include/configs/MPC837XEMDS.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2007 Freescale Semiconductor, Inc.
   4  * Dave Liu <daveliu@freescale.com>
   5  */
   6
   7 #ifndef __CONFIG_H
   8 #define __CONFIG_H
   9
  10 /*
  11  * High Level Configuration Options
  12  */
  13 #define CONFIG_E300             1 /* E300 family */
  14
  15 /*
  16  * IP blocks clock configuration
  17  */
  18 #define CONFIG_SYS_SCCR_TSEC1CM 1       /* CSB:eTSEC1 = 1:1 */
  19 #define CONFIG_SYS_SCCR_TSEC2CM 1       /* CSB:eTSEC2 = 1:1 */
  20 #define CONFIG_SYS_SCCR_SATACM  SCCR_SATACM_2   /* CSB:SATA[0:3] = 2:1 */
  21
  22 /*
  23  * System IO Config
  24  */
  25 #define CONFIG_SYS_SICRH                0x00000000
  26 #define CONFIG_SYS_SICRL                0x00000000
  27
  28 /*
  29  * Output Buffer Impedance
  30  */
  31 #define CONFIG_SYS_OBIR         0x31100000
  32
  33 #define CONFIG_HWCONFIG
  34
  35 /*
  36  * DDR Setup
  37  */
  38 #define CONFIG_SYS_SDRAM_BASE           0x00000000 /* DDR is system memory */
  39 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
  40 #define CONFIG_SYS_83XX_DDR_USES_CS0
  41 #define CONFIG_SYS_DDRCDR_VALUE         (DDRCDR_DHC_EN \
  42                                         | DDRCDR_ODT \
  43                                         | DDRCDR_Q_DRN)
  44                                         /* 0x80080001 */ /* ODT 150ohm on SoC */
  45
  46 #undef CONFIG_DDR_ECC           /* support DDR ECC function */
  47 #undef CONFIG_DDR_ECC_CMD       /* Use DDR ECC user commands */
  48
  49 #define CONFIG_SPD_EEPROM       /* Use SPD EEPROM for DDR setup */
  50 #define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */
  51
  52 #if defined(CONFIG_SPD_EEPROM)
  53 #define SPD_EEPROM_ADDRESS      0x51 /* I2C address of DDR SODIMM SPD */
  54 #else
  55 /*
  56  * Manually set up DDR parameters
  57  * WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM
  58  * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5
  59  */
  60 #define CONFIG_SYS_DDR_SIZE             512 /* MB */
  61 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f
  62 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
  63                         | CSCONFIG_ODT_RD_NEVER  /* ODT_RD to none */ \
  64                         | CSCONFIG_ODT_WR_ONLY_CURRENT  /* ODT_WR to CSn */ \
  65                         | CSCONFIG_ROW_BIT_14 \
  66                         | CSCONFIG_COL_BIT_10)
  67                         /* 0x80010202 */
  68 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
  69 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
  70                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
  71                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
  72                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
  73                                 | (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
  74                                 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
  75                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
  76                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
  77                                 /* 0x00620802 */
  78 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
  79                                 | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
  80                                 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
  81                                 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
  82                                 | (13 << TIMING_CFG1_REFREC_SHIFT) \
  83                                 | (3 << TIMING_CFG1_WRREC_SHIFT) \
  84                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
  85                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
  86                                 /* 0x3935d322 */
  87 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
  88                                 | (6 << TIMING_CFG2_CPO_SHIFT) \
  89                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
  90                                 | (4 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
  91                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
  92                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
  93                                 | (8 << TIMING_CFG2_FOUR_ACT_SHIFT))
  94                                 /* 0x131088c8 */
  95 #define CONFIG_SYS_DDR_INTERVAL ((0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT) \
  96                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
  97                                 /* 0x03E00100 */
  98 #define CONFIG_SYS_DDR_SDRAM_CFG        0x43000000
  99 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00001000 /* 1 posted refresh */
 100 #define CONFIG_SYS_DDR_MODE     ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
 101                                 | (0x1432 << SDRAM_MODE_SD_SHIFT))
 102                                 /* ODT 150ohm CL=3, AL=1 on SDRAM */
 103 #define CONFIG_SYS_DDR_MODE2    0x00000000
 104 #endif
 105
 106 /*
 107  * Memory test
 108  */
 109 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
 110 #define CONFIG_SYS_MEMTEST_START        0x00040000 /* memtest region */
 111 #define CONFIG_SYS_MEMTEST_END          0x00140000
 112
 113 /*
 114  * The reserved memory
 115  */
 116 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 117
 118 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 119 #define CONFIG_SYS_RAMBOOT
 120 #else
 121 #undef CONFIG_SYS_RAMBOOT
 122 #endif
 123
 124 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
 125 #define CONFIG_SYS_MONITOR_LEN  (512 * 1024) /* Reserve 512 kB for Mon */
 126 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 127
 128 /*
 129  * Initial RAM Base Address Setup
 130  */
 131 #define CONFIG_SYS_INIT_RAM_LOCK        1
 132 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 133 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 134 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 135                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 136
 137 #define CONFIG_FSL_ELBC         1
 138
 139 /*
 140  * FLASH on the Local Bus
 141  */
 142 #define CONFIG_SYS_FLASH_BASE   0xFE000000 /* FLASH base address */
 143 #define CONFIG_SYS_FLASH_SIZE   32 /* max FLASH size is 32M */
 144
 145
 146 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 147 #define CONFIG_SYS_MAX_FLASH_SECT       256 /* max sectors per device */
 148
 149 #undef CONFIG_SYS_FLASH_CHECKSUM
 150 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 151 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 152
 153 /*
 154  * BCSR on the Local Bus
 155  */
 156 #define CONFIG_SYS_BCSR         0xF8000000
 157                                         /* Access window base at BCSR base */
 158
 159 /*
 160  * NAND Flash on the Local Bus
 161  */
 162 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 163 #define CONFIG_NAND_FSL_ELBC    1
 164
 165 #define CONFIG_SYS_NAND_BASE    0xE0600000
 166
 167
 168 /*
 169  * Serial Port
 170  */
 171 #define CONFIG_SYS_NS16550_SERIAL
 172 #define CONFIG_SYS_NS16550_REG_SIZE     1
 173 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 174
 175 #define CONFIG_SYS_BAUDRATE_TABLE  \
 176                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 177
 178 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 179 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 180
 181 /* I2C */
 182 #define CONFIG_SYS_I2C
 183 #define CONFIG_SYS_I2C_FSL
 184 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 185 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 186 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 187 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }
 188
 189 /*
 190  * Config on-board RTC
 191  */
 192 #define CONFIG_RTC_DS1374       /* use ds1374 rtc via i2c */
 193 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
 194
 195 /*
 196  * General PCI
 197  * Addresses are mapped 1-1.
 198  */
 199 #define CONFIG_SYS_PCI_MEM_BASE         0x80000000
 200 #define CONFIG_SYS_PCI_MEM_PHYS         CONFIG_SYS_PCI_MEM_BASE
 201 #define CONFIG_SYS_PCI_MEM_SIZE         0x10000000 /* 256M */
 202 #define CONFIG_SYS_PCI_MMIO_BASE        0x90000000
 203 #define CONFIG_SYS_PCI_MMIO_PHYS        CONFIG_SYS_PCI_MMIO_BASE
 204 #define CONFIG_SYS_PCI_MMIO_SIZE        0x10000000 /* 256M */
 205 #define CONFIG_SYS_PCI_IO_BASE          0x00000000
 206 #define CONFIG_SYS_PCI_IO_PHYS          0xE0300000
 207 #define CONFIG_SYS_PCI_IO_SIZE          0x100000 /* 1M */
 208
 209 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL    CONFIG_SYS_SDRAM_BASE
 210 #define CONFIG_SYS_PCI_SLV_MEM_BUS      0x00000000
 211 #define CONFIG_SYS_PCI_SLV_MEM_SIZE     0x80000000
 212
 213 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 214 #define CONFIG_SYS_PCIE1_CFG_BASE       0xA0000000
 215 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x08000000
 216 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA8000000
 217 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA8000000
 218 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 219 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 220 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB8000000
 221 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 222
 223 #define CONFIG_SYS_PCIE2_BASE           0xC0000000
 224 #define CONFIG_SYS_PCIE2_CFG_BASE       0xC0000000
 225 #define CONFIG_SYS_PCIE2_CFG_SIZE       0x08000000
 226 #define CONFIG_SYS_PCIE2_MEM_BASE       0xC8000000
 227 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xC8000000
 228 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000
 229 #define CONFIG_SYS_PCIE2_IO_BASE        0x00000000
 230 #define CONFIG_SYS_PCIE2_IO_PHYS        0xD8000000
 231 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000
 232
 233 #ifdef CONFIG_PCI
 234 #define CONFIG_PCI_INDIRECT_BRIDGE
 235 #ifndef __ASSEMBLY__
 236 extern int board_pci_host_broken(void);
 237 #endif
 238 #define CONFIG_PCIE
 239 #define CONFIG_PQ_MDS_PIB       1 /* PQ MDS Platform IO Board */
 240
 241 #define CONFIG_HAS_FSL_DR_USB   1 /* fixup device tree for the DR USB */
 242 #define CONFIG_USB_EHCI_FSL
 243 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 244
 245 #undef CONFIG_EEPRO100
 246 #undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
 247 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 248 #endif /* CONFIG_PCI */
 249
 250 /*
 251  * TSEC
 252  */
 253 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 254 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 255 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 256 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 257
 258 /*
 259  * TSEC ethernet configuration
 260  */
 261 #define CONFIG_TSEC1            1
 262 #define CONFIG_TSEC1_NAME       "eTSEC0"
 263 #define CONFIG_TSEC2            1
 264 #define CONFIG_TSEC2_NAME       "eTSEC1"
 265 #define TSEC1_PHY_ADDR          2
 266 #define TSEC2_PHY_ADDR          3
 267 #define TSEC1_PHY_ADDR_SGMII    8
 268 #define TSEC2_PHY_ADDR_SGMII    4
 269 #define TSEC1_PHYIDX            0
 270 #define TSEC2_PHYIDX            0
 271 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 272 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 273
 274 /* Options are: TSEC[0-1] */
 275 #define CONFIG_ETHPRIME         "eTSEC1"
 276
 277 /* SERDES */
 278 #define CONFIG_FSL_SERDES
 279 #define CONFIG_FSL_SERDES1      0xe3000
 280 #define CONFIG_FSL_SERDES2      0xe3100
 281
 282 /*
 283  * SATA
 284  */
 285 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 286 #define CONFIG_SATA1
 287 #define CONFIG_SYS_SATA1_OFFSET 0x18000
 288 #define CONFIG_SYS_SATA1        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
 289 #define CONFIG_SYS_SATA1_FLAGS  FLAGS_DMA
 290 #define CONFIG_SATA2
 291 #define CONFIG_SYS_SATA2_OFFSET 0x19000
 292 #define CONFIG_SYS_SATA2        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
 293 #define CONFIG_SYS_SATA2_FLAGS  FLAGS_DMA
 294
 295 #ifdef CONFIG_FSL_SATA
 296 #define CONFIG_LBA48
 297 #endif
 298
 299 /*
 300  * Environment
 301  */
 302 #ifndef CONFIG_SYS_RAMBOOT
 303         #define CONFIG_ENV_ADDR         \
 304                         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 305         #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 306         #define CONFIG_ENV_SIZE         0x2000
 307 #else
 308         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 309         #define CONFIG_ENV_SIZE         0x2000
 310 #endif
 311
 312 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 313 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 314
 315 /*
 316  * BOOTP options
 317  */
 318 #define CONFIG_BOOTP_BOOTFILESIZE
 319
 320 /*
 321  * Command line configuration.
 322  */
 323
 324 #undef CONFIG_WATCHDOG          /* watchdog disabled */
 325
 326 #ifdef CONFIG_MMC
 327 #define CONFIG_FSL_ESDHC_PIN_MUX
 328 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
 329 #endif
 330
 331 /*
 332  * Miscellaneous configurable options
 333  */
 334 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 335
 336 /*
 337  * For booting Linux, the board info and command line data
 338  * have to be in the first 256 MB of memory, since this is
 339  * the maximum mapped by the Linux kernel during initialization.
 340  */
 341 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 342 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 343
 344 #if defined(CONFIG_CMD_KGDB)
 345 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 346 #endif
 347
 348 /*
 349  * Environment Configuration
 350  */
 351
 352 #define CONFIG_ENV_OVERWRITE
 353
 354 #if defined(CONFIG_TSEC_ENET)
 355 #define CONFIG_HAS_ETH0
 356 #define CONFIG_HAS_ETH1
 357 #endif
 358
 359 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 360
 361 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 362         "netdev=eth0\0"                                                 \
 363         "consoledev=ttyS0\0"                                            \
 364         "ramdiskaddr=1000000\0"                                         \
 365         "ramdiskfile=ramfs.83xx\0"                                      \
 366         "fdtaddr=780000\0"                                              \
 367         "fdtfile=mpc8379_mds.dtb\0"                                     \
 368         ""
 369
 370 #define CONFIG_NFSBOOTCOMMAND                                           \
 371         "setenv bootargs root=/dev/nfs rw "                             \
 372                 "nfsroot=$serverip:$rootpath "                          \
 373                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 374                                                         "$netdev:off "  \
 375                 "console=$consoledev,$baudrate $othbootargs;"           \
 376         "tftp $loadaddr $bootfile;"                                     \
 377         "tftp $fdtaddr $fdtfile;"                                       \
 378         "bootm $loadaddr - $fdtaddr"
 379
 380 #define CONFIG_RAMBOOTCOMMAND                                           \
 381         "setenv bootargs root=/dev/ram rw "                             \
 382                 "console=$consoledev,$baudrate $othbootargs;"           \
 383         "tftp $ramdiskaddr $ramdiskfile;"                               \
 384         "tftp $loadaddr $bootfile;"                                     \
 385         "tftp $fdtaddr $fdtfile;"                                       \
 386         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 387
 388 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
 389
 390 #endif  /* __CONFIG_H */