1M non-cacheable
70 * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable
71 * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable
74 * 0x00000_0000 0x07fff_ffff DDR 2G cacheable
75 * 0xc0000_0000 0xc1fff_ffff PCI1 MEM 512M cacheable
76 * 0xc2000_0000 0xc3fff_ffff PCIe MEM 512M cacheable
77 * 0xc4000_0000 0xc5fff_ffff RapidIO 512M cacheable
78 * 0xfe000_0000 0xfe00f_ffff CCSR 1M non-cacheable
79 * 0xfe200_0000 0xfe20f_ffff PCI1 IO 1M non-cacheable
80 * 0xfe300_0000 0xfe30f_ffff PCIe IO 1M non-cacheable
81 * 0xff000_0000 0xff3ff_ffff SDRAM 64M cacheable
82 * 0xff800_0000 0xff80f_ffff NVRAM/CADMUS 1M non-cacheable
83 * 0xfff00_0000 0xfff7f_ffff FLASH (2nd bank) 8M non-cacheable
84 * 0xfff80_0000 0xfffff_ffff FLASH (boot bank) 8M non-cacheable
89 * Local Bus Definitions
93 * FLASH on the Local Bus
94 * Two banks, 8M each, using the CFI driver.
95 * Boot from BR0/OR0 bank at 0xff00_0000
96 * Alternate BR1/OR1 bank at 0xff80_0000
99 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
100 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
101 * Port Size = 16 bits = BRx[19:20] = 10
102 * Use GPCM = BRx[24:26] = 000
103 * Valid = BRx[31] = 1
105 * 0 4 8 12 16 20 24 28
106 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
107 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
110 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
111 * Reserved ORx[17:18] = 11, confusion here?
113 * ACS = half cycle delay = ORx[21:22] = 11
114 * SCY = 6 = ORx[24:27] = 0110
115 * TRLX = use relaxed timing = ORx[29] = 1
116 * EAD = use external address latch delay = OR[31] = 1
118 * 0 4 8 12 16 20 24 28
119 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
122 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */
123 #ifdef CONFIG_PHYS_64BIT
124 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfff000000ull
126 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
129 #define CONFIG_SYS_FLASH_BANKS_LIST \
130 {CONFIG_SYS_FLASH_BASE_PHYS + 0x800000, CONFIG_SYS_FLASH_BASE_PHYS}
131 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
132 #undef CONFIG_SYS_FLASH_CHECKSUM
133 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
134 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
136 #define CONFIG_SYS_FLASH_EMPTY_INFO
138 #define CONFIG_HWCONFIG /* enable hwconfig */
141 * SDRAM on the Local Bus
143 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
144 #ifdef CONFIG_PHYS_64BIT
145 #define CONFIG_SYS_LBC_SDRAM_BASE_PHYS 0xff0000000ull
147 #define CONFIG_SYS_LBC_SDRAM_BASE_PHYS CONFIG_SYS_LBC_SDRAM_BASE
149 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
152 * Base Register 2 and Option Register 2 configure SDRAM.
153 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
156 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
157 * port-size = 32-bits = BR2[19:20] = 11
158 * no parity checking = BR2[21:22] = 00
159 * SDRAM for MSEL = BR2[24:26] = 011
162 * 0 4 8 12 16 20 24 28
163 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
165 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
166 * FIXME: the top 17 bits of BR2.
170 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
173 * 64MB mask for AM, OR2[0:7] = 1111 1100
174 * XAM, OR2[17:18] = 11
175 * 9 columns OR2[19-21] = 010
176 * 13 rows OR2[23-25] = 100
177 * EAD set for extra time OR[31] = 1
179 * 0 4 8 12 16 20 24 28
180 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
183 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
184 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
185 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
186 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
189 * Common settings for all Local Bus SDRAM commands.
190 * At run time, either BSMA1516 (for CPU 1.1)
191 * or BSMA1617 (for CPU 1.0) (old)
194 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \
204 * The CADMUS registers are connected to CS3 on CDS.
205 * The new memory map places CADMUS at 0xf8000000.
208 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
209 * port-size = 8-bits = BR[19:20] = 01
210 * no parity checking = BR[21:22] = 00
211 * GPMC for MSEL = BR[24:26] = 000
214 * 0 4 8 12 16 20 24 28
215 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
218 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
219 * disable buffer ctrl OR[19] = 0
223 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
227 * EAD extra time OR[31] = 1
229 * 0 4 8 12 16 20 24 28
230 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
233 #define CONFIG_FSL_CADMUS
235 #define CADMUS_BASE_ADDR 0xf8000000
236 #ifdef CONFIG_PHYS_64BIT
237 #define CADMUS_BASE_ADDR_PHYS 0xff8000000ull
239 #define CADMUS_BASE_ADDR_PHYS CADMUS_BASE_ADDR
242 #define CONFIG_SYS_INIT_RAM_LOCK 1
243 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
244 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
246 #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
248 #define CONFIG_SYS_MONITOR_LEN (512 * 1024)
251 #define CONFIG_SYS_NS16550_SERIAL
252 #define CONFIG_SYS_NS16550_REG_SIZE 1
253 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
255 #define CONFIG_SYS_BAUDRATE_TABLE \
256 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
258 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
259 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
264 #if !CONFIG_IS_ENABLED(DM_I2C)
265 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
269 #define CONFIG_SYS_I2C_EEPROM_CCID
273 * Memory space is mapped 1-1, but I/O space must start from 0.
275 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
276 #ifdef CONFIG_PHYS_64BIT
277 #define CONFIG_SYS_PCI1_MEM_BUS 0xe0000000
278 #define CONFIG_SYS_PCI1_MEM_PHYS 0xc00000000ull
280 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
281 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000
283 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
284 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
285 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000
286 #ifdef CONFIG_PHYS_64BIT
287 #define CONFIG_SYS_PCI1_IO_PHYS 0xfe2000000ull
289 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
291 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
294 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
295 #ifdef CONFIG_PHYS_64BIT
296 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc20000000ull
298 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
300 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe3000000
301 #ifdef CONFIG_PHYS_64BIT
302 #define CONFIG_SYS_PCIE1_IO_PHYS 0xfe3000000ull
304 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000
311 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xc0000000
312 #ifdef CONFIG_PHYS_64BIT
313 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc40000000ull
315 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc0000000
317 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */
319 #if defined(CONFIG_PCI)
320 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
321 #endif /* CONFIG_PCI */
323 #if defined(CONFIG_TSEC_ENET)
325 #define CONFIG_TSEC1 1
326 #define CONFIG_TSEC1_NAME "eTSEC0"
327 #define CONFIG_TSEC2 1
328 #define CONFIG_TSEC2_NAME "eTSEC1"
329 #define CONFIG_TSEC3 1
330 #define CONFIG_TSEC3_NAME "eTSEC2"
332 #define CONFIG_TSEC4_NAME "eTSEC3"
333 #undef CONFIG_MPC85XX_FEC
335 #define TSEC1_PHY_ADDR 0
336 #define TSEC2_PHY_ADDR 1
337 #define TSEC3_PHY_ADDR 2
338 #define TSEC4_PHY_ADDR 3
340 #define TSEC1_PHYIDX 0
341 #define TSEC2_PHYIDX 0
342 #define TSEC3_PHYIDX 0
343 #define TSEC4_PHYIDX 0
344 #define TSEC1_FLAGS TSEC_GIGABIT
345 #define TSEC2_FLAGS TSEC_GIGABIT
346 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
347 #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
348 #endif /* CONFIG_TSEC_ENET */
354 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
355 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
358 * Miscellaneous configurable options
362 * For booting Linux, the board info and command line data
363 * have to be in the first 64 MB of memory, since this is
364 * the maximum mapped by the Linux kernel during initialization.
366 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
367 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
370 * Environment Configuration
373 #define CONFIG_IPADDR 192.168.1.253
375 #define CONFIG_HOSTNAME "unknown"
376 #define CONFIG_ROOTPATH "/nfsroot"
377 #define CONFIG_UBOOTPATH 8548cds/u-boot.bin /* TFTP server */
379 #define CONFIG_SERVERIP 192.168.1.1
380 #define CONFIG_GATEWAYIP 192.168.1.1
381 #define CONFIG_NETMASK 255.255.255.0
383 #define CONFIG_EXTRA_ENV_SETTINGS \
384 "hwconfig=fsl_ddr:ecc=off\0" \
386 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
387 "tftpflash=tftpboot $loadaddr $uboot; " \
388 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
390 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
392 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
394 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
396 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
398 "consoledev=ttyS1\0" \
399 "ramdiskaddr=2000000\0" \
400 "ramdiskfile=ramdisk.uboot\0" \
401 "fdtaddr=1e00000\0" \
402 "fdtfile=mpc8548cds.dtb\0"
404 #endif /* __CONFIG_H */