drivers/serial/serial_stm32.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright (C) 2016, STMicroelectronics - All Rights Reserved
   4  * Author(s): Vikas Manocha, <vikas.manocha@st.com> for STMicroelectronics.
   5  */
   6
   7 #include <common.h>
   8 #include <clk.h>
   9 #include <dm.h>
  10 #include <reset.h>
  11 #include <serial.h>
  12 #include <watchdog.h>
  13 #include <asm/io.h>
  14 #include <asm/arch/stm32.h>
  15 #include "serial_stm32.h"
  16
  17 static void _stm32_serial_setbrg(fdt_addr_t base,
  18                                  struct stm32_uart_info *uart_info,
  19                                  u32 clock_rate,
  20                                  int baudrate)
  21 {
  22         bool stm32f4 = uart_info->stm32f4;
  23         u32 int_div, mantissa, fraction, oversampling;
  24
  25         int_div = DIV_ROUND_CLOSEST(clock_rate, baudrate);
  26
  27         if (int_div < 16) {
  28                 oversampling = 8;
  29                 setbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_OVER8);
  30         } else {
  31                 oversampling = 16;
  32                 clrbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_OVER8);
  33         }
  34
  35         mantissa = (int_div / oversampling) << USART_BRR_M_SHIFT;
  36         fraction = int_div % oversampling;
  37
  38         writel(mantissa | fraction, base + BRR_OFFSET(stm32f4));
  39 }
  40
  41 static int stm32_serial_setbrg(struct udevice *dev, int baudrate)
  42 {
  43         struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
  44
  45         _stm32_serial_setbrg(plat->base, plat->uart_info,
  46                              plat->clock_rate, baudrate);
  47
  48         return 0;
  49 }
  50
  51 static int stm32_serial_setconfig(struct udevice *dev, uint serial_config)
  52 {
  53         struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
  54         bool stm32f4 = plat->uart_info->stm32f4;
  55         u8 uart_enable_bit = plat->uart_info->uart_enable_bit;
  56         u32 cr1 = plat->base + CR1_OFFSET(stm32f4);
  57         u32 config = 0;
  58         uint parity = SERIAL_GET_PARITY(serial_config);
  59         uint bits = SERIAL_GET_BITS(serial_config);
  60         uint stop = SERIAL_GET_STOP(serial_config);
  61
  62         /*
  63          * only parity config is implemented, check if other serial settings
  64          * are the default one.
  65          * (STM32F4 serial IP didn't support parity setting)
  66          */
  67         if (bits != SERIAL_8_BITS || stop != SERIAL_ONE_STOP || stm32f4)
  68                 return -ENOTSUPP; /* not supported in driver*/
  69
  70         clrbits_le32(cr1, USART_CR1_RE | USART_CR1_TE | BIT(uart_enable_bit));
  71         /* update usart configuration (uart need to be disable)
  72          * PCE: parity check enable
  73          * PS : '0' : Even / '1' : Odd
  74          * M[1:0] = '00' : 8 Data bits
  75          * M[1:0] = '01' : 9 Data bits with parity
  76          */
  77         switch (parity) {
  78         default:
  79         case SERIAL_PAR_NONE:
  80                 config = 0;
  81                 break;
  82         case SERIAL_PAR_ODD:
  83                 config = USART_CR1_PCE | USART_CR1_PS | USART_CR1_M0;
  84                 break;
  85         case SERIAL_PAR_EVEN:
  86                 config = USART_CR1_PCE | USART_CR1_M0;
  87                 break;
  88         }
  89
  90         clrsetbits_le32(cr1,
  91                         USART_CR1_PCE | USART_CR1_PS | USART_CR1_M1 |
  92                         USART_CR1_M0,
  93                         config);
  94         setbits_le32(cr1, USART_CR1_RE | USART_CR1_TE | BIT(uart_enable_bit));
  95
  96         return 0;
  97 }
  98
  99 static int stm32_serial_getc(struct udevice *dev)
 100 {
 101         struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
 102         bool stm32f4 = plat->uart_info->stm32f4;
 103         fdt_addr_t base = plat->base;
 104         u32 isr = readl(base + ISR_OFFSET(stm32f4));
 105
 106         if ((isr & USART_ISR_RXNE) == 0)
 107                 return -EAGAIN;
 108
 109         if (isr & (USART_ISR_PE | USART_ISR_ORE)) {
 110                 if (!stm32f4)
 111                         setbits_le32(base + ICR_OFFSET,
 112                                      USART_ICR_PCECF | USART_ICR_ORECF);
 113                 else
 114                         readl(base + RDR_OFFSET(stm32f4));
 115                 return -EIO;
 116         }
 117
 118         return readl(base + RDR_OFFSET(stm32f4));
 119 }
 120
 121 static int _stm32_serial_putc(fdt_addr_t base,
 122                               struct stm32_uart_info *uart_info,
 123                               const char c)
 124 {
 125         bool stm32f4 = uart_info->stm32f4;
 126
 127         if ((readl(base + ISR_OFFSET(stm32f4)) & USART_ISR_TXE) == 0)
 128                 return -EAGAIN;
 129
 130         writel(c, base + TDR_OFFSET(stm32f4));
 131
 132         return 0;
 133 }
 134
 135 static int stm32_serial_putc(struct udevice *dev, const char c)
 136 {
 137         struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
 138
 139         return _stm32_serial_putc(plat->base, plat->uart_info, c);
 140 }
 141
 142 static int stm32_serial_pending(struct udevice *dev, bool input)
 143 {
 144         struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
 145         bool stm32f4 = plat->uart_info->stm32f4;
 146         fdt_addr_t base = plat->base;
 147
 148         if (input)
 149                 return readl(base + ISR_OFFSET(stm32f4)) &
 150                         USART_ISR_RXNE ? 1 : 0;
 151         else
 152                 return readl(base + ISR_OFFSET(stm32f4)) &
 153                         USART_ISR_TXE ? 0 : 1;
 154 }
 155
 156 static void _stm32_serial_init(fdt_addr_t base,
 157                                struct stm32_uart_info *uart_info)
 158 {
 159         bool stm32f4 = uart_info->stm32f4;
 160         u8 uart_enable_bit = uart_info->uart_enable_bit;
 161
 162         /* Disable uart-> enable fifo -> enable uart */
 163         clrbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_RE | USART_CR1_TE |
 164                      BIT(uart_enable_bit));
 165         if (uart_info->has_fifo)
 166                 setbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_FIFOEN);
 167         setbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_RE | USART_CR1_TE |
 168                      BIT(uart_enable_bit));
 169 }
 170
 171 static int stm32_serial_probe(struct udevice *dev)
 172 {
 173         struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
 174         struct clk clk;
 175         struct reset_ctl reset;
 176         int ret;
 177
 178         plat->uart_info = (struct stm32_uart_info *)dev_get_driver_data(dev);
 179
 180         ret = clk_get_by_index(dev, 0, &clk);
 181         if (ret < 0)
 182                 return ret;
 183
 184         ret = clk_enable(&clk);
 185         if (ret) {
 186                 dev_err(dev, "failed to enable clock\n");
 187                 return ret;
 188         }
 189
 190         ret = reset_get_by_index(dev, 0, &reset);
 191         if (!ret) {
 192                 reset_assert(&reset);
 193                 udelay(2);
 194                 reset_deassert(&reset);
 195         }
 196
 197         plat->clock_rate = clk_get_rate(&clk);
 198         if (plat->clock_rate < 0) {
 199                 clk_disable(&clk);
 200                 return plat->clock_rate;
 201         };
 202
 203         _stm32_serial_init(plat->base, plat->uart_info);
 204
 205         return 0;
 206 }
 207
 208 static const struct udevice_id stm32_serial_id[] = {
 209         { .compatible = "st,stm32-uart", .data = (ulong)&stm32f4_info},
 210         { .compatible = "st,stm32f7-uart", .data = (ulong)&stm32f7_info},
 211         { .compatible = "st,stm32h7-uart", .data = (ulong)&stm32h7_info},
 212         {}
 213 };
 214
 215 static int stm32_serial_ofdata_to_platdata(struct udevice *dev)
 216 {
 217         struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
 218
 219         plat->base = devfdt_get_addr(dev);
 220         if (plat->base == FDT_ADDR_T_NONE)
 221                 return -EINVAL;
 222
 223         return 0;
 224 }
 225
 226 static const struct dm_serial_ops stm32_serial_ops = {
 227         .putc = stm32_serial_putc,
 228         .pending = stm32_serial_pending,
 229         .getc = stm32_serial_getc,
 230         .setbrg = stm32_serial_setbrg,
 231         .setconfig = stm32_serial_setconfig
 232 };
 233
 234 U_BOOT_DRIVER(serial_stm32) = {
 235         .name = "serial_stm32",
 236         .id = UCLASS_SERIAL,
 237         .of_match = of_match_ptr(stm32_serial_id),
 238         .ofdata_to_platdata = of_match_ptr(stm32_serial_ofdata_to_platdata),
 239         .platdata_auto_alloc_size = sizeof(struct stm32x7_serial_platdata),
 240         .ops = &stm32_serial_ops,
 241         .probe = stm32_serial_probe,
 242 #if !CONFIG_IS_ENABLED(OF_CONTROL)
 243         .flags = DM_FLAG_PRE_RELOC,
 244 #endif
 245 };
 246
 247 #ifdef CONFIG_DEBUG_UART_STM32
 248 #include <debug_uart.h>
 249 static inline struct stm32_uart_info *_debug_uart_info(void)
 250 {
 251         struct stm32_uart_info *uart_info;
 252
 253 #if defined(CONFIG_STM32F4)
 254         uart_info = &stm32f4_info;
 255 #elif defined(CONFIG_STM32F7)
 256         uart_info = &stm32f7_info;
 257 #else
 258         uart_info = &stm32h7_info;
 259 #endif
 260         return uart_info;
 261 }
 262
 263 static inline void _debug_uart_init(void)
 264 {
 265         fdt_addr_t base = CONFIG_DEBUG_UART_BASE;
 266         struct stm32_uart_info *uart_info = _debug_uart_info();
 267
 268         _stm32_serial_init(base, uart_info);
 269         _stm32_serial_setbrg(base, uart_info,
 270                              CONFIG_DEBUG_UART_CLOCK,
 271                              CONFIG_BAUDRATE);
 272 }
 273
 274 static inline void _debug_uart_putc(int c)
 275 {
 276         fdt_addr_t base = CONFIG_DEBUG_UART_BASE;
 277         struct stm32_uart_info *uart_info = _debug_uart_info();
 278
 279         while (_stm32_serial_putc(base, uart_info, c) == -EAGAIN)
 280                 ;
 281 }
 282
 283 DEBUG_UART_FUNCS
 284 #endif