include/configs/MPC8313ERDB_NOR.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) Freescale Semiconductor, Inc. 2006, 2010.
   4  */
   5 /*
   6  * mpc8313epb board configuration file
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15 #define CONFIG_E300             1
  16
  17 #ifndef CONFIG_SYS_MONITOR_BASE
  18 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  19 #endif
  20
  21 #define CONFIG_PCI_INDIRECT_BRIDGE
  22
  23 /*
  24  * On-board devices
  25  *
  26  * TSEC1 is VSC switch
  27  * TSEC2 is SoC TSEC
  28  */
  29 #define CONFIG_VSC7385_ENET
  30 #define CONFIG_TSEC2
  31
  32 /* Early revs of this board will lock up hard when attempting
  33  * to access the PMC registers, unless a JTAG debugger is
  34  * connected, or some resistor modifications are made.
  35  */
  36 #define CONFIG_SYS_8313ERDB_BROKEN_PMC 1
  37
  38 /*
  39  * Device configurations
  40  */
  41
  42 /* Vitesse 7385 */
  43
  44 #ifdef CONFIG_VSC7385_ENET
  45
  46 #define CONFIG_TSEC1
  47
  48 /* The flash address and size of the VSC7385 firmware image */
  49 #define CONFIG_VSC7385_IMAGE            0xFE7FE000
  50 #define CONFIG_VSC7385_IMAGE_SIZE       8192
  51
  52 #endif
  53
  54 /*
  55  * DDR Setup
  56  */
  57 #define CONFIG_SYS_SDRAM_BASE           0x00000000 /* DDR is system memory*/
  58
  59 /*
  60  * Manually set up DDR parameters, as this board does not
  61  * seem to have the SPD connected to I2C.
  62  */
  63 #define CONFIG_SYS_DDR_SIZE     128             /* MB */
  64 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
  65                                 | CSCONFIG_ODT_RD_NEVER \
  66                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
  67                                 | CSCONFIG_ROW_BIT_13 \
  68                                 | CSCONFIG_COL_BIT_10)
  69                                 /* 0x80010102 */
  70
  71 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
  72 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
  73                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
  74                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
  75                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
  76                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
  77                                 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
  78                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
  79                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
  80                                 /* 0x00220802 */
  81 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
  82                                 | (8 << TIMING_CFG1_ACTTOPRE_SHIFT) \
  83                                 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
  84                                 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
  85                                 | (10 << TIMING_CFG1_REFREC_SHIFT) \
  86                                 | (3 << TIMING_CFG1_WRREC_SHIFT) \
  87                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
  88                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
  89                                 /* 0x3835a322 */
  90 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
  91                                 | (5 << TIMING_CFG2_CPO_SHIFT) \
  92                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
  93                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
  94                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
  95                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
  96                                 | (6 << TIMING_CFG2_FOUR_ACT_SHIFT))
  97                                 /* 0x129048c6 */ /* P9-45,may need tuning */
  98 #define CONFIG_SYS_DDR_INTERVAL ((1296 << SDRAM_INTERVAL_REFINT_SHIFT) \
  99                                 | (1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 100                                 /* 0x05100500 */
 101 #if defined(CONFIG_DDR_2T_TIMING)
 102 #define CONFIG_SYS_SDRAM_CFG    (SDRAM_CFG_SREN \
 103                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 104                                 | SDRAM_CFG_DBW_32 \
 105                                 | SDRAM_CFG_2T_EN)
 106                                 /* 0x43088000 */
 107 #else
 108 #define CONFIG_SYS_SDRAM_CFG    (SDRAM_CFG_SREN \
 109                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 110                                 | SDRAM_CFG_DBW_32)
 111                                 /* 0x43080000 */
 112 #endif
 113 #define CONFIG_SYS_SDRAM_CFG2           0x00401000
 114 /* set burst length to 8 for 32-bit data path */
 115 #define CONFIG_SYS_DDR_MODE     ((0x4448 << SDRAM_MODE_ESD_SHIFT) \
 116                                 | (0x0632 << SDRAM_MODE_SD_SHIFT))
 117                                 /* 0x44480632 */
 118 #define CONFIG_SYS_DDR_MODE_2   0x8000C000
 119
 120 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 121                                 /*0x02000000*/
 122 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 123                                 | DDRCDR_PZ_NOMZ \
 124                                 | DDRCDR_NZ_NOMZ \
 125                                 | DDRCDR_M_ODR)
 126
 127 /*
 128  * FLASH on the Local Bus
 129  */
 130 #define CONFIG_SYS_FLASH_BASE           0xFE000000      /* start of FLASH   */
 131 #define CONFIG_SYS_FLASH_SIZE           8       /* flash size in MB */
 132 #define CONFIG_SYS_FLASH_PROTECTION     1       /* Use h/w Flash protection. */
 133 #define CONFIG_SYS_FLASH_EMPTY_INFO             /* display empty sectors */
 134
 135 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 136 #define CONFIG_SYS_MAX_FLASH_SECT       135     /* sectors per device */
 137
 138 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 139 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 140
 141 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && \
 142         !defined(CONFIG_SPL_BUILD)
 143 #define CONFIG_SYS_RAMBOOT
 144 #endif
 145
 146 #define CONFIG_SYS_INIT_RAM_LOCK        1
 147 #define CONFIG_SYS_INIT_RAM_ADDR        0xFD000000      /* Initial RAM addr */
 148 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* Size of used area in RAM*/
 149
 150 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 151                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 152 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 153
 154 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
 155 #define CONFIG_SYS_MONITOR_LEN  (512 * 1024)    /* Reserve 512 kB for Mon */
 156 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024)    /* Reserved for malloc */
 157
 158 /* drivers/mtd/nand/nand.c */
 159 #define CONFIG_SYS_NAND_BASE            0xE2800000
 160
 161 #define CONFIG_MTD_PARTITION
 162
 163 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 164 #define CONFIG_NAND_FSL_ELBC 1
 165 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384
 166 #define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024)
 167
 168 /* Still needed for spl_minimal.c */
 169 #define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
 170 #define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
 171
 172 /* local bus write LED / read status buffer (BCSR) mapping */
 173 #define CONFIG_SYS_BCSR_ADDR            0xFA000000
 174 #define CONFIG_SYS_BCSR_SIZE            (32 * 1024)     /* 0x00008000 */
 175                                         /* map at 0xFA000000 on LCS3 */
 176 /* Vitesse 7385 */
 177
 178 #ifdef CONFIG_VSC7385_ENET
 179
 180                                         /* VSC7385 Base address on LCS2 */
 181 #define CONFIG_SYS_VSC7385_BASE         0xF0000000
 182 #define CONFIG_SYS_VSC7385_SIZE         (128 * 1024)    /* 0x00020000 */
 183
 184
 185 #endif
 186
 187 #define CONFIG_MPC83XX_GPIO 1
 188
 189 /*
 190  * Serial Port
 191  */
 192 #define CONFIG_SYS_NS16550_SERIAL
 193 #define CONFIG_SYS_NS16550_REG_SIZE     1
 194
 195 #define CONFIG_SYS_BAUDRATE_TABLE       \
 196         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 197
 198 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 199 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 200
 201 /* I2C */
 202 #define CONFIG_SYS_I2C
 203 #define CONFIG_SYS_I2C_FSL
 204 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 205 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 206 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 207 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 208 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 209 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 210 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 211
 212 /*
 213  * General PCI
 214  * Addresses are mapped 1-1.
 215  */
 216 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 217 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 218 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
 219 #define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 220 #define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 221 #define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000      /* 256M */
 222 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000
 223 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
 224 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000      /* 1M */
 225
 226 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057   /* Motorola */
 227
 228 /*
 229  * TSEC
 230  */
 231
 232 #define CONFIG_GMII                     /* MII PHY management */
 233
 234 #ifdef CONFIG_TSEC1
 235 #define CONFIG_HAS_ETH0
 236 #define CONFIG_TSEC1_NAME       "TSEC0"
 237 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 238 #define TSEC1_PHY_ADDR          0x1c
 239 #define TSEC1_FLAGS             TSEC_GIGABIT
 240 #define TSEC1_PHYIDX            0
 241 #endif
 242
 243 #ifdef CONFIG_TSEC2
 244 #define CONFIG_HAS_ETH1
 245 #define CONFIG_TSEC2_NAME       "TSEC1"
 246 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 247 #define TSEC2_PHY_ADDR          4
 248 #define TSEC2_FLAGS             TSEC_GIGABIT
 249 #define TSEC2_PHYIDX            0
 250 #endif
 251
 252 /* Options are: TSEC[0-1] */
 253 #define CONFIG_ETHPRIME                 "TSEC1"
 254
 255 /*
 256  * Configure on-board RTC
 257  */
 258 #define CONFIG_RTC_DS1337
 259 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 260
 261 /*
 262  * Environment
 263  */
 264 #if !defined(CONFIG_SYS_RAMBOOT)
 265 /* Address and size of Redundant Environment Sector */
 266 #endif
 267
 268 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 269 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 270
 271 /*
 272  * BOOTP options
 273  */
 274 #define CONFIG_BOOTP_BOOTFILESIZE
 275
 276 /*
 277  * Command line configuration.
 278  */
 279
 280 /*
 281  * Miscellaneous configurable options
 282  */
 283 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 284 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 285
 286                                 /* Boot Argument Buffer Size */
 287 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 288
 289 /*
 290  * For booting Linux, the board info and command line data
 291  * have to be in the first 256 MB of memory, since this is
 292  * the maximum mapped by the Linux kernel during initialization.
 293  */
 294                                 /* Initial Memory map for Linux*/
 295 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)
 296 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 297
 298 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000      /* PCIHOST  */
 299
 300 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
 301
 302 /* System IO Config */
 303 #define CONFIG_SYS_SICRH        (SICRH_TSOBI1 | SICRH_TSOBI2)   /* RGMII */
 304                         /* Enable Internal USB Phy and GPIO on LCD Connector */
 305 #define CONFIG_SYS_SICRL        (SICRL_USBDR_10 | SICRL_LBC)
 306
 307 /*
 308  * Environment Configuration
 309  */
 310 #define CONFIG_ENV_OVERWRITE
 311
 312 #define CONFIG_NETDEV           "eth1"
 313
 314 #define CONFIG_HOSTNAME         "mpc8313erdb"
 315 #define CONFIG_ROOTPATH         "/nfs/root/path"
 316 #define CONFIG_BOOTFILE         "uImage"
 317                                 /* U-Boot image on TFTP server */
 318 #define CONFIG_UBOOTPATH        "u-boot.bin"
 319 #define CONFIG_FDTFILE          "mpc8313erdb.dtb"
 320
 321                                 /* default location for tftp and bootm */
 322 #define CONFIG_LOADADDR         800000
 323
 324 #define CONFIG_EXTRA_ENV_SETTINGS \
 325         "netdev=" CONFIG_NETDEV "\0"                                    \
 326         "ethprime=TSEC1\0"                                              \
 327         "uboot=" CONFIG_UBOOTPATH "\0"                                  \
 328         "tftpflash=tftpboot $loadaddr $uboot; "                         \
 329                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 330                         " +$filesize; " \
 331                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 332                         " +$filesize; " \
 333                 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
 334                         " $filesize; "  \
 335                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 336                         " +$filesize; " \
 337                 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
 338                         " $filesize\0"  \
 339         "fdtaddr=780000\0"                                              \
 340         "fdtfile=" CONFIG_FDTFILE "\0"                                  \
 341         "console=ttyS0\0"                                               \
 342         "setbootargs=setenv bootargs "                                  \
 343                 "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
 344         "setipargs=setenv bootargs nfsroot=$serverip:$rootpath "         \
 345                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"\
 346                                                         "$netdev:off " \
 347                 "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
 348
 349 #define CONFIG_NFSBOOTCOMMAND                                           \
 350         "setenv rootdev /dev/nfs;"                                      \
 351         "run setbootargs;"                                              \
 352         "run setipargs;"                                                \
 353         "tftp $loadaddr $bootfile;"                                     \
 354         "tftp $fdtaddr $fdtfile;"                                       \
 355         "bootm $loadaddr - $fdtaddr"
 356
 357 #define CONFIG_RAMBOOTCOMMAND                                           \
 358         "setenv rootdev /dev/ram;"                                      \
 359         "run setbootargs;"                                              \
 360         "tftp $ramdiskaddr $ramdiskfile;"                               \
 361         "tftp $loadaddr $bootfile;"                                     \
 362         "tftp $fdtaddr $fdtfile;"                                       \
 363         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 364
 365 #endif  /* __CONFIG_H */