include/configs/MPC8313ERDB_NOR.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) Freescale Semiconductor, Inc. 2006, 2010.
   4  */
   5 /*
   6  * mpc8313epb board configuration file
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15 #define CONFIG_E300             1
  16
  17 #ifndef CONFIG_SYS_MONITOR_BASE
  18 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  19 #endif
  20
  21 #define CONFIG_PCI_INDIRECT_BRIDGE
  22 #define CONFIG_FSL_ELBC 1
  23
  24 /*
  25  * On-board devices
  26  *
  27  * TSEC1 is VSC switch
  28  * TSEC2 is SoC TSEC
  29  */
  30 #define CONFIG_VSC7385_ENET
  31 #define CONFIG_TSEC2
  32
  33 #define CONFIG_SYS_MEMTEST_START        0x00001000
  34 #define CONFIG_SYS_MEMTEST_END          0x07f00000
  35
  36 /* Early revs of this board will lock up hard when attempting
  37  * to access the PMC registers, unless a JTAG debugger is
  38  * connected, or some resistor modifications are made.
  39  */
  40 #define CONFIG_SYS_8313ERDB_BROKEN_PMC 1
  41
  42 /*
  43  * Device configurations
  44  */
  45
  46 /* Vitesse 7385 */
  47
  48 #ifdef CONFIG_VSC7385_ENET
  49
  50 #define CONFIG_TSEC1
  51
  52 /* The flash address and size of the VSC7385 firmware image */
  53 #define CONFIG_VSC7385_IMAGE            0xFE7FE000
  54 #define CONFIG_VSC7385_IMAGE_SIZE       8192
  55
  56 #endif
  57
  58 /*
  59  * DDR Setup
  60  */
  61 #define CONFIG_SYS_SDRAM_BASE           0x00000000 /* DDR is system memory*/
  62
  63 /*
  64  * Manually set up DDR parameters, as this board does not
  65  * seem to have the SPD connected to I2C.
  66  */
  67 #define CONFIG_SYS_DDR_SIZE     128             /* MB */
  68 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
  69                                 | CSCONFIG_ODT_RD_NEVER \
  70                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
  71                                 | CSCONFIG_ROW_BIT_13 \
  72                                 | CSCONFIG_COL_BIT_10)
  73                                 /* 0x80010102 */
  74
  75 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
  76 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
  77                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
  78                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
  79                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
  80                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
  81                                 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
  82                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
  83                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
  84                                 /* 0x00220802 */
  85 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
  86                                 | (8 << TIMING_CFG1_ACTTOPRE_SHIFT) \
  87                                 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
  88                                 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
  89                                 | (10 << TIMING_CFG1_REFREC_SHIFT) \
  90                                 | (3 << TIMING_CFG1_WRREC_SHIFT) \
  91                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
  92                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
  93                                 /* 0x3835a322 */
  94 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
  95                                 | (5 << TIMING_CFG2_CPO_SHIFT) \
  96                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
  97                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
  98                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
  99                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 100                                 | (6 << TIMING_CFG2_FOUR_ACT_SHIFT))
 101                                 /* 0x129048c6 */ /* P9-45,may need tuning */
 102 #define CONFIG_SYS_DDR_INTERVAL ((1296 << SDRAM_INTERVAL_REFINT_SHIFT) \
 103                                 | (1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 104                                 /* 0x05100500 */
 105 #if defined(CONFIG_DDR_2T_TIMING)
 106 #define CONFIG_SYS_SDRAM_CFG    (SDRAM_CFG_SREN \
 107                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 108                                 | SDRAM_CFG_DBW_32 \
 109                                 | SDRAM_CFG_2T_EN)
 110                                 /* 0x43088000 */
 111 #else
 112 #define CONFIG_SYS_SDRAM_CFG    (SDRAM_CFG_SREN \
 113                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 114                                 | SDRAM_CFG_DBW_32)
 115                                 /* 0x43080000 */
 116 #endif
 117 #define CONFIG_SYS_SDRAM_CFG2           0x00401000
 118 /* set burst length to 8 for 32-bit data path */
 119 #define CONFIG_SYS_DDR_MODE     ((0x4448 << SDRAM_MODE_ESD_SHIFT) \
 120                                 | (0x0632 << SDRAM_MODE_SD_SHIFT))
 121                                 /* 0x44480632 */
 122 #define CONFIG_SYS_DDR_MODE_2   0x8000C000
 123
 124 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 125                                 /*0x02000000*/
 126 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 127                                 | DDRCDR_PZ_NOMZ \
 128                                 | DDRCDR_NZ_NOMZ \
 129                                 | DDRCDR_M_ODR)
 130
 131 /*
 132  * FLASH on the Local Bus
 133  */
 134 #define CONFIG_SYS_FLASH_BASE           0xFE000000      /* start of FLASH   */
 135 #define CONFIG_SYS_FLASH_SIZE           8       /* flash size in MB */
 136 #define CONFIG_SYS_FLASH_PROTECTION     1       /* Use h/w Flash protection. */
 137 #define CONFIG_SYS_FLASH_EMPTY_INFO             /* display empty sectors */
 138
 139 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 140 #define CONFIG_SYS_MAX_FLASH_SECT       135     /* sectors per device */
 141
 142 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 143 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 144
 145 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && \
 146         !defined(CONFIG_SPL_BUILD)
 147 #define CONFIG_SYS_RAMBOOT
 148 #endif
 149
 150 #define CONFIG_SYS_INIT_RAM_LOCK        1
 151 #define CONFIG_SYS_INIT_RAM_ADDR        0xFD000000      /* Initial RAM addr */
 152 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* Size of used area in RAM*/
 153
 154 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 155                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 156 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 157
 158 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
 159 #define CONFIG_SYS_MONITOR_LEN  (512 * 1024)    /* Reserve 512 kB for Mon */
 160 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024)    /* Reserved for malloc */
 161
 162 /* drivers/mtd/nand/nand.c */
 163 #define CONFIG_SYS_NAND_BASE            0xE2800000
 164
 165 #define CONFIG_MTD_PARTITION
 166
 167 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 168 #define CONFIG_NAND_FSL_ELBC 1
 169 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384
 170 #define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024)
 171
 172 /* Still needed for spl_minimal.c */
 173 #define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
 174 #define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
 175
 176 /* local bus write LED / read status buffer (BCSR) mapping */
 177 #define CONFIG_SYS_BCSR_ADDR            0xFA000000
 178 #define CONFIG_SYS_BCSR_SIZE            (32 * 1024)     /* 0x00008000 */
 179                                         /* map at 0xFA000000 on LCS3 */
 180 /* Vitesse 7385 */
 181
 182 #ifdef CONFIG_VSC7385_ENET
 183
 184                                         /* VSC7385 Base address on LCS2 */
 185 #define CONFIG_SYS_VSC7385_BASE         0xF0000000
 186 #define CONFIG_SYS_VSC7385_SIZE         (128 * 1024)    /* 0x00020000 */
 187
 188
 189 #endif
 190
 191 #define CONFIG_MPC83XX_GPIO 1
 192
 193 /*
 194  * Serial Port
 195  */
 196 #define CONFIG_SYS_NS16550_SERIAL
 197 #define CONFIG_SYS_NS16550_REG_SIZE     1
 198
 199 #define CONFIG_SYS_BAUDRATE_TABLE       \
 200         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 201
 202 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 203 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 204
 205 /* I2C */
 206 #define CONFIG_SYS_I2C
 207 #define CONFIG_SYS_I2C_FSL
 208 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 209 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 210 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 211 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 212 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 213 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 214 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 215
 216 /*
 217  * General PCI
 218  * Addresses are mapped 1-1.
 219  */
 220 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 221 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 222 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
 223 #define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 224 #define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 225 #define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000      /* 256M */
 226 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000
 227 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
 228 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000      /* 1M */
 229
 230 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057   /* Motorola */
 231
 232 /*
 233  * TSEC
 234  */
 235
 236 #define CONFIG_GMII                     /* MII PHY management */
 237
 238 #ifdef CONFIG_TSEC1
 239 #define CONFIG_HAS_ETH0
 240 #define CONFIG_TSEC1_NAME       "TSEC0"
 241 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 242 #define TSEC1_PHY_ADDR          0x1c
 243 #define TSEC1_FLAGS             TSEC_GIGABIT
 244 #define TSEC1_PHYIDX            0
 245 #endif
 246
 247 #ifdef CONFIG_TSEC2
 248 #define CONFIG_HAS_ETH1
 249 #define CONFIG_TSEC2_NAME       "TSEC1"
 250 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 251 #define TSEC2_PHY_ADDR          4
 252 #define TSEC2_FLAGS             TSEC_GIGABIT
 253 #define TSEC2_PHYIDX            0
 254 #endif
 255
 256 /* Options are: TSEC[0-1] */
 257 #define CONFIG_ETHPRIME                 "TSEC1"
 258
 259 /*
 260  * Configure on-board RTC
 261  */
 262 #define CONFIG_RTC_DS1337
 263 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 264
 265 /*
 266  * Environment
 267  */
 268 #if !defined(CONFIG_SYS_RAMBOOT)
 269         #define CONFIG_ENV_ADDR         \
 270                         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 271         #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
 272         #define CONFIG_ENV_SIZE         0x2000
 273
 274 /* Address and size of Redundant Environment Sector */
 275 #else
 276         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 277         #define CONFIG_ENV_SIZE         0x2000
 278 #endif
 279
 280 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 281 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 282
 283 /*
 284  * BOOTP options
 285  */
 286 #define CONFIG_BOOTP_BOOTFILESIZE
 287
 288 /*
 289  * Command line configuration.
 290  */
 291
 292 /*
 293  * Miscellaneous configurable options
 294  */
 295 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 296 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 297
 298                                 /* Boot Argument Buffer Size */
 299 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 300
 301 /*
 302  * For booting Linux, the board info and command line data
 303  * have to be in the first 256 MB of memory, since this is
 304  * the maximum mapped by the Linux kernel during initialization.
 305  */
 306                                 /* Initial Memory map for Linux*/
 307 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)
 308 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 309
 310 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000      /* PCIHOST  */
 311
 312 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
 313
 314 /* System IO Config */
 315 #define CONFIG_SYS_SICRH        (SICRH_TSOBI1 | SICRH_TSOBI2)   /* RGMII */
 316                         /* Enable Internal USB Phy and GPIO on LCD Connector */
 317 #define CONFIG_SYS_SICRL        (SICRL_USBDR_10 | SICRL_LBC)
 318
 319 /*
 320  * Environment Configuration
 321  */
 322 #define CONFIG_ENV_OVERWRITE
 323
 324 #define CONFIG_NETDEV           "eth1"
 325
 326 #define CONFIG_HOSTNAME         "mpc8313erdb"
 327 #define CONFIG_ROOTPATH         "/nfs/root/path"
 328 #define CONFIG_BOOTFILE         "uImage"
 329                                 /* U-Boot image on TFTP server */
 330 #define CONFIG_UBOOTPATH        "u-boot.bin"
 331 #define CONFIG_FDTFILE          "mpc8313erdb.dtb"
 332
 333                                 /* default location for tftp and bootm */
 334 #define CONFIG_LOADADDR         800000
 335
 336 #define CONFIG_EXTRA_ENV_SETTINGS \
 337         "netdev=" CONFIG_NETDEV "\0"                                    \
 338         "ethprime=TSEC1\0"                                              \
 339         "uboot=" CONFIG_UBOOTPATH "\0"                                  \
 340         "tftpflash=tftpboot $loadaddr $uboot; "                         \
 341                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 342                         " +$filesize; " \
 343                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 344                         " +$filesize; " \
 345                 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
 346                         " $filesize; "  \
 347                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 348                         " +$filesize; " \
 349                 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
 350                         " $filesize\0"  \
 351         "fdtaddr=780000\0"                                              \
 352         "fdtfile=" CONFIG_FDTFILE "\0"                                  \
 353         "console=ttyS0\0"                                               \
 354         "setbootargs=setenv bootargs "                                  \
 355                 "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
 356         "setipargs=setenv bootargs nfsroot=$serverip:$rootpath "         \
 357                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"\
 358                                                         "$netdev:off " \
 359                 "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
 360
 361 #define CONFIG_NFSBOOTCOMMAND                                           \
 362         "setenv rootdev /dev/nfs;"                                      \
 363         "run setbootargs;"                                              \
 364         "run setipargs;"                                                \
 365         "tftp $loadaddr $bootfile;"                                     \
 366         "tftp $fdtaddr $fdtfile;"                                       \
 367         "bootm $loadaddr - $fdtaddr"
 368
 369 #define CONFIG_RAMBOOTCOMMAND                                           \
 370         "setenv rootdev /dev/ram;"                                      \
 371         "run setbootargs;"                                              \
 372         "tftp $ramdiskaddr $ramdiskfile;"                               \
 373         "tftp $loadaddr $bootfile;"                                     \
 374         "tftp $fdtaddr $fdtfile;"                                       \
 375         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 376
 377 #endif  /* __CONFIG_H */