4 The "Serial Peripheral Interface" is a low level synchronous
5 protocol. Chips that support SPI can have data transfer rates
6 up to several tens of Mbit/sec. Chips are addressed with a
7 controller and a chipselect. Most SPI slaves don't support
8 dynamic device discovery; some are even write-only or read-only.
10 SPI is widely used by microcontrollers to talk with sensors,
11 eeprom and flash memory, codecs and various other controller
12 chips, analog to digital (and d-to-a) converters, and more.
13 MMC and SD cards can be accessed using SPI protocol; and for
14 DataFlash cards used in MMC sockets, SPI must always be used.
16 SPI is one of a family of similar protocols using a four wire
17 interface (select, clock, data in, data out) including Microwire
18 (half duplex), SSP, SSI, and PSP. This driver framework should
19 work with most such devices and controllers.
24 bool "Enable Driver Model for SPI drivers"
27 Enable driver model for SPI. The SPI slave interface
28 (spi_setup_slave(), spi_xfer(), etc.) is then implemented by
29 the SPI uclass. Drivers provide methods to access the SPI
30 buses that they control. The uclass interface is defined in
31 include/spi.h. The existing spi_slave structure is attached
32 as 'parent data' to every slave on each bus. Slaves
33 typically use driver-private data instead of extending the
37 bool "SPI memory extension"
39 Enable this option if you want to enable the SPI memory extension.
40 This extension is meant to simplify interaction with SPI memories
41 by providing an high-level interface to send memory-like commands.
46 bool "Altera SPI driver"
48 Enable the Altera SPI driver. This driver can be used to
49 access the SPI NOR flash on platforms embedding this Altera
50 IP core. Please find details on the "Embedded Peripherals IP
51 User Guide" of Altera.
54 bool "Andestech ATCSPI200 SPI driver"
56 Enable the Andestech ATCSPI200 SPI driver. This driver can be
57 used to access the SPI flash on AE3XX and AE250 platforms embedding
58 this Andestech IP core.
61 bool "Atheros SPI driver"
64 Enable the Atheros ar7xxx/ar9xxx SoC SPI driver, it was used
65 to access SPI NOR flash and other SPI peripherals. This driver
66 uses driver model and requires a device tree binding to operate.
67 please refer to doc/device-tree-bindings/spi/spi-ath79.txt.
70 bool "Atmel Quad SPI Controller"
73 Enable the Atmel Quad SPI controller in master mode. This driver
74 does not support generic SPI. The implementation supports only the
78 bool "Atmel SPI driver"
79 default y if ARCH_AT91
81 This enables driver for the Atmel SPI Controller, present on
82 many AT91 (ARM) chips. This driver can be used to access
83 the SPI Flash, such as AT25DF321.
86 bool "BCM63XX HSSPI driver"
87 depends on (ARCH_BMIPS || ARCH_BCM68360 || \
88 ARCH_BCM6858 || ARCH_BCM63158)
90 Enable the BCM6328 HSSPI driver. This driver can be used to
91 access the SPI NOR flash on platforms embedding this Broadcom
95 bool "BCM6348 SPI driver"
98 Enable the BCM6348/BCM6358 SPI driver. This driver can be used to
99 access the SPI NOR flash on platforms embedding these Broadcom
103 bool "BCMSTB SPI driver"
105 Enable the Broadcom set-top box SPI driver. This driver can
106 be used to access the SPI flash on platforms embedding this
109 config CORTINA_SFLASH
110 bool "Cortina-Access Serial Flash controller driver"
111 depends on DM_SPI && SPI_MEM
113 Enable the Cortina-Access Serial Flash controller driver. This driver
114 can be used to access the SPI NOR/NAND flash on platforms embedding this
115 Cortina-Access IP core.
118 bool "Cadence QSPI driver"
120 Enable the Cadence Quad-SPI (QSPI) driver. This driver can be
121 used to access the SPI NOR flash on platforms embedding this
125 bool "ColdFire SPI driver"
127 Enable the ColdFire SPI driver. This driver can be used on
131 bool "Davinci & Keystone SPI driver"
132 depends on ARCH_DAVINCI || ARCH_KEYSTONE
134 Enable the Davinci SPI driver
136 config DESIGNWARE_SPI
137 bool "Designware SPI driver"
139 Enable the Designware SPI driver. This driver can be used to
140 access the SPI NOR flash on platforms embedding this Designware
144 bool "Samsung Exynos SPI driver"
146 Enable the Samsung Exynos SPI driver. This driver can be used to
147 access the SPI NOR flash on platforms embedding this Samsung
151 bool "Freescale DSPI driver"
153 Enable the Freescale DSPI driver. This driver can be used to
154 access the SPI NOR flash and SPI Data flash on platforms embedding
155 this Freescale DSPI IP core. LS102xA and Colibri VF50/VF61 platforms
159 bool "Freescale QSPI driver"
162 Enable the Freescale Quad-SPI (QSPI) driver. This driver can be
163 used to access the SPI NOR flash on platforms embedding this
166 config FSL_QSPI_AHB_FULL_MAP
167 bool "Use full AHB memory map space"
169 default y if ARCH_MX6 || ARCH_MX7 || ARCH_MX7ULP || ARCH_IMX8M
171 Enable the Freescale QSPI driver to use full AHB memory map space for
175 bool "Intel ICH SPI driver"
177 Enable the Intel ICH SPI driver. This driver can be used to
178 access the SPI NOR flash on platforms embedding this Intel
182 bool "Marvell Kirkwood SPI Driver"
184 Enable support for SPI on various Marvell SoCs, such as
185 Kirkwood and Armada 375.
188 bool "Amlogic Meson SPI Flash Controller driver"
189 depends on ARCH_MESON
191 Enable the Amlogic Meson SPI Flash Controller SPIFC) driver.
192 This driver can be used to access the SPI NOR flash chips on
196 bool "MPC8XX SPI Driver"
199 Enable support for SPI on MPC8XX
202 bool "MPC8XXX SPI Driver"
204 Enable support for SPI on the MPC8XXX PowerPC SoCs.
207 bool "MSCC bitbang SPI driver"
208 depends on SOC_VCOREIII
210 Enable MSCC bitbang SPI driver. This driver can be used on
214 bool "MediaTek MT7620 SPI driver"
215 depends on SOC_MT7620
217 Enable the MT7620 SPI driver. This driver can be used to access
218 generic SPI devices on MediaTek MT7620 SoC.
221 bool "MediaTek MT7621 SPI driver"
222 depends on SOC_MT7628
224 Enable the MT7621 SPI driver. This driver can be used to access
225 the SPI NOR flash on platforms embedding this Ralink / MediaTek
226 SPI core, like MT7621/7628/7688.
229 bool "Mediatek SPI-NOR controller driver"
232 Enable the Mediatek SPINOR controller driver. This driver has
233 better read/write performance with NOR.
236 bool "Mediatek SPI memory controller driver"
239 Enable the Mediatek SPI memory controller driver. This driver is
240 originally based on the MediaTek SNFI IP core. It can only be
241 used to access SPI memory devices like SPI-NOR or SPI-NAND on
242 platforms embedding this IP core, like MT7622/M7629.
244 config MVEBU_A3700_SPI
245 bool "Marvell Armada 3700 SPI driver"
246 select CLK_ARMADA_3720
248 Enable the Marvell Armada 3700 SPI driver. This driver can be
249 used to access the SPI NOR flash on platforms embedding this
253 bool "MXS SPI Driver"
255 Enable the MXS SPI controller driver. This driver can be used
256 on the i.MX23 and i.MX28 SoCs.
259 bool "Macronix MX25F0A SPI controller"
261 Enable the Macronix MX25F0A SPI controller driver. This driver
262 can be used to access the SPI flash on platforms embedding
263 this Macronix IP core.
266 bool "NXP FlexSPI driver"
269 Enable the NXP FlexSPI (FSPI) driver. This driver can be used to
270 access the SPI NOR flash on platforms embedding this NXP IP core.
273 bool "Octeon SPI driver"
274 depends on DM_PCI && (ARCH_OCTEON || ARCH_OCTEONTX || ARCH_OCTEONTX2)
276 Enable the Octeon SPI driver. This driver can be used to
277 access the SPI NOR flash on Octeon II/III and OcteonTX/TX2
281 bool "McSPI driver for OMAP"
283 SPI master controller for OMAP24XX and later Multichannel SPI
284 (McSPI). This driver be used to access SPI chips on platforms
285 embedding this OMAP3 McSPI IP core.
288 bool "Microchip PIC32 SPI driver"
289 depends on MACH_PIC32
291 Enable the Microchip PIC32 SPI driver. This driver can be used
292 to access the SPI NOR flash, MMC-over-SPI on platforms based on
293 Microchip PIC32 family devices.
296 bool "ARM AMBA PL022 SSP controller driver"
299 This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
300 controller. If you have an embedded system with an AMBA(R)
301 bus and a PL022 controller, say Y or M here.
304 bool "Qualcomm SPI controller with QUP interface"
305 depends on ARCH_IPQ40XX
307 Qualcomm Universal Peripheral (QUP) core is an AHB slave that
308 provides a common data path (an output FIFO and an input FIFO)
309 for serial peripheral interface (SPI) mini-core. SPI in master
310 mode supports up to 50MHz, up to four chip selects, programmable
311 data path from 4 bits to 32 bits and numerous protocol variants.
313 config RENESAS_RPC_SPI
314 bool "Renesas RPC SPI driver"
315 depends on RCAR_GEN3 || RZA1
318 Enable the Renesas RPC SPI driver, used to access SPI NOR flash
319 on Renesas RCar Gen3 SoCs. This uses driver model and requires a
320 device tree binding to operate.
323 bool "Rockchip SPI driver"
325 Enable the Rockchip SPI driver, used to access SPI NOR flash and
326 other SPI peripherals (such as the Chrome OS EC) on Rockchip SoCs.
327 This uses driver model and requires a device tree binding to
331 bool "Sandbox SPI driver"
332 depends on SANDBOX && DM
334 Enable SPI support for sandbox. This is an emulation of a real SPI
335 bus. Devices can be attached to the bus using the device tree
336 which specifies the driver to use. As an example, see this device
337 tree fragment from sandbox.dts. It shows that the SPI bus has a
338 single flash device on chip select 0 which is emulated by the driver
339 for "sandbox,spi-flash", which is in drivers/mtd/spi/sandbox.c.
342 #address-cells = <1>;
345 compatible = "sandbox,spi";
346 cs-gpios = <0>, <&gpio_a 0>;
349 compatible = "spansion,m25p16", "jedec,spi-nor";
350 spi-max-frequency = <40000000>;
351 sandbox,filename = "spi.bin";
356 bool "SiFive SPI driver"
358 This driver supports the SiFive SPI IP. If unsure say N.
359 Enable the SiFive SPI controller driver.
361 The SiFive SPI controller driver is found on various SiFive SoCs.
364 bool "Soft SPI driver"
366 Enable Soft SPI driver. This driver is to use GPIO simulate
370 bool "Allwinner SoC SPI controllers"
373 Enable the Allwinner SoC SPi controller driver.
375 Same controller driver can reuse in all Allwinner SoC variants.
378 bool "STM32F7 QSPI driver"
379 depends on STM32F4 || STM32F7 || ARCH_STM32MP
381 Enable the STM32F7 Quad-SPI (QSPI) driver. This driver can be
382 used to access the SPI NOR flash chips on platforms embedding
386 bool "STM32 SPI driver"
387 depends on ARCH_STM32MP
389 Enable the STM32 Serial Peripheral Interface (SPI) driver for STM32MP
390 SoCs. This uses driver model and requires a device tree binding to
394 bool "nVidia Tegra114 SPI driver"
396 Enable the nVidia Tegra114 SPI driver. This driver can be used to
397 access the SPI NOR flash on platforms embedding this nVidia Tegra114
400 This controller is different than the older SoCs SPI controller and
401 also register interface get changed with this controller.
403 config TEGRA20_SFLASH
404 bool "nVidia Tegra20 Serial Flash controller driver"
406 Enable the nVidia Tegra20 Serial Flash controller driver. This driver
407 can be used to access the SPI NOR flash on platforms embedding this
408 nVidia Tegra20 IP core.
411 bool "nVidia Tegra20/Tegra30 SLINK driver"
413 Enable the nVidia Tegra20/Tegra30 SLINK driver. This driver can
414 be used to access the SPI NOR flash on platforms embedding this
415 nVidia Tegra20/Tegra30 IP cores.
418 bool "nVidia Tegra210 QSPI driver"
420 Enable the Tegra Quad-SPI (QSPI) driver for T210. This driver
421 be used to access SPI chips on platforms embedding this
422 NVIDIA Tegra210 IP core.
425 bool "TI QSPI driver"
428 Enable the TI Quad-SPI (QSPI) driver for DRA7xx and AM43xx evms.
429 This driver support spi flash single, quad and memory reads.
432 bool "Socionext UniPhier SPI driver"
433 depends on ARCH_UNIPHIER
435 Enable the Socionext UniPhier SPI driver. This driver can
436 be used to access SPI chips on platforms embedding this
440 bool "Xilinx SPI driver"
442 Enable the Xilinx SPI driver from the Xilinx EDK. This SPI
443 controller support 8 bit SPI transfers only, with or w/o FIFO.
444 For more info on Xilinx SPI Register Definitions and Overview
445 see driver file - drivers/spi/xilinx_spi.c
448 bool "Zynq SPI driver"
450 Enable the Zynq SPI driver. This driver can be used to
451 access the SPI NOR flash on platforms embedding this Zynq
455 bool "Zynq QSPI driver"
458 Enable the Zynq Quad-SPI (QSPI) driver. This driver can be
459 used to access the SPI NOR flash on platforms embedding this
460 Zynq QSPI IP core. This IP is used to connect the flash in
461 4-bit qspi, 8-bit dual stacked and shared 4-bit dual parallel.
464 bool "Configure ZynqMP Generic QSPI"
466 This option is used to enable ZynqMP QSPI controller driver which
467 is used to communicate with qspi flash devices.
472 bool "Freescale eSPI driver"
475 Enable the Freescale eSPI driver. This driver can be used to
476 access the SPI interface and SPI NOR flash on platforms embedding
477 this Freescale eSPI IP core.
480 bool "Renesas Quad SPI driver"
482 Enable the Renesas Quad SPI controller driver. This driver can be
483 used on Renesas SoCs.
486 bool "MXC SPI Driver"
488 Enable the MXC SPI controller driver. This driver can be used
489 on various i.MX SoCs such as i.MX31/35/51/6/7.
492 bool "Socionext SynQuacer HS-SPI driver"
493 depends on ARCH_SYNQUACER
495 Enable the Socionext HS-SPI driver for SynQuacer. This driver can
496 be used to access the SPI interface and SPI NOR flash on platforms
497 embedding this HS-SPI IP core.
499 endif # menu "SPI Support"