1 source "drivers/net/phy/Kconfig"
2 source "drivers/net/pfe_eth/Kconfig"
3 source "drivers/net/fsl-mc/Kconfig"
6 bool "Enable Driver Model for Ethernet drivers"
9 Enable driver model for Ethernet.
11 The eth_*() interface will be implemented by the UCLASS_ETH class
12 This is currently implemented in net/eth-uclass.c
13 Look in include/net.h for details.
16 bool "Enable Driver Model for MDIO devices"
17 depends on DM_ETH && PHYLIB
19 Enable driver model for MDIO devices
21 Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
22 stand-alone devices. Useful in particular for systems that support
23 DM_ETH and have a stand-alone MDIO hardware block shared by multiple
25 This is currently implemented in net/mdio-uclass.c
26 Look in include/miiphy.h for details.
29 bool "Enable Driver Model for MDIO MUX devices"
32 Enable driver model for MDIO MUX devices
34 Adds UCLASS_MDIO_MUX DM class supporting MDIO MUXes. Useful for
35 systems that support DM_MDIO and integrate one or multiple muxes on
37 This is currently implemented in net/mdio-mux-uclass.c
38 Look in include/miiphy.h for details.
41 bool "Enable Driver Model for DSA switches"
42 depends on DM_ETH && DM_MDIO
45 Enable driver model for DSA switches
47 Adds UCLASS_DSA class supporting switches that follow the Distributed
48 Switch Architecture (DSA). These switches rely on the presence of a
49 management switch port connected to an Ethernet controller capable of
50 receiving frames from the switch. This host Ethernet controller is
51 called the "master" Ethernet interface in DSA terminology.
52 This is currently implemented in net/dsa-uclass.c, refer to
53 include/net/dsa.h for API details.
56 depends on DM_MDIO && SANDBOX
58 bool "Sandbox: Mocked MDIO driver"
60 This driver implements dummy read/write/reset MDIO functions mimicking
61 a bus with a single PHY.
63 This driver is used in for testing in test/dm/mdio.c
65 config MDIO_MUX_SANDBOX
66 depends on DM_MDIO_MUX && MDIO_SANDBOX
68 bool "Sandbox: Mocked MDIO-MUX driver"
70 This driver implements dummy select/deselect ops mimicking a MUX on
71 the MDIO bux. It uses mdio_sandbox driver as parent MDIO.
73 This driver is used for testing in test/dm/mdio.c
76 bool "Enable Driver Model for Ethernet Generic PHY drivers"
79 Enable driver model for Ethernet Generic PHY .
82 depends on DM_DSA && SANDBOX
84 bool "Sandbox: Mocked DSA driver"
86 This driver implements a dummy DSA switch connected to a dummy sandbox
87 Ethernet device used as DSA master, to test DSA class code, including
88 exported DSA API and datapath processing of Ethernet traffic.
91 bool "Network device support"
95 You must select Y to enable any network device support
96 Generally if you have any networking support this is a given
103 bool "Enable GbE PHY status parsing and configuration"
105 Enables support for parsing the status output and for
106 configuring GbE PHYs (affects the inner workings of some
107 commands and miiphyutil.c).
110 bool "Atheros AG7xxx Ethernet MAC support"
111 depends on DM_ETH && ARCH_ATH79
114 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
115 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
119 bool "Altera Triple-Speed Ethernet MAC support"
123 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
124 Please find details on the "Triple-Speed Ethernet MegaCore Function
125 Resource Center" of Altera.
128 bool "Broadcom SF2 (Starfighter2) Ethernet support"
131 This is an abstract framework which provides a generic interface
132 to MAC and DMA management for multiple Broadcom SoCs such as
133 Cygnus, NSP and bcm28155_ap platforms.
135 config BCM_SF2_ETH_DEFAULT_PORT
136 int "Broadcom SF2 (Starfighter2) Ethernet default port number"
137 depends on BCM_SF2_ETH
140 Default port number for the Starfighter2 ethernet driver.
142 config BCM_SF2_ETH_GMAC
143 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
144 depends on BCM_SF2_ETH
146 This flag enables the ethernet support for Broadcom platforms with
147 GMAC such as Cygnus. This driver is based on the framework provided
148 by the BCM_SF2_ETH driver.
149 Say Y to any bcmcygnus based platforms.
152 bool "BCM6348 EMAC support"
153 depends on DM_ETH && ARCH_BMIPS
159 This driver supports the BCM6348 Ethernet MAC.
162 bool "BCM6368 EMAC support"
163 depends on DM_ETH && ARCH_BMIPS
167 This driver supports the BCM6368 Ethernet MAC.
170 bool "BCMGENET V5 support"
174 This driver supports the BCMGENET Ethernet MAC.
176 config CORTINA_NI_ENET
177 bool "Cortina-Access Ethernet driver"
178 depends on DM_ETH && CORTINA_PLATFORM
180 This driver supports the Cortina-Access Ethernet MAC for
181 all supported CAxxxx SoCs.
184 bool "Calxeda XGMAC support"
187 This driver supports the XGMAC in Calxeda Highbank and Midway
191 bool "Synopsys DWC Ethernet QOS device support"
195 This driver supports the Synopsys Designware Ethernet QOS (Quality
196 Of Service) IP block. The IP supports many options for bus type,
197 clocking/reset structure, and feature list.
199 config DWC_ETH_QOS_IMX
200 bool "Synopsys DWC Ethernet QOS device support for IMX"
201 depends on DWC_ETH_QOS
203 The Synopsys Designware Ethernet QOS IP block with the specific
204 configuration used in IMX soc.
206 config DWC_ETH_QOS_STM32
207 bool "Synopsys DWC Ethernet QOS device support for STM32"
208 depends on DWC_ETH_QOS
209 default y if ARCH_STM32MP
211 The Synopsys Designware Ethernet QOS IP block with the specific
212 configuration used in STM32MP soc.
214 config DWC_ETH_QOS_TEGRA186
215 bool "Synopsys DWC Ethernet QOS device support for TEGRA186"
216 depends on DWC_ETH_QOS
217 default y if TEGRA186
219 The Synopsys Designware Ethernet QOS IP block with specific
220 configuration used in NVIDIA's Tegra186 chip.
223 bool "Intel PRO/1000 Gigabit Ethernet support"
224 depends on (DM_ETH && DM_PCI) || !DM_ETH
226 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
227 adapters. For more information on how to identify your adapter, go
228 to the Adapter & Driver ID Guide at:
230 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
232 config E1000_SPI_GENERIC
233 bool "Allow access to the Intel 8257x SPI bus"
236 Allow generic access to the SPI bus on the Intel 8257x, for
237 example with the "sspi" command.
240 bool "Enable SPI bus utility code"
243 Utility code for direct access to the SPI bus on Intel 8257x.
244 This does not do anything useful unless you set at least one
245 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
248 bool "Enable the e1000 command"
251 This enables the 'e1000' management command for E1000 devices. When
252 used on devices with SPI support you can reprogram the EEPROM from
256 bool "Intel PRO/100 82557/82559/82559ER Fast Ethernet support"
258 This driver supports Intel(R) PRO/100 82557/82559/82559ER fast
259 ethernet family of adapters.
262 depends on DM_ETH && SANDBOX
264 bool "Sandbox: Mocked Ethernet driver"
266 This driver simply responds with fake ARP replies and ping
267 replies that are used to verify network stack functionality
269 This driver is particularly useful in the test/dm/eth.c tests
271 config ETH_SANDBOX_RAW
272 depends on DM_ETH && SANDBOX
274 bool "Sandbox: Bridge to Linux Raw Sockets"
276 This driver is a bridge from the bottom of the network stack
277 in U-Boot to the RAW AF_PACKET API in Linux. This allows real
278 network traffic to be tested from within sandbox. See
279 doc/arch/index.rst for more details.
281 config ETH_DESIGNWARE
282 bool "Synopsys Designware Ethernet MAC"
284 imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
286 This MAC is present in SoCs from various vendors. It supports
287 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
288 provide the PHY (physical media interface).
290 config ETH_DESIGNWARE_MESON8B
291 bool "Amlogic Meson8b and later glue driver for Synopsys Designware Ethernet MAC"
293 select ETH_DESIGNWARE
295 This provides glue layer to use Synopsys Designware Ethernet MAC
296 present on the Amlogic Meson8b, GX, AXG & G12A SoCs.
298 config ETH_DESIGNWARE_SOCFPGA
301 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
302 depends on DM_ETH && ETH_DESIGNWARE
304 The Altera SoCFPGA requires additional configuration of the
305 Altera system manager to correctly interface with the PHY.
306 This code handles those SoC specifics.
308 config ETH_DESIGNWARE_S700
309 bool "Actins S700 glue driver for Synopsys Designware Ethernet MAC"
310 depends on DM_ETH && ETH_DESIGNWARE
312 This provides glue layer to use Synopsys Designware Ethernet MAC
313 present on Actions S700 SoC.
316 bool "OpenCores 10/100 Mbps Ethernet MAC"
318 This MAC is present in OpenRISC and Xtensa XTFPGA boards.
320 config FEC_MXC_SHARE_MDIO
321 bool "Share the MDIO bus for FEC controller"
324 config FEC_MXC_MDIO_BASE
325 hex "MDIO base address for the FEC controller"
326 depends on FEC_MXC_SHARE_MDIO
328 This specifies the MDIO registers base address. It is used when
329 two FEC controllers share MDIO bus.
332 bool "FEC Ethernet controller"
333 depends on MX28 || MX5 || MX6 || MX7 || IMX8 || IMX8M || VF610
335 This driver supports the 10/100 Fast Ethernet controller for
339 bool "Freescale FMan ethernet support"
340 depends on ARM || PPC
342 This driver support the Freescale FMan Ethernet controller
345 bool "Ftmac100 Ethernet Support"
347 This MAC is present in Andestech SoCs.
350 bool "Ftgmac100 Ethernet Support"
354 This driver supports the Faraday's FTGMAC100 Gigabit SoC
355 Ethernet controller that can be found on Aspeed SoCs (which
358 It is fully compliant with IEEE 802.3 specification for
359 10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
360 Mbps Ethernet and includes Reduced Media Independent
361 Interface (RMII) and Reduced Gigabit Media Independent
362 Interface (RGMII) interfaces. It adopts an AHB bus interface
363 and integrates a link list DMA engine with direct M-Bus
364 accesses for transmitting and receiving packets. It has
365 independent TX/RX fifos, supports half and full duplex (1000
366 Mbps mode only supports full duplex), flow control for full
367 duplex and backpressure for half duplex.
369 The FTGMAC100 also implements IP, TCP, UDP checksum offloads
370 and supports IEEE 802.1Q VLAN tag insertion and removal. It
371 offers high-priority transmit queue for QoS and CoS
376 bool "ColdFire Ethernet Support"
380 This driver supports the network interface units in the
384 bool "ColdFire DMA Ethernet Support"
388 This driver supports the network interface units in the
392 bool "Microchip KS8851-MLL controller driver"
394 The Microchip KS8851 parallel bus external ethernet interface chip.
398 config KS8851_MLL_BASEADDR
399 hex "Microchip KS8851-MLL Base Address"
401 Define this to hold the physical address of the device (I/O space)
406 bool "Marvell Orion5x/Kirkwood network interface support"
407 depends on ARCH_KIRKWOOD || ARCH_ORION5X
408 select PHYLIB if DM_ETH
410 This driver supports the network interface units in the
411 Marvell Orion5x and Kirkwood SoCs
414 bool "Marvell Armada XP/385/3700 network interface support"
415 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
418 This driver supports the network interface units in the
419 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
422 bool "Marvell Armada 375/7K/8K network interface support"
423 depends on ARMADA_375 || ARMADA_8K
428 This driver supports the network interface units in the
429 Marvell ARMADA 375, 7K and 8K SoCs.
432 bool "Cadence MACB/GEM Ethernet Interface"
436 The Cadence MACB ethernet interface is found on many Atmel
437 AT91 and SAMA5 parts. This driver also supports the Cadence
438 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
439 Say Y to include support for the MACB/GEM chip.
442 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
445 The Cadence MACB ethernet interface was used on Zynq platform.
446 Say Y to enable support for the MACB/GEM in Zynq chip.
449 bool "MediaTek MT7620 Ethernet Interface"
450 depends on SOC_MT7620
456 The MediaTek MT7620 ethernet interface is used on MT7620 based
457 boards. It has a built-in switch with two configurable ports which
458 can connect to external PHY/MACs.
461 bool "MediaTek MT7628 Ethernet Interface"
462 depends on SOC_MT7628
465 The MediaTek MT7628 ethernet interface is used on MT7628 and
469 bool "OcteonTX Ethernet support"
470 depends on ARCH_OCTEONTX
473 You must select Y to enable network device support for
474 OcteonTX SoCs. If unsure, say n
477 bool "OcteonTX2 Ethernet support"
478 depends on ARCH_OCTEONTX2
479 select OCTEONTX2_CGX_INTF
481 You must select Y to enable network device support for
482 OcteonTX2 SoCs. If unsure, say n
485 bool "OcteonTX SMI Device support"
486 depends on ARCH_OCTEONTX || ARCH_OCTEONTX2
488 You must select Y to enable SMI controller support for
489 OcteonTX or OcteonTX2 SoCs. If unsure, say n
491 config OCTEONTX2_CGX_INTF
492 bool "OcteonTX2 CGX ATF interface support"
493 depends on ARCH_OCTEONTX2
494 default y if ARCH_OCTEONTX2
496 You must select Y to enable CGX ATF interface support for
497 OcteonTX2 SoCs. If unsure, say n
500 bool "Intel Platform Controller Hub EG20T GMAC driver"
501 depends on DM_ETH && DM_PCI
504 This MAC is present in Intel Platform Controller Hub EG20T. It
505 supports 10/100/1000 Mbps operation.
510 Enable the support of the Reduced Gigabit Media-Independent
516 Enable support of the Media-Independent Interface (MII)
519 bool "AMD PCnet series Ethernet controller driver"
521 This driver supports AMD PCnet series fast ethernet family of
522 PCI chipsets/adapters.
524 source "drivers/net/qe/Kconfig"
527 bool "Realtek 8139 series Ethernet controller driver"
529 This driver supports Realtek 8139 series fast ethernet family of
530 PCI chipsets/adapters.
533 bool "Realtek 8169 series Ethernet controller driver"
535 This driver supports Realtek 8169 series gigabit ethernet family of
536 PCI/PCIe chipsets/adapters.
539 bool "SMSC LAN911x and LAN921x controller driver"
545 hex "SMC911X Base Address"
547 Define this to hold the physical address
548 of the device (I/O space)
551 config SMC911X_32_BIT
552 bool "Enable SMC911X 32-bit interface"
555 Define this if data bus is 32 bits. If your processor use a
556 narrower 16 bit bus or cannot convert one 32 bit word to two 16 bit
557 words, leave this to "n".
562 bool "Enable Allwinner GMAC Ethernet support"
564 Enable the support for Sun7i GMAC Ethernet controller
566 config SUN7I_GMAC_FORCE_TXERR
567 bool "Force PA17 as gmac function"
568 depends on SUN7I_GMAC
570 Some ethernet phys needs TXERR control. Since the GMAC
571 doesn't have such signal, setting PA17 as GMAC function
572 makes the pin output low, which enables data transmission.
575 bool "Allwinner Sun4i Ethernet MAC support"
579 This driver supports the Allwinner based SUN4I Ethernet MAC.
582 bool "Allwinner Sun8i Ethernet MAC support"
587 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
588 It can be found in H3/A64/A83T based SoCs and compatible with both
589 External and Internal PHYs.
592 bool "Renesas SH Ethernet MAC"
595 This driver supports the Ethernet for Renesas SH and ARM SoCs.
597 source "drivers/net/ti/Kconfig"
600 bool "DEC Tulip DC2114x Ethernet support"
601 depends on (DM_ETH && DM_PCI) || !DM_ETH
603 This driver supports DEC DC2114x Fast ethernet chips.
605 config XILINX_AXIEMAC
609 bool "Xilinx AXI Ethernet"
611 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
613 config XILINX_EMACLITE
617 bool "Xilinx Ethernetlite"
619 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
624 bool "Xilinx Ethernet GEM"
626 This MAC is present in Xilinx Zynq and ZynqMP SoCs.
629 bool "Microchip PIC32 Ethernet Support"
630 depends on DM_ETH && MACH_PIC32
633 This driver implements 10/100 Mbps Ethernet and MAC layer for
634 Microchip PIC32 microcontrollers.
637 bool "Rockchip Synopsys Designware Ethernet MAC"
638 depends on DM_ETH && ETH_DESIGNWARE
640 This driver provides Rockchip SoCs network support based on the
641 Synopsys Designware driver.
644 bool "Renesas Ethernet AVB MAC"
645 depends on DM_ETH && RCAR_GEN3
648 This driver implements support for the Ethernet AVB block in
649 Renesas M3 and H3 SoCs.
652 bool "Fast Ethernet Controller on MPC8XX"
656 This driver implements support for the Fast Ethernet Controller
660 bool "Socionext AVE Ethernet support"
661 depends on DM_ETH && ARCH_UNIPHIER
666 This driver implements support for the Socionext AVE Ethernet
667 controller, as found on the Socionext UniPhier family.
670 bool "Socionext NETSEC Ethernet support"
671 depends on DM_ETH && SYNQUACER_SPI
674 This driver implements support for the Socionext SynQuacer NETSEC
675 ethernet controller, as found on the Socionext SynQuacer family.
677 source "drivers/net/mscc_eswitch/Kconfig"
681 depends on MPC8XX_FEC
686 depends on ETHER_ON_FEC1
689 Define to the hardcoded PHY address which corresponds
690 to the given FEC; i. e.
691 #define CONFIG_FEC1_PHY 4
692 means that the PHY with address 4 is connected to FEC1
694 When set to -1, means to probe for first available.
698 depends on ETHER_ON_FEC1
701 The PHY does not have a RXERR line (RMII only).
702 (so program the FEC to ignore it).
706 depends on MPC8XX_FEC && MPC885
711 depends on ETHER_ON_FEC2
714 Define to the hardcoded PHY address which corresponds
715 to the given FEC; i. e.
716 #define CONFIG_FEC1_PHY 4
717 means that the PHY with address 4 is connected to FEC1
719 When set to -1, means to probe for first available.
721 config FEC2_PHY_NORXERR
723 depends on ETHER_ON_FEC2
726 The PHY does not have a RXERR line (RMII only).
727 (so program the FEC to ignore it).
729 config SYS_DPAA_QBMAN
730 bool "Device tree fixup for QBMan on freescale SOCs"
731 depends on (ARM || PPC) && !SPL_BUILD
732 default y if ARCH_B4860 || \
749 QBman fixups to allow deep sleep in DPAA 1 SOCs
753 bool "Enable Three-Speed Ethernet Controller"
755 This driver implements support for the (Enhanced) Three-Speed
756 Ethernet Controller found on Freescale SoCs.
759 bool "MediaTek Ethernet GMAC Driver"
765 This Driver support MediaTek Ethernet GMAC
766 Say Y to enable support for the MediaTek Ethernet GMAC.
768 config HIGMACV300_ETH
769 bool "HiSilicon Gigabit Ethernet Controller"
774 This driver supports HIGMACV300 Ethernet controller found on
778 bool "NXP ENETC Ethernet controller"
779 depends on DM_PCI && DM_ETH && DM_MDIO
781 This driver supports the NXP ENETC Ethernet controller found on some
784 config MDIO_MUX_I2CREG
785 bool "MDIO MUX accessed as a register over I2C"
786 depends on DM_MDIO_MUX && DM_I2C
788 This driver is used for MDIO muxes driven by writing to a register of
789 an I2C chip. The board it was developed for uses a mux controlled by
790 on-board FPGA which in turn is accessed as a chip over I2C.
793 bool "Qualcomm IPQ4019 MDIO interface support"
796 This driver supports the MDIO interface found in Qualcomm
797 IPQ40xx series Soc-s.
800 bool "Marvell MDIO interface support"
803 This driver supports the MDIO interface found in the network
804 interface units of the Marvell EBU SoCs (Kirkwood, Orion5x,
805 Dove, Armada 370, Armada XP, Armada 37xx and Armada7K/8K/8KP).
807 This driver is used by the MVPP2 and MVNETA drivers.
810 bool "NXP Layerscape MDIO interface support"
813 This driver supports the MDIO bus found on the Fman 10G Ethernet MACs and
814 on the mEMAC (which supports both Clauses 22 and 45).
816 config MDIO_MUX_MMIOREG
817 bool "MDIO MUX accessed as a MMIO register access"
818 depends on DM_MDIO_MUX
820 This driver is used for MDIO muxes driven by writing to a register in
821 the MMIO physical memory.
823 config MDIO_MUX_MESON_G12A
824 bool "MDIO MUX for Amlogic Meson G12A SoCs"
825 depends on DM_MDIO_MUX
827 This driver is used for the MDIO mux found on the Amlogic G12A & compatible