1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
4 * Copyright (C) 2010 Freescale Semiconductor, Inc.
13 #include <asm/global_data.h>
14 #include <linux/compiler.h>
15 #include <linux/delay.h>
16 #include <usb/ehci-ci.h>
18 #include <asm/arch/imx-regs.h>
19 #include <asm/arch/clock.h>
20 #include <asm/mach-imx/iomux-v3.h>
21 #include <asm/mach-imx/sys_proto.h>
23 #include <asm/mach-types.h>
24 #include <power/regulator.h>
25 #include <linux/usb/otg.h>
29 DECLARE_GLOBAL_DATA_PTR;
31 #define USB_OTGREGS_OFFSET 0x000
32 #define USB_H1REGS_OFFSET 0x200
33 #define USB_H2REGS_OFFSET 0x400
34 #define USB_H3REGS_OFFSET 0x600
35 #define USB_OTHERREGS_OFFSET 0x800
37 #define USB_H1_CTRL_OFFSET 0x04
39 #define USBPHY_CTRL 0x00000030
40 #define USBPHY_CTRL_SET 0x00000034
41 #define USBPHY_CTRL_CLR 0x00000038
42 #define USBPHY_CTRL_TOG 0x0000003c
44 #define USBPHY_PWD 0x00000000
45 #define USBPHY_CTRL_SFTRST 0x80000000
46 #define USBPHY_CTRL_CLKGATE 0x40000000
47 #define USBPHY_CTRL_ENUTMILEVEL3 0x00008000
48 #define USBPHY_CTRL_ENUTMILEVEL2 0x00004000
49 #define USBPHY_CTRL_OTG_ID 0x08000000
51 #define ANADIG_USB2_CHRG_DETECT_EN_B 0x00100000
52 #define ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B 0x00080000
54 #define ANADIG_USB2_PLL_480_CTRL_BYPASS 0x00010000
55 #define ANADIG_USB2_PLL_480_CTRL_ENABLE 0x00002000
56 #define ANADIG_USB2_PLL_480_CTRL_POWER 0x00001000
57 #define ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS 0x00000040
59 #define USBNC_OFFSET 0x200
60 #define USBNC_PHY_STATUS_OFFSET 0x23C
61 #define USBNC_PHYSTATUS_ID_DIG (1 << 4) /* otg_id status */
62 #define USBNC_PHYCFG2_ACAENB (1 << 4) /* otg_id detection enable */
63 #define UCTRL_PWR_POL (1 << 9) /* OTG Polarity of Power Pin */
64 #define UCTRL_OVER_CUR_POL (1 << 8) /* OTG Polarity of Overcurrent */
65 #define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */
68 #define UCMD_RUN_STOP (1 << 0) /* controller run/stop */
69 #define UCMD_RESET (1 << 1) /* controller reset */
71 /* If this is not defined, assume MX6/MX7/MX8M SoC default */
72 #ifndef CONFIG_MXC_USB_PORTSC
73 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
76 /* Base address for this IP block is 0x02184800 */
78 u32 ctrl[4]; /* otg/host1-3 */
94 #if defined(CONFIG_MX6) && !defined(CONFIG_PHY)
95 static void usb_power_config_mx6(struct anatop_regs __iomem *anatop,
96 int anatop_bits_index)
98 void __iomem *chrg_detect;
99 void __iomem *pll_480_ctrl_clr;
100 void __iomem *pll_480_ctrl_set;
105 switch (anatop_bits_index) {
107 chrg_detect = &anatop->usb1_chrg_detect;
108 pll_480_ctrl_clr = &anatop->usb1_pll_480_ctrl_clr;
109 pll_480_ctrl_set = &anatop->usb1_pll_480_ctrl_set;
112 chrg_detect = &anatop->usb2_chrg_detect;
113 pll_480_ctrl_clr = &anatop->usb2_pll_480_ctrl_clr;
114 pll_480_ctrl_set = &anatop->usb2_pll_480_ctrl_set;
120 * Some phy and power's special controls
121 * 1. The external charger detector needs to be disabled
122 * or the signal at DP will be poor
123 * 2. The PLL's power and output to usb
124 * is totally controlled by IC, so the Software only needs
125 * to enable them at initializtion.
127 writel(ANADIG_USB2_CHRG_DETECT_EN_B |
128 ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
131 writel(ANADIG_USB2_PLL_480_CTRL_BYPASS,
134 writel(ANADIG_USB2_PLL_480_CTRL_ENABLE |
135 ANADIG_USB2_PLL_480_CTRL_POWER |
136 ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS,
140 static void __maybe_unused
141 usb_power_config_mx6(void *anatop, int anatop_bits_index) { }
144 #if defined(CONFIG_MX7) && !defined(CONFIG_PHY)
145 static void usb_power_config_mx7(struct usbnc_regs *usbnc)
147 void __iomem *phy_cfg2 = (void __iomem *)(&usbnc->phy_cfg2);
153 * Clear the ACAENB to enable usb_otg_id detection,
154 * otherwise it is the ACA detection enabled.
156 clrbits_le32(phy_cfg2, USBNC_PHYCFG2_ACAENB);
159 static void __maybe_unused
160 usb_power_config_mx7(void *usbnc) { }
163 #if defined(CONFIG_MX7ULP) && !defined(CONFIG_PHY)
164 static void usb_power_config_mx7ulp(struct usbphy_regs __iomem *usbphy)
169 writel(ANADIG_USB2_CHRG_DETECT_EN_B |
170 ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
171 &usbphy->usb1_chrg_detect);
173 scg_enable_usb_pll(true);
176 static void __maybe_unused
177 usb_power_config_mx7ulp(void *usbphy) { }
180 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
181 static const unsigned phy_bases[] = {
183 #if defined(USB_PHY1_BASE_ADDR)
188 #if !defined(CONFIG_PHY)
189 static void usb_internal_phy_clock_gate(void __iomem *phy_reg, int on)
191 phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
192 writel(USBPHY_CTRL_CLKGATE, phy_reg);
195 /* Return 0 : host node, <>0 : device mode */
196 static int usb_phy_enable(struct usb_ehci *ehci, void __iomem *phy_reg)
198 void __iomem *phy_ctrl;
199 void __iomem *usb_cmd;
202 phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
203 usb_cmd = (void __iomem *)&ehci->usbcmd;
205 /* Stop then Reset */
206 clrbits_le32(usb_cmd, UCMD_RUN_STOP);
207 ret = wait_for_bit_le32(usb_cmd, UCMD_RUN_STOP, false, 10000, false);
211 setbits_le32(usb_cmd, UCMD_RESET);
212 ret = wait_for_bit_le32(usb_cmd, UCMD_RESET, false, 10000, false);
216 /* Reset USBPHY module */
217 setbits_le32(phy_ctrl, USBPHY_CTRL_SFTRST);
220 /* Remove CLKGATE and SFTRST */
221 clrbits_le32(phy_ctrl, USBPHY_CTRL_CLKGATE | USBPHY_CTRL_SFTRST);
224 /* Power up the PHY */
225 writel(0, phy_reg + USBPHY_PWD);
226 /* enable FS/LS device */
227 setbits_le32(phy_ctrl, USBPHY_CTRL_ENUTMILEVEL2 |
228 USBPHY_CTRL_ENUTMILEVEL3);
234 int usb_phy_mode(int port)
236 void __iomem *phy_reg;
237 void __iomem *phy_ctrl;
240 phy_reg = (void __iomem *)phy_bases[port];
241 phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
243 val = readl(phy_ctrl);
245 if (val & USBPHY_CTRL_OTG_ID)
246 return USB_INIT_DEVICE;
248 return USB_INIT_HOST;
251 #elif defined(CONFIG_MX7)
252 int usb_phy_mode(int port)
254 struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
255 (0x10000 * port) + USBNC_OFFSET);
256 void __iomem *status = (void __iomem *)(&usbnc->phy_status);
261 if (val & USBNC_PHYSTATUS_ID_DIG)
262 return USB_INIT_DEVICE;
264 return USB_INIT_HOST;
268 #if !defined(CONFIG_PHY)
269 /* Should be done in the MXS PHY driver */
270 static void usb_oc_config(struct usbnc_regs *usbnc, int index)
272 void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
274 #if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
275 /* mx6qarm2 seems to required a different setting*/
276 clrbits_le32(ctrl, UCTRL_OVER_CUR_POL);
278 setbits_le32(ctrl, UCTRL_OVER_CUR_POL);
281 setbits_le32(ctrl, UCTRL_OVER_CUR_DIS);
283 /* Set power polarity to high active */
284 #ifdef CONFIG_MXC_USB_OTG_HACTIVE
285 setbits_le32(ctrl, UCTRL_PWR_POL);
287 clrbits_le32(ctrl, UCTRL_PWR_POL);
292 #if !CONFIG_IS_ENABLED(DM_USB)
294 * board_usb_phy_mode - override usb phy mode
295 * @port: usb host/otg port
297 * Target board specific, override usb_phy_mode.
298 * When usb-otg is used as usb host port, iomux pad usb_otg_id can be
299 * left disconnected in this case usb_phy_mode will not be able to identify
300 * the phy mode that usb port is used.
301 * Machine file overrides board_usb_phy_mode.
303 * Return: USB_INIT_DEVICE or USB_INIT_HOST
305 int __weak board_usb_phy_mode(int port)
307 return usb_phy_mode(port);
311 * board_ehci_hcd_init - set usb vbus voltage
312 * @port: usb otg port
314 * Target board specific, setup iomux pad to setup supply vbus voltage
315 * for usb otg port. Machine board file overrides board_ehci_hcd_init
319 int __weak board_ehci_hcd_init(int port)
325 * board_ehci_power - enables/disables usb vbus voltage
326 * @port: usb otg port
327 * @on: on/off vbus voltage
329 * Enables/disables supply vbus voltage for usb otg port.
330 * Machine board file overrides board_ehci_power
334 int __weak board_ehci_power(int port, int on)
339 int ehci_hcd_init(int index, enum usb_init_type init,
340 struct ehci_hccr **hccr, struct ehci_hcor **hcor)
342 enum usb_init_type type;
343 #if defined(CONFIG_MX6)
344 u32 controller_spacing = 0x200;
345 struct anatop_regs __iomem *anatop =
346 (struct anatop_regs __iomem *)ANATOP_BASE_ADDR;
347 struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
348 USB_OTHERREGS_OFFSET);
349 #elif defined(CONFIG_MX7)
350 u32 controller_spacing = 0x10000;
351 struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
352 (0x10000 * index) + USBNC_OFFSET);
353 #elif defined(CONFIG_MX7ULP)
354 u32 controller_spacing = 0x10000;
355 struct usbphy_regs __iomem *usbphy =
356 (struct usbphy_regs __iomem *)USB_PHY0_BASE_ADDR;
357 struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
358 (0x10000 * index) + USBNC_OFFSET);
360 struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR +
361 (controller_spacing * index));
367 if (CONFIG_IS_ENABLED(IMX_MODULE_FUSE)) {
368 if (usb_fused((ulong)ehci)) {
369 printf("SoC fuse indicates USB@0x%lx is unavailable.\n",
375 enable_usboh3_clk(1);
378 /* Do board specific initialization */
379 ret = board_ehci_hcd_init(index);
381 enable_usboh3_clk(0);
385 #if defined(CONFIG_MX6)
386 usb_power_config_mx6(anatop, index);
387 #elif defined (CONFIG_MX7)
388 usb_power_config_mx7(usbnc);
389 #elif defined (CONFIG_MX7ULP)
390 usb_power_config_mx7ulp(usbphy);
393 usb_oc_config(usbnc, index);
395 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
396 if (index < ARRAY_SIZE(phy_bases)) {
397 usb_internal_phy_clock_gate((void __iomem *)phy_bases[index], 1);
398 usb_phy_enable(ehci, (void __iomem *)phy_bases[index]);
402 type = board_usb_phy_mode(index);
405 *hccr = (struct ehci_hccr *)((uintptr_t)&ehci->caplength);
406 *hcor = (struct ehci_hcor *)((uintptr_t)*hccr +
407 HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
410 if ((type == init) || (type == USB_INIT_DEVICE))
411 board_ehci_power(index, (type == USB_INIT_DEVICE) ? 0 : 1);
414 if (type == USB_INIT_DEVICE)
417 setbits_le32(&ehci->usbmode, CM_HOST);
418 writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
419 setbits_le32(&ehci->portsc, USB_EN);
426 int ehci_hcd_stop(int index)
431 struct ehci_mx6_priv_data {
432 struct ehci_ctrl ctrl;
433 struct usb_ehci *ehci;
434 struct udevice *vbus_supply;
437 enum usb_init_type init_type;
438 #if !defined(CONFIG_PHY)
440 void __iomem *phy_addr;
441 void __iomem *misc_addr;
442 void __iomem *anatop_addr;
446 static int mx6_init_after_reset(struct ehci_ctrl *dev)
448 struct ehci_mx6_priv_data *priv = dev->priv;
449 enum usb_init_type type = priv->init_type;
450 struct usb_ehci *ehci = priv->ehci;
452 #if !defined(CONFIG_PHY)
453 usb_power_config_mx6(priv->anatop_addr, priv->portnr);
454 usb_power_config_mx7(priv->misc_addr);
455 usb_power_config_mx7ulp(priv->phy_addr);
457 usb_oc_config(priv->misc_addr, priv->portnr);
459 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
460 usb_internal_phy_clock_gate(priv->phy_addr, 1);
461 usb_phy_enable(ehci, priv->phy_addr);
465 #if CONFIG_IS_ENABLED(DM_REGULATOR)
466 if (priv->vbus_supply) {
468 ret = regulator_set_enable(priv->vbus_supply,
469 (type == USB_INIT_DEVICE) ?
471 if (ret && ret != -ENOSYS) {
472 printf("Error enabling VBUS supply (ret=%i)\n", ret);
478 if (type == USB_INIT_DEVICE)
481 setbits_le32(&ehci->usbmode, CM_HOST);
482 writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
483 setbits_le32(&ehci->portsc, USB_EN);
490 static const struct ehci_ops mx6_ehci_ops = {
491 .init_after_reset = mx6_init_after_reset
494 static int ehci_usb_phy_mode(struct udevice *dev)
496 struct usb_plat *plat = dev_get_plat(dev);
497 void *__iomem addr = dev_read_addr_ptr(dev);
498 void *__iomem phy_ctrl, *__iomem phy_status;
499 const void *blob = gd->fdt_blob;
500 int offset = dev_of_offset(dev), phy_off;
504 * About fsl,usbphy, Refer to
505 * Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt.
507 if (is_mx6() || is_mx7ulp()) {
508 phy_off = fdtdec_lookup_phandle(blob,
514 addr = (void __iomem *)fdtdec_get_addr(blob, phy_off,
516 if ((fdt_addr_t)addr == FDT_ADDR_T_NONE)
519 phy_ctrl = (void __iomem *)(addr + USBPHY_CTRL);
520 val = readl(phy_ctrl);
522 if (val & USBPHY_CTRL_OTG_ID)
523 plat->init_type = USB_INIT_DEVICE;
525 plat->init_type = USB_INIT_HOST;
526 } else if (is_mx7()) {
527 phy_status = (void __iomem *)(addr +
528 USBNC_PHY_STATUS_OFFSET);
529 val = readl(phy_status);
531 if (val & USBNC_PHYSTATUS_ID_DIG)
532 plat->init_type = USB_INIT_DEVICE;
534 plat->init_type = USB_INIT_HOST;
542 static int ehci_usb_of_to_plat(struct udevice *dev)
544 struct usb_plat *plat = dev_get_plat(dev);
545 enum usb_dr_mode dr_mode;
547 dr_mode = usb_get_dr_mode(dev_ofnode(dev));
550 case USB_DR_MODE_HOST:
551 plat->init_type = USB_INIT_HOST;
553 case USB_DR_MODE_PERIPHERAL:
554 plat->init_type = USB_INIT_DEVICE;
556 case USB_DR_MODE_OTG:
557 case USB_DR_MODE_UNKNOWN:
558 return ehci_usb_phy_mode(dev);
564 static int mx6_parse_dt_addrs(struct udevice *dev)
566 #if !defined(CONFIG_PHY)
567 struct ehci_mx6_priv_data *priv = dev_get_priv(dev);
568 int phy_off, misc_off;
569 const void *blob = gd->fdt_blob;
570 int offset = dev_of_offset(dev);
574 phy_off = fdtdec_lookup_phandle(blob, offset, "fsl,usbphy");
576 phy_off = fdtdec_lookup_phandle(blob, offset, "phys");
581 ret = fdtdec_get_alias_seq(blob, dev->uclass->uc_drv->name,
586 misc_off = fdtdec_lookup_phandle(blob, offset, "fsl,usbmisc");
590 addr = (void __iomem *)fdtdec_get_addr(blob, phy_off, "reg");
591 if ((fdt_addr_t)addr == FDT_ADDR_T_NONE)
594 priv->phy_addr = addr;
595 priv->portnr = devnump;
597 addr = (void __iomem *)fdtdec_get_addr(blob, misc_off, "reg");
598 if ((fdt_addr_t)addr == FDT_ADDR_T_NONE)
601 priv->misc_addr = addr;
603 #if defined(CONFIG_MX6)
606 /* Resolve ANATOP offset through USB PHY node */
607 anatop_off = fdtdec_lookup_phandle(blob, phy_off, "fsl,anatop");
611 addr = (void __iomem *)fdtdec_get_addr(blob, anatop_off, "reg");
612 if ((fdt_addr_t)addr == FDT_ADDR_T_NONE)
615 priv->anatop_addr = addr;
621 static int ehci_usb_probe(struct udevice *dev)
623 struct usb_plat *plat = dev_get_plat(dev);
624 struct usb_ehci *ehci = dev_read_addr_ptr(dev);
625 struct ehci_mx6_priv_data *priv = dev_get_priv(dev);
626 enum usb_init_type type = plat->init_type;
627 struct ehci_hccr *hccr;
628 struct ehci_hcor *hcor;
631 if (CONFIG_IS_ENABLED(IMX_MODULE_FUSE)) {
632 if (usb_fused((ulong)ehci)) {
633 printf("SoC fuse indicates USB@0x%lx is unavailable.\n",
639 ret = mx6_parse_dt_addrs(dev);
644 priv->init_type = type;
646 #if CONFIG_IS_ENABLED(CLK)
647 ret = clk_get_by_index(dev, 0, &priv->clk);
651 ret = clk_enable(&priv->clk);
655 /* Compatibility with DM_USB and !CLK */
656 enable_usboh3_clk(1);
660 #if CONFIG_IS_ENABLED(DM_REGULATOR)
661 ret = device_get_supply_regulator(dev, "vbus-supply",
664 debug("%s: No vbus supply\n", dev->name);
667 #if !defined(CONFIG_PHY)
668 usb_power_config_mx6(priv->anatop_addr, priv->portnr);
669 usb_power_config_mx7(priv->misc_addr);
670 usb_power_config_mx7ulp(priv->phy_addr);
672 usb_oc_config(priv->misc_addr, priv->portnr);
674 #if defined(CONFIG_MX6) || defined(CONFIG_MX7ULP)
675 usb_internal_phy_clock_gate(priv->phy_addr, 1);
676 usb_phy_enable(ehci, priv->phy_addr);
680 #if CONFIG_IS_ENABLED(DM_REGULATOR)
681 if (priv->vbus_supply) {
682 ret = regulator_set_enable(priv->vbus_supply,
683 (type == USB_INIT_DEVICE) ?
685 if (ret && ret != -ENOSYS) {
686 printf("Error enabling VBUS supply (ret=%i)\n", ret);
692 if (priv->init_type == USB_INIT_HOST) {
693 setbits_le32(&ehci->usbmode, CM_HOST);
694 writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
695 setbits_le32(&ehci->portsc, USB_EN);
700 #if defined(CONFIG_PHY)
701 ret = ehci_setup_phy(dev, &priv->phy, 0);
706 hccr = (struct ehci_hccr *)((uintptr_t)&ehci->caplength);
707 hcor = (struct ehci_hcor *)((uintptr_t)hccr +
708 HC_LENGTH(ehci_readl(&(hccr)->cr_capbase)));
710 ret = ehci_register(dev, hccr, hcor, &mx6_ehci_ops, 0, priv->init_type);
717 #if defined(CONFIG_PHY)
718 ehci_shutdown_phy(dev, &priv->phy);
721 #if CONFIG_IS_ENABLED(DM_REGULATOR)
722 if (priv->vbus_supply)
723 regulator_set_enable(priv->vbus_supply, false);
726 #if CONFIG_IS_ENABLED(CLK)
727 clk_disable(&priv->clk);
729 /* Compatibility with DM_USB and !CLK */
730 enable_usboh3_clk(0);
735 int ehci_usb_remove(struct udevice *dev)
737 struct ehci_mx6_priv_data *priv __maybe_unused = dev_get_priv(dev);
739 ehci_deregister(dev);
741 #if defined(CONFIG_PHY)
742 ehci_shutdown_phy(dev, &priv->phy);
745 #if CONFIG_IS_ENABLED(DM_REGULATOR)
746 if (priv->vbus_supply)
747 regulator_set_enable(priv->vbus_supply, false);
750 #if CONFIG_IS_ENABLED(CLK)
751 clk_disable(&priv->clk);
757 static const struct udevice_id mx6_usb_ids[] = {
758 { .compatible = "fsl,imx27-usb" },
759 { .compatible = "fsl,imx7d-usb" },
763 U_BOOT_DRIVER(usb_mx6) = {
766 .of_match = mx6_usb_ids,
767 .of_to_plat = ehci_usb_of_to_plat,
768 .probe = ehci_usb_probe,
769 .remove = ehci_usb_remove,
770 .ops = &ehci_usb_ops,
771 .plat_auto = sizeof(struct usb_plat),
772 .priv_auto = sizeof(struct ehci_mx6_priv_data),
773 .flags = DM_FLAG_ALLOC_PRIV_DMA,