2 * Copyright 2004 Freescale Semiconductor.
3 * (C) Copyright 2002,2003 Motorola,Inc.
4 * Xianghua Xiao <X.Xiao@motorola.com>
6 * See file CREDITS for list of people who contributed to this
9 * This program is free software; you can redistribute it and/or
10 * modify it under the terms of the GNU General Public License as
11 * published by the Free Software Foundation; either version 2 of
12 * the License, or (at your option) any later version.
14 * This program is distributed in the hope that it will be useful,
15 * but WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17 * GNU General Public License for more details.
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
26 * mpc8540ads board configuration file
28 * Please refer to doc/README.mpc85xx for more info.
30 * Make sure you change the MAC address and other network params first,
31 * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
37 /* High Level Configuration Options */
38 #define CONFIG_BOOKE 1 /* BOOKE */
39 #define CONFIG_E500 1 /* BOOKE e500 family */
40 #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
41 #define CONFIG_MPC8540 1 /* MPC8540 specific */
42 #define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific */
44 #ifndef CONFIG_HAS_FEC
45 #define CONFIG_HAS_FEC 1 /* 8540 has FEC */
49 #define CONFIG_TSEC_ENET /* tsec ethernet support */
50 #define CONFIG_ENV_OVERWRITE
51 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
52 #define CONFIG_DDR_DLL /* possible DLL fix needed */
53 #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
55 #define CONFIG_DDR_ECC /* only for ECC DDR module */
56 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef
58 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */
63 * Two valid values are:
67 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
68 * is likely the desired value here, so that is now the default.
69 * The board, however, can run at 66MHz. In any event, this value
70 * must match the settings of some switches. Details can be found
71 * in the README.mpc85xxads.
73 * XXX -- Can't we run at 66 MHz, anyway? PCI should drop to
74 * 33MHz to accommodate, based on a PCI pin.
75 * Note that PCI-X won't work at 33MHz.
78 #ifndef CONFIG_SYS_CLK_FREQ
79 #define CONFIG_SYS_CLK_FREQ 33000000
84 * These can be toggled for performance analysis, otherwise use default.
86 #define CONFIG_L2_CACHE /* toggle L2 cache */
87 #define CONFIG_BTB /* toggle branch predition */
88 #define CONFIG_ADDR_STREAMING /* toggle addr streaming */
90 #define CFG_MEMTEST_START 0x00200000 /* memtest region */
91 #define CFG_MEMTEST_END 0x00400000
95 * Base addresses -- Note these are effective addresses where the
96 * actual resources get mapped (not physical addresses)
98 #define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
99 #define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
100 #define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
101 #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
107 #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
108 #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
110 #if defined(CONFIG_SPD_EEPROM)
112 * Determine DDR configuration from I2C interface.
114 #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
118 * Manually set up DDR parameters
120 #define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
121 #define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
122 #define CFG_DDR_CS0_CONFIG 0x80000002
123 #define CFG_DDR_TIMING_1 0x37344321
124 #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
125 #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
126 #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
127 #define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
132 * SDRAM on the Local Bus
134 #define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
135 #define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
137 #define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
138 #define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
140 #define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
141 #define CFG_MAX_FLASH_BANKS 1 /* number of banks */
142 #define CFG_MAX_FLASH_SECT 64 /* sectors per device */
143 #undef CFG_FLASH_CHECKSUM
144 #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
145 #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
147 #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
149 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
155 #define CFG_FLASH_CFI_DRIVER
156 #define CFG_FLASH_CFI
157 #define CFG_FLASH_EMPTY_INFO
159 #undef CONFIG_CLOCKS_IN_MHZ
163 * Local Bus Definitions
167 * Base Register 2 and Option Register 2 configure SDRAM.
168 * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
171 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
172 * port-size = 32-bits = BR2[19:20] = 11
173 * no parity checking = BR2[21:22] = 00
174 * SDRAM for MSEL = BR2[24:26] = 011
177 * 0 4 8 12 16 20 24 28
178 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
180 * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
181 * FIXME: the top 17 bits of BR2.
184 #define CFG_BR2_PRELIM 0xf0001861
187 * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
190 * 64MB mask for AM, OR2[0:7] = 1111 1100
191 * XAM, OR2[17:18] = 11
192 * 9 columns OR2[19-21] = 010
193 * 13 rows OR2[23-25] = 100
194 * EAD set for extra time OR[31] = 1
196 * 0 4 8 12 16 20 24 28
197 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
200 #define CFG_OR2_PRELIM 0xfc006901
202 #define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
203 #define CFG_LBC_LBCR 0x00000000 /* LB config reg */
204 #define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
205 #define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
210 #define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
211 #define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
212 #define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
213 #define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
214 #define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
215 #define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
216 #define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
217 #define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
218 #define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
219 #define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
220 #define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
221 #define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
222 #define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
223 #define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
224 #define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
226 #define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
227 #define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
228 #define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
229 #define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
230 #define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
231 #define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
232 #define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
233 #define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
235 #define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_BSMA1516 \
236 | CFG_LBC_LSDMR_RFCR5 \
237 | CFG_LBC_LSDMR_PRETOACT3 \
238 | CFG_LBC_LSDMR_ACTTORW3 \
239 | CFG_LBC_LSDMR_BL8 \
240 | CFG_LBC_LSDMR_WRC2 \
241 | CFG_LBC_LSDMR_CL3 \
242 | CFG_LBC_LSDMR_RFEN \
246 * SDRAM Controller configuration sequence.
248 #define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
249 | CFG_LBC_LSDMR_OP_PCHALL)
250 #define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
251 | CFG_LBC_LSDMR_OP_ARFRSH)
252 #define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
253 | CFG_LBC_LSDMR_OP_ARFRSH)
254 #define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
255 | CFG_LBC_LSDMR_OP_MRW)
256 #define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
257 | CFG_LBC_LSDMR_OP_NORMAL)
261 * 32KB, 8-bit wide for ADS config reg
263 #define CFG_BR4_PRELIM 0xf8000801
264 #define CFG_OR4_PRELIM 0xffffe1f1
265 #define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
267 #define CONFIG_L1_INIT_RAM
268 #define CFG_INIT_RAM_LOCK 1
269 #define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
270 #define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
272 #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
273 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
274 #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
276 #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
277 #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
280 #define CONFIG_CONS_INDEX 1
281 #undef CONFIG_SERIAL_SOFTWARE_FIFO
283 #define CFG_NS16550_SERIAL
284 #define CFG_NS16550_REG_SIZE 1
285 #define CFG_NS16550_CLK get_bus_freq(0)
287 #define CFG_BAUDRATE_TABLE \
288 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
290 #define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
291 #define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
293 /* Use the HUSH parser */
294 #define CFG_HUSH_PARSER
295 #ifdef CFG_HUSH_PARSER
296 #define CFG_PROMPT_HUSH_PS2 "> "
299 /* pass open firmware flat tree */
300 #define CONFIG_OF_LIBFDT 1
301 #define CONFIG_OF_BOARD_SETUP 1
302 #define CONFIG_OF_STDOUT_VIA_ALIAS 1
304 #define CFG_64BIT_VSPRINTF 1
305 #define CFG_64BIT_STRTOUL 1
310 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */
311 #define CONFIG_HARD_I2C /* I2C with hardware support*/
312 #undef CONFIG_SOFT_I2C /* I2C bit-banged */
313 #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
314 #define CFG_I2C_SLAVE 0x7F
315 #define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
316 #define CFG_I2C_OFFSET 0x3000
319 #define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
320 #define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
321 #define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
325 * Memory space is mapped 1-1, but I/O space must start from 0.
327 #define CFG_PCI1_MEM_BASE 0x80000000
328 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
329 #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
330 #define CFG_PCI1_IO_BASE 0x00000000
331 #define CFG_PCI1_IO_PHYS 0xe2000000
332 #define CFG_PCI1_IO_SIZE 0x100000 /* 1M */
334 #if defined(CONFIG_PCI)
336 #define CONFIG_NET_MULTI
337 #define CONFIG_PCI_PNP /* do pci plug-and-play */
339 #undef CONFIG_EEPRO100
342 #if !defined(CONFIG_PCI_PNP)
343 #define PCI_ENET0_IOADDR 0xe0000000
344 #define PCI_ENET0_MEMADDR 0xe0000000
345 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
348 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
349 #define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
351 #endif /* CONFIG_PCI */
354 #if defined(CONFIG_TSEC_ENET)
356 #ifndef CONFIG_NET_MULTI
357 #define CONFIG_NET_MULTI 1
360 #define CONFIG_MII 1 /* MII PHY management */
361 #define CONFIG_TSEC1 1
362 #define CONFIG_TSEC1_NAME "TSEC0"
363 #define CONFIG_TSEC2 1
364 #define CONFIG_TSEC2_NAME "TSEC1"
365 #define TSEC1_PHY_ADDR 0
366 #define TSEC2_PHY_ADDR 1
367 #define TSEC1_PHYIDX 0
368 #define TSEC2_PHYIDX 0
369 #define TSEC1_FLAGS TSEC_GIGABIT
370 #define TSEC2_FLAGS TSEC_GIGABIT
374 #define CONFIG_MPC85XX_FEC 1
375 #define CONFIG_MPC85XX_FEC_NAME "FEC"
376 #define FEC_PHY_ADDR 3
381 /* Options are: TSEC[0-1], FEC */
382 #define CONFIG_ETHPRIME "TSEC0"
384 #endif /* CONFIG_TSEC_ENET */
391 #define CFG_ENV_IS_IN_FLASH 1
392 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
393 #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
394 #define CFG_ENV_SIZE 0x2000
396 #define CFG_NO_FLASH 1 /* Flash is not usable now */
397 #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
398 #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
399 #define CFG_ENV_SIZE 0x2000
402 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
403 #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
409 #define CONFIG_BOOTP_BOOTFILESIZE
410 #define CONFIG_BOOTP_BOOTPATH
411 #define CONFIG_BOOTP_GATEWAY
412 #define CONFIG_BOOTP_HOSTNAME
416 * Command line configuration.
418 #include <config_cmd_default.h>
420 #define CONFIG_CMD_PING
421 #define CONFIG_CMD_I2C
422 #define CONFIG_CMD_ELF
424 #if defined(CONFIG_PCI)
425 #define CONFIG_CMD_PCI
428 #if defined(CFG_RAMBOOT)
429 #undef CONFIG_CMD_ENV
430 #undef CONFIG_CMD_LOADS
434 #undef CONFIG_WATCHDOG /* watchdog disabled */
437 * Miscellaneous configurable options
439 #define CFG_LONGHELP /* undef to save memory */
440 #define CONFIG_CMDLINE_EDITING /* Command-line editing */
441 #define CFG_LOAD_ADDR 0x2000000 /* default load address */
442 #define CFG_PROMPT "=> " /* Monitor Command Prompt */
444 #if defined(CONFIG_CMD_KGDB)
445 #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
447 #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
450 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
451 #define CFG_MAXARGS 16 /* max number of command args */
452 #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
453 #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
456 * For booting Linux, the board info and command line data
457 * have to be in the first 8 MB of memory, since this is
458 * the maximum mapped by the Linux kernel during initialization.
460 #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
463 * Internal Definitions
467 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
468 #define BOOTFLAG_WARM 0x02 /* Software reboot */
470 #if defined(CONFIG_CMD_KGDB)
471 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
472 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
477 * Environment Configuration
480 /* The mac addresses for all ethernet interface */
481 #if defined(CONFIG_TSEC_ENET)
482 #define CONFIG_HAS_ETH0
483 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD
484 #define CONFIG_HAS_ETH1
485 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
486 #define CONFIG_HAS_ETH2
487 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
490 #define CONFIG_IPADDR 192.168.1.253
492 #define CONFIG_HOSTNAME unknown
493 #define CONFIG_ROOTPATH /nfsroot
494 #define CONFIG_BOOTFILE your.uImage
496 #define CONFIG_SERVERIP 192.168.1.1
497 #define CONFIG_GATEWAYIP 192.168.1.1
498 #define CONFIG_NETMASK 255.255.255.0
500 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
502 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
503 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
505 #define CONFIG_BAUDRATE 115200
507 #define CONFIG_EXTRA_ENV_SETTINGS \
509 "consoledev=ttyS0\0" \
510 "ramdiskaddr=1000000\0" \
511 "ramdiskfile=your.ramdisk.u-boot\0" \
513 "fdtfile=your.fdt.dtb\0"
515 #define CONFIG_NFSBOOTCOMMAND \
516 "setenv bootargs root=/dev/nfs rw " \
517 "nfsroot=$serverip:$rootpath " \
518 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
519 "console=$consoledev,$baudrate $othbootargs;" \
520 "tftp $loadaddr $bootfile;" \
521 "tftp $fdtaddr $fdtfile;" \
522 "bootm $loadaddr - $fdtaddr"
524 #define CONFIG_RAMBOOTCOMMAND \
525 "setenv bootargs root=/dev/ram rw " \
526 "console=$consoledev,$baudrate $othbootargs;" \
527 "tftp $ramdiskaddr $ramdiskfile;" \
528 "tftp $loadaddr $bootfile;" \
529 "tftp $fdtaddr $fdtfile;" \
530 "bootm $loadaddr $ramdiskaddr $fdtaddr"
532 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
534 #endif /* __CONFIG_H */