3 bool "Bit-banged ethernet MII management channel support"
5 config MV88E6352_SWITCH
6 bool "Marvell 88E6352 switch support"
9 bool "Ethernet PHY (physical media interface) support"
12 Enable Ethernet PHY (physical media interface) support.
16 config PHY_ADDR_ENABLE
17 bool "Limit phy address"
18 default y if ARCH_SUNXI
20 Select this if you want to control which phy address is used
25 default 1 if ARCH_SUNXI
28 The address of PHY on MII bus. Usually in range of 0 to 31.
32 bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support."
34 Enable support for Broadcom BCM53xx (RoboSwitch) Ethernet switches.
35 This currently supports BCM53125 and similar models.
44 hex "Bitmask of PHY ports"
48 config MV88E61XX_SWITCH
49 bool "Marvell MV88E61xx Ethernet switch PHY support."
53 config MV88E61XX_CPU_PORT
56 config MV88E61XX_PHY_PORTS
57 hex "Bitmask of PHY Ports"
59 config MV88E61XX_FIXED_PORTS
60 hex "Bitmask of PHYless serdes Ports"
62 endif # MV88E61XX_SWITCH
65 bool "Generic 10G PHY support"
67 menuconfig PHY_AQUANTIA
68 bool "Aquantia Ethernet PHYs support"
72 config PHY_AQUANTIA_UPLOAD_FW
73 bool "Aquantia firmware loading support"
75 depends on PHY_AQUANTIA
77 Aquantia PHYs use firmware which can be either loaded automatically
78 from storage directly attached to the phy or loaded by the boot loader
79 via MDIO commands. The firmware is loaded from a file, specified by
80 the PHY_AQUANTIA_FW_PART and PHY_AQUANTIA_FW_NAME options.
82 config PHY_AQUANTIA_FW_PART
83 string "Aquantia firmware partition"
84 depends on PHY_AQUANTIA_UPLOAD_FW
86 Partition containing the firmware file.
88 config PHY_AQUANTIA_FW_NAME
89 string "Aquantia firmware filename"
90 depends on PHY_AQUANTIA_UPLOAD_FW
95 bool "Atheros Ethernet PHYs support"
98 bool "Broadcom Ethernet PHYs support"
101 bool "Cortina Ethernet PHYs support"
103 config SYS_CORTINA_NO_FW_UPLOAD
104 bool "Cortina firmware loading support"
106 depends on PHY_CORTINA
108 Cortina phy has provision to store phy firmware in attached dedicated
109 EEPROM. And boards designed with such EEPROM does not require firmware
113 prompt "Location of the Cortina firmware"
114 default SYS_CORTINA_FW_IN_NOR
115 depends on PHY_CORTINA
117 config SYS_CORTINA_FW_IN_MMC
118 bool "Cortina firmware in MMC"
120 config SYS_CORTINA_FW_IN_NAND
121 bool "Cortina firmware in NAND flash"
123 config SYS_CORTINA_FW_IN_NOR
124 bool "Cortina firmware in NOR flash"
126 config SYS_CORTINA_FW_IN_REMOTE
127 bool "Cortina firmware in remote device"
129 config SYS_CORTINA_FW_IN_SPIFLASH
130 bool "Cortina firmware in SPI flash"
134 config PHY_CORTINA_ACCESS
135 bool "Cortina Access Ethernet PHYs support"
137 depends on CORTINA_NI_ENET
139 Cortina Access Ethernet PHYs init process
142 bool "Davicom Ethernet PHYs support"
145 bool "LSI TruePHY ET1011C support"
148 bool "LXT971 Ethernet PHY support"
151 bool "Marvell Ethernet PHYs support"
154 bool "Amlogic Meson GXL Internal PHY support"
157 bool "Micrel Ethernet PHYs support"
159 Enable support for the GbE PHYs manufactured by Micrel (now
160 a part of Microchip). This includes drivers for the KSZ804, KSZ8031,
161 KSZ8051, KSZ8081, KSZ8895, KSZ886x and KSZ8721 (if "Micrel KSZ8xxx
162 family support" is selected) and the KSZ9021 and KSZ9031 (if "Micrel
163 KSZ90x1 family support" is selected).
167 config PHY_MICREL_KSZ9021
169 select PHY_MICREL_KSZ90X1
171 config PHY_MICREL_KSZ9031
173 select PHY_MICREL_KSZ90X1
175 config PHY_MICREL_KSZ90X1
176 bool "Micrel KSZ90x1 family support"
179 Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If
180 enabled, the extended register read/write for KSZ90x1 PHYs
181 is supported through the 'mdio' command and any RGMII signal
182 delays configured in the device tree will be applied to the
183 PHY during initialization.
185 config PHY_MICREL_KSZ8XXX
186 bool "Micrel KSZ8xxx family support"
188 Enable support for the 8000 series 10/100 PHYs manufactured by Micrel
189 (now a part of Microchip). This includes drivers for the KSZ804,
190 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721.
195 bool "Microsemi Corp Ethernet PHYs support"
198 bool "National Semiconductor Ethernet PHYs support"
200 config PHY_NXP_C45_TJA11XX
201 tristate "NXP C45 TJA11XX PHYs"
203 Enable support for NXP C45 TJA11XX PHYs.
204 Currently supports only the TJA1103 PHY.
207 bool "Realtek Ethernet PHYs support"
209 config RTL8211E_PINE64_GIGABIT_FIX
210 bool "Fix gigabit throughput on some Pine64+ models"
211 depends on PHY_REALTEK
213 Configure the Realtek RTL8211E found on some Pine64+ models differently to
214 fix throughput on Gigabit links, turning off all internal delays in the
215 process. The settings that this touches are not documented in the CONFREG
216 section of the RTL8211E datasheet, but come from Realtek by way of the
217 Pine64 engineering team.
219 config RTL8211X_PHY_FORCE_MASTER
220 bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
221 depends on PHY_REALTEK
223 Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
224 This can work around link stability and data corruption issues on gigabit
225 links which can occur in slave mode on certain PHYs, e.g. on the
228 Please note that two directly connected devices (i.e. via crossover cable)
229 will not be able to establish a link between each other if they both force
230 master mode. Multiple devices forcing master mode when connected by a
231 network switch do not pose a problem as the switch configures its affected
232 ports into slave mode.
234 This option only affects gigabit links. If you must establish a direct
235 connection between two devices which both force master mode, try forcing
236 the link speed to 100MBit/s.
240 config RTL8211F_PHY_FORCE_EEE_RXC_ON
241 bool "Ethernet PHY RTL8211F: do not stop receiving the xMII clock during LPI"
242 depends on PHY_REALTEK
245 The IEEE 802.3az-2010 (EEE) standard provides a protocol to coordinate
246 transitions to/from a lower power consumption level (Low Power Idle
247 mode) based on link utilization. When no packets are being
248 transmitted, the system goes to Low Power Idle mode to save power.
250 Under particular circumstances this setting can cause issues where
251 the PHY is unable to transmit or receive any packet when in LPI mode.
252 The problem is caused when the PHY is configured to stop receiving
253 the xMII clock while it is signaling LPI. For some PHYs the bit
254 configuring this behavior is set by the Linux kernel, causing the
255 issue in U-Boot on reboot if the PHY retains the register value.
257 Default n, which means that the PHY state is not changed. To work
258 around the issues, change this setting to y.
260 config RTL8201F_PHY_S700_RMII_TIMINGS
261 bool "Ethernet PHY RTL8201F: adjust RMII Tx Interface timings"
262 depends on PHY_REALTEK
264 This provides an option to configure specific timing requirements (needed
265 for proper PHY operations) for the PHY module present on ACTION SEMI S700
266 based cubieboard7. Exact timing requiremnets seems to be SoC specific
267 (and it's undocumented) that comes from vendor code itself.
270 bool "Microchip(SMSC) Ethernet PHYs support"
272 config PHY_TERANETICS
273 bool "Teranetics Ethernet PHYs support"
276 bool "Texas Instruments Ethernet PHYs support"
278 Adds PHY registration support for TI PHYs.
280 config PHY_TI_DP83867
282 bool "Texas Instruments Ethernet DP83867 PHY support"
284 Adds support for the TI DP83867 1Gbit PHY.
286 config PHY_TI_GENERIC
288 bool "Texas Instruments Generic Ethernet PHYs support"
290 Adds support for Generic TI PHYs that don't need special handling but
291 the PHY name is associated with a PHY ID.
294 bool "Vitesse Ethernet PHYs support"
297 bool "Xilinx Ethernet PHYs support"
299 config PHY_XILINX_GMII2RGMII
300 bool "Xilinx GMII to RGMII Ethernet PHYs support"
303 This adds support for Xilinx GMII to RGMII IP core. This IP acts
304 as bridge between MAC connected over GMII and external phy that
305 is connected over RGMII interface.
308 bool "Fixed-Link PHY"
311 Fixed PHY is used for having a 'fixed-link' to another MAC with a direct
312 connection (MII, RGMII, ...).
313 There is nothing like autoneogation and so
314 on, the link is always up with fixed speed and fixed duplex-setting.
315 More information: doc/device-tree-bindings/net/fixed-link.txt
318 bool "NC-SI based PHY"