1 source "drivers/net/phy/Kconfig"
2 source "drivers/net/pfe_eth/Kconfig"
3 source "drivers/net/fsl-mc/Kconfig"
6 bool "Enable Driver Model for Ethernet drivers"
9 Enable driver model for Ethernet.
11 The eth_*() interface will be implemented by the UCLASS_ETH class
12 This is currently implemented in net/eth-uclass.c
13 Look in include/net.h for details.
16 bool "Enable Driver Model for MDIO devices"
17 depends on DM_ETH && PHYLIB
19 Enable driver model for MDIO devices
21 Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
22 stand-alone devices. Useful in particular for systems that support
23 DM_ETH and have a stand-alone MDIO hardware block shared by multiple
25 This is currently implemented in net/mdio-uclass.c
26 Look in include/miiphy.h for details.
29 bool "Enable Driver Model for MDIO MUX devices"
32 Enable driver model for MDIO MUX devices
34 Adds UCLASS_MDIO_MUX DM class supporting MDIO MUXes. Useful for
35 systems that support DM_MDIO and integrate one or multiple muxes on
37 This is currently implemented in net/mdio-mux-uclass.c
38 Look in include/miiphy.h for details.
41 bool "Enable Driver Model for DSA switches"
42 depends on DM_ETH && DM_MDIO
45 Enable driver model for DSA switches
47 Adds UCLASS_DSA class supporting switches that follow the Distributed
48 Switch Architecture (DSA). These switches rely on the presence of a
49 management switch port connected to an Ethernet controller capable of
50 receiving frames from the switch. This host Ethernet controller is
51 called the "master" Ethernet interface in DSA terminology.
52 This is currently implemented in net/dsa-uclass.c, refer to
53 include/net/dsa.h for API details.
56 depends on DM_MDIO && SANDBOX
58 bool "Sandbox: Mocked MDIO driver"
60 This driver implements dummy read/write/reset MDIO functions mimicking
61 a bus with a single PHY.
63 This driver is used in for testing in test/dm/mdio.c
65 config MDIO_MUX_SANDBOX
66 depends on DM_MDIO_MUX && MDIO_SANDBOX
68 bool "Sandbox: Mocked MDIO-MUX driver"
70 This driver implements dummy select/deselect ops mimicking a MUX on
71 the MDIO bux. It uses mdio_sandbox driver as parent MDIO.
73 This driver is used for testing in test/dm/mdio.c
76 bool "Enable Driver Model for Ethernet Generic PHY drivers"
79 Enable driver model for Ethernet Generic PHY .
82 depends on DM_DSA && SANDBOX
84 bool "Sandbox: Mocked DSA driver"
86 This driver implements a dummy DSA switch connected to a dummy sandbox
87 Ethernet device used as DSA master, to test DSA class code, including
88 exported DSA API and datapath processing of Ethernet traffic.
91 bool "Network device support"
95 You must select Y to enable any network device support
96 Generally if you have any networking support this is a given
103 bool "Enable GbE PHY status parsing and configuration"
105 Enables support for parsing the status output and for
106 configuring GbE PHYs (affects the inner workings of some
107 commands and miiphyutil.c).
110 bool "Atheros AG7xxx Ethernet MAC support"
111 depends on DM_ETH && ARCH_ATH79
114 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
115 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
119 bool "Altera Triple-Speed Ethernet MAC support"
123 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
124 Please find details on the "Triple-Speed Ethernet MegaCore Function
125 Resource Center" of Altera.
128 bool "Broadcom SF2 (Starfighter2) Ethernet support"
131 This is an abstract framework which provides a generic interface
132 to MAC and DMA management for multiple Broadcom SoCs such as
133 Cygnus, NSP and bcm28155_ap platforms.
135 config BCM_SF2_ETH_DEFAULT_PORT
136 int "Broadcom SF2 (Starfighter2) Ethernet default port number"
137 depends on BCM_SF2_ETH
140 Default port number for the Starfighter2 ethernet driver.
142 config BCM_SF2_ETH_GMAC
143 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
144 depends on BCM_SF2_ETH
146 This flag enables the ethernet support for Broadcom platforms with
147 GMAC such as Cygnus. This driver is based on the framework provided
148 by the BCM_SF2_ETH driver.
149 Say Y to any bcmcygnus based platforms.
152 bool "BCM6348 EMAC support"
153 depends on DM_ETH && ARCH_BMIPS
159 This driver supports the BCM6348 Ethernet MAC.
162 bool "BCM6368 EMAC support"
163 depends on DM_ETH && ARCH_BMIPS
167 This driver supports the BCM6368 Ethernet MAC.
170 bool "BCMGENET V5 support"
174 This driver supports the BCMGENET Ethernet MAC.
176 config CORTINA_NI_ENET
177 bool "Cortina-Access Ethernet driver"
178 depends on DM_ETH && CORTINA_PLATFORM
180 This driver supports the Cortina-Access Ethernet MAC for
181 all supported CAxxxx SoCs.
184 bool "Synopsys DWC Ethernet QOS device support"
188 This driver supports the Synopsys Designware Ethernet QOS (Quality
189 Of Service) IP block. The IP supports many options for bus type,
190 clocking/reset structure, and feature list.
192 config DWC_ETH_QOS_IMX
193 bool "Synopsys DWC Ethernet QOS device support for IMX"
194 depends on DWC_ETH_QOS
196 The Synopsys Designware Ethernet QOS IP block with the specific
197 configuration used in IMX soc.
199 config DWC_ETH_QOS_STM32
200 bool "Synopsys DWC Ethernet QOS device support for STM32"
201 depends on DWC_ETH_QOS
202 default y if ARCH_STM32MP
204 The Synopsys Designware Ethernet QOS IP block with the specific
205 configuration used in STM32MP soc.
207 config DWC_ETH_QOS_TEGRA186
208 bool "Synopsys DWC Ethernet QOS device support for TEGRA186"
209 depends on DWC_ETH_QOS
210 default y if TEGRA186
212 The Synopsys Designware Ethernet QOS IP block with specific
213 configuration used in NVIDIA's Tegra186 chip.
216 bool "Intel PRO/1000 Gigabit Ethernet support"
217 depends on (DM_ETH && DM_PCI) || !DM_ETH
219 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
220 adapters. For more information on how to identify your adapter, go
221 to the Adapter & Driver ID Guide at:
223 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
225 config E1000_SPI_GENERIC
226 bool "Allow access to the Intel 8257x SPI bus"
229 Allow generic access to the SPI bus on the Intel 8257x, for
230 example with the "sspi" command.
233 bool "Enable SPI bus utility code"
236 Utility code for direct access to the SPI bus on Intel 8257x.
237 This does not do anything useful unless you set at least one
238 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
241 bool "Enable the e1000 command"
244 This enables the 'e1000' management command for E1000 devices. When
245 used on devices with SPI support you can reprogram the EEPROM from
249 bool "Intel PRO/100 82557/82559/82559ER Fast Ethernet support"
251 This driver supports Intel(R) PRO/100 82557/82559/82559ER fast
252 ethernet family of adapters.
255 depends on DM_ETH && SANDBOX
257 bool "Sandbox: Mocked Ethernet driver"
259 This driver simply responds with fake ARP replies and ping
260 replies that are used to verify network stack functionality
262 This driver is particularly useful in the test/dm/eth.c tests
264 config ETH_SANDBOX_RAW
265 depends on DM_ETH && SANDBOX
267 bool "Sandbox: Bridge to Linux Raw Sockets"
269 This driver is a bridge from the bottom of the network stack
270 in U-Boot to the RAW AF_PACKET API in Linux. This allows real
271 network traffic to be tested from within sandbox. See
272 doc/arch/index.rst for more details.
274 config ETH_DESIGNWARE
275 bool "Synopsys Designware Ethernet MAC"
277 imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
279 This MAC is present in SoCs from various vendors. It supports
280 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
281 provide the PHY (physical media interface).
283 config ETH_DESIGNWARE_MESON8B
284 bool "Amlogic Meson8b and later glue driver for Synopsys Designware Ethernet MAC"
286 select ETH_DESIGNWARE
288 This provides glue layer to use Synopsys Designware Ethernet MAC
289 present on the Amlogic Meson8b, GX, AXG & G12A SoCs.
291 config ETH_DESIGNWARE_SOCFPGA
294 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
295 depends on DM_ETH && ETH_DESIGNWARE
297 The Altera SoCFPGA requires additional configuration of the
298 Altera system manager to correctly interface with the PHY.
299 This code handles those SoC specifics.
301 config ETH_DESIGNWARE_S700
302 bool "Actins S700 glue driver for Synopsys Designware Ethernet MAC"
303 depends on DM_ETH && ETH_DESIGNWARE
305 This provides glue layer to use Synopsys Designware Ethernet MAC
306 present on Actions S700 SoC.
309 bool "OpenCores 10/100 Mbps Ethernet MAC"
311 This MAC is present in OpenRISC and Xtensa XTFPGA boards.
313 config FEC_MXC_SHARE_MDIO
314 bool "Share the MDIO bus for FEC controller"
317 config FEC_MXC_MDIO_BASE
318 hex "MDIO base address for the FEC controller"
319 depends on FEC_MXC_SHARE_MDIO
321 This specifies the MDIO registers base address. It is used when
322 two FEC controllers share MDIO bus.
325 bool "FEC Ethernet controller"
326 depends on MX28 || MX5 || MX6 || MX7 || IMX8 || IMX8M || VF610
328 This driver supports the 10/100 Fast Ethernet controller for
332 bool "Freescale FMan ethernet support"
333 depends on ARM || PPC
335 This driver support the Freescale FMan Ethernet controller
338 bool "Ftmac100 Ethernet Support"
340 This MAC is present in Andestech SoCs.
343 bool "Ftgmac100 Ethernet Support"
347 This driver supports the Faraday's FTGMAC100 Gigabit SoC
348 Ethernet controller that can be found on Aspeed SoCs (which
351 It is fully compliant with IEEE 802.3 specification for
352 10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
353 Mbps Ethernet and includes Reduced Media Independent
354 Interface (RMII) and Reduced Gigabit Media Independent
355 Interface (RGMII) interfaces. It adopts an AHB bus interface
356 and integrates a link list DMA engine with direct M-Bus
357 accesses for transmitting and receiving packets. It has
358 independent TX/RX fifos, supports half and full duplex (1000
359 Mbps mode only supports full duplex), flow control for full
360 duplex and backpressure for half duplex.
362 The FTGMAC100 also implements IP, TCP, UDP checksum offloads
363 and supports IEEE 802.1Q VLAN tag insertion and removal. It
364 offers high-priority transmit queue for QoS and CoS
369 bool "ColdFire Ethernet Support"
373 This driver supports the network interface units in the
377 bool "ColdFire DMA Ethernet Support"
381 This driver supports the network interface units in the
385 bool "Microchip KS8851-MLL controller driver"
387 The Microchip KS8851 parallel bus external ethernet interface chip.
391 config KS8851_MLL_BASEADDR
392 hex "Microchip KS8851-MLL Base Address"
394 Define this to hold the physical address of the device (I/O space)
399 bool "Marvell Orion5x/Kirkwood network interface support"
400 depends on ARCH_KIRKWOOD || ARCH_ORION5X
401 select PHYLIB if DM_ETH
403 This driver supports the network interface units in the
404 Marvell Orion5x and Kirkwood SoCs
407 bool "Marvell Armada XP/385/3700 network interface support"
408 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
411 This driver supports the network interface units in the
412 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
415 bool "Marvell Armada 375/7K/8K network interface support"
416 depends on ARMADA_375 || ARMADA_8K
421 This driver supports the network interface units in the
422 Marvell ARMADA 375, 7K and 8K SoCs.
425 bool "Cadence MACB/GEM Ethernet Interface"
429 The Cadence MACB ethernet interface is found on many Atmel
430 AT91 and SAMA5 parts. This driver also supports the Cadence
431 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
432 Say Y to include support for the MACB/GEM chip.
435 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
438 The Cadence MACB ethernet interface was used on Zynq platform.
439 Say Y to enable support for the MACB/GEM in Zynq chip.
442 bool "MediaTek MT7620 Ethernet Interface"
443 depends on SOC_MT7620
449 The MediaTek MT7620 ethernet interface is used on MT7620 based
450 boards. It has a built-in switch with two configurable ports which
451 can connect to external PHY/MACs.
454 bool "MediaTek MT7628 Ethernet Interface"
455 depends on SOC_MT7628
458 The MediaTek MT7628 ethernet interface is used on MT7628 and
462 bool "OcteonTX Ethernet support"
463 depends on ARCH_OCTEONTX
466 You must select Y to enable network device support for
467 OcteonTX SoCs. If unsure, say n
470 bool "OcteonTX2 Ethernet support"
471 depends on ARCH_OCTEONTX2
472 select OCTEONTX2_CGX_INTF
474 You must select Y to enable network device support for
475 OcteonTX2 SoCs. If unsure, say n
478 bool "OcteonTX SMI Device support"
479 depends on ARCH_OCTEONTX || ARCH_OCTEONTX2
481 You must select Y to enable SMI controller support for
482 OcteonTX or OcteonTX2 SoCs. If unsure, say n
484 config OCTEONTX2_CGX_INTF
485 bool "OcteonTX2 CGX ATF interface support"
486 depends on ARCH_OCTEONTX2
487 default y if ARCH_OCTEONTX2
489 You must select Y to enable CGX ATF interface support for
490 OcteonTX2 SoCs. If unsure, say n
493 bool "Intel Platform Controller Hub EG20T GMAC driver"
494 depends on DM_ETH && DM_PCI
497 This MAC is present in Intel Platform Controller Hub EG20T. It
498 supports 10/100/1000 Mbps operation.
503 Enable the support of the Reduced Gigabit Media-Independent
509 Enable support of the Media-Independent Interface (MII)
512 bool "AMD PCnet series Ethernet controller driver"
514 This driver supports AMD PCnet series fast ethernet family of
515 PCI chipsets/adapters.
517 source "drivers/net/qe/Kconfig"
520 bool "Realtek 8139 series Ethernet controller driver"
522 This driver supports Realtek 8139 series fast ethernet family of
523 PCI chipsets/adapters.
526 bool "Realtek 8169 series Ethernet controller driver"
528 This driver supports Realtek 8169 series gigabit ethernet family of
529 PCI/PCIe chipsets/adapters.
532 bool "SMSC LAN911x and LAN921x controller driver"
538 hex "SMC911X Base Address"
540 Define this to hold the physical address
541 of the device (I/O space)
545 prompt "SMC911X bus width"
546 default SMC911X_16_BIT
548 config SMC911X_32_BIT
549 bool "Enable 32-bit interface"
551 config SMC911X_16_BIT
552 bool "Enable 16-bit interface"
554 Define this if data bus is 16 bits. If your processor
555 automatically converts one 32 bit word to two 16 bit
556 words you may also try CONFIG_SMC911X_32_BIT.
562 bool "Enable Allwinner GMAC Ethernet support"
564 Enable the support for Sun7i GMAC Ethernet controller
566 config SUN7I_GMAC_FORCE_TXERR
567 bool "Force PA17 as gmac function"
568 depends on SUN7I_GMAC
570 Some ethernet phys needs TXERR control. Since the GMAC
571 doesn't have such signal, setting PA17 as GMAC function
572 makes the pin output low, which enables data transmission.
575 bool "Allwinner Sun4i Ethernet MAC support"
579 This driver supports the Allwinner based SUN4I Ethernet MAC.
582 bool "Allwinner Sun8i Ethernet MAC support"
587 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
588 It can be found in H3/A64/A83T based SoCs and compatible with both
589 External and Internal PHYs.
592 bool "Renesas SH Ethernet MAC"
595 This driver supports the Ethernet for Renesas SH and ARM SoCs.
597 source "drivers/net/ti/Kconfig"
600 bool "DEC Tulip DC2114x Ethernet support"
601 depends on (DM_ETH && DM_PCI) || !DM_ETH
603 This driver supports DEC DC2114x Fast ethernet chips.
605 config XILINX_AXIEMAC
609 bool "Xilinx AXI Ethernet"
611 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
613 config XILINX_EMACLITE
617 bool "Xilinx Ethernetlite"
619 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
624 bool "Xilinx Ethernet GEM"
626 This MAC is present in Xilinx Zynq and ZynqMP SoCs.
629 bool "Microchip PIC32 Ethernet Support"
630 depends on DM_ETH && MACH_PIC32
633 This driver implements 10/100 Mbps Ethernet and MAC layer for
634 Microchip PIC32 microcontrollers.
637 bool "Rockchip Synopsys Designware Ethernet MAC"
638 depends on DM_ETH && ETH_DESIGNWARE
640 This driver provides Rockchip SoCs network support based on the
641 Synopsys Designware driver.
644 bool "Renesas Ethernet AVB MAC"
645 depends on DM_ETH && RCAR_GEN3
648 This driver implements support for the Ethernet AVB block in
649 Renesas M3 and H3 SoCs.
652 bool "Fast Ethernet Controller on MPC8XX"
656 This driver implements support for the Fast Ethernet Controller
660 bool "Socionext AVE Ethernet support"
661 depends on DM_ETH && ARCH_UNIPHIER
666 This driver implements support for the Socionext AVE Ethernet
667 controller, as found on the Socionext UniPhier family.
669 source "drivers/net/mscc_eswitch/Kconfig"
673 depends on MPC8XX_FEC
678 depends on ETHER_ON_FEC1
681 Define to the hardcoded PHY address which corresponds
682 to the given FEC; i. e.
683 #define CONFIG_FEC1_PHY 4
684 means that the PHY with address 4 is connected to FEC1
686 When set to -1, means to probe for first available.
690 depends on ETHER_ON_FEC1
693 The PHY does not have a RXERR line (RMII only).
694 (so program the FEC to ignore it).
698 depends on MPC8XX_FEC && MPC885
703 depends on ETHER_ON_FEC2
706 Define to the hardcoded PHY address which corresponds
707 to the given FEC; i. e.
708 #define CONFIG_FEC1_PHY 4
709 means that the PHY with address 4 is connected to FEC1
711 When set to -1, means to probe for first available.
713 config FEC2_PHY_NORXERR
715 depends on ETHER_ON_FEC2
718 The PHY does not have a RXERR line (RMII only).
719 (so program the FEC to ignore it).
721 config SYS_DPAA_QBMAN
722 bool "Device tree fixup for QBMan on freescale SOCs"
723 depends on (ARM || PPC) && !SPL_BUILD
724 default y if ARCH_B4860 || \
741 QBman fixups to allow deep sleep in DPAA 1 SOCs
745 bool "Enable Three-Speed Ethernet Controller"
747 This driver implements support for the (Enhanced) Three-Speed
748 Ethernet Controller found on Freescale SoCs.
751 bool "MediaTek Ethernet GMAC Driver"
757 This Driver support MediaTek Ethernet GMAC
758 Say Y to enable support for the MediaTek Ethernet GMAC.
760 config HIGMACV300_ETH
761 bool "HiSilicon Gigabit Ethernet Controller"
766 This driver supports HIGMACV300 Ethernet controller found on
770 bool "NXP ENETC Ethernet controller"
771 depends on DM_PCI && DM_ETH && DM_MDIO
773 This driver supports the NXP ENETC Ethernet controller found on some
776 config MDIO_MUX_I2CREG
777 bool "MDIO MUX accessed as a register over I2C"
778 depends on DM_MDIO_MUX && DM_I2C
780 This driver is used for MDIO muxes driven by writing to a register of
781 an I2C chip. The board it was developed for uses a mux controlled by
782 on-board FPGA which in turn is accessed as a chip over I2C.
785 bool "Qualcomm IPQ4019 MDIO interface support"
788 This driver supports the MDIO interface found in Qualcomm
789 IPQ40xx series Soc-s.
792 bool "Marvell MDIO interface support"
795 This driver supports the MDIO interface found in the network
796 interface units of the Marvell EBU SoCs (Kirkwood, Orion5x,
797 Dove, Armada 370, Armada XP, Armada 37xx and Armada7K/8K/8KP).
799 This driver is used by the MVPP2 and MVNETA drivers.
802 bool "NXP Layerscape MDIO interface support"
805 This driver supports the MDIO bus found on the Fman 10G Ethernet MACs and
806 on the mEMAC (which supports both Clauses 22 and 45).
808 config MDIO_MUX_MMIOREG
809 bool "MDIO MUX accessed as a MMIO register access"
810 depends on DM_MDIO_MUX
812 This driver is used for MDIO muxes driven by writing to a register in
813 the MMIO physical memory.
815 config MDIO_MUX_MESON_G12A
816 bool "MDIO MUX for Amlogic Meson G12A SoCs"
817 depends on DM_MDIO_MUX
819 This driver is used for the MDIO mux found on the Amlogic G12A & compatible