drivers/serial/bfin_5xx.c

   1 /*
   2  * Blackfin On-Chip Serial Driver
   3  *
   4  * Copyright 2006-2008 Analog Devices Inc.
   5  *
   6  * Enter bugs at http://blackfin.uclinux.org/
   7  *
   8  * Licensed under the GPL-2 or later.
   9  */
  10
  11 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  12 #define SUPPORT_SYSRQ
  13 #endif
  14
  15 #include <linux/module.h>
  16 #include <linux/ioport.h>
  17 #include <linux/init.h>
  18 #include <linux/console.h>
  19 #include <linux/sysrq.h>
  20 #include <linux/platform_device.h>
  21 #include <linux/tty.h>
  22 #include <linux/tty_flip.h>
  23 #include <linux/serial_core.h>
  24
  25 #ifdef CONFIG_KGDB_UART
  26 #include <linux/kgdb.h>
  27 #include <asm/irq_regs.h>
  28 #endif
  29
  30 #include <asm/gpio.h>
  31 #include <mach/bfin_serial_5xx.h>
  32
  33 #ifdef CONFIG_SERIAL_BFIN_DMA
  34 #include <linux/dma-mapping.h>
  35 #include <asm/io.h>
  36 #include <asm/irq.h>
  37 #include <asm/cacheflush.h>
  38 #endif
  39
  40 /* UART name and device definitions */
  41 #define BFIN_SERIAL_NAME        "ttyBF"
  42 #define BFIN_SERIAL_MAJOR       204
  43 #define BFIN_SERIAL_MINOR       64
  44
  45 static struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
  46 static int nr_active_ports = ARRAY_SIZE(bfin_serial_resource);
  47
  48 /*
  49  * Setup for console. Argument comes from the menuconfig
  50  */
  51 #define DMA_RX_XCOUNT           512
  52 #define DMA_RX_YCOUNT           (PAGE_SIZE / DMA_RX_XCOUNT)
  53
  54 #define DMA_RX_FLUSH_JIFFIES    (HZ / 50)
  55 #define CTS_CHECK_JIFFIES       (HZ / 50)
  56
  57 #ifdef CONFIG_SERIAL_BFIN_DMA
  58 static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
  59 #else
  60 static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
  61 #endif
  62
  63 static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
  64
  65 /*
  66  * interrupts are disabled on entry
  67  */
  68 static void bfin_serial_stop_tx(struct uart_port *port)
  69 {
  70         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
  71         struct circ_buf *xmit = &uart->port.info->xmit;
  72
  73         while (!(UART_GET_LSR(uart) & TEMT))
  74                 cpu_relax();
  75
  76 #ifdef CONFIG_SERIAL_BFIN_DMA
  77         disable_dma(uart->tx_dma_channel);
  78         xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
  79         uart->port.icount.tx += uart->tx_count;
  80         uart->tx_count = 0;
  81         uart->tx_done = 1;
  82 #else
  83 #ifdef CONFIG_BF54x
  84         /* Clear TFI bit */
  85         UART_PUT_LSR(uart, TFI);
  86 #endif
  87         UART_CLEAR_IER(uart, ETBEI);
  88 #endif
  89 }
  90
  91 /*
  92  * port is locked and interrupts are disabled
  93  */
  94 static void bfin_serial_start_tx(struct uart_port *port)
  95 {
  96         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
  97
  98 #ifdef CONFIG_SERIAL_BFIN_DMA
  99         if (uart->tx_done)
 100                 bfin_serial_dma_tx_chars(uart);
 101 #else
 102         UART_SET_IER(uart, ETBEI);
 103         bfin_serial_tx_chars(uart);
 104 #endif
 105 }
 106
 107 /*
 108  * Interrupts are enabled
 109  */
 110 static void bfin_serial_stop_rx(struct uart_port *port)
 111 {
 112         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 113 #ifdef CONFIG_KGDB_UART
 114         if (uart->port.line != CONFIG_KGDB_UART_PORT)
 115 #endif
 116         UART_CLEAR_IER(uart, ERBFI);
 117 }
 118
 119 /*
 120  * Set the modem control timer to fire immediately.
 121  */
 122 static void bfin_serial_enable_ms(struct uart_port *port)
 123 {
 124 }
 125
 126 #ifdef CONFIG_KGDB_UART
 127 static int kgdb_entry_state;
 128
 129 void kgdb_put_debug_char(int chr)
 130 {
 131         struct bfin_serial_port *uart;
 132
 133         if (CONFIG_KGDB_UART_PORT < 0
 134                 || CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS)
 135                 uart = &bfin_serial_ports[0];
 136         else
 137                 uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
 138
 139         while (!(UART_GET_LSR(uart) & THRE)) {
 140                 SSYNC();
 141         }
 142
 143         UART_CLEAR_DLAB(uart);
 144         UART_PUT_CHAR(uart, (unsigned char)chr);
 145         SSYNC();
 146 }
 147
 148 int kgdb_get_debug_char(void)
 149 {
 150         struct bfin_serial_port *uart;
 151         unsigned char chr;
 152
 153         if (CONFIG_KGDB_UART_PORT < 0
 154                 || CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS)
 155                 uart = &bfin_serial_ports[0];
 156         else
 157                 uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
 158
 159         while(!(UART_GET_LSR(uart) & DR)) {
 160                 SSYNC();
 161         }
 162         UART_CLEAR_DLAB(uart);
 163         chr = UART_GET_CHAR(uart);
 164         SSYNC();
 165
 166         return chr;
 167 }
 168 #endif
 169
 170 #if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO)
 171 # define UART_GET_ANOMALY_THRESHOLD(uart)    ((uart)->anomaly_threshold)
 172 # define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v))
 173 #else
 174 # define UART_GET_ANOMALY_THRESHOLD(uart)    0
 175 # define UART_SET_ANOMALY_THRESHOLD(uart, v)
 176 #endif
 177
 178 #ifdef CONFIG_SERIAL_BFIN_PIO
 179 static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
 180 {
 181         struct tty_struct *tty = uart->port.info->port.tty;
 182         unsigned int status, ch, flg;
 183         static struct timeval anomaly_start = { .tv_sec = 0 };
 184
 185         status = UART_GET_LSR(uart);
 186         UART_CLEAR_LSR(uart);
 187
 188         ch = UART_GET_CHAR(uart);
 189         uart->port.icount.rx++;
 190
 191 #ifdef CONFIG_KGDB_UART
 192         if (uart->port.line == CONFIG_KGDB_UART_PORT) {
 193                 struct pt_regs *regs = get_irq_regs();
 194                 if (uart->port.cons->index == CONFIG_KGDB_UART_PORT && ch == 0x1) { /* Ctrl + A */
 195                         kgdb_breakkey_pressed(regs);
 196                         return;
 197                 } else if (kgdb_entry_state == 0 && ch == '$') {/* connection from KGDB */
 198                         kgdb_entry_state = 1;
 199                 } else if (kgdb_entry_state == 1 && ch == 'q') {
 200                         kgdb_entry_state = 0;
 201                         kgdb_breakkey_pressed(regs);
 202                         return;
 203                 } else if (ch == 0x3) {/* Ctrl + C */
 204                         kgdb_entry_state = 0;
 205                         kgdb_breakkey_pressed(regs);
 206                         return;
 207                 } else {
 208                         kgdb_entry_state = 0;
 209                 }
 210         }
 211 #endif
 212
 213         if (ANOMALY_05000363) {
 214                 /* The BF533 (and BF561) family of processors have a nice anomaly
 215                  * where they continuously generate characters for a "single" break.
 216                  * We have to basically ignore this flood until the "next" valid
 217                  * character comes across.  Due to the nature of the flood, it is
 218                  * not possible to reliably catch bytes that are sent too quickly
 219                  * after this break.  So application code talking to the Blackfin
 220                  * which sends a break signal must allow at least 1.5 character
 221                  * times after the end of the break for things to stabilize.  This
 222                  * timeout was picked as it must absolutely be larger than 1
 223                  * character time +/- some percent.  So 1.5 sounds good.  All other
 224                  * Blackfin families operate properly.  Woo.
 225                  */
 226                 if (anomaly_start.tv_sec) {
 227                         struct timeval curr;
 228                         suseconds_t usecs;
 229
 230                         if ((~ch & (~ch + 1)) & 0xff)
 231                                 goto known_good_char;
 232
 233                         do_gettimeofday(&curr);
 234                         if (curr.tv_sec - anomaly_start.tv_sec > 1)
 235                                 goto known_good_char;
 236
 237                         usecs = 0;
 238                         if (curr.tv_sec != anomaly_start.tv_sec)
 239                                 usecs += USEC_PER_SEC;
 240                         usecs += curr.tv_usec - anomaly_start.tv_usec;
 241
 242                         if (usecs > UART_GET_ANOMALY_THRESHOLD(uart))
 243                                 goto known_good_char;
 244
 245                         if (ch)
 246                                 anomaly_start.tv_sec = 0;
 247                         else
 248                                 anomaly_start = curr;
 249
 250                         return;
 251
 252  known_good_char:
 253                         anomaly_start.tv_sec = 0;
 254                 }
 255         }
 256
 257         if (status & BI) {
 258                 if (ANOMALY_05000363)
 259                         if (bfin_revid() < 5)
 260                                 do_gettimeofday(&anomaly_start);
 261                 uart->port.icount.brk++;
 262                 if (uart_handle_break(&uart->port))
 263                         goto ignore_char;
 264                 status &= ~(PE | FE);
 265         }
 266         if (status & PE)
 267                 uart->port.icount.parity++;
 268         if (status & OE)
 269                 uart->port.icount.overrun++;
 270         if (status & FE)
 271                 uart->port.icount.frame++;
 272
 273         status &= uart->port.read_status_mask;
 274
 275         if (status & BI)
 276                 flg = TTY_BREAK;
 277         else if (status & PE)
 278                 flg = TTY_PARITY;
 279         else if (status & FE)
 280                 flg = TTY_FRAME;
 281         else
 282                 flg = TTY_NORMAL;
 283
 284         if (uart_handle_sysrq_char(&uart->port, ch))
 285                 goto ignore_char;
 286
 287         uart_insert_char(&uart->port, status, OE, ch, flg);
 288
 289  ignore_char:
 290         tty_flip_buffer_push(tty);
 291 }
 292
 293 static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
 294 {
 295         struct circ_buf *xmit = &uart->port.info->xmit;
 296
 297         /*
 298          * Check the modem control lines before
 299          * transmitting anything.
 300          */
 301         bfin_serial_mctrl_check(uart);
 302
 303         if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
 304 #ifdef CONFIG_BF54x
 305                 /* Clear TFI bit */
 306                 UART_PUT_LSR(uart, TFI);
 307 #endif
 308                 UART_CLEAR_IER(uart, ETBEI);
 309                 return;
 310         }
 311
 312         if (uart->port.x_char) {
 313                 UART_PUT_CHAR(uart, uart->port.x_char);
 314                 uart->port.icount.tx++;
 315                 uart->port.x_char = 0;
 316         }
 317
 318         while ((UART_GET_LSR(uart) & THRE) && xmit->tail != xmit->head) {
 319                 UART_PUT_CHAR(uart, xmit->buf[xmit->tail]);
 320                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 321                 uart->port.icount.tx++;
 322                 SSYNC();
 323         }
 324
 325         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 326                 uart_write_wakeup(&uart->port);
 327 }
 328
 329 static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id)
 330 {
 331         struct bfin_serial_port *uart = dev_id;
 332
 333         spin_lock(&uart->port.lock);
 334         while (UART_GET_LSR(uart) & DR)
 335                 bfin_serial_rx_chars(uart);
 336         spin_unlock(&uart->port.lock);
 337
 338         return IRQ_HANDLED;
 339 }
 340
 341 static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
 342 {
 343         struct bfin_serial_port *uart = dev_id;
 344
 345         spin_lock(&uart->port.lock);
 346         if (UART_GET_LSR(uart) & THRE)
 347                 bfin_serial_tx_chars(uart);
 348         spin_unlock(&uart->port.lock);
 349
 350         return IRQ_HANDLED;
 351 }
 352 #endif
 353
 354 #ifdef CONFIG_SERIAL_BFIN_DMA
 355 static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
 356 {
 357         struct circ_buf *xmit = &uart->port.info->xmit;
 358
 359         uart->tx_done = 0;
 360
 361         /*
 362          * Check the modem control lines before
 363          * transmitting anything.
 364          */
 365         bfin_serial_mctrl_check(uart);
 366
 367         if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
 368                 uart->tx_count = 0;
 369                 uart->tx_done = 1;
 370                 return;
 371         }
 372
 373         if (uart->port.x_char) {
 374                 UART_PUT_CHAR(uart, uart->port.x_char);
 375                 uart->port.icount.tx++;
 376                 uart->port.x_char = 0;
 377         }
 378
 379         uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
 380         if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
 381                 uart->tx_count = UART_XMIT_SIZE - xmit->tail;
 382         blackfin_dcache_flush_range((unsigned long)(xmit->buf+xmit->tail),
 383                                         (unsigned long)(xmit->buf+xmit->tail+uart->tx_count));
 384         set_dma_config(uart->tx_dma_channel,
 385                 set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
 386                         INTR_ON_BUF,
 387                         DIMENSION_LINEAR,
 388                         DATA_SIZE_8,
 389                         DMA_SYNC_RESTART));
 390         set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
 391         set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
 392         set_dma_x_modify(uart->tx_dma_channel, 1);
 393         enable_dma(uart->tx_dma_channel);
 394
 395         UART_SET_IER(uart, ETBEI);
 396 }
 397
 398 static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
 399 {
 400         struct tty_struct *tty = uart->port.info->port.tty;
 401         int i, flg, status;
 402
 403         status = UART_GET_LSR(uart);
 404         UART_CLEAR_LSR(uart);
 405
 406         uart->port.icount.rx +=
 407                 CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail,
 408                 UART_XMIT_SIZE);
 409
 410         if (status & BI) {
 411                 uart->port.icount.brk++;
 412                 if (uart_handle_break(&uart->port))
 413                         goto dma_ignore_char;
 414                 status &= ~(PE | FE);
 415         }
 416         if (status & PE)
 417                 uart->port.icount.parity++;
 418         if (status & OE)
 419                 uart->port.icount.overrun++;
 420         if (status & FE)
 421                 uart->port.icount.frame++;
 422
 423         status &= uart->port.read_status_mask;
 424
 425         if (status & BI)
 426                 flg = TTY_BREAK;
 427         else if (status & PE)
 428                 flg = TTY_PARITY;
 429         else if (status & FE)
 430                 flg = TTY_FRAME;
 431         else
 432                 flg = TTY_NORMAL;
 433
 434         for (i = uart->rx_dma_buf.tail; i != uart->rx_dma_buf.head; i++) {
 435                 if (i >= UART_XMIT_SIZE)
 436                         i = 0;
 437                 if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
 438                         uart_insert_char(&uart->port, status, OE,
 439                                 uart->rx_dma_buf.buf[i], flg);
 440         }
 441
 442  dma_ignore_char:
 443         tty_flip_buffer_push(tty);
 444 }
 445
 446 void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
 447 {
 448         int x_pos, pos;
 449
 450         uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
 451         x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
 452         uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
 453         if (uart->rx_dma_nrows == DMA_RX_YCOUNT)
 454                 uart->rx_dma_nrows = 0;
 455         x_pos = DMA_RX_XCOUNT - x_pos;
 456         if (x_pos == DMA_RX_XCOUNT)
 457                 x_pos = 0;
 458
 459         pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
 460         if (pos != uart->rx_dma_buf.tail) {
 461                 uart->rx_dma_buf.head = pos;
 462                 bfin_serial_dma_rx_chars(uart);
 463                 uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
 464         }
 465
 466         mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
 467 }
 468
 469 static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
 470 {
 471         struct bfin_serial_port *uart = dev_id;
 472         struct circ_buf *xmit = &uart->port.info->xmit;
 473
 474         spin_lock(&uart->port.lock);
 475         if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
 476                 disable_dma(uart->tx_dma_channel);
 477                 clear_dma_irqstat(uart->tx_dma_channel);
 478                 UART_CLEAR_IER(uart, ETBEI);
 479                 xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
 480                 uart->port.icount.tx += uart->tx_count;
 481
 482                 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 483                         uart_write_wakeup(&uart->port);
 484
 485                 bfin_serial_dma_tx_chars(uart);
 486         }
 487
 488         spin_unlock(&uart->port.lock);
 489         return IRQ_HANDLED;
 490 }
 491
 492 static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
 493 {
 494         struct bfin_serial_port *uart = dev_id;
 495         unsigned short irqstat;
 496
 497         spin_lock(&uart->port.lock);
 498         irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
 499         clear_dma_irqstat(uart->rx_dma_channel);
 500         spin_unlock(&uart->port.lock);
 501
 502         mod_timer(&(uart->rx_dma_timer), jiffies);
 503
 504         return IRQ_HANDLED;
 505 }
 506 #endif
 507
 508 /*
 509  * Return TIOCSER_TEMT when transmitter is not busy.
 510  */
 511 static unsigned int bfin_serial_tx_empty(struct uart_port *port)
 512 {
 513         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 514         unsigned short lsr;
 515
 516         lsr = UART_GET_LSR(uart);
 517         if (lsr & TEMT)
 518                 return TIOCSER_TEMT;
 519         else
 520                 return 0;
 521 }
 522
 523 static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
 524 {
 525 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
 526         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 527         if (uart->cts_pin < 0)
 528                 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
 529
 530         if (UART_GET_CTS(uart))
 531                 return TIOCM_DSR | TIOCM_CAR;
 532         else
 533 #endif
 534                 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
 535 }
 536
 537 static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
 538 {
 539 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
 540         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 541         if (uart->rts_pin < 0)
 542                 return;
 543
 544         if (mctrl & TIOCM_RTS)
 545                 UART_CLEAR_RTS(uart);
 546         else
 547                 UART_SET_RTS(uart);
 548 #endif
 549 }
 550
 551 /*
 552  * Handle any change of modem status signal since we were last called.
 553  */
 554 static void bfin_serial_mctrl_check(struct bfin_serial_port *uart)
 555 {
 556 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
 557         unsigned int status;
 558         struct uart_info *info = uart->port.info;
 559         struct tty_struct *tty = info->port.tty;
 560
 561         status = bfin_serial_get_mctrl(&uart->port);
 562         uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
 563         if (!(status & TIOCM_CTS)) {
 564                 tty->hw_stopped = 1;
 565                 uart->cts_timer.data = (unsigned long)(uart);
 566                 uart->cts_timer.function = (void *)bfin_serial_mctrl_check;
 567                 uart->cts_timer.expires = jiffies + CTS_CHECK_JIFFIES;
 568                 add_timer(&(uart->cts_timer));
 569         } else {
 570                 tty->hw_stopped = 0;
 571         }
 572 #endif
 573 }
 574
 575 /*
 576  * Interrupts are always disabled.
 577  */
 578 static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
 579 {
 580         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 581         u16 lcr = UART_GET_LCR(uart);
 582         if (break_state)
 583                 lcr |= SB;
 584         else
 585                 lcr &= ~SB;
 586         UART_PUT_LCR(uart, lcr);
 587         SSYNC();
 588 }
 589
 590 static int bfin_serial_startup(struct uart_port *port)
 591 {
 592         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 593
 594 #ifdef CONFIG_SERIAL_BFIN_DMA
 595         dma_addr_t dma_handle;
 596
 597         if (request_dma(uart->rx_dma_channel, "BFIN_UART_RX") < 0) {
 598                 printk(KERN_NOTICE "Unable to attach Blackfin UART RX DMA channel\n");
 599                 return -EBUSY;
 600         }
 601
 602         if (request_dma(uart->tx_dma_channel, "BFIN_UART_TX") < 0) {
 603                 printk(KERN_NOTICE "Unable to attach Blackfin UART TX DMA channel\n");
 604                 free_dma(uart->rx_dma_channel);
 605                 return -EBUSY;
 606         }
 607
 608         set_dma_callback(uart->rx_dma_channel, bfin_serial_dma_rx_int, uart);
 609         set_dma_callback(uart->tx_dma_channel, bfin_serial_dma_tx_int, uart);
 610
 611         uart->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA);
 612         uart->rx_dma_buf.head = 0;
 613         uart->rx_dma_buf.tail = 0;
 614         uart->rx_dma_nrows = 0;
 615
 616         set_dma_config(uart->rx_dma_channel,
 617                 set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
 618                                 INTR_ON_ROW, DIMENSION_2D,
 619                                 DATA_SIZE_8,
 620                                 DMA_SYNC_RESTART));
 621         set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT);
 622         set_dma_x_modify(uart->rx_dma_channel, 1);
 623         set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT);
 624         set_dma_y_modify(uart->rx_dma_channel, 1);
 625         set_dma_start_addr(uart->rx_dma_channel, (unsigned long)uart->rx_dma_buf.buf);
 626         enable_dma(uart->rx_dma_channel);
 627
 628         uart->rx_dma_timer.data = (unsigned long)(uart);
 629         uart->rx_dma_timer.function = (void *)bfin_serial_rx_dma_timeout;
 630         uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
 631         add_timer(&(uart->rx_dma_timer));
 632 #else
 633         if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
 634              "BFIN_UART_RX", uart)) {
 635 # ifdef CONFIG_KGDB_UART
 636                 if (uart->port.line != CONFIG_KGDB_UART_PORT) {
 637 # endif
 638                 printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
 639                 return -EBUSY;
 640 # ifdef CONFIG_KGDB_UART
 641                 }
 642 # endif
 643         }
 644
 645         if (request_irq
 646             (uart->port.irq+1, bfin_serial_tx_int, IRQF_DISABLED,
 647              "BFIN_UART_TX", uart)) {
 648                 printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n");
 649                 free_irq(uart->port.irq, uart);
 650                 return -EBUSY;
 651         }
 652 #endif
 653         UART_SET_IER(uart, ERBFI);
 654         return 0;
 655 }
 656
 657 static void bfin_serial_shutdown(struct uart_port *port)
 658 {
 659         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 660
 661 #ifdef CONFIG_SERIAL_BFIN_DMA
 662         disable_dma(uart->tx_dma_channel);
 663         free_dma(uart->tx_dma_channel);
 664         disable_dma(uart->rx_dma_channel);
 665         free_dma(uart->rx_dma_channel);
 666         del_timer(&(uart->rx_dma_timer));
 667         dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0);
 668 #else
 669 #ifdef  CONFIG_KGDB_UART
 670         if (uart->port.line != CONFIG_KGDB_UART_PORT)
 671 #endif
 672         free_irq(uart->port.irq, uart);
 673         free_irq(uart->port.irq+1, uart);
 674 #endif
 675 }
 676
 677 static void
 678 bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
 679                    struct ktermios *old)
 680 {
 681         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 682         unsigned long flags;
 683         unsigned int baud, quot;
 684         unsigned short val, ier, lcr = 0;
 685
 686         switch (termios->c_cflag & CSIZE) {
 687         case CS8:
 688                 lcr = WLS(8);
 689                 break;
 690         case CS7:
 691                 lcr = WLS(7);
 692                 break;
 693         case CS6:
 694                 lcr = WLS(6);
 695                 break;
 696         case CS5:
 697                 lcr = WLS(5);
 698                 break;
 699         default:
 700                 printk(KERN_ERR "%s: word lengh not supported\n",
 701                         __func__);
 702         }
 703
 704         if (termios->c_cflag & CSTOPB)
 705                 lcr |= STB;
 706         if (termios->c_cflag & PARENB)
 707                 lcr |= PEN;
 708         if (!(termios->c_cflag & PARODD))
 709                 lcr |= EPS;
 710         if (termios->c_cflag & CMSPAR)
 711                 lcr |= STP;
 712
 713         port->read_status_mask = OE;
 714         if (termios->c_iflag & INPCK)
 715                 port->read_status_mask |= (FE | PE);
 716         if (termios->c_iflag & (BRKINT | PARMRK))
 717                 port->read_status_mask |= BI;
 718
 719         /*
 720          * Characters to ignore
 721          */
 722         port->ignore_status_mask = 0;
 723         if (termios->c_iflag & IGNPAR)
 724                 port->ignore_status_mask |= FE | PE;
 725         if (termios->c_iflag & IGNBRK) {
 726                 port->ignore_status_mask |= BI;
 727                 /*
 728                  * If we're ignoring parity and break indicators,
 729                  * ignore overruns too (for real raw support).
 730                  */
 731                 if (termios->c_iflag & IGNPAR)
 732                         port->ignore_status_mask |= OE;
 733         }
 734
 735         baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
 736         quot = uart_get_divisor(port, baud);
 737         spin_lock_irqsave(&uart->port.lock, flags);
 738
 739         UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
 740
 741         /* Disable UART */
 742         ier = UART_GET_IER(uart);
 743         UART_DISABLE_INTS(uart);
 744
 745         /* Set DLAB in LCR to Access DLL and DLH */
 746         UART_SET_DLAB(uart);
 747
 748         UART_PUT_DLL(uart, quot & 0xFF);
 749         UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
 750         SSYNC();
 751
 752         /* Clear DLAB in LCR to Access THR RBR IER */
 753         UART_CLEAR_DLAB(uart);
 754
 755         UART_PUT_LCR(uart, lcr);
 756
 757         /* Enable UART */
 758         UART_ENABLE_INTS(uart, ier);
 759
 760         val = UART_GET_GCTL(uart);
 761         val |= UCEN;
 762         UART_PUT_GCTL(uart, val);
 763
 764         /* Port speed changed, update the per-port timeout. */
 765         uart_update_timeout(port, termios->c_cflag, baud);
 766
 767         spin_unlock_irqrestore(&uart->port.lock, flags);
 768 }
 769
 770 static const char *bfin_serial_type(struct uart_port *port)
 771 {
 772         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 773
 774         return uart->port.type == PORT_BFIN ? "BFIN-UART" : NULL;
 775 }
 776
 777 /*
 778  * Release the memory region(s) being used by 'port'.
 779  */
 780 static void bfin_serial_release_port(struct uart_port *port)
 781 {
 782 }
 783
 784 /*
 785  * Request the memory region(s) being used by 'port'.
 786  */
 787 static int bfin_serial_request_port(struct uart_port *port)
 788 {
 789         return 0;
 790 }
 791
 792 /*
 793  * Configure/autoconfigure the port.
 794  */
 795 static void bfin_serial_config_port(struct uart_port *port, int flags)
 796 {
 797         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 798
 799         if (flags & UART_CONFIG_TYPE &&
 800             bfin_serial_request_port(&uart->port) == 0)
 801                 uart->port.type = PORT_BFIN;
 802 }
 803
 804 /*
 805  * Verify the new serial_struct (for TIOCSSERIAL).
 806  * The only change we allow are to the flags and type, and
 807  * even then only between PORT_BFIN and PORT_UNKNOWN
 808  */
 809 static int
 810 bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
 811 {
 812         return 0;
 813 }
 814
 815 /*
 816  * Enable the IrDA function if tty->ldisc.num is N_IRDA.
 817  * In other cases, disable IrDA function.
 818  */
 819 static void bfin_serial_set_ldisc(struct uart_port *port)
 820 {
 821         int line = port->line;
 822         unsigned short val;
 823
 824         if (line >= port->info->port.tty->driver->num)
 825                 return;
 826
 827         switch (port->info->port.tty->termios->c_line) {
 828         case N_IRDA:
 829                 val = UART_GET_GCTL(&bfin_serial_ports[line]);
 830                 val |= (IREN | RPOLC);
 831                 UART_PUT_GCTL(&bfin_serial_ports[line], val);
 832                 break;
 833         default:
 834                 val = UART_GET_GCTL(&bfin_serial_ports[line]);
 835                 val &= ~(IREN | RPOLC);
 836                 UART_PUT_GCTL(&bfin_serial_ports[line], val);
 837         }
 838 }
 839
 840 static struct uart_ops bfin_serial_pops = {
 841         .tx_empty       = bfin_serial_tx_empty,
 842         .set_mctrl      = bfin_serial_set_mctrl,
 843         .get_mctrl      = bfin_serial_get_mctrl,
 844         .stop_tx        = bfin_serial_stop_tx,
 845         .start_tx       = bfin_serial_start_tx,
 846         .stop_rx        = bfin_serial_stop_rx,
 847         .enable_ms      = bfin_serial_enable_ms,
 848         .break_ctl      = bfin_serial_break_ctl,
 849         .startup        = bfin_serial_startup,
 850         .shutdown       = bfin_serial_shutdown,
 851         .set_termios    = bfin_serial_set_termios,
 852         .set_ldisc      = bfin_serial_set_ldisc,
 853         .type           = bfin_serial_type,
 854         .release_port   = bfin_serial_release_port,
 855         .request_port   = bfin_serial_request_port,
 856         .config_port    = bfin_serial_config_port,
 857         .verify_port    = bfin_serial_verify_port,
 858 };
 859
 860 static void __init bfin_serial_init_ports(void)
 861 {
 862         static int first = 1;
 863         int i;
 864
 865         if (!first)
 866                 return;
 867         first = 0;
 868
 869         for (i = 0; i < nr_active_ports; i++) {
 870                 bfin_serial_ports[i].port.uartclk   = get_sclk();
 871                 bfin_serial_ports[i].port.fifosize  = BFIN_UART_TX_FIFO_SIZE;
 872                 bfin_serial_ports[i].port.ops       = &bfin_serial_pops;
 873                 bfin_serial_ports[i].port.line      = i;
 874                 bfin_serial_ports[i].port.iotype    = UPIO_MEM;
 875                 bfin_serial_ports[i].port.membase   =
 876                         (void __iomem *)bfin_serial_resource[i].uart_base_addr;
 877                 bfin_serial_ports[i].port.mapbase   =
 878                         bfin_serial_resource[i].uart_base_addr;
 879                 bfin_serial_ports[i].port.irq       =
 880                         bfin_serial_resource[i].uart_irq;
 881                 bfin_serial_ports[i].port.flags     = UPF_BOOT_AUTOCONF;
 882 #ifdef CONFIG_SERIAL_BFIN_DMA
 883                 bfin_serial_ports[i].tx_done        = 1;
 884                 bfin_serial_ports[i].tx_count       = 0;
 885                 bfin_serial_ports[i].tx_dma_channel =
 886                         bfin_serial_resource[i].uart_tx_dma_channel;
 887                 bfin_serial_ports[i].rx_dma_channel =
 888                         bfin_serial_resource[i].uart_rx_dma_channel;
 889                 init_timer(&(bfin_serial_ports[i].rx_dma_timer));
 890 #endif
 891 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
 892                 init_timer(&(bfin_serial_ports[i].cts_timer));
 893                 bfin_serial_ports[i].cts_pin        =
 894                         bfin_serial_resource[i].uart_cts_pin;
 895                 bfin_serial_ports[i].rts_pin        =
 896                         bfin_serial_resource[i].uart_rts_pin;
 897 #endif
 898                 bfin_serial_hw_init(&bfin_serial_ports[i]);
 899         }
 900
 901 }
 902
 903 #ifdef CONFIG_SERIAL_BFIN_CONSOLE
 904 /*
 905  * If the port was already initialised (eg, by a boot loader),
 906  * try to determine the current setup.
 907  */
 908 static void __init
 909 bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
 910                            int *parity, int *bits)
 911 {
 912         unsigned short status;
 913
 914         status = UART_GET_IER(uart) & (ERBFI | ETBEI);
 915         if (status == (ERBFI | ETBEI)) {
 916                 /* ok, the port was enabled */
 917                 u16 lcr, dlh, dll;
 918
 919                 lcr = UART_GET_LCR(uart);
 920
 921                 *parity = 'n';
 922                 if (lcr & PEN) {
 923                         if (lcr & EPS)
 924                                 *parity = 'e';
 925                         else
 926                                 *parity = 'o';
 927                 }
 928                 switch (lcr & 0x03) {
 929                         case 0: *bits = 5; break;
 930                         case 1: *bits = 6; break;
 931                         case 2: *bits = 7; break;
 932                         case 3: *bits = 8; break;
 933                 }
 934                 /* Set DLAB in LCR to Access DLL and DLH */
 935                 UART_SET_DLAB(uart);
 936
 937                 dll = UART_GET_DLL(uart);
 938                 dlh = UART_GET_DLH(uart);
 939
 940                 /* Clear DLAB in LCR to Access THR RBR IER */
 941                 UART_CLEAR_DLAB(uart);
 942
 943                 *baud = get_sclk() / (16*(dll | dlh << 8));
 944         }
 945         pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits);
 946 }
 947 #endif
 948
 949 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
 950 static struct uart_driver bfin_serial_reg;
 951
 952 static int __init
 953 bfin_serial_console_setup(struct console *co, char *options)
 954 {
 955         struct bfin_serial_port *uart;
 956 # ifdef CONFIG_SERIAL_BFIN_CONSOLE
 957         int baud = 57600;
 958         int bits = 8;
 959         int parity = 'n';
 960 #  ifdef CONFIG_SERIAL_BFIN_CTSRTS
 961         int flow = 'r';
 962 #  else
 963         int flow = 'n';
 964 #  endif
 965 # endif
 966
 967         /*
 968          * Check whether an invalid uart number has been specified, and
 969          * if so, search for the first available port that does have
 970          * console support.
 971          */
 972         if (co->index == -1 || co->index >= nr_active_ports)
 973                 co->index = 0;
 974         uart = &bfin_serial_ports[co->index];
 975
 976 # ifdef CONFIG_SERIAL_BFIN_CONSOLE
 977         if (options)
 978                 uart_parse_options(options, &baud, &parity, &bits, &flow);
 979         else
 980                 bfin_serial_console_get_options(uart, &baud, &parity, &bits);
 981
 982         return uart_set_options(&uart->port, co, baud, parity, bits, flow);
 983 # else
 984         return 0;
 985 # endif
 986 }
 987 #endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
 988                                  defined (CONFIG_EARLY_PRINTK) */
 989
 990 #ifdef CONFIG_SERIAL_BFIN_CONSOLE
 991 static void bfin_serial_console_putchar(struct uart_port *port, int ch)
 992 {
 993         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 994         while (!(UART_GET_LSR(uart) & THRE))
 995                 barrier();
 996         UART_PUT_CHAR(uart, ch);
 997         SSYNC();
 998 }
 999
1000 /*
1001  * Interrupts are disabled on entering
1002  */
1003 static void
1004 bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
1005 {
1006         struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
1007         int flags = 0;
1008
1009         spin_lock_irqsave(&uart->port.lock, flags);
1010         uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
1011         spin_unlock_irqrestore(&uart->port.lock, flags);
1012
1013 }
1014
1015 static struct console bfin_serial_console = {
1016         .name           = BFIN_SERIAL_NAME,
1017         .write          = bfin_serial_console_write,
1018         .device         = uart_console_device,
1019         .setup          = bfin_serial_console_setup,
1020         .flags          = CON_PRINTBUFFER,
1021         .index          = -1,
1022         .data           = &bfin_serial_reg,
1023 };
1024
1025 static int __init bfin_serial_rs_console_init(void)
1026 {
1027         bfin_serial_init_ports();
1028         register_console(&bfin_serial_console);
1029 #ifdef CONFIG_KGDB_UART
1030         kgdb_entry_state = 0;
1031         init_kgdb_uart();
1032 #endif
1033         return 0;
1034 }
1035 console_initcall(bfin_serial_rs_console_init);
1036
1037 #define BFIN_SERIAL_CONSOLE     &bfin_serial_console
1038 #else
1039 #define BFIN_SERIAL_CONSOLE     NULL
1040 #endif /* CONFIG_SERIAL_BFIN_CONSOLE */
1041
1042
1043 #ifdef CONFIG_EARLY_PRINTK
1044 static __init void early_serial_putc(struct uart_port *port, int ch)
1045 {
1046         unsigned timeout = 0xffff;
1047         struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1048
1049         while ((!(UART_GET_LSR(uart) & THRE)) && --timeout)
1050                 cpu_relax();
1051         UART_PUT_CHAR(uart, ch);
1052 }
1053
1054 static __init void early_serial_write(struct console *con, const char *s,
1055                                         unsigned int n)
1056 {
1057         struct bfin_serial_port *uart = &bfin_serial_ports[con->index];
1058         unsigned int i;
1059
1060         for (i = 0; i < n; i++, s++) {
1061                 if (*s == '\n')
1062                         early_serial_putc(&uart->port, '\r');
1063                 early_serial_putc(&uart->port, *s);
1064         }
1065 }
1066
1067 static struct __initdata console bfin_early_serial_console = {
1068         .name = "early_BFuart",
1069         .write = early_serial_write,
1070         .device = uart_console_device,
1071         .flags = CON_PRINTBUFFER,
1072         .setup = bfin_serial_console_setup,
1073         .index = -1,
1074         .data  = &bfin_serial_reg,
1075 };
1076
1077 struct console __init *bfin_earlyserial_init(unsigned int port,
1078                                                 unsigned int cflag)
1079 {
1080         struct bfin_serial_port *uart;
1081         struct ktermios t;
1082
1083         if (port == -1 || port >= nr_active_ports)
1084                 port = 0;
1085         bfin_serial_init_ports();
1086         bfin_early_serial_console.index = port;
1087         uart = &bfin_serial_ports[port];
1088         t.c_cflag = cflag;
1089         t.c_iflag = 0;
1090         t.c_oflag = 0;
1091         t.c_lflag = ICANON;
1092         t.c_line = port;
1093         bfin_serial_set_termios(&uart->port, &t, &t);
1094         return &bfin_early_serial_console;
1095 }
1096
1097 #endif /* CONFIG_SERIAL_BFIN_CONSOLE */
1098
1099 static struct uart_driver bfin_serial_reg = {
1100         .owner                  = THIS_MODULE,
1101         .driver_name            = "bfin-uart",
1102         .dev_name               = BFIN_SERIAL_NAME,
1103         .major                  = BFIN_SERIAL_MAJOR,
1104         .minor                  = BFIN_SERIAL_MINOR,
1105         .nr                     = BFIN_UART_NR_PORTS,
1106         .cons                   = BFIN_SERIAL_CONSOLE,
1107 };
1108
1109 static int bfin_serial_suspend(struct platform_device *dev, pm_message_t state)
1110 {
1111         int i;
1112
1113         for (i = 0; i < nr_active_ports; i++) {
1114                 if (bfin_serial_ports[i].port.dev != &dev->dev)
1115                         continue;
1116                 uart_suspend_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1117         }
1118
1119         return 0;
1120 }
1121
1122 static int bfin_serial_resume(struct platform_device *dev)
1123 {
1124         int i;
1125
1126         for (i = 0; i < nr_active_ports; i++) {
1127                 if (bfin_serial_ports[i].port.dev != &dev->dev)
1128                         continue;
1129                 uart_resume_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1130         }
1131
1132         return 0;
1133 }
1134
1135 static int bfin_serial_probe(struct platform_device *dev)
1136 {
1137         struct resource *res = dev->resource;
1138         int i;
1139
1140         for (i = 0; i < dev->num_resources; i++, res++)
1141                 if (res->flags & IORESOURCE_MEM)
1142                         break;
1143
1144         if (i < dev->num_resources) {
1145                 for (i = 0; i < nr_active_ports; i++, res++) {
1146                         if (bfin_serial_ports[i].port.mapbase != res->start)
1147                                 continue;
1148                         bfin_serial_ports[i].port.dev = &dev->dev;
1149                         uart_add_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1150                 }
1151         }
1152
1153         return 0;
1154 }
1155
1156 static int bfin_serial_remove(struct platform_device *dev)
1157 {
1158         int i;
1159
1160         for (i = 0; i < nr_active_ports; i++) {
1161                 if (bfin_serial_ports[i].port.dev != &dev->dev)
1162                         continue;
1163                 uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1164                 bfin_serial_ports[i].port.dev = NULL;
1165 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
1166                 gpio_free(bfin_serial_ports[i].cts_pin);
1167                 gpio_free(bfin_serial_ports[i].rts_pin);
1168 #endif
1169         }
1170
1171         return 0;
1172 }
1173
1174 static struct platform_driver bfin_serial_driver = {
1175         .probe          = bfin_serial_probe,
1176         .remove         = bfin_serial_remove,
1177         .suspend        = bfin_serial_suspend,
1178         .resume         = bfin_serial_resume,
1179         .driver         = {
1180                 .name   = "bfin-uart",
1181                 .owner  = THIS_MODULE,
1182         },
1183 };
1184
1185 static int __init bfin_serial_init(void)
1186 {
1187         int ret;
1188 #ifdef CONFIG_KGDB_UART
1189         struct bfin_serial_port *uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
1190         struct ktermios t;
1191 #endif
1192
1193         pr_info("Serial: Blackfin serial driver\n");
1194
1195         bfin_serial_init_ports();
1196
1197         ret = uart_register_driver(&bfin_serial_reg);
1198         if (ret == 0) {
1199                 ret = platform_driver_register(&bfin_serial_driver);
1200                 if (ret) {
1201                         pr_debug("uart register failed\n");
1202                         uart_unregister_driver(&bfin_serial_reg);
1203                 }
1204         }
1205 #ifdef CONFIG_KGDB_UART
1206         if (uart->port.cons->index != CONFIG_KGDB_UART_PORT) {
1207                 request_irq(uart->port.irq, bfin_serial_rx_int,
1208                         IRQF_DISABLED, "BFIN_UART_RX", uart);
1209                 pr_info("Request irq for kgdb uart port\n");
1210                 UART_SET_IER(uart, ERBFI);
1211                 SSYNC();
1212                 t.c_cflag = CS8|B57600;
1213                 t.c_iflag = 0;
1214                 t.c_oflag = 0;
1215                 t.c_lflag = ICANON;
1216                 t.c_line = CONFIG_KGDB_UART_PORT;
1217                 bfin_serial_set_termios(&uart->port, &t, &t);
1218         }
1219 #endif
1220         return ret;
1221 }
1222
1223 static void __exit bfin_serial_exit(void)
1224 {
1225         platform_driver_unregister(&bfin_serial_driver);
1226         uart_unregister_driver(&bfin_serial_reg);
1227 }
1228
1229 module_init(bfin_serial_init);
1230 module_exit(bfin_serial_exit);
1231
1232 MODULE_AUTHOR("Aubrey.Li <aubrey.li@analog.com>");
1233 MODULE_DESCRIPTION("Blackfin generic serial port driver");
1234 MODULE_LICENSE("GPL");
1235 MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR);
1236 MODULE_ALIAS("platform:bfin-uart");