1 source "drivers/net/phy/Kconfig"
2 source "drivers/net/pfe_eth/Kconfig"
3 source "drivers/net/fsl-mc/Kconfig"
6 bool "Enable Driver Model for Ethernet drivers"
9 Enable driver model for Ethernet.
11 The eth_*() interface will be implemented by the UCLASS_ETH class
12 This is currently implemented in net/eth-uclass.c
13 Look in include/net.h for details.
16 bool "Enable Driver Model for MDIO devices"
17 depends on DM_ETH && PHYLIB
19 Enable driver model for MDIO devices
21 Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
22 stand-alone devices. Useful in particular for systems that support
23 DM_ETH and have a stand-alone MDIO hardware block shared by multiple
25 This is currently implemented in net/mdio-uclass.c
26 Look in include/miiphy.h for details.
29 bool "Enable Driver Model for MDIO MUX devices"
32 Enable driver model for MDIO MUX devices
34 Adds UCLASS_MDIO_MUX DM class supporting MDIO MUXes. Useful for
35 systems that support DM_MDIO and integrate one or multiple muxes on
37 This is currently implemented in net/mdio-mux-uclass.c
38 Look in include/miiphy.h for details.
41 depends on DM_MDIO && SANDBOX
43 bool "Sandbox: Mocked MDIO driver"
45 This driver implements dummy read/write/reset MDIO functions mimicking
46 a bus with a single PHY.
48 This driver is used in for testing in test/dm/mdio.c
50 config MDIO_MUX_SANDBOX
51 depends on DM_MDIO_MUX && MDIO_SANDBOX
53 bool "Sandbox: Mocked MDIO-MUX driver"
55 This driver implements dummy select/deselect ops mimicking a MUX on
56 the MDIO bux. It uses mdio_sandbox driver as parent MDIO.
58 This driver is used for testing in test/dm/mdio.c
61 bool "Network device support"
65 You must select Y to enable any network device support
66 Generally if you have any networking support this is a given
73 bool "Enable GbE PHY status parsing and configuration"
75 Enables support for parsing the status output and for
76 configuring GbE PHYs (affects the inner workings of some
77 commands and miiphyutil.c).
80 bool "Atheros AG7xxx Ethernet MAC support"
81 depends on DM_ETH && ARCH_ATH79
84 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
85 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
89 bool "Altera Triple-Speed Ethernet MAC support"
93 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
94 Please find details on the "Triple-Speed Ethernet MegaCore Function
95 Resource Center" of Altera.
98 bool "Broadcom SF2 (Starfighter2) Ethernet support"
101 This is an abstract framework which provides a generic interface
102 to MAC and DMA management for multiple Broadcom SoCs such as
103 Cygnus, NSP and bcm28155_ap platforms.
105 config BCM_SF2_ETH_DEFAULT_PORT
106 int "Broadcom SF2 (Starfighter2) Ethernet default port number"
107 depends on BCM_SF2_ETH
110 Default port number for the Starfighter2 ethernet driver.
112 config BCM_SF2_ETH_GMAC
113 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
114 depends on BCM_SF2_ETH
116 This flag enables the ethernet support for Broadcom platforms with
117 GMAC such as Cygnus. This driver is based on the framework provided
118 by the BCM_SF2_ETH driver.
119 Say Y to any bcmcygnus based platforms.
122 bool "BCM6348 EMAC support"
123 depends on DM_ETH && ARCH_BMIPS
129 This driver supports the BCM6348 Ethernet MAC.
132 bool "BCM6368 EMAC support"
133 depends on DM_ETH && ARCH_BMIPS
137 This driver supports the BCM6368 Ethernet MAC.
140 bool "Synopsys DWC Ethernet QOS device support"
144 This driver supports the Synopsys Designware Ethernet QOS (Quality
145 Of Service) IP block. The IP supports many options for bus type,
146 clocking/reset structure, and feature list. This driver currently
147 supports the specific configuration used in NVIDIA's Tegra186 chip,
148 but should be extensible to other combinations quite easily.
151 bool "Intel PRO/1000 Gigabit Ethernet support"
153 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
154 adapters. For more information on how to identify your adapter, go
155 to the Adapter & Driver ID Guide at:
157 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
159 config E1000_SPI_GENERIC
160 bool "Allow access to the Intel 8257x SPI bus"
163 Allow generic access to the SPI bus on the Intel 8257x, for
164 example with the "sspi" command.
167 bool "Enable SPI bus utility code"
170 Utility code for direct access to the SPI bus on Intel 8257x.
171 This does not do anything useful unless you set at least one
172 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
175 bool "Enable the e1000 command"
178 This enables the 'e1000' management command for E1000 devices. When
179 used on devices with SPI support you can reprogram the EEPROM from
183 depends on DM_ETH && SANDBOX
185 bool "Sandbox: Mocked Ethernet driver"
187 This driver simply responds with fake ARP replies and ping
188 replies that are used to verify network stack functionality
190 This driver is particularly useful in the test/dm/eth.c tests
192 config ETH_SANDBOX_RAW
193 depends on DM_ETH && SANDBOX
195 bool "Sandbox: Bridge to Linux Raw Sockets"
197 This driver is a bridge from the bottom of the network stack
198 in U-Boot to the RAW AF_PACKET API in Linux. This allows real
199 network traffic to be tested from within sandbox. See
200 doc/arch/index.rst for more details.
202 config ETH_DESIGNWARE
203 bool "Synopsys Designware Ethernet MAC"
205 imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
207 This MAC is present in SoCs from various vendors. It supports
208 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
209 provide the PHY (physical media interface).
211 config ETH_DESIGNWARE_SOCFPGA
214 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
215 depends on DM_ETH && ETH_DESIGNWARE
217 The Altera SoCFPGA requires additional configuration of the
218 Altera system manager to correctly interface with the PHY.
219 This code handles those SoC specifics.
222 bool "OpenCores 10/100 Mbps Ethernet MAC"
224 This MAC is present in OpenRISC and Xtensa XTFPGA boards.
226 config FEC_MXC_SHARE_MDIO
227 bool "Share the MDIO bus for FEC controller"
230 config FEC_MXC_MDIO_BASE
231 hex "MDIO base address for the FEC controller"
232 depends on FEC_MXC_SHARE_MDIO
234 This specifies the MDIO registers base address. It is used when
235 two FEC controllers share MDIO bus.
238 bool "FEC Ethernet controller"
239 depends on MX28 || MX5 || MX6 || MX7 || IMX8 || VF610
241 This driver supports the 10/100 Fast Ethernet controller for
245 bool "Freescale FMan ethernet support"
246 depends on ARM || PPC
248 This driver support the Freescale FMan Ethernet controller
251 bool "Ftmac100 Ethernet Support"
253 This MAC is present in Andestech SoCs.
256 bool "Ftgmac100 Ethernet Support"
260 This driver supports the Faraday's FTGMAC100 Gigabit SoC
261 Ethernet controller that can be found on Aspeed SoCs (which
264 It is fully compliant with IEEE 802.3 specification for
265 10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
266 Mbps Ethernet and includes Reduced Media Independent
267 Interface (RMII) and Reduced Gigabit Media Independent
268 Interface (RGMII) interfaces. It adopts an AHB bus interface
269 and integrates a link list DMA engine with direct M-Bus
270 accesses for transmitting and receiving packets. It has
271 independent TX/RX fifos, supports half and full duplex (1000
272 Mbps mode only supports full duplex), flow control for full
273 duplex and backpressure for half duplex.
275 The FTGMAC100 also implements IP, TCP, UDP checksum offloads
276 and supports IEEE 802.1Q VLAN tag insertion and removal. It
277 offers high-priority transmit queue for QoS and CoS
282 bool "Marvell Orion5x/Kirkwood network interface support"
283 depends on KIRKWOOD || ORION5X
284 select PHYLIB if DM_ETH
286 This driver supports the network interface units in the
287 Marvell Orion5x and Kirkwood SoCs
290 bool "Marvell Armada XP/385/3700 network interface support"
291 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
294 This driver supports the network interface units in the
295 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
298 bool "Marvell Armada 375/7K/8K network interface support"
299 depends on ARMADA_375 || ARMADA_8K
302 This driver supports the network interface units in the
303 Marvell ARMADA 375, 7K and 8K SoCs.
306 bool "Cadence MACB/GEM Ethernet Interface"
310 The Cadence MACB ethernet interface is found on many Atmel
311 AT91 and SAMA5 parts. This driver also supports the Cadence
312 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
313 Say Y to include support for the MACB/GEM chip.
316 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
319 The Cadence MACB ethernet interface was used on Zynq platform.
320 Say Y to enable support for the MACB/GEM in Zynq chip.
323 bool "MediaTek MT7628 Ethernet Interface"
324 depends on SOC_MT7628
327 The MediaTek MT7628 ethernet interface is used on MT7628 and
331 bool "Intel Platform Controller Hub EG20T GMAC driver"
332 depends on DM_ETH && DM_PCI
335 This MAC is present in Intel Platform Controller Hub EG20T. It
336 supports 10/100/1000 Mbps operation.
341 Enable the support of the Reduced Gigabit Media-Independent
347 Enable support of the Media-Independent Interface (MII)
350 bool "Realtek 8139 series Ethernet controller driver"
352 This driver supports Realtek 8139 series fast ethernet family of
353 PCI chipsets/adapters.
356 bool "Realtek 8169 series Ethernet controller driver"
358 This driver supports Realtek 8169 series gigabit ethernet family of
359 PCI/PCIe chipsets/adapters.
362 bool "SMSC LAN911x and LAN921x controller driver"
367 hex "SMC911X Base Address"
369 Define this to hold the physical address
370 of the device (I/O space)
373 prompt "SMC911X bus width"
374 default SMC911X_16_BIT
376 config SMC911X_32_BIT
377 bool "Enable 32-bit interface"
379 config SMC911X_16_BIT
380 bool "Enable 16-bit interface"
382 Define this if data bus is 16 bits. If your processor
383 automatically converts one 32 bit word to two 16 bit
384 words you may also try CONFIG_SMC911X_32_BIT.
390 bool "Enable Allwinner GMAC Ethernet support"
392 Enable the support for Sun7i GMAC Ethernet controller
394 config SUN7I_GMAC_FORCE_TXERR
395 bool "Force PA17 as gmac function"
396 depends on SUN7I_GMAC
398 Some ethernet phys needs TXERR control. Since the GMAC
399 doesn't have such signal, setting PA17 as GMAC function
400 makes the pin output low, which enables data transmission.
403 bool "Allwinner Sun4i Ethernet MAC support"
407 This driver supports the Allwinner based SUN4I Ethernet MAC.
410 bool "Allwinner Sun8i Ethernet MAC support"
415 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
416 It can be found in H3/A64/A83T based SoCs and compatible with both
417 External and Internal PHYs.
420 bool "Renesas SH Ethernet MAC"
423 This driver supports the Ethernet for Renesas SH and ARM SoCs.
425 source "drivers/net/ti/Kconfig"
427 config XILINX_AXIEMAC
428 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
431 bool "Xilinx AXI Ethernet"
433 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
435 config XILINX_EMACLITE
436 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
439 bool "Xilinx Ethernetlite"
441 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
444 depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL)
446 bool "Xilinx Ethernet GEM"
448 This MAC is present in Xilinx Zynq and ZynqMP SoCs.
451 bool "Microchip PIC32 Ethernet Support"
452 depends on DM_ETH && MACH_PIC32
455 This driver implements 10/100 Mbps Ethernet and MAC layer for
456 Microchip PIC32 microcontrollers.
459 bool "Rockchip Synopsys Designware Ethernet MAC"
460 depends on DM_ETH && ETH_DESIGNWARE
462 This driver provides Rockchip SoCs network support based on the
463 Synopsys Designware driver.
466 bool "Renesas Ethernet AVB MAC"
467 depends on DM_ETH && RCAR_GEN3
470 This driver implements support for the Ethernet AVB block in
471 Renesas M3 and H3 SoCs.
474 bool "Fast Ethernet Controller on MPC8XX"
478 This driver implements support for the Fast Ethernet Controller
482 bool "Socionext AVE Ethernet support"
483 depends on DM_ETH && ARCH_UNIPHIER
488 This driver implements support for the Socionext AVE Ethernet
489 controller, as found on the Socionext UniPhier family.
491 source "drivers/net/mscc_eswitch/Kconfig"
495 depends on MPC8XX_FEC
500 depends on ETHER_ON_FEC1
503 Define to the hardcoded PHY address which corresponds
504 to the given FEC; i. e.
505 #define CONFIG_FEC1_PHY 4
506 means that the PHY with address 4 is connected to FEC1
508 When set to -1, means to probe for first available.
512 depends on ETHER_ON_FEC1
515 The PHY does not have a RXERR line (RMII only).
516 (so program the FEC to ignore it).
520 depends on MPC8XX_FEC && MPC885
525 depends on ETHER_ON_FEC2
528 Define to the hardcoded PHY address which corresponds
529 to the given FEC; i. e.
530 #define CONFIG_FEC1_PHY 4
531 means that the PHY with address 4 is connected to FEC1
533 When set to -1, means to probe for first available.
535 config FEC2_PHY_NORXERR
537 depends on ETHER_ON_FEC2
540 The PHY does not have a RXERR line (RMII only).
541 (so program the FEC to ignore it).
543 config SYS_DPAA_QBMAN
544 bool "Device tree fixup for QBMan on freescale SOCs"
545 depends on (ARM || PPC) && !SPL_BUILD
546 default y if ARCH_B4860 || \
565 QBman fixups to allow deep sleep in DPAA 1 SOCs
569 bool "Enable Three-Speed Ethernet Controller"
571 This driver implements support for the (Enhanced) Three-Speed
572 Ethernet Controller found on Freescale SoCs.
575 bool "MediaTek Ethernet GMAC Driver"
581 This Driver support MediaTek Ethernet GMAC
582 Say Y to enable support for the MediaTek Ethernet GMAC.
584 config HIGMACV300_ETH
585 bool "HiSilicon Gigabit Ethernet Controller"
590 This driver supports HIGMACV300 Ethernet controller found on
594 bool "NXP ENETC Ethernet controller"
595 depends on DM_PCI && DM_ETH && DM_MDIO
597 This driver supports the NXP ENETC Ethernet controller found on some
600 config MDIO_MUX_I2CREG
601 bool "MDIO MUX accessed as a register over I2C"
602 depends on DM_MDIO_MUX && DM_I2C
604 This driver is used for MDIO muxes driven by writing to a register of
605 an I2C chip. The board it was developed for uses a mux controlled by
606 on-board FPGA which in turn is accessed as a chip over I2C.
609 bool "Marvell MDIO interface support"
612 This driver supports the MDIO interface found in the network
613 interface units of the Marvell EBU SoCs (Kirkwood, Orion5x,
614 Dove, Armada 370, Armada XP, Armada 37xx and Armada7K/8K/8KP).
616 This driver is used by the MVPP2 and MVNETA drivers.