2 * Copyright (C) 2006 Freescale Semiconductor, Inc.
4 * Dave Liu <daveliu@freescale.com>
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License as
8 * published by the Free Software Foundation; either version 2 of
9 * the License, or (at your option) any later version.
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
26 * High Level Configuration Options
28 #define CONFIG_E300 1 /* E300 family */
29 #define CONFIG_QE 1 /* Has QE */
30 #define CONFIG_MPC83xx 1 /* MPC83xx family */
31 #define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
32 #define CONFIG_MPC8360EMDS 1 /* MPC8360EMDS board specific */
34 #define CONFIG_SYS_TEXT_BASE 0xFE000000
36 #undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */
37 #undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */
42 #ifdef CONFIG_PCISLAVE
43 #define CONFIG_83XX_PCICLK 66000000 /* in HZ */
45 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */
48 #ifndef CONFIG_SYS_CLK_FREQ
49 #define CONFIG_SYS_CLK_FREQ 66000000
53 * Hardware Reset Configuration Word
55 #define CONFIG_SYS_HRCW_LOW (\
56 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
57 HRCWL_DDR_TO_SCB_CLK_1X1 |\
58 HRCWL_CSB_TO_CLKIN_4X1 |\
60 HRCWL_CE_PLL_VCO_DIV_4 |\
61 HRCWL_CE_PLL_DIV_1X1 |\
62 HRCWL_CE_TO_PLL_1X6 |\
63 HRCWL_CORE_TO_CSB_2X1)
65 #ifdef CONFIG_PCISLAVE
66 #define CONFIG_SYS_HRCW_HIGH (\
68 HRCWH_PCI1_ARBITER_DISABLE |\
69 HRCWH_PCICKDRV_DISABLE |\
71 HRCWH_FROM_0XFFF00100 |\
72 HRCWH_BOOTSEQ_DISABLE |\
73 HRCWH_SW_WATCHDOG_DISABLE |\
74 HRCWH_ROM_LOC_LOCAL_16BIT)
76 #define CONFIG_SYS_HRCW_HIGH (\
78 HRCWH_PCI1_ARBITER_ENABLE |\
79 HRCWH_PCICKDRV_ENABLE |\
81 HRCWH_FROM_0X00000100 |\
82 HRCWH_BOOTSEQ_DISABLE |\
83 HRCWH_SW_WATCHDOG_DISABLE |\
84 HRCWH_ROM_LOC_LOCAL_16BIT)
90 #define CONFIG_SYS_SICRH 0x00000000
91 #define CONFIG_SYS_SICRL 0x40000000
93 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
94 #define CONFIG_BOARD_EARLY_INIT_R
99 #define CONFIG_SYS_IMMR 0xE0000000
104 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
105 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
107 #define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000)
108 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
109 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
110 | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
112 #define CONFIG_SYS_83XX_DDR_USES_CS0
114 #define CONFIG_DDR_ECC /* support DDR ECC function */
115 #define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
118 * DDRCDR - DDR Control Driver Register
120 #define CONFIG_SYS_DDRCDR_VALUE 0x80080001
122 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
123 #if defined(CONFIG_SPD_EEPROM)
125 * Determine DDR configuration from I2C interface.
127 #define SPD_EEPROM_ADDRESS 0x52 /* DDR SODIMM */
130 * Manually set up DDR parameters
132 #define CONFIG_SYS_DDR_SIZE 256 /* MB */
133 #if defined(CONFIG_DDR_II)
134 #define CONFIG_SYS_DDRCDR 0x80080001
135 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
136 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80330102
137 #define CONFIG_SYS_DDR_TIMING_0 0x00220802
138 #define CONFIG_SYS_DDR_TIMING_1 0x38357322
139 #define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8
140 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
141 #define CONFIG_SYS_DDR_CLK_CNTL 0x02000000
142 #define CONFIG_SYS_DDR_MODE 0x47d00432
143 #define CONFIG_SYS_DDR_MODE2 0x8000c000
144 #define CONFIG_SYS_DDR_INTERVAL 0x03cf0080
145 #define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000
146 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
148 #define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN \
149 | CSCONFIG_ROW_BIT_13 \
150 | CSCONFIG_COL_BIT_9)
151 #define CONFIG_SYS_DDR_TIMING_1 0x37344321 /* tCL-tRCD-tRP-tRAS=2.5-3-3-7 */
152 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* may need tuning */
153 #define CONFIG_SYS_DDR_CONTROL 0x42008000 /* Self refresh,2T timing */
154 #define CONFIG_SYS_DDR_MODE 0x20000162 /* DLL,normal,seq,4/2.5 */
155 #define CONFIG_SYS_DDR_INTERVAL 0x045b0100 /* page mode */
162 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
163 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
164 #define CONFIG_SYS_MEMTEST_END 0x00100000
167 * The reserved memory
170 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
172 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
173 #define CONFIG_SYS_RAMBOOT
175 #undef CONFIG_SYS_RAMBOOT
178 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
179 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
180 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
183 * Initial RAM Base Address Setup
185 #define CONFIG_SYS_INIT_RAM_LOCK 1
186 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
187 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
188 #define CONFIG_SYS_GBL_DATA_OFFSET \
189 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
192 * Local Bus Configuration & Clock Setup
194 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
195 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
196 #define CONFIG_SYS_LBC_LBCR 0x00000000
199 * FLASH on the Local Bus
201 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
202 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
203 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
204 #define CONFIG_SYS_FLASH_SIZE 32 /* max FLASH size is 32M */
205 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
206 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
208 /* Window base at flash base */
209 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
210 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
212 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
213 | BR_PS_16 /* 16 bit port */ \
214 | BR_MS_GPCM /* MSEL = GPCM */ \
216 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
226 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
227 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
229 #undef CONFIG_SYS_FLASH_CHECKSUM
232 * BCSR on the Local Bus
234 #define CONFIG_SYS_BCSR 0xF8000000
235 /* Access window base at BCSR base */
236 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR
237 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_64KB)
239 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \
243 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \
254 * SDRAM on the Local Bus
256 #define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */
257 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
259 #define CONFIG_SYS_LB_SDRAM /* if board has SRDAM on local bus */
261 #ifdef CONFIG_SYS_LB_SDRAM
262 #define CONFIG_SYS_LBLAWBAR2 0
263 #define CONFIG_SYS_LBLAWAR2 (LBLAWAR_EN | LBLAWAR_64MB)
265 /*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
267 * Base Register 2 and Option Register 2 configure SDRAM.
270 * Base address = BR[0:16] = dynamic
271 * port size = 32-bits = BR2[19:20] = 11
272 * no parity checking = BR2[21:22] = 00
273 * SDRAM for MSEL = BR2[24:26] = 011
276 * 0 4 8 12 16 20 24 28
277 * xxxx xxxx xxxx xxxx x001 1000 0110 0001 = 00001861
280 /* Port size=32bit, MSEL=DRAM */
281 #define CONFIG_SYS_BR2 (BR_PS_32 | BR_MS_SDRAM | BR_V) /* 0xF0001861 */
284 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
287 * 64MB mask for AM, OR2[0:7] = 1111 1100
288 * XAM, OR2[17:18] = 11
289 * 9 columns OR2[19-21] = 010
290 * 13 rows OR2[23-25] = 100
291 * EAD set for extra time OR[31] = 1
293 * 0 4 8 12 16 20 24 28
294 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
297 #define CONFIG_SYS_OR2 (MEG_TO_AM(CONFIG_SYS_LBC_SDRAM_SIZE) \
299 | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
300 | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
304 /* LB sdram refresh timer, about 6us */
305 #define CONFIG_SYS_LBC_LSRT 0x32000000
306 /* LB refresh timer prescal, 266MHz/32 */
307 #define CONFIG_SYS_LBC_MRTPR 0x20000000
309 #define CONFIG_SYS_LBC_LSDMR_COMMON 0x0063b723
312 * SDRAM Controller configuration sequence.
314 #define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
315 #define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
316 #define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
317 #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
318 #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
323 * Windows to access Platform I/O Boards (PIB) via local bus
325 #define CONFIG_SYS_PIB_BASE 0xF8008000
326 #define CONFIG_SYS_PIB_WINDOW_SIZE (32 * 1024)
328 /* [RFC] This LBLAW only covers the 2nd window (CS5) */
329 #define CONFIG_SYS_LBLAWBAR3_PRELIM \
330 CONFIG_SYS_PIB_BASE + CONFIG_SYS_PIB_WINDOW_SIZE
331 #define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
334 * CS4 on Local Bus, to PIB
336 /* CS4 base address at 0xf8008000 */
337 #define CONFIG_SYS_BR4_PRELIM (CONFIG_SYS_PIB_BASE \
342 #define CONFIG_SYS_OR4_PRELIM (OR_AM_32KB \
353 * CS5 on Local Bus, to PIB
355 /* CS5 base address at 0xf8010000 */
356 #define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_PIB_BASE + \
357 CONFIG_SYS_PIB_WINDOW_SIZE) \
362 #define CONFIG_SYS_OR5_PRELIM (CONFIG_SYS_PIB_BASE \
375 #define CONFIG_CONS_INDEX 1
376 #define CONFIG_SYS_NS16550
377 #define CONFIG_SYS_NS16550_SERIAL
378 #define CONFIG_SYS_NS16550_REG_SIZE 1
379 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
381 #define CONFIG_SYS_BAUDRATE_TABLE \
382 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
384 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
385 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
387 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */
388 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */
389 /* Use the HUSH parser */
390 #define CONFIG_SYS_HUSH_PARSER
391 #ifdef CONFIG_SYS_HUSH_PARSER
392 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
395 /* pass open firmware flat tree */
396 #define CONFIG_OF_LIBFDT 1
397 #define CONFIG_OF_BOARD_SETUP 1
398 #define CONFIG_OF_STDOUT_VIA_ALIAS 1
401 #define CONFIG_HARD_I2C /* I2C with hardware support */
402 #undef CONFIG_SOFT_I2C /* I2C bit-banged */
403 #define CONFIG_FSL_I2C
404 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
405 #define CONFIG_SYS_I2C_SLAVE 0x7F
406 #define CONFIG_SYS_I2C_NOPROBES {0x52} /* Don't probe these addrs */
407 #define CONFIG_SYS_I2C_OFFSET 0x3000
408 #define CONFIG_SYS_I2C2_OFFSET 0x3100
411 * Config on-board RTC
413 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
414 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
418 * Addresses are mapped 1-1.
420 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
421 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
422 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
423 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
424 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
425 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
426 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000
427 #define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000
428 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */
430 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
431 #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
432 #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
437 #define CONFIG_PCI_PNP /* do pci plug-and-play */
438 #define CONFIG_83XX_PCI_STREAMING
440 #undef CONFIG_EEPRO100
441 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
442 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
444 #endif /* CONFIG_PCI */
447 #define CONFIG_HWCONFIG 1
450 * QE UEC ethernet configuration
452 #define CONFIG_UEC_ETH
453 #define CONFIG_ETHPRIME "UEC0"
454 #define CONFIG_PHY_MODE_NEED_CHANGE
456 #define CONFIG_UEC_ETH1 /* GETH1 */
458 #ifdef CONFIG_UEC_ETH1
459 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
460 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE
461 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK9
462 #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
463 #define CONFIG_SYS_UEC1_PHY_ADDR 0
464 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
465 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
468 #define CONFIG_UEC_ETH2 /* GETH2 */
470 #ifdef CONFIG_UEC_ETH2
471 #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
472 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE
473 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK4
474 #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
475 #define CONFIG_SYS_UEC2_PHY_ADDR 1
476 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
477 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
484 #ifndef CONFIG_SYS_RAMBOOT
485 #define CONFIG_ENV_IS_IN_FLASH 1
486 #define CONFIG_ENV_ADDR \
487 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
488 #define CONFIG_ENV_SECT_SIZE 0x20000
489 #define CONFIG_ENV_SIZE 0x2000
491 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
492 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
493 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
494 #define CONFIG_ENV_SIZE 0x2000
497 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
498 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
503 #define CONFIG_BOOTP_BOOTFILESIZE
504 #define CONFIG_BOOTP_BOOTPATH
505 #define CONFIG_BOOTP_GATEWAY
506 #define CONFIG_BOOTP_HOSTNAME
510 * Command line configuration.
512 #include <config_cmd_default.h>
514 #define CONFIG_CMD_PING
515 #define CONFIG_CMD_I2C
516 #define CONFIG_CMD_ASKENV
517 #define CONFIG_CMD_SDRAM
519 #if defined(CONFIG_PCI)
520 #define CONFIG_CMD_PCI
523 #if defined(CONFIG_SYS_RAMBOOT)
524 #undef CONFIG_CMD_SAVEENV
525 #undef CONFIG_CMD_LOADS
529 #undef CONFIG_WATCHDOG /* watchdog disabled */
532 * Miscellaneous configurable options
534 #define CONFIG_SYS_LONGHELP /* undef to save memory */
535 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
536 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
538 #if defined(CONFIG_CMD_KGDB)
539 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
541 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
544 /* Print Buffer Size */
545 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
546 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
547 /* Boot Argument Buffer Size */
548 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
549 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
552 * For booting Linux, the board info and command line data
553 * have to be in the first 256 MB of memory, since this is
554 * the maximum mapped by the Linux kernel during initialization.
556 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
561 #define CONFIG_SYS_HID0_INIT 0x000000000
562 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
563 HID0_ENABLE_INSTRUCTION_CACHE)
564 #define CONFIG_SYS_HID2 HID2_HBE
570 #define CONFIG_HIGH_BATS 1 /* High BATs supported */
572 /* DDR/LBC SDRAM: cacheable */
573 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
576 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
580 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
581 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
583 /* IMMRBAR & PCI IO: cache-inhibit and guarded */
584 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \
586 | BATL_CACHEINHIBIT \
587 | BATL_GUARDEDSTORAGE)
588 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \
592 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
593 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
595 /* BCSR: cache-inhibit and guarded */
596 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR \
598 | BATL_CACHEINHIBIT \
599 | BATL_GUARDEDSTORAGE)
600 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR \
604 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
605 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
607 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
608 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \
611 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \
615 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \
617 | BATL_CACHEINHIBIT \
618 | BATL_GUARDEDSTORAGE)
619 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
621 /* DDR/LBC SDRAM next 256M: cacheable */
622 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM_BASE2 \
625 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM_BASE2 \
629 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
630 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
632 /* Stack in dcache: cacheable, no memory coherence */
633 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
634 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \
638 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
639 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
642 /* PCI MEM space: cacheable */
643 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \
646 #define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \
650 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
651 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
652 /* PCI MMIO space: cache-inhibit and guarded */
653 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \
655 | BATL_CACHEINHIBIT \
656 | BATL_GUARDEDSTORAGE)
657 #define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \
661 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
662 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
664 #define CONFIG_SYS_IBAT6L (0)
665 #define CONFIG_SYS_IBAT6U (0)
666 #define CONFIG_SYS_IBAT7L (0)
667 #define CONFIG_SYS_IBAT7U (0)
668 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
669 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
670 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
671 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
674 #if defined(CONFIG_CMD_KGDB)
675 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
676 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
680 * Environment Configuration
683 #define CONFIG_ENV_OVERWRITE
685 #if defined(CONFIG_UEC_ETH)
686 #define CONFIG_HAS_ETH0
687 #define CONFIG_HAS_ETH1
690 #define CONFIG_BAUDRATE 115200
692 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
694 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
695 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
697 #define CONFIG_EXTRA_ENV_SETTINGS \
699 "consoledev=ttyS0\0" \
700 "ramdiskaddr=1000000\0" \
701 "ramdiskfile=ramfs.83xx\0" \
703 "fdtfile=mpc836x_mds.dtb\0" \
706 #define CONFIG_NFSBOOTCOMMAND \
707 "setenv bootargs root=/dev/nfs rw " \
708 "nfsroot=$serverip:$rootpath " \
709 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
711 "console=$consoledev,$baudrate $othbootargs;" \
712 "tftp $loadaddr $bootfile;" \
713 "tftp $fdtaddr $fdtfile;" \
714 "bootm $loadaddr - $fdtaddr"
716 #define CONFIG_RAMBOOTCOMMAND \
717 "setenv bootargs root=/dev/ram rw " \
718 "console=$consoledev,$baudrate $othbootargs;" \
719 "tftp $ramdiskaddr $ramdiskfile;" \
720 "tftp $loadaddr $bootfile;" \
721 "tftp $fdtaddr $fdtfile;" \
722 "bootm $loadaddr $ramdiskaddr $fdtaddr"
725 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
727 #endif /* __CONFIG_H */