include/configs/MPC8308RDB.h

   1 /*
   2  * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
   3  * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
   4  *
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15 #define CONFIG_E300             1 /* E300 family */
  16 #define CONFIG_MPC83xx          1 /* MPC83xx family */
  17 #define CONFIG_MPC830x          1 /* MPC830x family */
  18 #define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
  19 #define CONFIG_MPC8308RDB       1 /* MPC8308RDB board specific */
  20
  21 #define CONFIG_SYS_TEXT_BASE    0xFE000000
  22
  23 #define CONFIG_MISC_INIT_R
  24
  25 /* new uImage format support */
  26 #define CONFIG_FIT                      1
  27 #define CONFIG_FIT_VERBOSE              1
  28
  29 #define CONFIG_MMC     1
  30
  31 #ifdef CONFIG_MMC
  32 #define CONFIG_FSL_ESDHC
  33 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
  34 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
  35 #define CONFIG_SYS_FSL_ESDHC_USE_PIO
  36
  37 #define CONFIG_CMD_MMC
  38 #define CONFIG_GENERIC_MMC
  39 #define CONFIG_CMD_FAT
  40 #define CONFIG_DOS_PARTITION
  41 #endif
  42
  43 /*
  44  * On-board devices
  45  *
  46  * TSEC1 is SoC TSEC
  47  * TSEC2 is VSC switch
  48  */
  49 #define CONFIG_TSEC1
  50 #define CONFIG_VSC7385_ENET
  51
  52 /*
  53  * System Clock Setup
  54  */
  55 #define CONFIG_83XX_CLKIN       33333333 /* in Hz */
  56 #define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN
  57
  58 /*
  59  * Hardware Reset Configuration Word
  60  * if CLKIN is 66.66MHz, then
  61  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
  62  * We choose the A type silicon as default, so the core is 400Mhz.
  63  */
  64 #define CONFIG_SYS_HRCW_LOW (\
  65         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  66         HRCWL_DDR_TO_SCB_CLK_2X1 |\
  67         HRCWL_SVCOD_DIV_2 |\
  68         HRCWL_CSB_TO_CLKIN_4X1 |\
  69         HRCWL_CORE_TO_CSB_3X1)
  70 /*
  71  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
  72  * in 8308's HRCWH according to the manual, but original Freescale's
  73  * code has them and I've expirienced some problems using the board
  74  * with BDI3000 attached when I've tried to set these bits to zero
  75  * (UART doesn't work after the 'reset run' command).
  76  */
  77 #define CONFIG_SYS_HRCW_HIGH (\
  78         HRCWH_PCI_HOST |\
  79         HRCWH_PCI1_ARBITER_ENABLE |\
  80         HRCWH_CORE_ENABLE |\
  81         HRCWH_FROM_0X00000100 |\
  82         HRCWH_BOOTSEQ_DISABLE |\
  83         HRCWH_SW_WATCHDOG_DISABLE |\
  84         HRCWH_ROM_LOC_LOCAL_16BIT |\
  85         HRCWH_RL_EXT_LEGACY |\
  86         HRCWH_TSEC1M_IN_RGMII |\
  87         HRCWH_TSEC2M_IN_RGMII |\
  88         HRCWH_BIG_ENDIAN)
  89
  90 /*
  91  * System IO Config
  92  */
  93 #define CONFIG_SYS_SICRH (\
  94         SICRH_ESDHC_A_SD |\
  95         SICRH_ESDHC_B_SD |\
  96         SICRH_ESDHC_C_SD |\
  97         SICRH_GPIO_A_TSEC2 |\
  98         SICRH_GPIO_B_TSEC2_GTX_CLK125 |\
  99         SICRH_IEEE1588_A_GPIO |\
 100         SICRH_USB |\
 101         SICRH_GTM_GPIO |\
 102         SICRH_IEEE1588_B_GPIO |\
 103         SICRH_ETSEC2_CRS |\
 104         SICRH_GPIOSEL_1 |\
 105         SICRH_TMROBI_V3P3 |\
 106         SICRH_TSOBI1_V2P5 |\
 107         SICRH_TSOBI2_V2P5)      /* 0x01b7d103 */
 108 #define CONFIG_SYS_SICRL (\
 109         SICRL_SPI_PF0 |\
 110         SICRL_UART_PF0 |\
 111         SICRL_IRQ_PF0 |\
 112         SICRL_I2C2_PF0 |\
 113         SICRL_ETSEC1_GTX_CLK125)        /* 0x00000040 */
 114
 115 /*
 116  * IMMR new address
 117  */
 118 #define CONFIG_SYS_IMMR         0xE0000000
 119
 120 /*
 121  * SERDES
 122  */
 123 #define CONFIG_FSL_SERDES
 124 #define CONFIG_FSL_SERDES1      0xe3000
 125
 126 /*
 127  * Arbiter Setup
 128  */
 129 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
 130 #define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
 131 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */
 132
 133 /*
 134  * DDR Setup
 135  */
 136 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
 137 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
 138 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
 139 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 140 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 141                                 | DDRCDR_PZ_LOZ \
 142                                 | DDRCDR_NZ_LOZ \
 143                                 | DDRCDR_ODT \
 144                                 | DDRCDR_Q_DRN)
 145                                 /* 0x7b880001 */
 146 /*
 147  * Manually set up DDR parameters
 148  * consist of two chips HY5PS12621BFP-C4 from HYNIX
 149  */
 150
 151 #define CONFIG_SYS_DDR_SIZE             128 /* MB */
 152
 153 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
 154 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
 155                                 | CSCONFIG_ODT_RD_NEVER \
 156                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
 157                                 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
 158                                 /* 0x80010102 */
 159 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 160 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
 161                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
 162                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
 163                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
 164                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 165                                 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 166                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 167                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 168                                 /* 0x00220802 */
 169 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
 170                                 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 171                                 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
 172                                 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
 173                                 | (6 << TIMING_CFG1_REFREC_SHIFT) \
 174                                 | (2 << TIMING_CFG1_WRREC_SHIFT) \
 175                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 176                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 177                                 /* 0x27256222 */
 178 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
 179                                 | (4 << TIMING_CFG2_CPO_SHIFT) \
 180                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 181                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 182                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 183                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 184                                 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
 185                                 /* 0x121048c5 */
 186 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
 187                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 188                                 /* 0x03600100 */
 189 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 190                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 191                                 | SDRAM_CFG_DBW_32)
 192                                 /* 0x43080000 */
 193
 194 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
 195 #define CONFIG_SYS_DDR_MODE             ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
 196                                 | (0x0232 << SDRAM_MODE_SD_SHIFT))
 197                                 /* ODT 150ohm CL=3, AL=1 on SDRAM */
 198 #define CONFIG_SYS_DDR_MODE2            0x00000000
 199
 200 /*
 201  * Memory test
 202  */
 203 #define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
 204 #define CONFIG_SYS_MEMTEST_END          0x07f00000
 205
 206 /*
 207  * The reserved memory
 208  */
 209 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 210
 211 #define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
 212 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 213
 214 /*
 215  * Initial RAM Base Address Setup
 216  */
 217 #define CONFIG_SYS_INIT_RAM_LOCK        1
 218 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 219 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 220 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 221         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 222
 223 /*
 224  * Local Bus Configuration & Clock Setup
 225  */
 226 #define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
 227 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
 228 #define CONFIG_SYS_LBC_LBCR             0x00040000
 229
 230 /*
 231  * FLASH on the Local Bus
 232  */
 233 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 234 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 235 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 236
 237 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 238 #define CONFIG_SYS_FLASH_SIZE           8 /* FLASH size is 8M */
 239 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */
 240
 241 /* Window base at flash base */
 242 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 243 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 244
 245 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 246                                 | BR_PS_16      /* 16 bit port */ \
 247                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 248                                 | BR_V)         /* valid */
 249 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 250                                 | OR_UPM_XAM \
 251                                 | OR_GPCM_CSNT \
 252                                 | OR_GPCM_ACS_DIV2 \
 253                                 | OR_GPCM_XACS \
 254                                 | OR_GPCM_SCY_15 \
 255                                 | OR_GPCM_TRLX_SET \
 256                                 | OR_GPCM_EHTR_SET)
 257
 258 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 259 /* 127 64KB sectors and 8 8KB top sectors per device */
 260 #define CONFIG_SYS_MAX_FLASH_SECT       135
 261
 262 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 263 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 264
 265 /*
 266  * NAND Flash on the Local Bus
 267  */
 268 #define CONFIG_SYS_NAND_BASE    0xE0600000              /* 0xE0600000 */
 269 #define CONFIG_SYS_NAND_WINDOW_SIZE     (32 * 1024)     /* 0x00008000 */
 270 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_NAND_BASE \
 271                                 | BR_DECC_CHK_GEN       /* Use HW ECC */ \
 272                                 | BR_PS_8               /* 8 bit Port */ \
 273                                 | BR_MS_FCM             /* MSEL = FCM */ \
 274                                 | BR_V)                 /* valid */
 275 #define CONFIG_SYS_OR1_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
 276                                 | OR_FCM_CSCT \
 277                                 | OR_FCM_CST \
 278                                 | OR_FCM_CHT \
 279                                 | OR_FCM_SCY_1 \
 280                                 | OR_FCM_TRLX \
 281                                 | OR_FCM_EHTR)
 282                                 /* 0xFFFF8396 */
 283
 284 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_NAND_BASE
 285 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_32KB)
 286
 287 #ifdef CONFIG_VSC7385_ENET
 288 #define CONFIG_TSEC2
 289                                         /* VSC7385 Base address on CS2 */
 290 #define CONFIG_SYS_VSC7385_BASE         0xF0000000
 291 #define CONFIG_SYS_VSC7385_SIZE         (128 * 1024) /* 0x00020000 */
 292 #define CONFIG_SYS_BR2_PRELIM           (CONFIG_SYS_VSC7385_BASE \
 293                                         | BR_PS_8       /* 8-bit port */ \
 294                                         | BR_MS_GPCM    /* MSEL = GPCM */ \
 295                                         | BR_V)         /* valid */
 296                                         /* 0xF0000801 */
 297 #define CONFIG_SYS_OR2_PRELIM           (P2SZ_TO_AM(CONFIG_SYS_VSC7385_SIZE) \
 298                                         | OR_GPCM_CSNT \
 299                                         | OR_GPCM_XACS \
 300                                         | OR_GPCM_SCY_15 \
 301                                         | OR_GPCM_SETA \
 302                                         | OR_GPCM_TRLX_SET \
 303                                         | OR_GPCM_EHTR_SET)
 304                                         /* 0xFFFE09FF */
 305 /* Access window base at VSC7385 base */
 306 #define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_VSC7385_BASE
 307 /* Access window size 128K */
 308 #define CONFIG_SYS_LBLAWAR2_PRELIM      (LBLAWAR_EN | LBLAWAR_128KB)
 309 /* The flash address and size of the VSC7385 firmware image */
 310 #define CONFIG_VSC7385_IMAGE            0xFE7FE000
 311 #define CONFIG_VSC7385_IMAGE_SIZE       8192
 312 #endif
 313 /*
 314  * Serial Port
 315  */
 316 #define CONFIG_CONS_INDEX       1
 317 #define CONFIG_SYS_NS16550
 318 #define CONFIG_SYS_NS16550_SERIAL
 319 #define CONFIG_SYS_NS16550_REG_SIZE     1
 320 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 321
 322 #define CONFIG_SYS_BAUDRATE_TABLE  \
 323         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 324
 325 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
 326 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
 327
 328 /* Use the HUSH parser */
 329 #define CONFIG_SYS_HUSH_PARSER
 330
 331 /* Pass open firmware flat tree */
 332 #define CONFIG_OF_LIBFDT        1
 333 #define CONFIG_OF_BOARD_SETUP   1
 334 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
 335
 336 /* I2C */
 337 #define CONFIG_SYS_I2C
 338 #define CONFIG_SYS_I2C_FSL
 339 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 340 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 341 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 342 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 343 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 344 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 345 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }
 346
 347 /*
 348  * SPI on header J8
 349  *
 350  * WARNING: enabling this will break TSEC2 (connected to the Vitesse switch)
 351  * due to a pinmux conflict between GPIO9 (SPI chip select )and the TSEC2 pins.
 352  */
 353 #ifdef CONFIG_MPC8XXX_SPI
 354 #define CONFIG_CMD_SPI
 355 #define CONFIG_USE_SPIFLASH
 356 #define CONFIG_SPI_FLASH
 357 #define CONFIG_SPI_FLASH_SPANSION
 358 #define CONFIG_CMD_SF
 359 #endif
 360
 361 /*
 362  * Board info - revision and where boot from
 363  */
 364 #define CONFIG_SYS_I2C_PCF8574A_ADDR    0x39
 365
 366 /*
 367  * Config on-board RTC
 368  */
 369 #define CONFIG_RTC_DS1337       /* ds1339 on board, use ds1337 rtc via i2c */
 370 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
 371
 372 /*
 373  * General PCI
 374  * Addresses are mapped 1-1.
 375  */
 376 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 377 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
 378 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
 379 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 380 #define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
 381 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
 382 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 383 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
 384 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 385
 386 /* enable PCIE clock */
 387 #define CONFIG_SYS_SCCR_PCIEXP1CM       1
 388
 389 #define CONFIG_PCI
 390 #define CONFIG_PCI_INDIRECT_BRIDGE
 391 #define CONFIG_PCIE
 392
 393 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 394
 395 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 396 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
 397
 398 /*
 399  * TSEC
 400  */
 401 #define CONFIG_TSEC_ENET        /* TSEC ethernet support */
 402 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 403 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 404 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 405 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 406
 407 /*
 408  * TSEC ethernet configuration
 409  */
 410 #define CONFIG_MII              1 /* MII PHY management */
 411 #define CONFIG_TSEC1_NAME       "eTSEC0"
 412 #define CONFIG_TSEC2_NAME       "eTSEC1"
 413 #define TSEC1_PHY_ADDR          2
 414 #define TSEC2_PHY_ADDR          1
 415 #define TSEC1_PHYIDX            0
 416 #define TSEC2_PHYIDX            0
 417 #define TSEC1_FLAGS             TSEC_GIGABIT
 418 #define TSEC2_FLAGS             TSEC_GIGABIT
 419
 420 /* Options are: eTSEC[0-1] */
 421 #define CONFIG_ETHPRIME         "eTSEC0"
 422
 423 /*
 424  * Environment
 425  */
 426 #define CONFIG_ENV_IS_IN_FLASH  1
 427 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 428                                  CONFIG_SYS_MONITOR_LEN)
 429 #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
 430 #define CONFIG_ENV_SIZE         0x2000
 431 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 432 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 433
 434 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 435 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 436
 437 /*
 438  * BOOTP options
 439  */
 440 #define CONFIG_BOOTP_BOOTFILESIZE
 441 #define CONFIG_BOOTP_BOOTPATH
 442 #define CONFIG_BOOTP_GATEWAY
 443 #define CONFIG_BOOTP_HOSTNAME
 444
 445 /*
 446  * Command line configuration.
 447  */
 448 #include <config_cmd_default.h>
 449
 450 #define CONFIG_CMD_DATE
 451 #define CONFIG_CMD_DHCP
 452 #define CONFIG_CMD_I2C
 453 #define CONFIG_CMD_MII
 454 #define CONFIG_CMD_NET
 455 #define CONFIG_CMD_PCI
 456 #define CONFIG_CMD_PING
 457
 458 #define CONFIG_CMDLINE_EDITING  1       /* add command line history */
 459
 460 /*
 461  * Miscellaneous configurable options
 462  */
 463 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 464 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 465
 466 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 467
 468 /* Print Buffer Size */
 469 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 470 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 471 /* Boot Argument Buffer Size */
 472 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 473
 474 /*
 475  * For booting Linux, the board info and command line data
 476  * have to be in the first 256 MB of memory, since this is
 477  * the maximum mapped by the Linux kernel during initialization.
 478  */
 479 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 480
 481 /*
 482  * Core HID Setup
 483  */
 484 #define CONFIG_SYS_HID0_INIT    0x000000000
 485 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 486                                  HID0_ENABLE_INSTRUCTION_CACHE | \
 487                                  HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
 488 #define CONFIG_SYS_HID2         HID2_HBE
 489
 490 /*
 491  * MMU Setup
 492  */
 493
 494 /* DDR: cache cacheable */
 495 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
 496                                         BATL_MEMCOHERENCE)
 497 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
 498                                         BATU_VS | BATU_VP)
 499 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 500 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 501
 502 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
 503 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
 504                         BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 505 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
 506                                         BATU_VP)
 507 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 508 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 509
 510 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 511 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 512                                         BATL_MEMCOHERENCE)
 513 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
 514                                         BATU_VS | BATU_VP)
 515 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 516                                         BATL_CACHEINHIBIT | \
 517                                         BATL_GUARDEDSTORAGE)
 518 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 519
 520 /* Stack in dcache: cacheable, no memory coherence */
 521 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 522 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
 523                                         BATU_VS | BATU_VP)
 524 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 525 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 526
 527 /*
 528  * Environment Configuration
 529  */
 530
 531 #define CONFIG_ENV_OVERWRITE
 532
 533 #if defined(CONFIG_TSEC_ENET)
 534 #define CONFIG_HAS_ETH0
 535 #define CONFIG_HAS_ETH1
 536 #endif
 537
 538 #define CONFIG_BAUDRATE 115200
 539
 540 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 541
 542 #define CONFIG_BOOTDELAY        5       /* -1 disables auto-boot */
 543
 544 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 545         "netdev=eth0\0"                                                 \
 546         "consoledev=ttyS0\0"                                            \
 547         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 548                 "nfsroot=${serverip}:${rootpath}\0"                     \
 549         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 550         "addip=setenv bootargs ${bootargs} "                            \
 551                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 552                 ":${hostname}:${netdev}:off panic=1\0"                  \
 553         "addtty=setenv bootargs ${bootargs}"                            \
 554                 " console=${consoledev},${baudrate}\0"                  \
 555         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 556         "addmisc=setenv bootargs ${bootargs}\0"                         \
 557         "kernel_addr=FE080000\0"                                        \
 558         "fdt_addr=FE280000\0"                                           \
 559         "ramdisk_addr=FE290000\0"                                       \
 560         "u-boot=mpc8308rdb/u-boot.bin\0"                                \
 561         "kernel_addr_r=1000000\0"                                       \
 562         "fdt_addr_r=C00000\0"                                           \
 563         "hostname=mpc8308rdb\0"                                         \
 564         "bootfile=mpc8308rdb/uImage\0"                                  \
 565         "fdtfile=mpc8308rdb/mpc8308rdb.dtb\0"                           \
 566         "rootpath=/opt/eldk-4.2/ppc_6xx\0"                              \
 567         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 568                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 569         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 570                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 571         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
 572                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 573                 "run nfsargs addip addtty addmtd addmisc;"              \
 574                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 575         "bootcmd=run flash_self\0"                                      \
 576         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 577         "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)      \
 578                 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
 579                 " +${filesize};cp.b ${fileaddr} "                       \
 580                 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"   \
 581         "upd=run load update\0"                                         \
 582
 583 #endif  /* __CONFIG_H */