drivers/pinctrl/pinctrl-keembay.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /* Copyright (C) 2020 Intel Corporation */
   3
   4 #include <linux/bitfield.h>
   5 #include <linux/bitops.h>
   6 #include <linux/gpio/driver.h>
   7 #include <linux/interrupt.h>
   8 #include <linux/io.h>
   9 #include <linux/module.h>
  10
  11 #include <linux/pinctrl/pinconf.h>
  12 #include <linux/pinctrl/pinconf-generic.h>
  13 #include <linux/pinctrl/pinctrl.h>
  14 #include <linux/pinctrl/pinmux.h>
  15
  16 #include <linux/platform_device.h>
  17
  18 #include "core.h"
  19 #include "pinmux.h"
  20
  21 /* GPIO data registers' offsets */
  22 #define KEEMBAY_GPIO_DATA_OUT           0x000
  23 #define KEEMBAY_GPIO_DATA_IN            0x020
  24 #define KEEMBAY_GPIO_DATA_IN_RAW        0x040
  25 #define KEEMBAY_GPIO_DATA_HIGH          0x060
  26 #define KEEMBAY_GPIO_DATA_LOW           0x080
  27
  28 /* GPIO Interrupt and mode registers' offsets */
  29 #define KEEMBAY_GPIO_INT_CFG            0x000
  30 #define KEEMBAY_GPIO_MODE               0x070
  31
  32 /* GPIO mode register bit fields */
  33 #define KEEMBAY_GPIO_MODE_PULLUP_MASK   GENMASK(13, 12)
  34 #define KEEMBAY_GPIO_MODE_DRIVE_MASK    GENMASK(8, 7)
  35 #define KEEMBAY_GPIO_MODE_INV_MASK      GENMASK(5, 4)
  36 #define KEEMBAY_GPIO_MODE_SELECT_MASK   GENMASK(2, 0)
  37 #define KEEMBAY_GPIO_MODE_DIR_OVR       BIT(15)
  38 #define KEEMBAY_GPIO_MODE_REN           BIT(11)
  39 #define KEEMBAY_GPIO_MODE_SCHMITT_EN    BIT(10)
  40 #define KEEMBAY_GPIO_MODE_SLEW_RATE     BIT(9)
  41 #define KEEMBAY_GPIO_IRQ_ENABLE         BIT(7)
  42 #define KEEMBAY_GPIO_MODE_DIR           BIT(3)
  43 #define KEEMBAY_GPIO_MODE_DEFAULT       0x7
  44 #define KEEMBAY_GPIO_MODE_INV_VAL       0x3
  45
  46 #define KEEMBAY_GPIO_DISABLE            0
  47 #define KEEMBAY_GPIO_PULL_UP            1
  48 #define KEEMBAY_GPIO_PULL_DOWN          2
  49 #define KEEMBAY_GPIO_BUS_HOLD           3
  50 #define KEEMBAY_GPIO_NUM_IRQ            8
  51 #define KEEMBAY_GPIO_MAX_PER_IRQ        4
  52 #define KEEMBAY_GPIO_MAX_PER_REG        32
  53 #define KEEMBAY_GPIO_MIN_STRENGTH       2
  54 #define KEEMBAY_GPIO_MAX_STRENGTH       12
  55 #define KEEMBAY_GPIO_SENSE_LOW          (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_EDGE_FALLING)
  56
  57 /* GPIO reg address calculation */
  58 #define KEEMBAY_GPIO_REG_OFFSET(pin)    ((pin) * 4)
  59
  60 /**
  61  * struct keembay_mux_desc - Mux properties of each GPIO pin
  62  * @mode: Pin mode when operating in this function
  63  * @name: Pin function name
  64  */
  65 struct keembay_mux_desc {
  66         u8 mode;
  67         const char *name;
  68 };
  69
  70 #define KEEMBAY_PIN_DESC(pin_number, pin_name, ...) {   \
  71         .number = pin_number,                           \
  72         .name = pin_name,                               \
  73         .drv_data = &(struct keembay_mux_desc[]) {      \
  74                     __VA_ARGS__, { } },                 \
  75 }                                                       \
  76
  77 #define KEEMBAY_MUX(pin_mode, pin_function) {           \
  78         .mode = pin_mode,                               \
  79         .name = pin_function,                           \
  80 }                                                       \
  81
  82 /**
  83  * struct keembay_gpio_irq - Config of each GPIO Interrupt sources
  84  * @source: Interrupt source number (0 - 7)
  85  * @line: Actual Interrupt line number
  86  * @pins: Array of GPIO pins using this Interrupt line
  87  * @trigger: Interrupt trigger type for this line
  88  * @num_share: Number of pins currently using this Interrupt line
  89  */
  90 struct keembay_gpio_irq {
  91         unsigned int source;
  92         unsigned int line;
  93         unsigned int pins[KEEMBAY_GPIO_MAX_PER_IRQ];
  94         unsigned int trigger;
  95         unsigned int num_share;
  96 };
  97
  98 /**
  99  * struct keembay_pinctrl - Intel Keembay pinctrl structure
 100  * @pctrl: Pointer to the pin controller device
 101  * @base0: First register base address
 102  * @base1: Second register base address
 103  * @dev: Pointer to the device structure
 104  * @chip: GPIO chip used by this pin controller
 105  * @soc: Pin control configuration data based on SoC
 106  * @lock: Spinlock to protect various gpio config register access
 107  * @ngroups: Number of pin groups available
 108  * @nfuncs: Number of pin functions available
 109  * @npins: Number of GPIO pins available
 110  * @irq: Store Interrupt source
 111  * @max_gpios_level_type: Store max level trigger type
 112  * @max_gpios_edge_type: Store max edge trigger type
 113  */
 114 struct keembay_pinctrl {
 115         struct pinctrl_dev *pctrl;
 116         void __iomem *base0;
 117         void __iomem *base1;
 118         struct device *dev;
 119         struct gpio_chip chip;
 120         const struct keembay_pin_soc *soc;
 121         raw_spinlock_t lock;
 122         unsigned int ngroups;
 123         unsigned int nfuncs;
 124         unsigned int npins;
 125         struct keembay_gpio_irq irq[KEEMBAY_GPIO_NUM_IRQ];
 126         int max_gpios_level_type;
 127         int max_gpios_edge_type;
 128 };
 129
 130 /**
 131  * struct keembay_pin_soc - Pin control config data based on SoC
 132  * @pins: Pin description structure
 133  */
 134 struct keembay_pin_soc {
 135         const struct pinctrl_pin_desc *pins;
 136 };
 137
 138 static const struct pinctrl_pin_desc keembay_pins[] = {
 139         KEEMBAY_PIN_DESC(0, "GPIO0",
 140                          KEEMBAY_MUX(0x0, "I2S0_M0"),
 141                          KEEMBAY_MUX(0x1, "SD0_M1"),
 142                          KEEMBAY_MUX(0x2, "SLVDS0_M2"),
 143                          KEEMBAY_MUX(0x3, "I2C0_M3"),
 144                          KEEMBAY_MUX(0x4, "CAM_M4"),
 145                          KEEMBAY_MUX(0x5, "ETH_M5"),
 146                          KEEMBAY_MUX(0x6, "LCD_M6"),
 147                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 148         KEEMBAY_PIN_DESC(1, "GPIO1",
 149                          KEEMBAY_MUX(0x0, "I2S0_M0"),
 150                          KEEMBAY_MUX(0x1, "SD0_M1"),
 151                          KEEMBAY_MUX(0x2, "SLVDS0_M2"),
 152                          KEEMBAY_MUX(0x3, "I2C0_M3"),
 153                          KEEMBAY_MUX(0x4, "CAM_M4"),
 154                          KEEMBAY_MUX(0x5, "ETH_M5"),
 155                          KEEMBAY_MUX(0x6, "LCD_M6"),
 156                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 157         KEEMBAY_PIN_DESC(2, "GPIO2",
 158                          KEEMBAY_MUX(0x0, "I2S0_M0"),
 159                          KEEMBAY_MUX(0x1, "I2S0_M1"),
 160                          KEEMBAY_MUX(0x2, "SLVDS0_M2"),
 161                          KEEMBAY_MUX(0x3, "I2C1_M3"),
 162                          KEEMBAY_MUX(0x4, "CAM_M4"),
 163                          KEEMBAY_MUX(0x5, "ETH_M5"),
 164                          KEEMBAY_MUX(0x6, "LCD_M6"),
 165                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 166         KEEMBAY_PIN_DESC(3, "GPIO3",
 167                          KEEMBAY_MUX(0x0, "I2S0_M0"),
 168                          KEEMBAY_MUX(0x1, "I2S0_M1"),
 169                          KEEMBAY_MUX(0x2, "SLVDS0_M2"),
 170                          KEEMBAY_MUX(0x3, "I2C1_M3"),
 171                          KEEMBAY_MUX(0x4, "CAM_M4"),
 172                          KEEMBAY_MUX(0x5, "ETH_M5"),
 173                          KEEMBAY_MUX(0x6, "LCD_M6"),
 174                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 175         KEEMBAY_PIN_DESC(4, "GPIO4",
 176                          KEEMBAY_MUX(0x0, "I2S0_M0"),
 177                          KEEMBAY_MUX(0x1, "I2S0_M1"),
 178                          KEEMBAY_MUX(0x2, "SLVDS0_M2"),
 179                          KEEMBAY_MUX(0x3, "I2C2_M3"),
 180                          KEEMBAY_MUX(0x4, "CAM_M4"),
 181                          KEEMBAY_MUX(0x5, "ETH_M5"),
 182                          KEEMBAY_MUX(0x6, "LCD_M6"),
 183                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 184         KEEMBAY_PIN_DESC(5, "GPIO5",
 185                          KEEMBAY_MUX(0x0, "I2S0_M0"),
 186                          KEEMBAY_MUX(0x1, "I2S0_M1"),
 187                          KEEMBAY_MUX(0x2, "SLVDS0_M2"),
 188                          KEEMBAY_MUX(0x3, "I2C2_M3"),
 189                          KEEMBAY_MUX(0x4, "CAM_M4"),
 190                          KEEMBAY_MUX(0x5, "ETH_M5"),
 191                          KEEMBAY_MUX(0x6, "LCD_M6"),
 192                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 193         KEEMBAY_PIN_DESC(6, "GPIO6",
 194                          KEEMBAY_MUX(0x0, "I2S1_M0"),
 195                          KEEMBAY_MUX(0x1, "SD0_M1"),
 196                          KEEMBAY_MUX(0x2, "SLVDS0_M2"),
 197                          KEEMBAY_MUX(0x3, "I2C3_M3"),
 198                          KEEMBAY_MUX(0x4, "CAM_M4"),
 199                          KEEMBAY_MUX(0x5, "ETH_M5"),
 200                          KEEMBAY_MUX(0x6, "LCD_M6"),
 201                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 202         KEEMBAY_PIN_DESC(7, "GPIO7",
 203                          KEEMBAY_MUX(0x0, "I2S1_M0"),
 204                          KEEMBAY_MUX(0x1, "SD0_M1"),
 205                          KEEMBAY_MUX(0x2, "SLVDS0_M2"),
 206                          KEEMBAY_MUX(0x3, "I2C3_M3"),
 207                          KEEMBAY_MUX(0x4, "CAM_M4"),
 208                          KEEMBAY_MUX(0x5, "ETH_M5"),
 209                          KEEMBAY_MUX(0x6, "LCD_M6"),
 210                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 211         KEEMBAY_PIN_DESC(8, "GPIO8",
 212                          KEEMBAY_MUX(0x0, "I2S1_M0"),
 213                          KEEMBAY_MUX(0x1, "I2S1_M1"),
 214                          KEEMBAY_MUX(0x2, "SLVDS0_M2"),
 215                          KEEMBAY_MUX(0x3, "UART0_M3"),
 216                          KEEMBAY_MUX(0x4, "CAM_M4"),
 217                          KEEMBAY_MUX(0x5, "ETH_M5"),
 218                          KEEMBAY_MUX(0x6, "LCD_M6"),
 219                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 220         KEEMBAY_PIN_DESC(9, "GPIO9",
 221                          KEEMBAY_MUX(0x0, "I2S1_M0"),
 222                          KEEMBAY_MUX(0x1, "I2S1_M1"),
 223                          KEEMBAY_MUX(0x2, "PWM_M2"),
 224                          KEEMBAY_MUX(0x3, "UART0_M3"),
 225                          KEEMBAY_MUX(0x4, "CAM_M4"),
 226                          KEEMBAY_MUX(0x5, "ETH_M5"),
 227                          KEEMBAY_MUX(0x6, "LCD_M6"),
 228                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 229         KEEMBAY_PIN_DESC(10, "GPIO10",
 230                          KEEMBAY_MUX(0x0, "I2S2_M0"),
 231                          KEEMBAY_MUX(0x1, "SD0_M1"),
 232                          KEEMBAY_MUX(0x2, "PWM_M2"),
 233                          KEEMBAY_MUX(0x3, "UART0_M3"),
 234                          KEEMBAY_MUX(0x4, "CAM_M4"),
 235                          KEEMBAY_MUX(0x5, "ETH_M5"),
 236                          KEEMBAY_MUX(0x6, "LCD_M6"),
 237                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 238         KEEMBAY_PIN_DESC(11, "GPIO11",
 239                          KEEMBAY_MUX(0x0, "I2S2_M0"),
 240                          KEEMBAY_MUX(0x1, "SD0_M1"),
 241                          KEEMBAY_MUX(0x2, "PWM_M2"),
 242                          KEEMBAY_MUX(0x3, "UART0_M3"),
 243                          KEEMBAY_MUX(0x4, "CAM_M4"),
 244                          KEEMBAY_MUX(0x5, "ETH_M5"),
 245                          KEEMBAY_MUX(0x6, "LCD_M6"),
 246                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 247         KEEMBAY_PIN_DESC(12, "GPIO12",
 248                          KEEMBAY_MUX(0x0, "I2S2_M0"),
 249                          KEEMBAY_MUX(0x1, "I2S2_M1"),
 250                          KEEMBAY_MUX(0x2, "PWM_M2"),
 251                          KEEMBAY_MUX(0x3, "SPI0_M3"),
 252                          KEEMBAY_MUX(0x4, "CAM_M4"),
 253                          KEEMBAY_MUX(0x5, "ETH_M5"),
 254                          KEEMBAY_MUX(0x6, "LCD_M6"),
 255                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 256         KEEMBAY_PIN_DESC(13, "GPIO13",
 257                          KEEMBAY_MUX(0x0, "I2S2_M0"),
 258                          KEEMBAY_MUX(0x1, "I2S2_M1"),
 259                          KEEMBAY_MUX(0x2, "PWM_M2"),
 260                          KEEMBAY_MUX(0x3, "SPI0_M3"),
 261                          KEEMBAY_MUX(0x4, "CAM_M4"),
 262                          KEEMBAY_MUX(0x5, "ETH_M5"),
 263                          KEEMBAY_MUX(0x6, "LCD_M6"),
 264                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 265         KEEMBAY_PIN_DESC(14, "GPIO14",
 266                          KEEMBAY_MUX(0x0, "UART0_M0"),
 267                          KEEMBAY_MUX(0x1, "I2S3_M1"),
 268                          KEEMBAY_MUX(0x2, "PWM_M2"),
 269                          KEEMBAY_MUX(0x3, "SD1_M3"),
 270                          KEEMBAY_MUX(0x4, "CAM_M4"),
 271                          KEEMBAY_MUX(0x5, "ETH_M5"),
 272                          KEEMBAY_MUX(0x6, "LCD_M6"),
 273                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 274         KEEMBAY_PIN_DESC(15, "GPIO15",
 275                          KEEMBAY_MUX(0x0, "UART0_M0"),
 276                          KEEMBAY_MUX(0x1, "I2S3_M1"),
 277                          KEEMBAY_MUX(0x2, "UART0_M2"),
 278                          KEEMBAY_MUX(0x3, "SD1_M3"),
 279                          KEEMBAY_MUX(0x4, "CAM_M4"),
 280                          KEEMBAY_MUX(0x5, "SPI1_M5"),
 281                          KEEMBAY_MUX(0x6, "LCD_M6"),
 282                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 283         KEEMBAY_PIN_DESC(16, "GPIO16",
 284                          KEEMBAY_MUX(0x0, "UART0_M0"),
 285                          KEEMBAY_MUX(0x1, "I2S3_M1"),
 286                          KEEMBAY_MUX(0x2, "UART0_M2"),
 287                          KEEMBAY_MUX(0x3, "SD1_M3"),
 288                          KEEMBAY_MUX(0x4, "CAM_M4"),
 289                          KEEMBAY_MUX(0x5, "SPI1_M5"),
 290                          KEEMBAY_MUX(0x6, "LCD_M6"),
 291                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 292         KEEMBAY_PIN_DESC(17, "GPIO17",
 293                          KEEMBAY_MUX(0x0, "UART0_M0"),
 294                          KEEMBAY_MUX(0x1, "I2S3_M1"),
 295                          KEEMBAY_MUX(0x2, "I2S3_M2"),
 296                          KEEMBAY_MUX(0x3, "SD1_M3"),
 297                          KEEMBAY_MUX(0x4, "CAM_M4"),
 298                          KEEMBAY_MUX(0x5, "SPI1_M5"),
 299                          KEEMBAY_MUX(0x6, "LCD_M6"),
 300                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 301         KEEMBAY_PIN_DESC(18, "GPIO18",
 302                          KEEMBAY_MUX(0x0, "UART1_M0"),
 303                          KEEMBAY_MUX(0x1, "SPI0_M1"),
 304                          KEEMBAY_MUX(0x2, "I2S3_M2"),
 305                          KEEMBAY_MUX(0x3, "SD1_M3"),
 306                          KEEMBAY_MUX(0x4, "CAM_M4"),
 307                          KEEMBAY_MUX(0x5, "SPI1_M5"),
 308                          KEEMBAY_MUX(0x6, "LCD_M6"),
 309                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 310         KEEMBAY_PIN_DESC(19, "GPIO19",
 311                          KEEMBAY_MUX(0x0, "UART1_M0"),
 312                          KEEMBAY_MUX(0x1, "LCD_M1"),
 313                          KEEMBAY_MUX(0x2, "DEBUG_M2"),
 314                          KEEMBAY_MUX(0x3, "SD1_M3"),
 315                          KEEMBAY_MUX(0x4, "CAM_M4"),
 316                          KEEMBAY_MUX(0x5, "SPI1_M5"),
 317                          KEEMBAY_MUX(0x6, "LCD_M6"),
 318                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 319         KEEMBAY_PIN_DESC(20, "GPIO20",
 320                          KEEMBAY_MUX(0x0, "UART1_M0"),
 321                          KEEMBAY_MUX(0x1, "LCD_M1"),
 322                          KEEMBAY_MUX(0x2, "DEBUG_M2"),
 323                          KEEMBAY_MUX(0x3, "CPR_M3"),
 324                          KEEMBAY_MUX(0x4, "CAM_M4"),
 325                          KEEMBAY_MUX(0x5, "SPI1_M5"),
 326                          KEEMBAY_MUX(0x6, "SLVDS0_M6"),
 327                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 328         KEEMBAY_PIN_DESC(21, "GPIO21",
 329                          KEEMBAY_MUX(0x0, "UART1_M0"),
 330                          KEEMBAY_MUX(0x1, "LCD_M1"),
 331                          KEEMBAY_MUX(0x2, "DEBUG_M2"),
 332                          KEEMBAY_MUX(0x3, "CPR_M3"),
 333                          KEEMBAY_MUX(0x4, "CAM_M4"),
 334                          KEEMBAY_MUX(0x5, "I3C0_M5"),
 335                          KEEMBAY_MUX(0x6, "SLVDS0_M6"),
 336                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 337         KEEMBAY_PIN_DESC(22, "GPIO22",
 338                          KEEMBAY_MUX(0x0, "I2C0_M0"),
 339                          KEEMBAY_MUX(0x1, "UART2_M1"),
 340                          KEEMBAY_MUX(0x2, "DEBUG_M2"),
 341                          KEEMBAY_MUX(0x3, "CPR_M3"),
 342                          KEEMBAY_MUX(0x4, "CAM_M4"),
 343                          KEEMBAY_MUX(0x5, "I3C0_M5"),
 344                          KEEMBAY_MUX(0x6, "SLVDS0_M6"),
 345                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 346         KEEMBAY_PIN_DESC(23, "GPIO23",
 347                          KEEMBAY_MUX(0x0, "I2C0_M0"),
 348                          KEEMBAY_MUX(0x1, "UART2_M1"),
 349                          KEEMBAY_MUX(0x2, "DEBUG_M2"),
 350                          KEEMBAY_MUX(0x3, "CPR_M3"),
 351                          KEEMBAY_MUX(0x4, "CAM_M4"),
 352                          KEEMBAY_MUX(0x5, "I3C1_M5"),
 353                          KEEMBAY_MUX(0x6, "SLVDS0_M6"),
 354                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 355         KEEMBAY_PIN_DESC(24, "GPIO24",
 356                          KEEMBAY_MUX(0x0, "I2C1_M0"),
 357                          KEEMBAY_MUX(0x1, "UART2_M1"),
 358                          KEEMBAY_MUX(0x2, "DEBUG_M2"),
 359                          KEEMBAY_MUX(0x3, "CPR_M3"),
 360                          KEEMBAY_MUX(0x4, "CAM_M4"),
 361                          KEEMBAY_MUX(0x5, "I3C1_M5"),
 362                          KEEMBAY_MUX(0x6, "SLVDS0_M6"),
 363                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 364         KEEMBAY_PIN_DESC(25, "GPIO25",
 365                          KEEMBAY_MUX(0x0, "I2C1_M0"),
 366                          KEEMBAY_MUX(0x1, "UART2_M1"),
 367                          KEEMBAY_MUX(0x2, "SPI0_M2"),
 368                          KEEMBAY_MUX(0x3, "CPR_M3"),
 369                          KEEMBAY_MUX(0x4, "CAM_M4"),
 370                          KEEMBAY_MUX(0x5, "I3C2_M5"),
 371                          KEEMBAY_MUX(0x6, "SLVDS0_M6"),
 372                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 373         KEEMBAY_PIN_DESC(26, "GPIO26",
 374                          KEEMBAY_MUX(0x0, "SPI0_M0"),
 375                          KEEMBAY_MUX(0x1, "I2C2_M1"),
 376                          KEEMBAY_MUX(0x2, "UART0_M2"),
 377                          KEEMBAY_MUX(0x3, "DSU_M3"),
 378                          KEEMBAY_MUX(0x4, "CAM_M4"),
 379                          KEEMBAY_MUX(0x5, "I3C2_M5"),
 380                          KEEMBAY_MUX(0x6, "SLVDS0_M6"),
 381                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 382         KEEMBAY_PIN_DESC(27, "GPIO27",
 383                          KEEMBAY_MUX(0x0, "SPI0_M0"),
 384                          KEEMBAY_MUX(0x1, "I2C2_M1"),
 385                          KEEMBAY_MUX(0x2, "UART0_M2"),
 386                          KEEMBAY_MUX(0x3, "DSU_M3"),
 387                          KEEMBAY_MUX(0x4, "CAM_M4"),
 388                          KEEMBAY_MUX(0x5, "I3C0_M5"),
 389                          KEEMBAY_MUX(0x6, "SLVDS0_M6"),
 390                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 391         KEEMBAY_PIN_DESC(28, "GPIO28",
 392                          KEEMBAY_MUX(0x0, "SPI0_M0"),
 393                          KEEMBAY_MUX(0x1, "I2C3_M1"),
 394                          KEEMBAY_MUX(0x2, "UART0_M2"),
 395                          KEEMBAY_MUX(0x3, "PWM_M3"),
 396                          KEEMBAY_MUX(0x4, "CAM_M4"),
 397                          KEEMBAY_MUX(0x5, "I3C1_M5"),
 398                          KEEMBAY_MUX(0x6, "SLVDS0_M6"),
 399                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 400         KEEMBAY_PIN_DESC(29, "GPIO29",
 401                          KEEMBAY_MUX(0x0, "SPI0_M0"),
 402                          KEEMBAY_MUX(0x1, "I2C3_M1"),
 403                          KEEMBAY_MUX(0x2, "UART0_M2"),
 404                          KEEMBAY_MUX(0x3, "PWM_M3"),
 405                          KEEMBAY_MUX(0x4, "CAM_M4"),
 406                          KEEMBAY_MUX(0x5, "I3C2_M5"),
 407                          KEEMBAY_MUX(0x6, "SLVDS1_M6"),
 408                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 409         KEEMBAY_PIN_DESC(30, "GPIO30",
 410                          KEEMBAY_MUX(0x0, "SPI0_M0"),
 411                          KEEMBAY_MUX(0x1, "I2S0_M1"),
 412                          KEEMBAY_MUX(0x2, "I2C4_M2"),
 413                          KEEMBAY_MUX(0x3, "PWM_M3"),
 414                          KEEMBAY_MUX(0x4, "CAM_M4"),
 415                          KEEMBAY_MUX(0x5, "LCD_M5"),
 416                          KEEMBAY_MUX(0x6, "SLVDS1_M6"),
 417                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 418         KEEMBAY_PIN_DESC(31, "GPIO31",
 419                          KEEMBAY_MUX(0x0, "SPI0_M0"),
 420                          KEEMBAY_MUX(0x1, "I2S0_M1"),
 421                          KEEMBAY_MUX(0x2, "I2C4_M2"),
 422                          KEEMBAY_MUX(0x3, "PWM_M3"),
 423                          KEEMBAY_MUX(0x4, "CAM_M4"),
 424                          KEEMBAY_MUX(0x5, "UART1_M5"),
 425                          KEEMBAY_MUX(0x6, "SLVDS1_M6"),
 426                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 427         KEEMBAY_PIN_DESC(32, "GPIO32",
 428                          KEEMBAY_MUX(0x0, "SD0_M0"),
 429                          KEEMBAY_MUX(0x1, "SPI0_M1"),
 430                          KEEMBAY_MUX(0x2, "UART1_M2"),
 431                          KEEMBAY_MUX(0x3, "PWM_M3"),
 432                          KEEMBAY_MUX(0x4, "CAM_M4"),
 433                          KEEMBAY_MUX(0x5, "PCIE_M5"),
 434                          KEEMBAY_MUX(0x6, "SLVDS1_M6"),
 435                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 436         KEEMBAY_PIN_DESC(33, "GPIO33",
 437                          KEEMBAY_MUX(0x0, "SD0_M0"),
 438                          KEEMBAY_MUX(0x1, "SPI0_M1"),
 439                          KEEMBAY_MUX(0x2, "UART1_M2"),
 440                          KEEMBAY_MUX(0x3, "PWM_M3"),
 441                          KEEMBAY_MUX(0x4, "CAM_M4"),
 442                          KEEMBAY_MUX(0x5, "PCIE_M5"),
 443                          KEEMBAY_MUX(0x6, "SLVDS1_M6"),
 444                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 445         KEEMBAY_PIN_DESC(34, "GPIO34",
 446                          KEEMBAY_MUX(0x0, "SD0_M0"),
 447                          KEEMBAY_MUX(0x1, "SPI0_M1"),
 448                          KEEMBAY_MUX(0x2, "I2C0_M2"),
 449                          KEEMBAY_MUX(0x3, "UART1_M3"),
 450                          KEEMBAY_MUX(0x4, "CAM_M4"),
 451                          KEEMBAY_MUX(0x5, "I2S0_M5"),
 452                          KEEMBAY_MUX(0x6, "SLVDS1_M6"),
 453                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 454         KEEMBAY_PIN_DESC(35, "GPIO35",
 455                          KEEMBAY_MUX(0x0, "SD0_M0"),
 456                          KEEMBAY_MUX(0x1, "PCIE_M1"),
 457                          KEEMBAY_MUX(0x2, "I2C0_M2"),
 458                          KEEMBAY_MUX(0x3, "UART1_M3"),
 459                          KEEMBAY_MUX(0x4, "CAM_M4"),
 460                          KEEMBAY_MUX(0x5, "I2S0_M5"),
 461                          KEEMBAY_MUX(0x6, "SLVDS1_M6"),
 462                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 463         KEEMBAY_PIN_DESC(36, "GPIO36",
 464                          KEEMBAY_MUX(0x0, "SD0_M0"),
 465                          KEEMBAY_MUX(0x1, "SPI3_M1"),
 466                          KEEMBAY_MUX(0x2, "I2C1_M2"),
 467                          KEEMBAY_MUX(0x3, "DEBUG_M3"),
 468                          KEEMBAY_MUX(0x4, "CAM_M4"),
 469                          KEEMBAY_MUX(0x5, "I2S0_M5"),
 470                          KEEMBAY_MUX(0x6, "SLVDS1_M6"),
 471                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 472         KEEMBAY_PIN_DESC(37, "GPIO37",
 473                          KEEMBAY_MUX(0x0, "SD0_M0"),
 474                          KEEMBAY_MUX(0x1, "SPI3_M1"),
 475                          KEEMBAY_MUX(0x2, "I2C1_M2"),
 476                          KEEMBAY_MUX(0x3, "DEBUG_M3"),
 477                          KEEMBAY_MUX(0x4, "CAM_M4"),
 478                          KEEMBAY_MUX(0x5, "I2S0_M5"),
 479                          KEEMBAY_MUX(0x6, "SLVDS1_M6"),
 480                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 481         KEEMBAY_PIN_DESC(38, "GPIO38",
 482                          KEEMBAY_MUX(0x0, "I3C1_M0"),
 483                          KEEMBAY_MUX(0x1, "SPI3_M1"),
 484                          KEEMBAY_MUX(0x2, "UART3_M2"),
 485                          KEEMBAY_MUX(0x3, "DEBUG_M3"),
 486                          KEEMBAY_MUX(0x4, "CAM_M4"),
 487                          KEEMBAY_MUX(0x5, "LCD_M5"),
 488                          KEEMBAY_MUX(0x6, "I2C2_M6"),
 489                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 490         KEEMBAY_PIN_DESC(39, "GPIO39",
 491                          KEEMBAY_MUX(0x0, "I3C1_M0"),
 492                          KEEMBAY_MUX(0x1, "SPI3_M1"),
 493                          KEEMBAY_MUX(0x2, "UART3_M2"),
 494                          KEEMBAY_MUX(0x3, "DEBUG_M3"),
 495                          KEEMBAY_MUX(0x4, "CAM_M4"),
 496                          KEEMBAY_MUX(0x5, "LCD_M5"),
 497                          KEEMBAY_MUX(0x6, "I2C2_M6"),
 498                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 499         KEEMBAY_PIN_DESC(40, "GPIO40",
 500                          KEEMBAY_MUX(0x0, "I2S2_M0"),
 501                          KEEMBAY_MUX(0x1, "SPI3_M1"),
 502                          KEEMBAY_MUX(0x2, "UART3_M2"),
 503                          KEEMBAY_MUX(0x3, "DEBUG_M3"),
 504                          KEEMBAY_MUX(0x4, "CAM_M4"),
 505                          KEEMBAY_MUX(0x5, "LCD_M5"),
 506                          KEEMBAY_MUX(0x6, "I2C3_M6"),
 507                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 508         KEEMBAY_PIN_DESC(41, "GPIO41",
 509                          KEEMBAY_MUX(0x0, "ETH_M0"),
 510                          KEEMBAY_MUX(0x1, "SPI3_M1"),
 511                          KEEMBAY_MUX(0x2, "SPI3_M2"),
 512                          KEEMBAY_MUX(0x3, "DEBUG_M3"),
 513                          KEEMBAY_MUX(0x4, "CAM_M4"),
 514                          KEEMBAY_MUX(0x5, "LCD_M5"),
 515                          KEEMBAY_MUX(0x6, "I2C3_M6"),
 516                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 517         KEEMBAY_PIN_DESC(42, "GPIO42",
 518                          KEEMBAY_MUX(0x0, "ETH_M0"),
 519                          KEEMBAY_MUX(0x1, "SD1_M1"),
 520                          KEEMBAY_MUX(0x2, "SPI3_M2"),
 521                          KEEMBAY_MUX(0x3, "CPR_M3"),
 522                          KEEMBAY_MUX(0x4, "CAM_M4"),
 523                          KEEMBAY_MUX(0x5, "LCD_M5"),
 524                          KEEMBAY_MUX(0x6, "I2C4_M6"),
 525                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 526         KEEMBAY_PIN_DESC(43, "GPIO43",
 527                          KEEMBAY_MUX(0x0, "ETH_M0"),
 528                          KEEMBAY_MUX(0x1, "SD1_M1"),
 529                          KEEMBAY_MUX(0x2, "SPI3_M2"),
 530                          KEEMBAY_MUX(0x3, "CPR_M3"),
 531                          KEEMBAY_MUX(0x4, "I2S0_M4"),
 532                          KEEMBAY_MUX(0x5, "LCD_M5"),
 533                          KEEMBAY_MUX(0x6, "I2C4_M6"),
 534                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 535         KEEMBAY_PIN_DESC(44, "GPIO44",
 536                          KEEMBAY_MUX(0x0, "ETH_M0"),
 537                          KEEMBAY_MUX(0x1, "SD1_M1"),
 538                          KEEMBAY_MUX(0x2, "SPI0_M2"),
 539                          KEEMBAY_MUX(0x3, "CPR_M3"),
 540                          KEEMBAY_MUX(0x4, "I2S0_M4"),
 541                          KEEMBAY_MUX(0x5, "LCD_M5"),
 542                          KEEMBAY_MUX(0x6, "CAM_M6"),
 543                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 544         KEEMBAY_PIN_DESC(45, "GPIO45",
 545                          KEEMBAY_MUX(0x0, "ETH_M0"),
 546                          KEEMBAY_MUX(0x1, "SD1_M1"),
 547                          KEEMBAY_MUX(0x2, "SPI0_M2"),
 548                          KEEMBAY_MUX(0x3, "CPR_M3"),
 549                          KEEMBAY_MUX(0x4, "I2S0_M4"),
 550                          KEEMBAY_MUX(0x5, "LCD_M5"),
 551                          KEEMBAY_MUX(0x6, "CAM_M6"),
 552                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 553         KEEMBAY_PIN_DESC(46, "GPIO46",
 554                          KEEMBAY_MUX(0x0, "ETH_M0"),
 555                          KEEMBAY_MUX(0x1, "SD1_M1"),
 556                          KEEMBAY_MUX(0x2, "SPI0_M2"),
 557                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 558                          KEEMBAY_MUX(0x4, "I2S0_M4"),
 559                          KEEMBAY_MUX(0x5, "LCD_M5"),
 560                          KEEMBAY_MUX(0x6, "CAM_M6"),
 561                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 562         KEEMBAY_PIN_DESC(47, "GPIO47",
 563                          KEEMBAY_MUX(0x0, "ETH_M0"),
 564                          KEEMBAY_MUX(0x1, "SD1_M1"),
 565                          KEEMBAY_MUX(0x2, "SPI0_M2"),
 566                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 567                          KEEMBAY_MUX(0x4, "I2S0_M4"),
 568                          KEEMBAY_MUX(0x5, "LCD_M5"),
 569                          KEEMBAY_MUX(0x6, "CAM_M6"),
 570                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 571         KEEMBAY_PIN_DESC(48, "GPIO48",
 572                          KEEMBAY_MUX(0x0, "ETH_M0"),
 573                          KEEMBAY_MUX(0x1, "SPI2_M1"),
 574                          KEEMBAY_MUX(0x2, "UART2_M2"),
 575                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 576                          KEEMBAY_MUX(0x4, "I2S0_M4"),
 577                          KEEMBAY_MUX(0x5, "LCD_M5"),
 578                          KEEMBAY_MUX(0x6, "CAM_M6"),
 579                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 580         KEEMBAY_PIN_DESC(49, "GPIO49",
 581                          KEEMBAY_MUX(0x0, "ETH_M0"),
 582                          KEEMBAY_MUX(0x1, "SPI2_M1"),
 583                          KEEMBAY_MUX(0x2, "UART2_M2"),
 584                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 585                          KEEMBAY_MUX(0x4, "I2S1_M4"),
 586                          KEEMBAY_MUX(0x5, "LCD_M5"),
 587                          KEEMBAY_MUX(0x6, "CAM_M6"),
 588                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 589         KEEMBAY_PIN_DESC(50, "GPIO50",
 590                          KEEMBAY_MUX(0x0, "ETH_M0"),
 591                          KEEMBAY_MUX(0x1, "SPI2_M1"),
 592                          KEEMBAY_MUX(0x2, "UART2_M2"),
 593                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 594                          KEEMBAY_MUX(0x4, "I2S1_M4"),
 595                          KEEMBAY_MUX(0x5, "LCD_M5"),
 596                          KEEMBAY_MUX(0x6, "CAM_M6"),
 597                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 598         KEEMBAY_PIN_DESC(51, "GPIO51",
 599                          KEEMBAY_MUX(0x0, "ETH_M0"),
 600                          KEEMBAY_MUX(0x1, "SPI2_M1"),
 601                          KEEMBAY_MUX(0x2, "UART2_M2"),
 602                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 603                          KEEMBAY_MUX(0x4, "I2S1_M4"),
 604                          KEEMBAY_MUX(0x5, "LCD_M5"),
 605                          KEEMBAY_MUX(0x6, "CAM_M6"),
 606                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 607         KEEMBAY_PIN_DESC(52, "GPIO52",
 608                          KEEMBAY_MUX(0x0, "ETH_M0"),
 609                          KEEMBAY_MUX(0x1, "SPI2_M1"),
 610                          KEEMBAY_MUX(0x2, "SD0_M2"),
 611                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 612                          KEEMBAY_MUX(0x4, "I2S1_M4"),
 613                          KEEMBAY_MUX(0x5, "LCD_M5"),
 614                          KEEMBAY_MUX(0x6, "CAM_M6"),
 615                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 616         KEEMBAY_PIN_DESC(53, "GPIO53",
 617                          KEEMBAY_MUX(0x0, "ETH_M0"),
 618                          KEEMBAY_MUX(0x1, "SPI2_M1"),
 619                          KEEMBAY_MUX(0x2, "SD0_M2"),
 620                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 621                          KEEMBAY_MUX(0x4, "I2S2_M4"),
 622                          KEEMBAY_MUX(0x5, "LCD_M5"),
 623                          KEEMBAY_MUX(0x6, "CAM_M6"),
 624                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 625         KEEMBAY_PIN_DESC(54, "GPIO54",
 626                          KEEMBAY_MUX(0x0, "ETH_M0"),
 627                          KEEMBAY_MUX(0x1, "SPI2_M1"),
 628                          KEEMBAY_MUX(0x2, "SD0_M2"),
 629                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 630                          KEEMBAY_MUX(0x4, "I2S2_M4"),
 631                          KEEMBAY_MUX(0x5, "LCD_M5"),
 632                          KEEMBAY_MUX(0x6, "CAM_M6"),
 633                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 634         KEEMBAY_PIN_DESC(55, "GPIO55",
 635                          KEEMBAY_MUX(0x0, "ETH_M0"),
 636                          KEEMBAY_MUX(0x1, "SPI2_M1"),
 637                          KEEMBAY_MUX(0x2, "SD1_M2"),
 638                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 639                          KEEMBAY_MUX(0x4, "I2S2_M4"),
 640                          KEEMBAY_MUX(0x5, "LCD_M5"),
 641                          KEEMBAY_MUX(0x6, "CAM_M6"),
 642                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 643         KEEMBAY_PIN_DESC(56, "GPIO56",
 644                          KEEMBAY_MUX(0x0, "ETH_M0"),
 645                          KEEMBAY_MUX(0x1, "SPI2_M1"),
 646                          KEEMBAY_MUX(0x2, "SD1_M2"),
 647                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 648                          KEEMBAY_MUX(0x4, "I2S2_M4"),
 649                          KEEMBAY_MUX(0x5, "LCD_M5"),
 650                          KEEMBAY_MUX(0x6, "CAM_M6"),
 651                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 652         KEEMBAY_PIN_DESC(57, "GPIO57",
 653                          KEEMBAY_MUX(0x0, "SPI1_M0"),
 654                          KEEMBAY_MUX(0x1, "I2S1_M1"),
 655                          KEEMBAY_MUX(0x2, "SD1_M2"),
 656                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 657                          KEEMBAY_MUX(0x4, "UART0_M4"),
 658                          KEEMBAY_MUX(0x5, "LCD_M5"),
 659                          KEEMBAY_MUX(0x6, "CAM_M6"),
 660                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 661         KEEMBAY_PIN_DESC(58, "GPIO58",
 662                          KEEMBAY_MUX(0x0, "SPI1_M0"),
 663                          KEEMBAY_MUX(0x1, "ETH_M1"),
 664                          KEEMBAY_MUX(0x2, "SD0_M2"),
 665                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 666                          KEEMBAY_MUX(0x4, "UART0_M4"),
 667                          KEEMBAY_MUX(0x5, "LCD_M5"),
 668                          KEEMBAY_MUX(0x6, "CAM_M6"),
 669                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 670         KEEMBAY_PIN_DESC(59, "GPIO59",
 671                          KEEMBAY_MUX(0x0, "SPI1_M0"),
 672                          KEEMBAY_MUX(0x1, "ETH_M1"),
 673                          KEEMBAY_MUX(0x2, "SD0_M2"),
 674                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 675                          KEEMBAY_MUX(0x4, "UART0_M4"),
 676                          KEEMBAY_MUX(0x5, "LCD_M5"),
 677                          KEEMBAY_MUX(0x6, "CAM_M6"),
 678                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 679         KEEMBAY_PIN_DESC(60, "GPIO60",
 680                          KEEMBAY_MUX(0x0, "SPI1_M0"),
 681                          KEEMBAY_MUX(0x1, "ETH_M1"),
 682                          KEEMBAY_MUX(0x2, "I3C1_M2"),
 683                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 684                          KEEMBAY_MUX(0x4, "UART0_M4"),
 685                          KEEMBAY_MUX(0x5, "LCD_M5"),
 686                          KEEMBAY_MUX(0x6, "CAM_M6"),
 687                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 688         KEEMBAY_PIN_DESC(61, "GPIO61",
 689                          KEEMBAY_MUX(0x0, "SPI1_M0"),
 690                          KEEMBAY_MUX(0x1, "ETH_M1"),
 691                          KEEMBAY_MUX(0x2, "SD0_M2"),
 692                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 693                          KEEMBAY_MUX(0x4, "UART1_M4"),
 694                          KEEMBAY_MUX(0x5, "LCD_M5"),
 695                          KEEMBAY_MUX(0x6, "CAM_M6"),
 696                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 697         KEEMBAY_PIN_DESC(62, "GPIO62",
 698                          KEEMBAY_MUX(0x0, "SPI1_M0"),
 699                          KEEMBAY_MUX(0x1, "ETH_M1"),
 700                          KEEMBAY_MUX(0x2, "SD1_M2"),
 701                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 702                          KEEMBAY_MUX(0x4, "UART1_M4"),
 703                          KEEMBAY_MUX(0x5, "LCD_M5"),
 704                          KEEMBAY_MUX(0x6, "CAM_M6"),
 705                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 706         KEEMBAY_PIN_DESC(63, "GPIO63",
 707                          KEEMBAY_MUX(0x0, "I2S1_M0"),
 708                          KEEMBAY_MUX(0x1, "SPI1_M1"),
 709                          KEEMBAY_MUX(0x2, "SD1_M2"),
 710                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 711                          KEEMBAY_MUX(0x4, "UART1_M4"),
 712                          KEEMBAY_MUX(0x5, "LCD_M5"),
 713                          KEEMBAY_MUX(0x6, "CAM_M6"),
 714                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 715         KEEMBAY_PIN_DESC(64, "GPIO64",
 716                          KEEMBAY_MUX(0x0, "I2S2_M0"),
 717                          KEEMBAY_MUX(0x1, "SPI1_M1"),
 718                          KEEMBAY_MUX(0x2, "ETH_M2"),
 719                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 720                          KEEMBAY_MUX(0x4, "UART1_M4"),
 721                          KEEMBAY_MUX(0x5, "LCD_M5"),
 722                          KEEMBAY_MUX(0x6, "CAM_M6"),
 723                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 724         KEEMBAY_PIN_DESC(65, "GPIO65",
 725                          KEEMBAY_MUX(0x0, "I3C0_M0"),
 726                          KEEMBAY_MUX(0x1, "SPI1_M1"),
 727                          KEEMBAY_MUX(0x2, "SD1_M2"),
 728                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 729                          KEEMBAY_MUX(0x4, "SPI0_M4"),
 730                          KEEMBAY_MUX(0x5, "LCD_M5"),
 731                          KEEMBAY_MUX(0x6, "CAM_M6"),
 732                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 733         KEEMBAY_PIN_DESC(66, "GPIO66",
 734                          KEEMBAY_MUX(0x0, "I3C0_M0"),
 735                          KEEMBAY_MUX(0x1, "ETH_M1"),
 736                          KEEMBAY_MUX(0x2, "I2C0_M2"),
 737                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 738                          KEEMBAY_MUX(0x4, "SPI0_M4"),
 739                          KEEMBAY_MUX(0x5, "LCD_M5"),
 740                          KEEMBAY_MUX(0x6, "CAM_M6"),
 741                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 742         KEEMBAY_PIN_DESC(67, "GPIO67",
 743                          KEEMBAY_MUX(0x0, "I3C1_M0"),
 744                          KEEMBAY_MUX(0x1, "ETH_M1"),
 745                          KEEMBAY_MUX(0x2, "I2C0_M2"),
 746                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 747                          KEEMBAY_MUX(0x4, "SPI0_M4"),
 748                          KEEMBAY_MUX(0x5, "LCD_M5"),
 749                          KEEMBAY_MUX(0x6, "I2S3_M6"),
 750                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 751         KEEMBAY_PIN_DESC(68, "GPIO68",
 752                          KEEMBAY_MUX(0x0, "I3C1_M0"),
 753                          KEEMBAY_MUX(0x1, "ETH_M1"),
 754                          KEEMBAY_MUX(0x2, "I2C1_M2"),
 755                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 756                          KEEMBAY_MUX(0x4, "SPI0_M4"),
 757                          KEEMBAY_MUX(0x5, "LCD_M5"),
 758                          KEEMBAY_MUX(0x6, "I2S3_M6"),
 759                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 760         KEEMBAY_PIN_DESC(69, "GPIO69",
 761                          KEEMBAY_MUX(0x0, "I3C2_M0"),
 762                          KEEMBAY_MUX(0x1, "ETH_M1"),
 763                          KEEMBAY_MUX(0x2, "I2C1_M2"),
 764                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 765                          KEEMBAY_MUX(0x4, "SPI0_M4"),
 766                          KEEMBAY_MUX(0x5, "LCD_M5"),
 767                          KEEMBAY_MUX(0x6, "I2S3_M6"),
 768                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 769         KEEMBAY_PIN_DESC(70, "GPIO70",
 770                          KEEMBAY_MUX(0x0, "I3C2_M0"),
 771                          KEEMBAY_MUX(0x1, "ETH_M1"),
 772                          KEEMBAY_MUX(0x2, "SPI0_M2"),
 773                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 774                          KEEMBAY_MUX(0x4, "SD0_M4"),
 775                          KEEMBAY_MUX(0x5, "LCD_M5"),
 776                          KEEMBAY_MUX(0x6, "I2S3_M6"),
 777                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 778         KEEMBAY_PIN_DESC(71, "GPIO71",
 779                          KEEMBAY_MUX(0x0, "I3C0_M0"),
 780                          KEEMBAY_MUX(0x1, "ETH_M1"),
 781                          KEEMBAY_MUX(0x2, "SLVDS1_M2"),
 782                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 783                          KEEMBAY_MUX(0x4, "SD0_M4"),
 784                          KEEMBAY_MUX(0x5, "LCD_M5"),
 785                          KEEMBAY_MUX(0x6, "I2S3_M6"),
 786                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 787         KEEMBAY_PIN_DESC(72, "GPIO72",
 788                          KEEMBAY_MUX(0x0, "I3C1_M0"),
 789                          KEEMBAY_MUX(0x1, "ETH_M1"),
 790                          KEEMBAY_MUX(0x2, "SLVDS1_M2"),
 791                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 792                          KEEMBAY_MUX(0x4, "SD0_M4"),
 793                          KEEMBAY_MUX(0x5, "LCD_M5"),
 794                          KEEMBAY_MUX(0x6, "UART2_M6"),
 795                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 796         KEEMBAY_PIN_DESC(73, "GPIO73",
 797                          KEEMBAY_MUX(0x0, "I3C2_M0"),
 798                          KEEMBAY_MUX(0x1, "ETH_M1"),
 799                          KEEMBAY_MUX(0x2, "SLVDS1_M2"),
 800                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 801                          KEEMBAY_MUX(0x4, "SD0_M4"),
 802                          KEEMBAY_MUX(0x5, "LCD_M5"),
 803                          KEEMBAY_MUX(0x6, "UART2_M6"),
 804                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 805         KEEMBAY_PIN_DESC(74, "GPIO74",
 806                          KEEMBAY_MUX(0x0, "I3C0_M0"),
 807                          KEEMBAY_MUX(0x1, "ETH_M1"),
 808                          KEEMBAY_MUX(0x2, "SLVDS1_M2"),
 809                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 810                          KEEMBAY_MUX(0x4, "SD0_M4"),
 811                          KEEMBAY_MUX(0x5, "LCD_M5"),
 812                          KEEMBAY_MUX(0x6, "UART2_M6"),
 813                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 814         KEEMBAY_PIN_DESC(75, "GPIO75",
 815                          KEEMBAY_MUX(0x0, "I3C0_M0"),
 816                          KEEMBAY_MUX(0x1, "ETH_M1"),
 817                          KEEMBAY_MUX(0x2, "SLVDS1_M2"),
 818                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 819                          KEEMBAY_MUX(0x4, "SD0_M4"),
 820                          KEEMBAY_MUX(0x5, "LCD_M5"),
 821                          KEEMBAY_MUX(0x6, "UART2_M6"),
 822                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 823         KEEMBAY_PIN_DESC(76, "GPIO76",
 824                          KEEMBAY_MUX(0x0, "I2C2_M0"),
 825                          KEEMBAY_MUX(0x1, "I3C0_M1"),
 826                          KEEMBAY_MUX(0x2, "SLVDS1_M2"),
 827                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 828                          KEEMBAY_MUX(0x4, "ETH_M4"),
 829                          KEEMBAY_MUX(0x5, "LCD_M5"),
 830                          KEEMBAY_MUX(0x6, "UART3_M6"),
 831                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 832         KEEMBAY_PIN_DESC(77, "GPIO77",
 833                          KEEMBAY_MUX(0x0, "PCIE_M0"),
 834                          KEEMBAY_MUX(0x1, "I3C1_M1"),
 835                          KEEMBAY_MUX(0x2, "SLVDS1_M2"),
 836                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 837                          KEEMBAY_MUX(0x4, "I3C2_M4"),
 838                          KEEMBAY_MUX(0x5, "LCD_M5"),
 839                          KEEMBAY_MUX(0x6, "UART3_M6"),
 840                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 841         KEEMBAY_PIN_DESC(78, "GPIO78",
 842                          KEEMBAY_MUX(0x0, "PCIE_M0"),
 843                          KEEMBAY_MUX(0x1, "I3C2_M1"),
 844                          KEEMBAY_MUX(0x2, "SLVDS1_M2"),
 845                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 846                          KEEMBAY_MUX(0x4, "I3C2_M4"),
 847                          KEEMBAY_MUX(0x5, "LCD_M5"),
 848                          KEEMBAY_MUX(0x6, "UART3_M6"),
 849                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 850         KEEMBAY_PIN_DESC(79, "GPIO79",
 851                          KEEMBAY_MUX(0x0, "PCIE_M0"),
 852                          KEEMBAY_MUX(0x1, "I2C2_M1"),
 853                          KEEMBAY_MUX(0x2, "SLVDS1_M2"),
 854                          KEEMBAY_MUX(0x3, "TPIU_M3"),
 855                          KEEMBAY_MUX(0x4, "I3C2_M4"),
 856                          KEEMBAY_MUX(0x5, "LCD_M5"),
 857                          KEEMBAY_MUX(0x6, "UART3_M6"),
 858                          KEEMBAY_MUX(0x7, "GPIO_M7")),
 859 };
 860
 861 static inline u32 keembay_read_reg(void __iomem *base, unsigned int pin)
 862 {
 863         return readl(base + KEEMBAY_GPIO_REG_OFFSET(pin));
 864 }
 865
 866 static inline u32 keembay_read_gpio_reg(void __iomem *base, unsigned int pin)
 867 {
 868         return keembay_read_reg(base, pin / KEEMBAY_GPIO_MAX_PER_REG);
 869 }
 870
 871 static inline u32 keembay_read_pin(void __iomem *base, unsigned int pin)
 872 {
 873         u32 val = keembay_read_gpio_reg(base, pin);
 874
 875         return !!(val & BIT(pin % KEEMBAY_GPIO_MAX_PER_REG));
 876 }
 877
 878 static inline void keembay_write_reg(u32 val, void __iomem *base, unsigned int pin)
 879 {
 880         writel(val, base + KEEMBAY_GPIO_REG_OFFSET(pin));
 881 }
 882
 883 static inline void keembay_write_gpio_reg(u32 val, void __iomem *base, unsigned int pin)
 884 {
 885         keembay_write_reg(val, base, pin / KEEMBAY_GPIO_MAX_PER_REG);
 886 }
 887
 888 static void keembay_gpio_invert(struct keembay_pinctrl *kpc, unsigned int pin)
 889 {
 890         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 891
 892         /*
 893          * This IP doesn't support the falling edge and low level interrupt
 894          * trigger. Invert API is used to mimic the falling edge and low
 895          * level support
 896          */
 897
 898         val |= FIELD_PREP(KEEMBAY_GPIO_MODE_INV_MASK, KEEMBAY_GPIO_MODE_INV_VAL);
 899         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 900 }
 901
 902 static void keembay_gpio_restore_default(struct keembay_pinctrl *kpc, unsigned int pin)
 903 {
 904         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 905
 906         val &= FIELD_PREP(KEEMBAY_GPIO_MODE_INV_MASK, 0);
 907         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 908 }
 909
 910 static int keembay_request_gpio(struct pinctrl_dev *pctldev,
 911                                 struct pinctrl_gpio_range *range, unsigned int pin)
 912 {
 913         struct keembay_pinctrl *kpc = pinctrl_dev_get_drvdata(pctldev);
 914         unsigned int val;
 915
 916         if (pin >= kpc->npins)
 917                 return -EINVAL;
 918
 919         val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 920         val = FIELD_GET(KEEMBAY_GPIO_MODE_SELECT_MASK, val);
 921
 922         /* As per Pin Mux Map, Modes 0 to 6 are for peripherals */
 923         if (val != KEEMBAY_GPIO_MODE_DEFAULT)
 924                 return -EBUSY;
 925
 926         return 0;
 927 }
 928
 929 static int keembay_set_mux(struct pinctrl_dev *pctldev, unsigned int fun_sel,
 930                            unsigned int grp_sel)
 931 {
 932         struct keembay_pinctrl *kpc = pinctrl_dev_get_drvdata(pctldev);
 933         struct function_desc *func;
 934         struct group_desc *grp;
 935         unsigned int val;
 936         u8 pin_mode;
 937         int pin;
 938
 939         grp = pinctrl_generic_get_group(pctldev, grp_sel);
 940         if (!grp)
 941                 return -EINVAL;
 942
 943         func = pinmux_generic_get_function(pctldev, fun_sel);
 944         if (!func)
 945                 return -EINVAL;
 946
 947         /* Change modes for pins in the selected group */
 948         pin = *grp->pins;
 949         pin_mode = *(u8 *)(func->data);
 950
 951         val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 952         val = u32_replace_bits(val, pin_mode, KEEMBAY_GPIO_MODE_SELECT_MASK);
 953         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 954
 955         return 0;
 956 }
 957
 958 static u32 keembay_pinconf_get_pull(struct keembay_pinctrl *kpc, unsigned int pin)
 959 {
 960         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 961
 962         return FIELD_GET(KEEMBAY_GPIO_MODE_PULLUP_MASK, val);
 963 }
 964
 965 static int keembay_pinconf_set_pull(struct keembay_pinctrl *kpc, unsigned int pin,
 966                                     unsigned int pull)
 967 {
 968         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 969
 970         val = u32_replace_bits(val, pull, KEEMBAY_GPIO_MODE_PULLUP_MASK);
 971         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 972
 973         return 0;
 974 }
 975
 976 static int keembay_pinconf_get_drive(struct keembay_pinctrl *kpc, unsigned int pin)
 977 {
 978         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 979
 980         val = FIELD_GET(KEEMBAY_GPIO_MODE_DRIVE_MASK, val) * 4;
 981         if (val)
 982                 return val;
 983
 984         return KEEMBAY_GPIO_MIN_STRENGTH;
 985 }
 986
 987 static int keembay_pinconf_set_drive(struct keembay_pinctrl *kpc, unsigned int pin,
 988                                      unsigned int drive)
 989 {
 990         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 991         unsigned int strength = clamp_val(drive, KEEMBAY_GPIO_MIN_STRENGTH,
 992                                  KEEMBAY_GPIO_MAX_STRENGTH) / 4;
 993
 994         val = u32_replace_bits(val, strength, KEEMBAY_GPIO_MODE_DRIVE_MASK);
 995         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_MODE, pin);
 996
 997         return 0;
 998 }
 999
1000 static int keembay_pinconf_get_slew_rate(struct keembay_pinctrl *kpc, unsigned int pin)
1001 {
1002         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1003
1004         return !!(val & KEEMBAY_GPIO_MODE_SLEW_RATE);
1005 }
1006
1007 static int keembay_pinconf_set_slew_rate(struct keembay_pinctrl *kpc, unsigned int pin,
1008                                          unsigned int slew_rate)
1009 {
1010         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1011
1012         if (slew_rate)
1013                 val |= KEEMBAY_GPIO_MODE_SLEW_RATE;
1014         else
1015                 val &= ~KEEMBAY_GPIO_MODE_SLEW_RATE;
1016
1017         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1018
1019         return 0;
1020 }
1021
1022 static int keembay_pinconf_get_schmitt(struct keembay_pinctrl *kpc, unsigned int pin)
1023 {
1024         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1025
1026         return !!(val & KEEMBAY_GPIO_MODE_SCHMITT_EN);
1027 }
1028
1029 static int keembay_pinconf_set_schmitt(struct keembay_pinctrl *kpc, unsigned int pin,
1030                                        unsigned int schmitt_en)
1031 {
1032         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1033
1034         if (schmitt_en)
1035                 val |= KEEMBAY_GPIO_MODE_SCHMITT_EN;
1036         else
1037                 val &= ~KEEMBAY_GPIO_MODE_SCHMITT_EN;
1038
1039         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1040
1041         return 0;
1042 }
1043
1044 static int keembay_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
1045                                unsigned long *cfg)
1046 {
1047         struct keembay_pinctrl *kpc = pinctrl_dev_get_drvdata(pctldev);
1048         unsigned int param = pinconf_to_config_param(*cfg);
1049         unsigned int val;
1050
1051         if (pin >= kpc->npins)
1052                 return -EINVAL;
1053
1054         switch (param) {
1055         case PIN_CONFIG_BIAS_DISABLE:
1056                 if (keembay_pinconf_get_pull(kpc, pin) != KEEMBAY_GPIO_DISABLE)
1057                         return -EINVAL;
1058                 break;
1059
1060         case PIN_CONFIG_BIAS_PULL_UP:
1061                 if (keembay_pinconf_get_pull(kpc, pin) != KEEMBAY_GPIO_PULL_UP)
1062                         return -EINVAL;
1063                 break;
1064
1065         case PIN_CONFIG_BIAS_PULL_DOWN:
1066                 if (keembay_pinconf_get_pull(kpc, pin) != KEEMBAY_GPIO_PULL_DOWN)
1067                         return -EINVAL;
1068                 break;
1069
1070         case PIN_CONFIG_BIAS_BUS_HOLD:
1071                 if (keembay_pinconf_get_pull(kpc, pin) != KEEMBAY_GPIO_BUS_HOLD)
1072                         return -EINVAL;
1073                 break;
1074
1075         case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
1076                 if (!keembay_pinconf_get_schmitt(kpc, pin))
1077                         return -EINVAL;
1078                 break;
1079
1080         case PIN_CONFIG_SLEW_RATE:
1081                 val = keembay_pinconf_get_slew_rate(kpc, pin);
1082                 *cfg = pinconf_to_config_packed(param, val);
1083                 break;
1084
1085         case PIN_CONFIG_DRIVE_STRENGTH:
1086                 val = keembay_pinconf_get_drive(kpc, pin);
1087                 *cfg = pinconf_to_config_packed(param, val);
1088                 break;
1089
1090         default:
1091                 return -ENOTSUPP;
1092         }
1093
1094         return 0;
1095 }
1096
1097 static int keembay_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
1098                                unsigned long *cfg, unsigned int num_configs)
1099 {
1100         struct keembay_pinctrl *kpc = pinctrl_dev_get_drvdata(pctldev);
1101         enum pin_config_param param;
1102         unsigned int arg, i;
1103         int ret = 0;
1104
1105         if (pin >= kpc->npins)
1106                 return -EINVAL;
1107
1108         for (i = 0; i < num_configs; i++) {
1109                 param = pinconf_to_config_param(cfg[i]);
1110                 arg = pinconf_to_config_argument(cfg[i]);
1111
1112                 switch (param) {
1113                 case PIN_CONFIG_BIAS_DISABLE:
1114                         ret = keembay_pinconf_set_pull(kpc, pin, KEEMBAY_GPIO_DISABLE);
1115                         break;
1116
1117                 case PIN_CONFIG_BIAS_PULL_UP:
1118                         ret = keembay_pinconf_set_pull(kpc, pin, KEEMBAY_GPIO_PULL_UP);
1119                         break;
1120
1121                 case PIN_CONFIG_BIAS_PULL_DOWN:
1122                         ret = keembay_pinconf_set_pull(kpc, pin, KEEMBAY_GPIO_PULL_DOWN);
1123                         break;
1124
1125                 case PIN_CONFIG_BIAS_BUS_HOLD:
1126                         ret = keembay_pinconf_set_pull(kpc, pin, KEEMBAY_GPIO_BUS_HOLD);
1127                         break;
1128
1129                 case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
1130                         ret = keembay_pinconf_set_schmitt(kpc, pin, arg);
1131                         break;
1132
1133                 case PIN_CONFIG_SLEW_RATE:
1134                         ret = keembay_pinconf_set_slew_rate(kpc, pin, arg);
1135                         break;
1136
1137                 case PIN_CONFIG_DRIVE_STRENGTH:
1138                         ret = keembay_pinconf_set_drive(kpc, pin, arg);
1139                         break;
1140
1141                 default:
1142                         return -ENOTSUPP;
1143                 }
1144                 if (ret)
1145                         return ret;
1146         }
1147         return ret;
1148 }
1149
1150 static const struct pinctrl_ops keembay_pctlops = {
1151         .get_groups_count       = pinctrl_generic_get_group_count,
1152         .get_group_name         = pinctrl_generic_get_group_name,
1153         .get_group_pins         = pinctrl_generic_get_group_pins,
1154         .dt_node_to_map         = pinconf_generic_dt_node_to_map_all,
1155         .dt_free_map            = pinconf_generic_dt_free_map,
1156 };
1157
1158 static const struct pinmux_ops keembay_pmxops = {
1159         .get_functions_count    = pinmux_generic_get_function_count,
1160         .get_function_name      = pinmux_generic_get_function_name,
1161         .get_function_groups    = pinmux_generic_get_function_groups,
1162         .gpio_request_enable    = keembay_request_gpio,
1163         .set_mux                = keembay_set_mux,
1164 };
1165
1166 static const struct pinconf_ops keembay_confops = {
1167         .is_generic     = true,
1168         .pin_config_get = keembay_pinconf_get,
1169         .pin_config_set = keembay_pinconf_set,
1170 };
1171
1172 static struct pinctrl_desc keembay_pinctrl_desc = {
1173         .name           = "keembay-pinmux",
1174         .pctlops        = &keembay_pctlops,
1175         .pmxops         = &keembay_pmxops,
1176         .confops        = &keembay_confops,
1177         .owner          = THIS_MODULE,
1178 };
1179
1180 static int keembay_gpio_get(struct gpio_chip *gc, unsigned int pin)
1181 {
1182         struct keembay_pinctrl *kpc = gpiochip_get_data(gc);
1183         unsigned int val, offset;
1184
1185         val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1186         offset = (val & KEEMBAY_GPIO_MODE_DIR) ? KEEMBAY_GPIO_DATA_IN : KEEMBAY_GPIO_DATA_OUT;
1187
1188         return keembay_read_pin(kpc->base0 + offset, pin);
1189 }
1190
1191 static void keembay_gpio_set(struct gpio_chip *gc, unsigned int pin, int val)
1192 {
1193         struct keembay_pinctrl *kpc = gpiochip_get_data(gc);
1194         unsigned int reg_val;
1195
1196         reg_val = keembay_read_gpio_reg(kpc->base0 + KEEMBAY_GPIO_DATA_OUT, pin);
1197         if (val)
1198                 keembay_write_gpio_reg(reg_val | BIT(pin % KEEMBAY_GPIO_MAX_PER_REG),
1199                                        kpc->base0 + KEEMBAY_GPIO_DATA_HIGH, pin);
1200         else
1201                 keembay_write_gpio_reg(~reg_val | BIT(pin % KEEMBAY_GPIO_MAX_PER_REG),
1202                                        kpc->base0 + KEEMBAY_GPIO_DATA_LOW, pin);
1203 }
1204
1205 static int keembay_gpio_get_direction(struct gpio_chip *gc, unsigned int pin)
1206 {
1207         struct keembay_pinctrl *kpc = gpiochip_get_data(gc);
1208         unsigned int val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1209
1210         return !!(val & KEEMBAY_GPIO_MODE_DIR);
1211 }
1212
1213 static int keembay_gpio_set_direction_in(struct gpio_chip *gc, unsigned int pin)
1214 {
1215         struct keembay_pinctrl *kpc = gpiochip_get_data(gc);
1216         unsigned int val;
1217
1218         val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1219         val |= KEEMBAY_GPIO_MODE_DIR;
1220         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1221
1222         return 0;
1223 }
1224
1225 static int keembay_gpio_set_direction_out(struct gpio_chip *gc,
1226                                           unsigned int pin, int value)
1227 {
1228         struct keembay_pinctrl *kpc = gpiochip_get_data(gc);
1229         unsigned int val;
1230
1231         val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1232         val &= ~KEEMBAY_GPIO_MODE_DIR;
1233         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_MODE, pin);
1234         keembay_gpio_set(gc, pin, value);
1235
1236         return 0;
1237 }
1238
1239 static void keembay_gpio_irq_handler(struct irq_desc *desc)
1240 {
1241         struct gpio_chip *gc = irq_desc_get_handler_data(desc);
1242         unsigned int kmb_irq = irq_desc_get_irq(desc);
1243         unsigned long reg, clump = 0, bit = 0;
1244         struct irq_chip *parent_chip;
1245         struct keembay_pinctrl *kpc;
1246         unsigned int src, pin, val;
1247
1248         /* Identify GPIO interrupt number from GIC interrupt number */
1249         for (src = 0; src < KEEMBAY_GPIO_NUM_IRQ; src++) {
1250                 if (kmb_irq == gc->irq.parents[src])
1251                         break;
1252         }
1253
1254         if (src == KEEMBAY_GPIO_NUM_IRQ)
1255                 return;
1256
1257         parent_chip = irq_desc_get_chip(desc);
1258         kpc = gpiochip_get_data(gc);
1259
1260         chained_irq_enter(parent_chip, desc);
1261         reg = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_INT_CFG, src);
1262
1263         /*
1264          * Each Interrupt line can be shared by up to 4 GPIO pins. Enable bit
1265          * and input values were checked to identify the source of the
1266          * Interrupt. The checked enable bit positions are 7, 15, 23 and 31.
1267          */
1268         for_each_set_clump8(bit, clump, &reg, BITS_PER_TYPE(typeof(reg))) {
1269                 pin = clump & ~KEEMBAY_GPIO_IRQ_ENABLE;
1270                 val = keembay_read_pin(kpc->base0 + KEEMBAY_GPIO_DATA_IN, pin);
1271                 kmb_irq = irq_linear_revmap(gc->irq.domain, pin);
1272
1273                 /* Checks if the interrupt is enabled */
1274                 if (val && (clump & KEEMBAY_GPIO_IRQ_ENABLE))
1275                         generic_handle_irq(kmb_irq);
1276         }
1277         chained_irq_exit(parent_chip, desc);
1278 }
1279
1280 static void keembay_gpio_clear_irq(struct irq_data *data, unsigned long pos,
1281                                    u32 src, irq_hw_number_t pin)
1282 {
1283         struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
1284         struct keembay_pinctrl *kpc = gpiochip_get_data(gc);
1285         unsigned long trig = irqd_get_trigger_type(data);
1286         struct keembay_gpio_irq *irq = &kpc->irq[src];
1287         unsigned long val;
1288
1289         /* Check if the value of pos/KEEMBAY_GPIO_NUM_IRQ is in valid range. */
1290         if ((pos / KEEMBAY_GPIO_NUM_IRQ) >= KEEMBAY_GPIO_MAX_PER_IRQ)
1291                 return;
1292
1293         /* Retains val register as it handles other interrupts as well. */
1294         val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_INT_CFG, src);
1295
1296         bitmap_set_value8(&val, 0, pos);
1297         keembay_write_reg(val, kpc->base1 + KEEMBAY_GPIO_INT_CFG, src);
1298
1299         irq->num_share--;
1300         irq->pins[pos / KEEMBAY_GPIO_NUM_IRQ] = 0;
1301
1302         if (trig & IRQ_TYPE_LEVEL_MASK)
1303                 keembay_gpio_restore_default(kpc, pin);
1304
1305         if (irq->trigger == IRQ_TYPE_LEVEL_HIGH)
1306                 kpc->max_gpios_level_type++;
1307         else if (irq->trigger == IRQ_TYPE_EDGE_RISING)
1308                 kpc->max_gpios_edge_type++;
1309 }
1310
1311 static int keembay_find_free_slot(struct keembay_pinctrl *kpc, unsigned int src)
1312 {
1313         unsigned long val = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_INT_CFG, src);
1314
1315         return bitmap_find_free_region(&val, KEEMBAY_GPIO_MAX_PER_REG, 3) / KEEMBAY_GPIO_NUM_IRQ;
1316 }
1317
1318 static int keembay_find_free_src(struct keembay_pinctrl *kpc, unsigned int trig)
1319 {
1320         int src, type = 0;
1321
1322         if (trig & IRQ_TYPE_LEVEL_MASK)
1323                 type = IRQ_TYPE_LEVEL_HIGH;
1324         else if (trig & IRQ_TYPE_EDGE_BOTH)
1325                 type = IRQ_TYPE_EDGE_RISING;
1326
1327         for (src = 0; src < KEEMBAY_GPIO_NUM_IRQ; src++) {
1328                 if (kpc->irq[src].trigger != type)
1329                         continue;
1330
1331                 if (!keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_INT_CFG, src) ||
1332                     kpc->irq[src].num_share < KEEMBAY_GPIO_MAX_PER_IRQ)
1333                         return src;
1334         }
1335
1336         return -EBUSY;
1337 }
1338
1339 static void keembay_gpio_set_irq(struct keembay_pinctrl *kpc, int src,
1340                                  int slot, irq_hw_number_t pin)
1341 {
1342         unsigned long val = pin | KEEMBAY_GPIO_IRQ_ENABLE;
1343         struct keembay_gpio_irq *irq = &kpc->irq[src];
1344         unsigned long flags, reg;
1345
1346         raw_spin_lock_irqsave(&kpc->lock, flags);
1347         reg = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_INT_CFG, src);
1348         bitmap_set_value8(&reg, val, slot * 8);
1349         keembay_write_reg(reg, kpc->base1 + KEEMBAY_GPIO_INT_CFG, src);
1350         raw_spin_unlock_irqrestore(&kpc->lock, flags);
1351
1352         if (irq->trigger == IRQ_TYPE_LEVEL_HIGH)
1353                 kpc->max_gpios_level_type--;
1354         else if (irq->trigger == IRQ_TYPE_EDGE_RISING)
1355                 kpc->max_gpios_edge_type--;
1356
1357         irq->source = src;
1358         irq->pins[slot] = pin;
1359         irq->num_share++;
1360 }
1361
1362 static void keembay_gpio_irq_enable(struct irq_data *data)
1363 {
1364         struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
1365         struct keembay_pinctrl *kpc = gpiochip_get_data(gc);
1366         unsigned int trig = irqd_get_trigger_type(data);
1367         irq_hw_number_t pin = irqd_to_hwirq(data);
1368         int src, slot;
1369
1370         /* Check which Interrupt source and slot is available */
1371         src = keembay_find_free_src(kpc, trig);
1372         slot = keembay_find_free_slot(kpc, src);
1373
1374         if (src < 0 || slot < 0)
1375                 return;
1376
1377         if (trig & KEEMBAY_GPIO_SENSE_LOW)
1378                 keembay_gpio_invert(kpc, pin);
1379
1380         keembay_gpio_set_irq(kpc, src, slot, pin);
1381 }
1382
1383 static void keembay_gpio_irq_ack(struct irq_data *data)
1384 {
1385         /*
1386          * The keembay_gpio_irq_ack function is needed to handle_edge_irq.
1387          * IRQ ack is not possible from the SOC perspective. The IP by itself
1388          * is used for handling interrupts which do not come in short-time and
1389          * not used as protocol or communication interrupts. All the interrupts
1390          * are threaded IRQ interrupts. But this function is expected to be
1391          * present as the gpio IP is registered with irq framework. Otherwise
1392          * handle_edge_irq() fails.
1393          */
1394 }
1395
1396 static void keembay_gpio_irq_disable(struct irq_data *data)
1397 {
1398         struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
1399         struct keembay_pinctrl *kpc = gpiochip_get_data(gc);
1400         irq_hw_number_t pin = irqd_to_hwirq(data);
1401         unsigned long reg, clump = 0, pos = 0;
1402         unsigned int src;
1403
1404         for (src = 0; src < KEEMBAY_GPIO_NUM_IRQ; src++) {
1405                 reg = keembay_read_reg(kpc->base1 + KEEMBAY_GPIO_INT_CFG, src);
1406                 for_each_set_clump8(pos, clump, &reg, BITS_PER_TYPE(typeof(reg))) {
1407                         if ((clump & ~KEEMBAY_GPIO_IRQ_ENABLE) == pin) {
1408                                 keembay_gpio_clear_irq(data, pos, src, pin);
1409                                 return;
1410                         }
1411                 }
1412         }
1413 }
1414
1415 static int keembay_gpio_irq_set_type(struct irq_data *data, unsigned int type)
1416 {
1417         struct gpio_chip *gc = irq_data_get_irq_chip_data(data);
1418         struct keembay_pinctrl *kpc = gpiochip_get_data(gc);
1419
1420         /* Change EDGE_BOTH as EDGE_RISING in order to claim the IRQ for power button */
1421         if (!kpc->max_gpios_edge_type && (type & IRQ_TYPE_EDGE_BOTH))
1422                 type = IRQ_TYPE_EDGE_RISING;
1423
1424         if (!kpc->max_gpios_level_type && (type & IRQ_TYPE_LEVEL_MASK))
1425                 type = IRQ_TYPE_NONE;
1426
1427         if (type & IRQ_TYPE_EDGE_BOTH)
1428                 irq_set_handler_locked(data, handle_edge_irq);
1429         else if (type & IRQ_TYPE_LEVEL_MASK)
1430                 irq_set_handler_locked(data, handle_level_irq);
1431         else
1432                 return -EINVAL;
1433
1434         return 0;
1435 }
1436
1437 static int keembay_gpio_add_pin_ranges(struct gpio_chip *chip)
1438 {
1439         struct keembay_pinctrl *kpc = gpiochip_get_data(chip);
1440         int ret;
1441
1442         ret = gpiochip_add_pin_range(chip, dev_name(kpc->dev), 0, 0, chip->ngpio);
1443         if (ret)
1444                 dev_err_probe(kpc->dev, ret, "failed to add GPIO pin range\n");
1445         return ret;
1446 }
1447
1448 static struct irq_chip keembay_gpio_irqchip = {
1449         .name = "keembay-gpio",
1450         .irq_enable = keembay_gpio_irq_enable,
1451         .irq_disable = keembay_gpio_irq_disable,
1452         .irq_set_type = keembay_gpio_irq_set_type,
1453         .irq_ack = keembay_gpio_irq_ack,
1454 };
1455
1456 static int keembay_gpiochip_probe(struct keembay_pinctrl *kpc,
1457                                   struct platform_device *pdev)
1458 {
1459         unsigned int i, level_line = 0, edge_line = 0;
1460         struct gpio_chip *gc = &kpc->chip;
1461         struct gpio_irq_chip *girq;
1462
1463         /* Setup GPIO IRQ chip */
1464         girq                    = &kpc->chip.irq;
1465         girq->chip              = &keembay_gpio_irqchip;
1466         girq->parent_handler    = keembay_gpio_irq_handler;
1467         girq->num_parents       = KEEMBAY_GPIO_NUM_IRQ;
1468         girq->parents           = devm_kcalloc(kpc->dev, girq->num_parents,
1469                                                sizeof(*girq->parents), GFP_KERNEL);
1470
1471         if (!girq->parents)
1472                 return -ENOMEM;
1473
1474         /* Setup GPIO chip */
1475         gc->label               = dev_name(kpc->dev);
1476         gc->parent              = kpc->dev;
1477         gc->request             = gpiochip_generic_request;
1478         gc->free                = gpiochip_generic_free;
1479         gc->get_direction       = keembay_gpio_get_direction;
1480         gc->direction_input     = keembay_gpio_set_direction_in;
1481         gc->direction_output    = keembay_gpio_set_direction_out;
1482         gc->get                 = keembay_gpio_get;
1483         gc->set                 = keembay_gpio_set;
1484         gc->set_config          = gpiochip_generic_config;
1485         gc->base                = -1;
1486         gc->ngpio               = kpc->npins;
1487         gc->add_pin_ranges      = keembay_gpio_add_pin_ranges;
1488
1489         for (i = 0; i < KEEMBAY_GPIO_NUM_IRQ; i++) {
1490                 struct keembay_gpio_irq *kmb_irq = &kpc->irq[i];
1491                 int irq;
1492
1493                 irq = platform_get_irq_optional(pdev, i);
1494                 if (irq <= 0)
1495                         continue;
1496
1497                 girq->parents[i]        = irq;
1498                 kmb_irq->line   = girq->parents[i];
1499                 kmb_irq->source = i;
1500                 kmb_irq->trigger        = irq_get_trigger_type(girq->parents[i]);
1501                 kmb_irq->num_share      = 0;
1502
1503                 if (kmb_irq->trigger == IRQ_TYPE_LEVEL_HIGH)
1504                         level_line++;
1505                 else
1506                         edge_line++;
1507         }
1508
1509         kpc->max_gpios_level_type = level_line * KEEMBAY_GPIO_MAX_PER_IRQ;
1510         kpc->max_gpios_edge_type = edge_line * KEEMBAY_GPIO_MAX_PER_IRQ;
1511
1512         girq->default_type = IRQ_TYPE_NONE;
1513         girq->handler = handle_bad_irq;
1514
1515         return devm_gpiochip_add_data(kpc->dev, gc, kpc);
1516 }
1517
1518 static int keembay_build_groups(struct keembay_pinctrl *kpc)
1519 {
1520         struct group_desc *grp;
1521         unsigned int i;
1522
1523         kpc->ngroups = kpc->npins;
1524         grp = devm_kcalloc(kpc->dev, kpc->ngroups, sizeof(*grp), GFP_KERNEL);
1525         if (!grp)
1526                 return -ENOMEM;
1527
1528         /* Each pin is categorised as one group */
1529         for (i = 0; i < kpc->ngroups; i++) {
1530                 const struct pinctrl_pin_desc *pdesc = keembay_pins + i;
1531                 struct group_desc *kmb_grp = grp + i;
1532
1533                 kmb_grp->name = pdesc->name;
1534                 kmb_grp->pins = (int *)&pdesc->number;
1535                 pinctrl_generic_add_group(kpc->pctrl, kmb_grp->name,
1536                                           kmb_grp->pins, 1, NULL);
1537         }
1538
1539         return 0;
1540 }
1541
1542 static int keembay_pinctrl_reg(struct keembay_pinctrl *kpc,  struct device *dev)
1543 {
1544         int ret;
1545
1546         keembay_pinctrl_desc.pins = keembay_pins;
1547         ret = of_property_read_u32(dev->of_node, "ngpios", &kpc->npins);
1548         if (ret < 0)
1549                 return ret;
1550         keembay_pinctrl_desc.npins = kpc->npins;
1551
1552         kpc->pctrl = devm_pinctrl_register(kpc->dev, &keembay_pinctrl_desc, kpc);
1553
1554         return PTR_ERR_OR_ZERO(kpc->pctrl);
1555 }
1556
1557 static int keembay_add_functions(struct keembay_pinctrl *kpc,
1558                                  struct function_desc *function)
1559 {
1560         unsigned int i;
1561
1562         /* Assign the groups for each function */
1563         for (i = 0; i < kpc->npins; i++) {
1564                 const struct pinctrl_pin_desc *pdesc = keembay_pins + i;
1565                 struct keembay_mux_desc *mux = pdesc->drv_data;
1566
1567                 while (mux->name) {
1568                         struct function_desc *func;
1569                         const char **grp;
1570                         size_t grp_size;
1571                         u32 j, grp_num;
1572
1573                         for (j = 0; j < kpc->nfuncs; j++) {
1574                                 if (!strcmp(mux->name, function[j].name))
1575                                         break;
1576                         }
1577
1578                         if (j == kpc->nfuncs)
1579                                 return -EINVAL;
1580
1581                         func = function + j;
1582                         grp_num = func->num_group_names;
1583                         grp_size = sizeof(*func->group_names);
1584
1585                         if (!func->group_names) {
1586                                 func->group_names = devm_kcalloc(kpc->dev,
1587                                                                  grp_num,
1588                                                                  grp_size,
1589                                                                  GFP_KERNEL);
1590                                 if (!func->group_names)
1591                                         return -ENOMEM;
1592                         }
1593
1594                         grp = func->group_names;
1595                         while (*grp)
1596                                 grp++;
1597
1598                         *grp = pdesc->name;
1599                         mux++;
1600                 }
1601         }
1602
1603         /* Add all functions */
1604         for (i = 0; i < kpc->nfuncs; i++) {
1605                 pinmux_generic_add_function(kpc->pctrl,
1606                                             function[i].name,
1607                                             function[i].group_names,
1608                                             function[i].num_group_names,
1609                                             function[i].data);
1610         }
1611
1612         return 0;
1613 }
1614
1615 static int keembay_build_functions(struct keembay_pinctrl *kpc)
1616 {
1617         struct function_desc *keembay_funcs, *new_funcs;
1618         int i;
1619
1620         /* Allocate total number of functions */
1621         kpc->nfuncs = 0;
1622         keembay_funcs = kcalloc(kpc->npins * 8, sizeof(*keembay_funcs), GFP_KERNEL);
1623         if (!keembay_funcs)
1624                 return -ENOMEM;
1625
1626         /* Find total number of functions and each's properties */
1627         for (i = 0; i < kpc->npins; i++) {
1628                 const struct pinctrl_pin_desc *pdesc = keembay_pins + i;
1629                 struct keembay_mux_desc *mux = pdesc->drv_data;
1630
1631                 while (mux->name) {
1632                         struct function_desc *fdesc = keembay_funcs;
1633
1634                         while (fdesc->name) {
1635                                 if (!strcmp(mux->name, fdesc->name)) {
1636                                         fdesc->num_group_names++;
1637                                         break;
1638                                 }
1639
1640                                 fdesc++;
1641                         }
1642
1643                         if (!fdesc->name) {
1644                                 fdesc->name = mux->name;
1645                                 fdesc->num_group_names = 1;
1646                                 fdesc->data = &mux->mode;
1647                                 kpc->nfuncs++;
1648                         }
1649
1650                         mux++;
1651                 }
1652         }
1653
1654         /* Reallocate memory based on actual number of functions */
1655         new_funcs = krealloc(keembay_funcs, kpc->nfuncs * sizeof(*new_funcs), GFP_KERNEL);
1656         if (!new_funcs) {
1657                 kfree(keembay_funcs);
1658                 return -ENOMEM;
1659         }
1660
1661         return keembay_add_functions(kpc, new_funcs);
1662 }
1663
1664 static const struct keembay_pin_soc keembay_data = {
1665         .pins    = keembay_pins,
1666 };
1667
1668 static const struct of_device_id keembay_pinctrl_match[] = {
1669         { .compatible = "intel,keembay-pinctrl", .data = &keembay_data },
1670         { }
1671 };
1672 MODULE_DEVICE_TABLE(of, keembay_pinctrl_match);
1673
1674 static int keembay_pinctrl_probe(struct platform_device *pdev)
1675 {
1676         struct device *dev = &pdev->dev;
1677         struct keembay_pinctrl *kpc;
1678         int ret;
1679
1680         kpc = devm_kzalloc(dev, sizeof(*kpc), GFP_KERNEL);
1681         if (!kpc)
1682                 return -ENOMEM;
1683
1684         kpc->dev = dev;
1685         kpc->soc = device_get_match_data(dev);
1686
1687         kpc->base0 = devm_platform_ioremap_resource(pdev, 0);
1688         if (IS_ERR(kpc->base0))
1689                 return PTR_ERR(kpc->base0);
1690
1691         kpc->base1 = devm_platform_ioremap_resource(pdev, 1);
1692         if (IS_ERR(kpc->base1))
1693                 return PTR_ERR(kpc->base1);
1694
1695         raw_spin_lock_init(&kpc->lock);
1696
1697         ret = keembay_pinctrl_reg(kpc, dev);
1698         if (ret)
1699                 return ret;
1700
1701         ret = keembay_build_groups(kpc);
1702         if (ret)
1703                 return ret;
1704
1705         ret = keembay_build_functions(kpc);
1706         if (ret)
1707                 return ret;
1708
1709         ret = keembay_gpiochip_probe(kpc, pdev);
1710         if (ret)
1711                 return ret;
1712
1713         platform_set_drvdata(pdev, kpc);
1714
1715         return 0;
1716 }
1717
1718 static struct platform_driver keembay_pinctrl_driver = {
1719         .probe = keembay_pinctrl_probe,
1720         .driver = {
1721                 .name = "keembay-pinctrl",
1722                 .of_match_table = keembay_pinctrl_match,
1723         },
1724 };
1725 module_platform_driver(keembay_pinctrl_driver);
1726
1727 MODULE_AUTHOR("Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>");
1728 MODULE_AUTHOR("Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com>");
1729 MODULE_AUTHOR("Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>");
1730 MODULE_DESCRIPTION("Intel Keem Bay SoC pinctrl/GPIO driver");
1731 MODULE_LICENSE("GPL");