include/configs/MPC8308RDB.h

   1 /*
   2  * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
   3  * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
   4  *
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15 #define CONFIG_E300             1 /* E300 family */
  16 #define CONFIG_MPC830x          1 /* MPC830x family */
  17 #define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
  18
  19 #define CONFIG_MISC_INIT_R
  20
  21 #ifdef CONFIG_MMC
  22 #define CONFIG_FSL_ESDHC
  23 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
  24 #define CONFIG_SYS_FSL_ESDHC_USE_PIO
  25 #endif
  26
  27 /*
  28  * On-board devices
  29  *
  30  * TSEC1 is SoC TSEC
  31  * TSEC2 is VSC switch
  32  */
  33 #define CONFIG_TSEC1
  34 #define CONFIG_VSC7385_ENET
  35
  36 /*
  37  * System Clock Setup
  38  */
  39 #define CONFIG_83XX_CLKIN       33333333 /* in Hz */
  40 #define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN
  41
  42 /*
  43  * Hardware Reset Configuration Word
  44  * if CLKIN is 66.66MHz, then
  45  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
  46  * We choose the A type silicon as default, so the core is 400Mhz.
  47  */
  48 #define CONFIG_SYS_HRCW_LOW (\
  49         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  50         HRCWL_DDR_TO_SCB_CLK_2X1 |\
  51         HRCWL_SVCOD_DIV_2 |\
  52         HRCWL_CSB_TO_CLKIN_4X1 |\
  53         HRCWL_CORE_TO_CSB_3X1)
  54 /*
  55  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
  56  * in 8308's HRCWH according to the manual, but original Freescale's
  57  * code has them and I've expirienced some problems using the board
  58  * with BDI3000 attached when I've tried to set these bits to zero
  59  * (UART doesn't work after the 'reset run' command).
  60  */
  61 #define CONFIG_SYS_HRCW_HIGH (\
  62         HRCWH_PCI_HOST |\
  63         HRCWH_PCI1_ARBITER_ENABLE |\
  64         HRCWH_CORE_ENABLE |\
  65         HRCWH_FROM_0X00000100 |\
  66         HRCWH_BOOTSEQ_DISABLE |\
  67         HRCWH_SW_WATCHDOG_DISABLE |\
  68         HRCWH_ROM_LOC_LOCAL_16BIT |\
  69         HRCWH_RL_EXT_LEGACY |\
  70         HRCWH_TSEC1M_IN_RGMII |\
  71         HRCWH_TSEC2M_IN_RGMII |\
  72         HRCWH_BIG_ENDIAN)
  73
  74 /*
  75  * System IO Config
  76  */
  77 #define CONFIG_SYS_SICRH (\
  78         SICRH_ESDHC_A_SD |\
  79         SICRH_ESDHC_B_SD |\
  80         SICRH_ESDHC_C_SD |\
  81         SICRH_GPIO_A_TSEC2 |\
  82         SICRH_GPIO_B_TSEC2_GTX_CLK125 |\
  83         SICRH_IEEE1588_A_GPIO |\
  84         SICRH_USB |\
  85         SICRH_GTM_GPIO |\
  86         SICRH_IEEE1588_B_GPIO |\
  87         SICRH_ETSEC2_CRS |\
  88         SICRH_GPIOSEL_1 |\
  89         SICRH_TMROBI_V3P3 |\
  90         SICRH_TSOBI1_V2P5 |\
  91         SICRH_TSOBI2_V2P5)      /* 0x01b7d103 */
  92 #define CONFIG_SYS_SICRL (\
  93         SICRL_SPI_PF0 |\
  94         SICRL_UART_PF0 |\
  95         SICRL_IRQ_PF0 |\
  96         SICRL_I2C2_PF0 |\
  97         SICRL_ETSEC1_GTX_CLK125)        /* 0x00000040 */
  98
  99 /*
 100  * IMMR new address
 101  */
 102 #define CONFIG_SYS_IMMR         0xE0000000
 103
 104 /*
 105  * SERDES
 106  */
 107 #define CONFIG_FSL_SERDES
 108 #define CONFIG_FSL_SERDES1      0xe3000
 109
 110 /*
 111  * Arbiter Setup
 112  */
 113 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
 114 #define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
 115 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */
 116
 117 /*
 118  * DDR Setup
 119  */
 120 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
 121 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
 122 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
 123 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 124 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 125                                 | DDRCDR_PZ_LOZ \
 126                                 | DDRCDR_NZ_LOZ \
 127                                 | DDRCDR_ODT \
 128                                 | DDRCDR_Q_DRN)
 129                                 /* 0x7b880001 */
 130 /*
 131  * Manually set up DDR parameters
 132  * consist of two chips HY5PS12621BFP-C4 from HYNIX
 133  */
 134
 135 #define CONFIG_SYS_DDR_SIZE             128 /* MB */
 136
 137 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
 138 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
 139                                 | CSCONFIG_ODT_RD_NEVER \
 140                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
 141                                 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
 142                                 /* 0x80010102 */
 143 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 144 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
 145                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
 146                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
 147                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
 148                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 149                                 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 150                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 151                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 152                                 /* 0x00220802 */
 153 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
 154                                 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 155                                 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
 156                                 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
 157                                 | (6 << TIMING_CFG1_REFREC_SHIFT) \
 158                                 | (2 << TIMING_CFG1_WRREC_SHIFT) \
 159                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 160                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 161                                 /* 0x27256222 */
 162 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
 163                                 | (4 << TIMING_CFG2_CPO_SHIFT) \
 164                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 165                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 166                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 167                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 168                                 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
 169                                 /* 0x121048c5 */
 170 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
 171                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 172                                 /* 0x03600100 */
 173 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 174                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 175                                 | SDRAM_CFG_DBW_32)
 176                                 /* 0x43080000 */
 177
 178 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
 179 #define CONFIG_SYS_DDR_MODE             ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
 180                                 | (0x0232 << SDRAM_MODE_SD_SHIFT))
 181                                 /* ODT 150ohm CL=3, AL=1 on SDRAM */
 182 #define CONFIG_SYS_DDR_MODE2            0x00000000
 183
 184 /*
 185  * Memory test
 186  */
 187 #define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
 188 #define CONFIG_SYS_MEMTEST_END          0x07f00000
 189
 190 /*
 191  * The reserved memory
 192  */
 193 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 194
 195 #define CONFIG_SYS_MONITOR_LEN  (512 * 1024) /* Reserve 512 kB for Mon */
 196 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 197
 198 /*
 199  * Initial RAM Base Address Setup
 200  */
 201 #define CONFIG_SYS_INIT_RAM_LOCK        1
 202 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 203 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 204 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 205         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 206
 207 /*
 208  * Local Bus Configuration & Clock Setup
 209  */
 210 #define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
 211 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
 212 #define CONFIG_SYS_LBC_LBCR             0x00040000
 213
 214 /*
 215  * FLASH on the Local Bus
 216  */
 217 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 218 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 219 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 220
 221 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 222 #define CONFIG_SYS_FLASH_SIZE           8 /* FLASH size is 8M */
 223 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */
 224
 225 /* Window base at flash base */
 226 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 227 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 228
 229 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 230                                 | BR_PS_16      /* 16 bit port */ \
 231                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 232                                 | BR_V)         /* valid */
 233 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 234                                 | OR_UPM_XAM \
 235                                 | OR_GPCM_CSNT \
 236                                 | OR_GPCM_ACS_DIV2 \
 237                                 | OR_GPCM_XACS \
 238                                 | OR_GPCM_SCY_15 \
 239                                 | OR_GPCM_TRLX_SET \
 240                                 | OR_GPCM_EHTR_SET)
 241
 242 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 243 /* 127 64KB sectors and 8 8KB top sectors per device */
 244 #define CONFIG_SYS_MAX_FLASH_SECT       135
 245
 246 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 247 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 248
 249 /*
 250  * NAND Flash on the Local Bus
 251  */
 252 #define CONFIG_SYS_NAND_BASE    0xE0600000              /* 0xE0600000 */
 253 #define CONFIG_SYS_NAND_WINDOW_SIZE     (32 * 1024)     /* 0x00008000 */
 254 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_NAND_BASE \
 255                                 | BR_DECC_CHK_GEN       /* Use HW ECC */ \
 256                                 | BR_PS_8               /* 8 bit Port */ \
 257                                 | BR_MS_FCM             /* MSEL = FCM */ \
 258                                 | BR_V)                 /* valid */
 259 #define CONFIG_SYS_OR1_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
 260                                 | OR_FCM_CSCT \
 261                                 | OR_FCM_CST \
 262                                 | OR_FCM_CHT \
 263                                 | OR_FCM_SCY_1 \
 264                                 | OR_FCM_TRLX \
 265                                 | OR_FCM_EHTR)
 266                                 /* 0xFFFF8396 */
 267
 268 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_NAND_BASE
 269 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_32KB)
 270
 271 #ifdef CONFIG_VSC7385_ENET
 272 #define CONFIG_TSEC2
 273                                         /* VSC7385 Base address on CS2 */
 274 #define CONFIG_SYS_VSC7385_BASE         0xF0000000
 275 #define CONFIG_SYS_VSC7385_SIZE         (128 * 1024) /* 0x00020000 */
 276 #define CONFIG_SYS_BR2_PRELIM           (CONFIG_SYS_VSC7385_BASE \
 277                                         | BR_PS_8       /* 8-bit port */ \
 278                                         | BR_MS_GPCM    /* MSEL = GPCM */ \
 279                                         | BR_V)         /* valid */
 280                                         /* 0xF0000801 */
 281 #define CONFIG_SYS_OR2_PRELIM           (P2SZ_TO_AM(CONFIG_SYS_VSC7385_SIZE) \
 282                                         | OR_GPCM_CSNT \
 283                                         | OR_GPCM_XACS \
 284                                         | OR_GPCM_SCY_15 \
 285                                         | OR_GPCM_SETA \
 286                                         | OR_GPCM_TRLX_SET \
 287                                         | OR_GPCM_EHTR_SET)
 288                                         /* 0xFFFE09FF */
 289 /* Access window base at VSC7385 base */
 290 #define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_VSC7385_BASE
 291 /* Access window size 128K */
 292 #define CONFIG_SYS_LBLAWAR2_PRELIM      (LBLAWAR_EN | LBLAWAR_128KB)
 293 /* The flash address and size of the VSC7385 firmware image */
 294 #define CONFIG_VSC7385_IMAGE            0xFE7FE000
 295 #define CONFIG_VSC7385_IMAGE_SIZE       8192
 296 #endif
 297 /*
 298  * Serial Port
 299  */
 300 #define CONFIG_SYS_NS16550_SERIAL
 301 #define CONFIG_SYS_NS16550_REG_SIZE     1
 302 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 303
 304 #define CONFIG_SYS_BAUDRATE_TABLE  \
 305         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 306
 307 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
 308 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
 309
 310 /* I2C */
 311 #define CONFIG_SYS_I2C
 312 #define CONFIG_SYS_I2C_FSL
 313 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 314 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 315 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 316 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 317 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 318 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 319 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }
 320
 321 /*
 322  * SPI on header J8
 323  *
 324  * WARNING: enabling this will break TSEC2 (connected to the Vitesse switch)
 325  * due to a pinmux conflict between GPIO9 (SPI chip select )and the TSEC2 pins.
 326  */
 327 #ifdef CONFIG_MPC8XXX_SPI
 328 #define CONFIG_USE_SPIFLASH
 329 #endif
 330
 331 /*
 332  * Board info - revision and where boot from
 333  */
 334 #define CONFIG_SYS_I2C_PCF8574A_ADDR    0x39
 335
 336 /*
 337  * Config on-board RTC
 338  */
 339 #define CONFIG_RTC_DS1337       /* ds1339 on board, use ds1337 rtc via i2c */
 340 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
 341
 342 /*
 343  * General PCI
 344  * Addresses are mapped 1-1.
 345  */
 346 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 347 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
 348 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
 349 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 350 #define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
 351 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
 352 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 353 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
 354 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 355
 356 /* enable PCIE clock */
 357 #define CONFIG_SYS_SCCR_PCIEXP1CM       1
 358
 359 #define CONFIG_PCI_INDIRECT_BRIDGE
 360 #define CONFIG_PCIE
 361
 362 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 363 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
 364
 365 /*
 366  * TSEC
 367  */
 368 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 369 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 370 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 371 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 372
 373 /*
 374  * TSEC ethernet configuration
 375  */
 376 #define CONFIG_MII              1 /* MII PHY management */
 377 #define CONFIG_TSEC1_NAME       "eTSEC0"
 378 #define CONFIG_TSEC2_NAME       "eTSEC1"
 379 #define TSEC1_PHY_ADDR          2
 380 #define TSEC2_PHY_ADDR          1
 381 #define TSEC1_PHYIDX            0
 382 #define TSEC2_PHYIDX            0
 383 #define TSEC1_FLAGS             TSEC_GIGABIT
 384 #define TSEC2_FLAGS             TSEC_GIGABIT
 385
 386 /* Options are: eTSEC[0-1] */
 387 #define CONFIG_ETHPRIME         "eTSEC0"
 388
 389 /*
 390  * Environment
 391  */
 392 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 393                                  CONFIG_SYS_MONITOR_LEN)
 394 #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
 395 #define CONFIG_ENV_SIZE         0x2000
 396 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 397 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 398
 399 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 400 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 401
 402 /*
 403  * BOOTP options
 404  */
 405 #define CONFIG_BOOTP_BOOTFILESIZE
 406
 407 /*
 408  * Command line configuration.
 409  */
 410
 411 /*
 412  * Miscellaneous configurable options
 413  */
 414 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 415
 416 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 417
 418 /* Boot Argument Buffer Size */
 419 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 420
 421 /*
 422  * For booting Linux, the board info and command line data
 423  * have to be in the first 256 MB of memory, since this is
 424  * the maximum mapped by the Linux kernel during initialization.
 425  */
 426 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 427 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 428
 429 /*
 430  * Core HID Setup
 431  */
 432 #define CONFIG_SYS_HID0_INIT    0x000000000
 433 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 434                                  HID0_ENABLE_INSTRUCTION_CACHE | \
 435                                  HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
 436 #define CONFIG_SYS_HID2         HID2_HBE
 437
 438 /*
 439  * MMU Setup
 440  */
 441
 442 /* DDR: cache cacheable */
 443 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
 444                                         BATL_MEMCOHERENCE)
 445 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
 446                                         BATU_VS | BATU_VP)
 447 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 448 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 449
 450 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
 451 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
 452                         BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 453 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
 454                                         BATU_VP)
 455 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 456 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 457
 458 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 459 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 460                                         BATL_MEMCOHERENCE)
 461 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
 462                                         BATU_VS | BATU_VP)
 463 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 464                                         BATL_CACHEINHIBIT | \
 465                                         BATL_GUARDEDSTORAGE)
 466 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 467
 468 /* Stack in dcache: cacheable, no memory coherence */
 469 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 470 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
 471                                         BATU_VS | BATU_VP)
 472 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 473 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 474
 475 /*
 476  * Environment Configuration
 477  */
 478
 479 #define CONFIG_ENV_OVERWRITE
 480
 481 #if defined(CONFIG_TSEC_ENET)
 482 #define CONFIG_HAS_ETH0
 483 #define CONFIG_HAS_ETH1
 484 #endif
 485
 486 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 487
 488
 489 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 490         "netdev=eth0\0"                                                 \
 491         "consoledev=ttyS0\0"                                            \
 492         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 493                 "nfsroot=${serverip}:${rootpath}\0"                     \
 494         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 495         "addip=setenv bootargs ${bootargs} "                            \
 496                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 497                 ":${hostname}:${netdev}:off panic=1\0"                  \
 498         "addtty=setenv bootargs ${bootargs}"                            \
 499                 " console=${consoledev},${baudrate}\0"                  \
 500         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 501         "addmisc=setenv bootargs ${bootargs}\0"                         \
 502         "kernel_addr=FE080000\0"                                        \
 503         "fdt_addr=FE280000\0"                                           \
 504         "ramdisk_addr=FE290000\0"                                       \
 505         "u-boot=mpc8308rdb/u-boot.bin\0"                                \
 506         "kernel_addr_r=1000000\0"                                       \
 507         "fdt_addr_r=C00000\0"                                           \
 508         "hostname=mpc8308rdb\0"                                         \
 509         "bootfile=mpc8308rdb/uImage\0"                                  \
 510         "fdtfile=mpc8308rdb/mpc8308rdb.dtb\0"                           \
 511         "rootpath=/opt/eldk-4.2/ppc_6xx\0"                              \
 512         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 513                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 514         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 515                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 516         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
 517                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 518                 "run nfsargs addip addtty addmtd addmisc;"              \
 519                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 520         "bootcmd=run flash_self\0"                                      \
 521         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 522         "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)      \
 523                 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
 524                 " +${filesize};cp.b ${fileaddr} "                       \
 525                 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"   \
 526         "upd=run load update\0"                                         \
 527
 528 #endif  /* __CONFIG_H */