1 // SPDX-License-Identifier: GPL-2.0
3 * ARC On-Chip(fpga) UART Driver
5 * Copyright (C) 2010-2012 Synopsys, Inc. (www.synopsys.com)
7 * vineetg: July 10th 2012
8 * -Decoupled the driver from arch/arc
9 * +Using platform_get_resource() for irq/membase (thx to bfin_uart.c)
10 * +Using early_platform_xxx() for early console (thx to mach-shmobile/xxx)
12 * Vineetg: Aug 21st 2010
13 * -Is uart_tx_stopped() not done in tty write path as it has already been
14 * taken care of, in serial core
16 * Vineetg: Aug 18th 2010
17 * -New Serial Core based ARC UART driver
18 * -Derived largely from blackfin driver albiet with some major tweaks
21 * -check if sysreq works
24 #include <linux/module.h>
25 #include <linux/serial.h>
26 #include <linux/console.h>
27 #include <linux/sysrq.h>
28 #include <linux/platform_device.h>
29 #include <linux/tty.h>
30 #include <linux/tty_flip.h>
31 #include <linux/serial_core.h>
33 #include <linux/of_irq.h>
34 #include <linux/of_address.h>
36 /*************************************
37 * ARC UART Hardware Specs
38 ************************************/
39 #define ARC_UART_TX_FIFO_SIZE 1
42 * UART Register set (this is not a Standards Compliant IP)
43 * Also each reg is Word aligned, but only 8 bits wide
54 /* Bits for UART Status Reg (R/W) */
55 #define RXIENB 0x04 /* Receive Interrupt Enable */
56 #define TXIENB 0x40 /* Transmit Interrupt Enable */
58 #define RXEMPTY 0x20 /* Receive FIFO Empty: No char receivede */
59 #define TXEMPTY 0x80 /* Transmit FIFO Empty, thus char can be written into */
61 #define RXFULL 0x08 /* Receive FIFO full */
62 #define RXFULL1 0x10 /* Receive FIFO has space for 1 char (tot space=4) */
64 #define RXFERR 0x01 /* Frame Error: Stop Bit not detected */
65 #define RXOERR 0x02 /* OverFlow Err: Char recv but RXFULL still set */
67 /* Uart bit fiddling helpers: lowest level */
68 #define RBASE(port, reg) (port->membase + reg)
69 #define UART_REG_SET(u, r, v) writeb((v), RBASE(u, r))
70 #define UART_REG_GET(u, r) readb(RBASE(u, r))
72 #define UART_REG_OR(u, r, v) UART_REG_SET(u, r, UART_REG_GET(u, r) | (v))
73 #define UART_REG_CLR(u, r, v) UART_REG_SET(u, r, UART_REG_GET(u, r) & ~(v))
75 /* Uart bit fiddling helpers: API level */
76 #define UART_SET_DATA(uart, val) UART_REG_SET(uart, R_DATA, val)
77 #define UART_GET_DATA(uart) UART_REG_GET(uart, R_DATA)
79 #define UART_SET_BAUDH(uart, val) UART_REG_SET(uart, R_BAUDH, val)
80 #define UART_SET_BAUDL(uart, val) UART_REG_SET(uart, R_BAUDL, val)
82 #define UART_CLR_STATUS(uart, val) UART_REG_CLR(uart, R_STS, val)
83 #define UART_GET_STATUS(uart) UART_REG_GET(uart, R_STS)
85 #define UART_ALL_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, RXIENB|TXIENB)
86 #define UART_RX_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, RXIENB)
87 #define UART_TX_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, TXIENB)
89 #define UART_ALL_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, RXIENB|TXIENB)
90 #define UART_RX_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, RXIENB)
91 #define UART_TX_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, TXIENB)
93 #define ARC_SERIAL_DEV_NAME "ttyARC"
95 struct arc_uart_port {
96 struct uart_port port;
100 #define to_arc_port(uport) container_of(uport, struct arc_uart_port, port)
102 static struct arc_uart_port arc_uart_ports[CONFIG_SERIAL_ARC_NR_PORTS];
104 #ifdef CONFIG_SERIAL_ARC_CONSOLE
105 static struct console arc_console;
108 #define DRIVER_NAME "arc-uart"
110 static struct uart_driver arc_uart_driver = {
111 .owner = THIS_MODULE,
112 .driver_name = DRIVER_NAME,
113 .dev_name = ARC_SERIAL_DEV_NAME,
116 .nr = CONFIG_SERIAL_ARC_NR_PORTS,
117 #ifdef CONFIG_SERIAL_ARC_CONSOLE
118 .cons = &arc_console,
122 static void arc_serial_stop_rx(struct uart_port *port)
124 UART_RX_IRQ_DISABLE(port);
127 static void arc_serial_stop_tx(struct uart_port *port)
129 while (!(UART_GET_STATUS(port) & TXEMPTY))
132 UART_TX_IRQ_DISABLE(port);
136 * Return TIOCSER_TEMT when transmitter is not busy.
138 static unsigned int arc_serial_tx_empty(struct uart_port *port)
142 stat = UART_GET_STATUS(port);
150 * Driver internal routine, used by both tty(serial core) as well as tx-isr
151 * -Called under spinlock in either cases
152 * -also tty->flow.stopped has already been checked
153 * = by uart_start( ) before calling us
154 * = tx_ist checks that too before calling
156 static void arc_serial_tx_chars(struct uart_port *port)
158 struct circ_buf *xmit = &port->state->xmit;
162 if (unlikely(port->x_char)) {
163 UART_SET_DATA(port, port->x_char);
167 } else if (!uart_circ_empty(xmit)) {
168 ch = xmit->buf[xmit->tail];
169 uart_xmit_advance(port, 1);
170 while (!(UART_GET_STATUS(port) & TXEMPTY))
172 UART_SET_DATA(port, ch);
177 * If num chars in xmit buffer are too few, ask tty layer for more.
178 * By Hard ISR to schedule processing in software interrupt part
180 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
181 uart_write_wakeup(port);
184 UART_TX_IRQ_ENABLE(port);
188 * port is locked and interrupts are disabled
189 * uart_start( ) calls us under the port spinlock irqsave
191 static void arc_serial_start_tx(struct uart_port *port)
193 arc_serial_tx_chars(port);
196 static void arc_serial_rx_chars(struct uart_port *port, unsigned int status)
199 * UART has 4 deep RX-FIFO. Driver's recongnition of this fact
200 * is very subtle. Here's how ...
201 * Upon getting a RX-Intr, such that RX-EMPTY=0, meaning data available,
202 * driver reads the DATA Reg and keeps doing that in a loop, until
203 * RX-EMPTY=1. Multiple chars being avail, with a single Interrupt,
204 * before RX-EMPTY=0, implies some sort of buffering going on in the
205 * controller, which is indeed the Rx-FIFO.
208 u8 ch, flg = TTY_NORMAL;
211 * This could be an Rx Intr for err (no data),
212 * so check err and clear that Intr first
214 if (status & RXOERR) {
215 port->icount.overrun++;
217 UART_CLR_STATUS(port, RXOERR);
220 if (status & RXFERR) {
221 port->icount.frame++;
223 UART_CLR_STATUS(port, RXFERR);
226 if (status & RXEMPTY)
229 ch = UART_GET_DATA(port);
232 if (!(uart_handle_sysrq_char(port, ch)))
233 uart_insert_char(port, status, RXOERR, ch, flg);
235 tty_flip_buffer_push(&port->state->port);
236 } while (!((status = UART_GET_STATUS(port)) & RXEMPTY));
240 * A note on the Interrupt handling state machine of this driver
242 * kernel printk writes funnel thru the console driver framework and in order
243 * to keep things simple as well as efficient, it writes to UART in polled
244 * mode, in one shot, and exits.
246 * OTOH, Userland output (via tty layer), uses interrupt based writes as there
247 * can be undeterministic delay between char writes.
249 * Thus Rx-interrupts are always enabled, while tx-interrupts are by default
252 * When tty has some data to send out, serial core calls driver's start_tx
254 * -checks-if-tty-buffer-has-char-to-send
255 * -writes-data-to-uart
258 * Once data bits are pushed out, controller raises the Tx-room-avail-Interrupt.
259 * The first thing Tx ISR does is disable further Tx interrupts (as this could
260 * be the last char to send, before settling down into the quiet polled mode).
261 * It then calls the exact routine used by tty layer write to send out any
262 * more char in tty buffer. In case of sending, it re-enables Tx-intr. In case
263 * of no data, it remains disabled.
264 * This is how the transmit state machine is dynamically switched on/off
267 static irqreturn_t arc_serial_isr(int irq, void *dev_id)
269 struct uart_port *port = dev_id;
272 status = UART_GET_STATUS(port);
275 * Single IRQ for both Rx (data available) Tx (room available) Interrupt
276 * notifications from the UART Controller.
277 * To demultiplex between the two, we check the relevant bits
279 if (status & RXIENB) {
281 /* already in ISR, no need of xx_irqsave */
282 spin_lock(&port->lock);
283 arc_serial_rx_chars(port, status);
284 spin_unlock(&port->lock);
287 if ((status & TXIENB) && (status & TXEMPTY)) {
289 /* Unconditionally disable further Tx-Interrupts.
290 * will be enabled by tx_chars() if needed.
292 UART_TX_IRQ_DISABLE(port);
294 spin_lock(&port->lock);
296 if (!uart_tx_stopped(port))
297 arc_serial_tx_chars(port);
299 spin_unlock(&port->lock);
305 static unsigned int arc_serial_get_mctrl(struct uart_port *port)
308 * Pretend we have a Modem status reg and following bits are
309 * always set, to satify the serial core state machine
310 * (DSR) Data Set Ready
311 * (CTS) Clear To Send
312 * (CAR) Carrier Detect
314 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
317 static void arc_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
319 /* MCR not present */
322 static void arc_serial_break_ctl(struct uart_port *port, int break_state)
324 /* ARC UART doesn't support sending Break signal */
327 static int arc_serial_startup(struct uart_port *port)
329 /* Before we hook up the ISR, Disable all UART Interrupts */
330 UART_ALL_IRQ_DISABLE(port);
332 if (request_irq(port->irq, arc_serial_isr, 0, "arc uart rx-tx", port)) {
333 dev_warn(port->dev, "Unable to attach ARC UART intr\n");
337 UART_RX_IRQ_ENABLE(port); /* Only Rx IRQ enabled to begin with */
342 /* This is not really needed */
343 static void arc_serial_shutdown(struct uart_port *port)
345 free_irq(port->irq, port);
349 arc_serial_set_termios(struct uart_port *port, struct ktermios *new,
350 const struct ktermios *old)
352 struct arc_uart_port *uart = to_arc_port(port);
353 unsigned int baud, uartl, uarth, hw_val;
357 * Use the generic handler so that any specially encoded baud rates
358 * such as SPD_xx flags or "%B0" can be handled
359 * Max Baud I suppose will not be more than current 115K * 4
360 * Formula for ARC UART is: hw-val = ((CLK/(BAUD*4)) -1)
361 * spread over two 8-bit registers
363 baud = uart_get_baud_rate(port, new, old, 0, 460800);
365 hw_val = port->uartclk / (uart->baud * 4) - 1;
366 uartl = hw_val & 0xFF;
367 uarth = (hw_val >> 8) & 0xFF;
369 spin_lock_irqsave(&port->lock, flags);
371 UART_ALL_IRQ_DISABLE(port);
373 UART_SET_BAUDL(port, uartl);
374 UART_SET_BAUDH(port, uarth);
376 UART_RX_IRQ_ENABLE(port);
379 * UART doesn't support Parity/Hardware Flow Control;
380 * Only supports 8N1 character size
382 new->c_cflag &= ~(CMSPAR|CRTSCTS|CSIZE);
386 tty_termios_copy_hw(new, old);
388 /* Don't rewrite B0 */
389 if (tty_termios_baud_rate(new))
390 tty_termios_encode_baud_rate(new, baud, baud);
392 uart_update_timeout(port, new->c_cflag, baud);
394 spin_unlock_irqrestore(&port->lock, flags);
397 static const char *arc_serial_type(struct uart_port *port)
399 return port->type == PORT_ARC ? DRIVER_NAME : NULL;
402 static void arc_serial_release_port(struct uart_port *port)
406 static int arc_serial_request_port(struct uart_port *port)
412 * Verify the new serial_struct (for TIOCSSERIAL).
415 arc_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
417 if (port->type != PORT_UNKNOWN && ser->type != PORT_ARC)
424 * Configure/autoconfigure the port.
426 static void arc_serial_config_port(struct uart_port *port, int flags)
428 if (flags & UART_CONFIG_TYPE)
429 port->type = PORT_ARC;
432 #ifdef CONFIG_CONSOLE_POLL
434 static void arc_serial_poll_putchar(struct uart_port *port, unsigned char chr)
436 while (!(UART_GET_STATUS(port) & TXEMPTY))
439 UART_SET_DATA(port, chr);
442 static int arc_serial_poll_getchar(struct uart_port *port)
446 while (!(UART_GET_STATUS(port) & RXEMPTY))
449 chr = UART_GET_DATA(port);
454 static const struct uart_ops arc_serial_pops = {
455 .tx_empty = arc_serial_tx_empty,
456 .set_mctrl = arc_serial_set_mctrl,
457 .get_mctrl = arc_serial_get_mctrl,
458 .stop_tx = arc_serial_stop_tx,
459 .start_tx = arc_serial_start_tx,
460 .stop_rx = arc_serial_stop_rx,
461 .break_ctl = arc_serial_break_ctl,
462 .startup = arc_serial_startup,
463 .shutdown = arc_serial_shutdown,
464 .set_termios = arc_serial_set_termios,
465 .type = arc_serial_type,
466 .release_port = arc_serial_release_port,
467 .request_port = arc_serial_request_port,
468 .config_port = arc_serial_config_port,
469 .verify_port = arc_serial_verify_port,
470 #ifdef CONFIG_CONSOLE_POLL
471 .poll_put_char = arc_serial_poll_putchar,
472 .poll_get_char = arc_serial_poll_getchar,
476 #ifdef CONFIG_SERIAL_ARC_CONSOLE
478 static int arc_serial_console_setup(struct console *co, char *options)
480 struct uart_port *port;
486 if (co->index < 0 || co->index >= CONFIG_SERIAL_ARC_NR_PORTS)
490 * The uart port backing the console (e.g. ttyARC1) might not have been
491 * init yet. If so, defer the console setup to after the port.
493 port = &arc_uart_ports[co->index].port;
498 uart_parse_options(options, &baud, &parity, &bits, &flow);
501 * Serial core will call port->ops->set_termios( )
502 * which will set the baud reg
504 return uart_set_options(port, co, baud, parity, bits, flow);
507 static void arc_serial_console_putchar(struct uart_port *port, unsigned char ch)
509 while (!(UART_GET_STATUS(port) & TXEMPTY))
512 UART_SET_DATA(port, (unsigned char)ch);
516 * Interrupts are disabled on entering
518 static void arc_serial_console_write(struct console *co, const char *s,
521 struct uart_port *port = &arc_uart_ports[co->index].port;
524 spin_lock_irqsave(&port->lock, flags);
525 uart_console_write(port, s, count, arc_serial_console_putchar);
526 spin_unlock_irqrestore(&port->lock, flags);
529 static struct console arc_console = {
530 .name = ARC_SERIAL_DEV_NAME,
531 .write = arc_serial_console_write,
532 .device = uart_console_device,
533 .setup = arc_serial_console_setup,
534 .flags = CON_PRINTBUFFER,
536 .data = &arc_uart_driver
539 static void arc_early_serial_write(struct console *con, const char *s,
542 struct earlycon_device *dev = con->data;
544 uart_console_write(&dev->port, s, n, arc_serial_console_putchar);
547 static int __init arc_early_console_setup(struct earlycon_device *dev,
550 struct uart_port *port = &dev->port;
551 unsigned int l, h, hw_val;
553 if (!dev->port.membase)
556 hw_val = port->uartclk / (dev->baud * 4) - 1;
558 h = (hw_val >> 8) & 0xFF;
560 UART_SET_BAUDL(port, l);
561 UART_SET_BAUDH(port, h);
563 dev->con->write = arc_early_serial_write;
566 OF_EARLYCON_DECLARE(arc_uart, "snps,arc-uart", arc_early_console_setup);
568 #endif /* CONFIG_SERIAL_ARC_CONSOLE */
570 static int arc_serial_probe(struct platform_device *pdev)
572 struct device_node *np = pdev->dev.of_node;
573 struct arc_uart_port *uart;
574 struct uart_port *port;
578 /* no device tree device */
582 dev_id = of_alias_get_id(np, "serial");
586 if (dev_id >= ARRAY_SIZE(arc_uart_ports)) {
587 dev_err(&pdev->dev, "serial%d out of range\n", dev_id);
591 uart = &arc_uart_ports[dev_id];
594 if (of_property_read_u32(np, "clock-frequency", &val)) {
595 dev_err(&pdev->dev, "clock-frequency property NOTset\n");
600 if (of_property_read_u32(np, "current-speed", &val)) {
601 dev_err(&pdev->dev, "current-speed property NOT set\n");
606 port->membase = devm_platform_ioremap_resource(pdev, 0);
607 if (IS_ERR(port->membase)) {
608 /* No point of dev_err since UART itself is hosed here */
609 return PTR_ERR(port->membase);
612 port->irq = irq_of_parse_and_map(np, 0);
614 port->dev = &pdev->dev;
615 port->iotype = UPIO_MEM;
616 port->flags = UPF_BOOT_AUTOCONF;
618 port->ops = &arc_serial_pops;
619 port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_ARC_CONSOLE);
621 port->fifosize = ARC_UART_TX_FIFO_SIZE;
624 * uart_insert_char( ) uses it in decideding whether to ignore a
625 * char or not. Explicitly setting it here, removes the subtelty
627 port->ignore_status_mask = 0;
629 return uart_add_one_port(&arc_uart_driver, &arc_uart_ports[dev_id].port);
632 static const struct of_device_id arc_uart_dt_ids[] = {
633 { .compatible = "snps,arc-uart" },
636 MODULE_DEVICE_TABLE(of, arc_uart_dt_ids);
638 static struct platform_driver arc_platform_driver = {
639 .probe = arc_serial_probe,
642 .of_match_table = arc_uart_dt_ids,
646 static int __init arc_serial_init(void)
650 ret = uart_register_driver(&arc_uart_driver);
654 ret = platform_driver_register(&arc_platform_driver);
656 uart_unregister_driver(&arc_uart_driver);
661 static void __exit arc_serial_exit(void)
663 platform_driver_unregister(&arc_platform_driver);
664 uart_unregister_driver(&arc_uart_driver);
667 module_init(arc_serial_init);
668 module_exit(arc_serial_exit);
670 MODULE_LICENSE("GPL");
671 MODULE_ALIAS("platform:" DRIVER_NAME);
672 MODULE_AUTHOR("Vineet Gupta");
673 MODULE_DESCRIPTION("ARC(Synopsys) On-Chip(fpga) serial driver");