2 # Physical Layer USB driver configuration
4 menu "USB Physical Layer drivers"
10 # USB Transceiver Drivers
13 tristate "AB8500 USB Transceiver Driver"
14 depends on AB8500_CORE
17 Enable this to support the USB OTG transceiver in AB8500 chip.
18 This transceiver supports high and full speed devices plus,
19 in host mode, low speed.
22 bool "Freescale USB OTG Transceiver Driver"
23 depends on USB_EHCI_FSL && USB_FSL_USB2 && PM_RUNTIME
27 Enable this to support Freescale USB OTG transceiver.
30 tristate "Philips ISP1301 with OMAP OTG"
31 depends on I2C && ARCH_OMAP_OTG
34 If you say yes here you get support for the Philips ISP1301
35 USB-On-The-Go transceiver working with the OMAP OTG controller.
36 The ISP1301 is a full speed USB transceiver which is used in
37 products including H2, H3, and H4 development boards for Texas
38 Instruments OMAP processors.
40 This driver can also be built as a module. If so, the module
41 will be called isp1301_omap.
44 bool "Marvell USB 3.0 PHY controller Driver"
48 Enable this to support Marvell USB 3.0 phy controller for Marvell
52 tristate "NOP USB Transceiver Driver"
55 This driver is to be used by all the usb transceiver which are either
56 built-in with usb ip or which are autonomous and doesn't require any
57 phy programming such as ISP1x04 etc.
59 config OMAP_CONTROL_USB
60 tristate "OMAP CONTROL USB Driver"
62 Enable this to add support for the USB part present in the control
63 module. This driver has API to power on the USB2 PHY and to write to
64 the mailbox. The mailbox is present only in omap4 and the register to
65 power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
66 additional register to power on USB3 PHY.
69 tristate "OMAP USB2 PHY Driver"
70 depends on ARCH_OMAP2PLUS
71 select OMAP_CONTROL_USB
74 Enable this to support the transceiver that is part of SOC. This
75 driver takes care of all the PHY functionality apart from comparator.
76 The USB OTG controller communicates with the comparator using this
80 tristate "OMAP USB3 PHY Driver"
81 select OMAP_CONTROL_USB
84 Enable this to support the USB3 PHY that is part of SOC. This
85 driver takes care of all the PHY functionality apart from comparator.
86 This driver interacts with the "OMAP Control USB Driver" to power
92 Enable this to support Samsung USB phy helper driver for Samsung SoCs.
93 This driver provides common interface to interact, for Samsung USB 2.0 PHY
94 driver and later for Samsung USB 3.0 PHY driver.
96 config SAMSUNG_USB2PHY
97 tristate "Samsung USB 2.0 PHY controller Driver"
101 Enable this to support Samsung USB 2.0 (High Speed) PHY controller
102 driver for Samsung SoCs.
104 config SAMSUNG_USB3PHY
105 tristate "Samsung USB 3.0 PHY controller Driver"
106 select SAMSUNG_USBPHY
109 Enable this to support Samsung USB 3.0 (Super Speed) phy controller
113 tristate "TWL4030 USB Transceiver Driver"
114 depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
117 Enable this to support the USB OTG transceiver on TWL4030
118 family chips (including the TWL5030 and TPS659x0 devices).
119 This transceiver supports high and full speed devices plus,
120 in host mode, low speed.
123 tristate "TWL6030 USB Transceiver Driver"
124 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
126 Enable this to support the USB OTG transceiver on TWL6030
127 family chips. This TWL6030 transceiver has the VBUS and ID GND
128 and OTG SRP events capabilities. For all other transceiver functionality
129 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
130 are hooked to this driver through platform_data structure.
131 The definition of internal PHY APIs are in the mach-omap2 layer.
134 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
138 Provides simple GPIO VBUS sensing for controllers with an
139 internal transceiver via the usb_phy interface, and
140 optionally control of a D+ pullup GPIO as well as a VBUS
141 current limit regulator.
144 tristate "NXP ISP1301 USB transceiver support"
145 depends on USB || USB_GADGET
149 Say Y here to add support for the NXP ISP1301 USB transceiver driver.
150 This chip is typically used as USB transceiver for USB host, gadget
151 and OTG drivers (to be selected separately).
153 To compile this driver as a module, choose M here: the
154 module will be called isp1301.
157 tristate "OTG support for Qualcomm on-chip USB controller"
158 depends on (USB || USB_GADGET) && ARCH_MSM
161 Enable this to support the USB OTG transceiver on MSM chips. It
162 handles PHY initialization, clock management, and workarounds
163 required after resetting the hardware and power management.
164 This driver is required even for peripheral only or host only
166 This driver is not supported on boards like trout which
170 tristate "Marvell USB OTG support"
171 depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
175 Say Y here if you want to build Marvell USB OTG transciever
176 driver in kernel (including PXA and MMP series). This driver
177 implements role switch between EHCI host driver and gadget driver.
179 To compile this driver as a module, choose M here.
182 tristate "Freescale MXS USB PHY support"
183 depends on ARCH_MXC || ARCH_MXS
187 Enable this to support the Freescale MXS USB PHY.
189 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
192 tristate "Renesas R-Car USB PHY support"
193 depends on USB || USB_GADGET
196 Say Y here to add support for the Renesas R-Car USB common PHY driver.
197 This chip is typically used as USB PHY for USB host, gadget.
198 This driver supports R8A7778 and R8A7779.
200 To compile this driver as a module, choose M here: the
201 module will be called phy-rcar-usb.
204 bool "Generic ULPI Transceiver Driver"
207 Enable this to support ULPI connected USB OTG transceivers which
208 are likely found on embedded boards.
210 config USB_ULPI_VIEWPORT
214 Provides read/write operations to the ULPI phy register set for
215 controllers with a viewport register (e.g. Chipidea/ARC controllers).