include/configs/MPC8360ERDK.h

   1 /*
   2  * Copyright (C) 2006 Freescale Semiconductor, Inc.
   3  *                    Dave Liu <daveliu@freescale.com>
   4  *
   5  * Copyright (C) 2007 Logic Product Development, Inc.
   6  *                    Peter Barada <peterb@logicpd.com>
   7  *
   8  * Copyright (C) 2007 MontaVista Software, Inc.
   9  *                    Anton Vorontsov <avorontsov@ru.mvista.com>
  10  *
  11  * SPDX-License-Identifier:     GPL-2.0+
  12  */
  13
  14 #ifndef __CONFIG_H
  15 #define __CONFIG_H
  16
  17 /*
  18  * High Level Configuration Options
  19  */
  20 #define CONFIG_E300             1 /* E300 family */
  21 #define CONFIG_QE               1 /* Has QE */
  22 #define CONFIG_MPC83xx          1 /* MPC83xx family */
  23 #define CONFIG_MPC8360          1 /* MPC8360 CPU specific */
  24 #define CONFIG_MPC8360ERDK      1 /* MPC8360ERDK board specific */
  25
  26 #define CONFIG_SYS_TEXT_BASE    0xFF800000
  27
  28 /*
  29  * System Clock Setup
  30  */
  31 #ifdef CONFIG_CLKIN_33MHZ
  32 #define CONFIG_83XX_CLKIN               33333333
  33 #define CONFIG_SYS_CLK_FREQ             33333333
  34 #define CONFIG_PCI_33M                          1
  35 #define HRCWL_CSB_TO_CLKIN_MPC8360ERDK  HRCWL_CSB_TO_CLKIN_10X1
  36 #else
  37 #define CONFIG_83XX_CLKIN               66000000
  38 #define CONFIG_SYS_CLK_FREQ             66000000
  39 #define CONFIG_PCI_66M                          1
  40 #define HRCWL_CSB_TO_CLKIN_MPC8360ERDK  HRCWL_CSB_TO_CLKIN_5X1
  41 #endif /* CONFIG_CLKIN_33MHZ */
  42
  43 /*
  44  * Hardware Reset Configuration Word
  45  */
  46 #define CONFIG_SYS_HRCW_LOW (\
  47         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  48         HRCWL_DDR_TO_SCB_CLK_1X1 |\
  49         HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\
  50         HRCWL_CORE_TO_CSB_2X1 |\
  51         HRCWL_CE_TO_PLL_1X15)
  52
  53 #define CONFIG_SYS_HRCW_HIGH (\
  54         HRCWH_PCI_HOST |\
  55         HRCWH_PCI1_ARBITER_ENABLE |\
  56         HRCWH_PCICKDRV_ENABLE |\
  57         HRCWH_CORE_ENABLE |\
  58         HRCWH_FROM_0X00000100 |\
  59         HRCWH_BOOTSEQ_DISABLE |\
  60         HRCWH_SW_WATCHDOG_DISABLE |\
  61         HRCWH_ROM_LOC_LOCAL_16BIT |\
  62         HRCWH_SECONDARY_DDR_DISABLE |\
  63         HRCWH_BIG_ENDIAN |\
  64         HRCWH_LALE_EARLY)
  65
  66 /*
  67  * System IO Config
  68  */
  69 #define CONFIG_SYS_SICRH                0x00000000
  70 #define CONFIG_SYS_SICRL                0x40000000
  71
  72 #define CONFIG_BOARD_EARLY_INIT_R
  73
  74 /*
  75  * IMMR new address
  76  */
  77 #define CONFIG_SYS_IMMR         0xE0000000
  78
  79 /*
  80  * DDR Setup
  81  */
  82 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
  83 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  84 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
  85 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   (DDR_SDRAM_CLK_CNTL_SS_EN \
  86                                         | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
  87
  88 #define CONFIG_SYS_83XX_DDR_USES_CS0
  89
  90 #define CONFIG_DDR_ECC          /* support DDR ECC function */
  91 #define CONFIG_DDR_ECC_CMD      /* Use DDR ECC user commands */
  92
  93 /*
  94  * DDRCDR - DDR Control Driver Register
  95  */
  96 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \
  97                                 | DDRCDR_ODT \
  98                                 | DDRCDR_Q_DRN)
  99                                 /* 0x80080001 */
 100
 101 #undef CONFIG_SPD_EEPROM        /* Do not use SPD EEPROM for DDR setup */
 102
 103 /*
 104  * Manually set up DDR parameters
 105  */
 106 #define CONFIG_DDR_II
 107 #define CONFIG_SYS_DDR_SIZE             256 /* MB */
 108 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000000f
 109 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
 110                                         | CSCONFIG_ROW_BIT_13 \
 111                                         | CSCONFIG_COL_BIT_10 \
 112                                         | CSCONFIG_ODT_WR_ONLY_CURRENT)
 113 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SDRAM_TYPE_DDR2 \
 114                                         | SDRAM_CFG_ECC_EN)
 115 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00001000
 116 #define CONFIG_SYS_DDR_CLK_CNTL         (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
 117 #define CONFIG_SYS_DDR_INTERVAL         ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) \
 118                                         | (1115 << SDRAM_INTERVAL_REFINT_SHIFT))
 119 #define CONFIG_SYS_DDR_MODE             0x47800432
 120 #define CONFIG_SYS_DDR_MODE2            0x8000c000
 121
 122 #define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
 123                                  (9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
 124                                  (3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
 125                                  (3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
 126                                  (0 << TIMING_CFG0_WWT_SHIFT) | \
 127                                  (0 << TIMING_CFG0_RRT_SHIFT) | \
 128                                  (0 << TIMING_CFG0_WRT_SHIFT) | \
 129                                  (0 << TIMING_CFG0_RWT_SHIFT))
 130
 131 #define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_30) | \
 132                                  (2 << TIMING_CFG1_WRTORD_SHIFT) | \
 133                                  (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
 134                                  (3 << TIMING_CFG1_WRREC_SHIFT) | \
 135                                  (10 << TIMING_CFG1_REFREC_SHIFT) | \
 136                                  (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
 137                                  (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
 138                                  (3 << TIMING_CFG1_PRETOACT_SHIFT))
 139
 140 #define CONFIG_SYS_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
 141                                  (4 << TIMING_CFG2_CKE_PLS_SHIFT) | \
 142                                  (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
 143                                  (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
 144                                  (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
 145                                  (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
 146                                  (0 << TIMING_CFG2_CPO_SHIFT))
 147
 148 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 149
 150 /*
 151  * Memory test
 152  */
 153 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
 154 #define CONFIG_SYS_MEMTEST_START        0x00000000 /* memtest region */
 155 #define CONFIG_SYS_MEMTEST_END          0x00100000
 156
 157 /*
 158  * The reserved memory
 159  */
 160 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 161 #define CONFIG_SYS_FLASH_BASE           0xFF800000 /* FLASH base address */
 162
 163 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 164 #define CONFIG_SYS_RAMBOOT
 165 #else
 166 #undef  CONFIG_SYS_RAMBOOT
 167 #endif
 168
 169 #define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
 170 #define CONFIG_SYS_MALLOC_LEN   (256 * 1024) /* Reserved for malloc */
 171
 172 /*
 173  * Initial RAM Base Address Setup
 174  */
 175 #define CONFIG_SYS_INIT_RAM_LOCK        1
 176 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 177 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 178 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 179                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 180
 181 /*
 182  * Local Bus Configuration & Clock Setup
 183  */
 184 #define CONFIG_SYS_LCRR_DBYP    LCRR_DBYP
 185 #define CONFIG_SYS_LCRR_CLKDIV  LCRR_CLKDIV_4
 186 #define CONFIG_SYS_LBC_LBCR     0x00000000
 187
 188 /*
 189  * FLASH on the Local Bus
 190  */
 191 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 192 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 193 #define CONFIG_SYS_FLASH_SIZE           8 /* max FLASH size is 32M */
 194 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use intel Flash protection. */
 195
 196                                         /* Window base at flash base */
 197 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 198 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_32MB)
 199
 200 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 201                                 | BR_PS_16      /* 16 bit port */ \
 202                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 203                                 | BR_V)         /* valid */
 204 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 205                                 | OR_UPM_XAM \
 206                                 | OR_GPCM_CSNT \
 207                                 | OR_GPCM_ACS_DIV2 \
 208                                 | OR_GPCM_XACS \
 209                                 | OR_GPCM_SCY_15 \
 210                                 | OR_GPCM_TRLX_SET \
 211                                 | OR_GPCM_EHTR_SET \
 212                                 | OR_GPCM_EAD)
 213
 214 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 215 #define CONFIG_SYS_MAX_FLASH_SECT       256 /* max sectors per device */
 216
 217 #undef  CONFIG_SYS_FLASH_CHECKSUM
 218
 219 /*
 220  * NAND flash on the local bus
 221  */
 222 #define CONFIG_SYS_NAND_BASE            0x60000000
 223 #define CONFIG_CMD_NAND         1
 224 #define CONFIG_NAND_FSL_UPM     1
 225 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 226 #define CONFIG_MTD_NAND_VERIFY_WRITE
 227
 228 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_NAND_BASE
 229 /*
 230  * [RFC] Comment said 4KB window; code said 256MB window; OR1 says 64MB
 231  * ... What's correct?
 232  */
 233 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_256MB)
 234
 235 /* Port size 8 bit, UPMA */
 236 #define CONFIG_SYS_BR1_PRELIM           (CONFIG_SYS_NAND_BASE \
 237                                         | BR_PS_8 \
 238                                         | BR_MS_UPMA \
 239                                         | BR_V)
 240                                         /* 0x60000881 */
 241 #define CONFIG_SYS_OR1_PRELIM           (OR_AM_64MB | OR_UPM_EAD)
 242                                         /* 0xFC000001 */
 243
 244 /*
 245  * Fujitsu MB86277 (MINT) graphics controller
 246  */
 247 #define CONFIG_SYS_VIDEO_BASE           0x70000000
 248
 249 #define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_VIDEO_BASE
 250 #define CONFIG_SYS_LBLAWAR2_PRELIM      (LBLAWAR_EN | LBLAWAR_64MB)
 251
 252 /* Port size 32 bit, UPMB */
 253 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_VIDEO_BASE \
 254                                 | BR_PS_32 \
 255                                 | BR_MS_UPMB \
 256                                 | BR_V)
 257                                 /* 0x000018a1 */
 258 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_64MB | OR_UPM_EAD)
 259                                 /* 0xFC000001 */
 260
 261 /*
 262  * Serial Port
 263  */
 264 #define CONFIG_CONS_INDEX       1
 265 #define CONFIG_SYS_NS16550
 266 #define CONFIG_SYS_NS16550_SERIAL
 267 #define CONFIG_SYS_NS16550_REG_SIZE     1
 268 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 269
 270 #define CONFIG_SYS_BAUDRATE_TABLE  \
 271                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 272
 273 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 274 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 275
 276 #define CONFIG_CMDLINE_EDITING  1       /* add command line history */
 277 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support */
 278 /* Use the HUSH parser */
 279 #define CONFIG_SYS_HUSH_PARSER
 280
 281 /* Pass open firmware flat tree */
 282 #define CONFIG_OF_LIBFDT        1
 283 #define CONFIG_OF_BOARD_SETUP   1
 284 #define CONFIG_OF_STDOUT_VIA_ALIAS
 285
 286 /* I2C */
 287 #define CONFIG_SYS_I2C
 288 #define CONFIG_SYS_I2C_FSL
 289 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 290 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 291 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 292 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 293 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 294 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 295 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x52} }
 296
 297 /*
 298  * General PCI
 299  * Addresses are mapped 1-1.
 300  */
 301 #define CONFIG_PCI
 302
 303 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 304 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 305 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000 /* 256M */
 306 #define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 307 #define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 308 #define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000 /* 256M */
 309 #define CONFIG_SYS_PCI1_IO_BASE         0xE0300000
 310 #define CONFIG_SYS_PCI1_IO_PHYS         0xE0300000
 311 #define CONFIG_SYS_PCI1_IO_SIZE         0x100000 /* 1M */
 312
 313 #ifdef CONFIG_PCI
 314 #define CONFIG_PCI_INDIRECT_BRIDGE
 315
 316 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 317
 318 #undef CONFIG_EEPRO100
 319 #undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
 320 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 321
 322 #endif  /* CONFIG_PCI */
 323
 324 /*
 325  * QE UEC ethernet configuration
 326  */
 327 #define CONFIG_UEC_ETH
 328 #define CONFIG_ETHPRIME         "UEC0"
 329
 330 #define CONFIG_UEC_ETH1         /* GETH1 */
 331
 332 #ifdef CONFIG_UEC_ETH1
 333 #define CONFIG_SYS_UEC1_UCC_NUM 0       /* UCC1 */
 334 #define CONFIG_SYS_UEC1_RX_CLK          QE_CLK_NONE
 335 #define CONFIG_SYS_UEC1_TX_CLK          QE_CLK9
 336 #define CONFIG_SYS_UEC1_ETH_TYPE        GIGA_ETH
 337 #define CONFIG_SYS_UEC1_PHY_ADDR        2
 338 #define CONFIG_SYS_UEC1_INTERFACE_TYPE  PHY_INTERFACE_MODE_RGMII_RXID
 339 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 340 #endif
 341
 342 #define CONFIG_UEC_ETH2         /* GETH2 */
 343
 344 #ifdef CONFIG_UEC_ETH2
 345 #define CONFIG_SYS_UEC2_UCC_NUM 1       /* UCC2 */
 346 #define CONFIG_SYS_UEC2_RX_CLK          QE_CLK_NONE
 347 #define CONFIG_SYS_UEC2_TX_CLK          QE_CLK4
 348 #define CONFIG_SYS_UEC2_ETH_TYPE        GIGA_ETH
 349 #define CONFIG_SYS_UEC2_PHY_ADDR        4
 350 #define CONFIG_SYS_UEC2_INTERFACE_TYPE  PHY_INTERFACE_MODE_RGMII_RXID
 351 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 352 #endif
 353
 354 /*
 355  * Environment
 356  */
 357
 358 #ifndef CONFIG_SYS_RAMBOOT
 359 #define CONFIG_ENV_IS_IN_FLASH  1
 360 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 361 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 362 #define CONFIG_ENV_SIZE         0x20000
 363 #else /* CONFIG_SYS_RAMBOOT */
 364 #define CONFIG_SYS_NO_FLASH     1       /* Flash is not usable now */
 365 #define CONFIG_ENV_IS_NOWHERE   1       /* Store ENV in memory only */
 366 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 367 #define CONFIG_ENV_SIZE         0x2000
 368 #endif /* CONFIG_SYS_RAMBOOT */
 369
 370 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 371 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 372
 373 /*
 374  * BOOTP options
 375  */
 376 #define CONFIG_BOOTP_BOOTFILESIZE
 377 #define CONFIG_BOOTP_BOOTPATH
 378 #define CONFIG_BOOTP_GATEWAY
 379 #define CONFIG_BOOTP_HOSTNAME
 380
 381
 382 /*
 383  * Command line configuration.
 384  */
 385 #include <config_cmd_default.h>
 386
 387 #define CONFIG_CMD_PING
 388 #define CONFIG_CMD_I2C
 389 #define CONFIG_CMD_ASKENV
 390 #define CONFIG_CMD_DHCP
 391
 392 #if defined(CONFIG_PCI)
 393 #define CONFIG_CMD_PCI
 394 #endif
 395
 396 #if defined(CONFIG_SYS_RAMBOOT)
 397 #undef CONFIG_CMD_SAVEENV
 398 #undef CONFIG_CMD_LOADS
 399 #endif
 400
 401 #undef CONFIG_WATCHDOG          /* watchdog disabled */
 402
 403 /*
 404  * Miscellaneous configurable options
 405  */
 406 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 407 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 408
 409 #if defined(CONFIG_CMD_KGDB)
 410         #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 411 #else
 412         #define CONFIG_SYS_CBSIZE       256 /* Console I/O Buffer Size */
 413 #endif
 414
 415                                 /* Print Buffer Size */
 416 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 417 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 418                                 /* Boot Argument Buffer Size */
 419 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 420
 421 /*
 422  * For booting Linux, the board info and command line data
 423  * have to be in the first 256 MB of memory, since this is
 424  * the maximum mapped by the Linux kernel during initialization.
 425  */
 426 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 427
 428 /*
 429  * Core HID Setup
 430  */
 431 #define CONFIG_SYS_HID0_INIT    0x000000000
 432 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 433                                  HID0_ENABLE_INSTRUCTION_CACHE)
 434 #define CONFIG_SYS_HID2         HID2_HBE
 435
 436 /*
 437  * MMU Setup
 438  */
 439
 440 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
 441
 442 /* DDR: cache cacheable */
 443 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE \
 444                                 | BATL_PP_RW \
 445                                 | BATL_MEMCOHERENCE)
 446 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE \
 447                                 | BATU_BL_256M \
 448                                 | BATU_VS \
 449                                 | BATU_VP)
 450 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 451 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 452
 453 /* IMMRBAR & PCI IO: cache-inhibit and guarded */
 454 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR \
 455                                 | BATL_PP_RW \
 456                                 | BATL_CACHEINHIBIT \
 457                                 | BATL_GUARDEDSTORAGE)
 458 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR \
 459                                 | BATU_BL_4M \
 460                                 | BATU_VS \
 461                                 | BATU_VP)
 462 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 463 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 464
 465 /* NAND: cache-inhibit and guarded */
 466 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_NAND_BASE \
 467                                 | BATL_PP_RW \
 468                                 | BATL_CACHEINHIBIT \
 469                                 | BATL_GUARDEDSTORAGE)
 470 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_NAND_BASE \
 471                                 | BATU_BL_64M \
 472                                 | BATU_VS \
 473                                 | BATU_VP)
 474 #define CONFIG_SYS_DBAT2L       CONFIG_SYS_IBAT2L
 475 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 476
 477 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 478 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_FLASH_BASE \
 479                                 | BATL_PP_RW \
 480                                 | BATL_MEMCOHERENCE)
 481 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_FLASH_BASE \
 482                                 | BATU_BL_32M \
 483                                 | BATU_VS \
 484                                 | BATU_VP)
 485 #define CONFIG_SYS_DBAT3L       (CONFIG_SYS_FLASH_BASE \
 486                                 | BATL_PP_RW \
 487                                 | BATL_CACHEINHIBIT \
 488                                 | BATL_GUARDEDSTORAGE)
 489 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 490
 491 /* Stack in dcache: cacheable, no memory coherence */
 492 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_INIT_RAM_ADDR \
 493                                 | BATL_PP_RW)
 494 #define CONFIG_SYS_IBAT4U       (CONFIG_SYS_INIT_RAM_ADDR \
 495                                 | BATU_BL_128K \
 496                                 | BATU_VS \
 497                                 | BATU_VP)
 498 #define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
 499 #define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U
 500
 501 #define CONFIG_SYS_IBAT5L       (CONFIG_SYS_VIDEO_BASE \
 502                                 | BATL_PP_RW \
 503                                 | BATL_CACHEINHIBIT \
 504                                 | BATL_GUARDEDSTORAGE)
 505 #define CONFIG_SYS_IBAT5U       (CONFIG_SYS_VIDEO_BASE \
 506                                 | BATU_BL_64M \
 507                                 | BATU_VS \
 508                                 | BATU_VP)
 509 #define CONFIG_SYS_DBAT5L       CONFIG_SYS_IBAT5L
 510 #define CONFIG_SYS_DBAT5U       CONFIG_SYS_IBAT5U
 511
 512 #ifdef CONFIG_PCI
 513 /* PCI MEM space: cacheable */
 514 #define CONFIG_SYS_IBAT6L       (CONFIG_SYS_PCI1_MEM_PHYS \
 515                                 | BATL_PP_RW \
 516                                 | BATL_MEMCOHERENCE)
 517 #define CONFIG_SYS_IBAT6U       (CONFIG_SYS_PCI1_MEM_PHYS \
 518                                 | BATU_BL_256M \
 519                                 | BATU_VS \
 520                                 | BATU_VP)
 521 #define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
 522 #define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
 523 /* PCI MMIO space: cache-inhibit and guarded */
 524 #define CONFIG_SYS_IBAT7L       (CONFIG_SYS_PCI1_MMIO_PHYS \
 525                                 | BATL_PP_RW \
 526                                 | BATL_CACHEINHIBIT \
 527                                 | BATL_GUARDEDSTORAGE)
 528 #define CONFIG_SYS_IBAT7U       (CONFIG_SYS_PCI1_MMIO_PHYS \
 529                                 | BATU_BL_256M \
 530                                 | BATU_VS \
 531                                 | BATU_VP)
 532 #define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
 533 #define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
 534 #else /* CONFIG_PCI */
 535 #define CONFIG_SYS_IBAT6L       (0)
 536 #define CONFIG_SYS_IBAT6U       (0)
 537 #define CONFIG_SYS_IBAT7L       (0)
 538 #define CONFIG_SYS_IBAT7U       (0)
 539 #define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
 540 #define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
 541 #define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
 542 #define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
 543 #endif /* CONFIG_PCI */
 544
 545 #if defined(CONFIG_CMD_KGDB)
 546 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 547 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 548 #endif
 549
 550 /*
 551  * Environment Configuration
 552  */
 553 #define CONFIG_ENV_OVERWRITE
 554
 555 #if defined(CONFIG_UEC_ETH)
 556 #define CONFIG_HAS_ETH0
 557 #define CONFIG_HAS_ETH1
 558 #define CONFIG_HAS_ETH2
 559 #define CONFIG_HAS_ETH3
 560 #endif
 561
 562 #define CONFIG_BAUDRATE 115200
 563
 564 #define CONFIG_LOADADDR a00000
 565 #define CONFIG_HOSTNAME mpc8360erdk
 566 #define CONFIG_BOOTFILE "uImage"
 567
 568 #define CONFIG_ROOTPATH         "/nfsroot/"
 569
 570 #define CONFIG_BOOTDELAY 2      /* -1 disables auto-boot */
 571 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */
 572
 573 #define CONFIG_EXTRA_ENV_SETTINGS \
 574         "netdev=eth0\0"                                                 \
 575         "consoledev=ttyS0\0"                                            \
 576         "loadaddr=a00000\0"                                             \
 577         "fdtaddr=900000\0"                                              \
 578         "fdtfile=mpc836x_rdk.dtb\0"                                     \
 579         "fsfile=fs\0"                                                   \
 580         "ubootfile=u-boot.bin\0"                                        \
 581         "mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),"\
 582                                                         "-(rootfs)\0"   \
 583         "setbootargs=setenv bootargs console=$consoledev,$baudrate "    \
 584                 "$mtdparts panic=1\0"                                   \
 585         "adddhcpargs=setenv bootargs $bootargs ip=on\0"                 \
 586         "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:"    \
 587                 "$gatewayip:$netmask:$hostname:$netdev:off "            \
 588                 "root=/dev/nfs rw nfsroot=$serverip:$rootpath\0"        \
 589         "addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 "    \
 590                 "rootfstype=jffs2 rw\0"                                 \
 591         "tftp_get_uboot=tftp 100000 $ubootfile\0"                       \
 592         "tftp_get_kernel=tftp $loadaddr $bootfile\0"                    \
 593         "tftp_get_dtb=tftp $fdtaddr $fdtfile\0"                         \
 594         "tftp_get_fs=tftp c00000 $fsfile\0"                             \
 595         "nand_erase_kernel=nand erase 0 400000\0"                       \
 596         "nand_erase_dtb=nand erase 400000 20000\0"                      \
 597         "nand_erase_fs=nand erase 420000 3be0000\0"                     \
 598         "nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0"       \
 599         "nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0"       \
 600         "nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0"      \
 601         "nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0"         \
 602         "nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0"         \
 603         "nor_reflash=protect off ff800000 ff87ffff ; "                  \
 604                 "erase ff800000 ff87ffff ; "                            \
 605                 "cp.b 100000 ff800000 $filesize\0"                      \
 606         "nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel "    \
 607                 "nand_write_kernel\0"                                   \
 608         "nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\
 609         "nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0" \
 610         "nand_reflash=run nand_reflash_kernel nand_reflash_dtb "        \
 611                 "nand_reflash_fs\0"                                     \
 612         "boot_m=bootm $loadaddr - $fdtaddr\0"                           \
 613         "dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\
 614         "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\
 615                 "boot_m\0"                                              \
 616         "nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\
 617                 "boot_m\0"                                              \
 618         ""
 619
 620 #define CONFIG_BOOTCOMMAND "run dhcpboot"
 621
 622 #endif /* __CONFIG_H */