include/configs/MPC837XERDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2007 Freescale Semiconductor, Inc.
   4  * Kevin Lam <kevin.lam@freescale.com>
   5  * Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11 /*
  12  * High Level Configuration Options
  13  */
  14 #define CONFIG_E300             1 /* E300 family */
  15
  16 #define CONFIG_HWCONFIG
  17
  18 /*
  19  * On-board devices
  20  */
  21 #define CONFIG_VSC7385_ENET
  22
  23 /* System performance - define the value i.e. CONFIG_SYS_XXX
  24 */
  25
  26 /* System Clock Configuration Register */
  27 #define CONFIG_SYS_SCCR_TSEC1CM 1               /* eTSEC1 clock mode (0-3) */
  28 #define CONFIG_SYS_SCCR_TSEC2CM 1               /* eTSEC2 clock mode (0-3) */
  29 #define CONFIG_SYS_SCCR_SATACM  SCCR_SATACM_2   /* SATA1-4 clock mode (0-3) */
  30
  31 /*
  32  * System IO Config
  33  */
  34 #define CONFIG_SYS_SICRH                0x08200000
  35 #define CONFIG_SYS_SICRL                0x00000000
  36
  37 /*
  38  * Output Buffer Impedance
  39  */
  40 #define CONFIG_SYS_OBIR         0x30100000
  41
  42 /*
  43  * Device configurations
  44  */
  45
  46 /* Vitesse 7385 */
  47
  48 #ifdef CONFIG_VSC7385_ENET
  49
  50 #define CONFIG_TSEC2
  51
  52 /* The flash address and size of the VSC7385 firmware image */
  53 #define CONFIG_VSC7385_IMAGE            0xFE7FE000
  54 #define CONFIG_VSC7385_IMAGE_SIZE       8192
  55
  56 #endif
  57
  58 /*
  59  * DDR Setup
  60  */
  61 #define CONFIG_SYS_SDRAM_BASE           0x00000000 /* DDR is system memory */
  62 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   0x03000000
  63 #define CONFIG_SYS_83XX_DDR_USES_CS0
  64
  65 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN)
  66
  67 #undef CONFIG_DDR_ECC           /* support DDR ECC function */
  68 #undef CONFIG_DDR_ECC_CMD       /* Use DDR ECC user commands */
  69
  70 #undef CONFIG_NEVER_ASSERT_ODT_TO_CPU   /* Never assert ODT to internal IOs */
  71
  72 /*
  73  * Manually set up DDR parameters
  74  */
  75 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
  76 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000000f
  77 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
  78                                         | CSCONFIG_ODT_WR_ONLY_CURRENT \
  79                                         | CSCONFIG_ROW_BIT_13 \
  80                                         | CSCONFIG_COL_BIT_10)
  81
  82 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
  83 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
  84                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
  85                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
  86                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
  87                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
  88                                 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
  89                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
  90                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
  91                                 /* 0x00260802 */ /* DDR400 */
  92 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
  93                                 | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
  94                                 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
  95                                 | (7 << TIMING_CFG1_CASLAT_SHIFT) \
  96                                 | (13 << TIMING_CFG1_REFREC_SHIFT) \
  97                                 | (3 << TIMING_CFG1_WRREC_SHIFT) \
  98                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
  99                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 100                                 /* 0x3937d322 */
 101 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
 102                                 | (5 << TIMING_CFG2_CPO_SHIFT) \
 103                                 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 104                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 105                                 | (3 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 106                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 107                                 | (8 << TIMING_CFG2_FOUR_ACT_SHIFT))
 108                                 /* 0x02984cc8 */
 109
 110 #define CONFIG_SYS_DDR_INTERVAL ((1024 << SDRAM_INTERVAL_REFINT_SHIFT) \
 111                                 | (0 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 112                                 /* 0x06090100 */
 113
 114 #if defined(CONFIG_DDR_2T_TIMING)
 115 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 116                                         | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 117                                         | SDRAM_CFG_32_BE \
 118                                         | SDRAM_CFG_2T_EN)
 119                                         /* 0x43088000 */
 120 #else
 121 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 122                                         | SDRAM_CFG_SDRAM_TYPE_DDR2)
 123                                         /* 0x43000000 */
 124 #endif
 125 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00001000 /* 1 posted refresh */
 126 #define CONFIG_SYS_DDR_MODE             ((0x0406 << SDRAM_MODE_ESD_SHIFT) \
 127                                         | (0x0442 << SDRAM_MODE_SD_SHIFT))
 128                                         /* 0x04400442 */ /* DDR400 */
 129 #define CONFIG_SYS_DDR_MODE2            0x00000000
 130
 131 /*
 132  * Memory test
 133  */
 134 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
 135 #define CONFIG_SYS_MEMTEST_START        0x00040000 /* memtest region */
 136 #define CONFIG_SYS_MEMTEST_END          0x0ef70010
 137
 138 /*
 139  * The reserved memory
 140  */
 141 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 142
 143 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 144 #define CONFIG_SYS_RAMBOOT
 145 #else
 146 #undef  CONFIG_SYS_RAMBOOT
 147 #endif
 148
 149 #define CONFIG_SYS_MONITOR_LEN  (512 * 1024) /* Reserve 512 kB for Mon */
 150 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 151
 152 /*
 153  * Initial RAM Base Address Setup
 154  */
 155 #define CONFIG_SYS_INIT_RAM_LOCK        1
 156 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 157 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 158 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 159                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 160
 161 /*
 162  * FLASH on the Local Bus
 163  */
 164 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 165 #define CONFIG_SYS_FLASH_SIZE           8 /* max FLASH size is 32M */
 166
 167 #define CONFIG_SYS_FLASH_EMPTY_INFO             /* display empty sectors */
 168
 169
 170 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 171 #define CONFIG_SYS_MAX_FLASH_SECT       256 /* max sectors per device */
 172
 173 #undef  CONFIG_SYS_FLASH_CHECKSUM
 174 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 175 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 176
 177 /*
 178  * NAND Flash on the Local Bus
 179  */
 180 #define CONFIG_SYS_NAND_BASE    0xE0600000
 181
 182
 183 /* Vitesse 7385 */
 184
 185 #define CONFIG_SYS_VSC7385_BASE 0xF0000000
 186
 187 /*
 188  * Serial Port
 189  */
 190 #define CONFIG_SYS_NS16550_SERIAL
 191 #define CONFIG_SYS_NS16550_REG_SIZE     1
 192 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 193
 194 #define CONFIG_SYS_BAUDRATE_TABLE \
 195                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 196
 197 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 198 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 199
 200 /* SERDES */
 201 #define CONFIG_FSL_SERDES
 202 #define CONFIG_FSL_SERDES1      0xe3000
 203 #define CONFIG_FSL_SERDES2      0xe3100
 204
 205 /* I2C */
 206 #define CONFIG_SYS_I2C
 207 #define CONFIG_SYS_I2C_FSL
 208 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 209 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 210 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 211 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }
 212
 213 /*
 214  * Config on-board RTC
 215  */
 216 #define CONFIG_RTC_DS1374       /* use ds1374 rtc via i2c */
 217 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
 218
 219 /*
 220  * General PCI
 221  * Addresses are mapped 1-1.
 222  */
 223 #define CONFIG_SYS_PCI_MEM_BASE         0x80000000
 224 #define CONFIG_SYS_PCI_MEM_PHYS         CONFIG_SYS_PCI_MEM_BASE
 225 #define CONFIG_SYS_PCI_MEM_SIZE         0x10000000 /* 256M */
 226 #define CONFIG_SYS_PCI_MMIO_BASE        0x90000000
 227 #define CONFIG_SYS_PCI_MMIO_PHYS        CONFIG_SYS_PCI_MMIO_BASE
 228 #define CONFIG_SYS_PCI_MMIO_SIZE        0x10000000 /* 256M */
 229 #define CONFIG_SYS_PCI_IO_BASE          0x00000000
 230 #define CONFIG_SYS_PCI_IO_PHYS          0xE0300000
 231 #define CONFIG_SYS_PCI_IO_SIZE          0x100000 /* 1M */
 232
 233 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL    CONFIG_SYS_SDRAM_BASE
 234 #define CONFIG_SYS_PCI_SLV_MEM_BUS      0x00000000
 235 #define CONFIG_SYS_PCI_SLV_MEM_SIZE     0x80000000
 236
 237 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 238 #define CONFIG_SYS_PCIE1_CFG_BASE       0xA0000000
 239 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x08000000
 240 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA8000000
 241 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA8000000
 242 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 243 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 244 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB8000000
 245 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 246
 247 #define CONFIG_SYS_PCIE2_BASE           0xC0000000
 248 #define CONFIG_SYS_PCIE2_CFG_BASE       0xC0000000
 249 #define CONFIG_SYS_PCIE2_CFG_SIZE       0x08000000
 250 #define CONFIG_SYS_PCIE2_MEM_BASE       0xC8000000
 251 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xC8000000
 252 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000
 253 #define CONFIG_SYS_PCIE2_IO_BASE        0x00000000
 254 #define CONFIG_SYS_PCIE2_IO_PHYS        0xD8000000
 255 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000
 256
 257 #ifdef CONFIG_PCI
 258 #define CONFIG_PCI_INDIRECT_BRIDGE
 259
 260 #undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
 261 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 262 #endif  /* CONFIG_PCI */
 263
 264 /*
 265  * TSEC
 266  */
 267 #ifdef CONFIG_TSEC_ENET
 268
 269 #define CONFIG_GMII                     /* MII PHY management */
 270
 271 #define CONFIG_TSEC1
 272
 273 #ifdef CONFIG_TSEC1
 274 #define CONFIG_HAS_ETH0
 275 #define CONFIG_TSEC1_NAME               "TSEC0"
 276 #define CONFIG_SYS_TSEC1_OFFSET         0x24000
 277 #define TSEC1_PHY_ADDR                  2
 278 #define TSEC1_FLAGS                     (TSEC_GIGABIT | TSEC_REDUCED)
 279 #define TSEC1_PHYIDX                    0
 280 #endif
 281
 282 #ifdef CONFIG_TSEC2
 283 #define CONFIG_HAS_ETH1
 284 #define CONFIG_TSEC2_NAME               "TSEC1"
 285 #define CONFIG_SYS_TSEC2_OFFSET         0x25000
 286 #define TSEC2_PHY_ADDR                  0x1c
 287 #define TSEC2_FLAGS                     (TSEC_GIGABIT | TSEC_REDUCED)
 288 #define TSEC2_PHYIDX                    0
 289 #endif
 290
 291 /* Options are: TSEC[0-1] */
 292 #define CONFIG_ETHPRIME                 "TSEC0"
 293
 294 #endif
 295
 296 /*
 297  * SATA
 298  */
 299 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 300 #define CONFIG_SATA1
 301 #define CONFIG_SYS_SATA1_OFFSET 0x18000
 302 #define CONFIG_SYS_SATA1        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
 303 #define CONFIG_SYS_SATA1_FLAGS  FLAGS_DMA
 304 #define CONFIG_SATA2
 305 #define CONFIG_SYS_SATA2_OFFSET 0x19000
 306 #define CONFIG_SYS_SATA2        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
 307 #define CONFIG_SYS_SATA2_FLAGS  FLAGS_DMA
 308
 309 #ifdef CONFIG_FSL_SATA
 310 #define CONFIG_LBA48
 311 #endif
 312
 313 /*
 314  * Environment
 315  */
 316
 317 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 318 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 319
 320 /*
 321  * BOOTP options
 322  */
 323 #define CONFIG_BOOTP_BOOTFILESIZE
 324
 325 /*
 326  * Command line configuration.
 327  */
 328
 329 #undef CONFIG_WATCHDOG          /* watchdog disabled */
 330
 331 #ifdef CONFIG_MMC
 332 #define CONFIG_FSL_ESDHC_PIN_MUX
 333 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
 334 #endif
 335
 336 /*
 337  * Miscellaneous configurable options
 338  */
 339 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 340
 341 /*
 342  * For booting Linux, the board info and command line data
 343  * have to be in the first 256 MB of memory, since this is
 344  * the maximum mapped by the Linux kernel during initialization.
 345  */
 346 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 347 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 348
 349 #if defined(CONFIG_CMD_KGDB)
 350 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 351 #endif
 352
 353 /*
 354  * Environment Configuration
 355  */
 356 #define CONFIG_ENV_OVERWRITE
 357
 358 #define CONFIG_HAS_FSL_DR_USB
 359 #define CONFIG_USB_EHCI_FSL
 360 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 361
 362 #define CONFIG_NETDEV           "eth1"
 363
 364 #define CONFIG_HOSTNAME         "mpc837x_rdb"
 365 #define CONFIG_ROOTPATH         "/nfsroot"
 366 #define CONFIG_RAMDISKFILE      "rootfs.ext2.gz.uboot"
 367 #define CONFIG_BOOTFILE         "uImage"
 368                                 /* U-Boot image on TFTP server */
 369 #define CONFIG_UBOOTPATH        "u-boot.bin"
 370 #define CONFIG_FDTFILE          "mpc8379_rdb.dtb"
 371
 372                                 /* default location for tftp and bootm */
 373 #define CONFIG_LOADADDR         800000
 374
 375 #define CONFIG_EXTRA_ENV_SETTINGS \
 376         "netdev=" CONFIG_NETDEV "\0"                            \
 377         "uboot=" CONFIG_UBOOTPATH "\0"                                  \
 378         "tftpflash=tftp $loadaddr $uboot;"                              \
 379                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 380                         " +$filesize; " \
 381                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 382                         " +$filesize; " \
 383                 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
 384                         " $filesize; "  \
 385                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 386                         " +$filesize; " \
 387                 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
 388                         " $filesize\0"  \
 389         "fdtaddr=780000\0"                                              \
 390         "fdtfile=" CONFIG_FDTFILE "\0"                                  \
 391         "ramdiskaddr=1000000\0"                                         \
 392         "ramdiskfile=" CONFIG_RAMDISKFILE "\0"                          \
 393         "console=ttyS0\0"                                               \
 394         "setbootargs=setenv bootargs "                                  \
 395                 "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
 396         "setipargs=setenv bootargs nfsroot=$serverip:$rootpath "        \
 397                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 398                                                         "$netdev:off "  \
 399                 "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
 400
 401 #define CONFIG_NFSBOOTCOMMAND                                           \
 402         "setenv rootdev /dev/nfs;"                                      \
 403         "run setbootargs;"                                              \
 404         "run setipargs;"                                                \
 405         "tftp $loadaddr $bootfile;"                                     \
 406         "tftp $fdtaddr $fdtfile;"                                       \
 407         "bootm $loadaddr - $fdtaddr"
 408
 409 #define CONFIG_RAMBOOTCOMMAND                                           \
 410         "setenv rootdev /dev/ram;"                                      \
 411         "run setbootargs;"                                              \
 412         "tftp $ramdiskaddr $ramdiskfile;"                               \
 413         "tftp $loadaddr $bootfile;"                                     \
 414         "tftp $fdtaddr $fdtfile;"                                       \
 415         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 416
 417 #endif  /* __CONFIG_H */