1 source "drivers/net/phy/Kconfig"
2 source "drivers/net/pfe_eth/Kconfig"
5 bool "Enable Driver Model for Ethernet drivers"
8 Enable driver model for Ethernet.
10 The eth_*() interface will be implemented by the UCLASS_ETH class
11 This is currently implemented in net/eth-uclass.c
12 Look in include/net.h for details.
15 bool "Enable Driver Model for MDIO devices"
16 depends on DM_ETH && PHYLIB
18 Enable driver model for MDIO devices
20 Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
21 stand-alone devices. Useful in particular for systems that support
22 DM_ETH and have a stand-alone MDIO hardware block shared by multiple
24 This is currently implemented in net/mdio-uclass.c
25 Look in include/miiphy.h for details.
28 depends on DM_MDIO && SANDBOX
30 bool "Sandbox: Mocked MDIO driver"
32 This driver implements dummy read/write/reset MDIO functions mimicking
33 a bus with a single PHY.
35 This driver is used in for testing in test/dm/mdio.c
38 bool "Network device support"
42 You must select Y to enable any network device support
43 Generally if you have any networking support this is a given
50 bool "Enable GbE PHY status parsing and configuration"
52 Enables support for parsing the status output and for
53 configuring GbE PHYs (affects the inner workings of some
54 commands and miiphyutil.c).
57 bool "Atheros AG7xxx Ethernet MAC support"
58 depends on DM_ETH && ARCH_ATH79
61 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
62 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
66 bool "Altera Triple-Speed Ethernet MAC support"
70 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
71 Please find details on the "Triple-Speed Ethernet MegaCore Function
72 Resource Center" of Altera.
75 bool "Broadcom SF2 (Starfighter2) Ethernet support"
78 This is an abstract framework which provides a generic interface
79 to MAC and DMA management for multiple Broadcom SoCs such as
80 Cygnus, NSP and bcm28155_ap platforms.
82 config BCM_SF2_ETH_DEFAULT_PORT
83 int "Broadcom SF2 (Starfighter2) Ethernet default port number"
84 depends on BCM_SF2_ETH
87 Default port number for the Starfighter2 ethernet driver.
89 config BCM_SF2_ETH_GMAC
90 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
91 depends on BCM_SF2_ETH
93 This flag enables the ethernet support for Broadcom platforms with
94 GMAC such as Cygnus. This driver is based on the framework provided
95 by the BCM_SF2_ETH driver.
96 Say Y to any bcmcygnus based platforms.
99 bool "BCM6348 EMAC support"
100 depends on DM_ETH && ARCH_BMIPS
106 This driver supports the BCM6348 Ethernet MAC.
109 bool "BCM6368 EMAC support"
110 depends on DM_ETH && ARCH_BMIPS
114 This driver supports the BCM6368 Ethernet MAC.
117 bool "Synopsys DWC Ethernet QOS device support"
121 This driver supports the Synopsys Designware Ethernet QOS (Quality
122 Of Service) IP block. The IP supports many options for bus type,
123 clocking/reset structure, and feature list. This driver currently
124 supports the specific configuration used in NVIDIA's Tegra186 chip,
125 but should be extensible to other combinations quite easily.
128 bool "Intel PRO/1000 Gigabit Ethernet support"
130 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
131 adapters. For more information on how to identify your adapter, go
132 to the Adapter & Driver ID Guide at:
134 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
136 config E1000_SPI_GENERIC
137 bool "Allow access to the Intel 8257x SPI bus"
140 Allow generic access to the SPI bus on the Intel 8257x, for
141 example with the "sspi" command.
144 bool "Enable SPI bus utility code"
147 Utility code for direct access to the SPI bus on Intel 8257x.
148 This does not do anything useful unless you set at least one
149 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
152 bool "Enable the e1000 command"
155 This enables the 'e1000' management command for E1000 devices. When
156 used on devices with SPI support you can reprogram the EEPROM from
160 depends on DM_ETH && SANDBOX
162 bool "Sandbox: Mocked Ethernet driver"
164 This driver simply responds with fake ARP replies and ping
165 replies that are used to verify network stack functionality
167 This driver is particularly useful in the test/dm/eth.c tests
169 config ETH_SANDBOX_RAW
170 depends on DM_ETH && SANDBOX
172 bool "Sandbox: Bridge to Linux Raw Sockets"
174 This driver is a bridge from the bottom of the network stack
175 in U-Boot to the RAW AF_PACKET API in Linux. This allows real
176 network traffic to be tested from within sandbox. See
177 board/sandbox/README.sandbox for more details.
179 config ETH_DESIGNWARE
180 bool "Synopsys Designware Ethernet MAC"
182 imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
184 This MAC is present in SoCs from various vendors. It supports
185 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
186 provide the PHY (physical media interface).
188 config ETH_DESIGNWARE_SOCFPGA
191 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
192 depends on DM_ETH && ETH_DESIGNWARE
194 The Altera SoCFPGA requires additional configuration of the
195 Altera system manager to correctly interface with the PHY.
196 This code handles those SoC specifics.
199 bool "OpenCores 10/100 Mbps Ethernet MAC"
201 This MAC is present in OpenRISC and Xtensa XTFPGA boards.
203 config FEC_MXC_SHARE_MDIO
204 bool "Share the MDIO bus for FEC controller"
207 config FEC_MXC_MDIO_BASE
208 hex "MDIO base address for the FEC controller"
209 depends on FEC_MXC_SHARE_MDIO
211 This specifies the MDIO registers base address. It is used when
212 two FEC controllers share MDIO bus.
215 bool "FEC Ethernet controller"
216 depends on MX5 || MX6 || MX7 || IMX8 || VF610
218 This driver supports the 10/100 Fast Ethernet controller for
222 bool "Freescale FMan ethernet support"
223 depends on ARM || PPC
225 This driver support the Freescale FMan Ethernet controller
228 bool "Ftmac100 Ethernet Support"
230 This MAC is present in Andestech SoCs.
233 bool "Ftgmac100 Ethernet Support"
237 This driver supports the Faraday's FTGMAC100 Gigabit SoC
238 Ethernet controller that can be found on Aspeed SoCs (which
241 It is fully compliant with IEEE 802.3 specification for
242 10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
243 Mbps Ethernet and includes Reduced Media Independent
244 Interface (RMII) and Reduced Gigabit Media Independent
245 Interface (RGMII) interfaces. It adopts an AHB bus interface
246 and integrates a link list DMA engine with direct M-Bus
247 accesses for transmitting and receiving packets. It has
248 independent TX/RX fifos, supports half and full duplex (1000
249 Mbps mode only supports full duplex), flow control for full
250 duplex and backpressure for half duplex.
252 The FTGMAC100 also implements IP, TCP, UDP checksum offloads
253 and supports IEEE 802.1Q VLAN tag insertion and removal. It
254 offers high-priority transmit queue for QoS and CoS
259 bool "Marvell Orion5x/Kirkwood network interface support"
260 depends on KIRKWOOD || ORION5X
261 select PHYLIB if DM_ETH
263 This driver supports the network interface units in the
264 Marvell Orion5x and Kirkwood SoCs
267 bool "Marvell Armada XP/385/3700 network interface support"
268 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
271 This driver supports the network interface units in the
272 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
275 bool "Marvell Armada 375/7K/8K network interface support"
276 depends on ARMADA_375 || ARMADA_8K
279 This driver supports the network interface units in the
280 Marvell ARMADA 375, 7K and 8K SoCs.
283 bool "Cadence MACB/GEM Ethernet Interface"
287 The Cadence MACB ethernet interface is found on many Atmel
288 AT91 and SAMA5 parts. This driver also supports the Cadence
289 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
290 Say Y to include support for the MACB/GEM chip.
293 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
296 The Cadence MACB ethernet interface was used on Zynq platform.
297 Say Y to enable support for the MACB/GEM in Zynq chip.
300 bool "MediaTek MT7628 Ethernet Interface"
301 depends on SOC_MT7628
303 The MediaTek MT7628 ethernet interface is used on MT7628 and
307 bool "Intel Platform Controller Hub EG20T GMAC driver"
308 depends on DM_ETH && DM_PCI
311 This MAC is present in Intel Platform Controller Hub EG20T. It
312 supports 10/100/1000 Mbps operation.
317 Enable the support of the Reduced Gigabit Media-Independent
323 Enable support of the Media-Independent Interface (MII)
326 bool "Realtek 8139 series Ethernet controller driver"
328 This driver supports Realtek 8139 series fast ethernet family of
329 PCI chipsets/adapters.
332 bool "Realtek 8169 series Ethernet controller driver"
334 This driver supports Realtek 8169 series gigabit ethernet family of
335 PCI/PCIe chipsets/adapters.
338 bool "SMSC LAN911x and LAN921x controller driver"
343 hex "SMC911X Base Address"
345 Define this to hold the physical address
346 of the device (I/O space)
349 prompt "SMC911X bus width"
350 default SMC911X_16_BIT
352 config SMC911X_32_BIT
353 bool "Enable 32-bit interface"
355 config SMC911X_16_BIT
356 bool "Enable 16-bit interface"
358 Define this if data bus is 16 bits. If your processor
359 automatically converts one 32 bit word to two 16 bit
360 words you may also try CONFIG_SMC911X_32_BIT.
366 bool "Enable Allwinner GMAC Ethernet support"
368 Enable the support for Sun7i GMAC Ethernet controller
370 config SUN7I_GMAC_FORCE_TXERR
371 bool "Force PA17 as gmac function"
372 depends on SUN7I_GMAC
374 Some ethernet phys needs TXERR control. Since the GMAC
375 doesn't have such signal, setting PA17 as GMAC function
376 makes the pin output low, which enables data transmission.
379 bool "Allwinner Sun4i Ethernet MAC support"
383 This driver supports the Allwinner based SUN4I Ethernet MAC.
386 bool "Allwinner Sun8i Ethernet MAC support"
391 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
392 It can be found in H3/A64/A83T based SoCs and compatible with both
393 External and Internal PHYs.
396 bool "Renesas SH Ethernet MAC"
399 This driver supports the Ethernet for Renesas SH and ARM SoCs.
401 source "drivers/net/ti/Kconfig"
403 config XILINX_AXIEMAC
404 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
407 bool "Xilinx AXI Ethernet"
409 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
411 config XILINX_EMACLITE
412 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
415 bool "Xilinx Ethernetlite"
417 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
420 depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL)
422 bool "Xilinx Ethernet GEM"
424 This MAC is present in Xilinx Zynq and ZynqMP SoCs.
427 bool "Microchip PIC32 Ethernet Support"
428 depends on DM_ETH && MACH_PIC32
431 This driver implements 10/100 Mbps Ethernet and MAC layer for
432 Microchip PIC32 microcontrollers.
435 bool "Rockchip Synopsys Designware Ethernet MAC"
436 depends on DM_ETH && ETH_DESIGNWARE
438 This driver provides Rockchip SoCs network support based on the
439 Synopsys Designware driver.
442 bool "Renesas Ethernet AVB MAC"
443 depends on DM_ETH && RCAR_GEN3
446 This driver implements support for the Ethernet AVB block in
447 Renesas M3 and H3 SoCs.
450 bool "Fast Ethernet Controller on MPC8XX"
454 This driver implements support for the Fast Ethernet Controller
458 bool "Socionext AVE Ethernet support"
459 depends on DM_ETH && ARCH_UNIPHIER
464 This driver implements support for the Socionext AVE Ethernet
465 controller, as found on the Socionext UniPhier family.
467 source "drivers/net/mscc_eswitch/Kconfig"
471 depends on MPC8XX_FEC
476 depends on ETHER_ON_FEC1
479 Define to the hardcoded PHY address which corresponds
480 to the given FEC; i. e.
481 #define CONFIG_FEC1_PHY 4
482 means that the PHY with address 4 is connected to FEC1
484 When set to -1, means to probe for first available.
488 depends on ETHER_ON_FEC1
491 The PHY does not have a RXERR line (RMII only).
492 (so program the FEC to ignore it).
496 depends on MPC8XX_FEC && MPC885
501 depends on ETHER_ON_FEC2
504 Define to the hardcoded PHY address which corresponds
505 to the given FEC; i. e.
506 #define CONFIG_FEC1_PHY 4
507 means that the PHY with address 4 is connected to FEC1
509 When set to -1, means to probe for first available.
511 config FEC2_PHY_NORXERR
513 depends on ETHER_ON_FEC2
516 The PHY does not have a RXERR line (RMII only).
517 (so program the FEC to ignore it).
519 config SYS_DPAA_QBMAN
520 bool "Device tree fixup for QBMan on freescale SOCs"
521 depends on (ARM || PPC) && !SPL_BUILD
522 default y if ARCH_B4860 || \
541 QBman fixups to allow deep sleep in DPAA 1 SOCs
545 bool "Enable Three-Speed Ethernet Controller"
547 This driver implements support for the (Enhanced) Three-Speed
548 Ethernet Controller found on Freescale SoCs.
551 bool "MediaTek Ethernet GMAC Driver"
557 This Driver support MediaTek Ethernet GMAC
558 Say Y to enable support for the MediaTek Ethernet GMAC.
560 config HIGMACV300_ETH
561 bool "HiSilicon Gigabit Ethernet Controller"
566 This driver supports HIGMACV300 Ethernet controller found on