1 source "drivers/net/phy/Kconfig"
2 source "drivers/net/pfe_eth/Kconfig"
3 source "drivers/net/fsl-mc/Kconfig"
6 bool "Enable Driver Model for Ethernet drivers"
9 Enable driver model for Ethernet.
11 The eth_*() interface will be implemented by the UCLASS_ETH class
12 This is currently implemented in net/eth-uclass.c
13 Look in include/net.h for details.
16 bool "Enable Driver Model for MDIO devices"
17 depends on DM_ETH && PHYLIB
19 Enable driver model for MDIO devices
21 Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
22 stand-alone devices. Useful in particular for systems that support
23 DM_ETH and have a stand-alone MDIO hardware block shared by multiple
25 This is currently implemented in net/mdio-uclass.c
26 Look in include/miiphy.h for details.
29 bool "Enable Driver Model for MDIO MUX devices"
32 Enable driver model for MDIO MUX devices
34 Adds UCLASS_MDIO_MUX DM class supporting MDIO MUXes. Useful for
35 systems that support DM_MDIO and integrate one or multiple muxes on
37 This is currently implemented in net/mdio-mux-uclass.c
38 Look in include/miiphy.h for details.
41 depends on DM_MDIO && SANDBOX
43 bool "Sandbox: Mocked MDIO driver"
45 This driver implements dummy read/write/reset MDIO functions mimicking
46 a bus with a single PHY.
48 This driver is used in for testing in test/dm/mdio.c
50 config MDIO_MUX_SANDBOX
51 depends on DM_MDIO_MUX && MDIO_SANDBOX
53 bool "Sandbox: Mocked MDIO-MUX driver"
55 This driver implements dummy select/deselect ops mimicking a MUX on
56 the MDIO bux. It uses mdio_sandbox driver as parent MDIO.
58 This driver is used for testing in test/dm/mdio.c
61 bool "Enable Driver Model for Ethernet Generic PHY drivers"
64 Enable driver model for Ethernet Generic PHY .
67 bool "Network device support"
71 You must select Y to enable any network device support
72 Generally if you have any networking support this is a given
79 bool "Enable GbE PHY status parsing and configuration"
81 Enables support for parsing the status output and for
82 configuring GbE PHYs (affects the inner workings of some
83 commands and miiphyutil.c).
86 bool "Atheros AG7xxx Ethernet MAC support"
87 depends on DM_ETH && ARCH_ATH79
90 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
91 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
95 bool "Altera Triple-Speed Ethernet MAC support"
99 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
100 Please find details on the "Triple-Speed Ethernet MegaCore Function
101 Resource Center" of Altera.
104 bool "Broadcom SF2 (Starfighter2) Ethernet support"
107 This is an abstract framework which provides a generic interface
108 to MAC and DMA management for multiple Broadcom SoCs such as
109 Cygnus, NSP and bcm28155_ap platforms.
111 config BCM_SF2_ETH_DEFAULT_PORT
112 int "Broadcom SF2 (Starfighter2) Ethernet default port number"
113 depends on BCM_SF2_ETH
116 Default port number for the Starfighter2 ethernet driver.
118 config BCM_SF2_ETH_GMAC
119 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
120 depends on BCM_SF2_ETH
122 This flag enables the ethernet support for Broadcom platforms with
123 GMAC such as Cygnus. This driver is based on the framework provided
124 by the BCM_SF2_ETH driver.
125 Say Y to any bcmcygnus based platforms.
128 bool "BCM6348 EMAC support"
129 depends on DM_ETH && ARCH_BMIPS
135 This driver supports the BCM6348 Ethernet MAC.
138 bool "BCM6368 EMAC support"
139 depends on DM_ETH && ARCH_BMIPS
143 This driver supports the BCM6368 Ethernet MAC.
146 bool "BCMGENET V5 support"
150 This driver supports the BCMGENET Ethernet MAC.
153 bool "Synopsys DWC Ethernet QOS device support"
157 This driver supports the Synopsys Designware Ethernet QOS (Quality
158 Of Service) IP block. The IP supports many options for bus type,
159 clocking/reset structure, and feature list.
161 config DWC_ETH_QOS_IMX
162 bool "Synopsys DWC Ethernet QOS device support for IMX"
163 depends on DWC_ETH_QOS
165 The Synopsys Designware Ethernet QOS IP block with the specific
166 configuration used in IMX soc.
168 config DWC_ETH_QOS_STM32
169 bool "Synopsys DWC Ethernet QOS device support for STM32"
170 depends on DWC_ETH_QOS
171 default y if ARCH_STM32MP
173 The Synopsys Designware Ethernet QOS IP block with the specific
174 configuration used in STM32MP soc.
176 config DWC_ETH_QOS_TEGRA186
177 bool "Synopsys DWC Ethernet QOS device support for TEGRA186"
178 depends on DWC_ETH_QOS
179 default y if TEGRA186
181 The Synopsys Designware Ethernet QOS IP block with specific
182 configuration used in NVIDIA's Tegra186 chip.
185 bool "Intel PRO/1000 Gigabit Ethernet support"
186 depends on (DM_ETH && DM_PCI) || !DM_ETH
188 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
189 adapters. For more information on how to identify your adapter, go
190 to the Adapter & Driver ID Guide at:
192 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
194 config E1000_SPI_GENERIC
195 bool "Allow access to the Intel 8257x SPI bus"
198 Allow generic access to the SPI bus on the Intel 8257x, for
199 example with the "sspi" command.
202 bool "Enable SPI bus utility code"
205 Utility code for direct access to the SPI bus on Intel 8257x.
206 This does not do anything useful unless you set at least one
207 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
210 bool "Enable the e1000 command"
213 This enables the 'e1000' management command for E1000 devices. When
214 used on devices with SPI support you can reprogram the EEPROM from
218 bool "Intel PRO/100 82557/82559/82559ER Fast Ethernet support"
220 This driver supports Intel(R) PRO/100 82557/82559/82559ER fast
221 ethernet family of adapters.
224 depends on DM_ETH && SANDBOX
226 bool "Sandbox: Mocked Ethernet driver"
228 This driver simply responds with fake ARP replies and ping
229 replies that are used to verify network stack functionality
231 This driver is particularly useful in the test/dm/eth.c tests
233 config ETH_SANDBOX_RAW
234 depends on DM_ETH && SANDBOX
236 bool "Sandbox: Bridge to Linux Raw Sockets"
238 This driver is a bridge from the bottom of the network stack
239 in U-Boot to the RAW AF_PACKET API in Linux. This allows real
240 network traffic to be tested from within sandbox. See
241 doc/arch/index.rst for more details.
243 config ETH_DESIGNWARE
244 bool "Synopsys Designware Ethernet MAC"
246 imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
248 This MAC is present in SoCs from various vendors. It supports
249 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
250 provide the PHY (physical media interface).
252 config ETH_DESIGNWARE_SOCFPGA
255 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
256 depends on DM_ETH && ETH_DESIGNWARE
258 The Altera SoCFPGA requires additional configuration of the
259 Altera system manager to correctly interface with the PHY.
260 This code handles those SoC specifics.
262 config ETH_DESIGNWARE_S700
263 bool "Actins S700 glue driver for Synopsys Designware Ethernet MAC"
264 depends on DM_ETH && ETH_DESIGNWARE
266 This provides glue layer to use Synopsys Designware Ethernet MAC
267 present on Actions S700 SoC.
270 bool "OpenCores 10/100 Mbps Ethernet MAC"
272 This MAC is present in OpenRISC and Xtensa XTFPGA boards.
274 config FEC_MXC_SHARE_MDIO
275 bool "Share the MDIO bus for FEC controller"
278 config FEC_MXC_MDIO_BASE
279 hex "MDIO base address for the FEC controller"
280 depends on FEC_MXC_SHARE_MDIO
282 This specifies the MDIO registers base address. It is used when
283 two FEC controllers share MDIO bus.
286 bool "FEC Ethernet controller"
287 depends on MX28 || MX5 || MX6 || MX7 || IMX8 || IMX8M || VF610
289 This driver supports the 10/100 Fast Ethernet controller for
293 bool "Freescale FMan ethernet support"
294 depends on ARM || PPC
296 This driver support the Freescale FMan Ethernet controller
299 bool "Ftmac100 Ethernet Support"
301 This MAC is present in Andestech SoCs.
304 bool "Ftgmac100 Ethernet Support"
308 This driver supports the Faraday's FTGMAC100 Gigabit SoC
309 Ethernet controller that can be found on Aspeed SoCs (which
312 It is fully compliant with IEEE 802.3 specification for
313 10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
314 Mbps Ethernet and includes Reduced Media Independent
315 Interface (RMII) and Reduced Gigabit Media Independent
316 Interface (RGMII) interfaces. It adopts an AHB bus interface
317 and integrates a link list DMA engine with direct M-Bus
318 accesses for transmitting and receiving packets. It has
319 independent TX/RX fifos, supports half and full duplex (1000
320 Mbps mode only supports full duplex), flow control for full
321 duplex and backpressure for half duplex.
323 The FTGMAC100 also implements IP, TCP, UDP checksum offloads
324 and supports IEEE 802.1Q VLAN tag insertion and removal. It
325 offers high-priority transmit queue for QoS and CoS
330 bool "ColdFire Ethernet Support"
334 This driver supports the network interface units in the
338 bool "ColdFire DMA Ethernet Support"
342 This driver supports the network interface units in the
346 bool "Microchip KS8851-MLL controller driver"
348 The Microchip KS8851 parallel bus external ethernet interface chip.
352 config KS8851_MLL_BASEADDR
353 hex "Microchip KS8851-MLL Base Address"
355 Define this to hold the physical address of the device (I/O space)
360 bool "Marvell Orion5x/Kirkwood network interface support"
361 depends on ARCH_KIRKWOOD || ARCH_ORION5X
362 select PHYLIB if DM_ETH
364 This driver supports the network interface units in the
365 Marvell Orion5x and Kirkwood SoCs
368 bool "Marvell Armada XP/385/3700 network interface support"
369 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
372 This driver supports the network interface units in the
373 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
376 bool "Marvell Armada 375/7K/8K network interface support"
377 depends on ARMADA_375 || ARMADA_8K
382 This driver supports the network interface units in the
383 Marvell ARMADA 375, 7K and 8K SoCs.
386 bool "Cadence MACB/GEM Ethernet Interface"
390 The Cadence MACB ethernet interface is found on many Atmel
391 AT91 and SAMA5 parts. This driver also supports the Cadence
392 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
393 Say Y to include support for the MACB/GEM chip.
396 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
399 The Cadence MACB ethernet interface was used on Zynq platform.
400 Say Y to enable support for the MACB/GEM in Zynq chip.
403 bool "MediaTek MT7628 Ethernet Interface"
404 depends on SOC_MT7628
407 The MediaTek MT7628 ethernet interface is used on MT7628 and
411 bool "Intel Platform Controller Hub EG20T GMAC driver"
412 depends on DM_ETH && DM_PCI
415 This MAC is present in Intel Platform Controller Hub EG20T. It
416 supports 10/100/1000 Mbps operation.
421 Enable the support of the Reduced Gigabit Media-Independent
427 Enable support of the Media-Independent Interface (MII)
430 bool "AMD PCnet series Ethernet controller driver"
432 This driver supports AMD PCnet series fast ethernet family of
433 PCI chipsets/adapters.
436 bool "Realtek 8139 series Ethernet controller driver"
438 This driver supports Realtek 8139 series fast ethernet family of
439 PCI chipsets/adapters.
442 bool "Realtek 8169 series Ethernet controller driver"
444 This driver supports Realtek 8169 series gigabit ethernet family of
445 PCI/PCIe chipsets/adapters.
448 bool "SMSC LAN911x and LAN921x controller driver"
454 hex "SMC911X Base Address"
456 Define this to hold the physical address
457 of the device (I/O space)
461 prompt "SMC911X bus width"
462 default SMC911X_16_BIT
464 config SMC911X_32_BIT
465 bool "Enable 32-bit interface"
467 config SMC911X_16_BIT
468 bool "Enable 16-bit interface"
470 Define this if data bus is 16 bits. If your processor
471 automatically converts one 32 bit word to two 16 bit
472 words you may also try CONFIG_SMC911X_32_BIT.
478 bool "Enable Allwinner GMAC Ethernet support"
480 Enable the support for Sun7i GMAC Ethernet controller
482 config SUN7I_GMAC_FORCE_TXERR
483 bool "Force PA17 as gmac function"
484 depends on SUN7I_GMAC
486 Some ethernet phys needs TXERR control. Since the GMAC
487 doesn't have such signal, setting PA17 as GMAC function
488 makes the pin output low, which enables data transmission.
491 bool "Allwinner Sun4i Ethernet MAC support"
495 This driver supports the Allwinner based SUN4I Ethernet MAC.
498 bool "Allwinner Sun8i Ethernet MAC support"
503 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
504 It can be found in H3/A64/A83T based SoCs and compatible with both
505 External and Internal PHYs.
508 bool "Renesas SH Ethernet MAC"
511 This driver supports the Ethernet for Renesas SH and ARM SoCs.
513 source "drivers/net/ti/Kconfig"
516 bool "DEC Tulip DC2114x Ethernet support"
517 depends on (DM_ETH && DM_PCI) || !DM_ETH
519 This driver supports DEC DC2114x Fast ethernet chips.
521 config XILINX_AXIEMAC
522 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
525 bool "Xilinx AXI Ethernet"
527 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
529 config XILINX_EMACLITE
530 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
533 bool "Xilinx Ethernetlite"
535 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
538 depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL)
540 bool "Xilinx Ethernet GEM"
542 This MAC is present in Xilinx Zynq and ZynqMP SoCs.
545 bool "Microchip PIC32 Ethernet Support"
546 depends on DM_ETH && MACH_PIC32
549 This driver implements 10/100 Mbps Ethernet and MAC layer for
550 Microchip PIC32 microcontrollers.
553 bool "Rockchip Synopsys Designware Ethernet MAC"
554 depends on DM_ETH && ETH_DESIGNWARE
556 This driver provides Rockchip SoCs network support based on the
557 Synopsys Designware driver.
560 bool "Renesas Ethernet AVB MAC"
561 depends on DM_ETH && RCAR_GEN3
564 This driver implements support for the Ethernet AVB block in
565 Renesas M3 and H3 SoCs.
568 bool "Fast Ethernet Controller on MPC8XX"
572 This driver implements support for the Fast Ethernet Controller
576 bool "Socionext AVE Ethernet support"
577 depends on DM_ETH && ARCH_UNIPHIER
582 This driver implements support for the Socionext AVE Ethernet
583 controller, as found on the Socionext UniPhier family.
585 source "drivers/net/mscc_eswitch/Kconfig"
589 depends on MPC8XX_FEC
594 depends on ETHER_ON_FEC1
597 Define to the hardcoded PHY address which corresponds
598 to the given FEC; i. e.
599 #define CONFIG_FEC1_PHY 4
600 means that the PHY with address 4 is connected to FEC1
602 When set to -1, means to probe for first available.
606 depends on ETHER_ON_FEC1
609 The PHY does not have a RXERR line (RMII only).
610 (so program the FEC to ignore it).
614 depends on MPC8XX_FEC && MPC885
619 depends on ETHER_ON_FEC2
622 Define to the hardcoded PHY address which corresponds
623 to the given FEC; i. e.
624 #define CONFIG_FEC1_PHY 4
625 means that the PHY with address 4 is connected to FEC1
627 When set to -1, means to probe for first available.
629 config FEC2_PHY_NORXERR
631 depends on ETHER_ON_FEC2
634 The PHY does not have a RXERR line (RMII only).
635 (so program the FEC to ignore it).
637 config SYS_DPAA_QBMAN
638 bool "Device tree fixup for QBMan on freescale SOCs"
639 depends on (ARM || PPC) && !SPL_BUILD
640 default y if ARCH_B4860 || \
659 QBman fixups to allow deep sleep in DPAA 1 SOCs
663 bool "Enable Three-Speed Ethernet Controller"
665 This driver implements support for the (Enhanced) Three-Speed
666 Ethernet Controller found on Freescale SoCs.
669 bool "MediaTek Ethernet GMAC Driver"
675 This Driver support MediaTek Ethernet GMAC
676 Say Y to enable support for the MediaTek Ethernet GMAC.
678 config HIGMACV300_ETH
679 bool "HiSilicon Gigabit Ethernet Controller"
684 This driver supports HIGMACV300 Ethernet controller found on
688 bool "NXP ENETC Ethernet controller"
689 depends on DM_PCI && DM_ETH && DM_MDIO
691 This driver supports the NXP ENETC Ethernet controller found on some
694 config MDIO_MUX_I2CREG
695 bool "MDIO MUX accessed as a register over I2C"
696 depends on DM_MDIO_MUX && DM_I2C
698 This driver is used for MDIO muxes driven by writing to a register of
699 an I2C chip. The board it was developed for uses a mux controlled by
700 on-board FPGA which in turn is accessed as a chip over I2C.
703 bool "Marvell MDIO interface support"
706 This driver supports the MDIO interface found in the network
707 interface units of the Marvell EBU SoCs (Kirkwood, Orion5x,
708 Dove, Armada 370, Armada XP, Armada 37xx and Armada7K/8K/8KP).
710 This driver is used by the MVPP2 and MVNETA drivers.
713 bool "NXP Layerscape MDIO interface support"
716 This driver supports the MDIO bus found on the Fman 10G Ethernet MACs and
717 on the mEMAC (which supports both Clauses 22 and 45).