1 /*******************************************************************************
3 Intel PRO/1000 Linux driver
4 Copyright(c) 1999 - 2012 Intel Corporation.
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, write to the Free Software Foundation, Inc.,
17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
19 The full GNU General Public License is included in this distribution in
20 the file called "COPYING".
23 Linux NICS <linux.nics@intel.com>
24 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
25 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
27 *******************************************************************************/
29 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
31 #include <linux/module.h>
32 #include <linux/types.h>
33 #include <linux/init.h>
34 #include <linux/pci.h>
35 #include <linux/vmalloc.h>
36 #include <linux/pagemap.h>
37 #include <linux/delay.h>
38 #include <linux/netdevice.h>
39 #include <linux/interrupt.h>
40 #include <linux/tcp.h>
41 #include <linux/ipv6.h>
42 #include <linux/slab.h>
43 #include <net/checksum.h>
44 #include <net/ip6_checksum.h>
45 #include <linux/mii.h>
46 #include <linux/ethtool.h>
47 #include <linux/if_vlan.h>
48 #include <linux/cpu.h>
49 #include <linux/smp.h>
50 #include <linux/pm_qos.h>
51 #include <linux/pm_runtime.h>
52 #include <linux/aer.h>
53 #include <linux/prefetch.h>
57 #define DRV_EXTRAVERSION "-k"
59 #define DRV_VERSION "2.0.0" DRV_EXTRAVERSION
60 char e1000e_driver_name[] = "e1000e";
61 const char e1000e_driver_version[] = DRV_VERSION;
63 #define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK)
64 static int debug = -1;
65 module_param(debug, int, 0);
66 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
68 static void e1000e_disable_aspm(struct pci_dev *pdev, u16 state);
70 static const struct e1000_info *e1000_info_tbl[] = {
71 [board_82571] = &e1000_82571_info,
72 [board_82572] = &e1000_82572_info,
73 [board_82573] = &e1000_82573_info,
74 [board_82574] = &e1000_82574_info,
75 [board_82583] = &e1000_82583_info,
76 [board_80003es2lan] = &e1000_es2_info,
77 [board_ich8lan] = &e1000_ich8_info,
78 [board_ich9lan] = &e1000_ich9_info,
79 [board_ich10lan] = &e1000_ich10_info,
80 [board_pchlan] = &e1000_pch_info,
81 [board_pch2lan] = &e1000_pch2_info,
82 [board_pch_lpt] = &e1000_pch_lpt_info,
85 struct e1000_reg_info {
90 #define E1000_RDFH 0x02410 /* Rx Data FIFO Head - RW */
91 #define E1000_RDFT 0x02418 /* Rx Data FIFO Tail - RW */
92 #define E1000_RDFHS 0x02420 /* Rx Data FIFO Head Saved - RW */
93 #define E1000_RDFTS 0x02428 /* Rx Data FIFO Tail Saved - RW */
94 #define E1000_RDFPC 0x02430 /* Rx Data FIFO Packet Count - RW */
96 #define E1000_TDFH 0x03410 /* Tx Data FIFO Head - RW */
97 #define E1000_TDFT 0x03418 /* Tx Data FIFO Tail - RW */
98 #define E1000_TDFHS 0x03420 /* Tx Data FIFO Head Saved - RW */
99 #define E1000_TDFTS 0x03428 /* Tx Data FIFO Tail Saved - RW */
100 #define E1000_TDFPC 0x03430 /* Tx Data FIFO Packet Count - RW */
102 static const struct e1000_reg_info e1000_reg_info_tbl[] = {
104 /* General Registers */
105 {E1000_CTRL, "CTRL"},
106 {E1000_STATUS, "STATUS"},
107 {E1000_CTRL_EXT, "CTRL_EXT"},
109 /* Interrupt Registers */
113 {E1000_RCTL, "RCTL"},
114 {E1000_RDLEN(0), "RDLEN"},
115 {E1000_RDH(0), "RDH"},
116 {E1000_RDT(0), "RDT"},
117 {E1000_RDTR, "RDTR"},
118 {E1000_RXDCTL(0), "RXDCTL"},
120 {E1000_RDBAL(0), "RDBAL"},
121 {E1000_RDBAH(0), "RDBAH"},
122 {E1000_RDFH, "RDFH"},
123 {E1000_RDFT, "RDFT"},
124 {E1000_RDFHS, "RDFHS"},
125 {E1000_RDFTS, "RDFTS"},
126 {E1000_RDFPC, "RDFPC"},
129 {E1000_TCTL, "TCTL"},
130 {E1000_TDBAL(0), "TDBAL"},
131 {E1000_TDBAH(0), "TDBAH"},
132 {E1000_TDLEN(0), "TDLEN"},
133 {E1000_TDH(0), "TDH"},
134 {E1000_TDT(0), "TDT"},
135 {E1000_TIDV, "TIDV"},
136 {E1000_TXDCTL(0), "TXDCTL"},
137 {E1000_TADV, "TADV"},
138 {E1000_TARC(0), "TARC"},
139 {E1000_TDFH, "TDFH"},
140 {E1000_TDFT, "TDFT"},
141 {E1000_TDFHS, "TDFHS"},
142 {E1000_TDFTS, "TDFTS"},
143 {E1000_TDFPC, "TDFPC"},
145 /* List Terminator */
150 * e1000_regdump - register printout routine
152 static void e1000_regdump(struct e1000_hw *hw, struct e1000_reg_info *reginfo)
158 switch (reginfo->ofs) {
159 case E1000_RXDCTL(0):
160 for (n = 0; n < 2; n++)
161 regs[n] = __er32(hw, E1000_RXDCTL(n));
163 case E1000_TXDCTL(0):
164 for (n = 0; n < 2; n++)
165 regs[n] = __er32(hw, E1000_TXDCTL(n));
168 for (n = 0; n < 2; n++)
169 regs[n] = __er32(hw, E1000_TARC(n));
172 pr_info("%-15s %08x\n",
173 reginfo->name, __er32(hw, reginfo->ofs));
177 snprintf(rname, 16, "%s%s", reginfo->name, "[0-1]");
178 pr_info("%-15s %08x %08x\n", rname, regs[0], regs[1]);
182 * e1000e_dump - Print registers, Tx-ring and Rx-ring
184 static void e1000e_dump(struct e1000_adapter *adapter)
186 struct net_device *netdev = adapter->netdev;
187 struct e1000_hw *hw = &adapter->hw;
188 struct e1000_reg_info *reginfo;
189 struct e1000_ring *tx_ring = adapter->tx_ring;
190 struct e1000_tx_desc *tx_desc;
195 struct e1000_buffer *buffer_info;
196 struct e1000_ring *rx_ring = adapter->rx_ring;
197 union e1000_rx_desc_packet_split *rx_desc_ps;
198 union e1000_rx_desc_extended *rx_desc;
208 if (!netif_msg_hw(adapter))
211 /* Print netdevice Info */
213 dev_info(&adapter->pdev->dev, "Net device Info\n");
214 pr_info("Device Name state trans_start last_rx\n");
215 pr_info("%-15s %016lX %016lX %016lX\n",
216 netdev->name, netdev->state, netdev->trans_start,
220 /* Print Registers */
221 dev_info(&adapter->pdev->dev, "Register Dump\n");
222 pr_info(" Register Name Value\n");
223 for (reginfo = (struct e1000_reg_info *)e1000_reg_info_tbl;
224 reginfo->name; reginfo++) {
225 e1000_regdump(hw, reginfo);
228 /* Print Tx Ring Summary */
229 if (!netdev || !netif_running(netdev))
232 dev_info(&adapter->pdev->dev, "Tx Ring Summary\n");
233 pr_info("Queue [NTU] [NTC] [bi(ntc)->dma ] leng ntw timestamp\n");
234 buffer_info = &tx_ring->buffer_info[tx_ring->next_to_clean];
235 pr_info(" %5d %5X %5X %016llX %04X %3X %016llX\n",
236 0, tx_ring->next_to_use, tx_ring->next_to_clean,
237 (unsigned long long)buffer_info->dma,
239 buffer_info->next_to_watch,
240 (unsigned long long)buffer_info->time_stamp);
243 if (!netif_msg_tx_done(adapter))
244 goto rx_ring_summary;
246 dev_info(&adapter->pdev->dev, "Tx Ring Dump\n");
248 /* Transmit Descriptor Formats - DEXT[29] is 0 (Legacy) or 1 (Extended)
250 * Legacy Transmit Descriptor
251 * +--------------------------------------------------------------+
252 * 0 | Buffer Address [63:0] (Reserved on Write Back) |
253 * +--------------------------------------------------------------+
254 * 8 | Special | CSS | Status | CMD | CSO | Length |
255 * +--------------------------------------------------------------+
256 * 63 48 47 36 35 32 31 24 23 16 15 0
258 * Extended Context Descriptor (DTYP=0x0) for TSO or checksum offload
259 * 63 48 47 40 39 32 31 16 15 8 7 0
260 * +----------------------------------------------------------------+
261 * 0 | TUCSE | TUCS0 | TUCSS | IPCSE | IPCS0 | IPCSS |
262 * +----------------------------------------------------------------+
263 * 8 | MSS | HDRLEN | RSV | STA | TUCMD | DTYP | PAYLEN |
264 * +----------------------------------------------------------------+
265 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0
267 * Extended Data Descriptor (DTYP=0x1)
268 * +----------------------------------------------------------------+
269 * 0 | Buffer Address [63:0] |
270 * +----------------------------------------------------------------+
271 * 8 | VLAN tag | POPTS | Rsvd | Status | Command | DTYP | DTALEN |
272 * +----------------------------------------------------------------+
273 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0
275 pr_info("Tl[desc] [address 63:0 ] [SpeCssSCmCsLen] [bi->dma ] leng ntw timestamp bi->skb <-- Legacy format\n");
276 pr_info("Tc[desc] [Ce CoCsIpceCoS] [MssHlRSCm0Plen] [bi->dma ] leng ntw timestamp bi->skb <-- Ext Context format\n");
277 pr_info("Td[desc] [address 63:0 ] [VlaPoRSCm1Dlen] [bi->dma ] leng ntw timestamp bi->skb <-- Ext Data format\n");
278 for (i = 0; tx_ring->desc && (i < tx_ring->count); i++) {
279 const char *next_desc;
280 tx_desc = E1000_TX_DESC(*tx_ring, i);
281 buffer_info = &tx_ring->buffer_info[i];
282 u0 = (struct my_u0 *)tx_desc;
283 if (i == tx_ring->next_to_use && i == tx_ring->next_to_clean)
284 next_desc = " NTC/U";
285 else if (i == tx_ring->next_to_use)
287 else if (i == tx_ring->next_to_clean)
291 pr_info("T%c[0x%03X] %016llX %016llX %016llX %04X %3X %016llX %p%s\n",
292 (!(le64_to_cpu(u0->b) & (1 << 29)) ? 'l' :
293 ((le64_to_cpu(u0->b) & (1 << 20)) ? 'd' : 'c')),
295 (unsigned long long)le64_to_cpu(u0->a),
296 (unsigned long long)le64_to_cpu(u0->b),
297 (unsigned long long)buffer_info->dma,
298 buffer_info->length, buffer_info->next_to_watch,
299 (unsigned long long)buffer_info->time_stamp,
300 buffer_info->skb, next_desc);
302 if (netif_msg_pktdata(adapter) && buffer_info->dma != 0)
303 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_ADDRESS,
304 16, 1, phys_to_virt(buffer_info->dma),
305 buffer_info->length, true);
308 /* Print Rx Ring Summary */
310 dev_info(&adapter->pdev->dev, "Rx Ring Summary\n");
311 pr_info("Queue [NTU] [NTC]\n");
312 pr_info(" %5d %5X %5X\n",
313 0, rx_ring->next_to_use, rx_ring->next_to_clean);
316 if (!netif_msg_rx_status(adapter))
319 dev_info(&adapter->pdev->dev, "Rx Ring Dump\n");
320 switch (adapter->rx_ps_pages) {
324 /* [Extended] Packet Split Receive Descriptor Format
326 * +-----------------------------------------------------+
327 * 0 | Buffer Address 0 [63:0] |
328 * +-----------------------------------------------------+
329 * 8 | Buffer Address 1 [63:0] |
330 * +-----------------------------------------------------+
331 * 16 | Buffer Address 2 [63:0] |
332 * +-----------------------------------------------------+
333 * 24 | Buffer Address 3 [63:0] |
334 * +-----------------------------------------------------+
336 pr_info("R [desc] [buffer 0 63:0 ] [buffer 1 63:0 ] [buffer 2 63:0 ] [buffer 3 63:0 ] [bi->dma ] [bi->skb] <-- Ext Pkt Split format\n");
337 /* [Extended] Receive Descriptor (Write-Back) Format
339 * 63 48 47 32 31 13 12 8 7 4 3 0
340 * +------------------------------------------------------+
341 * 0 | Packet | IP | Rsvd | MRQ | Rsvd | MRQ RSS |
342 * | Checksum | Ident | | Queue | | Type |
343 * +------------------------------------------------------+
344 * 8 | VLAN Tag | Length | Extended Error | Extended Status |
345 * +------------------------------------------------------+
346 * 63 48 47 32 31 20 19 0
348 pr_info("RWB[desc] [ck ipid mrqhsh] [vl l0 ee es] [ l3 l2 l1 hs] [reserved ] ---------------- [bi->skb] <-- Ext Rx Write-Back format\n");
349 for (i = 0; i < rx_ring->count; i++) {
350 const char *next_desc;
351 buffer_info = &rx_ring->buffer_info[i];
352 rx_desc_ps = E1000_RX_DESC_PS(*rx_ring, i);
353 u1 = (struct my_u1 *)rx_desc_ps;
355 le32_to_cpu(rx_desc_ps->wb.middle.status_error);
357 if (i == rx_ring->next_to_use)
359 else if (i == rx_ring->next_to_clean)
364 if (staterr & E1000_RXD_STAT_DD) {
365 /* Descriptor Done */
366 pr_info("%s[0x%03X] %016llX %016llX %016llX %016llX ---------------- %p%s\n",
368 (unsigned long long)le64_to_cpu(u1->a),
369 (unsigned long long)le64_to_cpu(u1->b),
370 (unsigned long long)le64_to_cpu(u1->c),
371 (unsigned long long)le64_to_cpu(u1->d),
372 buffer_info->skb, next_desc);
374 pr_info("%s[0x%03X] %016llX %016llX %016llX %016llX %016llX %p%s\n",
376 (unsigned long long)le64_to_cpu(u1->a),
377 (unsigned long long)le64_to_cpu(u1->b),
378 (unsigned long long)le64_to_cpu(u1->c),
379 (unsigned long long)le64_to_cpu(u1->d),
380 (unsigned long long)buffer_info->dma,
381 buffer_info->skb, next_desc);
383 if (netif_msg_pktdata(adapter))
384 print_hex_dump(KERN_INFO, "",
385 DUMP_PREFIX_ADDRESS, 16, 1,
386 phys_to_virt(buffer_info->dma),
387 adapter->rx_ps_bsize0, true);
393 /* Extended Receive Descriptor (Read) Format
395 * +-----------------------------------------------------+
396 * 0 | Buffer Address [63:0] |
397 * +-----------------------------------------------------+
399 * +-----------------------------------------------------+
401 pr_info("R [desc] [buf addr 63:0 ] [reserved 63:0 ] [bi->dma ] [bi->skb] <-- Ext (Read) format\n");
402 /* Extended Receive Descriptor (Write-Back) Format
404 * 63 48 47 32 31 24 23 4 3 0
405 * +------------------------------------------------------+
407 * 0 +-------------------+ Rsvd | Reserved | MRQ RSS |
408 * | Packet | IP | | | Type |
409 * | Checksum | Ident | | | |
410 * +------------------------------------------------------+
411 * 8 | VLAN Tag | Length | Extended Error | Extended Status |
412 * +------------------------------------------------------+
413 * 63 48 47 32 31 20 19 0
415 pr_info("RWB[desc] [cs ipid mrq] [vt ln xe xs] [bi->skb] <-- Ext (Write-Back) format\n");
417 for (i = 0; i < rx_ring->count; i++) {
418 const char *next_desc;
420 buffer_info = &rx_ring->buffer_info[i];
421 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
422 u1 = (struct my_u1 *)rx_desc;
423 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
425 if (i == rx_ring->next_to_use)
427 else if (i == rx_ring->next_to_clean)
432 if (staterr & E1000_RXD_STAT_DD) {
433 /* Descriptor Done */
434 pr_info("%s[0x%03X] %016llX %016llX ---------------- %p%s\n",
436 (unsigned long long)le64_to_cpu(u1->a),
437 (unsigned long long)le64_to_cpu(u1->b),
438 buffer_info->skb, next_desc);
440 pr_info("%s[0x%03X] %016llX %016llX %016llX %p%s\n",
442 (unsigned long long)le64_to_cpu(u1->a),
443 (unsigned long long)le64_to_cpu(u1->b),
444 (unsigned long long)buffer_info->dma,
445 buffer_info->skb, next_desc);
447 if (netif_msg_pktdata(adapter))
448 print_hex_dump(KERN_INFO, "",
449 DUMP_PREFIX_ADDRESS, 16,
453 adapter->rx_buffer_len,
461 * e1000_desc_unused - calculate if we have unused descriptors
463 static int e1000_desc_unused(struct e1000_ring *ring)
465 if (ring->next_to_clean > ring->next_to_use)
466 return ring->next_to_clean - ring->next_to_use - 1;
468 return ring->count + ring->next_to_clean - ring->next_to_use - 1;
472 * e1000_receive_skb - helper function to handle Rx indications
473 * @adapter: board private structure
474 * @status: descriptor status field as written by hardware
475 * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
476 * @skb: pointer to sk_buff to be indicated to stack
478 static void e1000_receive_skb(struct e1000_adapter *adapter,
479 struct net_device *netdev, struct sk_buff *skb,
480 u8 status, __le16 vlan)
482 u16 tag = le16_to_cpu(vlan);
483 skb->protocol = eth_type_trans(skb, netdev);
485 if (status & E1000_RXD_STAT_VP)
486 __vlan_hwaccel_put_tag(skb, tag);
488 napi_gro_receive(&adapter->napi, skb);
492 * e1000_rx_checksum - Receive Checksum Offload
493 * @adapter: board private structure
494 * @status_err: receive descriptor status and error fields
495 * @csum: receive descriptor csum field
496 * @sk_buff: socket buffer with received data
498 static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
501 u16 status = (u16)status_err;
502 u8 errors = (u8)(status_err >> 24);
504 skb_checksum_none_assert(skb);
506 /* Rx checksum disabled */
507 if (!(adapter->netdev->features & NETIF_F_RXCSUM))
510 /* Ignore Checksum bit is set */
511 if (status & E1000_RXD_STAT_IXSM)
514 /* TCP/UDP checksum error bit or IP checksum error bit is set */
515 if (errors & (E1000_RXD_ERR_TCPE | E1000_RXD_ERR_IPE)) {
516 /* let the stack verify checksum errors */
517 adapter->hw_csum_err++;
521 /* TCP/UDP Checksum has not been calculated */
522 if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS)))
525 /* It must be a TCP or UDP packet with a valid checksum */
526 skb->ip_summed = CHECKSUM_UNNECESSARY;
527 adapter->hw_csum_good++;
530 static void e1000e_update_rdt_wa(struct e1000_ring *rx_ring, unsigned int i)
532 struct e1000_adapter *adapter = rx_ring->adapter;
533 struct e1000_hw *hw = &adapter->hw;
534 s32 ret_val = __ew32_prepare(hw);
536 writel(i, rx_ring->tail);
538 if (unlikely(!ret_val && (i != readl(rx_ring->tail)))) {
539 u32 rctl = er32(RCTL);
540 ew32(RCTL, rctl & ~E1000_RCTL_EN);
541 e_err("ME firmware caused invalid RDT - resetting\n");
542 schedule_work(&adapter->reset_task);
546 static void e1000e_update_tdt_wa(struct e1000_ring *tx_ring, unsigned int i)
548 struct e1000_adapter *adapter = tx_ring->adapter;
549 struct e1000_hw *hw = &adapter->hw;
550 s32 ret_val = __ew32_prepare(hw);
552 writel(i, tx_ring->tail);
554 if (unlikely(!ret_val && (i != readl(tx_ring->tail)))) {
555 u32 tctl = er32(TCTL);
556 ew32(TCTL, tctl & ~E1000_TCTL_EN);
557 e_err("ME firmware caused invalid TDT - resetting\n");
558 schedule_work(&adapter->reset_task);
563 * e1000_alloc_rx_buffers - Replace used receive buffers
564 * @rx_ring: Rx descriptor ring
566 static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring,
567 int cleaned_count, gfp_t gfp)
569 struct e1000_adapter *adapter = rx_ring->adapter;
570 struct net_device *netdev = adapter->netdev;
571 struct pci_dev *pdev = adapter->pdev;
572 union e1000_rx_desc_extended *rx_desc;
573 struct e1000_buffer *buffer_info;
576 unsigned int bufsz = adapter->rx_buffer_len;
578 i = rx_ring->next_to_use;
579 buffer_info = &rx_ring->buffer_info[i];
581 while (cleaned_count--) {
582 skb = buffer_info->skb;
588 skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp);
590 /* Better luck next round */
591 adapter->alloc_rx_buff_failed++;
595 buffer_info->skb = skb;
597 buffer_info->dma = dma_map_single(&pdev->dev, skb->data,
598 adapter->rx_buffer_len,
600 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
601 dev_err(&pdev->dev, "Rx DMA map failed\n");
602 adapter->rx_dma_failed++;
606 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
607 rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma);
609 if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) {
611 * Force memory writes to complete before letting h/w
612 * know there are new descriptors to fetch. (Only
613 * applicable for weak-ordered memory model archs,
617 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
618 e1000e_update_rdt_wa(rx_ring, i);
620 writel(i, rx_ring->tail);
623 if (i == rx_ring->count)
625 buffer_info = &rx_ring->buffer_info[i];
628 rx_ring->next_to_use = i;
632 * e1000_alloc_rx_buffers_ps - Replace used receive buffers; packet split
633 * @rx_ring: Rx descriptor ring
635 static void e1000_alloc_rx_buffers_ps(struct e1000_ring *rx_ring,
636 int cleaned_count, gfp_t gfp)
638 struct e1000_adapter *adapter = rx_ring->adapter;
639 struct net_device *netdev = adapter->netdev;
640 struct pci_dev *pdev = adapter->pdev;
641 union e1000_rx_desc_packet_split *rx_desc;
642 struct e1000_buffer *buffer_info;
643 struct e1000_ps_page *ps_page;
647 i = rx_ring->next_to_use;
648 buffer_info = &rx_ring->buffer_info[i];
650 while (cleaned_count--) {
651 rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
653 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
654 ps_page = &buffer_info->ps_pages[j];
655 if (j >= adapter->rx_ps_pages) {
656 /* all unused desc entries get hw null ptr */
657 rx_desc->read.buffer_addr[j + 1] =
661 if (!ps_page->page) {
662 ps_page->page = alloc_page(gfp);
663 if (!ps_page->page) {
664 adapter->alloc_rx_buff_failed++;
667 ps_page->dma = dma_map_page(&pdev->dev,
671 if (dma_mapping_error(&pdev->dev,
673 dev_err(&adapter->pdev->dev,
674 "Rx DMA page map failed\n");
675 adapter->rx_dma_failed++;
680 * Refresh the desc even if buffer_addrs
681 * didn't change because each write-back
684 rx_desc->read.buffer_addr[j + 1] =
685 cpu_to_le64(ps_page->dma);
688 skb = __netdev_alloc_skb_ip_align(netdev,
689 adapter->rx_ps_bsize0,
693 adapter->alloc_rx_buff_failed++;
697 buffer_info->skb = skb;
698 buffer_info->dma = dma_map_single(&pdev->dev, skb->data,
699 adapter->rx_ps_bsize0,
701 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
702 dev_err(&pdev->dev, "Rx DMA map failed\n");
703 adapter->rx_dma_failed++;
705 dev_kfree_skb_any(skb);
706 buffer_info->skb = NULL;
710 rx_desc->read.buffer_addr[0] = cpu_to_le64(buffer_info->dma);
712 if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) {
714 * Force memory writes to complete before letting h/w
715 * know there are new descriptors to fetch. (Only
716 * applicable for weak-ordered memory model archs,
720 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
721 e1000e_update_rdt_wa(rx_ring, i << 1);
723 writel(i << 1, rx_ring->tail);
727 if (i == rx_ring->count)
729 buffer_info = &rx_ring->buffer_info[i];
733 rx_ring->next_to_use = i;
737 * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers
738 * @rx_ring: Rx descriptor ring
739 * @cleaned_count: number of buffers to allocate this pass
742 static void e1000_alloc_jumbo_rx_buffers(struct e1000_ring *rx_ring,
743 int cleaned_count, gfp_t gfp)
745 struct e1000_adapter *adapter = rx_ring->adapter;
746 struct net_device *netdev = adapter->netdev;
747 struct pci_dev *pdev = adapter->pdev;
748 union e1000_rx_desc_extended *rx_desc;
749 struct e1000_buffer *buffer_info;
752 unsigned int bufsz = 256 - 16 /* for skb_reserve */;
754 i = rx_ring->next_to_use;
755 buffer_info = &rx_ring->buffer_info[i];
757 while (cleaned_count--) {
758 skb = buffer_info->skb;
764 skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp);
765 if (unlikely(!skb)) {
766 /* Better luck next round */
767 adapter->alloc_rx_buff_failed++;
771 buffer_info->skb = skb;
773 /* allocate a new page if necessary */
774 if (!buffer_info->page) {
775 buffer_info->page = alloc_page(gfp);
776 if (unlikely(!buffer_info->page)) {
777 adapter->alloc_rx_buff_failed++;
782 if (!buffer_info->dma)
783 buffer_info->dma = dma_map_page(&pdev->dev,
784 buffer_info->page, 0,
788 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
789 rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma);
791 if (unlikely(++i == rx_ring->count))
793 buffer_info = &rx_ring->buffer_info[i];
796 if (likely(rx_ring->next_to_use != i)) {
797 rx_ring->next_to_use = i;
798 if (unlikely(i-- == 0))
799 i = (rx_ring->count - 1);
801 /* Force memory writes to complete before letting h/w
802 * know there are new descriptors to fetch. (Only
803 * applicable for weak-ordered memory model archs,
806 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
807 e1000e_update_rdt_wa(rx_ring, i);
809 writel(i, rx_ring->tail);
813 static inline void e1000_rx_hash(struct net_device *netdev, __le32 rss,
816 if (netdev->features & NETIF_F_RXHASH)
817 skb->rxhash = le32_to_cpu(rss);
821 * e1000_clean_rx_irq - Send received data up the network stack
822 * @rx_ring: Rx descriptor ring
824 * the return value indicates whether actual cleaning was done, there
825 * is no guarantee that everything was cleaned
827 static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,
830 struct e1000_adapter *adapter = rx_ring->adapter;
831 struct net_device *netdev = adapter->netdev;
832 struct pci_dev *pdev = adapter->pdev;
833 struct e1000_hw *hw = &adapter->hw;
834 union e1000_rx_desc_extended *rx_desc, *next_rxd;
835 struct e1000_buffer *buffer_info, *next_buffer;
838 int cleaned_count = 0;
839 bool cleaned = false;
840 unsigned int total_rx_bytes = 0, total_rx_packets = 0;
842 i = rx_ring->next_to_clean;
843 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
844 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
845 buffer_info = &rx_ring->buffer_info[i];
847 while (staterr & E1000_RXD_STAT_DD) {
850 if (*work_done >= work_to_do)
853 rmb(); /* read descriptor and rx_buffer_info after status DD */
855 skb = buffer_info->skb;
856 buffer_info->skb = NULL;
858 prefetch(skb->data - NET_IP_ALIGN);
861 if (i == rx_ring->count)
863 next_rxd = E1000_RX_DESC_EXT(*rx_ring, i);
866 next_buffer = &rx_ring->buffer_info[i];
870 dma_unmap_single(&pdev->dev,
872 adapter->rx_buffer_len,
874 buffer_info->dma = 0;
876 length = le16_to_cpu(rx_desc->wb.upper.length);
879 * !EOP means multiple descriptors were used to store a single
880 * packet, if that's the case we need to toss it. In fact, we
881 * need to toss every packet with the EOP bit clear and the
882 * next frame that _does_ have the EOP bit set, as it is by
883 * definition only a frame fragment
885 if (unlikely(!(staterr & E1000_RXD_STAT_EOP)))
886 adapter->flags2 |= FLAG2_IS_DISCARDING;
888 if (adapter->flags2 & FLAG2_IS_DISCARDING) {
889 /* All receives must fit into a single buffer */
890 e_dbg("Receive packet consumed multiple buffers\n");
892 buffer_info->skb = skb;
893 if (staterr & E1000_RXD_STAT_EOP)
894 adapter->flags2 &= ~FLAG2_IS_DISCARDING;
898 if (unlikely((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) &&
899 !(netdev->features & NETIF_F_RXALL))) {
901 buffer_info->skb = skb;
905 /* adjust length to remove Ethernet CRC */
906 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) {
907 /* If configured to store CRC, don't subtract FCS,
908 * but keep the FCS bytes out of the total_rx_bytes
911 if (netdev->features & NETIF_F_RXFCS)
917 total_rx_bytes += length;
921 * code added for copybreak, this should improve
922 * performance for small packets with large amounts
923 * of reassembly being done in the stack
925 if (length < copybreak) {
926 struct sk_buff *new_skb =
927 netdev_alloc_skb_ip_align(netdev, length);
929 skb_copy_to_linear_data_offset(new_skb,
935 /* save the skb in buffer_info as good */
936 buffer_info->skb = skb;
939 /* else just continue with the old one */
941 /* end copybreak code */
942 skb_put(skb, length);
944 /* Receive Checksum Offload */
945 e1000_rx_checksum(adapter, staterr, skb);
947 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb);
949 e1000_receive_skb(adapter, netdev, skb, staterr,
950 rx_desc->wb.upper.vlan);
953 rx_desc->wb.upper.status_error &= cpu_to_le32(~0xFF);
955 /* return some buffers to hardware, one at a time is too slow */
956 if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
957 adapter->alloc_rx_buf(rx_ring, cleaned_count,
962 /* use prefetched values */
964 buffer_info = next_buffer;
966 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
968 rx_ring->next_to_clean = i;
970 cleaned_count = e1000_desc_unused(rx_ring);
972 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC);
974 adapter->total_rx_bytes += total_rx_bytes;
975 adapter->total_rx_packets += total_rx_packets;
979 static void e1000_put_txbuf(struct e1000_ring *tx_ring,
980 struct e1000_buffer *buffer_info)
982 struct e1000_adapter *adapter = tx_ring->adapter;
984 if (buffer_info->dma) {
985 if (buffer_info->mapped_as_page)
986 dma_unmap_page(&adapter->pdev->dev, buffer_info->dma,
987 buffer_info->length, DMA_TO_DEVICE);
989 dma_unmap_single(&adapter->pdev->dev, buffer_info->dma,
990 buffer_info->length, DMA_TO_DEVICE);
991 buffer_info->dma = 0;
993 if (buffer_info->skb) {
994 dev_kfree_skb_any(buffer_info->skb);
995 buffer_info->skb = NULL;
997 buffer_info->time_stamp = 0;
1000 static void e1000_print_hw_hang(struct work_struct *work)
1002 struct e1000_adapter *adapter = container_of(work,
1003 struct e1000_adapter,
1005 struct net_device *netdev = adapter->netdev;
1006 struct e1000_ring *tx_ring = adapter->tx_ring;
1007 unsigned int i = tx_ring->next_to_clean;
1008 unsigned int eop = tx_ring->buffer_info[i].next_to_watch;
1009 struct e1000_tx_desc *eop_desc = E1000_TX_DESC(*tx_ring, eop);
1010 struct e1000_hw *hw = &adapter->hw;
1011 u16 phy_status, phy_1000t_status, phy_ext_status;
1014 if (test_bit(__E1000_DOWN, &adapter->state))
1017 if (!adapter->tx_hang_recheck &&
1018 (adapter->flags2 & FLAG2_DMA_BURST)) {
1020 * May be block on write-back, flush and detect again
1021 * flush pending descriptor writebacks to memory
1023 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
1024 /* execute the writes immediately */
1027 * Due to rare timing issues, write to TIDV again to ensure
1028 * the write is successful
1030 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
1031 /* execute the writes immediately */
1033 adapter->tx_hang_recheck = true;
1036 /* Real hang detected */
1037 adapter->tx_hang_recheck = false;
1038 netif_stop_queue(netdev);
1040 e1e_rphy(hw, PHY_STATUS, &phy_status);
1041 e1e_rphy(hw, PHY_1000T_STATUS, &phy_1000t_status);
1042 e1e_rphy(hw, PHY_EXT_STATUS, &phy_ext_status);
1044 pci_read_config_word(adapter->pdev, PCI_STATUS, &pci_status);
1046 /* detected Hardware unit hang */
1047 e_err("Detected Hardware Unit Hang:\n"
1050 " next_to_use <%x>\n"
1051 " next_to_clean <%x>\n"
1052 "buffer_info[next_to_clean]:\n"
1053 " time_stamp <%lx>\n"
1054 " next_to_watch <%x>\n"
1056 " next_to_watch.status <%x>\n"
1059 "PHY 1000BASE-T Status <%x>\n"
1060 "PHY Extended Status <%x>\n"
1061 "PCI Status <%x>\n",
1062 readl(tx_ring->head),
1063 readl(tx_ring->tail),
1064 tx_ring->next_to_use,
1065 tx_ring->next_to_clean,
1066 tx_ring->buffer_info[eop].time_stamp,
1069 eop_desc->upper.fields.status,
1076 /* Suggest workaround for known h/w issue */
1077 if ((hw->mac.type == e1000_pchlan) && (er32(CTRL) & E1000_CTRL_TFCE))
1078 e_err("Try turning off Tx pause (flow control) via ethtool\n");
1082 * e1000_clean_tx_irq - Reclaim resources after transmit completes
1083 * @tx_ring: Tx descriptor ring
1085 * the return value indicates whether actual cleaning was done, there
1086 * is no guarantee that everything was cleaned
1088 static bool e1000_clean_tx_irq(struct e1000_ring *tx_ring)
1090 struct e1000_adapter *adapter = tx_ring->adapter;
1091 struct net_device *netdev = adapter->netdev;
1092 struct e1000_hw *hw = &adapter->hw;
1093 struct e1000_tx_desc *tx_desc, *eop_desc;
1094 struct e1000_buffer *buffer_info;
1095 unsigned int i, eop;
1096 unsigned int count = 0;
1097 unsigned int total_tx_bytes = 0, total_tx_packets = 0;
1098 unsigned int bytes_compl = 0, pkts_compl = 0;
1100 i = tx_ring->next_to_clean;
1101 eop = tx_ring->buffer_info[i].next_to_watch;
1102 eop_desc = E1000_TX_DESC(*tx_ring, eop);
1104 while ((eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) &&
1105 (count < tx_ring->count)) {
1106 bool cleaned = false;
1107 rmb(); /* read buffer_info after eop_desc */
1108 for (; !cleaned; count++) {
1109 tx_desc = E1000_TX_DESC(*tx_ring, i);
1110 buffer_info = &tx_ring->buffer_info[i];
1111 cleaned = (i == eop);
1114 total_tx_packets += buffer_info->segs;
1115 total_tx_bytes += buffer_info->bytecount;
1116 if (buffer_info->skb) {
1117 bytes_compl += buffer_info->skb->len;
1122 e1000_put_txbuf(tx_ring, buffer_info);
1123 tx_desc->upper.data = 0;
1126 if (i == tx_ring->count)
1130 if (i == tx_ring->next_to_use)
1132 eop = tx_ring->buffer_info[i].next_to_watch;
1133 eop_desc = E1000_TX_DESC(*tx_ring, eop);
1136 tx_ring->next_to_clean = i;
1138 netdev_completed_queue(netdev, pkts_compl, bytes_compl);
1140 #define TX_WAKE_THRESHOLD 32
1141 if (count && netif_carrier_ok(netdev) &&
1142 e1000_desc_unused(tx_ring) >= TX_WAKE_THRESHOLD) {
1143 /* Make sure that anybody stopping the queue after this
1144 * sees the new next_to_clean.
1148 if (netif_queue_stopped(netdev) &&
1149 !(test_bit(__E1000_DOWN, &adapter->state))) {
1150 netif_wake_queue(netdev);
1151 ++adapter->restart_queue;
1155 if (adapter->detect_tx_hung) {
1157 * Detect a transmit hang in hardware, this serializes the
1158 * check with the clearing of time_stamp and movement of i
1160 adapter->detect_tx_hung = false;
1161 if (tx_ring->buffer_info[i].time_stamp &&
1162 time_after(jiffies, tx_ring->buffer_info[i].time_stamp
1163 + (adapter->tx_timeout_factor * HZ)) &&
1164 !(er32(STATUS) & E1000_STATUS_TXOFF))
1165 schedule_work(&adapter->print_hang_task);
1167 adapter->tx_hang_recheck = false;
1169 adapter->total_tx_bytes += total_tx_bytes;
1170 adapter->total_tx_packets += total_tx_packets;
1171 return count < tx_ring->count;
1175 * e1000_clean_rx_irq_ps - Send received data up the network stack; packet split
1176 * @rx_ring: Rx descriptor ring
1178 * the return value indicates whether actual cleaning was done, there
1179 * is no guarantee that everything was cleaned
1181 static bool e1000_clean_rx_irq_ps(struct e1000_ring *rx_ring, int *work_done,
1184 struct e1000_adapter *adapter = rx_ring->adapter;
1185 struct e1000_hw *hw = &adapter->hw;
1186 union e1000_rx_desc_packet_split *rx_desc, *next_rxd;
1187 struct net_device *netdev = adapter->netdev;
1188 struct pci_dev *pdev = adapter->pdev;
1189 struct e1000_buffer *buffer_info, *next_buffer;
1190 struct e1000_ps_page *ps_page;
1191 struct sk_buff *skb;
1193 u32 length, staterr;
1194 int cleaned_count = 0;
1195 bool cleaned = false;
1196 unsigned int total_rx_bytes = 0, total_rx_packets = 0;
1198 i = rx_ring->next_to_clean;
1199 rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
1200 staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
1201 buffer_info = &rx_ring->buffer_info[i];
1203 while (staterr & E1000_RXD_STAT_DD) {
1204 if (*work_done >= work_to_do)
1207 skb = buffer_info->skb;
1208 rmb(); /* read descriptor and rx_buffer_info after status DD */
1210 /* in the packet split case this is header only */
1211 prefetch(skb->data - NET_IP_ALIGN);
1214 if (i == rx_ring->count)
1216 next_rxd = E1000_RX_DESC_PS(*rx_ring, i);
1219 next_buffer = &rx_ring->buffer_info[i];
1223 dma_unmap_single(&pdev->dev, buffer_info->dma,
1224 adapter->rx_ps_bsize0, DMA_FROM_DEVICE);
1225 buffer_info->dma = 0;
1227 /* see !EOP comment in other Rx routine */
1228 if (!(staterr & E1000_RXD_STAT_EOP))
1229 adapter->flags2 |= FLAG2_IS_DISCARDING;
1231 if (adapter->flags2 & FLAG2_IS_DISCARDING) {
1232 e_dbg("Packet Split buffers didn't pick up the full packet\n");
1233 dev_kfree_skb_irq(skb);
1234 if (staterr & E1000_RXD_STAT_EOP)
1235 adapter->flags2 &= ~FLAG2_IS_DISCARDING;
1239 if (unlikely((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) &&
1240 !(netdev->features & NETIF_F_RXALL))) {
1241 dev_kfree_skb_irq(skb);
1245 length = le16_to_cpu(rx_desc->wb.middle.length0);
1248 e_dbg("Last part of the packet spanning multiple descriptors\n");
1249 dev_kfree_skb_irq(skb);
1254 skb_put(skb, length);
1258 * this looks ugly, but it seems compiler issues make
1259 * it more efficient than reusing j
1261 int l1 = le16_to_cpu(rx_desc->wb.upper.length[0]);
1264 * page alloc/put takes too long and effects small
1265 * packet throughput, so unsplit small packets and
1266 * save the alloc/put only valid in softirq (napi)
1267 * context to call kmap_*
1269 if (l1 && (l1 <= copybreak) &&
1270 ((length + l1) <= adapter->rx_ps_bsize0)) {
1273 ps_page = &buffer_info->ps_pages[0];
1276 * there is no documentation about how to call
1277 * kmap_atomic, so we can't hold the mapping
1280 dma_sync_single_for_cpu(&pdev->dev,
1284 vaddr = kmap_atomic(ps_page->page);
1285 memcpy(skb_tail_pointer(skb), vaddr, l1);
1286 kunmap_atomic(vaddr);
1287 dma_sync_single_for_device(&pdev->dev,
1292 /* remove the CRC */
1293 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) {
1294 if (!(netdev->features & NETIF_F_RXFCS))
1303 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
1304 length = le16_to_cpu(rx_desc->wb.upper.length[j]);
1308 ps_page = &buffer_info->ps_pages[j];
1309 dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE,
1312 skb_fill_page_desc(skb, j, ps_page->page, 0, length);
1313 ps_page->page = NULL;
1315 skb->data_len += length;
1316 skb->truesize += PAGE_SIZE;
1319 /* strip the ethernet crc, problem is we're using pages now so
1320 * this whole operation can get a little cpu intensive
1322 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) {
1323 if (!(netdev->features & NETIF_F_RXFCS))
1324 pskb_trim(skb, skb->len - 4);
1328 total_rx_bytes += skb->len;
1331 e1000_rx_checksum(adapter, staterr, skb);
1333 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb);
1335 if (rx_desc->wb.upper.header_status &
1336 cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP))
1337 adapter->rx_hdr_split++;
1339 e1000_receive_skb(adapter, netdev, skb,
1340 staterr, rx_desc->wb.middle.vlan);
1343 rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
1344 buffer_info->skb = NULL;
1346 /* return some buffers to hardware, one at a time is too slow */
1347 if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
1348 adapter->alloc_rx_buf(rx_ring, cleaned_count,
1353 /* use prefetched values */
1355 buffer_info = next_buffer;
1357 staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
1359 rx_ring->next_to_clean = i;
1361 cleaned_count = e1000_desc_unused(rx_ring);
1363 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC);
1365 adapter->total_rx_bytes += total_rx_bytes;
1366 adapter->total_rx_packets += total_rx_packets;
1371 * e1000_consume_page - helper function
1373 static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb,
1378 skb->data_len += length;
1379 skb->truesize += PAGE_SIZE;
1383 * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy
1384 * @adapter: board private structure
1386 * the return value indicates whether actual cleaning was done, there
1387 * is no guarantee that everything was cleaned
1389 static bool e1000_clean_jumbo_rx_irq(struct e1000_ring *rx_ring, int *work_done,
1392 struct e1000_adapter *adapter = rx_ring->adapter;
1393 struct net_device *netdev = adapter->netdev;
1394 struct pci_dev *pdev = adapter->pdev;
1395 union e1000_rx_desc_extended *rx_desc, *next_rxd;
1396 struct e1000_buffer *buffer_info, *next_buffer;
1397 u32 length, staterr;
1399 int cleaned_count = 0;
1400 bool cleaned = false;
1401 unsigned int total_rx_bytes=0, total_rx_packets=0;
1403 i = rx_ring->next_to_clean;
1404 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
1405 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
1406 buffer_info = &rx_ring->buffer_info[i];
1408 while (staterr & E1000_RXD_STAT_DD) {
1409 struct sk_buff *skb;
1411 if (*work_done >= work_to_do)
1414 rmb(); /* read descriptor and rx_buffer_info after status DD */
1416 skb = buffer_info->skb;
1417 buffer_info->skb = NULL;
1420 if (i == rx_ring->count)
1422 next_rxd = E1000_RX_DESC_EXT(*rx_ring, i);
1425 next_buffer = &rx_ring->buffer_info[i];
1429 dma_unmap_page(&pdev->dev, buffer_info->dma, PAGE_SIZE,
1431 buffer_info->dma = 0;
1433 length = le16_to_cpu(rx_desc->wb.upper.length);
1435 /* errors is only valid for DD + EOP descriptors */
1436 if (unlikely((staterr & E1000_RXD_STAT_EOP) &&
1437 ((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) &&
1438 !(netdev->features & NETIF_F_RXALL)))) {
1439 /* recycle both page and skb */
1440 buffer_info->skb = skb;
1441 /* an error means any chain goes out the window too */
1442 if (rx_ring->rx_skb_top)
1443 dev_kfree_skb_irq(rx_ring->rx_skb_top);
1444 rx_ring->rx_skb_top = NULL;
1448 #define rxtop (rx_ring->rx_skb_top)
1449 if (!(staterr & E1000_RXD_STAT_EOP)) {
1450 /* this descriptor is only the beginning (or middle) */
1452 /* this is the beginning of a chain */
1454 skb_fill_page_desc(rxtop, 0, buffer_info->page,
1457 /* this is the middle of a chain */
1458 skb_fill_page_desc(rxtop,
1459 skb_shinfo(rxtop)->nr_frags,
1460 buffer_info->page, 0, length);
1461 /* re-use the skb, only consumed the page */
1462 buffer_info->skb = skb;
1464 e1000_consume_page(buffer_info, rxtop, length);
1468 /* end of the chain */
1469 skb_fill_page_desc(rxtop,
1470 skb_shinfo(rxtop)->nr_frags,
1471 buffer_info->page, 0, length);
1472 /* re-use the current skb, we only consumed the
1474 buffer_info->skb = skb;
1477 e1000_consume_page(buffer_info, skb, length);
1479 /* no chain, got EOP, this buf is the packet
1480 * copybreak to save the put_page/alloc_page */
1481 if (length <= copybreak &&
1482 skb_tailroom(skb) >= length) {
1484 vaddr = kmap_atomic(buffer_info->page);
1485 memcpy(skb_tail_pointer(skb), vaddr,
1487 kunmap_atomic(vaddr);
1488 /* re-use the page, so don't erase
1489 * buffer_info->page */
1490 skb_put(skb, length);
1492 skb_fill_page_desc(skb, 0,
1493 buffer_info->page, 0,
1495 e1000_consume_page(buffer_info, skb,
1501 /* Receive Checksum Offload */
1502 e1000_rx_checksum(adapter, staterr, skb);
1504 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb);
1506 /* probably a little skewed due to removing CRC */
1507 total_rx_bytes += skb->len;
1510 /* eth type trans needs skb->data to point to something */
1511 if (!pskb_may_pull(skb, ETH_HLEN)) {
1512 e_err("pskb_may_pull failed.\n");
1513 dev_kfree_skb_irq(skb);
1517 e1000_receive_skb(adapter, netdev, skb, staterr,
1518 rx_desc->wb.upper.vlan);
1521 rx_desc->wb.upper.status_error &= cpu_to_le32(~0xFF);
1523 /* return some buffers to hardware, one at a time is too slow */
1524 if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
1525 adapter->alloc_rx_buf(rx_ring, cleaned_count,
1530 /* use prefetched values */
1532 buffer_info = next_buffer;
1534 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
1536 rx_ring->next_to_clean = i;
1538 cleaned_count = e1000_desc_unused(rx_ring);
1540 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC);
1542 adapter->total_rx_bytes += total_rx_bytes;
1543 adapter->total_rx_packets += total_rx_packets;
1548 * e1000_clean_rx_ring - Free Rx Buffers per Queue
1549 * @rx_ring: Rx descriptor ring
1551 static void e1000_clean_rx_ring(struct e1000_ring *rx_ring)
1553 struct e1000_adapter *adapter = rx_ring->adapter;
1554 struct e1000_buffer *buffer_info;
1555 struct e1000_ps_page *ps_page;
1556 struct pci_dev *pdev = adapter->pdev;
1559 /* Free all the Rx ring sk_buffs */
1560 for (i = 0; i < rx_ring->count; i++) {
1561 buffer_info = &rx_ring->buffer_info[i];
1562 if (buffer_info->dma) {
1563 if (adapter->clean_rx == e1000_clean_rx_irq)
1564 dma_unmap_single(&pdev->dev, buffer_info->dma,
1565 adapter->rx_buffer_len,
1567 else if (adapter->clean_rx == e1000_clean_jumbo_rx_irq)
1568 dma_unmap_page(&pdev->dev, buffer_info->dma,
1571 else if (adapter->clean_rx == e1000_clean_rx_irq_ps)
1572 dma_unmap_single(&pdev->dev, buffer_info->dma,
1573 adapter->rx_ps_bsize0,
1575 buffer_info->dma = 0;
1578 if (buffer_info->page) {
1579 put_page(buffer_info->page);
1580 buffer_info->page = NULL;
1583 if (buffer_info->skb) {
1584 dev_kfree_skb(buffer_info->skb);
1585 buffer_info->skb = NULL;
1588 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
1589 ps_page = &buffer_info->ps_pages[j];
1592 dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE,
1595 put_page(ps_page->page);
1596 ps_page->page = NULL;
1600 /* there also may be some cached data from a chained receive */
1601 if (rx_ring->rx_skb_top) {
1602 dev_kfree_skb(rx_ring->rx_skb_top);
1603 rx_ring->rx_skb_top = NULL;
1606 /* Zero out the descriptor ring */
1607 memset(rx_ring->desc, 0, rx_ring->size);
1609 rx_ring->next_to_clean = 0;
1610 rx_ring->next_to_use = 0;
1611 adapter->flags2 &= ~FLAG2_IS_DISCARDING;
1613 writel(0, rx_ring->head);
1614 if (rx_ring->adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
1615 e1000e_update_rdt_wa(rx_ring, 0);
1617 writel(0, rx_ring->tail);
1620 static void e1000e_downshift_workaround(struct work_struct *work)
1622 struct e1000_adapter *adapter = container_of(work,
1623 struct e1000_adapter, downshift_task);
1625 if (test_bit(__E1000_DOWN, &adapter->state))
1628 e1000e_gig_downshift_workaround_ich8lan(&adapter->hw);
1632 * e1000_intr_msi - Interrupt Handler
1633 * @irq: interrupt number
1634 * @data: pointer to a network interface device structure
1636 static irqreturn_t e1000_intr_msi(int irq, void *data)
1638 struct net_device *netdev = data;
1639 struct e1000_adapter *adapter = netdev_priv(netdev);
1640 struct e1000_hw *hw = &adapter->hw;
1641 u32 icr = er32(ICR);
1644 * read ICR disables interrupts using IAM
1647 if (icr & E1000_ICR_LSC) {
1648 hw->mac.get_link_status = true;
1650 * ICH8 workaround-- Call gig speed drop workaround on cable
1651 * disconnect (LSC) before accessing any PHY registers
1653 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
1654 (!(er32(STATUS) & E1000_STATUS_LU)))
1655 schedule_work(&adapter->downshift_task);
1658 * 80003ES2LAN workaround-- For packet buffer work-around on
1659 * link down event; disable receives here in the ISR and reset
1660 * adapter in watchdog
1662 if (netif_carrier_ok(netdev) &&
1663 adapter->flags & FLAG_RX_NEEDS_RESTART) {
1664 /* disable receives */
1665 u32 rctl = er32(RCTL);
1666 ew32(RCTL, rctl & ~E1000_RCTL_EN);
1667 adapter->flags |= FLAG_RX_RESTART_NOW;
1669 /* guard against interrupt when we're going down */
1670 if (!test_bit(__E1000_DOWN, &adapter->state))
1671 mod_timer(&adapter->watchdog_timer, jiffies + 1);
1674 if (napi_schedule_prep(&adapter->napi)) {
1675 adapter->total_tx_bytes = 0;
1676 adapter->total_tx_packets = 0;
1677 adapter->total_rx_bytes = 0;
1678 adapter->total_rx_packets = 0;
1679 __napi_schedule(&adapter->napi);
1686 * e1000_intr - Interrupt Handler
1687 * @irq: interrupt number
1688 * @data: pointer to a network interface device structure
1690 static irqreturn_t e1000_intr(int irq, void *data)
1692 struct net_device *netdev = data;
1693 struct e1000_adapter *adapter = netdev_priv(netdev);
1694 struct e1000_hw *hw = &adapter->hw;
1695 u32 rctl, icr = er32(ICR);
1697 if (!icr || test_bit(__E1000_DOWN, &adapter->state))
1698 return IRQ_NONE; /* Not our interrupt */
1701 * IMS will not auto-mask if INT_ASSERTED is not set, and if it is
1702 * not set, then the adapter didn't send an interrupt
1704 if (!(icr & E1000_ICR_INT_ASSERTED))
1708 * Interrupt Auto-Mask...upon reading ICR,
1709 * interrupts are masked. No need for the
1713 if (icr & E1000_ICR_LSC) {
1714 hw->mac.get_link_status = true;
1716 * ICH8 workaround-- Call gig speed drop workaround on cable
1717 * disconnect (LSC) before accessing any PHY registers
1719 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
1720 (!(er32(STATUS) & E1000_STATUS_LU)))
1721 schedule_work(&adapter->downshift_task);
1724 * 80003ES2LAN workaround--
1725 * For packet buffer work-around on link down event;
1726 * disable receives here in the ISR and
1727 * reset adapter in watchdog
1729 if (netif_carrier_ok(netdev) &&
1730 (adapter->flags & FLAG_RX_NEEDS_RESTART)) {
1731 /* disable receives */
1733 ew32(RCTL, rctl & ~E1000_RCTL_EN);
1734 adapter->flags |= FLAG_RX_RESTART_NOW;
1736 /* guard against interrupt when we're going down */
1737 if (!test_bit(__E1000_DOWN, &adapter->state))
1738 mod_timer(&adapter->watchdog_timer, jiffies + 1);
1741 if (napi_schedule_prep(&adapter->napi)) {
1742 adapter->total_tx_bytes = 0;
1743 adapter->total_tx_packets = 0;
1744 adapter->total_rx_bytes = 0;
1745 adapter->total_rx_packets = 0;
1746 __napi_schedule(&adapter->napi);
1752 static irqreturn_t e1000_msix_other(int irq, void *data)
1754 struct net_device *netdev = data;
1755 struct e1000_adapter *adapter = netdev_priv(netdev);
1756 struct e1000_hw *hw = &adapter->hw;
1757 u32 icr = er32(ICR);
1759 if (!(icr & E1000_ICR_INT_ASSERTED)) {
1760 if (!test_bit(__E1000_DOWN, &adapter->state))
1761 ew32(IMS, E1000_IMS_OTHER);
1765 if (icr & adapter->eiac_mask)
1766 ew32(ICS, (icr & adapter->eiac_mask));
1768 if (icr & E1000_ICR_OTHER) {
1769 if (!(icr & E1000_ICR_LSC))
1770 goto no_link_interrupt;
1771 hw->mac.get_link_status = true;
1772 /* guard against interrupt when we're going down */
1773 if (!test_bit(__E1000_DOWN, &adapter->state))
1774 mod_timer(&adapter->watchdog_timer, jiffies + 1);
1778 if (!test_bit(__E1000_DOWN, &adapter->state))
1779 ew32(IMS, E1000_IMS_LSC | E1000_IMS_OTHER);
1785 static irqreturn_t e1000_intr_msix_tx(int irq, void *data)
1787 struct net_device *netdev = data;
1788 struct e1000_adapter *adapter = netdev_priv(netdev);
1789 struct e1000_hw *hw = &adapter->hw;
1790 struct e1000_ring *tx_ring = adapter->tx_ring;
1793 adapter->total_tx_bytes = 0;
1794 adapter->total_tx_packets = 0;
1796 if (!e1000_clean_tx_irq(tx_ring))
1797 /* Ring was not completely cleaned, so fire another interrupt */
1798 ew32(ICS, tx_ring->ims_val);
1803 static irqreturn_t e1000_intr_msix_rx(int irq, void *data)
1805 struct net_device *netdev = data;
1806 struct e1000_adapter *adapter = netdev_priv(netdev);
1807 struct e1000_ring *rx_ring = adapter->rx_ring;
1809 /* Write the ITR value calculated at the end of the
1810 * previous interrupt.
1812 if (rx_ring->set_itr) {
1813 writel(1000000000 / (rx_ring->itr_val * 256),
1814 rx_ring->itr_register);
1815 rx_ring->set_itr = 0;
1818 if (napi_schedule_prep(&adapter->napi)) {
1819 adapter->total_rx_bytes = 0;
1820 adapter->total_rx_packets = 0;
1821 __napi_schedule(&adapter->napi);
1827 * e1000_configure_msix - Configure MSI-X hardware
1829 * e1000_configure_msix sets up the hardware to properly
1830 * generate MSI-X interrupts.
1832 static void e1000_configure_msix(struct e1000_adapter *adapter)
1834 struct e1000_hw *hw = &adapter->hw;
1835 struct e1000_ring *rx_ring = adapter->rx_ring;
1836 struct e1000_ring *tx_ring = adapter->tx_ring;
1838 u32 ctrl_ext, ivar = 0;
1840 adapter->eiac_mask = 0;
1842 /* Workaround issue with spurious interrupts on 82574 in MSI-X mode */
1843 if (hw->mac.type == e1000_82574) {
1844 u32 rfctl = er32(RFCTL);
1845 rfctl |= E1000_RFCTL_ACK_DIS;
1849 #define E1000_IVAR_INT_ALLOC_VALID 0x8
1850 /* Configure Rx vector */
1851 rx_ring->ims_val = E1000_IMS_RXQ0;
1852 adapter->eiac_mask |= rx_ring->ims_val;
1853 if (rx_ring->itr_val)
1854 writel(1000000000 / (rx_ring->itr_val * 256),
1855 rx_ring->itr_register);
1857 writel(1, rx_ring->itr_register);
1858 ivar = E1000_IVAR_INT_ALLOC_VALID | vector;
1860 /* Configure Tx vector */
1861 tx_ring->ims_val = E1000_IMS_TXQ0;
1863 if (tx_ring->itr_val)
1864 writel(1000000000 / (tx_ring->itr_val * 256),
1865 tx_ring->itr_register);
1867 writel(1, tx_ring->itr_register);
1868 adapter->eiac_mask |= tx_ring->ims_val;
1869 ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 8);
1871 /* set vector for Other Causes, e.g. link changes */
1873 ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 16);
1874 if (rx_ring->itr_val)
1875 writel(1000000000 / (rx_ring->itr_val * 256),
1876 hw->hw_addr + E1000_EITR_82574(vector));
1878 writel(1, hw->hw_addr + E1000_EITR_82574(vector));
1880 /* Cause Tx interrupts on every write back */
1885 /* enable MSI-X PBA support */
1886 ctrl_ext = er32(CTRL_EXT);
1887 ctrl_ext |= E1000_CTRL_EXT_PBA_CLR;
1889 /* Auto-Mask Other interrupts upon ICR read */
1890 #define E1000_EIAC_MASK_82574 0x01F00000
1891 ew32(IAM, ~E1000_EIAC_MASK_82574 | E1000_IMS_OTHER);
1892 ctrl_ext |= E1000_CTRL_EXT_EIAME;
1893 ew32(CTRL_EXT, ctrl_ext);
1897 void e1000e_reset_interrupt_capability(struct e1000_adapter *adapter)
1899 if (adapter->msix_entries) {
1900 pci_disable_msix(adapter->pdev);
1901 kfree(adapter->msix_entries);
1902 adapter->msix_entries = NULL;
1903 } else if (adapter->flags & FLAG_MSI_ENABLED) {
1904 pci_disable_msi(adapter->pdev);
1905 adapter->flags &= ~FLAG_MSI_ENABLED;
1910 * e1000e_set_interrupt_capability - set MSI or MSI-X if supported
1912 * Attempt to configure interrupts using the best available
1913 * capabilities of the hardware and kernel.
1915 void e1000e_set_interrupt_capability(struct e1000_adapter *adapter)
1920 switch (adapter->int_mode) {
1921 case E1000E_INT_MODE_MSIX:
1922 if (adapter->flags & FLAG_HAS_MSIX) {
1923 adapter->num_vectors = 3; /* RxQ0, TxQ0 and other */
1924 adapter->msix_entries = kcalloc(adapter->num_vectors,
1925 sizeof(struct msix_entry),
1927 if (adapter->msix_entries) {
1928 for (i = 0; i < adapter->num_vectors; i++)
1929 adapter->msix_entries[i].entry = i;
1931 err = pci_enable_msix(adapter->pdev,
1932 adapter->msix_entries,
1933 adapter->num_vectors);
1937 /* MSI-X failed, so fall through and try MSI */
1938 e_err("Failed to initialize MSI-X interrupts. Falling back to MSI interrupts.\n");
1939 e1000e_reset_interrupt_capability(adapter);
1941 adapter->int_mode = E1000E_INT_MODE_MSI;
1943 case E1000E_INT_MODE_MSI:
1944 if (!pci_enable_msi(adapter->pdev)) {
1945 adapter->flags |= FLAG_MSI_ENABLED;
1947 adapter->int_mode = E1000E_INT_MODE_LEGACY;
1948 e_err("Failed to initialize MSI interrupts. Falling back to legacy interrupts.\n");
1951 case E1000E_INT_MODE_LEGACY:
1952 /* Don't do anything; this is the system default */
1956 /* store the number of vectors being used */
1957 adapter->num_vectors = 1;
1961 * e1000_request_msix - Initialize MSI-X interrupts
1963 * e1000_request_msix allocates MSI-X vectors and requests interrupts from the
1966 static int e1000_request_msix(struct e1000_adapter *adapter)
1968 struct net_device *netdev = adapter->netdev;
1969 int err = 0, vector = 0;
1971 if (strlen(netdev->name) < (IFNAMSIZ - 5))
1972 snprintf(adapter->rx_ring->name,
1973 sizeof(adapter->rx_ring->name) - 1,
1974 "%s-rx-0", netdev->name);
1976 memcpy(adapter->rx_ring->name, netdev->name, IFNAMSIZ);
1977 err = request_irq(adapter->msix_entries[vector].vector,
1978 e1000_intr_msix_rx, 0, adapter->rx_ring->name,
1982 adapter->rx_ring->itr_register = adapter->hw.hw_addr +
1983 E1000_EITR_82574(vector);
1984 adapter->rx_ring->itr_val = adapter->itr;
1987 if (strlen(netdev->name) < (IFNAMSIZ - 5))
1988 snprintf(adapter->tx_ring->name,
1989 sizeof(adapter->tx_ring->name) - 1,
1990 "%s-tx-0", netdev->name);
1992 memcpy(adapter->tx_ring->name, netdev->name, IFNAMSIZ);
1993 err = request_irq(adapter->msix_entries[vector].vector,
1994 e1000_intr_msix_tx, 0, adapter->tx_ring->name,
1998 adapter->tx_ring->itr_register = adapter->hw.hw_addr +
1999 E1000_EITR_82574(vector);
2000 adapter->tx_ring->itr_val = adapter->itr;
2003 err = request_irq(adapter->msix_entries[vector].vector,
2004 e1000_msix_other, 0, netdev->name, netdev);
2008 e1000_configure_msix(adapter);
2014 * e1000_request_irq - initialize interrupts
2016 * Attempts to configure interrupts using the best available
2017 * capabilities of the hardware and kernel.
2019 static int e1000_request_irq(struct e1000_adapter *adapter)
2021 struct net_device *netdev = adapter->netdev;
2024 if (adapter->msix_entries) {
2025 err = e1000_request_msix(adapter);
2028 /* fall back to MSI */
2029 e1000e_reset_interrupt_capability(adapter);
2030 adapter->int_mode = E1000E_INT_MODE_MSI;
2031 e1000e_set_interrupt_capability(adapter);
2033 if (adapter->flags & FLAG_MSI_ENABLED) {
2034 err = request_irq(adapter->pdev->irq, e1000_intr_msi, 0,
2035 netdev->name, netdev);
2039 /* fall back to legacy interrupt */
2040 e1000e_reset_interrupt_capability(adapter);
2041 adapter->int_mode = E1000E_INT_MODE_LEGACY;
2044 err = request_irq(adapter->pdev->irq, e1000_intr, IRQF_SHARED,
2045 netdev->name, netdev);
2047 e_err("Unable to allocate interrupt, Error: %d\n", err);
2052 static void e1000_free_irq(struct e1000_adapter *adapter)
2054 struct net_device *netdev = adapter->netdev;
2056 if (adapter->msix_entries) {
2059 free_irq(adapter->msix_entries[vector].vector, netdev);
2062 free_irq(adapter->msix_entries[vector].vector, netdev);
2065 /* Other Causes interrupt vector */
2066 free_irq(adapter->msix_entries[vector].vector, netdev);
2070 free_irq(adapter->pdev->irq, netdev);
2074 * e1000_irq_disable - Mask off interrupt generation on the NIC
2076 static void e1000_irq_disable(struct e1000_adapter *adapter)
2078 struct e1000_hw *hw = &adapter->hw;
2081 if (adapter->msix_entries)
2082 ew32(EIAC_82574, 0);
2085 if (adapter->msix_entries) {
2087 for (i = 0; i < adapter->num_vectors; i++)
2088 synchronize_irq(adapter->msix_entries[i].vector);
2090 synchronize_irq(adapter->pdev->irq);
2095 * e1000_irq_enable - Enable default interrupt generation settings
2097 static void e1000_irq_enable(struct e1000_adapter *adapter)
2099 struct e1000_hw *hw = &adapter->hw;
2101 if (adapter->msix_entries) {
2102 ew32(EIAC_82574, adapter->eiac_mask & E1000_EIAC_MASK_82574);
2103 ew32(IMS, adapter->eiac_mask | E1000_IMS_OTHER | E1000_IMS_LSC);
2105 ew32(IMS, IMS_ENABLE_MASK);
2111 * e1000e_get_hw_control - get control of the h/w from f/w
2112 * @adapter: address of board private structure
2114 * e1000e_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit.
2115 * For ASF and Pass Through versions of f/w this means that
2116 * the driver is loaded. For AMT version (only with 82573)
2117 * of the f/w this means that the network i/f is open.
2119 void e1000e_get_hw_control(struct e1000_adapter *adapter)
2121 struct e1000_hw *hw = &adapter->hw;
2125 /* Let firmware know the driver has taken over */
2126 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
2128 ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD);
2129 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
2130 ctrl_ext = er32(CTRL_EXT);
2131 ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
2136 * e1000e_release_hw_control - release control of the h/w to f/w
2137 * @adapter: address of board private structure
2139 * e1000e_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit.
2140 * For ASF and Pass Through versions of f/w this means that the
2141 * driver is no longer loaded. For AMT version (only with 82573) i
2142 * of the f/w this means that the network i/f is closed.
2145 void e1000e_release_hw_control(struct e1000_adapter *adapter)
2147 struct e1000_hw *hw = &adapter->hw;
2151 /* Let firmware taken over control of h/w */
2152 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
2154 ew32(SWSM, swsm & ~E1000_SWSM_DRV_LOAD);
2155 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
2156 ctrl_ext = er32(CTRL_EXT);
2157 ew32(CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD);
2162 * e1000_alloc_ring_dma - allocate memory for a ring structure
2164 static int e1000_alloc_ring_dma(struct e1000_adapter *adapter,
2165 struct e1000_ring *ring)
2167 struct pci_dev *pdev = adapter->pdev;
2169 ring->desc = dma_alloc_coherent(&pdev->dev, ring->size, &ring->dma,
2178 * e1000e_setup_tx_resources - allocate Tx resources (Descriptors)
2179 * @tx_ring: Tx descriptor ring
2181 * Return 0 on success, negative on failure
2183 int e1000e_setup_tx_resources(struct e1000_ring *tx_ring)
2185 struct e1000_adapter *adapter = tx_ring->adapter;
2186 int err = -ENOMEM, size;
2188 size = sizeof(struct e1000_buffer) * tx_ring->count;
2189 tx_ring->buffer_info = vzalloc(size);
2190 if (!tx_ring->buffer_info)
2193 /* round up to nearest 4K */
2194 tx_ring->size = tx_ring->count * sizeof(struct e1000_tx_desc);
2195 tx_ring->size = ALIGN(tx_ring->size, 4096);
2197 err = e1000_alloc_ring_dma(adapter, tx_ring);
2201 tx_ring->next_to_use = 0;
2202 tx_ring->next_to_clean = 0;
2206 vfree(tx_ring->buffer_info);
2207 e_err("Unable to allocate memory for the transmit descriptor ring\n");
2212 * e1000e_setup_rx_resources - allocate Rx resources (Descriptors)
2213 * @rx_ring: Rx descriptor ring
2215 * Returns 0 on success, negative on failure
2217 int e1000e_setup_rx_resources(struct e1000_ring *rx_ring)
2219 struct e1000_adapter *adapter = rx_ring->adapter;
2220 struct e1000_buffer *buffer_info;
2221 int i, size, desc_len, err = -ENOMEM;
2223 size = sizeof(struct e1000_buffer) * rx_ring->count;
2224 rx_ring->buffer_info = vzalloc(size);
2225 if (!rx_ring->buffer_info)
2228 for (i = 0; i < rx_ring->count; i++) {
2229 buffer_info = &rx_ring->buffer_info[i];
2230 buffer_info->ps_pages = kcalloc(PS_PAGE_BUFFERS,
2231 sizeof(struct e1000_ps_page),
2233 if (!buffer_info->ps_pages)
2237 desc_len = sizeof(union e1000_rx_desc_packet_split);
2239 /* Round up to nearest 4K */
2240 rx_ring->size = rx_ring->count * desc_len;
2241 rx_ring->size = ALIGN(rx_ring->size, 4096);
2243 err = e1000_alloc_ring_dma(adapter, rx_ring);
2247 rx_ring->next_to_clean = 0;
2248 rx_ring->next_to_use = 0;
2249 rx_ring->rx_skb_top = NULL;
2254 for (i = 0; i < rx_ring->count; i++) {
2255 buffer_info = &rx_ring->buffer_info[i];
2256 kfree(buffer_info->ps_pages);
2259 vfree(rx_ring->buffer_info);
2260 e_err("Unable to allocate memory for the receive descriptor ring\n");
2265 * e1000_clean_tx_ring - Free Tx Buffers
2266 * @tx_ring: Tx descriptor ring
2268 static void e1000_clean_tx_ring(struct e1000_ring *tx_ring)
2270 struct e1000_adapter *adapter = tx_ring->adapter;
2271 struct e1000_buffer *buffer_info;
2275 for (i = 0; i < tx_ring->count; i++) {
2276 buffer_info = &tx_ring->buffer_info[i];
2277 e1000_put_txbuf(tx_ring, buffer_info);
2280 netdev_reset_queue(adapter->netdev);
2281 size = sizeof(struct e1000_buffer) * tx_ring->count;
2282 memset(tx_ring->buffer_info, 0, size);
2284 memset(tx_ring->desc, 0, tx_ring->size);
2286 tx_ring->next_to_use = 0;
2287 tx_ring->next_to_clean = 0;
2289 writel(0, tx_ring->head);
2290 if (tx_ring->adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
2291 e1000e_update_tdt_wa(tx_ring, 0);
2293 writel(0, tx_ring->tail);
2297 * e1000e_free_tx_resources - Free Tx Resources per Queue
2298 * @tx_ring: Tx descriptor ring
2300 * Free all transmit software resources
2302 void e1000e_free_tx_resources(struct e1000_ring *tx_ring)
2304 struct e1000_adapter *adapter = tx_ring->adapter;
2305 struct pci_dev *pdev = adapter->pdev;
2307 e1000_clean_tx_ring(tx_ring);
2309 vfree(tx_ring->buffer_info);
2310 tx_ring->buffer_info = NULL;
2312 dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc,
2314 tx_ring->desc = NULL;
2318 * e1000e_free_rx_resources - Free Rx Resources
2319 * @rx_ring: Rx descriptor ring
2321 * Free all receive software resources
2323 void e1000e_free_rx_resources(struct e1000_ring *rx_ring)
2325 struct e1000_adapter *adapter = rx_ring->adapter;
2326 struct pci_dev *pdev = adapter->pdev;
2329 e1000_clean_rx_ring(rx_ring);
2331 for (i = 0; i < rx_ring->count; i++)
2332 kfree(rx_ring->buffer_info[i].ps_pages);
2334 vfree(rx_ring->buffer_info);
2335 rx_ring->buffer_info = NULL;
2337 dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc,
2339 rx_ring->desc = NULL;
2343 * e1000_update_itr - update the dynamic ITR value based on statistics
2344 * @adapter: pointer to adapter
2345 * @itr_setting: current adapter->itr
2346 * @packets: the number of packets during this measurement interval
2347 * @bytes: the number of bytes during this measurement interval
2349 * Stores a new ITR value based on packets and byte
2350 * counts during the last interrupt. The advantage of per interrupt
2351 * computation is faster updates and more accurate ITR for the current
2352 * traffic pattern. Constants in this function were computed
2353 * based on theoretical maximum wire speed and thresholds were set based
2354 * on testing data as well as attempting to minimize response time
2355 * while increasing bulk throughput. This functionality is controlled
2356 * by the InterruptThrottleRate module parameter.
2358 static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
2359 u16 itr_setting, int packets,
2362 unsigned int retval = itr_setting;
2367 switch (itr_setting) {
2368 case lowest_latency:
2369 /* handle TSO and jumbo frames */
2370 if (bytes/packets > 8000)
2371 retval = bulk_latency;
2372 else if ((packets < 5) && (bytes > 512))
2373 retval = low_latency;
2375 case low_latency: /* 50 usec aka 20000 ints/s */
2376 if (bytes > 10000) {
2377 /* this if handles the TSO accounting */
2378 if (bytes/packets > 8000)
2379 retval = bulk_latency;
2380 else if ((packets < 10) || ((bytes/packets) > 1200))
2381 retval = bulk_latency;
2382 else if ((packets > 35))
2383 retval = lowest_latency;
2384 } else if (bytes/packets > 2000) {
2385 retval = bulk_latency;
2386 } else if (packets <= 2 && bytes < 512) {
2387 retval = lowest_latency;
2390 case bulk_latency: /* 250 usec aka 4000 ints/s */
2391 if (bytes > 25000) {
2393 retval = low_latency;
2394 } else if (bytes < 6000) {
2395 retval = low_latency;
2403 static void e1000_set_itr(struct e1000_adapter *adapter)
2405 struct e1000_hw *hw = &adapter->hw;
2407 u32 new_itr = adapter->itr;
2409 /* for non-gigabit speeds, just fix the interrupt rate at 4000 */
2410 if (adapter->link_speed != SPEED_1000) {
2416 if (adapter->flags2 & FLAG2_DISABLE_AIM) {
2421 adapter->tx_itr = e1000_update_itr(adapter,
2423 adapter->total_tx_packets,
2424 adapter->total_tx_bytes);
2425 /* conservative mode (itr 3) eliminates the lowest_latency setting */
2426 if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
2427 adapter->tx_itr = low_latency;
2429 adapter->rx_itr = e1000_update_itr(adapter,
2431 adapter->total_rx_packets,
2432 adapter->total_rx_bytes);
2433 /* conservative mode (itr 3) eliminates the lowest_latency setting */
2434 if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
2435 adapter->rx_itr = low_latency;
2437 current_itr = max(adapter->rx_itr, adapter->tx_itr);
2439 switch (current_itr) {
2440 /* counts and packets in update_itr are dependent on these numbers */
2441 case lowest_latency:
2445 new_itr = 20000; /* aka hwitr = ~200 */
2455 if (new_itr != adapter->itr) {
2457 * this attempts to bias the interrupt rate towards Bulk
2458 * by adding intermediate steps when interrupt rate is
2461 new_itr = new_itr > adapter->itr ?
2462 min(adapter->itr + (new_itr >> 2), new_itr) :
2464 adapter->itr = new_itr;
2465 adapter->rx_ring->itr_val = new_itr;
2466 if (adapter->msix_entries)
2467 adapter->rx_ring->set_itr = 1;
2470 ew32(ITR, 1000000000 / (new_itr * 256));
2477 * e1000e_write_itr - write the ITR value to the appropriate registers
2478 * @adapter: address of board private structure
2479 * @itr: new ITR value to program
2481 * e1000e_write_itr determines if the adapter is in MSI-X mode
2482 * and, if so, writes the EITR registers with the ITR value.
2483 * Otherwise, it writes the ITR value into the ITR register.
2485 void e1000e_write_itr(struct e1000_adapter *adapter, u32 itr)
2487 struct e1000_hw *hw = &adapter->hw;
2488 u32 new_itr = itr ? 1000000000 / (itr * 256) : 0;
2490 if (adapter->msix_entries) {
2493 for (vector = 0; vector < adapter->num_vectors; vector++)
2494 writel(new_itr, hw->hw_addr + E1000_EITR_82574(vector));
2501 * e1000_alloc_queues - Allocate memory for all rings
2502 * @adapter: board private structure to initialize
2504 static int __devinit e1000_alloc_queues(struct e1000_adapter *adapter)
2506 int size = sizeof(struct e1000_ring);
2508 adapter->tx_ring = kzalloc(size, GFP_KERNEL);
2509 if (!adapter->tx_ring)
2511 adapter->tx_ring->count = adapter->tx_ring_count;
2512 adapter->tx_ring->adapter = adapter;
2514 adapter->rx_ring = kzalloc(size, GFP_KERNEL);
2515 if (!adapter->rx_ring)
2517 adapter->rx_ring->count = adapter->rx_ring_count;
2518 adapter->rx_ring->adapter = adapter;
2522 e_err("Unable to allocate memory for queues\n");
2523 kfree(adapter->rx_ring);
2524 kfree(adapter->tx_ring);
2529 * e1000e_poll - NAPI Rx polling callback
2530 * @napi: struct associated with this polling callback
2531 * @weight: number of packets driver is allowed to process this poll
2533 static int e1000e_poll(struct napi_struct *napi, int weight)
2535 struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter,
2537 struct e1000_hw *hw = &adapter->hw;
2538 struct net_device *poll_dev = adapter->netdev;
2539 int tx_cleaned = 1, work_done = 0;
2541 adapter = netdev_priv(poll_dev);
2543 if (!adapter->msix_entries ||
2544 (adapter->rx_ring->ims_val & adapter->tx_ring->ims_val))
2545 tx_cleaned = e1000_clean_tx_irq(adapter->tx_ring);
2547 adapter->clean_rx(adapter->rx_ring, &work_done, weight);
2552 /* If weight not fully consumed, exit the polling mode */
2553 if (work_done < weight) {
2554 if (adapter->itr_setting & 3)
2555 e1000_set_itr(adapter);
2556 napi_complete(napi);
2557 if (!test_bit(__E1000_DOWN, &adapter->state)) {
2558 if (adapter->msix_entries)
2559 ew32(IMS, adapter->rx_ring->ims_val);
2561 e1000_irq_enable(adapter);
2568 static int e1000_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
2570 struct e1000_adapter *adapter = netdev_priv(netdev);
2571 struct e1000_hw *hw = &adapter->hw;
2574 /* don't update vlan cookie if already programmed */
2575 if ((adapter->hw.mng_cookie.status &
2576 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
2577 (vid == adapter->mng_vlan_id))
2580 /* add VID to filter table */
2581 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
2582 index = (vid >> 5) & 0x7F;
2583 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
2584 vfta |= (1 << (vid & 0x1F));
2585 hw->mac.ops.write_vfta(hw, index, vfta);
2588 set_bit(vid, adapter->active_vlans);
2593 static int e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
2595 struct e1000_adapter *adapter = netdev_priv(netdev);
2596 struct e1000_hw *hw = &adapter->hw;
2599 if ((adapter->hw.mng_cookie.status &
2600 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
2601 (vid == adapter->mng_vlan_id)) {
2602 /* release control to f/w */
2603 e1000e_release_hw_control(adapter);
2607 /* remove VID from filter table */
2608 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
2609 index = (vid >> 5) & 0x7F;
2610 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
2611 vfta &= ~(1 << (vid & 0x1F));
2612 hw->mac.ops.write_vfta(hw, index, vfta);
2615 clear_bit(vid, adapter->active_vlans);
2621 * e1000e_vlan_filter_disable - helper to disable hw VLAN filtering
2622 * @adapter: board private structure to initialize
2624 static void e1000e_vlan_filter_disable(struct e1000_adapter *adapter)
2626 struct net_device *netdev = adapter->netdev;
2627 struct e1000_hw *hw = &adapter->hw;
2630 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
2631 /* disable VLAN receive filtering */
2633 rctl &= ~(E1000_RCTL_VFE | E1000_RCTL_CFIEN);
2636 if (adapter->mng_vlan_id != (u16)E1000_MNG_VLAN_NONE) {
2637 e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
2638 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
2644 * e1000e_vlan_filter_enable - helper to enable HW VLAN filtering
2645 * @adapter: board private structure to initialize
2647 static void e1000e_vlan_filter_enable(struct e1000_adapter *adapter)
2649 struct e1000_hw *hw = &adapter->hw;
2652 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
2653 /* enable VLAN receive filtering */
2655 rctl |= E1000_RCTL_VFE;
2656 rctl &= ~E1000_RCTL_CFIEN;
2662 * e1000e_vlan_strip_enable - helper to disable HW VLAN stripping
2663 * @adapter: board private structure to initialize
2665 static void e1000e_vlan_strip_disable(struct e1000_adapter *adapter)
2667 struct e1000_hw *hw = &adapter->hw;
2670 /* disable VLAN tag insert/strip */
2672 ctrl &= ~E1000_CTRL_VME;
2677 * e1000e_vlan_strip_enable - helper to enable HW VLAN stripping
2678 * @adapter: board private structure to initialize
2680 static void e1000e_vlan_strip_enable(struct e1000_adapter *adapter)
2682 struct e1000_hw *hw = &adapter->hw;
2685 /* enable VLAN tag insert/strip */
2687 ctrl |= E1000_CTRL_VME;
2691 static void e1000_update_mng_vlan(struct e1000_adapter *adapter)
2693 struct net_device *netdev = adapter->netdev;
2694 u16 vid = adapter->hw.mng_cookie.vlan_id;
2695 u16 old_vid = adapter->mng_vlan_id;
2697 if (adapter->hw.mng_cookie.status &
2698 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) {
2699 e1000_vlan_rx_add_vid(netdev, vid);
2700 adapter->mng_vlan_id = vid;
2703 if ((old_vid != (u16)E1000_MNG_VLAN_NONE) && (vid != old_vid))
2704 e1000_vlan_rx_kill_vid(netdev, old_vid);
2707 static void e1000_restore_vlan(struct e1000_adapter *adapter)
2711 e1000_vlan_rx_add_vid(adapter->netdev, 0);
2713 for_each_set_bit(vid, adapter->active_vlans, VLAN_N_VID)
2714 e1000_vlan_rx_add_vid(adapter->netdev, vid);
2717 static void e1000_init_manageability_pt(struct e1000_adapter *adapter)
2719 struct e1000_hw *hw = &adapter->hw;
2720 u32 manc, manc2h, mdef, i, j;
2722 if (!(adapter->flags & FLAG_MNG_PT_ENABLED))
2728 * enable receiving management packets to the host. this will probably
2729 * generate destination unreachable messages from the host OS, but
2730 * the packets will be handled on SMBUS
2732 manc |= E1000_MANC_EN_MNG2HOST;
2733 manc2h = er32(MANC2H);
2735 switch (hw->mac.type) {
2737 manc2h |= (E1000_MANC2H_PORT_623 | E1000_MANC2H_PORT_664);
2742 * Check if IPMI pass-through decision filter already exists;
2745 for (i = 0, j = 0; i < 8; i++) {
2746 mdef = er32(MDEF(i));
2748 /* Ignore filters with anything other than IPMI ports */
2749 if (mdef & ~(E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664))
2752 /* Enable this decision filter in MANC2H */
2759 if (j == (E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664))
2762 /* Create new decision filter in an empty filter */
2763 for (i = 0, j = 0; i < 8; i++)
2764 if (er32(MDEF(i)) == 0) {
2765 ew32(MDEF(i), (E1000_MDEF_PORT_623 |
2766 E1000_MDEF_PORT_664));
2773 e_warn("Unable to create IPMI pass-through filter\n");
2777 ew32(MANC2H, manc2h);
2782 * e1000_configure_tx - Configure Transmit Unit after Reset
2783 * @adapter: board private structure
2785 * Configure the Tx unit of the MAC after a reset.
2787 static void e1000_configure_tx(struct e1000_adapter *adapter)
2789 struct e1000_hw *hw = &adapter->hw;
2790 struct e1000_ring *tx_ring = adapter->tx_ring;
2794 /* Setup the HW Tx Head and Tail descriptor pointers */
2795 tdba = tx_ring->dma;
2796 tdlen = tx_ring->count * sizeof(struct e1000_tx_desc);
2797 ew32(TDBAL(0), (tdba & DMA_BIT_MASK(32)));
2798 ew32(TDBAH(0), (tdba >> 32));
2799 ew32(TDLEN(0), tdlen);
2802 tx_ring->head = adapter->hw.hw_addr + E1000_TDH(0);
2803 tx_ring->tail = adapter->hw.hw_addr + E1000_TDT(0);
2805 /* Set the Tx Interrupt Delay register */
2806 ew32(TIDV, adapter->tx_int_delay);
2807 /* Tx irq moderation */
2808 ew32(TADV, adapter->tx_abs_int_delay);
2810 if (adapter->flags2 & FLAG2_DMA_BURST) {
2811 u32 txdctl = er32(TXDCTL(0));
2812 txdctl &= ~(E1000_TXDCTL_PTHRESH | E1000_TXDCTL_HTHRESH |
2813 E1000_TXDCTL_WTHRESH);
2815 * set up some performance related parameters to encourage the
2816 * hardware to use the bus more efficiently in bursts, depends
2817 * on the tx_int_delay to be enabled,
2818 * wthresh = 5 ==> burst write a cacheline (64 bytes) at a time
2819 * hthresh = 1 ==> prefetch when one or more available
2820 * pthresh = 0x1f ==> prefetch if internal cache 31 or less
2821 * BEWARE: this seems to work but should be considered first if
2822 * there are Tx hangs or other Tx related bugs
2824 txdctl |= E1000_TXDCTL_DMA_BURST_ENABLE;
2825 ew32(TXDCTL(0), txdctl);
2827 /* erratum work around: set txdctl the same for both queues */
2828 ew32(TXDCTL(1), er32(TXDCTL(0)));
2830 if (adapter->flags & FLAG_TARC_SPEED_MODE_BIT) {
2831 tarc = er32(TARC(0));
2833 * set the speed mode bit, we'll clear it if we're not at
2834 * gigabit link later
2836 #define SPEED_MODE_BIT (1 << 21)
2837 tarc |= SPEED_MODE_BIT;
2838 ew32(TARC(0), tarc);
2841 /* errata: program both queues to unweighted RR */
2842 if (adapter->flags & FLAG_TARC_SET_BIT_ZERO) {
2843 tarc = er32(TARC(0));
2845 ew32(TARC(0), tarc);
2846 tarc = er32(TARC(1));
2848 ew32(TARC(1), tarc);
2851 /* Setup Transmit Descriptor Settings for eop descriptor */
2852 adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
2854 /* only set IDE if we are delaying interrupts using the timers */
2855 if (adapter->tx_int_delay)
2856 adapter->txd_cmd |= E1000_TXD_CMD_IDE;
2858 /* enable Report Status bit */
2859 adapter->txd_cmd |= E1000_TXD_CMD_RS;
2861 hw->mac.ops.config_collision_dist(hw);
2865 * e1000_setup_rctl - configure the receive control registers
2866 * @adapter: Board private structure
2868 #define PAGE_USE_COUNT(S) (((S) >> PAGE_SHIFT) + \
2869 (((S) & (PAGE_SIZE - 1)) ? 1 : 0))
2870 static void e1000_setup_rctl(struct e1000_adapter *adapter)
2872 struct e1000_hw *hw = &adapter->hw;
2876 /* Workaround Si errata on PCHx - configure jumbo frame flow */
2877 if (hw->mac.type >= e1000_pch2lan) {
2880 if (adapter->netdev->mtu > ETH_DATA_LEN)
2881 ret_val = e1000_lv_jumbo_workaround_ich8lan(hw, true);
2883 ret_val = e1000_lv_jumbo_workaround_ich8lan(hw, false);
2886 e_dbg("failed to enable jumbo frame workaround mode\n");
2889 /* Program MC offset vector base */
2891 rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
2892 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM |
2893 E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
2894 (adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT);
2896 /* Do not Store bad packets */
2897 rctl &= ~E1000_RCTL_SBP;
2899 /* Enable Long Packet receive */
2900 if (adapter->netdev->mtu <= ETH_DATA_LEN)
2901 rctl &= ~E1000_RCTL_LPE;
2903 rctl |= E1000_RCTL_LPE;
2905 /* Some systems expect that the CRC is included in SMBUS traffic. The
2906 * hardware strips the CRC before sending to both SMBUS (BMC) and to
2907 * host memory when this is enabled
2909 if (adapter->flags2 & FLAG2_CRC_STRIPPING)
2910 rctl |= E1000_RCTL_SECRC;
2912 /* Workaround Si errata on 82577 PHY - configure IPG for jumbos */
2913 if ((hw->phy.type == e1000_phy_82577) && (rctl & E1000_RCTL_LPE)) {
2916 e1e_rphy(hw, PHY_REG(770, 26), &phy_data);
2918 phy_data |= (1 << 2);
2919 e1e_wphy(hw, PHY_REG(770, 26), phy_data);
2921 e1e_rphy(hw, 22, &phy_data);
2923 phy_data |= (1 << 14);
2924 e1e_wphy(hw, 0x10, 0x2823);
2925 e1e_wphy(hw, 0x11, 0x0003);
2926 e1e_wphy(hw, 22, phy_data);
2929 /* Setup buffer sizes */
2930 rctl &= ~E1000_RCTL_SZ_4096;
2931 rctl |= E1000_RCTL_BSEX;
2932 switch (adapter->rx_buffer_len) {
2935 rctl |= E1000_RCTL_SZ_2048;
2936 rctl &= ~E1000_RCTL_BSEX;
2939 rctl |= E1000_RCTL_SZ_4096;
2942 rctl |= E1000_RCTL_SZ_8192;
2945 rctl |= E1000_RCTL_SZ_16384;
2949 /* Enable Extended Status in all Receive Descriptors */
2950 rfctl = er32(RFCTL);
2951 rfctl |= E1000_RFCTL_EXTEN;
2955 * 82571 and greater support packet-split where the protocol
2956 * header is placed in skb->data and the packet data is
2957 * placed in pages hanging off of skb_shinfo(skb)->nr_frags.
2958 * In the case of a non-split, skb->data is linearly filled,
2959 * followed by the page buffers. Therefore, skb->data is
2960 * sized to hold the largest protocol header.
2962 * allocations using alloc_page take too long for regular MTU
2963 * so only enable packet split for jumbo frames
2965 * Using pages when the page size is greater than 16k wastes
2966 * a lot of memory, since we allocate 3 pages at all times
2969 pages = PAGE_USE_COUNT(adapter->netdev->mtu);
2970 if ((pages <= 3) && (PAGE_SIZE <= 16384) && (rctl & E1000_RCTL_LPE))
2971 adapter->rx_ps_pages = pages;
2973 adapter->rx_ps_pages = 0;
2975 if (adapter->rx_ps_pages) {
2978 /* Enable Packet split descriptors */
2979 rctl |= E1000_RCTL_DTYP_PS;
2981 psrctl |= adapter->rx_ps_bsize0 >>
2982 E1000_PSRCTL_BSIZE0_SHIFT;
2984 switch (adapter->rx_ps_pages) {
2986 psrctl |= PAGE_SIZE <<
2987 E1000_PSRCTL_BSIZE3_SHIFT;
2989 psrctl |= PAGE_SIZE <<
2990 E1000_PSRCTL_BSIZE2_SHIFT;
2992 psrctl |= PAGE_SIZE >>
2993 E1000_PSRCTL_BSIZE1_SHIFT;
2997 ew32(PSRCTL, psrctl);
3000 /* This is useful for sniffing bad packets. */
3001 if (adapter->netdev->features & NETIF_F_RXALL) {
3002 /* UPE and MPE will be handled by normal PROMISC logic
3003 * in e1000e_set_rx_mode */
3004 rctl |= (E1000_RCTL_SBP | /* Receive bad packets */
3005 E1000_RCTL_BAM | /* RX All Bcast Pkts */
3006 E1000_RCTL_PMCF); /* RX All MAC Ctrl Pkts */
3008 rctl &= ~(E1000_RCTL_VFE | /* Disable VLAN filter */
3009 E1000_RCTL_DPF | /* Allow filtered pause */
3010 E1000_RCTL_CFIEN); /* Dis VLAN CFIEN Filter */
3011 /* Do not mess with E1000_CTRL_VME, it affects transmit as well,
3012 * and that breaks VLANs.
3017 /* just started the receive unit, no need to restart */
3018 adapter->flags &= ~FLAG_RX_RESTART_NOW;
3022 * e1000_configure_rx - Configure Receive Unit after Reset
3023 * @adapter: board private structure
3025 * Configure the Rx unit of the MAC after a reset.
3027 static void e1000_configure_rx(struct e1000_adapter *adapter)
3029 struct e1000_hw *hw = &adapter->hw;
3030 struct e1000_ring *rx_ring = adapter->rx_ring;
3032 u32 rdlen, rctl, rxcsum, ctrl_ext;
3034 if (adapter->rx_ps_pages) {
3035 /* this is a 32 byte descriptor */
3036 rdlen = rx_ring->count *
3037 sizeof(union e1000_rx_desc_packet_split);
3038 adapter->clean_rx = e1000_clean_rx_irq_ps;
3039 adapter->alloc_rx_buf = e1000_alloc_rx_buffers_ps;
3040 } else if (adapter->netdev->mtu > ETH_FRAME_LEN + ETH_FCS_LEN) {
3041 rdlen = rx_ring->count * sizeof(union e1000_rx_desc_extended);
3042 adapter->clean_rx = e1000_clean_jumbo_rx_irq;
3043 adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers;
3045 rdlen = rx_ring->count * sizeof(union e1000_rx_desc_extended);
3046 adapter->clean_rx = e1000_clean_rx_irq;
3047 adapter->alloc_rx_buf = e1000_alloc_rx_buffers;
3050 /* disable receives while setting up the descriptors */
3052 if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX))
3053 ew32(RCTL, rctl & ~E1000_RCTL_EN);
3055 usleep_range(10000, 20000);
3057 if (adapter->flags2 & FLAG2_DMA_BURST) {
3059 * set the writeback threshold (only takes effect if the RDTR
3060 * is set). set GRAN=1 and write back up to 0x4 worth, and
3061 * enable prefetching of 0x20 Rx descriptors
3067 ew32(RXDCTL(0), E1000_RXDCTL_DMA_BURST_ENABLE);
3068 ew32(RXDCTL(1), E1000_RXDCTL_DMA_BURST_ENABLE);
3071 * override the delay timers for enabling bursting, only if
3072 * the value was not set by the user via module options
3074 if (adapter->rx_int_delay == DEFAULT_RDTR)
3075 adapter->rx_int_delay = BURST_RDTR;
3076 if (adapter->rx_abs_int_delay == DEFAULT_RADV)
3077 adapter->rx_abs_int_delay = BURST_RADV;
3080 /* set the Receive Delay Timer Register */
3081 ew32(RDTR, adapter->rx_int_delay);
3083 /* irq moderation */
3084 ew32(RADV, adapter->rx_abs_int_delay);
3085 if ((adapter->itr_setting != 0) && (adapter->itr != 0))
3086 e1000e_write_itr(adapter, adapter->itr);
3088 ctrl_ext = er32(CTRL_EXT);
3089 /* Auto-Mask interrupts upon ICR access */
3090 ctrl_ext |= E1000_CTRL_EXT_IAME;
3091 ew32(IAM, 0xffffffff);
3092 ew32(CTRL_EXT, ctrl_ext);
3096 * Setup the HW Rx Head and Tail Descriptor Pointers and
3097 * the Base and Length of the Rx Descriptor Ring
3099 rdba = rx_ring->dma;
3100 ew32(RDBAL(0), (rdba & DMA_BIT_MASK(32)));
3101 ew32(RDBAH(0), (rdba >> 32));
3102 ew32(RDLEN(0), rdlen);
3105 rx_ring->head = adapter->hw.hw_addr + E1000_RDH(0);
3106 rx_ring->tail = adapter->hw.hw_addr + E1000_RDT(0);
3108 /* Enable Receive Checksum Offload for TCP and UDP */
3109 rxcsum = er32(RXCSUM);
3110 if (adapter->netdev->features & NETIF_F_RXCSUM)
3111 rxcsum |= E1000_RXCSUM_TUOFL;
3113 rxcsum &= ~E1000_RXCSUM_TUOFL;
3114 ew32(RXCSUM, rxcsum);
3116 if (adapter->hw.mac.type == e1000_pch2lan) {
3118 * With jumbo frames, excessive C-state transition
3119 * latencies result in dropped transactions.
3121 if (adapter->netdev->mtu > ETH_DATA_LEN) {
3122 u32 rxdctl = er32(RXDCTL(0));
3123 ew32(RXDCTL(0), rxdctl | 0x3);
3124 pm_qos_update_request(&adapter->netdev->pm_qos_req, 55);
3126 pm_qos_update_request(&adapter->netdev->pm_qos_req,
3127 PM_QOS_DEFAULT_VALUE);
3131 /* Enable Receives */
3136 * e1000e_write_mc_addr_list - write multicast addresses to MTA
3137 * @netdev: network interface device structure
3139 * Writes multicast address list to the MTA hash table.
3140 * Returns: -ENOMEM on failure
3141 * 0 on no addresses written
3142 * X on writing X addresses to MTA
3144 static int e1000e_write_mc_addr_list(struct net_device *netdev)
3146 struct e1000_adapter *adapter = netdev_priv(netdev);
3147 struct e1000_hw *hw = &adapter->hw;
3148 struct netdev_hw_addr *ha;
3152 if (netdev_mc_empty(netdev)) {
3153 /* nothing to program, so clear mc list */
3154 hw->mac.ops.update_mc_addr_list(hw, NULL, 0);
3158 mta_list = kzalloc(netdev_mc_count(netdev) * ETH_ALEN, GFP_ATOMIC);
3162 /* update_mc_addr_list expects a packed array of only addresses. */
3164 netdev_for_each_mc_addr(ha, netdev)
3165 memcpy(mta_list + (i++ * ETH_ALEN), ha->addr, ETH_ALEN);
3167 hw->mac.ops.update_mc_addr_list(hw, mta_list, i);
3170 return netdev_mc_count(netdev);
3174 * e1000e_write_uc_addr_list - write unicast addresses to RAR table
3175 * @netdev: network interface device structure
3177 * Writes unicast address list to the RAR table.
3178 * Returns: -ENOMEM on failure/insufficient address space
3179 * 0 on no addresses written
3180 * X on writing X addresses to the RAR table
3182 static int e1000e_write_uc_addr_list(struct net_device *netdev)
3184 struct e1000_adapter *adapter = netdev_priv(netdev);
3185 struct e1000_hw *hw = &adapter->hw;
3186 unsigned int rar_entries = hw->mac.rar_entry_count;
3189 /* save a rar entry for our hardware address */
3192 /* save a rar entry for the LAA workaround */
3193 if (adapter->flags & FLAG_RESET_OVERWRITES_LAA)
3196 /* return ENOMEM indicating insufficient memory for addresses */
3197 if (netdev_uc_count(netdev) > rar_entries)
3200 if (!netdev_uc_empty(netdev) && rar_entries) {
3201 struct netdev_hw_addr *ha;
3204 * write the addresses in reverse order to avoid write
3207 netdev_for_each_uc_addr(ha, netdev) {
3210 hw->mac.ops.rar_set(hw, ha->addr, rar_entries--);
3215 /* zero out the remaining RAR entries not used above */
3216 for (; rar_entries > 0; rar_entries--) {
3217 ew32(RAH(rar_entries), 0);
3218 ew32(RAL(rar_entries), 0);
3226 * e1000e_set_rx_mode - secondary unicast, Multicast and Promiscuous mode set
3227 * @netdev: network interface device structure
3229 * The ndo_set_rx_mode entry point is called whenever the unicast or multicast
3230 * address list or the network interface flags are updated. This routine is
3231 * responsible for configuring the hardware for proper unicast, multicast,
3232 * promiscuous mode, and all-multi behavior.
3234 static void e1000e_set_rx_mode(struct net_device *netdev)
3236 struct e1000_adapter *adapter = netdev_priv(netdev);
3237 struct e1000_hw *hw = &adapter->hw;
3240 /* Check for Promiscuous and All Multicast modes */
3243 /* clear the affected bits */
3244 rctl &= ~(E1000_RCTL_UPE | E1000_RCTL_MPE);
3246 if (netdev->flags & IFF_PROMISC) {
3247 rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
3248 /* Do not hardware filter VLANs in promisc mode */
3249 e1000e_vlan_filter_disable(adapter);
3253 if (netdev->flags & IFF_ALLMULTI) {
3254 rctl |= E1000_RCTL_MPE;
3257 * Write addresses to the MTA, if the attempt fails
3258 * then we should just turn on promiscuous mode so
3259 * that we can at least receive multicast traffic
3261 count = e1000e_write_mc_addr_list(netdev);
3263 rctl |= E1000_RCTL_MPE;
3265 e1000e_vlan_filter_enable(adapter);
3267 * Write addresses to available RAR registers, if there is not
3268 * sufficient space to store all the addresses then enable
3269 * unicast promiscuous mode
3271 count = e1000e_write_uc_addr_list(netdev);
3273 rctl |= E1000_RCTL_UPE;
3278 if (netdev->features & NETIF_F_HW_VLAN_RX)
3279 e1000e_vlan_strip_enable(adapter);
3281 e1000e_vlan_strip_disable(adapter);
3284 static void e1000e_setup_rss_hash(struct e1000_adapter *adapter)
3286 struct e1000_hw *hw = &adapter->hw;
3289 static const u32 rsskey[10] = {
3290 0xda565a6d, 0xc20e5b25, 0x3d256741, 0xb08fa343, 0xcb2bcad0,
3291 0xb4307bae, 0xa32dcb77, 0x0cf23080, 0x3bb7426a, 0xfa01acbe
3294 /* Fill out hash function seed */
3295 for (i = 0; i < 10; i++)
3296 ew32(RSSRK(i), rsskey[i]);
3298 /* Direct all traffic to queue 0 */
3299 for (i = 0; i < 32; i++)
3303 * Disable raw packet checksumming so that RSS hash is placed in
3304 * descriptor on writeback.
3306 rxcsum = er32(RXCSUM);
3307 rxcsum |= E1000_RXCSUM_PCSD;
3309 ew32(RXCSUM, rxcsum);
3311 mrqc = (E1000_MRQC_RSS_FIELD_IPV4 |
3312 E1000_MRQC_RSS_FIELD_IPV4_TCP |
3313 E1000_MRQC_RSS_FIELD_IPV6 |
3314 E1000_MRQC_RSS_FIELD_IPV6_TCP |
3315 E1000_MRQC_RSS_FIELD_IPV6_TCP_EX);
3321 * e1000_configure - configure the hardware for Rx and Tx
3322 * @adapter: private board structure
3324 static void e1000_configure(struct e1000_adapter *adapter)
3326 struct e1000_ring *rx_ring = adapter->rx_ring;
3328 e1000e_set_rx_mode(adapter->netdev);
3330 e1000_restore_vlan(adapter);
3331 e1000_init_manageability_pt(adapter);
3333 e1000_configure_tx(adapter);
3335 if (adapter->netdev->features & NETIF_F_RXHASH)
3336 e1000e_setup_rss_hash(adapter);
3337 e1000_setup_rctl(adapter);
3338 e1000_configure_rx(adapter);
3339 adapter->alloc_rx_buf(rx_ring, e1000_desc_unused(rx_ring), GFP_KERNEL);
3343 * e1000e_power_up_phy - restore link in case the phy was powered down
3344 * @adapter: address of board private structure
3346 * The phy may be powered down to save power and turn off link when the
3347 * driver is unloaded and wake on lan is not enabled (among others)
3348 * *** this routine MUST be followed by a call to e1000e_reset ***
3350 void e1000e_power_up_phy(struct e1000_adapter *adapter)
3352 if (adapter->hw.phy.ops.power_up)
3353 adapter->hw.phy.ops.power_up(&adapter->hw);
3355 adapter->hw.mac.ops.setup_link(&adapter->hw);
3359 * e1000_power_down_phy - Power down the PHY
3361 * Power down the PHY so no link is implied when interface is down.
3362 * The PHY cannot be powered down if management or WoL is active.
3364 static void e1000_power_down_phy(struct e1000_adapter *adapter)
3366 /* WoL is enabled */
3370 if (adapter->hw.phy.ops.power_down)
3371 adapter->hw.phy.ops.power_down(&adapter->hw);
3375 * e1000e_reset - bring the hardware into a known good state
3377 * This function boots the hardware and enables some settings that
3378 * require a configuration cycle of the hardware - those cannot be
3379 * set/changed during runtime. After reset the device needs to be
3380 * properly configured for Rx, Tx etc.
3382 void e1000e_reset(struct e1000_adapter *adapter)
3384 struct e1000_mac_info *mac = &adapter->hw.mac;
3385 struct e1000_fc_info *fc = &adapter->hw.fc;
3386 struct e1000_hw *hw = &adapter->hw;
3387 u32 tx_space, min_tx_space, min_rx_space;
3388 u32 pba = adapter->pba;
3391 /* reset Packet Buffer Allocation to default */
3394 if (adapter->max_frame_size > ETH_FRAME_LEN + ETH_FCS_LEN) {
3396 * To maintain wire speed transmits, the Tx FIFO should be
3397 * large enough to accommodate two full transmit packets,
3398 * rounded up to the next 1KB and expressed in KB. Likewise,
3399 * the Rx FIFO should be large enough to accommodate at least
3400 * one full receive packet and is similarly rounded up and
3404 /* upper 16 bits has Tx packet buffer allocation size in KB */
3405 tx_space = pba >> 16;
3406 /* lower 16 bits has Rx packet buffer allocation size in KB */
3409 * the Tx fifo also stores 16 bytes of information about the Tx
3410 * but don't include ethernet FCS because hardware appends it
3412 min_tx_space = (adapter->max_frame_size +
3413 sizeof(struct e1000_tx_desc) -
3415 min_tx_space = ALIGN(min_tx_space, 1024);
3416 min_tx_space >>= 10;
3417 /* software strips receive CRC, so leave room for it */
3418 min_rx_space = adapter->max_frame_size;
3419 min_rx_space = ALIGN(min_rx_space, 1024);
3420 min_rx_space >>= 10;
3423 * If current Tx allocation is less than the min Tx FIFO size,
3424 * and the min Tx FIFO size is less than the current Rx FIFO
3425 * allocation, take space away from current Rx allocation
3427 if ((tx_space < min_tx_space) &&
3428 ((min_tx_space - tx_space) < pba)) {
3429 pba -= min_tx_space - tx_space;
3432 * if short on Rx space, Rx wins and must trump Tx
3433 * adjustment or use Early Receive if available
3435 if (pba < min_rx_space)
3443 * flow control settings
3445 * The high water mark must be low enough to fit one full frame
3446 * (or the size used for early receive) above it in the Rx FIFO.
3447 * Set it to the lower of:
3448 * - 90% of the Rx FIFO size, and
3449 * - the full Rx FIFO size minus one full frame
3451 if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME)
3452 fc->pause_time = 0xFFFF;
3454 fc->pause_time = E1000_FC_PAUSE_TIME;
3455 fc->send_xon = true;
3456 fc->current_mode = fc->requested_mode;
3458 switch (hw->mac.type) {
3460 case e1000_ich10lan:
3461 if (adapter->netdev->mtu > ETH_DATA_LEN) {
3464 fc->high_water = 0x2800;
3465 fc->low_water = fc->high_water - 8;
3470 hwm = min(((pba << 10) * 9 / 10),
3471 ((pba << 10) - adapter->max_frame_size));
3473 fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
3474 fc->low_water = fc->high_water - 8;
3478 * Workaround PCH LOM adapter hangs with certain network
3479 * loads. If hangs persist, try disabling Tx flow control.
3481 if (adapter->netdev->mtu > ETH_DATA_LEN) {
3482 fc->high_water = 0x3500;
3483 fc->low_water = 0x1500;
3485 fc->high_water = 0x5000;
3486 fc->low_water = 0x3000;
3488 fc->refresh_time = 0x1000;
3492 fc->high_water = 0x05C20;
3493 fc->low_water = 0x05048;
3494 fc->pause_time = 0x0650;
3495 fc->refresh_time = 0x0400;
3496 if (adapter->netdev->mtu > ETH_DATA_LEN) {
3504 * Disable Adaptive Interrupt Moderation if 2 full packets cannot
3505 * fit in receive buffer.
3507 if (adapter->itr_setting & 0x3) {
3508 if ((adapter->max_frame_size * 2) > (pba << 10)) {
3509 if (!(adapter->flags2 & FLAG2_DISABLE_AIM)) {
3510 dev_info(&adapter->pdev->dev,
3511 "Interrupt Throttle Rate turned off\n");
3512 adapter->flags2 |= FLAG2_DISABLE_AIM;
3513 e1000e_write_itr(adapter, 0);
3515 } else if (adapter->flags2 & FLAG2_DISABLE_AIM) {
3516 dev_info(&adapter->pdev->dev,
3517 "Interrupt Throttle Rate turned on\n");
3518 adapter->flags2 &= ~FLAG2_DISABLE_AIM;
3519 adapter->itr = 20000;
3520 e1000e_write_itr(adapter, adapter->itr);
3524 /* Allow time for pending master requests to run */
3525 mac->ops.reset_hw(hw);
3528 * For parts with AMT enabled, let the firmware know
3529 * that the network interface is in control
3531 if (adapter->flags & FLAG_HAS_AMT)
3532 e1000e_get_hw_control(adapter);
3536 if (mac->ops.init_hw(hw))
3537 e_err("Hardware Error\n");
3539 e1000_update_mng_vlan(adapter);
3541 /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
3542 ew32(VET, ETH_P_8021Q);
3544 e1000e_reset_adaptive(hw);
3546 if (!netif_running(adapter->netdev) &&
3547 !test_bit(__E1000_TESTING, &adapter->state)) {
3548 e1000_power_down_phy(adapter);
3552 e1000_get_phy_info(hw);
3554 if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN) &&
3555 !(adapter->flags & FLAG_SMART_POWER_DOWN)) {
3558 * speed up time to link by disabling smart power down, ignore
3559 * the return value of this function because there is nothing
3560 * different we would do if it failed
3562 e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
3563 phy_data &= ~IGP02E1000_PM_SPD;
3564 e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
3568 int e1000e_up(struct e1000_adapter *adapter)
3570 struct e1000_hw *hw = &adapter->hw;
3572 /* hardware has been reset, we need to reload some things */
3573 e1000_configure(adapter);
3575 clear_bit(__E1000_DOWN, &adapter->state);
3577 if (adapter->msix_entries)
3578 e1000_configure_msix(adapter);
3579 e1000_irq_enable(adapter);
3581 netif_start_queue(adapter->netdev);
3583 /* fire a link change interrupt to start the watchdog */
3584 if (adapter->msix_entries)
3585 ew32(ICS, E1000_ICS_LSC | E1000_ICR_OTHER);
3587 ew32(ICS, E1000_ICS_LSC);
3592 static void e1000e_flush_descriptors(struct e1000_adapter *adapter)
3594 struct e1000_hw *hw = &adapter->hw;
3596 if (!(adapter->flags2 & FLAG2_DMA_BURST))
3599 /* flush pending descriptor writebacks to memory */
3600 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
3601 ew32(RDTR, adapter->rx_int_delay | E1000_RDTR_FPD);
3603 /* execute the writes immediately */
3607 * due to rare timing issues, write to TIDV/RDTR again to ensure the
3608 * write is successful
3610 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
3611 ew32(RDTR, adapter->rx_int_delay | E1000_RDTR_FPD);
3613 /* execute the writes immediately */
3617 static void e1000e_update_stats(struct e1000_adapter *adapter);
3619 void e1000e_down(struct e1000_adapter *adapter)
3621 struct net_device *netdev = adapter->netdev;
3622 struct e1000_hw *hw = &adapter->hw;
3626 * signal that we're down so the interrupt handler does not
3627 * reschedule our watchdog timer
3629 set_bit(__E1000_DOWN, &adapter->state);
3631 /* disable receives in the hardware */
3633 if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX))
3634 ew32(RCTL, rctl & ~E1000_RCTL_EN);
3635 /* flush and sleep below */
3637 netif_stop_queue(netdev);
3639 /* disable transmits in the hardware */
3641 tctl &= ~E1000_TCTL_EN;
3644 /* flush both disables and wait for them to finish */
3646 usleep_range(10000, 20000);
3648 e1000_irq_disable(adapter);
3650 del_timer_sync(&adapter->watchdog_timer);
3651 del_timer_sync(&adapter->phy_info_timer);
3653 netif_carrier_off(netdev);
3655 spin_lock(&adapter->stats64_lock);
3656 e1000e_update_stats(adapter);
3657 spin_unlock(&adapter->stats64_lock);
3659 e1000e_flush_descriptors(adapter);
3660 e1000_clean_tx_ring(adapter->tx_ring);
3661 e1000_clean_rx_ring(adapter->rx_ring);
3663 adapter->link_speed = 0;
3664 adapter->link_duplex = 0;
3666 if (!pci_channel_offline(adapter->pdev))
3667 e1000e_reset(adapter);
3670 * TODO: for power management, we could drop the link and
3671 * pci_disable_device here.
3675 void e1000e_reinit_locked(struct e1000_adapter *adapter)
3678 while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
3679 usleep_range(1000, 2000);
3680 e1000e_down(adapter);
3682 clear_bit(__E1000_RESETTING, &adapter->state);
3686 * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
3687 * @adapter: board private structure to initialize
3689 * e1000_sw_init initializes the Adapter private data structure.
3690 * Fields are initialized based on PCI device information and
3691 * OS network device settings (MTU size).
3693 static int __devinit e1000_sw_init(struct e1000_adapter *adapter)
3695 struct net_device *netdev = adapter->netdev;
3697 adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN;
3698 adapter->rx_ps_bsize0 = 128;
3699 adapter->max_frame_size = netdev->mtu + ETH_HLEN + ETH_FCS_LEN;
3700 adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN;
3701 adapter->tx_ring_count = E1000_DEFAULT_TXD;
3702 adapter->rx_ring_count = E1000_DEFAULT_RXD;
3704 spin_lock_init(&adapter->stats64_lock);
3706 e1000e_set_interrupt_capability(adapter);
3708 if (e1000_alloc_queues(adapter))
3711 /* Explicitly disable IRQ since the NIC can be in any state. */
3712 e1000_irq_disable(adapter);
3714 set_bit(__E1000_DOWN, &adapter->state);
3719 * e1000_intr_msi_test - Interrupt Handler
3720 * @irq: interrupt number
3721 * @data: pointer to a network interface device structure
3723 static irqreturn_t e1000_intr_msi_test(int irq, void *data)
3725 struct net_device *netdev = data;
3726 struct e1000_adapter *adapter = netdev_priv(netdev);
3727 struct e1000_hw *hw = &adapter->hw;
3728 u32 icr = er32(ICR);
3730 e_dbg("icr is %08X\n", icr);
3731 if (icr & E1000_ICR_RXSEQ) {
3732 adapter->flags &= ~FLAG_MSI_TEST_FAILED;
3740 * e1000_test_msi_interrupt - Returns 0 for successful test
3741 * @adapter: board private struct
3743 * code flow taken from tg3.c
3745 static int e1000_test_msi_interrupt(struct e1000_adapter *adapter)
3747 struct net_device *netdev = adapter->netdev;
3748 struct e1000_hw *hw = &adapter->hw;
3751 /* poll_enable hasn't been called yet, so don't need disable */
3752 /* clear any pending events */
3755 /* free the real vector and request a test handler */
3756 e1000_free_irq(adapter);
3757 e1000e_reset_interrupt_capability(adapter);
3759 /* Assume that the test fails, if it succeeds then the test
3760 * MSI irq handler will unset this flag */
3761 adapter->flags |= FLAG_MSI_TEST_FAILED;
3763 err = pci_enable_msi(adapter->pdev);
3765 goto msi_test_failed;
3767 err = request_irq(adapter->pdev->irq, e1000_intr_msi_test, 0,
3768 netdev->name, netdev);
3770 pci_disable_msi(adapter->pdev);
3771 goto msi_test_failed;
3776 e1000_irq_enable(adapter);
3778 /* fire an unusual interrupt on the test handler */
3779 ew32(ICS, E1000_ICS_RXSEQ);
3783 e1000_irq_disable(adapter);
3787 if (adapter->flags & FLAG_MSI_TEST_FAILED) {
3788 adapter->int_mode = E1000E_INT_MODE_LEGACY;
3789 e_info("MSI interrupt test failed, using legacy interrupt.\n");
3791 e_dbg("MSI interrupt test succeeded!\n");
3794 free_irq(adapter->pdev->irq, netdev);
3795 pci_disable_msi(adapter->pdev);
3798 e1000e_set_interrupt_capability(adapter);
3799 return e1000_request_irq(adapter);
3803 * e1000_test_msi - Returns 0 if MSI test succeeds or INTx mode is restored
3804 * @adapter: board private struct
3806 * code flow taken from tg3.c, called with e1000 interrupts disabled.
3808 static int e1000_test_msi(struct e1000_adapter *adapter)
3813 if (!(adapter->flags & FLAG_MSI_ENABLED))
3816 /* disable SERR in case the MSI write causes a master abort */
3817 pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd);
3818 if (pci_cmd & PCI_COMMAND_SERR)
3819 pci_write_config_word(adapter->pdev, PCI_COMMAND,
3820 pci_cmd & ~PCI_COMMAND_SERR);
3822 err = e1000_test_msi_interrupt(adapter);
3824 /* re-enable SERR */
3825 if (pci_cmd & PCI_COMMAND_SERR) {
3826 pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd);
3827 pci_cmd |= PCI_COMMAND_SERR;
3828 pci_write_config_word(adapter->pdev, PCI_COMMAND, pci_cmd);
3835 * e1000_open - Called when a network interface is made active
3836 * @netdev: network interface device structure
3838 * Returns 0 on success, negative value on failure
3840 * The open entry point is called when a network interface is made
3841 * active by the system (IFF_UP). At this point all resources needed
3842 * for transmit and receive operations are allocated, the interrupt
3843 * handler is registered with the OS, the watchdog timer is started,
3844 * and the stack is notified that the interface is ready.
3846 static int e1000_open(struct net_device *netdev)
3848 struct e1000_adapter *adapter = netdev_priv(netdev);
3849 struct e1000_hw *hw = &adapter->hw;
3850 struct pci_dev *pdev = adapter->pdev;
3853 /* disallow open during test */
3854 if (test_bit(__E1000_TESTING, &adapter->state))
3857 pm_runtime_get_sync(&pdev->dev);
3859 netif_carrier_off(netdev);
3861 /* allocate transmit descriptors */
3862 err = e1000e_setup_tx_resources(adapter->tx_ring);
3866 /* allocate receive descriptors */
3867 err = e1000e_setup_rx_resources(adapter->rx_ring);
3872 * If AMT is enabled, let the firmware know that the network
3873 * interface is now open and reset the part to a known state.
3875 if (adapter->flags & FLAG_HAS_AMT) {
3876 e1000e_get_hw_control(adapter);
3877 e1000e_reset(adapter);
3880 e1000e_power_up_phy(adapter);
3882 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
3883 if ((adapter->hw.mng_cookie.status &
3884 E1000_MNG_DHCP_COOKIE_STATUS_VLAN))
3885 e1000_update_mng_vlan(adapter);
3887 /* DMA latency requirement to workaround jumbo issue */
3888 if (adapter->hw.mac.type == e1000_pch2lan)
3889 pm_qos_add_request(&adapter->netdev->pm_qos_req,
3890 PM_QOS_CPU_DMA_LATENCY,
3891 PM_QOS_DEFAULT_VALUE);
3894 * before we allocate an interrupt, we must be ready to handle it.
3895 * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
3896 * as soon as we call pci_request_irq, so we have to setup our
3897 * clean_rx handler before we do so.
3899 e1000_configure(adapter);
3901 err = e1000_request_irq(adapter);
3906 * Work around PCIe errata with MSI interrupts causing some chipsets to
3907 * ignore e1000e MSI messages, which means we need to test our MSI
3910 if (adapter->int_mode != E1000E_INT_MODE_LEGACY) {
3911 err = e1000_test_msi(adapter);
3913 e_err("Interrupt allocation failed\n");
3918 /* From here on the code is the same as e1000e_up() */
3919 clear_bit(__E1000_DOWN, &adapter->state);
3921 napi_enable(&adapter->napi);
3923 e1000_irq_enable(adapter);
3925 adapter->tx_hang_recheck = false;
3926 netif_start_queue(netdev);
3928 adapter->idle_check = true;
3929 pm_runtime_put(&pdev->dev);
3931 /* fire a link status change interrupt to start the watchdog */
3932 if (adapter->msix_entries)
3933 ew32(ICS, E1000_ICS_LSC | E1000_ICR_OTHER);
3935 ew32(ICS, E1000_ICS_LSC);
3940 e1000e_release_hw_control(adapter);
3941 e1000_power_down_phy(adapter);
3942 e1000e_free_rx_resources(adapter->rx_ring);
3944 e1000e_free_tx_resources(adapter->tx_ring);
3946 e1000e_reset(adapter);
3947 pm_runtime_put_sync(&pdev->dev);
3953 * e1000_close - Disables a network interface
3954 * @netdev: network interface device structure
3956 * Returns 0, this is not allowed to fail
3958 * The close entry point is called when an interface is de-activated
3959 * by the OS. The hardware is still under the drivers control, but
3960 * needs to be disabled. A global MAC reset is issued to stop the
3961 * hardware, and all transmit and receive resources are freed.
3963 static int e1000_close(struct net_device *netdev)
3965 struct e1000_adapter *adapter = netdev_priv(netdev);
3966 struct pci_dev *pdev = adapter->pdev;
3967 int count = E1000_CHECK_RESET_COUNT;
3969 while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
3970 usleep_range(10000, 20000);
3972 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
3974 pm_runtime_get_sync(&pdev->dev);
3976 napi_disable(&adapter->napi);
3978 if (!test_bit(__E1000_DOWN, &adapter->state)) {
3979 e1000e_down(adapter);
3980 e1000_free_irq(adapter);
3982 e1000_power_down_phy(adapter);
3984 e1000e_free_tx_resources(adapter->tx_ring);
3985 e1000e_free_rx_resources(adapter->rx_ring);
3988 * kill manageability vlan ID if supported, but not if a vlan with
3989 * the same ID is registered on the host OS (let 8021q kill it)
3991 if (adapter->hw.mng_cookie.status &
3992 E1000_MNG_DHCP_COOKIE_STATUS_VLAN)
3993 e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
3996 * If AMT is enabled, let the firmware know that the network
3997 * interface is now closed
3999 if ((adapter->flags & FLAG_HAS_AMT) &&
4000 !test_bit(__E1000_TESTING, &adapter->state))
4001 e1000e_release_hw_control(adapter);
4003 if (adapter->hw.mac.type == e1000_pch2lan)
4004 pm_qos_remove_request(&adapter->netdev->pm_qos_req);
4006 pm_runtime_put_sync(&pdev->dev);
4011 * e1000_set_mac - Change the Ethernet Address of the NIC
4012 * @netdev: network interface device structure
4013 * @p: pointer to an address structure
4015 * Returns 0 on success, negative on failure
4017 static int e1000_set_mac(struct net_device *netdev, void *p)
4019 struct e1000_adapter *adapter = netdev_priv(netdev);
4020 struct e1000_hw *hw = &adapter->hw;
4021 struct sockaddr *addr = p;
4023 if (!is_valid_ether_addr(addr->sa_data))
4024 return -EADDRNOTAVAIL;
4026 memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
4027 memcpy(adapter->hw.mac.addr, addr->sa_data, netdev->addr_len);
4029 hw->mac.ops.rar_set(&adapter->hw, adapter->hw.mac.addr, 0);
4031 if (adapter->flags & FLAG_RESET_OVERWRITES_LAA) {
4032 /* activate the work around */
4033 e1000e_set_laa_state_82571(&adapter->hw, 1);
4036 * Hold a copy of the LAA in RAR[14] This is done so that
4037 * between the time RAR[0] gets clobbered and the time it
4038 * gets fixed (in e1000_watchdog), the actual LAA is in one
4039 * of the RARs and no incoming packets directed to this port
4040 * are dropped. Eventually the LAA will be in RAR[0] and
4043 hw->mac.ops.rar_set(&adapter->hw, adapter->hw.mac.addr,
4044 adapter->hw.mac.rar_entry_count - 1);
4051 * e1000e_update_phy_task - work thread to update phy
4052 * @work: pointer to our work struct
4054 * this worker thread exists because we must acquire a
4055 * semaphore to read the phy, which we could msleep while
4056 * waiting for it, and we can't msleep in a timer.
4058 static void e1000e_update_phy_task(struct work_struct *work)
4060 struct e1000_adapter *adapter = container_of(work,
4061 struct e1000_adapter, update_phy_task);
4063 if (test_bit(__E1000_DOWN, &adapter->state))
4066 e1000_get_phy_info(&adapter->hw);
4070 * Need to wait a few seconds after link up to get diagnostic information from
4073 static void e1000_update_phy_info(unsigned long data)
4075 struct e1000_adapter *adapter = (struct e1000_adapter *) data;
4077 if (test_bit(__E1000_DOWN, &adapter->state))
4080 schedule_work(&adapter->update_phy_task);
4084 * e1000e_update_phy_stats - Update the PHY statistics counters
4085 * @adapter: board private structure
4087 * Read/clear the upper 16-bit PHY registers and read/accumulate lower
4089 static void e1000e_update_phy_stats(struct e1000_adapter *adapter)
4091 struct e1000_hw *hw = &adapter->hw;
4095 ret_val = hw->phy.ops.acquire(hw);
4100 * A page set is expensive so check if already on desired page.
4101 * If not, set to the page with the PHY status registers.
4104 ret_val = e1000e_read_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
4108 if (phy_data != (HV_STATS_PAGE << IGP_PAGE_SHIFT)) {
4109 ret_val = hw->phy.ops.set_page(hw,
4110 HV_STATS_PAGE << IGP_PAGE_SHIFT);
4115 /* Single Collision Count */
4116 hw->phy.ops.read_reg_page(hw, HV_SCC_UPPER, &phy_data);
4117 ret_val = hw->phy.ops.read_reg_page(hw, HV_SCC_LOWER, &phy_data);
4119 adapter->stats.scc += phy_data;
4121 /* Excessive Collision Count */
4122 hw->phy.ops.read_reg_page(hw, HV_ECOL_UPPER, &phy_data);
4123 ret_val = hw->phy.ops.read_reg_page(hw, HV_ECOL_LOWER, &phy_data);
4125 adapter->stats.ecol += phy_data;
4127 /* Multiple Collision Count */
4128 hw->phy.ops.read_reg_page(hw, HV_MCC_UPPER, &phy_data);
4129 ret_val = hw->phy.ops.read_reg_page(hw, HV_MCC_LOWER, &phy_data);
4131 adapter->stats.mcc += phy_data;
4133 /* Late Collision Count */
4134 hw->phy.ops.read_reg_page(hw, HV_LATECOL_UPPER, &phy_data);
4135 ret_val = hw->phy.ops.read_reg_page(hw, HV_LATECOL_LOWER, &phy_data);
4137 adapter->stats.latecol += phy_data;
4139 /* Collision Count - also used for adaptive IFS */
4140 hw->phy.ops.read_reg_page(hw, HV_COLC_UPPER, &phy_data);
4141 ret_val = hw->phy.ops.read_reg_page(hw, HV_COLC_LOWER, &phy_data);
4143 hw->mac.collision_delta = phy_data;
4146 hw->phy.ops.read_reg_page(hw, HV_DC_UPPER, &phy_data);
4147 ret_val = hw->phy.ops.read_reg_page(hw, HV_DC_LOWER, &phy_data);
4149 adapter->stats.dc += phy_data;
4151 /* Transmit with no CRS */
4152 hw->phy.ops.read_reg_page(hw, HV_TNCRS_UPPER, &phy_data);
4153 ret_val = hw->phy.ops.read_reg_page(hw, HV_TNCRS_LOWER, &phy_data);
4155 adapter->stats.tncrs += phy_data;
4158 hw->phy.ops.release(hw);
4162 * e1000e_update_stats - Update the board statistics counters
4163 * @adapter: board private structure
4165 static void e1000e_update_stats(struct e1000_adapter *adapter)
4167 struct net_device *netdev = adapter->netdev;
4168 struct e1000_hw *hw = &adapter->hw;
4169 struct pci_dev *pdev = adapter->pdev;
4172 * Prevent stats update while adapter is being reset, or if the pci
4173 * connection is down.
4175 if (adapter->link_speed == 0)
4177 if (pci_channel_offline(pdev))
4180 adapter->stats.crcerrs += er32(CRCERRS);
4181 adapter->stats.gprc += er32(GPRC);
4182 adapter->stats.gorc += er32(GORCL);
4183 er32(GORCH); /* Clear gorc */
4184 adapter->stats.bprc += er32(BPRC);
4185 adapter->stats.mprc += er32(MPRC);
4186 adapter->stats.roc += er32(ROC);
4188 adapter->stats.mpc += er32(MPC);
4190 /* Half-duplex statistics */
4191 if (adapter->link_duplex == HALF_DUPLEX) {
4192 if (adapter->flags2 & FLAG2_HAS_PHY_STATS) {
4193 e1000e_update_phy_stats(adapter);
4195 adapter->stats.scc += er32(SCC);
4196 adapter->stats.ecol += er32(ECOL);
4197 adapter->stats.mcc += er32(MCC);
4198 adapter->stats.latecol += er32(LATECOL);
4199 adapter->stats.dc += er32(DC);
4201 hw->mac.collision_delta = er32(COLC);
4203 if ((hw->mac.type != e1000_82574) &&
4204 (hw->mac.type != e1000_82583))
4205 adapter->stats.tncrs += er32(TNCRS);
4207 adapter->stats.colc += hw->mac.collision_delta;
4210 adapter->stats.xonrxc += er32(XONRXC);
4211 adapter->stats.xontxc += er32(XONTXC);
4212 adapter->stats.xoffrxc += er32(XOFFRXC);
4213 adapter->stats.xofftxc += er32(XOFFTXC);
4214 adapter->stats.gptc += er32(GPTC);
4215 adapter->stats.gotc += er32(GOTCL);
4216 er32(GOTCH); /* Clear gotc */
4217 adapter->stats.rnbc += er32(RNBC);
4218 adapter->stats.ruc += er32(RUC);
4220 adapter->stats.mptc += er32(MPTC);
4221 adapter->stats.bptc += er32(BPTC);
4223 /* used for adaptive IFS */
4225 hw->mac.tx_packet_delta = er32(TPT);
4226 adapter->stats.tpt += hw->mac.tx_packet_delta;
4228 adapter->stats.algnerrc += er32(ALGNERRC);
4229 adapter->stats.rxerrc += er32(RXERRC);
4230 adapter->stats.cexterr += er32(CEXTERR);
4231 adapter->stats.tsctc += er32(TSCTC);
4232 adapter->stats.tsctfc += er32(TSCTFC);
4234 /* Fill out the OS statistics structure */
4235 netdev->stats.multicast = adapter->stats.mprc;
4236 netdev->stats.collisions = adapter->stats.colc;
4241 * RLEC on some newer hardware can be incorrect so build
4242 * our own version based on RUC and ROC
4244 netdev->stats.rx_errors = adapter->stats.rxerrc +
4245 adapter->stats.crcerrs + adapter->stats.algnerrc +
4246 adapter->stats.ruc + adapter->stats.roc +
4247 adapter->stats.cexterr;
4248 netdev->stats.rx_length_errors = adapter->stats.ruc +
4250 netdev->stats.rx_crc_errors = adapter->stats.crcerrs;
4251 netdev->stats.rx_frame_errors = adapter->stats.algnerrc;
4252 netdev->stats.rx_missed_errors = adapter->stats.mpc;
4255 netdev->stats.tx_errors = adapter->stats.ecol +
4256 adapter->stats.latecol;
4257 netdev->stats.tx_aborted_errors = adapter->stats.ecol;
4258 netdev->stats.tx_window_errors = adapter->stats.latecol;
4259 netdev->stats.tx_carrier_errors = adapter->stats.tncrs;
4261 /* Tx Dropped needs to be maintained elsewhere */
4263 /* Management Stats */
4264 adapter->stats.mgptc += er32(MGTPTC);
4265 adapter->stats.mgprc += er32(MGTPRC);
4266 adapter->stats.mgpdc += er32(MGTPDC);
4270 * e1000_phy_read_status - Update the PHY register status snapshot
4271 * @adapter: board private structure
4273 static void e1000_phy_read_status(struct e1000_adapter *adapter)
4275 struct e1000_hw *hw = &adapter->hw;
4276 struct e1000_phy_regs *phy = &adapter->phy_regs;
4278 if ((er32(STATUS) & E1000_STATUS_LU) &&
4279 (adapter->hw.phy.media_type == e1000_media_type_copper)) {
4282 ret_val = e1e_rphy(hw, PHY_CONTROL, &phy->bmcr);
4283 ret_val |= e1e_rphy(hw, PHY_STATUS, &phy->bmsr);
4284 ret_val |= e1e_rphy(hw, PHY_AUTONEG_ADV, &phy->advertise);
4285 ret_val |= e1e_rphy(hw, PHY_LP_ABILITY, &phy->lpa);
4286 ret_val |= e1e_rphy(hw, PHY_AUTONEG_EXP, &phy->expansion);
4287 ret_val |= e1e_rphy(hw, PHY_1000T_CTRL, &phy->ctrl1000);
4288 ret_val |= e1e_rphy(hw, PHY_1000T_STATUS, &phy->stat1000);
4289 ret_val |= e1e_rphy(hw, PHY_EXT_STATUS, &phy->estatus);
4291 e_warn("Error reading PHY register\n");
4294 * Do not read PHY registers if link is not up
4295 * Set values to typical power-on defaults
4297 phy->bmcr = (BMCR_SPEED1000 | BMCR_ANENABLE | BMCR_FULLDPLX);
4298 phy->bmsr = (BMSR_100FULL | BMSR_100HALF | BMSR_10FULL |
4299 BMSR_10HALF | BMSR_ESTATEN | BMSR_ANEGCAPABLE |
4301 phy->advertise = (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP |
4302 ADVERTISE_ALL | ADVERTISE_CSMA);
4304 phy->expansion = EXPANSION_ENABLENPAGE;
4305 phy->ctrl1000 = ADVERTISE_1000FULL;
4307 phy->estatus = (ESTATUS_1000_TFULL | ESTATUS_1000_THALF);
4311 static void e1000_print_link_info(struct e1000_adapter *adapter)
4313 struct e1000_hw *hw = &adapter->hw;
4314 u32 ctrl = er32(CTRL);
4316 /* Link status message must follow this format for user tools */
4317 printk(KERN_INFO "e1000e: %s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
4318 adapter->netdev->name,
4319 adapter->link_speed,
4320 adapter->link_duplex == FULL_DUPLEX ? "Full" : "Half",
4321 (ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE) ? "Rx/Tx" :
4322 (ctrl & E1000_CTRL_RFCE) ? "Rx" :
4323 (ctrl & E1000_CTRL_TFCE) ? "Tx" : "None");
4326 static bool e1000e_has_link(struct e1000_adapter *adapter)
4328 struct e1000_hw *hw = &adapter->hw;
4329 bool link_active = false;
4333 * get_link_status is set on LSC (link status) interrupt or
4334 * Rx sequence error interrupt. get_link_status will stay
4335 * false until the check_for_link establishes link
4336 * for copper adapters ONLY
4338 switch (hw->phy.media_type) {
4339 case e1000_media_type_copper:
4340 if (hw->mac.get_link_status) {
4341 ret_val = hw->mac.ops.check_for_link(hw);
4342 link_active = !hw->mac.get_link_status;
4347 case e1000_media_type_fiber:
4348 ret_val = hw->mac.ops.check_for_link(hw);
4349 link_active = !!(er32(STATUS) & E1000_STATUS_LU);
4351 case e1000_media_type_internal_serdes:
4352 ret_val = hw->mac.ops.check_for_link(hw);
4353 link_active = adapter->hw.mac.serdes_has_link;
4356 case e1000_media_type_unknown:
4360 if ((ret_val == E1000_ERR_PHY) && (hw->phy.type == e1000_phy_igp_3) &&
4361 (er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
4362 /* See e1000_kmrn_lock_loss_workaround_ich8lan() */
4363 e_info("Gigabit has been disabled, downgrading speed\n");
4369 static void e1000e_enable_receives(struct e1000_adapter *adapter)
4371 /* make sure the receive unit is started */
4372 if ((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
4373 (adapter->flags & FLAG_RX_RESTART_NOW)) {
4374 struct e1000_hw *hw = &adapter->hw;
4375 u32 rctl = er32(RCTL);
4376 ew32(RCTL, rctl | E1000_RCTL_EN);
4377 adapter->flags &= ~FLAG_RX_RESTART_NOW;
4381 static void e1000e_check_82574_phy_workaround(struct e1000_adapter *adapter)
4383 struct e1000_hw *hw = &adapter->hw;
4386 * With 82574 controllers, PHY needs to be checked periodically
4387 * for hung state and reset, if two calls return true
4389 if (e1000_check_phy_82574(hw))
4390 adapter->phy_hang_count++;
4392 adapter->phy_hang_count = 0;
4394 if (adapter->phy_hang_count > 1) {
4395 adapter->phy_hang_count = 0;
4396 schedule_work(&adapter->reset_task);
4401 * e1000_watchdog - Timer Call-back
4402 * @data: pointer to adapter cast into an unsigned long
4404 static void e1000_watchdog(unsigned long data)
4406 struct e1000_adapter *adapter = (struct e1000_adapter *) data;
4408 /* Do the rest outside of interrupt context */
4409 schedule_work(&adapter->watchdog_task);
4411 /* TODO: make this use queue_delayed_work() */
4414 static void e1000_watchdog_task(struct work_struct *work)
4416 struct e1000_adapter *adapter = container_of(work,
4417 struct e1000_adapter, watchdog_task);
4418 struct net_device *netdev = adapter->netdev;
4419 struct e1000_mac_info *mac = &adapter->hw.mac;
4420 struct e1000_phy_info *phy = &adapter->hw.phy;
4421 struct e1000_ring *tx_ring = adapter->tx_ring;
4422 struct e1000_hw *hw = &adapter->hw;
4425 if (test_bit(__E1000_DOWN, &adapter->state))
4428 link = e1000e_has_link(adapter);
4429 if ((netif_carrier_ok(netdev)) && link) {
4430 /* Cancel scheduled suspend requests. */
4431 pm_runtime_resume(netdev->dev.parent);
4433 e1000e_enable_receives(adapter);
4437 if ((e1000e_enable_tx_pkt_filtering(hw)) &&
4438 (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id))
4439 e1000_update_mng_vlan(adapter);
4442 if (!netif_carrier_ok(netdev)) {
4445 /* Cancel scheduled suspend requests. */
4446 pm_runtime_resume(netdev->dev.parent);
4448 /* update snapshot of PHY registers on LSC */
4449 e1000_phy_read_status(adapter);
4450 mac->ops.get_link_up_info(&adapter->hw,
4451 &adapter->link_speed,
4452 &adapter->link_duplex);
4453 e1000_print_link_info(adapter);
4455 * On supported PHYs, check for duplex mismatch only
4456 * if link has autonegotiated at 10/100 half
4458 if ((hw->phy.type == e1000_phy_igp_3 ||
4459 hw->phy.type == e1000_phy_bm) &&
4460 (hw->mac.autoneg == true) &&
4461 (adapter->link_speed == SPEED_10 ||
4462 adapter->link_speed == SPEED_100) &&
4463 (adapter->link_duplex == HALF_DUPLEX)) {
4466 e1e_rphy(hw, PHY_AUTONEG_EXP, &autoneg_exp);
4468 if (!(autoneg_exp & NWAY_ER_LP_NWAY_CAPS))
4469 e_info("Autonegotiated half duplex but link partner cannot autoneg. Try forcing full duplex if link gets many collisions.\n");
4472 /* adjust timeout factor according to speed/duplex */
4473 adapter->tx_timeout_factor = 1;
4474 switch (adapter->link_speed) {
4477 adapter->tx_timeout_factor = 16;
4481 adapter->tx_timeout_factor = 10;
4486 * workaround: re-program speed mode bit after
4489 if ((adapter->flags & FLAG_TARC_SPEED_MODE_BIT) &&
4492 tarc0 = er32(TARC(0));
4493 tarc0 &= ~SPEED_MODE_BIT;
4494 ew32(TARC(0), tarc0);
4498 * disable TSO for pcie and 10/100 speeds, to avoid
4499 * some hardware issues
4501 if (!(adapter->flags & FLAG_TSO_FORCE)) {
4502 switch (adapter->link_speed) {
4505 e_info("10/100 speed: disabling TSO\n");
4506 netdev->features &= ~NETIF_F_TSO;
4507 netdev->features &= ~NETIF_F_TSO6;
4510 netdev->features |= NETIF_F_TSO;
4511 netdev->features |= NETIF_F_TSO6;
4520 * enable transmits in the hardware, need to do this
4521 * after setting TARC(0)
4524 tctl |= E1000_TCTL_EN;
4528 * Perform any post-link-up configuration before
4529 * reporting link up.
4531 if (phy->ops.cfg_on_link_up)
4532 phy->ops.cfg_on_link_up(hw);
4534 netif_carrier_on(netdev);
4536 if (!test_bit(__E1000_DOWN, &adapter->state))
4537 mod_timer(&adapter->phy_info_timer,
4538 round_jiffies(jiffies + 2 * HZ));
4541 if (netif_carrier_ok(netdev)) {
4542 adapter->link_speed = 0;
4543 adapter->link_duplex = 0;
4544 /* Link status message must follow this format */
4545 printk(KERN_INFO "e1000e: %s NIC Link is Down\n",
4546 adapter->netdev->name);
4547 netif_carrier_off(netdev);
4548 if (!test_bit(__E1000_DOWN, &adapter->state))
4549 mod_timer(&adapter->phy_info_timer,
4550 round_jiffies(jiffies + 2 * HZ));
4552 if (adapter->flags & FLAG_RX_NEEDS_RESTART)
4553 schedule_work(&adapter->reset_task);
4555 pm_schedule_suspend(netdev->dev.parent,
4561 spin_lock(&adapter->stats64_lock);
4562 e1000e_update_stats(adapter);
4564 mac->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
4565 adapter->tpt_old = adapter->stats.tpt;
4566 mac->collision_delta = adapter->stats.colc - adapter->colc_old;
4567 adapter->colc_old = adapter->stats.colc;
4569 adapter->gorc = adapter->stats.gorc - adapter->gorc_old;
4570 adapter->gorc_old = adapter->stats.gorc;
4571 adapter->gotc = adapter->stats.gotc - adapter->gotc_old;
4572 adapter->gotc_old = adapter->stats.gotc;
4573 spin_unlock(&adapter->stats64_lock);
4575 e1000e_update_adaptive(&adapter->hw);
4577 if (!netif_carrier_ok(netdev) &&
4578 (e1000_desc_unused(tx_ring) + 1 < tx_ring->count)) {
4580 * We've lost link, so the controller stops DMA,
4581 * but we've got queued Tx work that's never going
4582 * to get done, so reset controller to flush Tx.
4583 * (Do the reset outside of interrupt context).
4585 schedule_work(&adapter->reset_task);
4586 /* return immediately since reset is imminent */
4590 /* Simple mode for Interrupt Throttle Rate (ITR) */
4591 if (adapter->itr_setting == 4) {
4593 * Symmetric Tx/Rx gets a reduced ITR=2000;
4594 * Total asymmetrical Tx or Rx gets ITR=8000;
4595 * everyone else is between 2000-8000.
4597 u32 goc = (adapter->gotc + adapter->gorc) / 10000;
4598 u32 dif = (adapter->gotc > adapter->gorc ?
4599 adapter->gotc - adapter->gorc :
4600 adapter->gorc - adapter->gotc) / 10000;
4601 u32 itr = goc > 0 ? (dif * 6000 / goc + 2000) : 8000;
4603 e1000e_write_itr(adapter, itr);
4606 /* Cause software interrupt to ensure Rx ring is cleaned */
4607 if (adapter->msix_entries)
4608 ew32(ICS, adapter->rx_ring->ims_val);
4610 ew32(ICS, E1000_ICS_RXDMT0);
4612 /* flush pending descriptors to memory before detecting Tx hang */
4613 e1000e_flush_descriptors(adapter);
4615 /* Force detection of hung controller every watchdog period */
4616 adapter->detect_tx_hung = true;
4619 * With 82571 controllers, LAA may be overwritten due to controller
4620 * reset from the other port. Set the appropriate LAA in RAR[0]
4622 if (e1000e_get_laa_state_82571(hw))
4623 hw->mac.ops.rar_set(hw, adapter->hw.mac.addr, 0);
4625 if (adapter->flags2 & FLAG2_CHECK_PHY_HANG)
4626 e1000e_check_82574_phy_workaround(adapter);
4628 /* Reset the timer */
4629 if (!test_bit(__E1000_DOWN, &adapter->state))
4630 mod_timer(&adapter->watchdog_timer,
4631 round_jiffies(jiffies + 2 * HZ));
4634 #define E1000_TX_FLAGS_CSUM 0x00000001
4635 #define E1000_TX_FLAGS_VLAN 0x00000002
4636 #define E1000_TX_FLAGS_TSO 0x00000004
4637 #define E1000_TX_FLAGS_IPV4 0x00000008
4638 #define E1000_TX_FLAGS_NO_FCS 0x00000010
4639 #define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
4640 #define E1000_TX_FLAGS_VLAN_SHIFT 16
4642 static int e1000_tso(struct e1000_ring *tx_ring, struct sk_buff *skb)
4644 struct e1000_context_desc *context_desc;
4645 struct e1000_buffer *buffer_info;
4648 u16 ipcse = 0, tucse, mss;
4649 u8 ipcss, ipcso, tucss, tucso, hdr_len;
4651 if (!skb_is_gso(skb))
4654 if (skb_header_cloned(skb)) {
4655 int err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
4661 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
4662 mss = skb_shinfo(skb)->gso_size;
4663 if (skb->protocol == htons(ETH_P_IP)) {
4664 struct iphdr *iph = ip_hdr(skb);
4667 tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr, iph->daddr,
4669 cmd_length = E1000_TXD_CMD_IP;
4670 ipcse = skb_transport_offset(skb) - 1;
4671 } else if (skb_is_gso_v6(skb)) {
4672 ipv6_hdr(skb)->payload_len = 0;
4673 tcp_hdr(skb)->check = ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
4674 &ipv6_hdr(skb)->daddr,
4678 ipcss = skb_network_offset(skb);
4679 ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data;
4680 tucss = skb_transport_offset(skb);
4681 tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data;
4684 cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE |
4685 E1000_TXD_CMD_TCP | (skb->len - (hdr_len)));
4687 i = tx_ring->next_to_use;
4688 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
4689 buffer_info = &tx_ring->buffer_info[i];
4691 context_desc->lower_setup.ip_fields.ipcss = ipcss;
4692 context_desc->lower_setup.ip_fields.ipcso = ipcso;
4693 context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
4694 context_desc->upper_setup.tcp_fields.tucss = tucss;
4695 context_desc->upper_setup.tcp_fields.tucso = tucso;
4696 context_desc->upper_setup.tcp_fields.tucse = cpu_to_le16(tucse);
4697 context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
4698 context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
4699 context_desc->cmd_and_length = cpu_to_le32(cmd_length);
4701 buffer_info->time_stamp = jiffies;
4702 buffer_info->next_to_watch = i;
4705 if (i == tx_ring->count)
4707 tx_ring->next_to_use = i;
4712 static bool e1000_tx_csum(struct e1000_ring *tx_ring, struct sk_buff *skb)
4714 struct e1000_adapter *adapter = tx_ring->adapter;
4715 struct e1000_context_desc *context_desc;
4716 struct e1000_buffer *buffer_info;
4719 u32 cmd_len = E1000_TXD_CMD_DEXT;
4722 if (skb->ip_summed != CHECKSUM_PARTIAL)
4725 if (skb->protocol == cpu_to_be16(ETH_P_8021Q))
4726 protocol = vlan_eth_hdr(skb)->h_vlan_encapsulated_proto;
4728 protocol = skb->protocol;
4731 case cpu_to_be16(ETH_P_IP):
4732 if (ip_hdr(skb)->protocol == IPPROTO_TCP)
4733 cmd_len |= E1000_TXD_CMD_TCP;
4735 case cpu_to_be16(ETH_P_IPV6):
4736 /* XXX not handling all IPV6 headers */
4737 if (ipv6_hdr(skb)->nexthdr == IPPROTO_TCP)
4738 cmd_len |= E1000_TXD_CMD_TCP;
4741 if (unlikely(net_ratelimit()))
4742 e_warn("checksum_partial proto=%x!\n",
4743 be16_to_cpu(protocol));
4747 css = skb_checksum_start_offset(skb);
4749 i = tx_ring->next_to_use;
4750 buffer_info = &tx_ring->buffer_info[i];
4751 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
4753 context_desc->lower_setup.ip_config = 0;
4754 context_desc->upper_setup.tcp_fields.tucss = css;
4755 context_desc->upper_setup.tcp_fields.tucso =
4756 css + skb->csum_offset;
4757 context_desc->upper_setup.tcp_fields.tucse = 0;
4758 context_desc->tcp_seg_setup.data = 0;
4759 context_desc->cmd_and_length = cpu_to_le32(cmd_len);
4761 buffer_info->time_stamp = jiffies;
4762 buffer_info->next_to_watch = i;
4765 if (i == tx_ring->count)
4767 tx_ring->next_to_use = i;
4772 #define E1000_MAX_PER_TXD 8192
4773 #define E1000_MAX_TXD_PWR 12
4775 static int e1000_tx_map(struct e1000_ring *tx_ring, struct sk_buff *skb,
4776 unsigned int first, unsigned int max_per_txd,
4777 unsigned int nr_frags, unsigned int mss)
4779 struct e1000_adapter *adapter = tx_ring->adapter;
4780 struct pci_dev *pdev = adapter->pdev;
4781 struct e1000_buffer *buffer_info;
4782 unsigned int len = skb_headlen(skb);
4783 unsigned int offset = 0, size, count = 0, i;
4784 unsigned int f, bytecount, segs;
4786 i = tx_ring->next_to_use;
4789 buffer_info = &tx_ring->buffer_info[i];
4790 size = min(len, max_per_txd);
4792 buffer_info->length = size;
4793 buffer_info->time_stamp = jiffies;
4794 buffer_info->next_to_watch = i;
4795 buffer_info->dma = dma_map_single(&pdev->dev,
4797 size, DMA_TO_DEVICE);
4798 buffer_info->mapped_as_page = false;
4799 if (dma_mapping_error(&pdev->dev, buffer_info->dma))
4808 if (i == tx_ring->count)
4813 for (f = 0; f < nr_frags; f++) {
4814 const struct skb_frag_struct *frag;
4816 frag = &skb_shinfo(skb)->frags[f];
4817 len = skb_frag_size(frag);
4822 if (i == tx_ring->count)
4825 buffer_info = &tx_ring->buffer_info[i];
4826 size = min(len, max_per_txd);
4828 buffer_info->length = size;
4829 buffer_info->time_stamp = jiffies;
4830 buffer_info->next_to_watch = i;
4831 buffer_info->dma = skb_frag_dma_map(&pdev->dev, frag,
4832 offset, size, DMA_TO_DEVICE);
4833 buffer_info->mapped_as_page = true;
4834 if (dma_mapping_error(&pdev->dev, buffer_info->dma))
4843 segs = skb_shinfo(skb)->gso_segs ? : 1;
4844 /* multiply data chunks by size of headers */
4845 bytecount = ((segs - 1) * skb_headlen(skb)) + skb->len;
4847 tx_ring->buffer_info[i].skb = skb;
4848 tx_ring->buffer_info[i].segs = segs;
4849 tx_ring->buffer_info[i].bytecount = bytecount;
4850 tx_ring->buffer_info[first].next_to_watch = i;
4855 dev_err(&pdev->dev, "Tx DMA map failed\n");
4856 buffer_info->dma = 0;
4862 i += tx_ring->count;
4864 buffer_info = &tx_ring->buffer_info[i];
4865 e1000_put_txbuf(tx_ring, buffer_info);
4871 static void e1000_tx_queue(struct e1000_ring *tx_ring, int tx_flags, int count)
4873 struct e1000_adapter *adapter = tx_ring->adapter;
4874 struct e1000_tx_desc *tx_desc = NULL;
4875 struct e1000_buffer *buffer_info;
4876 u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS;
4879 if (tx_flags & E1000_TX_FLAGS_TSO) {
4880 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
4882 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
4884 if (tx_flags & E1000_TX_FLAGS_IPV4)
4885 txd_upper |= E1000_TXD_POPTS_IXSM << 8;
4888 if (tx_flags & E1000_TX_FLAGS_CSUM) {
4889 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
4890 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
4893 if (tx_flags & E1000_TX_FLAGS_VLAN) {
4894 txd_lower |= E1000_TXD_CMD_VLE;
4895 txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK);
4898 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS))
4899 txd_lower &= ~(E1000_TXD_CMD_IFCS);
4901 i = tx_ring->next_to_use;
4904 buffer_info = &tx_ring->buffer_info[i];
4905 tx_desc = E1000_TX_DESC(*tx_ring, i);
4906 tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
4907 tx_desc->lower.data =
4908 cpu_to_le32(txd_lower | buffer_info->length);
4909 tx_desc->upper.data = cpu_to_le32(txd_upper);
4912 if (i == tx_ring->count)
4914 } while (--count > 0);
4916 tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd);
4918 /* txd_cmd re-enables FCS, so we'll re-disable it here as desired. */
4919 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS))
4920 tx_desc->lower.data &= ~(cpu_to_le32(E1000_TXD_CMD_IFCS));
4923 * Force memory writes to complete before letting h/w
4924 * know there are new descriptors to fetch. (Only
4925 * applicable for weak-ordered memory model archs,
4930 tx_ring->next_to_use = i;
4932 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
4933 e1000e_update_tdt_wa(tx_ring, i);
4935 writel(i, tx_ring->tail);
4938 * we need this if more than one processor can write to our tail
4939 * at a time, it synchronizes IO on IA64/Altix systems
4944 #define MINIMUM_DHCP_PACKET_SIZE 282
4945 static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
4946 struct sk_buff *skb)
4948 struct e1000_hw *hw = &adapter->hw;
4951 if (vlan_tx_tag_present(skb)) {
4952 if (!((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
4953 (adapter->hw.mng_cookie.status &
4954 E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
4958 if (skb->len <= MINIMUM_DHCP_PACKET_SIZE)
4961 if (((struct ethhdr *) skb->data)->h_proto != htons(ETH_P_IP))
4965 const struct iphdr *ip = (struct iphdr *)((u8 *)skb->data+14);
4968 if (ip->protocol != IPPROTO_UDP)
4971 udp = (struct udphdr *)((u8 *)ip + (ip->ihl << 2));
4972 if (ntohs(udp->dest) != 67)
4975 offset = (u8 *)udp + 8 - skb->data;
4976 length = skb->len - offset;
4977 return e1000e_mng_write_dhcp_info(hw, (u8 *)udp + 8, length);
4983 static int __e1000_maybe_stop_tx(struct e1000_ring *tx_ring, int size)
4985 struct e1000_adapter *adapter = tx_ring->adapter;
4987 netif_stop_queue(adapter->netdev);
4989 * Herbert's original patch had:
4990 * smp_mb__after_netif_stop_queue();
4991 * but since that doesn't exist yet, just open code it.
4996 * We need to check again in a case another CPU has just
4997 * made room available.
4999 if (e1000_desc_unused(tx_ring) < size)
5003 netif_start_queue(adapter->netdev);
5004 ++adapter->restart_queue;
5008 static int e1000_maybe_stop_tx(struct e1000_ring *tx_ring, int size)
5010 if (e1000_desc_unused(tx_ring) >= size)
5012 return __e1000_maybe_stop_tx(tx_ring, size);
5015 #define TXD_USE_COUNT(S, X) (((S) >> (X)) + 1)
5016 static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
5017 struct net_device *netdev)
5019 struct e1000_adapter *adapter = netdev_priv(netdev);
5020 struct e1000_ring *tx_ring = adapter->tx_ring;
5022 unsigned int max_per_txd = E1000_MAX_PER_TXD;
5023 unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
5024 unsigned int tx_flags = 0;
5025 unsigned int len = skb_headlen(skb);
5026 unsigned int nr_frags;
5032 if (test_bit(__E1000_DOWN, &adapter->state)) {
5033 dev_kfree_skb_any(skb);
5034 return NETDEV_TX_OK;
5037 if (skb->len <= 0) {
5038 dev_kfree_skb_any(skb);
5039 return NETDEV_TX_OK;
5042 mss = skb_shinfo(skb)->gso_size;
5044 * The controller does a simple calculation to
5045 * make sure there is enough room in the FIFO before
5046 * initiating the DMA for each buffer. The calc is:
5047 * 4 = ceil(buffer len/mss). To make sure we don't
5048 * overrun the FIFO, adjust the max buffer len if mss
5053 max_per_txd = min(mss << 2, max_per_txd);
5054 max_txd_pwr = fls(max_per_txd) - 1;
5057 * TSO Workaround for 82571/2/3 Controllers -- if skb->data
5058 * points to just header, pull a few bytes of payload from
5059 * frags into skb->data
5061 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
5063 * we do this workaround for ES2LAN, but it is un-necessary,
5064 * avoiding it could save a lot of cycles
5066 if (skb->data_len && (hdr_len == len)) {
5067 unsigned int pull_size;
5069 pull_size = min_t(unsigned int, 4, skb->data_len);
5070 if (!__pskb_pull_tail(skb, pull_size)) {
5071 e_err("__pskb_pull_tail failed.\n");
5072 dev_kfree_skb_any(skb);
5073 return NETDEV_TX_OK;
5075 len = skb_headlen(skb);
5079 /* reserve a descriptor for the offload context */
5080 if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
5084 count += TXD_USE_COUNT(len, max_txd_pwr);
5086 nr_frags = skb_shinfo(skb)->nr_frags;
5087 for (f = 0; f < nr_frags; f++)
5088 count += TXD_USE_COUNT(skb_frag_size(&skb_shinfo(skb)->frags[f]),
5091 if (adapter->hw.mac.tx_pkt_filtering)
5092 e1000_transfer_dhcp_info(adapter, skb);
5095 * need: count + 2 desc gap to keep tail from touching
5096 * head, otherwise try next time
5098 if (e1000_maybe_stop_tx(tx_ring, count + 2))
5099 return NETDEV_TX_BUSY;
5101 if (vlan_tx_tag_present(skb)) {
5102 tx_flags |= E1000_TX_FLAGS_VLAN;
5103 tx_flags |= (vlan_tx_tag_get(skb) << E1000_TX_FLAGS_VLAN_SHIFT);
5106 first = tx_ring->next_to_use;
5108 tso = e1000_tso(tx_ring, skb);
5110 dev_kfree_skb_any(skb);
5111 return NETDEV_TX_OK;
5115 tx_flags |= E1000_TX_FLAGS_TSO;
5116 else if (e1000_tx_csum(tx_ring, skb))
5117 tx_flags |= E1000_TX_FLAGS_CSUM;
5120 * Old method was to assume IPv4 packet by default if TSO was enabled.
5121 * 82571 hardware supports TSO capabilities for IPv6 as well...
5122 * no longer assume, we must.
5124 if (skb->protocol == htons(ETH_P_IP))
5125 tx_flags |= E1000_TX_FLAGS_IPV4;
5127 if (unlikely(skb->no_fcs))
5128 tx_flags |= E1000_TX_FLAGS_NO_FCS;
5130 /* if count is 0 then mapping error has occurred */
5131 count = e1000_tx_map(tx_ring, skb, first, max_per_txd, nr_frags, mss);
5133 skb_tx_timestamp(skb);
5135 netdev_sent_queue(netdev, skb->len);
5136 e1000_tx_queue(tx_ring, tx_flags, count);
5137 /* Make sure there is space in the ring for the next send. */
5138 e1000_maybe_stop_tx(tx_ring, MAX_SKB_FRAGS + 2);
5141 dev_kfree_skb_any(skb);
5142 tx_ring->buffer_info[first].time_stamp = 0;
5143 tx_ring->next_to_use = first;
5146 return NETDEV_TX_OK;
5150 * e1000_tx_timeout - Respond to a Tx Hang
5151 * @netdev: network interface device structure
5153 static void e1000_tx_timeout(struct net_device *netdev)
5155 struct e1000_adapter *adapter = netdev_priv(netdev);
5157 /* Do the reset outside of interrupt context */
5158 adapter->tx_timeout_count++;
5159 schedule_work(&adapter->reset_task);
5162 static void e1000_reset_task(struct work_struct *work)
5164 struct e1000_adapter *adapter;
5165 adapter = container_of(work, struct e1000_adapter, reset_task);
5167 /* don't run the task if already down */
5168 if (test_bit(__E1000_DOWN, &adapter->state))
5171 if (!((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
5172 (adapter->flags & FLAG_RX_RESTART_NOW))) {
5173 e1000e_dump(adapter);
5174 e_err("Reset adapter\n");
5176 e1000e_reinit_locked(adapter);
5180 * e1000_get_stats64 - Get System Network Statistics
5181 * @netdev: network interface device structure
5182 * @stats: rtnl_link_stats64 pointer
5184 * Returns the address of the device statistics structure.
5186 struct rtnl_link_stats64 *e1000e_get_stats64(struct net_device *netdev,
5187 struct rtnl_link_stats64 *stats)
5189 struct e1000_adapter *adapter = netdev_priv(netdev);
5191 memset(stats, 0, sizeof(struct rtnl_link_stats64));
5192 spin_lock(&adapter->stats64_lock);
5193 e1000e_update_stats(adapter);
5194 /* Fill out the OS statistics structure */
5195 stats->rx_bytes = adapter->stats.gorc;
5196 stats->rx_packets = adapter->stats.gprc;
5197 stats->tx_bytes = adapter->stats.gotc;
5198 stats->tx_packets = adapter->stats.gptc;
5199 stats->multicast = adapter->stats.mprc;
5200 stats->collisions = adapter->stats.colc;
5205 * RLEC on some newer hardware can be incorrect so build
5206 * our own version based on RUC and ROC
5208 stats->rx_errors = adapter->stats.rxerrc +
5209 adapter->stats.crcerrs + adapter->stats.algnerrc +
5210 adapter->stats.ruc + adapter->stats.roc +
5211 adapter->stats.cexterr;
5212 stats->rx_length_errors = adapter->stats.ruc +
5214 stats->rx_crc_errors = adapter->stats.crcerrs;
5215 stats->rx_frame_errors = adapter->stats.algnerrc;
5216 stats->rx_missed_errors = adapter->stats.mpc;
5219 stats->tx_errors = adapter->stats.ecol +
5220 adapter->stats.latecol;
5221 stats->tx_aborted_errors = adapter->stats.ecol;
5222 stats->tx_window_errors = adapter->stats.latecol;
5223 stats->tx_carrier_errors = adapter->stats.tncrs;
5225 /* Tx Dropped needs to be maintained elsewhere */
5227 spin_unlock(&adapter->stats64_lock);
5232 * e1000_change_mtu - Change the Maximum Transfer Unit
5233 * @netdev: network interface device structure
5234 * @new_mtu: new value for maximum frame size
5236 * Returns 0 on success, negative on failure
5238 static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
5240 struct e1000_adapter *adapter = netdev_priv(netdev);
5241 int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
5243 /* Jumbo frame support */
5244 if ((max_frame > ETH_FRAME_LEN + ETH_FCS_LEN) &&
5245 !(adapter->flags & FLAG_HAS_JUMBO_FRAMES)) {
5246 e_err("Jumbo Frames not supported.\n");
5250 /* Supported frame sizes */
5251 if ((new_mtu < ETH_ZLEN + ETH_FCS_LEN + VLAN_HLEN) ||
5252 (max_frame > adapter->max_hw_frame_size)) {
5253 e_err("Unsupported MTU setting\n");
5257 /* Jumbo frame workaround on 82579 and newer requires CRC be stripped */
5258 if ((adapter->hw.mac.type >= e1000_pch2lan) &&
5259 !(adapter->flags2 & FLAG2_CRC_STRIPPING) &&
5260 (new_mtu > ETH_DATA_LEN)) {
5261 e_err("Jumbo Frames not supported on this device when CRC stripping is disabled.\n");
5265 while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
5266 usleep_range(1000, 2000);
5267 /* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */
5268 adapter->max_frame_size = max_frame;
5269 e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
5270 netdev->mtu = new_mtu;
5271 if (netif_running(netdev))
5272 e1000e_down(adapter);
5275 * NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
5276 * means we reserve 2 more, this pushes us to allocate from the next
5278 * i.e. RXBUFFER_2048 --> size-4096 slab
5279 * However with the new *_jumbo_rx* routines, jumbo receives will use
5283 if (max_frame <= 2048)
5284 adapter->rx_buffer_len = 2048;
5286 adapter->rx_buffer_len = 4096;
5288 /* adjust allocation if LPE protects us, and we aren't using SBP */
5289 if ((max_frame == ETH_FRAME_LEN + ETH_FCS_LEN) ||
5290 (max_frame == ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN))
5291 adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN
5294 if (netif_running(netdev))
5297 e1000e_reset(adapter);
5299 clear_bit(__E1000_RESETTING, &adapter->state);
5304 static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
5307 struct e1000_adapter *adapter = netdev_priv(netdev);
5308 struct mii_ioctl_data *data = if_mii(ifr);
5310 if (adapter->hw.phy.media_type != e1000_media_type_copper)
5315 data->phy_id = adapter->hw.phy.addr;
5318 e1000_phy_read_status(adapter);
5320 switch (data->reg_num & 0x1F) {
5322 data->val_out = adapter->phy_regs.bmcr;
5325 data->val_out = adapter->phy_regs.bmsr;
5328 data->val_out = (adapter->hw.phy.id >> 16);
5331 data->val_out = (adapter->hw.phy.id & 0xFFFF);
5334 data->val_out = adapter->phy_regs.advertise;
5337 data->val_out = adapter->phy_regs.lpa;
5340 data->val_out = adapter->phy_regs.expansion;
5343 data->val_out = adapter->phy_regs.ctrl1000;
5346 data->val_out = adapter->phy_regs.stat1000;
5349 data->val_out = adapter->phy_regs.estatus;
5362 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
5368 return e1000_mii_ioctl(netdev, ifr, cmd);
5374 static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
5376 struct e1000_hw *hw = &adapter->hw;
5378 u16 phy_reg, wuc_enable;
5381 /* copy MAC RARs to PHY RARs */
5382 e1000_copy_rx_addrs_to_phy_ich8lan(hw);
5384 retval = hw->phy.ops.acquire(hw);
5386 e_err("Could not acquire PHY\n");
5390 /* Enable access to wakeup registers on and set page to BM_WUC_PAGE */
5391 retval = e1000_enable_phy_wakeup_reg_access_bm(hw, &wuc_enable);
5395 /* copy MAC MTA to PHY MTA - only needed for pchlan */
5396 for (i = 0; i < adapter->hw.mac.mta_reg_count; i++) {
5397 mac_reg = E1000_READ_REG_ARRAY(hw, E1000_MTA, i);
5398 hw->phy.ops.write_reg_page(hw, BM_MTA(i),
5399 (u16)(mac_reg & 0xFFFF));
5400 hw->phy.ops.write_reg_page(hw, BM_MTA(i) + 1,
5401 (u16)((mac_reg >> 16) & 0xFFFF));
5404 /* configure PHY Rx Control register */
5405 hw->phy.ops.read_reg_page(&adapter->hw, BM_RCTL, &phy_reg);
5406 mac_reg = er32(RCTL);
5407 if (mac_reg & E1000_RCTL_UPE)
5408 phy_reg |= BM_RCTL_UPE;
5409 if (mac_reg & E1000_RCTL_MPE)
5410 phy_reg |= BM_RCTL_MPE;
5411 phy_reg &= ~(BM_RCTL_MO_MASK);
5412 if (mac_reg & E1000_RCTL_MO_3)
5413 phy_reg |= (((mac_reg & E1000_RCTL_MO_3) >> E1000_RCTL_MO_SHIFT)
5414 << BM_RCTL_MO_SHIFT);
5415 if (mac_reg & E1000_RCTL_BAM)
5416 phy_reg |= BM_RCTL_BAM;
5417 if (mac_reg & E1000_RCTL_PMCF)
5418 phy_reg |= BM_RCTL_PMCF;
5419 mac_reg = er32(CTRL);
5420 if (mac_reg & E1000_CTRL_RFCE)
5421 phy_reg |= BM_RCTL_RFCE;
5422 hw->phy.ops.write_reg_page(&adapter->hw, BM_RCTL, phy_reg);
5424 /* enable PHY wakeup in MAC register */
5426 ew32(WUC, E1000_WUC_PHY_WAKE | E1000_WUC_PME_EN);
5428 /* configure and enable PHY wakeup in PHY registers */
5429 hw->phy.ops.write_reg_page(&adapter->hw, BM_WUFC, wufc);
5430 hw->phy.ops.write_reg_page(&adapter->hw, BM_WUC, E1000_WUC_PME_EN);
5432 /* activate PHY wakeup */
5433 wuc_enable |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT;
5434 retval = e1000_disable_phy_wakeup_reg_access_bm(hw, &wuc_enable);
5436 e_err("Could not set PHY Host Wakeup bit\n");
5438 hw->phy.ops.release(hw);
5443 static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake,
5446 struct net_device *netdev = pci_get_drvdata(pdev);
5447 struct e1000_adapter *adapter = netdev_priv(netdev);
5448 struct e1000_hw *hw = &adapter->hw;
5449 u32 ctrl, ctrl_ext, rctl, status;
5450 /* Runtime suspend should only enable wakeup for link changes */
5451 u32 wufc = runtime ? E1000_WUFC_LNKC : adapter->wol;
5454 netif_device_detach(netdev);
5456 if (netif_running(netdev)) {
5457 int count = E1000_CHECK_RESET_COUNT;
5459 while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
5460 usleep_range(10000, 20000);
5462 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
5463 e1000e_down(adapter);
5464 e1000_free_irq(adapter);
5466 e1000e_reset_interrupt_capability(adapter);
5468 retval = pci_save_state(pdev);
5472 status = er32(STATUS);
5473 if (status & E1000_STATUS_LU)
5474 wufc &= ~E1000_WUFC_LNKC;
5477 e1000_setup_rctl(adapter);
5478 e1000e_set_rx_mode(netdev);
5480 /* turn on all-multi mode if wake on multicast is enabled */
5481 if (wufc & E1000_WUFC_MC) {
5483 rctl |= E1000_RCTL_MPE;
5488 /* advertise wake from D3Cold */
5489 #define E1000_CTRL_ADVD3WUC 0x00100000
5490 /* phy power management enable */
5491 #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
5492 ctrl |= E1000_CTRL_ADVD3WUC;
5493 if (!(adapter->flags2 & FLAG2_HAS_PHY_WAKEUP))
5494 ctrl |= E1000_CTRL_EN_PHY_PWR_MGMT;
5497 if (adapter->hw.phy.media_type == e1000_media_type_fiber ||
5498 adapter->hw.phy.media_type ==
5499 e1000_media_type_internal_serdes) {
5500 /* keep the laser running in D3 */
5501 ctrl_ext = er32(CTRL_EXT);
5502 ctrl_ext |= E1000_CTRL_EXT_SDP3_DATA;
5503 ew32(CTRL_EXT, ctrl_ext);
5506 if (adapter->flags & FLAG_IS_ICH)
5507 e1000_suspend_workarounds_ich8lan(&adapter->hw);
5509 /* Allow time for pending master requests to run */
5510 e1000e_disable_pcie_master(&adapter->hw);
5512 if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) {
5513 /* enable wakeup by the PHY */
5514 retval = e1000_init_phy_wakeup(adapter, wufc);
5518 /* enable wakeup by the MAC */
5520 ew32(WUC, E1000_WUC_PME_EN);
5527 *enable_wake = !!wufc;
5529 /* make sure adapter isn't asleep if manageability is enabled */
5530 if ((adapter->flags & FLAG_MNG_PT_ENABLED) ||
5531 (hw->mac.ops.check_mng_mode(hw)))
5532 *enable_wake = true;
5534 if (adapter->hw.phy.type == e1000_phy_igp_3)
5535 e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw);
5538 * Release control of h/w to f/w. If f/w is AMT enabled, this
5539 * would have already happened in close and is redundant.
5541 e1000e_release_hw_control(adapter);
5543 pci_disable_device(pdev);
5548 static void e1000_power_off(struct pci_dev *pdev, bool sleep, bool wake)
5550 if (sleep && wake) {
5551 pci_prepare_to_sleep(pdev);
5555 pci_wake_from_d3(pdev, wake);
5556 pci_set_power_state(pdev, PCI_D3hot);
5559 static void e1000_complete_shutdown(struct pci_dev *pdev, bool sleep,
5562 struct net_device *netdev = pci_get_drvdata(pdev);
5563 struct e1000_adapter *adapter = netdev_priv(netdev);
5566 * The pci-e switch on some quad port adapters will report a
5567 * correctable error when the MAC transitions from D0 to D3. To
5568 * prevent this we need to mask off the correctable errors on the
5569 * downstream port of the pci-e switch.
5571 if (adapter->flags & FLAG_IS_QUAD_PORT) {
5572 struct pci_dev *us_dev = pdev->bus->self;
5573 int pos = pci_pcie_cap(us_dev);
5576 pci_read_config_word(us_dev, pos + PCI_EXP_DEVCTL, &devctl);
5577 pci_write_config_word(us_dev, pos + PCI_EXP_DEVCTL,
5578 (devctl & ~PCI_EXP_DEVCTL_CERE));
5580 e1000_power_off(pdev, sleep, wake);
5582 pci_write_config_word(us_dev, pos + PCI_EXP_DEVCTL, devctl);
5584 e1000_power_off(pdev, sleep, wake);
5588 #ifdef CONFIG_PCIEASPM
5589 static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
5591 pci_disable_link_state_locked(pdev, state);
5594 static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
5600 * Both device and parent should have the same ASPM setting.
5601 * Disable ASPM in downstream component first and then upstream.
5603 pos = pci_pcie_cap(pdev);
5604 pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, ®16);
5606 pci_write_config_word(pdev, pos + PCI_EXP_LNKCTL, reg16);
5608 if (!pdev->bus->self)
5611 pos = pci_pcie_cap(pdev->bus->self);
5612 pci_read_config_word(pdev->bus->self, pos + PCI_EXP_LNKCTL, ®16);
5614 pci_write_config_word(pdev->bus->self, pos + PCI_EXP_LNKCTL, reg16);
5617 static void e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
5619 dev_info(&pdev->dev, "Disabling ASPM %s %s\n",
5620 (state & PCIE_LINK_STATE_L0S) ? "L0s" : "",
5621 (state & PCIE_LINK_STATE_L1) ? "L1" : "");
5623 __e1000e_disable_aspm(pdev, state);
5627 static bool e1000e_pm_ready(struct e1000_adapter *adapter)
5629 return !!adapter->tx_ring->buffer_info;
5632 static int __e1000_resume(struct pci_dev *pdev)
5634 struct net_device *netdev = pci_get_drvdata(pdev);
5635 struct e1000_adapter *adapter = netdev_priv(netdev);
5636 struct e1000_hw *hw = &adapter->hw;
5637 u16 aspm_disable_flag = 0;
5640 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L0S)
5641 aspm_disable_flag = PCIE_LINK_STATE_L0S;
5642 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1)
5643 aspm_disable_flag |= PCIE_LINK_STATE_L1;
5644 if (aspm_disable_flag)
5645 e1000e_disable_aspm(pdev, aspm_disable_flag);
5647 pci_set_power_state(pdev, PCI_D0);
5648 pci_restore_state(pdev);
5649 pci_save_state(pdev);
5651 e1000e_set_interrupt_capability(adapter);
5652 if (netif_running(netdev)) {
5653 err = e1000_request_irq(adapter);
5658 if (hw->mac.type >= e1000_pch2lan)
5659 e1000_resume_workarounds_pchlan(&adapter->hw);
5661 e1000e_power_up_phy(adapter);
5663 /* report the system wakeup cause from S3/S4 */
5664 if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) {
5667 e1e_rphy(&adapter->hw, BM_WUS, &phy_data);
5669 e_info("PHY Wakeup cause - %s\n",
5670 phy_data & E1000_WUS_EX ? "Unicast Packet" :
5671 phy_data & E1000_WUS_MC ? "Multicast Packet" :
5672 phy_data & E1000_WUS_BC ? "Broadcast Packet" :
5673 phy_data & E1000_WUS_MAG ? "Magic Packet" :
5674 phy_data & E1000_WUS_LNKC ?
5675 "Link Status Change" : "other");
5677 e1e_wphy(&adapter->hw, BM_WUS, ~0);
5679 u32 wus = er32(WUS);
5681 e_info("MAC Wakeup cause - %s\n",
5682 wus & E1000_WUS_EX ? "Unicast Packet" :
5683 wus & E1000_WUS_MC ? "Multicast Packet" :
5684 wus & E1000_WUS_BC ? "Broadcast Packet" :
5685 wus & E1000_WUS_MAG ? "Magic Packet" :
5686 wus & E1000_WUS_LNKC ? "Link Status Change" :
5692 e1000e_reset(adapter);
5694 e1000_init_manageability_pt(adapter);
5696 if (netif_running(netdev))
5699 netif_device_attach(netdev);
5702 * If the controller has AMT, do not set DRV_LOAD until the interface
5703 * is up. For all other cases, let the f/w know that the h/w is now
5704 * under the control of the driver.
5706 if (!(adapter->flags & FLAG_HAS_AMT))
5707 e1000e_get_hw_control(adapter);
5712 #ifdef CONFIG_PM_SLEEP
5713 static int e1000_suspend(struct device *dev)
5715 struct pci_dev *pdev = to_pci_dev(dev);
5719 retval = __e1000_shutdown(pdev, &wake, false);
5721 e1000_complete_shutdown(pdev, true, wake);
5726 static int e1000_resume(struct device *dev)
5728 struct pci_dev *pdev = to_pci_dev(dev);
5729 struct net_device *netdev = pci_get_drvdata(pdev);
5730 struct e1000_adapter *adapter = netdev_priv(netdev);
5732 if (e1000e_pm_ready(adapter))
5733 adapter->idle_check = true;
5735 return __e1000_resume(pdev);
5737 #endif /* CONFIG_PM_SLEEP */
5739 #ifdef CONFIG_PM_RUNTIME
5740 static int e1000_runtime_suspend(struct device *dev)
5742 struct pci_dev *pdev = to_pci_dev(dev);
5743 struct net_device *netdev = pci_get_drvdata(pdev);
5744 struct e1000_adapter *adapter = netdev_priv(netdev);
5746 if (e1000e_pm_ready(adapter)) {
5749 __e1000_shutdown(pdev, &wake, true);
5755 static int e1000_idle(struct device *dev)
5757 struct pci_dev *pdev = to_pci_dev(dev);
5758 struct net_device *netdev = pci_get_drvdata(pdev);
5759 struct e1000_adapter *adapter = netdev_priv(netdev);
5761 if (!e1000e_pm_ready(adapter))
5764 if (adapter->idle_check) {
5765 adapter->idle_check = false;
5766 if (!e1000e_has_link(adapter))
5767 pm_schedule_suspend(dev, MSEC_PER_SEC);
5773 static int e1000_runtime_resume(struct device *dev)
5775 struct pci_dev *pdev = to_pci_dev(dev);
5776 struct net_device *netdev = pci_get_drvdata(pdev);
5777 struct e1000_adapter *adapter = netdev_priv(netdev);
5779 if (!e1000e_pm_ready(adapter))
5782 adapter->idle_check = !dev->power.runtime_auto;
5783 return __e1000_resume(pdev);
5785 #endif /* CONFIG_PM_RUNTIME */
5786 #endif /* CONFIG_PM */
5788 static void e1000_shutdown(struct pci_dev *pdev)
5792 __e1000_shutdown(pdev, &wake, false);
5794 if (system_state == SYSTEM_POWER_OFF)
5795 e1000_complete_shutdown(pdev, false, wake);
5798 #ifdef CONFIG_NET_POLL_CONTROLLER
5800 static irqreturn_t e1000_intr_msix(int irq, void *data)
5802 struct net_device *netdev = data;
5803 struct e1000_adapter *adapter = netdev_priv(netdev);
5805 if (adapter->msix_entries) {
5806 int vector, msix_irq;
5809 msix_irq = adapter->msix_entries[vector].vector;
5810 disable_irq(msix_irq);
5811 e1000_intr_msix_rx(msix_irq, netdev);
5812 enable_irq(msix_irq);
5815 msix_irq = adapter->msix_entries[vector].vector;
5816 disable_irq(msix_irq);
5817 e1000_intr_msix_tx(msix_irq, netdev);
5818 enable_irq(msix_irq);
5821 msix_irq = adapter->msix_entries[vector].vector;
5822 disable_irq(msix_irq);
5823 e1000_msix_other(msix_irq, netdev);
5824 enable_irq(msix_irq);
5831 * Polling 'interrupt' - used by things like netconsole to send skbs
5832 * without having to re-enable interrupts. It's not called while
5833 * the interrupt routine is executing.
5835 static void e1000_netpoll(struct net_device *netdev)
5837 struct e1000_adapter *adapter = netdev_priv(netdev);
5839 switch (adapter->int_mode) {
5840 case E1000E_INT_MODE_MSIX:
5841 e1000_intr_msix(adapter->pdev->irq, netdev);
5843 case E1000E_INT_MODE_MSI:
5844 disable_irq(adapter->pdev->irq);
5845 e1000_intr_msi(adapter->pdev->irq, netdev);
5846 enable_irq(adapter->pdev->irq);
5848 default: /* E1000E_INT_MODE_LEGACY */
5849 disable_irq(adapter->pdev->irq);
5850 e1000_intr(adapter->pdev->irq, netdev);
5851 enable_irq(adapter->pdev->irq);
5858 * e1000_io_error_detected - called when PCI error is detected
5859 * @pdev: Pointer to PCI device
5860 * @state: The current pci connection state
5862 * This function is called after a PCI bus error affecting
5863 * this device has been detected.
5865 static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
5866 pci_channel_state_t state)
5868 struct net_device *netdev = pci_get_drvdata(pdev);
5869 struct e1000_adapter *adapter = netdev_priv(netdev);
5871 netif_device_detach(netdev);
5873 if (state == pci_channel_io_perm_failure)
5874 return PCI_ERS_RESULT_DISCONNECT;
5876 if (netif_running(netdev))
5877 e1000e_down(adapter);
5878 pci_disable_device(pdev);
5880 /* Request a slot slot reset. */
5881 return PCI_ERS_RESULT_NEED_RESET;
5885 * e1000_io_slot_reset - called after the pci bus has been reset.
5886 * @pdev: Pointer to PCI device
5888 * Restart the card from scratch, as if from a cold-boot. Implementation
5889 * resembles the first-half of the e1000_resume routine.
5891 static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
5893 struct net_device *netdev = pci_get_drvdata(pdev);
5894 struct e1000_adapter *adapter = netdev_priv(netdev);
5895 struct e1000_hw *hw = &adapter->hw;
5896 u16 aspm_disable_flag = 0;
5898 pci_ers_result_t result;
5900 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L0S)
5901 aspm_disable_flag = PCIE_LINK_STATE_L0S;
5902 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1)
5903 aspm_disable_flag |= PCIE_LINK_STATE_L1;
5904 if (aspm_disable_flag)
5905 e1000e_disable_aspm(pdev, aspm_disable_flag);
5907 err = pci_enable_device_mem(pdev);
5910 "Cannot re-enable PCI device after reset.\n");
5911 result = PCI_ERS_RESULT_DISCONNECT;
5913 pci_set_master(pdev);
5914 pdev->state_saved = true;
5915 pci_restore_state(pdev);
5917 pci_enable_wake(pdev, PCI_D3hot, 0);
5918 pci_enable_wake(pdev, PCI_D3cold, 0);
5920 e1000e_reset(adapter);
5922 result = PCI_ERS_RESULT_RECOVERED;
5925 pci_cleanup_aer_uncorrect_error_status(pdev);
5931 * e1000_io_resume - called when traffic can start flowing again.
5932 * @pdev: Pointer to PCI device
5934 * This callback is called when the error recovery driver tells us that
5935 * its OK to resume normal operation. Implementation resembles the
5936 * second-half of the e1000_resume routine.
5938 static void e1000_io_resume(struct pci_dev *pdev)
5940 struct net_device *netdev = pci_get_drvdata(pdev);
5941 struct e1000_adapter *adapter = netdev_priv(netdev);
5943 e1000_init_manageability_pt(adapter);
5945 if (netif_running(netdev)) {
5946 if (e1000e_up(adapter)) {
5948 "can't bring device back up after reset\n");
5953 netif_device_attach(netdev);
5956 * If the controller has AMT, do not set DRV_LOAD until the interface
5957 * is up. For all other cases, let the f/w know that the h/w is now
5958 * under the control of the driver.
5960 if (!(adapter->flags & FLAG_HAS_AMT))
5961 e1000e_get_hw_control(adapter);
5965 static void e1000_print_device_info(struct e1000_adapter *adapter)
5967 struct e1000_hw *hw = &adapter->hw;
5968 struct net_device *netdev = adapter->netdev;
5970 u8 pba_str[E1000_PBANUM_LENGTH];
5972 /* print bus type/speed/width info */
5973 e_info("(PCI Express:2.5GT/s:%s) %pM\n",
5975 ((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" :
5979 e_info("Intel(R) PRO/%s Network Connection\n",
5980 (hw->phy.type == e1000_phy_ife) ? "10/100" : "1000");
5981 ret_val = e1000_read_pba_string_generic(hw, pba_str,
5982 E1000_PBANUM_LENGTH);
5984 strlcpy((char *)pba_str, "Unknown", sizeof(pba_str));
5985 e_info("MAC: %d, PHY: %d, PBA No: %s\n",
5986 hw->mac.type, hw->phy.type, pba_str);
5989 static void e1000_eeprom_checks(struct e1000_adapter *adapter)
5991 struct e1000_hw *hw = &adapter->hw;
5995 if (hw->mac.type != e1000_82573)
5998 ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &buf);
6000 if (!ret_val && (!(buf & (1 << 0)))) {
6001 /* Deep Smart Power Down (DSPD) */
6002 dev_warn(&adapter->pdev->dev,
6003 "Warning: detected DSPD enabled in EEPROM\n");
6007 static int e1000_set_features(struct net_device *netdev,
6008 netdev_features_t features)
6010 struct e1000_adapter *adapter = netdev_priv(netdev);
6011 netdev_features_t changed = features ^ netdev->features;
6013 if (changed & (NETIF_F_TSO | NETIF_F_TSO6))
6014 adapter->flags |= FLAG_TSO_FORCE;
6016 if (!(changed & (NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_TX |
6017 NETIF_F_RXCSUM | NETIF_F_RXHASH | NETIF_F_RXFCS |
6021 if (changed & NETIF_F_RXFCS) {
6022 if (features & NETIF_F_RXFCS) {
6023 adapter->flags2 &= ~FLAG2_CRC_STRIPPING;
6025 /* We need to take it back to defaults, which might mean
6026 * stripping is still disabled at the adapter level.
6028 if (adapter->flags2 & FLAG2_DFLT_CRC_STRIPPING)
6029 adapter->flags2 |= FLAG2_CRC_STRIPPING;
6031 adapter->flags2 &= ~FLAG2_CRC_STRIPPING;
6035 netdev->features = features;
6037 if (netif_running(netdev))
6038 e1000e_reinit_locked(adapter);
6040 e1000e_reset(adapter);
6045 static const struct net_device_ops e1000e_netdev_ops = {
6046 .ndo_open = e1000_open,
6047 .ndo_stop = e1000_close,
6048 .ndo_start_xmit = e1000_xmit_frame,
6049 .ndo_get_stats64 = e1000e_get_stats64,
6050 .ndo_set_rx_mode = e1000e_set_rx_mode,
6051 .ndo_set_mac_address = e1000_set_mac,
6052 .ndo_change_mtu = e1000_change_mtu,
6053 .ndo_do_ioctl = e1000_ioctl,
6054 .ndo_tx_timeout = e1000_tx_timeout,
6055 .ndo_validate_addr = eth_validate_addr,
6057 .ndo_vlan_rx_add_vid = e1000_vlan_rx_add_vid,
6058 .ndo_vlan_rx_kill_vid = e1000_vlan_rx_kill_vid,
6059 #ifdef CONFIG_NET_POLL_CONTROLLER
6060 .ndo_poll_controller = e1000_netpoll,
6062 .ndo_set_features = e1000_set_features,
6066 * e1000_probe - Device Initialization Routine
6067 * @pdev: PCI device information struct
6068 * @ent: entry in e1000_pci_tbl
6070 * Returns 0 on success, negative on failure
6072 * e1000_probe initializes an adapter identified by a pci_dev structure.
6073 * The OS initialization, configuring of the adapter private structure,
6074 * and a hardware reset occur.
6076 static int __devinit e1000_probe(struct pci_dev *pdev,
6077 const struct pci_device_id *ent)
6079 struct net_device *netdev;
6080 struct e1000_adapter *adapter;
6081 struct e1000_hw *hw;
6082 const struct e1000_info *ei = e1000_info_tbl[ent->driver_data];
6083 resource_size_t mmio_start, mmio_len;
6084 resource_size_t flash_start, flash_len;
6085 static int cards_found;
6086 u16 aspm_disable_flag = 0;
6087 int i, err, pci_using_dac;
6088 u16 eeprom_data = 0;
6089 u16 eeprom_apme_mask = E1000_EEPROM_APME;
6091 if (ei->flags2 & FLAG2_DISABLE_ASPM_L0S)
6092 aspm_disable_flag = PCIE_LINK_STATE_L0S;
6093 if (ei->flags2 & FLAG2_DISABLE_ASPM_L1)
6094 aspm_disable_flag |= PCIE_LINK_STATE_L1;
6095 if (aspm_disable_flag)
6096 e1000e_disable_aspm(pdev, aspm_disable_flag);
6098 err = pci_enable_device_mem(pdev);
6103 err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
6105 err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
6109 err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
6111 err = dma_set_coherent_mask(&pdev->dev,
6114 dev_err(&pdev->dev, "No usable DMA configuration, aborting\n");
6120 err = pci_request_selected_regions_exclusive(pdev,
6121 pci_select_bars(pdev, IORESOURCE_MEM),
6122 e1000e_driver_name);
6126 /* AER (Advanced Error Reporting) hooks */
6127 pci_enable_pcie_error_reporting(pdev);
6129 pci_set_master(pdev);
6130 /* PCI config space info */
6131 err = pci_save_state(pdev);
6133 goto err_alloc_etherdev;
6136 netdev = alloc_etherdev(sizeof(struct e1000_adapter));
6138 goto err_alloc_etherdev;
6140 SET_NETDEV_DEV(netdev, &pdev->dev);
6142 netdev->irq = pdev->irq;
6144 pci_set_drvdata(pdev, netdev);
6145 adapter = netdev_priv(netdev);
6147 adapter->netdev = netdev;
6148 adapter->pdev = pdev;
6150 adapter->pba = ei->pba;
6151 adapter->flags = ei->flags;
6152 adapter->flags2 = ei->flags2;
6153 adapter->hw.adapter = adapter;
6154 adapter->hw.mac.type = ei->mac;
6155 adapter->max_hw_frame_size = ei->max_hw_frame_size;
6156 adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE);
6158 mmio_start = pci_resource_start(pdev, 0);
6159 mmio_len = pci_resource_len(pdev, 0);
6162 adapter->hw.hw_addr = ioremap(mmio_start, mmio_len);
6163 if (!adapter->hw.hw_addr)
6166 if ((adapter->flags & FLAG_HAS_FLASH) &&
6167 (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
6168 flash_start = pci_resource_start(pdev, 1);
6169 flash_len = pci_resource_len(pdev, 1);
6170 adapter->hw.flash_address = ioremap(flash_start, flash_len);
6171 if (!adapter->hw.flash_address)
6175 /* construct the net_device struct */
6176 netdev->netdev_ops = &e1000e_netdev_ops;
6177 e1000e_set_ethtool_ops(netdev);
6178 netdev->watchdog_timeo = 5 * HZ;
6179 netif_napi_add(netdev, &adapter->napi, e1000e_poll, 64);
6180 strlcpy(netdev->name, pci_name(pdev), sizeof(netdev->name));
6182 netdev->mem_start = mmio_start;
6183 netdev->mem_end = mmio_start + mmio_len;
6185 adapter->bd_number = cards_found++;
6187 e1000e_check_options(adapter);
6189 /* setup adapter struct */
6190 err = e1000_sw_init(adapter);
6194 memcpy(&hw->mac.ops, ei->mac_ops, sizeof(hw->mac.ops));
6195 memcpy(&hw->nvm.ops, ei->nvm_ops, sizeof(hw->nvm.ops));
6196 memcpy(&hw->phy.ops, ei->phy_ops, sizeof(hw->phy.ops));
6198 err = ei->get_variants(adapter);
6202 if ((adapter->flags & FLAG_IS_ICH) &&
6203 (adapter->flags & FLAG_READ_ONLY_NVM))
6204 e1000e_write_protect_nvm_ich8lan(&adapter->hw);
6206 hw->mac.ops.get_bus_info(&adapter->hw);
6208 adapter->hw.phy.autoneg_wait_to_complete = 0;
6210 /* Copper options */
6211 if (adapter->hw.phy.media_type == e1000_media_type_copper) {
6212 adapter->hw.phy.mdix = AUTO_ALL_MODES;
6213 adapter->hw.phy.disable_polarity_correction = 0;
6214 adapter->hw.phy.ms_type = e1000_ms_hw_default;
6217 if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw))
6218 dev_info(&pdev->dev,
6219 "PHY reset is blocked due to SOL/IDER session.\n");
6221 /* Set initial default active device features */
6222 netdev->features = (NETIF_F_SG |
6223 NETIF_F_HW_VLAN_RX |
6224 NETIF_F_HW_VLAN_TX |
6231 /* Set user-changeable features (subset of all device features) */
6232 netdev->hw_features = netdev->features;
6233 netdev->hw_features |= NETIF_F_RXFCS;
6234 netdev->priv_flags |= IFF_SUPP_NOFCS;
6235 netdev->hw_features |= NETIF_F_RXALL;
6237 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER)
6238 netdev->features |= NETIF_F_HW_VLAN_FILTER;
6240 netdev->vlan_features |= (NETIF_F_SG |
6245 netdev->priv_flags |= IFF_UNICAST_FLT;
6247 if (pci_using_dac) {
6248 netdev->features |= NETIF_F_HIGHDMA;
6249 netdev->vlan_features |= NETIF_F_HIGHDMA;
6252 if (e1000e_enable_mng_pass_thru(&adapter->hw))
6253 adapter->flags |= FLAG_MNG_PT_ENABLED;
6256 * before reading the NVM, reset the controller to
6257 * put the device in a known good starting state
6259 adapter->hw.mac.ops.reset_hw(&adapter->hw);
6262 * systems with ASPM and others may see the checksum fail on the first
6263 * attempt. Let's give it a few tries
6266 if (e1000_validate_nvm_checksum(&adapter->hw) >= 0)
6269 dev_err(&pdev->dev, "The NVM Checksum Is Not Valid\n");
6275 e1000_eeprom_checks(adapter);
6277 /* copy the MAC address */
6278 if (e1000e_read_mac_addr(&adapter->hw))
6280 "NVM Read Error while reading MAC address\n");
6282 memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
6283 memcpy(netdev->perm_addr, adapter->hw.mac.addr, netdev->addr_len);
6285 if (!is_valid_ether_addr(netdev->perm_addr)) {
6286 dev_err(&pdev->dev, "Invalid MAC Address: %pM\n",
6292 init_timer(&adapter->watchdog_timer);
6293 adapter->watchdog_timer.function = e1000_watchdog;
6294 adapter->watchdog_timer.data = (unsigned long) adapter;
6296 init_timer(&adapter->phy_info_timer);
6297 adapter->phy_info_timer.function = e1000_update_phy_info;
6298 adapter->phy_info_timer.data = (unsigned long) adapter;
6300 INIT_WORK(&adapter->reset_task, e1000_reset_task);
6301 INIT_WORK(&adapter->watchdog_task, e1000_watchdog_task);
6302 INIT_WORK(&adapter->downshift_task, e1000e_downshift_workaround);
6303 INIT_WORK(&adapter->update_phy_task, e1000e_update_phy_task);
6304 INIT_WORK(&adapter->print_hang_task, e1000_print_hw_hang);
6306 /* Initialize link parameters. User can change them with ethtool */
6307 adapter->hw.mac.autoneg = 1;
6308 adapter->fc_autoneg = true;
6309 adapter->hw.fc.requested_mode = e1000_fc_default;
6310 adapter->hw.fc.current_mode = e1000_fc_default;
6311 adapter->hw.phy.autoneg_advertised = 0x2f;
6313 /* ring size defaults */
6314 adapter->rx_ring->count = 256;
6315 adapter->tx_ring->count = 256;
6318 * Initial Wake on LAN setting - If APM wake is enabled in
6319 * the EEPROM, enable the ACPI Magic Packet filter
6321 if (adapter->flags & FLAG_APME_IN_WUC) {
6322 /* APME bit in EEPROM is mapped to WUC.APME */
6323 eeprom_data = er32(WUC);
6324 eeprom_apme_mask = E1000_WUC_APME;
6325 if ((hw->mac.type > e1000_ich10lan) &&
6326 (eeprom_data & E1000_WUC_PHY_WAKE))
6327 adapter->flags2 |= FLAG2_HAS_PHY_WAKEUP;
6328 } else if (adapter->flags & FLAG_APME_IN_CTRL3) {
6329 if (adapter->flags & FLAG_APME_CHECK_PORT_B &&
6330 (adapter->hw.bus.func == 1))
6331 e1000_read_nvm(&adapter->hw, NVM_INIT_CONTROL3_PORT_B,
6334 e1000_read_nvm(&adapter->hw, NVM_INIT_CONTROL3_PORT_A,
6338 /* fetch WoL from EEPROM */
6339 if (eeprom_data & eeprom_apme_mask)
6340 adapter->eeprom_wol |= E1000_WUFC_MAG;
6343 * now that we have the eeprom settings, apply the special cases
6344 * where the eeprom may be wrong or the board simply won't support
6345 * wake on lan on a particular port
6347 if (!(adapter->flags & FLAG_HAS_WOL))
6348 adapter->eeprom_wol = 0;
6350 /* initialize the wol settings based on the eeprom settings */
6351 adapter->wol = adapter->eeprom_wol;
6352 device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
6354 /* save off EEPROM version number */
6355 e1000_read_nvm(&adapter->hw, 5, 1, &adapter->eeprom_vers);
6357 /* reset the hardware with the new settings */
6358 e1000e_reset(adapter);
6361 * If the controller has AMT, do not set DRV_LOAD until the interface
6362 * is up. For all other cases, let the f/w know that the h/w is now
6363 * under the control of the driver.
6365 if (!(adapter->flags & FLAG_HAS_AMT))
6366 e1000e_get_hw_control(adapter);
6368 strlcpy(netdev->name, "eth%d", sizeof(netdev->name));
6369 err = register_netdev(netdev);
6373 /* carrier off reporting is important to ethtool even BEFORE open */
6374 netif_carrier_off(netdev);
6376 e1000_print_device_info(adapter);
6378 if (pci_dev_run_wake(pdev))
6379 pm_runtime_put_noidle(&pdev->dev);
6384 if (!(adapter->flags & FLAG_HAS_AMT))
6385 e1000e_release_hw_control(adapter);
6387 if (hw->phy.ops.check_reset_block && !hw->phy.ops.check_reset_block(hw))
6388 e1000_phy_hw_reset(&adapter->hw);
6390 kfree(adapter->tx_ring);
6391 kfree(adapter->rx_ring);
6393 if (adapter->hw.flash_address)
6394 iounmap(adapter->hw.flash_address);
6395 e1000e_reset_interrupt_capability(adapter);
6397 iounmap(adapter->hw.hw_addr);
6399 free_netdev(netdev);
6401 pci_release_selected_regions(pdev,
6402 pci_select_bars(pdev, IORESOURCE_MEM));
6405 pci_disable_device(pdev);
6410 * e1000_remove - Device Removal Routine
6411 * @pdev: PCI device information struct
6413 * e1000_remove is called by the PCI subsystem to alert the driver
6414 * that it should release a PCI device. The could be caused by a
6415 * Hot-Plug event, or because the driver is going to be removed from
6418 static void __devexit e1000_remove(struct pci_dev *pdev)
6420 struct net_device *netdev = pci_get_drvdata(pdev);
6421 struct e1000_adapter *adapter = netdev_priv(netdev);
6422 bool down = test_bit(__E1000_DOWN, &adapter->state);
6425 * The timers may be rescheduled, so explicitly disable them
6426 * from being rescheduled.
6429 set_bit(__E1000_DOWN, &adapter->state);
6430 del_timer_sync(&adapter->watchdog_timer);
6431 del_timer_sync(&adapter->phy_info_timer);
6433 cancel_work_sync(&adapter->reset_task);
6434 cancel_work_sync(&adapter->watchdog_task);
6435 cancel_work_sync(&adapter->downshift_task);
6436 cancel_work_sync(&adapter->update_phy_task);
6437 cancel_work_sync(&adapter->print_hang_task);
6439 if (!(netdev->flags & IFF_UP))
6440 e1000_power_down_phy(adapter);
6442 /* Don't lie to e1000_close() down the road. */
6444 clear_bit(__E1000_DOWN, &adapter->state);
6445 unregister_netdev(netdev);
6447 if (pci_dev_run_wake(pdev))
6448 pm_runtime_get_noresume(&pdev->dev);
6451 * Release control of h/w to f/w. If f/w is AMT enabled, this
6452 * would have already happened in close and is redundant.
6454 e1000e_release_hw_control(adapter);
6456 e1000e_reset_interrupt_capability(adapter);
6457 kfree(adapter->tx_ring);
6458 kfree(adapter->rx_ring);
6460 iounmap(adapter->hw.hw_addr);
6461 if (adapter->hw.flash_address)
6462 iounmap(adapter->hw.flash_address);
6463 pci_release_selected_regions(pdev,
6464 pci_select_bars(pdev, IORESOURCE_MEM));
6466 free_netdev(netdev);
6469 pci_disable_pcie_error_reporting(pdev);
6471 pci_disable_device(pdev);
6474 /* PCI Error Recovery (ERS) */
6475 static struct pci_error_handlers e1000_err_handler = {
6476 .error_detected = e1000_io_error_detected,
6477 .slot_reset = e1000_io_slot_reset,
6478 .resume = e1000_io_resume,
6481 static DEFINE_PCI_DEVICE_TABLE(e1000_pci_tbl) = {
6482 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_COPPER), board_82571 },
6483 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_FIBER), board_82571 },
6484 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER), board_82571 },
6485 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER_LP), board_82571 },
6486 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_FIBER), board_82571 },
6487 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES), board_82571 },
6488 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_DUAL), board_82571 },
6489 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_QUAD), board_82571 },
6490 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571PT_QUAD_COPPER), board_82571 },
6492 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI), board_82572 },
6493 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_COPPER), board_82572 },
6494 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_FIBER), board_82572 },
6495 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_SERDES), board_82572 },
6497 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E), board_82573 },
6498 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E_IAMT), board_82573 },
6499 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573L), board_82573 },
6501 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574L), board_82574 },
6502 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574LA), board_82574 },
6503 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82583V), board_82583 },
6505 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_DPT),
6506 board_80003es2lan },
6507 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_SPT),
6508 board_80003es2lan },
6509 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_DPT),
6510 board_80003es2lan },
6511 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_SPT),
6512 board_80003es2lan },
6514 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE), board_ich8lan },
6515 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_G), board_ich8lan },
6516 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_GT), board_ich8lan },
6517 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_AMT), board_ich8lan },
6518 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_C), board_ich8lan },
6519 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M), board_ich8lan },
6520 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M_AMT), board_ich8lan },
6521 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_82567V_3), board_ich8lan },
6523 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE), board_ich9lan },
6524 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_G), board_ich9lan },
6525 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_GT), board_ich9lan },
6526 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_AMT), board_ich9lan },
6527 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_C), board_ich9lan },
6528 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_BM), board_ich9lan },
6529 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M), board_ich9lan },
6530 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_AMT), board_ich9lan },
6531 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_V), board_ich9lan },
6533 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LM), board_ich9lan },
6534 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LF), board_ich9lan },
6535 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_V), board_ich9lan },
6537 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LM), board_ich10lan },
6538 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LF), board_ich10lan },
6539 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_V), board_ich10lan },
6541 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LM), board_pchlan },
6542 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LC), board_pchlan },
6543 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DM), board_pchlan },
6544 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DC), board_pchlan },
6546 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH2_LV_LM), board_pch2lan },
6547 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH2_LV_V), board_pch2lan },
6549 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPT_I217_LM), board_pch_lpt },
6550 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPT_I217_V), board_pch_lpt },
6552 { 0, 0, 0, 0, 0, 0, 0 } /* terminate list */
6554 MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
6557 static const struct dev_pm_ops e1000_pm_ops = {
6558 SET_SYSTEM_SLEEP_PM_OPS(e1000_suspend, e1000_resume)
6559 SET_RUNTIME_PM_OPS(e1000_runtime_suspend,
6560 e1000_runtime_resume, e1000_idle)
6564 /* PCI Device API Driver */
6565 static struct pci_driver e1000_driver = {
6566 .name = e1000e_driver_name,
6567 .id_table = e1000_pci_tbl,
6568 .probe = e1000_probe,
6569 .remove = __devexit_p(e1000_remove),
6572 .pm = &e1000_pm_ops,
6575 .shutdown = e1000_shutdown,
6576 .err_handler = &e1000_err_handler
6580 * e1000_init_module - Driver Registration Routine
6582 * e1000_init_module is the first routine called when the driver is
6583 * loaded. All it does is register with the PCI subsystem.
6585 static int __init e1000_init_module(void)
6588 pr_info("Intel(R) PRO/1000 Network Driver - %s\n",
6589 e1000e_driver_version);
6590 pr_info("Copyright(c) 1999 - 2012 Intel Corporation.\n");
6591 ret = pci_register_driver(&e1000_driver);
6595 module_init(e1000_init_module);
6598 * e1000_exit_module - Driver Exit Cleanup Routine
6600 * e1000_exit_module is called just before the driver is removed
6603 static void __exit e1000_exit_module(void)
6605 pci_unregister_driver(&e1000_driver);
6607 module_exit(e1000_exit_module);
6610 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
6611 MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver");
6612 MODULE_LICENSE("GPL");
6613 MODULE_VERSION(DRV_VERSION);