2 * Copyright (C) Freescale Semiconductor, Inc. 2006, 2010.
4 * SPDX-License-Identifier: GPL-2.0+
7 * mpc8313epb board configuration file
14 * High Level Configuration Options
17 #define CONFIG_MPC831x 1
18 #define CONFIG_MPC8313 1
19 #define CONFIG_MPC8313ERDB 1
22 #define CONFIG_SPL_INIT_MINIMAL
23 #define CONFIG_SPL_FLUSH_IMAGE
24 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
25 #define CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
27 #ifdef CONFIG_SPL_BUILD
28 #define CONFIG_NS16550_MIN_FUNCTIONS
31 #define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
32 #define CONFIG_SPL_MAX_SIZE (4 * 1024)
33 #define CONFIG_SPL_PAD_TO 0x4000
35 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
36 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
37 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
38 #define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
39 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
40 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)
42 #ifdef CONFIG_SPL_BUILD
43 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
46 #endif /* CONFIG_NAND */
48 #ifndef CONFIG_SYS_MONITOR_BASE
49 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
52 #define CONFIG_PCI_INDIRECT_BRIDGE
53 #define CONFIG_FSL_ELBC 1
55 #define CONFIG_MISC_INIT_R
63 #define CONFIG_VSC7385_ENET
66 #ifdef CONFIG_SYS_66MHZ
67 #define CONFIG_83XX_CLKIN 66666667 /* in Hz */
68 #elif defined(CONFIG_SYS_33MHZ)
69 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */
71 #error Unknown oscillator frequency.
74 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
76 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r */
78 #define CONFIG_SYS_IMMR 0xE0000000
80 #if defined(CONFIG_NAND) && !defined(CONFIG_SPL_BUILD)
81 #define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR
84 #define CONFIG_SYS_MEMTEST_START 0x00001000
85 #define CONFIG_SYS_MEMTEST_END 0x07f00000
87 /* Early revs of this board will lock up hard when attempting
88 * to access the PMC registers, unless a JTAG debugger is
89 * connected, or some resistor modifications are made.
91 #define CONFIG_SYS_8313ERDB_BROKEN_PMC 1
93 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
94 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
97 * Device configurations
102 #ifdef CONFIG_VSC7385_ENET
106 /* The flash address and size of the VSC7385 firmware image */
107 #define CONFIG_VSC7385_IMAGE 0xFE7FE000
108 #define CONFIG_VSC7385_IMAGE_SIZE 8192
115 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
116 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
117 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
120 * Manually set up DDR parameters, as this board does not
121 * seem to have the SPD connected to I2C.
123 #define CONFIG_SYS_DDR_SIZE 128 /* MB */
124 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
125 | CSCONFIG_ODT_RD_NEVER \
126 | CSCONFIG_ODT_WR_ONLY_CURRENT \
127 | CSCONFIG_ROW_BIT_13 \
128 | CSCONFIG_COL_BIT_10)
131 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
132 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
133 | (0 << TIMING_CFG0_WRT_SHIFT) \
134 | (0 << TIMING_CFG0_RRT_SHIFT) \
135 | (0 << TIMING_CFG0_WWT_SHIFT) \
136 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
137 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
138 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
139 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
141 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
142 | (8 << TIMING_CFG1_ACTTOPRE_SHIFT) \
143 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
144 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
145 | (10 << TIMING_CFG1_REFREC_SHIFT) \
146 | (3 << TIMING_CFG1_WRREC_SHIFT) \
147 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
148 | (2 << TIMING_CFG1_WRTORD_SHIFT))
150 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
151 | (5 << TIMING_CFG2_CPO_SHIFT) \
152 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
153 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
154 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
155 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
156 | (6 << TIMING_CFG2_FOUR_ACT_SHIFT))
157 /* 0x129048c6 */ /* P9-45,may need tuning */
158 #define CONFIG_SYS_DDR_INTERVAL ((1296 << SDRAM_INTERVAL_REFINT_SHIFT) \
159 | (1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
161 #if defined(CONFIG_DDR_2T_TIMING)
162 #define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \
163 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
168 #define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \
169 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
173 #define CONFIG_SYS_SDRAM_CFG2 0x00401000
174 /* set burst length to 8 for 32-bit data path */
175 #define CONFIG_SYS_DDR_MODE ((0x4448 << SDRAM_MODE_ESD_SHIFT) \
176 | (0x0632 << SDRAM_MODE_SD_SHIFT))
178 #define CONFIG_SYS_DDR_MODE_2 0x8000C000
180 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
182 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
188 * FLASH on the Local Bus
190 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
191 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
192 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
193 #define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */
194 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
195 #define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */
196 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
198 #define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \
199 | BR_PS_16 /* 16 bit port */ \
200 | BR_MS_GPCM /* MSEL = GPCM */ \
202 #define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
207 /* 0xFF006FF7 TODO SLOW 16 MB flash size */
208 /* window base at flash base */
209 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
210 /* 16 MB window size */
211 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_16MB)
213 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
214 #define CONFIG_SYS_MAX_FLASH_SECT 135 /* sectors per device */
216 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
217 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
219 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && \
220 !defined(CONFIG_SPL_BUILD)
221 #define CONFIG_SYS_RAMBOOT
224 #define CONFIG_SYS_INIT_RAM_LOCK 1
225 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */
226 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
228 #define CONFIG_SYS_GBL_DATA_OFFSET \
229 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
230 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
232 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
233 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
234 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
237 * Local Bus LCRR and LBCR regs
239 #define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
240 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
241 #define CONFIG_SYS_LBC_LBCR (0x00040000 /* TODO */ \
242 | (0xFF << LBCR_BMT_SHIFT) \
243 | 0xF) /* 0x0004ff0f */
245 /* LB refresh timer prescal, 266MHz/32 */
246 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /*TODO */
248 /* drivers/mtd/nand/nand.c */
249 #if defined(CONFIG_NAND) && defined(CONFIG_SPL_BUILD)
250 #define CONFIG_SYS_NAND_BASE 0xFFF00000
252 #define CONFIG_SYS_NAND_BASE 0xE2800000
255 #define CONFIG_MTD_DEVICE
256 #define CONFIG_MTD_PARTITION
258 #define CONFIG_SYS_MAX_NAND_DEVICE 1
259 #define CONFIG_NAND_FSL_ELBC 1
260 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384
261 #define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024)
263 #define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \
264 | BR_DECC_CHK_GEN /* Use HW ECC */ \
265 | BR_PS_8 /* 8 bit port */ \
266 | BR_MS_FCM /* MSEL = FCM */ \
268 #define CONFIG_SYS_NAND_OR_PRELIM \
269 (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
279 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
280 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM
281 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NOR_BR_PRELIM
282 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NOR_OR_PRELIM
284 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
285 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
286 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
287 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
290 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
291 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
293 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
294 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
296 /* local bus write LED / read status buffer (BCSR) mapping */
297 #define CONFIG_SYS_BCSR_ADDR 0xFA000000
298 #define CONFIG_SYS_BCSR_SIZE (32 * 1024) /* 0x00008000 */
299 /* map at 0xFA000000 on LCS3 */
300 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_BCSR_ADDR \
301 | BR_PS_8 /* 8 bit port */ \
302 | BR_MS_GPCM /* MSEL = GPCM */ \
305 #define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_BCSR_SIZE) \
314 #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_BCSR_ADDR
315 #define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
319 #ifdef CONFIG_VSC7385_ENET
321 /* VSC7385 Base address on LCS2 */
322 #define CONFIG_SYS_VSC7385_BASE 0xF0000000
323 #define CONFIG_SYS_VSC7385_SIZE (128 * 1024) /* 0x00020000 */
325 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VSC7385_BASE \
326 | BR_PS_8 /* 8 bit port */ \
327 | BR_MS_GPCM /* MSEL = GPCM */ \
329 #define CONFIG_SYS_OR2_PRELIM (P2SZ_TO_AM(CONFIG_SYS_VSC7385_SIZE) \
339 /* Access window base at VSC7385 base */
340 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE
341 #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_128KB)
345 #define CONFIG_MPC83XX_GPIO 1
350 #define CONFIG_CONS_INDEX 1
351 #define CONFIG_SYS_NS16550_SERIAL
352 #define CONFIG_SYS_NS16550_REG_SIZE 1
354 #define CONFIG_SYS_BAUDRATE_TABLE \
355 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
357 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
358 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
361 #define CONFIG_SYS_I2C
362 #define CONFIG_SYS_I2C_FSL
363 #define CONFIG_SYS_FSL_I2C_SPEED 400000
364 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
365 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
366 #define CONFIG_SYS_FSL_I2C2_SPEED 400000
367 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
368 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
369 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
373 * Addresses are mapped 1-1.
375 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
376 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
377 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
378 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
379 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
380 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
381 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000
382 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
383 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
385 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
390 #define CONFIG_TSEC_ENET /* TSEC ethernet support */
392 #define CONFIG_GMII /* MII PHY management */
395 #define CONFIG_HAS_ETH0
396 #define CONFIG_TSEC1_NAME "TSEC0"
397 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
398 #define TSEC1_PHY_ADDR 0x1c
399 #define TSEC1_FLAGS TSEC_GIGABIT
400 #define TSEC1_PHYIDX 0
404 #define CONFIG_HAS_ETH1
405 #define CONFIG_TSEC2_NAME "TSEC1"
406 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
407 #define TSEC2_PHY_ADDR 4
408 #define TSEC2_FLAGS TSEC_GIGABIT
409 #define TSEC2_PHYIDX 0
412 /* Options are: TSEC[0-1] */
413 #define CONFIG_ETHPRIME "TSEC1"
416 * Configure on-board RTC
418 #define CONFIG_RTC_DS1337
419 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
424 #if defined(CONFIG_NAND)
425 #define CONFIG_ENV_OFFSET (512 * 1024)
426 #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
427 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
428 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
429 #define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4)
430 #define CONFIG_ENV_OFFSET_REDUND \
431 (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
432 #elif !defined(CONFIG_SYS_RAMBOOT)
433 #define CONFIG_ENV_ADDR \
434 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
435 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
436 #define CONFIG_ENV_SIZE 0x2000
438 /* Address and size of Redundant Environment Sector */
440 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
441 #define CONFIG_ENV_SIZE 0x2000
444 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
445 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
450 #define CONFIG_BOOTP_BOOTFILESIZE
453 * Command line configuration.
457 * Miscellaneous configurable options
459 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
460 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
462 /* Boot Argument Buffer Size */
463 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
466 * For booting Linux, the board info and command line data
467 * have to be in the first 256 MB of memory, since this is
468 * the maximum mapped by the Linux kernel during initialization.
470 /* Initial Memory map for Linux*/
471 #define CONFIG_SYS_BOOTMAPSZ (256 << 20)
472 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
474 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
476 #ifdef CONFIG_SYS_66MHZ
478 /* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */
480 #define CONFIG_SYS_HRCW_LOW (\
481 0x20000000 /* reserved, must be set */ |\
483 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
484 HRCWL_DDR_TO_SCB_CLK_2X1 |\
485 HRCWL_CSB_TO_CLKIN_2X1 |\
486 HRCWL_CORE_TO_CSB_2X1)
488 #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
490 #elif defined(CONFIG_SYS_33MHZ)
492 /* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */
494 #define CONFIG_SYS_HRCW_LOW (\
495 0x20000000 /* reserved, must be set */ |\
497 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
498 HRCWL_DDR_TO_SCB_CLK_2X1 |\
499 HRCWL_CSB_TO_CLKIN_5X1 |\
500 HRCWL_CORE_TO_CSB_2X1)
502 #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 5)
506 #define CONFIG_SYS_HRCW_HIGH_BASE (\
508 HRCWH_PCI1_ARBITER_ENABLE |\
510 HRCWH_BOOTSEQ_DISABLE |\
511 HRCWH_SW_WATCHDOG_DISABLE |\
512 HRCWH_TSEC1M_IN_RGMII |\
513 HRCWH_TSEC2M_IN_RGMII |\
517 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
518 HRCWH_FROM_0XFFF00100 |\
519 HRCWH_ROM_LOC_NAND_SP_8BIT |\
522 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
523 HRCWH_FROM_0X00000100 |\
524 HRCWH_ROM_LOC_LOCAL_16BIT |\
528 /* System IO Config */
529 #define CONFIG_SYS_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */
530 /* Enable Internal USB Phy and GPIO on LCD Connector */
531 #define CONFIG_SYS_SICRL (SICRL_USBDR_10 | SICRL_LBC)
533 #define CONFIG_SYS_HID0_INIT 0x000000000
534 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
535 HID0_ENABLE_INSTRUCTION_CACHE | \
536 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
538 #define CONFIG_SYS_HID2 HID2_HBE
540 #define CONFIG_HIGH_BATS 1 /* High BATs supported */
542 /* DDR @ 0x00000000 */
543 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW)
544 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
549 /* PCI @ 0x80000000 */
550 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW)
551 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
555 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
557 | BATL_CACHEINHIBIT \
558 | BATL_GUARDEDSTORAGE)
559 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
564 /* PCI2 not supported on 8313 */
565 #define CONFIG_SYS_IBAT3L (0)
566 #define CONFIG_SYS_IBAT3U (0)
567 #define CONFIG_SYS_IBAT4L (0)
568 #define CONFIG_SYS_IBAT4U (0)
570 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
571 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
573 | BATL_CACHEINHIBIT \
574 | BATL_GUARDEDSTORAGE)
575 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
580 /* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
581 #define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE)
582 #define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
584 #define CONFIG_SYS_IBAT7L (0)
585 #define CONFIG_SYS_IBAT7U (0)
587 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
588 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
589 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
590 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
591 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
592 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
593 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
594 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
595 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
596 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
597 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
598 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
599 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
600 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
601 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
602 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
605 * Environment Configuration
607 #define CONFIG_ENV_OVERWRITE
609 #define CONFIG_NETDEV "eth1"
611 #define CONFIG_HOSTNAME mpc8313erdb
612 #define CONFIG_ROOTPATH "/nfs/root/path"
613 #define CONFIG_BOOTFILE "uImage"
614 /* U-Boot image on TFTP server */
615 #define CONFIG_UBOOTPATH "u-boot.bin"
616 #define CONFIG_FDTFILE "mpc8313erdb.dtb"
618 /* default location for tftp and bootm */
619 #define CONFIG_LOADADDR 800000
621 #define CONFIG_EXTRA_ENV_SETTINGS \
622 "netdev=" CONFIG_NETDEV "\0" \
624 "uboot=" CONFIG_UBOOTPATH "\0" \
625 "tftpflash=tftpboot $loadaddr $uboot; " \
626 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
628 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
630 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
632 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
634 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
637 "fdtfile=" CONFIG_FDTFILE "\0" \
639 "setbootargs=setenv bootargs " \
640 "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
641 "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
642 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"\
644 "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
646 #define CONFIG_NFSBOOTCOMMAND \
647 "setenv rootdev /dev/nfs;" \
650 "tftp $loadaddr $bootfile;" \
651 "tftp $fdtaddr $fdtfile;" \
652 "bootm $loadaddr - $fdtaddr"
654 #define CONFIG_RAMBOOTCOMMAND \
655 "setenv rootdev /dev/ram;" \
657 "tftp $ramdiskaddr $ramdiskfile;" \
658 "tftp $loadaddr $bootfile;" \
659 "tftp $fdtaddr $fdtfile;" \
660 "bootm $loadaddr $ramdiskaddr $fdtaddr"
662 #endif /* __CONFIG_H */