1 // SPDX-License-Identifier: GPL-2.0
3 * core.c - DesignWare USB3 DRD Controller Core file
5 * Copyright (C) 2010-2011 Texas Instruments Incorporated - https://www.ti.com
7 * Authors: Felipe Balbi <balbi@ti.com>,
8 * Sebastian Andrzej Siewior <bigeasy@linutronix.de>
11 #include <linux/clk.h>
12 #include <linux/version.h>
13 #include <linux/module.h>
14 #include <linux/kernel.h>
15 #include <linux/slab.h>
16 #include <linux/spinlock.h>
17 #include <linux/platform_device.h>
18 #include <linux/pm_runtime.h>
19 #include <linux/interrupt.h>
20 #include <linux/ioport.h>
22 #include <linux/list.h>
23 #include <linux/delay.h>
24 #include <linux/dma-mapping.h>
26 #include <linux/of_graph.h>
27 #include <linux/acpi.h>
28 #include <linux/pinctrl/consumer.h>
29 #include <linux/reset.h>
30 #include <linux/bitfield.h>
32 #include <linux/usb/ch9.h>
33 #include <linux/usb/gadget.h>
34 #include <linux/usb/of.h>
35 #include <linux/usb/otg.h>
43 #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */
46 * dwc3_get_dr_mode - Validates and sets dr_mode
47 * @dwc: pointer to our context structure
49 static int dwc3_get_dr_mode(struct dwc3 *dwc)
51 enum usb_dr_mode mode;
52 struct device *dev = dwc->dev;
55 if (dwc->dr_mode == USB_DR_MODE_UNKNOWN)
56 dwc->dr_mode = USB_DR_MODE_OTG;
59 hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0);
62 case DWC3_GHWPARAMS0_MODE_GADGET:
63 if (IS_ENABLED(CONFIG_USB_DWC3_HOST)) {
65 "Controller does not support host mode.\n");
68 mode = USB_DR_MODE_PERIPHERAL;
70 case DWC3_GHWPARAMS0_MODE_HOST:
71 if (IS_ENABLED(CONFIG_USB_DWC3_GADGET)) {
73 "Controller does not support device mode.\n");
76 mode = USB_DR_MODE_HOST;
79 if (IS_ENABLED(CONFIG_USB_DWC3_HOST))
80 mode = USB_DR_MODE_HOST;
81 else if (IS_ENABLED(CONFIG_USB_DWC3_GADGET))
82 mode = USB_DR_MODE_PERIPHERAL;
85 * DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG
86 * mode. If the controller supports DRD but the dr_mode is not
87 * specified or set to OTG, then set the mode to peripheral.
89 if (mode == USB_DR_MODE_OTG && !dwc->edev &&
90 (!IS_ENABLED(CONFIG_USB_ROLE_SWITCH) ||
91 !device_property_read_bool(dwc->dev, "usb-role-switch")) &&
92 !DWC3_VER_IS_PRIOR(DWC3, 330A))
93 mode = USB_DR_MODE_PERIPHERAL;
96 if (mode != dwc->dr_mode) {
98 "Configuration mismatch. dr_mode forced to %s\n",
99 mode == USB_DR_MODE_HOST ? "host" : "gadget");
107 void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode)
111 reg = dwc3_readl(dwc->regs, DWC3_GCTL);
112 reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
113 reg |= DWC3_GCTL_PRTCAPDIR(mode);
114 dwc3_writel(dwc->regs, DWC3_GCTL, reg);
116 dwc->current_dr_role = mode;
119 static void __dwc3_set_mode(struct work_struct *work)
121 struct dwc3 *dwc = work_to_dwc(work);
127 mutex_lock(&dwc->mutex);
128 spin_lock_irqsave(&dwc->lock, flags);
129 desired_dr_role = dwc->desired_dr_role;
130 spin_unlock_irqrestore(&dwc->lock, flags);
132 pm_runtime_get_sync(dwc->dev);
134 if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_OTG)
135 dwc3_otg_update(dwc, 0);
137 if (!desired_dr_role)
140 if (desired_dr_role == dwc->current_dr_role)
143 if (desired_dr_role == DWC3_GCTL_PRTCAP_OTG && dwc->edev)
146 switch (dwc->current_dr_role) {
147 case DWC3_GCTL_PRTCAP_HOST:
150 case DWC3_GCTL_PRTCAP_DEVICE:
151 dwc3_gadget_exit(dwc);
152 dwc3_event_buffers_cleanup(dwc);
154 case DWC3_GCTL_PRTCAP_OTG:
156 spin_lock_irqsave(&dwc->lock, flags);
157 dwc->desired_otg_role = DWC3_OTG_ROLE_IDLE;
158 spin_unlock_irqrestore(&dwc->lock, flags);
159 dwc3_otg_update(dwc, 1);
166 * When current_dr_role is not set, there's no role switching.
167 * Only perform GCTL.CoreSoftReset when there's DRD role switching.
169 if (dwc->current_dr_role && ((DWC3_IP_IS(DWC3) ||
170 DWC3_VER_IS_PRIOR(DWC31, 190A)) &&
171 desired_dr_role != DWC3_GCTL_PRTCAP_OTG)) {
172 reg = dwc3_readl(dwc->regs, DWC3_GCTL);
173 reg |= DWC3_GCTL_CORESOFTRESET;
174 dwc3_writel(dwc->regs, DWC3_GCTL, reg);
177 * Wait for internal clocks to synchronized. DWC_usb31 and
178 * DWC_usb32 may need at least 50ms (less for DWC_usb3). To
179 * keep it consistent across different IPs, let's wait up to
180 * 100ms before clearing GCTL.CORESOFTRESET.
184 reg = dwc3_readl(dwc->regs, DWC3_GCTL);
185 reg &= ~DWC3_GCTL_CORESOFTRESET;
186 dwc3_writel(dwc->regs, DWC3_GCTL, reg);
189 spin_lock_irqsave(&dwc->lock, flags);
191 dwc3_set_prtcap(dwc, desired_dr_role);
193 spin_unlock_irqrestore(&dwc->lock, flags);
195 switch (desired_dr_role) {
196 case DWC3_GCTL_PRTCAP_HOST:
197 ret = dwc3_host_init(dwc);
199 dev_err(dwc->dev, "failed to initialize host\n");
202 otg_set_vbus(dwc->usb2_phy->otg, true);
203 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST);
204 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_HOST);
205 if (dwc->dis_split_quirk) {
206 reg = dwc3_readl(dwc->regs, DWC3_GUCTL3);
207 reg |= DWC3_GUCTL3_SPLITDISABLE;
208 dwc3_writel(dwc->regs, DWC3_GUCTL3, reg);
212 case DWC3_GCTL_PRTCAP_DEVICE:
213 dwc3_core_soft_reset(dwc);
215 dwc3_event_buffers_setup(dwc);
218 otg_set_vbus(dwc->usb2_phy->otg, false);
219 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_DEVICE);
220 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_DEVICE);
222 ret = dwc3_gadget_init(dwc);
224 dev_err(dwc->dev, "failed to initialize peripheral\n");
226 case DWC3_GCTL_PRTCAP_OTG:
228 dwc3_otg_update(dwc, 0);
235 pm_runtime_mark_last_busy(dwc->dev);
236 pm_runtime_put_autosuspend(dwc->dev);
237 mutex_unlock(&dwc->mutex);
240 void dwc3_set_mode(struct dwc3 *dwc, u32 mode)
244 if (dwc->dr_mode != USB_DR_MODE_OTG)
247 spin_lock_irqsave(&dwc->lock, flags);
248 dwc->desired_dr_role = mode;
249 spin_unlock_irqrestore(&dwc->lock, flags);
251 queue_work(system_freezable_wq, &dwc->drd_work);
254 u32 dwc3_core_fifo_space(struct dwc3_ep *dep, u8 type)
256 struct dwc3 *dwc = dep->dwc;
259 dwc3_writel(dwc->regs, DWC3_GDBGFIFOSPACE,
260 DWC3_GDBGFIFOSPACE_NUM(dep->number) |
261 DWC3_GDBGFIFOSPACE_TYPE(type));
263 reg = dwc3_readl(dwc->regs, DWC3_GDBGFIFOSPACE);
265 return DWC3_GDBGFIFOSPACE_SPACE_AVAILABLE(reg);
269 * dwc3_core_soft_reset - Issues core soft reset and PHY reset
270 * @dwc: pointer to our context structure
272 int dwc3_core_soft_reset(struct dwc3 *dwc)
278 * We're resetting only the device side because, if we're in host mode,
279 * XHCI driver will reset the host block. If dwc3 was configured for
280 * host-only mode or current role is host, then we can return early.
282 if (dwc->dr_mode == USB_DR_MODE_HOST || dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST)
285 reg = dwc3_readl(dwc->regs, DWC3_DCTL);
286 reg |= DWC3_DCTL_CSFTRST;
287 reg &= ~DWC3_DCTL_RUN_STOP;
288 dwc3_gadget_dctl_write_safe(dwc, reg);
291 * For DWC_usb31 controller 1.90a and later, the DCTL.CSFRST bit
292 * is cleared only after all the clocks are synchronized. This can
293 * take a little more than 50ms. Set the polling rate at 20ms
294 * for 10 times instead.
296 if (DWC3_VER_IS_WITHIN(DWC31, 190A, ANY) || DWC3_IP_IS(DWC32))
300 reg = dwc3_readl(dwc->regs, DWC3_DCTL);
301 if (!(reg & DWC3_DCTL_CSFTRST))
304 if (DWC3_VER_IS_WITHIN(DWC31, 190A, ANY) || DWC3_IP_IS(DWC32))
310 dev_warn(dwc->dev, "DWC3 controller soft reset failed.\n");
315 * For DWC_usb31 controller 1.80a and prior, once DCTL.CSFRST bit
316 * is cleared, we must wait at least 50ms before accessing the PHY
317 * domain (synchronization delay).
319 if (DWC3_VER_IS_WITHIN(DWC31, ANY, 180A))
326 * dwc3_frame_length_adjustment - Adjusts frame length if required
327 * @dwc3: Pointer to our controller context structure
329 static void dwc3_frame_length_adjustment(struct dwc3 *dwc)
334 if (DWC3_VER_IS_PRIOR(DWC3, 250A))
340 reg = dwc3_readl(dwc->regs, DWC3_GFLADJ);
341 dft = reg & DWC3_GFLADJ_30MHZ_MASK;
342 if (dft != dwc->fladj) {
343 reg &= ~DWC3_GFLADJ_30MHZ_MASK;
344 reg |= DWC3_GFLADJ_30MHZ_SDBND_SEL | dwc->fladj;
345 dwc3_writel(dwc->regs, DWC3_GFLADJ, reg);
350 * dwc3_ref_clk_period - Reference clock period configuration
351 * Default reference clock period depends on hardware
352 * configuration. For systems with reference clock that differs
353 * from the default, this will set clock period in DWC3_GUCTL
355 * @dwc: Pointer to our controller context structure
357 static void dwc3_ref_clk_period(struct dwc3 *dwc)
359 unsigned long period;
366 rate = clk_get_rate(dwc->ref_clk);
369 period = NSEC_PER_SEC / rate;
370 } else if (dwc->ref_clk_per) {
371 period = dwc->ref_clk_per;
372 rate = NSEC_PER_SEC / period;
377 reg = dwc3_readl(dwc->regs, DWC3_GUCTL);
378 reg &= ~DWC3_GUCTL_REFCLKPER_MASK;
379 reg |= FIELD_PREP(DWC3_GUCTL_REFCLKPER_MASK, period);
380 dwc3_writel(dwc->regs, DWC3_GUCTL, reg);
382 if (DWC3_VER_IS_PRIOR(DWC3, 250A))
386 * The calculation below is
388 * 125000 * (NSEC_PER_SEC / (rate * period) - 1)
390 * but rearranged for fixed-point arithmetic. The division must be
391 * 64-bit because 125000 * NSEC_PER_SEC doesn't fit in 32 bits (and
392 * neither does rate * period).
394 * Note that rate * period ~= NSEC_PER_SECOND, minus the number of
395 * nanoseconds of error caused by the truncation which happened during
396 * the division when calculating rate or period (whichever one was
397 * derived from the other). We first calculate the relative error, then
398 * scale it to units of 8 ppm.
400 fladj = div64_u64(125000ULL * NSEC_PER_SEC, (u64)rate * period);
404 * The documented 240MHz constant is scaled by 2 to get PLS1 as well.
406 decr = 480000000 / rate;
408 reg = dwc3_readl(dwc->regs, DWC3_GFLADJ);
409 reg &= ~DWC3_GFLADJ_REFCLK_FLADJ_MASK
410 & ~DWC3_GFLADJ_240MHZDECR
411 & ~DWC3_GFLADJ_240MHZDECR_PLS1;
412 reg |= FIELD_PREP(DWC3_GFLADJ_REFCLK_FLADJ_MASK, fladj)
413 | FIELD_PREP(DWC3_GFLADJ_240MHZDECR, decr >> 1)
414 | FIELD_PREP(DWC3_GFLADJ_240MHZDECR_PLS1, decr & 1);
416 if (dwc->gfladj_refclk_lpm_sel)
417 reg |= DWC3_GFLADJ_REFCLK_LPM_SEL;
419 dwc3_writel(dwc->regs, DWC3_GFLADJ, reg);
423 * dwc3_free_one_event_buffer - Frees one event buffer
424 * @dwc: Pointer to our controller context structure
425 * @evt: Pointer to event buffer to be freed
427 static void dwc3_free_one_event_buffer(struct dwc3 *dwc,
428 struct dwc3_event_buffer *evt)
430 dma_free_coherent(dwc->sysdev, evt->length, evt->buf, evt->dma);
434 * dwc3_alloc_one_event_buffer - Allocates one event buffer structure
435 * @dwc: Pointer to our controller context structure
436 * @length: size of the event buffer
438 * Returns a pointer to the allocated event buffer structure on success
439 * otherwise ERR_PTR(errno).
441 static struct dwc3_event_buffer *dwc3_alloc_one_event_buffer(struct dwc3 *dwc,
444 struct dwc3_event_buffer *evt;
446 evt = devm_kzalloc(dwc->dev, sizeof(*evt), GFP_KERNEL);
448 return ERR_PTR(-ENOMEM);
451 evt->length = length;
452 evt->cache = devm_kzalloc(dwc->dev, length, GFP_KERNEL);
454 return ERR_PTR(-ENOMEM);
456 evt->buf = dma_alloc_coherent(dwc->sysdev, length,
457 &evt->dma, GFP_KERNEL);
459 return ERR_PTR(-ENOMEM);
465 * dwc3_free_event_buffers - frees all allocated event buffers
466 * @dwc: Pointer to our controller context structure
468 static void dwc3_free_event_buffers(struct dwc3 *dwc)
470 struct dwc3_event_buffer *evt;
474 dwc3_free_one_event_buffer(dwc, evt);
478 * dwc3_alloc_event_buffers - Allocates @num event buffers of size @length
479 * @dwc: pointer to our controller context structure
480 * @length: size of event buffer
482 * Returns 0 on success otherwise negative errno. In the error case, dwc
483 * may contain some buffers allocated but not all which were requested.
485 static int dwc3_alloc_event_buffers(struct dwc3 *dwc, unsigned int length)
487 struct dwc3_event_buffer *evt;
489 evt = dwc3_alloc_one_event_buffer(dwc, length);
491 dev_err(dwc->dev, "can't allocate event buffer\n");
500 * dwc3_event_buffers_setup - setup our allocated event buffers
501 * @dwc: pointer to our controller context structure
503 * Returns 0 on success otherwise negative errno.
505 int dwc3_event_buffers_setup(struct dwc3 *dwc)
507 struct dwc3_event_buffer *evt;
511 dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0),
512 lower_32_bits(evt->dma));
513 dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0),
514 upper_32_bits(evt->dma));
515 dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0),
516 DWC3_GEVNTSIZ_SIZE(evt->length));
517 dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0);
522 void dwc3_event_buffers_cleanup(struct dwc3 *dwc)
524 struct dwc3_event_buffer *evt;
530 dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0), 0);
531 dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0), 0);
532 dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), DWC3_GEVNTSIZ_INTMASK
533 | DWC3_GEVNTSIZ_SIZE(0));
534 dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0);
537 static void dwc3_core_num_eps(struct dwc3 *dwc)
539 struct dwc3_hwparams *parms = &dwc->hwparams;
541 dwc->num_eps = DWC3_NUM_EPS(parms);
544 static void dwc3_cache_hwparams(struct dwc3 *dwc)
546 struct dwc3_hwparams *parms = &dwc->hwparams;
548 parms->hwparams0 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS0);
549 parms->hwparams1 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS1);
550 parms->hwparams2 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS2);
551 parms->hwparams3 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS3);
552 parms->hwparams4 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS4);
553 parms->hwparams5 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS5);
554 parms->hwparams6 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS6);
555 parms->hwparams7 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS7);
556 parms->hwparams8 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS8);
558 if (DWC3_IP_IS(DWC32))
559 parms->hwparams9 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS9);
562 static int dwc3_core_ulpi_init(struct dwc3 *dwc)
567 intf = DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3);
569 if (intf == DWC3_GHWPARAMS3_HSPHY_IFC_ULPI ||
570 (intf == DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI &&
571 dwc->hsphy_interface &&
572 !strncmp(dwc->hsphy_interface, "ulpi", 4)))
573 ret = dwc3_ulpi_init(dwc);
579 * dwc3_phy_setup - Configure USB PHY Interface of DWC3 Core
580 * @dwc: Pointer to our controller context structure
582 * Returns 0 on success. The USB PHY interfaces are configured but not
583 * initialized. The PHY interfaces and the PHYs get initialized together with
584 * the core in dwc3_core_init.
586 static int dwc3_phy_setup(struct dwc3 *dwc)
588 unsigned int hw_mode;
591 hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0);
593 reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
596 * Make sure UX_EXIT_PX is cleared as that causes issues with some
597 * PHYs. Also, this bit is not supposed to be used in normal operation.
599 reg &= ~DWC3_GUSB3PIPECTL_UX_EXIT_PX;
602 * Above 1.94a, it is recommended to set DWC3_GUSB3PIPECTL_SUSPHY
603 * to '0' during coreConsultant configuration. So default value
604 * will be '0' when the core is reset. Application needs to set it
605 * to '1' after the core initialization is completed.
607 if (!DWC3_VER_IS_WITHIN(DWC3, ANY, 194A))
608 reg |= DWC3_GUSB3PIPECTL_SUSPHY;
611 * For DRD controllers, GUSB3PIPECTL.SUSPENDENABLE must be cleared after
612 * power-on reset, and it can be set after core initialization, which is
613 * after device soft-reset during initialization.
615 if (hw_mode == DWC3_GHWPARAMS0_MODE_DRD)
616 reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
618 if (dwc->u2ss_inp3_quirk)
619 reg |= DWC3_GUSB3PIPECTL_U2SSINP3OK;
621 if (dwc->dis_rxdet_inp3_quirk)
622 reg |= DWC3_GUSB3PIPECTL_DISRXDETINP3;
624 if (dwc->req_p1p2p3_quirk)
625 reg |= DWC3_GUSB3PIPECTL_REQP1P2P3;
627 if (dwc->del_p1p2p3_quirk)
628 reg |= DWC3_GUSB3PIPECTL_DEP1P2P3_EN;
630 if (dwc->del_phy_power_chg_quirk)
631 reg |= DWC3_GUSB3PIPECTL_DEPOCHANGE;
633 if (dwc->lfps_filter_quirk)
634 reg |= DWC3_GUSB3PIPECTL_LFPSFILT;
636 if (dwc->rx_detect_poll_quirk)
637 reg |= DWC3_GUSB3PIPECTL_RX_DETOPOLL;
639 if (dwc->tx_de_emphasis_quirk)
640 reg |= DWC3_GUSB3PIPECTL_TX_DEEPH(dwc->tx_de_emphasis);
642 if (dwc->dis_u3_susphy_quirk)
643 reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
645 if (dwc->dis_del_phy_power_chg_quirk)
646 reg &= ~DWC3_GUSB3PIPECTL_DEPOCHANGE;
648 dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
650 reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
652 /* Select the HS PHY interface */
653 switch (DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3)) {
654 case DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI:
655 if (dwc->hsphy_interface &&
656 !strncmp(dwc->hsphy_interface, "utmi", 4)) {
657 reg &= ~DWC3_GUSB2PHYCFG_ULPI_UTMI;
659 } else if (dwc->hsphy_interface &&
660 !strncmp(dwc->hsphy_interface, "ulpi", 4)) {
661 reg |= DWC3_GUSB2PHYCFG_ULPI_UTMI;
662 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
664 /* Relying on default value. */
665 if (!(reg & DWC3_GUSB2PHYCFG_ULPI_UTMI))
669 case DWC3_GHWPARAMS3_HSPHY_IFC_ULPI:
674 switch (dwc->hsphy_mode) {
675 case USBPHY_INTERFACE_MODE_UTMI:
676 reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK |
677 DWC3_GUSB2PHYCFG_USBTRDTIM_MASK);
678 reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_8_BIT) |
679 DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_8_BIT);
681 case USBPHY_INTERFACE_MODE_UTMIW:
682 reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK |
683 DWC3_GUSB2PHYCFG_USBTRDTIM_MASK);
684 reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_16_BIT) |
685 DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_16_BIT);
692 * Above 1.94a, it is recommended to set DWC3_GUSB2PHYCFG_SUSPHY to
693 * '0' during coreConsultant configuration. So default value will
694 * be '0' when the core is reset. Application needs to set it to
695 * '1' after the core initialization is completed.
697 if (!DWC3_VER_IS_WITHIN(DWC3, ANY, 194A))
698 reg |= DWC3_GUSB2PHYCFG_SUSPHY;
701 * For DRD controllers, GUSB2PHYCFG.SUSPHY must be cleared after
702 * power-on reset, and it can be set after core initialization, which is
703 * after device soft-reset during initialization.
705 if (hw_mode == DWC3_GHWPARAMS0_MODE_DRD)
706 reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
708 if (dwc->dis_u2_susphy_quirk)
709 reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
711 if (dwc->dis_enblslpm_quirk)
712 reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
714 reg |= DWC3_GUSB2PHYCFG_ENBLSLPM;
716 if (dwc->dis_u2_freeclk_exists_quirk || dwc->gfladj_refclk_lpm_sel)
717 reg &= ~DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS;
720 * Some ULPI USB PHY does not support internal VBUS supply, to drive
721 * the CPEN pin requires the configuration of the ULPI DRVVBUSEXTERNAL
722 * bit of OTG_CTRL register. Controller configures the USB2 PHY
723 * ULPIEXTVBUSDRV bit[17] of the GUSB2PHYCFG register to drive vBus
724 * with an external supply.
726 if (dwc->ulpi_ext_vbus_drv)
727 reg |= DWC3_GUSB2PHYCFG_ULPIEXTVBUSDRV;
729 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
734 static int dwc3_phy_init(struct dwc3 *dwc)
738 usb_phy_init(dwc->usb2_phy);
739 usb_phy_init(dwc->usb3_phy);
741 ret = phy_init(dwc->usb2_generic_phy);
743 goto err_shutdown_usb3_phy;
745 ret = phy_init(dwc->usb3_generic_phy);
747 goto err_exit_usb2_phy;
752 phy_exit(dwc->usb2_generic_phy);
753 err_shutdown_usb3_phy:
754 usb_phy_shutdown(dwc->usb3_phy);
755 usb_phy_shutdown(dwc->usb2_phy);
760 static void dwc3_phy_exit(struct dwc3 *dwc)
762 phy_exit(dwc->usb3_generic_phy);
763 phy_exit(dwc->usb2_generic_phy);
765 usb_phy_shutdown(dwc->usb3_phy);
766 usb_phy_shutdown(dwc->usb2_phy);
769 static int dwc3_phy_power_on(struct dwc3 *dwc)
773 usb_phy_set_suspend(dwc->usb2_phy, 0);
774 usb_phy_set_suspend(dwc->usb3_phy, 0);
776 ret = phy_power_on(dwc->usb2_generic_phy);
778 goto err_suspend_usb3_phy;
780 ret = phy_power_on(dwc->usb3_generic_phy);
782 goto err_power_off_usb2_phy;
786 err_power_off_usb2_phy:
787 phy_power_off(dwc->usb2_generic_phy);
788 err_suspend_usb3_phy:
789 usb_phy_set_suspend(dwc->usb3_phy, 1);
790 usb_phy_set_suspend(dwc->usb2_phy, 1);
795 static void dwc3_phy_power_off(struct dwc3 *dwc)
797 phy_power_off(dwc->usb3_generic_phy);
798 phy_power_off(dwc->usb2_generic_phy);
800 usb_phy_set_suspend(dwc->usb3_phy, 1);
801 usb_phy_set_suspend(dwc->usb2_phy, 1);
804 static int dwc3_clk_enable(struct dwc3 *dwc)
808 ret = clk_prepare_enable(dwc->bus_clk);
812 ret = clk_prepare_enable(dwc->ref_clk);
814 goto disable_bus_clk;
816 ret = clk_prepare_enable(dwc->susp_clk);
818 goto disable_ref_clk;
823 clk_disable_unprepare(dwc->ref_clk);
825 clk_disable_unprepare(dwc->bus_clk);
829 static void dwc3_clk_disable(struct dwc3 *dwc)
831 clk_disable_unprepare(dwc->susp_clk);
832 clk_disable_unprepare(dwc->ref_clk);
833 clk_disable_unprepare(dwc->bus_clk);
836 static void dwc3_core_exit(struct dwc3 *dwc)
838 dwc3_event_buffers_cleanup(dwc);
839 dwc3_phy_power_off(dwc);
841 dwc3_clk_disable(dwc);
842 reset_control_assert(dwc->reset);
845 static bool dwc3_core_is_valid(struct dwc3 *dwc)
849 reg = dwc3_readl(dwc->regs, DWC3_GSNPSID);
850 dwc->ip = DWC3_GSNPS_ID(reg);
852 /* This should read as U3 followed by revision number */
853 if (DWC3_IP_IS(DWC3)) {
855 } else if (DWC3_IP_IS(DWC31) || DWC3_IP_IS(DWC32)) {
856 dwc->revision = dwc3_readl(dwc->regs, DWC3_VER_NUMBER);
857 dwc->version_type = dwc3_readl(dwc->regs, DWC3_VER_TYPE);
865 static void dwc3_core_setup_global_control(struct dwc3 *dwc)
869 reg = dwc3_readl(dwc->regs, DWC3_GCTL);
870 reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
872 switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc->hwparams.hwparams1)) {
873 case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
875 * WORKAROUND: DWC3 revisions between 2.10a and 2.50a have an
876 * issue which would cause xHCI compliance tests to fail.
878 * Because of that we cannot enable clock gating on such
883 * STAR#9000588375: Clock Gating, SOF Issues when ref_clk-Based
886 if ((dwc->dr_mode == USB_DR_MODE_HOST ||
887 dwc->dr_mode == USB_DR_MODE_OTG) &&
888 DWC3_VER_IS_WITHIN(DWC3, 210A, 250A))
889 reg |= DWC3_GCTL_DSBLCLKGTNG | DWC3_GCTL_SOFITPSYNC;
891 reg &= ~DWC3_GCTL_DSBLCLKGTNG;
893 case DWC3_GHWPARAMS1_EN_PWROPT_HIB:
895 * REVISIT Enabling this bit so that host-mode hibernation
896 * will work. Device-mode hibernation is not yet implemented.
898 reg |= DWC3_GCTL_GBLHIBERNATIONEN;
905 /* check if current dwc3 is on simulation board */
906 if (dwc->hwparams.hwparams6 & DWC3_GHWPARAMS6_EN_FPGA) {
907 dev_info(dwc->dev, "Running with FPGA optimizations\n");
911 WARN_ONCE(dwc->disable_scramble_quirk && !dwc->is_fpga,
912 "disable_scramble cannot be used on non-FPGA builds\n");
914 if (dwc->disable_scramble_quirk && dwc->is_fpga)
915 reg |= DWC3_GCTL_DISSCRAMBLE;
917 reg &= ~DWC3_GCTL_DISSCRAMBLE;
919 if (dwc->u2exit_lfps_quirk)
920 reg |= DWC3_GCTL_U2EXIT_LFPS;
923 * WORKAROUND: DWC3 revisions <1.90a have a bug
924 * where the device can fail to connect at SuperSpeed
925 * and falls back to high-speed mode which causes
926 * the device to enter a Connect/Disconnect loop
928 if (DWC3_VER_IS_PRIOR(DWC3, 190A))
929 reg |= DWC3_GCTL_U2RSTECN;
931 dwc3_writel(dwc->regs, DWC3_GCTL, reg);
934 static int dwc3_core_get_phy(struct dwc3 *dwc);
935 static int dwc3_core_ulpi_init(struct dwc3 *dwc);
937 /* set global incr burst type configuration registers */
938 static void dwc3_set_incr_burst_type(struct dwc3 *dwc)
940 struct device *dev = dwc->dev;
941 /* incrx_mode : for INCR burst type. */
943 /* incrx_size : for size of INCRX burst. */
951 cfg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0);
954 * Handle property "snps,incr-burst-type-adjustment".
955 * Get the number of value from this property:
956 * result <= 0, means this property is not supported.
957 * result = 1, means INCRx burst mode supported.
958 * result > 1, means undefined length burst mode supported.
960 ntype = device_property_count_u32(dev, "snps,incr-burst-type-adjustment");
964 vals = kcalloc(ntype, sizeof(u32), GFP_KERNEL);
968 /* Get INCR burst type, and parse it */
969 ret = device_property_read_u32_array(dev,
970 "snps,incr-burst-type-adjustment", vals, ntype);
973 dev_err(dev, "Error to get property\n");
980 /* INCRX (undefined length) burst mode */
981 incrx_mode = INCRX_UNDEF_LENGTH_BURST_MODE;
982 for (i = 1; i < ntype; i++) {
983 if (vals[i] > incrx_size)
984 incrx_size = vals[i];
987 /* INCRX burst mode */
988 incrx_mode = INCRX_BURST_MODE;
993 /* Enable Undefined Length INCR Burst and Enable INCRx Burst */
994 cfg &= ~DWC3_GSBUSCFG0_INCRBRST_MASK;
996 cfg |= DWC3_GSBUSCFG0_INCRBRSTENA;
997 switch (incrx_size) {
999 cfg |= DWC3_GSBUSCFG0_INCR256BRSTENA;
1002 cfg |= DWC3_GSBUSCFG0_INCR128BRSTENA;
1005 cfg |= DWC3_GSBUSCFG0_INCR64BRSTENA;
1008 cfg |= DWC3_GSBUSCFG0_INCR32BRSTENA;
1011 cfg |= DWC3_GSBUSCFG0_INCR16BRSTENA;
1014 cfg |= DWC3_GSBUSCFG0_INCR8BRSTENA;
1017 cfg |= DWC3_GSBUSCFG0_INCR4BRSTENA;
1022 dev_err(dev, "Invalid property\n");
1026 dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, cfg);
1029 static void dwc3_set_power_down_clk_scale(struct dwc3 *dwc)
1038 * The power down scale field specifies how many suspend_clk
1039 * periods fit into a 16KHz clock period. When performing
1040 * the division, round up the remainder.
1042 * The power down scale value is calculated using the fastest
1043 * frequency of the suspend_clk. If it isn't fixed (but within
1044 * the accuracy requirement), the driver may not know the max
1045 * rate of the suspend_clk, so only update the power down scale
1046 * if the default is less than the calculated value from
1047 * clk_get_rate() or if the default is questionably high
1048 * (3x or more) to be within the requirement.
1050 scale = DIV_ROUND_UP(clk_get_rate(dwc->susp_clk), 16000);
1051 reg = dwc3_readl(dwc->regs, DWC3_GCTL);
1052 if ((reg & DWC3_GCTL_PWRDNSCALE_MASK) < DWC3_GCTL_PWRDNSCALE(scale) ||
1053 (reg & DWC3_GCTL_PWRDNSCALE_MASK) > DWC3_GCTL_PWRDNSCALE(scale*3)) {
1054 reg &= ~(DWC3_GCTL_PWRDNSCALE_MASK);
1055 reg |= DWC3_GCTL_PWRDNSCALE(scale);
1056 dwc3_writel(dwc->regs, DWC3_GCTL, reg);
1061 * dwc3_core_init - Low-level initialization of DWC3 Core
1062 * @dwc: Pointer to our controller context structure
1064 * Returns 0 on success otherwise negative errno.
1066 static int dwc3_core_init(struct dwc3 *dwc)
1068 unsigned int hw_mode;
1072 hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0);
1075 * Write Linux Version Code to our GUID register so it's easy to figure
1076 * out which kernel version a bug was found.
1078 dwc3_writel(dwc->regs, DWC3_GUID, LINUX_VERSION_CODE);
1080 ret = dwc3_phy_setup(dwc);
1084 if (!dwc->ulpi_ready) {
1085 ret = dwc3_core_ulpi_init(dwc);
1087 if (ret == -ETIMEDOUT) {
1088 dwc3_core_soft_reset(dwc);
1089 ret = -EPROBE_DEFER;
1093 dwc->ulpi_ready = true;
1096 if (!dwc->phys_ready) {
1097 ret = dwc3_core_get_phy(dwc);
1100 dwc->phys_ready = true;
1103 ret = dwc3_phy_init(dwc);
1107 ret = dwc3_core_soft_reset(dwc);
1111 if (hw_mode == DWC3_GHWPARAMS0_MODE_DRD &&
1112 !DWC3_VER_IS_WITHIN(DWC3, ANY, 194A)) {
1113 if (!dwc->dis_u3_susphy_quirk) {
1114 reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
1115 reg |= DWC3_GUSB3PIPECTL_SUSPHY;
1116 dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
1119 if (!dwc->dis_u2_susphy_quirk) {
1120 reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
1121 reg |= DWC3_GUSB2PHYCFG_SUSPHY;
1122 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
1126 dwc3_core_setup_global_control(dwc);
1127 dwc3_core_num_eps(dwc);
1129 /* Set power down scale of suspend_clk */
1130 dwc3_set_power_down_clk_scale(dwc);
1132 /* Adjust Frame Length */
1133 dwc3_frame_length_adjustment(dwc);
1135 /* Adjust Reference Clock Period */
1136 dwc3_ref_clk_period(dwc);
1138 dwc3_set_incr_burst_type(dwc);
1140 ret = dwc3_phy_power_on(dwc);
1144 ret = dwc3_event_buffers_setup(dwc);
1146 dev_err(dwc->dev, "failed to setup event buffers\n");
1147 goto err_power_off_phy;
1151 * ENDXFER polling is available on version 3.10a and later of
1152 * the DWC_usb3 controller. It is NOT available in the
1153 * DWC_usb31 controller.
1155 if (DWC3_VER_IS_WITHIN(DWC3, 310A, ANY)) {
1156 reg = dwc3_readl(dwc->regs, DWC3_GUCTL2);
1157 reg |= DWC3_GUCTL2_RST_ACTBITLATER;
1158 dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
1162 * When configured in HOST mode, after issuing U3/L2 exit controller
1163 * fails to send proper CRC checksum in CRC5 feild. Because of this
1164 * behaviour Transaction Error is generated, resulting in reset and
1165 * re-enumeration of usb device attached. All the termsel, xcvrsel,
1166 * opmode becomes 0 during end of resume. Enabling bit 10 of GUCTL1
1167 * will correct this problem. This option is to support certain
1170 if (dwc->resume_hs_terminations) {
1171 reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
1172 reg |= DWC3_GUCTL1_RESUME_OPMODE_HS_HOST;
1173 dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
1176 if (!DWC3_VER_IS_PRIOR(DWC3, 250A)) {
1177 reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
1180 * Enable hardware control of sending remote wakeup
1181 * in HS when the device is in the L1 state.
1183 if (!DWC3_VER_IS_PRIOR(DWC3, 290A))
1184 reg |= DWC3_GUCTL1_DEV_L1_EXIT_BY_HW;
1187 * Decouple USB 2.0 L1 & L2 events which will allow for
1188 * gadget driver to only receive U3/L2 suspend & wakeup
1189 * events and prevent the more frequent L1 LPM transitions
1190 * from interrupting the driver.
1192 if (!DWC3_VER_IS_PRIOR(DWC3, 300A))
1193 reg |= DWC3_GUCTL1_DEV_DECOUPLE_L1L2_EVT;
1195 if (dwc->dis_tx_ipgap_linecheck_quirk)
1196 reg |= DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS;
1198 if (dwc->parkmode_disable_ss_quirk)
1199 reg |= DWC3_GUCTL1_PARKMODE_DISABLE_SS;
1201 if (dwc->parkmode_disable_hs_quirk)
1202 reg |= DWC3_GUCTL1_PARKMODE_DISABLE_HS;
1204 if (DWC3_VER_IS_WITHIN(DWC3, 290A, ANY) &&
1205 (dwc->maximum_speed == USB_SPEED_HIGH ||
1206 dwc->maximum_speed == USB_SPEED_FULL))
1207 reg |= DWC3_GUCTL1_DEV_FORCE_20_CLK_FOR_30_CLK;
1209 dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
1213 * Must config both number of packets and max burst settings to enable
1214 * RX and/or TX threshold.
1216 if (!DWC3_IP_IS(DWC3) && dwc->dr_mode == USB_DR_MODE_HOST) {
1217 u8 rx_thr_num = dwc->rx_thr_num_pkt_prd;
1218 u8 rx_maxburst = dwc->rx_max_burst_prd;
1219 u8 tx_thr_num = dwc->tx_thr_num_pkt_prd;
1220 u8 tx_maxburst = dwc->tx_max_burst_prd;
1222 if (rx_thr_num && rx_maxburst) {
1223 reg = dwc3_readl(dwc->regs, DWC3_GRXTHRCFG);
1224 reg |= DWC31_RXTHRNUMPKTSEL_PRD;
1226 reg &= ~DWC31_RXTHRNUMPKT_PRD(~0);
1227 reg |= DWC31_RXTHRNUMPKT_PRD(rx_thr_num);
1229 reg &= ~DWC31_MAXRXBURSTSIZE_PRD(~0);
1230 reg |= DWC31_MAXRXBURSTSIZE_PRD(rx_maxburst);
1232 dwc3_writel(dwc->regs, DWC3_GRXTHRCFG, reg);
1235 if (tx_thr_num && tx_maxburst) {
1236 reg = dwc3_readl(dwc->regs, DWC3_GTXTHRCFG);
1237 reg |= DWC31_TXTHRNUMPKTSEL_PRD;
1239 reg &= ~DWC31_TXTHRNUMPKT_PRD(~0);
1240 reg |= DWC31_TXTHRNUMPKT_PRD(tx_thr_num);
1242 reg &= ~DWC31_MAXTXBURSTSIZE_PRD(~0);
1243 reg |= DWC31_MAXTXBURSTSIZE_PRD(tx_maxburst);
1245 dwc3_writel(dwc->regs, DWC3_GTXTHRCFG, reg);
1252 dwc3_phy_power_off(dwc);
1256 dwc3_ulpi_exit(dwc);
1261 static int dwc3_core_get_phy(struct dwc3 *dwc)
1263 struct device *dev = dwc->dev;
1264 struct device_node *node = dev->of_node;
1268 dwc->usb2_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 0);
1269 dwc->usb3_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 1);
1271 dwc->usb2_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
1272 dwc->usb3_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB3);
1275 if (IS_ERR(dwc->usb2_phy)) {
1276 ret = PTR_ERR(dwc->usb2_phy);
1277 if (ret == -ENXIO || ret == -ENODEV)
1278 dwc->usb2_phy = NULL;
1280 return dev_err_probe(dev, ret, "no usb2 phy configured\n");
1283 if (IS_ERR(dwc->usb3_phy)) {
1284 ret = PTR_ERR(dwc->usb3_phy);
1285 if (ret == -ENXIO || ret == -ENODEV)
1286 dwc->usb3_phy = NULL;
1288 return dev_err_probe(dev, ret, "no usb3 phy configured\n");
1291 dwc->usb2_generic_phy = devm_phy_get(dev, "usb2-phy");
1292 if (IS_ERR(dwc->usb2_generic_phy)) {
1293 ret = PTR_ERR(dwc->usb2_generic_phy);
1294 if (ret == -ENOSYS || ret == -ENODEV)
1295 dwc->usb2_generic_phy = NULL;
1297 return dev_err_probe(dev, ret, "no usb2 phy configured\n");
1300 dwc->usb3_generic_phy = devm_phy_get(dev, "usb3-phy");
1301 if (IS_ERR(dwc->usb3_generic_phy)) {
1302 ret = PTR_ERR(dwc->usb3_generic_phy);
1303 if (ret == -ENOSYS || ret == -ENODEV)
1304 dwc->usb3_generic_phy = NULL;
1306 return dev_err_probe(dev, ret, "no usb3 phy configured\n");
1312 static int dwc3_core_init_mode(struct dwc3 *dwc)
1314 struct device *dev = dwc->dev;
1317 switch (dwc->dr_mode) {
1318 case USB_DR_MODE_PERIPHERAL:
1319 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
1322 otg_set_vbus(dwc->usb2_phy->otg, false);
1323 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_DEVICE);
1324 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_DEVICE);
1326 ret = dwc3_gadget_init(dwc);
1328 return dev_err_probe(dev, ret, "failed to initialize gadget\n");
1330 case USB_DR_MODE_HOST:
1331 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
1334 otg_set_vbus(dwc->usb2_phy->otg, true);
1335 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST);
1336 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_HOST);
1338 ret = dwc3_host_init(dwc);
1340 return dev_err_probe(dev, ret, "failed to initialize host\n");
1342 case USB_DR_MODE_OTG:
1343 INIT_WORK(&dwc->drd_work, __dwc3_set_mode);
1344 ret = dwc3_drd_init(dwc);
1346 return dev_err_probe(dev, ret, "failed to initialize dual-role\n");
1349 dev_err(dev, "Unsupported mode of operation %d\n", dwc->dr_mode);
1356 static void dwc3_core_exit_mode(struct dwc3 *dwc)
1358 switch (dwc->dr_mode) {
1359 case USB_DR_MODE_PERIPHERAL:
1360 dwc3_gadget_exit(dwc);
1362 case USB_DR_MODE_HOST:
1363 dwc3_host_exit(dwc);
1365 case USB_DR_MODE_OTG:
1373 /* de-assert DRVVBUS for HOST and OTG mode */
1374 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
1377 static void dwc3_get_properties(struct dwc3 *dwc)
1379 struct device *dev = dwc->dev;
1380 u8 lpm_nyet_threshold;
1383 u8 rx_thr_num_pkt_prd = 0;
1384 u8 rx_max_burst_prd = 0;
1385 u8 tx_thr_num_pkt_prd = 0;
1386 u8 tx_max_burst_prd = 0;
1387 u8 tx_fifo_resize_max_num;
1388 const char *usb_psy_name;
1391 /* default to highest possible threshold */
1392 lpm_nyet_threshold = 0xf;
1394 /* default to -3.5dB de-emphasis */
1398 * default to assert utmi_sleep_n and use maximum allowed HIRD
1399 * threshold value of 0b1100
1401 hird_threshold = 12;
1404 * default to a TXFIFO size large enough to fit 6 max packets. This
1405 * allows for systems with larger bus latencies to have some headroom
1406 * for endpoints that have a large bMaxBurst value.
1408 tx_fifo_resize_max_num = 6;
1410 dwc->maximum_speed = usb_get_maximum_speed(dev);
1411 dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
1412 dwc->dr_mode = usb_get_dr_mode(dev);
1413 dwc->hsphy_mode = of_usb_get_phy_mode(dev->of_node);
1415 dwc->sysdev_is_parent = device_property_read_bool(dev,
1416 "linux,sysdev_is_parent");
1417 if (dwc->sysdev_is_parent)
1418 dwc->sysdev = dwc->dev->parent;
1420 dwc->sysdev = dwc->dev;
1422 ret = device_property_read_string(dev, "usb-psy-name", &usb_psy_name);
1424 dwc->usb_psy = power_supply_get_by_name(usb_psy_name);
1426 dev_err(dev, "couldn't get usb power supply\n");
1429 dwc->has_lpm_erratum = device_property_read_bool(dev,
1430 "snps,has-lpm-erratum");
1431 device_property_read_u8(dev, "snps,lpm-nyet-threshold",
1432 &lpm_nyet_threshold);
1433 dwc->is_utmi_l1_suspend = device_property_read_bool(dev,
1434 "snps,is-utmi-l1-suspend");
1435 device_property_read_u8(dev, "snps,hird-threshold",
1437 dwc->dis_start_transfer_quirk = device_property_read_bool(dev,
1438 "snps,dis-start-transfer-quirk");
1439 dwc->usb3_lpm_capable = device_property_read_bool(dev,
1440 "snps,usb3_lpm_capable");
1441 dwc->usb2_lpm_disable = device_property_read_bool(dev,
1442 "snps,usb2-lpm-disable");
1443 dwc->usb2_gadget_lpm_disable = device_property_read_bool(dev,
1444 "snps,usb2-gadget-lpm-disable");
1445 device_property_read_u8(dev, "snps,rx-thr-num-pkt-prd",
1446 &rx_thr_num_pkt_prd);
1447 device_property_read_u8(dev, "snps,rx-max-burst-prd",
1449 device_property_read_u8(dev, "snps,tx-thr-num-pkt-prd",
1450 &tx_thr_num_pkt_prd);
1451 device_property_read_u8(dev, "snps,tx-max-burst-prd",
1453 dwc->do_fifo_resize = device_property_read_bool(dev,
1455 if (dwc->do_fifo_resize)
1456 device_property_read_u8(dev, "tx-fifo-max-num",
1457 &tx_fifo_resize_max_num);
1459 dwc->disable_scramble_quirk = device_property_read_bool(dev,
1460 "snps,disable_scramble_quirk");
1461 dwc->u2exit_lfps_quirk = device_property_read_bool(dev,
1462 "snps,u2exit_lfps_quirk");
1463 dwc->u2ss_inp3_quirk = device_property_read_bool(dev,
1464 "snps,u2ss_inp3_quirk");
1465 dwc->req_p1p2p3_quirk = device_property_read_bool(dev,
1466 "snps,req_p1p2p3_quirk");
1467 dwc->del_p1p2p3_quirk = device_property_read_bool(dev,
1468 "snps,del_p1p2p3_quirk");
1469 dwc->del_phy_power_chg_quirk = device_property_read_bool(dev,
1470 "snps,del_phy_power_chg_quirk");
1471 dwc->lfps_filter_quirk = device_property_read_bool(dev,
1472 "snps,lfps_filter_quirk");
1473 dwc->rx_detect_poll_quirk = device_property_read_bool(dev,
1474 "snps,rx_detect_poll_quirk");
1475 dwc->dis_u3_susphy_quirk = device_property_read_bool(dev,
1476 "snps,dis_u3_susphy_quirk");
1477 dwc->dis_u2_susphy_quirk = device_property_read_bool(dev,
1478 "snps,dis_u2_susphy_quirk");
1479 dwc->dis_enblslpm_quirk = device_property_read_bool(dev,
1480 "snps,dis_enblslpm_quirk");
1481 dwc->dis_u1_entry_quirk = device_property_read_bool(dev,
1482 "snps,dis-u1-entry-quirk");
1483 dwc->dis_u2_entry_quirk = device_property_read_bool(dev,
1484 "snps,dis-u2-entry-quirk");
1485 dwc->dis_rxdet_inp3_quirk = device_property_read_bool(dev,
1486 "snps,dis_rxdet_inp3_quirk");
1487 dwc->dis_u2_freeclk_exists_quirk = device_property_read_bool(dev,
1488 "snps,dis-u2-freeclk-exists-quirk");
1489 dwc->dis_del_phy_power_chg_quirk = device_property_read_bool(dev,
1490 "snps,dis-del-phy-power-chg-quirk");
1491 dwc->dis_tx_ipgap_linecheck_quirk = device_property_read_bool(dev,
1492 "snps,dis-tx-ipgap-linecheck-quirk");
1493 dwc->resume_hs_terminations = device_property_read_bool(dev,
1494 "snps,resume-hs-terminations");
1495 dwc->ulpi_ext_vbus_drv = device_property_read_bool(dev,
1496 "snps,ulpi-ext-vbus-drv");
1497 dwc->parkmode_disable_ss_quirk = device_property_read_bool(dev,
1498 "snps,parkmode-disable-ss-quirk");
1499 dwc->parkmode_disable_hs_quirk = device_property_read_bool(dev,
1500 "snps,parkmode-disable-hs-quirk");
1501 dwc->gfladj_refclk_lpm_sel = device_property_read_bool(dev,
1502 "snps,gfladj-refclk-lpm-sel-quirk");
1504 dwc->tx_de_emphasis_quirk = device_property_read_bool(dev,
1505 "snps,tx_de_emphasis_quirk");
1506 device_property_read_u8(dev, "snps,tx_de_emphasis",
1508 device_property_read_string(dev, "snps,hsphy_interface",
1509 &dwc->hsphy_interface);
1510 device_property_read_u32(dev, "snps,quirk-frame-length-adjustment",
1512 device_property_read_u32(dev, "snps,ref-clock-period-ns",
1515 dwc->dis_metastability_quirk = device_property_read_bool(dev,
1516 "snps,dis_metastability_quirk");
1518 dwc->dis_split_quirk = device_property_read_bool(dev,
1519 "snps,dis-split-quirk");
1521 dwc->lpm_nyet_threshold = lpm_nyet_threshold;
1522 dwc->tx_de_emphasis = tx_de_emphasis;
1524 dwc->hird_threshold = hird_threshold;
1526 dwc->rx_thr_num_pkt_prd = rx_thr_num_pkt_prd;
1527 dwc->rx_max_burst_prd = rx_max_burst_prd;
1529 dwc->tx_thr_num_pkt_prd = tx_thr_num_pkt_prd;
1530 dwc->tx_max_burst_prd = tx_max_burst_prd;
1532 dwc->imod_interval = 0;
1534 dwc->tx_fifo_resize_max_num = tx_fifo_resize_max_num;
1537 /* check whether the core supports IMOD */
1538 bool dwc3_has_imod(struct dwc3 *dwc)
1540 return DWC3_VER_IS_WITHIN(DWC3, 300A, ANY) ||
1541 DWC3_VER_IS_WITHIN(DWC31, 120A, ANY) ||
1545 static void dwc3_check_params(struct dwc3 *dwc)
1547 struct device *dev = dwc->dev;
1548 unsigned int hwparam_gen =
1549 DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3);
1551 /* Check for proper value of imod_interval */
1552 if (dwc->imod_interval && !dwc3_has_imod(dwc)) {
1553 dev_warn(dwc->dev, "Interrupt moderation not supported\n");
1554 dwc->imod_interval = 0;
1558 * Workaround for STAR 9000961433 which affects only version
1559 * 3.00a of the DWC_usb3 core. This prevents the controller
1560 * interrupt from being masked while handling events. IMOD
1561 * allows us to work around this issue. Enable it for the
1564 if (!dwc->imod_interval &&
1565 DWC3_VER_IS(DWC3, 300A))
1566 dwc->imod_interval = 1;
1568 /* Check the maximum_speed parameter */
1569 switch (dwc->maximum_speed) {
1570 case USB_SPEED_FULL:
1571 case USB_SPEED_HIGH:
1573 case USB_SPEED_SUPER:
1574 if (hwparam_gen == DWC3_GHWPARAMS3_SSPHY_IFC_DIS)
1575 dev_warn(dev, "UDC doesn't support Gen 1\n");
1577 case USB_SPEED_SUPER_PLUS:
1578 if ((DWC3_IP_IS(DWC32) &&
1579 hwparam_gen == DWC3_GHWPARAMS3_SSPHY_IFC_DIS) ||
1580 (!DWC3_IP_IS(DWC32) &&
1581 hwparam_gen != DWC3_GHWPARAMS3_SSPHY_IFC_GEN2))
1582 dev_warn(dev, "UDC doesn't support SSP\n");
1585 dev_err(dev, "invalid maximum_speed parameter %d\n",
1586 dwc->maximum_speed);
1588 case USB_SPEED_UNKNOWN:
1589 switch (hwparam_gen) {
1590 case DWC3_GHWPARAMS3_SSPHY_IFC_GEN2:
1591 dwc->maximum_speed = USB_SPEED_SUPER_PLUS;
1593 case DWC3_GHWPARAMS3_SSPHY_IFC_GEN1:
1594 if (DWC3_IP_IS(DWC32))
1595 dwc->maximum_speed = USB_SPEED_SUPER_PLUS;
1597 dwc->maximum_speed = USB_SPEED_SUPER;
1599 case DWC3_GHWPARAMS3_SSPHY_IFC_DIS:
1600 dwc->maximum_speed = USB_SPEED_HIGH;
1603 dwc->maximum_speed = USB_SPEED_SUPER;
1610 * Currently the controller does not have visibility into the HW
1611 * parameter to determine the maximum number of lanes the HW supports.
1612 * If the number of lanes is not specified in the device property, then
1613 * set the default to support dual-lane for DWC_usb32 and single-lane
1614 * for DWC_usb31 for super-speed-plus.
1616 if (dwc->maximum_speed == USB_SPEED_SUPER_PLUS) {
1617 switch (dwc->max_ssp_rate) {
1618 case USB_SSP_GEN_2x1:
1619 if (hwparam_gen == DWC3_GHWPARAMS3_SSPHY_IFC_GEN1)
1620 dev_warn(dev, "UDC only supports Gen 1\n");
1622 case USB_SSP_GEN_1x2:
1623 case USB_SSP_GEN_2x2:
1624 if (DWC3_IP_IS(DWC31))
1625 dev_warn(dev, "UDC only supports single lane\n");
1627 case USB_SSP_GEN_UNKNOWN:
1629 switch (hwparam_gen) {
1630 case DWC3_GHWPARAMS3_SSPHY_IFC_GEN2:
1631 if (DWC3_IP_IS(DWC32))
1632 dwc->max_ssp_rate = USB_SSP_GEN_2x2;
1634 dwc->max_ssp_rate = USB_SSP_GEN_2x1;
1636 case DWC3_GHWPARAMS3_SSPHY_IFC_GEN1:
1637 if (DWC3_IP_IS(DWC32))
1638 dwc->max_ssp_rate = USB_SSP_GEN_1x2;
1646 static struct extcon_dev *dwc3_get_extcon(struct dwc3 *dwc)
1648 struct device *dev = dwc->dev;
1649 struct device_node *np_phy;
1650 struct extcon_dev *edev = NULL;
1653 if (device_property_read_bool(dev, "extcon"))
1654 return extcon_get_edev_by_phandle(dev, 0);
1657 * Device tree platforms should get extcon via phandle.
1658 * On ACPI platforms, we get the name from a device property.
1659 * This device property is for kernel internal use only and
1660 * is expected to be set by the glue code.
1662 if (device_property_read_string(dev, "linux,extcon-name", &name) == 0)
1663 return extcon_get_extcon_dev(name);
1666 * Check explicitly if "usb-role-switch" is used since
1667 * extcon_find_edev_by_node() can not be used to check the absence of
1668 * an extcon device. In the absence of an device it will always return
1671 if (IS_ENABLED(CONFIG_USB_ROLE_SWITCH) &&
1672 device_property_read_bool(dev, "usb-role-switch"))
1676 * Try to get an extcon device from the USB PHY controller's "port"
1677 * node. Check if it has the "port" node first, to avoid printing the
1678 * error message from underlying code, as it's a valid case: extcon
1679 * device (and "port" node) may be missing in case of "usb-role-switch"
1682 np_phy = of_parse_phandle(dev->of_node, "phys", 0);
1683 if (of_graph_is_present(np_phy)) {
1684 struct device_node *np_conn;
1686 np_conn = of_graph_get_remote_node(np_phy, -1, -1);
1688 edev = extcon_find_edev_by_node(np_conn);
1689 of_node_put(np_conn);
1691 of_node_put(np_phy);
1696 static int dwc3_get_clocks(struct dwc3 *dwc)
1698 struct device *dev = dwc->dev;
1704 * Clocks are optional, but new DT platforms should support all clocks
1705 * as required by the DT-binding.
1706 * Some devices have different clock names in legacy device trees,
1707 * check for them to retain backwards compatibility.
1709 dwc->bus_clk = devm_clk_get_optional(dev, "bus_early");
1710 if (IS_ERR(dwc->bus_clk)) {
1711 return dev_err_probe(dev, PTR_ERR(dwc->bus_clk),
1712 "could not get bus clock\n");
1715 if (dwc->bus_clk == NULL) {
1716 dwc->bus_clk = devm_clk_get_optional(dev, "bus_clk");
1717 if (IS_ERR(dwc->bus_clk)) {
1718 return dev_err_probe(dev, PTR_ERR(dwc->bus_clk),
1719 "could not get bus clock\n");
1723 dwc->ref_clk = devm_clk_get_optional(dev, "ref");
1724 if (IS_ERR(dwc->ref_clk)) {
1725 return dev_err_probe(dev, PTR_ERR(dwc->ref_clk),
1726 "could not get ref clock\n");
1729 if (dwc->ref_clk == NULL) {
1730 dwc->ref_clk = devm_clk_get_optional(dev, "ref_clk");
1731 if (IS_ERR(dwc->ref_clk)) {
1732 return dev_err_probe(dev, PTR_ERR(dwc->ref_clk),
1733 "could not get ref clock\n");
1737 dwc->susp_clk = devm_clk_get_optional(dev, "suspend");
1738 if (IS_ERR(dwc->susp_clk)) {
1739 return dev_err_probe(dev, PTR_ERR(dwc->susp_clk),
1740 "could not get suspend clock\n");
1743 if (dwc->susp_clk == NULL) {
1744 dwc->susp_clk = devm_clk_get_optional(dev, "suspend_clk");
1745 if (IS_ERR(dwc->susp_clk)) {
1746 return dev_err_probe(dev, PTR_ERR(dwc->susp_clk),
1747 "could not get suspend clock\n");
1754 static int dwc3_probe(struct platform_device *pdev)
1756 struct device *dev = &pdev->dev;
1757 struct resource *res, dwc_res;
1762 dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL);
1768 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1770 dev_err(dev, "missing memory resource\n");
1774 dwc->xhci_resources[0].start = res->start;
1775 dwc->xhci_resources[0].end = dwc->xhci_resources[0].start +
1777 dwc->xhci_resources[0].flags = res->flags;
1778 dwc->xhci_resources[0].name = res->name;
1781 * Request memory region but exclude xHCI regs,
1782 * since it will be requested by the xhci-plat driver.
1785 dwc_res.start += DWC3_GLOBALS_REGS_START;
1788 struct device_node *parent = of_get_parent(dev->of_node);
1790 if (of_device_is_compatible(parent, "realtek,rtd-dwc3")) {
1791 dwc_res.start -= DWC3_GLOBALS_REGS_START;
1792 dwc_res.start += DWC3_RTK_RTD_GLOBALS_REGS_START;
1795 of_node_put(parent);
1798 regs = devm_ioremap_resource(dev, &dwc_res);
1800 return PTR_ERR(regs);
1803 dwc->regs_size = resource_size(&dwc_res);
1805 dwc3_get_properties(dwc);
1807 dwc->reset = devm_reset_control_array_get_optional_shared(dev);
1808 if (IS_ERR(dwc->reset)) {
1809 ret = PTR_ERR(dwc->reset);
1813 ret = dwc3_get_clocks(dwc);
1817 ret = reset_control_deassert(dwc->reset);
1821 ret = dwc3_clk_enable(dwc);
1823 goto err_assert_reset;
1825 if (!dwc3_core_is_valid(dwc)) {
1826 dev_err(dwc->dev, "this is not a DesignWare USB3 DRD Core\n");
1828 goto err_disable_clks;
1831 platform_set_drvdata(pdev, dwc);
1832 dwc3_cache_hwparams(dwc);
1834 if (!dwc->sysdev_is_parent &&
1835 DWC3_GHWPARAMS0_AWIDTH(dwc->hwparams.hwparams0) == 64) {
1836 ret = dma_set_mask_and_coherent(dwc->sysdev, DMA_BIT_MASK(64));
1838 goto err_disable_clks;
1841 spin_lock_init(&dwc->lock);
1842 mutex_init(&dwc->mutex);
1844 pm_runtime_get_noresume(dev);
1845 pm_runtime_set_active(dev);
1846 pm_runtime_use_autosuspend(dev);
1847 pm_runtime_set_autosuspend_delay(dev, DWC3_DEFAULT_AUTOSUSPEND_DELAY);
1848 pm_runtime_enable(dev);
1850 pm_runtime_forbid(dev);
1852 ret = dwc3_alloc_event_buffers(dwc, DWC3_EVENT_BUFFERS_SIZE);
1854 dev_err(dwc->dev, "failed to allocate event buffers\n");
1859 dwc->edev = dwc3_get_extcon(dwc);
1860 if (IS_ERR(dwc->edev)) {
1861 ret = dev_err_probe(dwc->dev, PTR_ERR(dwc->edev), "failed to get extcon\n");
1862 goto err_free_event_buffers;
1865 ret = dwc3_get_dr_mode(dwc);
1867 goto err_free_event_buffers;
1869 ret = dwc3_core_init(dwc);
1871 dev_err_probe(dev, ret, "failed to initialize core\n");
1872 goto err_free_event_buffers;
1875 dwc3_check_params(dwc);
1876 dwc3_debugfs_init(dwc);
1878 ret = dwc3_core_init_mode(dwc);
1880 goto err_exit_debugfs;
1882 pm_runtime_put(dev);
1887 dwc3_debugfs_exit(dwc);
1888 dwc3_event_buffers_cleanup(dwc);
1889 dwc3_phy_power_off(dwc);
1891 dwc3_ulpi_exit(dwc);
1892 err_free_event_buffers:
1893 dwc3_free_event_buffers(dwc);
1895 pm_runtime_allow(dev);
1896 pm_runtime_disable(dev);
1897 pm_runtime_dont_use_autosuspend(dev);
1898 pm_runtime_set_suspended(dev);
1899 pm_runtime_put_noidle(dev);
1901 dwc3_clk_disable(dwc);
1903 reset_control_assert(dwc->reset);
1906 power_supply_put(dwc->usb_psy);
1911 static void dwc3_remove(struct platform_device *pdev)
1913 struct dwc3 *dwc = platform_get_drvdata(pdev);
1915 pm_runtime_get_sync(&pdev->dev);
1917 dwc3_core_exit_mode(dwc);
1918 dwc3_debugfs_exit(dwc);
1920 dwc3_core_exit(dwc);
1921 dwc3_ulpi_exit(dwc);
1923 pm_runtime_allow(&pdev->dev);
1924 pm_runtime_disable(&pdev->dev);
1925 pm_runtime_dont_use_autosuspend(&pdev->dev);
1926 pm_runtime_put_noidle(&pdev->dev);
1928 * HACK: Clear the driver data, which is currently accessed by parent
1929 * glue drivers, before allowing the parent to suspend.
1931 platform_set_drvdata(pdev, NULL);
1932 pm_runtime_set_suspended(&pdev->dev);
1934 dwc3_free_event_buffers(dwc);
1937 power_supply_put(dwc->usb_psy);
1941 static int dwc3_core_init_for_resume(struct dwc3 *dwc)
1945 ret = reset_control_deassert(dwc->reset);
1949 ret = dwc3_clk_enable(dwc);
1953 ret = dwc3_core_init(dwc);
1960 dwc3_clk_disable(dwc);
1962 reset_control_assert(dwc->reset);
1967 static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
1969 unsigned long flags;
1972 switch (dwc->current_dr_role) {
1973 case DWC3_GCTL_PRTCAP_DEVICE:
1974 if (pm_runtime_suspended(dwc->dev))
1976 dwc3_gadget_suspend(dwc);
1977 synchronize_irq(dwc->irq_gadget);
1978 dwc3_core_exit(dwc);
1980 case DWC3_GCTL_PRTCAP_HOST:
1981 if (!PMSG_IS_AUTO(msg) && !device_may_wakeup(dwc->dev)) {
1982 dwc3_core_exit(dwc);
1986 /* Let controller to suspend HSPHY before PHY driver suspends */
1987 if (dwc->dis_u2_susphy_quirk ||
1988 dwc->dis_enblslpm_quirk) {
1989 reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
1990 reg |= DWC3_GUSB2PHYCFG_ENBLSLPM |
1991 DWC3_GUSB2PHYCFG_SUSPHY;
1992 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
1994 /* Give some time for USB2 PHY to suspend */
1995 usleep_range(5000, 6000);
1998 phy_pm_runtime_put_sync(dwc->usb2_generic_phy);
1999 phy_pm_runtime_put_sync(dwc->usb3_generic_phy);
2001 case DWC3_GCTL_PRTCAP_OTG:
2002 /* do nothing during runtime_suspend */
2003 if (PMSG_IS_AUTO(msg))
2006 if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) {
2007 spin_lock_irqsave(&dwc->lock, flags);
2008 dwc3_gadget_suspend(dwc);
2009 spin_unlock_irqrestore(&dwc->lock, flags);
2010 synchronize_irq(dwc->irq_gadget);
2014 dwc3_core_exit(dwc);
2024 static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg)
2026 unsigned long flags;
2030 switch (dwc->current_dr_role) {
2031 case DWC3_GCTL_PRTCAP_DEVICE:
2032 ret = dwc3_core_init_for_resume(dwc);
2036 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
2037 dwc3_gadget_resume(dwc);
2039 case DWC3_GCTL_PRTCAP_HOST:
2040 if (!PMSG_IS_AUTO(msg) && !device_may_wakeup(dwc->dev)) {
2041 ret = dwc3_core_init_for_resume(dwc);
2044 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
2047 /* Restore GUSB2PHYCFG bits that were modified in suspend */
2048 reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
2049 if (dwc->dis_u2_susphy_quirk)
2050 reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
2052 if (dwc->dis_enblslpm_quirk)
2053 reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
2055 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
2057 phy_pm_runtime_get_sync(dwc->usb2_generic_phy);
2058 phy_pm_runtime_get_sync(dwc->usb3_generic_phy);
2060 case DWC3_GCTL_PRTCAP_OTG:
2061 /* nothing to do on runtime_resume */
2062 if (PMSG_IS_AUTO(msg))
2065 ret = dwc3_core_init_for_resume(dwc);
2069 dwc3_set_prtcap(dwc, dwc->current_dr_role);
2072 if (dwc->current_otg_role == DWC3_OTG_ROLE_HOST) {
2073 dwc3_otg_host_init(dwc);
2074 } else if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) {
2075 spin_lock_irqsave(&dwc->lock, flags);
2076 dwc3_gadget_resume(dwc);
2077 spin_unlock_irqrestore(&dwc->lock, flags);
2089 static int dwc3_runtime_checks(struct dwc3 *dwc)
2091 switch (dwc->current_dr_role) {
2092 case DWC3_GCTL_PRTCAP_DEVICE:
2096 case DWC3_GCTL_PRTCAP_HOST:
2105 static int dwc3_runtime_suspend(struct device *dev)
2107 struct dwc3 *dwc = dev_get_drvdata(dev);
2110 if (dwc3_runtime_checks(dwc))
2113 ret = dwc3_suspend_common(dwc, PMSG_AUTO_SUSPEND);
2120 static int dwc3_runtime_resume(struct device *dev)
2122 struct dwc3 *dwc = dev_get_drvdata(dev);
2125 ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME);
2129 switch (dwc->current_dr_role) {
2130 case DWC3_GCTL_PRTCAP_DEVICE:
2131 dwc3_gadget_process_pending_events(dwc);
2133 case DWC3_GCTL_PRTCAP_HOST:
2139 pm_runtime_mark_last_busy(dev);
2144 static int dwc3_runtime_idle(struct device *dev)
2146 struct dwc3 *dwc = dev_get_drvdata(dev);
2148 switch (dwc->current_dr_role) {
2149 case DWC3_GCTL_PRTCAP_DEVICE:
2150 if (dwc3_runtime_checks(dwc))
2153 case DWC3_GCTL_PRTCAP_HOST:
2159 pm_runtime_mark_last_busy(dev);
2160 pm_runtime_autosuspend(dev);
2164 #endif /* CONFIG_PM */
2166 #ifdef CONFIG_PM_SLEEP
2167 static int dwc3_suspend(struct device *dev)
2169 struct dwc3 *dwc = dev_get_drvdata(dev);
2172 ret = dwc3_suspend_common(dwc, PMSG_SUSPEND);
2176 pinctrl_pm_select_sleep_state(dev);
2181 static int dwc3_resume(struct device *dev)
2183 struct dwc3 *dwc = dev_get_drvdata(dev);
2186 pinctrl_pm_select_default_state(dev);
2188 ret = dwc3_resume_common(dwc, PMSG_RESUME);
2192 pm_runtime_disable(dev);
2193 pm_runtime_set_active(dev);
2194 pm_runtime_enable(dev);
2199 static void dwc3_complete(struct device *dev)
2201 struct dwc3 *dwc = dev_get_drvdata(dev);
2204 if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST &&
2205 dwc->dis_split_quirk) {
2206 reg = dwc3_readl(dwc->regs, DWC3_GUCTL3);
2207 reg |= DWC3_GUCTL3_SPLITDISABLE;
2208 dwc3_writel(dwc->regs, DWC3_GUCTL3, reg);
2212 #define dwc3_complete NULL
2213 #endif /* CONFIG_PM_SLEEP */
2215 static const struct dev_pm_ops dwc3_dev_pm_ops = {
2216 SET_SYSTEM_SLEEP_PM_OPS(dwc3_suspend, dwc3_resume)
2217 .complete = dwc3_complete,
2218 SET_RUNTIME_PM_OPS(dwc3_runtime_suspend, dwc3_runtime_resume,
2223 static const struct of_device_id of_dwc3_match[] = {
2225 .compatible = "snps,dwc3"
2228 .compatible = "synopsys,dwc3"
2232 MODULE_DEVICE_TABLE(of, of_dwc3_match);
2237 #define ACPI_ID_INTEL_BSW "808622B7"
2239 static const struct acpi_device_id dwc3_acpi_match[] = {
2240 { ACPI_ID_INTEL_BSW, 0 },
2243 MODULE_DEVICE_TABLE(acpi, dwc3_acpi_match);
2246 static struct platform_driver dwc3_driver = {
2247 .probe = dwc3_probe,
2248 .remove_new = dwc3_remove,
2251 .of_match_table = of_match_ptr(of_dwc3_match),
2252 .acpi_match_table = ACPI_PTR(dwc3_acpi_match),
2253 .pm = &dwc3_dev_pm_ops,
2257 module_platform_driver(dwc3_driver);
2259 MODULE_ALIAS("platform:dwc3");
2260 MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
2261 MODULE_LICENSE("GPL v2");
2262 MODULE_DESCRIPTION("DesignWare USB3 DRD Controller Driver");