drivers/mmc/host/dw_mmc.c

   1 /*
   2  * Synopsys DesignWare Multimedia Card Interface driver
   3  *  (Based on NXP driver for lpc 31xx)
   4  *
   5  * Copyright (C) 2009 NXP Semiconductors
   6  * Copyright (C) 2009, 2010 Imagination Technologies Ltd.
   7  *
   8  * This program is free software; you can redistribute it and/or modify
   9  * it under the terms of the GNU General Public License as published by
  10  * the Free Software Foundation; either version 2 of the License, or
  11  * (at your option) any later version.
  12  */
  13
  14 #include <linux/blkdev.h>
  15 #include <linux/clk.h>
  16 #include <linux/debugfs.h>
  17 #include <linux/device.h>
  18 #include <linux/dma-mapping.h>
  19 #include <linux/err.h>
  20 #include <linux/init.h>
  21 #include <linux/interrupt.h>
  22 #include <linux/iopoll.h>
  23 #include <linux/ioport.h>
  24 #include <linux/module.h>
  25 #include <linux/platform_device.h>
  26 #include <linux/pm_runtime.h>
  27 #include <linux/seq_file.h>
  28 #include <linux/slab.h>
  29 #include <linux/stat.h>
  30 #include <linux/delay.h>
  31 #include <linux/irq.h>
  32 #include <linux/mmc/card.h>
  33 #include <linux/mmc/host.h>
  34 #include <linux/mmc/mmc.h>
  35 #include <linux/mmc/sd.h>
  36 #include <linux/mmc/sdio.h>
  37 #include <linux/bitops.h>
  38 #include <linux/regulator/consumer.h>
  39 #include <linux/of.h>
  40 #include <linux/of_gpio.h>
  41 #include <linux/mmc/slot-gpio.h>
  42
  43 #include "dw_mmc.h"
  44
  45 /* Common flag combinations */
  46 #define DW_MCI_DATA_ERROR_FLAGS (SDMMC_INT_DRTO | SDMMC_INT_DCRC | \
  47                                  SDMMC_INT_HTO | SDMMC_INT_SBE  | \
  48                                  SDMMC_INT_EBE | SDMMC_INT_HLE)
  49 #define DW_MCI_CMD_ERROR_FLAGS  (SDMMC_INT_RTO | SDMMC_INT_RCRC | \
  50                                  SDMMC_INT_RESP_ERR | SDMMC_INT_HLE)
  51 #define DW_MCI_ERROR_FLAGS      (DW_MCI_DATA_ERROR_FLAGS | \
  52                                  DW_MCI_CMD_ERROR_FLAGS)
  53 #define DW_MCI_SEND_STATUS      1
  54 #define DW_MCI_RECV_STATUS      2
  55 #define DW_MCI_DMA_THRESHOLD    16
  56
  57 #define DW_MCI_FREQ_MAX 200000000       /* unit: HZ */
  58 #define DW_MCI_FREQ_MIN 100000          /* unit: HZ */
  59
  60 #define IDMAC_INT_CLR           (SDMMC_IDMAC_INT_AI | SDMMC_IDMAC_INT_NI | \
  61                                  SDMMC_IDMAC_INT_CES | SDMMC_IDMAC_INT_DU | \
  62                                  SDMMC_IDMAC_INT_FBE | SDMMC_IDMAC_INT_RI | \
  63                                  SDMMC_IDMAC_INT_TI)
  64
  65 #define DESC_RING_BUF_SZ        PAGE_SIZE
  66
  67 struct idmac_desc_64addr {
  68         u32             des0;   /* Control Descriptor */
  69 #define IDMAC_OWN_CLR64(x) \
  70         !((x) & cpu_to_le32(IDMAC_DES0_OWN))
  71
  72         u32             des1;   /* Reserved */
  73
  74         u32             des2;   /*Buffer sizes */
  75 #define IDMAC_64ADDR_SET_BUFFER1_SIZE(d, s) \
  76         ((d)->des2 = ((d)->des2 & cpu_to_le32(0x03ffe000)) | \
  77          ((cpu_to_le32(s)) & cpu_to_le32(0x1fff)))
  78
  79         u32             des3;   /* Reserved */
  80
  81         u32             des4;   /* Lower 32-bits of Buffer Address Pointer 1*/
  82         u32             des5;   /* Upper 32-bits of Buffer Address Pointer 1*/
  83
  84         u32             des6;   /* Lower 32-bits of Next Descriptor Address */
  85         u32             des7;   /* Upper 32-bits of Next Descriptor Address */
  86 };
  87
  88 struct idmac_desc {
  89         __le32          des0;   /* Control Descriptor */
  90 #define IDMAC_DES0_DIC  BIT(1)
  91 #define IDMAC_DES0_LD   BIT(2)
  92 #define IDMAC_DES0_FD   BIT(3)
  93 #define IDMAC_DES0_CH   BIT(4)
  94 #define IDMAC_DES0_ER   BIT(5)
  95 #define IDMAC_DES0_CES  BIT(30)
  96 #define IDMAC_DES0_OWN  BIT(31)
  97
  98         __le32          des1;   /* Buffer sizes */
  99 #define IDMAC_SET_BUFFER1_SIZE(d, s) \
 100         ((d)->des1 = ((d)->des1 & cpu_to_le32(0x03ffe000)) | (cpu_to_le32((s) & 0x1fff)))
 101
 102         __le32          des2;   /* buffer 1 physical address */
 103
 104         __le32          des3;   /* buffer 2 physical address */
 105 };
 106
 107 /* Each descriptor can transfer up to 4KB of data in chained mode */
 108 #define DW_MCI_DESC_DATA_LENGTH 0x1000
 109
 110 #if defined(CONFIG_DEBUG_FS)
 111 static int dw_mci_req_show(struct seq_file *s, void *v)
 112 {
 113         struct dw_mci_slot *slot = s->private;
 114         struct mmc_request *mrq;
 115         struct mmc_command *cmd;
 116         struct mmc_command *stop;
 117         struct mmc_data *data;
 118
 119         /* Make sure we get a consistent snapshot */
 120         spin_lock_bh(&slot->host->lock);
 121         mrq = slot->mrq;
 122
 123         if (mrq) {
 124                 cmd = mrq->cmd;
 125                 data = mrq->data;
 126                 stop = mrq->stop;
 127
 128                 if (cmd)
 129                         seq_printf(s,
 130                                    "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
 131                                    cmd->opcode, cmd->arg, cmd->flags,
 132                                    cmd->resp[0], cmd->resp[1], cmd->resp[2],
 133                                    cmd->resp[2], cmd->error);
 134                 if (data)
 135                         seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
 136                                    data->bytes_xfered, data->blocks,
 137                                    data->blksz, data->flags, data->error);
 138                 if (stop)
 139                         seq_printf(s,
 140                                    "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
 141                                    stop->opcode, stop->arg, stop->flags,
 142                                    stop->resp[0], stop->resp[1], stop->resp[2],
 143                                    stop->resp[2], stop->error);
 144         }
 145
 146         spin_unlock_bh(&slot->host->lock);
 147
 148         return 0;
 149 }
 150
 151 static int dw_mci_req_open(struct inode *inode, struct file *file)
 152 {
 153         return single_open(file, dw_mci_req_show, inode->i_private);
 154 }
 155
 156 static const struct file_operations dw_mci_req_fops = {
 157         .owner          = THIS_MODULE,
 158         .open           = dw_mci_req_open,
 159         .read           = seq_read,
 160         .llseek         = seq_lseek,
 161         .release        = single_release,
 162 };
 163
 164 static int dw_mci_regs_show(struct seq_file *s, void *v)
 165 {
 166         struct dw_mci *host = s->private;
 167
 168         seq_printf(s, "STATUS:\t0x%08x\n", mci_readl(host, STATUS));
 169         seq_printf(s, "RINTSTS:\t0x%08x\n", mci_readl(host, RINTSTS));
 170         seq_printf(s, "CMD:\t0x%08x\n", mci_readl(host, CMD));
 171         seq_printf(s, "CTRL:\t0x%08x\n", mci_readl(host, CTRL));
 172         seq_printf(s, "INTMASK:\t0x%08x\n", mci_readl(host, INTMASK));
 173         seq_printf(s, "CLKENA:\t0x%08x\n", mci_readl(host, CLKENA));
 174
 175         return 0;
 176 }
 177
 178 static int dw_mci_regs_open(struct inode *inode, struct file *file)
 179 {
 180         return single_open(file, dw_mci_regs_show, inode->i_private);
 181 }
 182
 183 static const struct file_operations dw_mci_regs_fops = {
 184         .owner          = THIS_MODULE,
 185         .open           = dw_mci_regs_open,
 186         .read           = seq_read,
 187         .llseek         = seq_lseek,
 188         .release        = single_release,
 189 };
 190
 191 static void dw_mci_init_debugfs(struct dw_mci_slot *slot)
 192 {
 193         struct mmc_host *mmc = slot->mmc;
 194         struct dw_mci *host = slot->host;
 195         struct dentry *root;
 196         struct dentry *node;
 197
 198         root = mmc->debugfs_root;
 199         if (!root)
 200                 return;
 201
 202         node = debugfs_create_file("regs", S_IRUSR, root, host,
 203                                    &dw_mci_regs_fops);
 204         if (!node)
 205                 goto err;
 206
 207         node = debugfs_create_file("req", S_IRUSR, root, slot,
 208                                    &dw_mci_req_fops);
 209         if (!node)
 210                 goto err;
 211
 212         node = debugfs_create_u32("state", S_IRUSR, root, (u32 *)&host->state);
 213         if (!node)
 214                 goto err;
 215
 216         node = debugfs_create_x32("pending_events", S_IRUSR, root,
 217                                   (u32 *)&host->pending_events);
 218         if (!node)
 219                 goto err;
 220
 221         node = debugfs_create_x32("completed_events", S_IRUSR, root,
 222                                   (u32 *)&host->completed_events);
 223         if (!node)
 224                 goto err;
 225
 226         return;
 227
 228 err:
 229         dev_err(&mmc->class_dev, "failed to initialize debugfs for slot\n");
 230 }
 231 #endif /* defined(CONFIG_DEBUG_FS) */
 232
 233 static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset)
 234 {
 235         u32 ctrl;
 236
 237         ctrl = mci_readl(host, CTRL);
 238         ctrl |= reset;
 239         mci_writel(host, CTRL, ctrl);
 240
 241         /* wait till resets clear */
 242         if (readl_poll_timeout_atomic(host->regs + SDMMC_CTRL, ctrl,
 243                                       !(ctrl & reset),
 244                                       1, 500 * USEC_PER_MSEC)) {
 245                 dev_err(host->dev,
 246                         "Timeout resetting block (ctrl reset %#x)\n",
 247                         ctrl & reset);
 248                 return false;
 249         }
 250
 251         return true;
 252 }
 253
 254 static void dw_mci_wait_while_busy(struct dw_mci *host, u32 cmd_flags)
 255 {
 256         u32 status;
 257
 258         /*
 259          * Databook says that before issuing a new data transfer command
 260          * we need to check to see if the card is busy.  Data transfer commands
 261          * all have SDMMC_CMD_PRV_DAT_WAIT set, so we'll key off that.
 262          *
 263          * ...also allow sending for SDMMC_CMD_VOLT_SWITCH where busy is
 264          * expected.
 265          */
 266         if ((cmd_flags & SDMMC_CMD_PRV_DAT_WAIT) &&
 267             !(cmd_flags & SDMMC_CMD_VOLT_SWITCH)) {
 268                 if (readl_poll_timeout_atomic(host->regs + SDMMC_STATUS,
 269                                               status,
 270                                               !(status & SDMMC_STATUS_BUSY),
 271                                               10, 500 * USEC_PER_MSEC))
 272                         dev_err(host->dev, "Busy; trying anyway\n");
 273         }
 274 }
 275
 276 static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg)
 277 {
 278         struct dw_mci *host = slot->host;
 279         unsigned int cmd_status = 0;
 280
 281         mci_writel(host, CMDARG, arg);
 282         wmb(); /* drain writebuffer */
 283         dw_mci_wait_while_busy(host, cmd);
 284         mci_writel(host, CMD, SDMMC_CMD_START | cmd);
 285
 286         if (readl_poll_timeout_atomic(host->regs + SDMMC_CMD, cmd_status,
 287                                       !(cmd_status & SDMMC_CMD_START),
 288                                       1, 500 * USEC_PER_MSEC))
 289                 dev_err(&slot->mmc->class_dev,
 290                         "Timeout sending command (cmd %#x arg %#x status %#x)\n",
 291                         cmd, arg, cmd_status);
 292 }
 293
 294 static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
 295 {
 296         struct dw_mci_slot *slot = mmc_priv(mmc);
 297         struct dw_mci *host = slot->host;
 298         u32 cmdr;
 299
 300         cmd->error = -EINPROGRESS;
 301         cmdr = cmd->opcode;
 302
 303         if (cmd->opcode == MMC_STOP_TRANSMISSION ||
 304             cmd->opcode == MMC_GO_IDLE_STATE ||
 305             cmd->opcode == MMC_GO_INACTIVE_STATE ||
 306             (cmd->opcode == SD_IO_RW_DIRECT &&
 307              ((cmd->arg >> 9) & 0x1FFFF) == SDIO_CCCR_ABORT))
 308                 cmdr |= SDMMC_CMD_STOP;
 309         else if (cmd->opcode != MMC_SEND_STATUS && cmd->data)
 310                 cmdr |= SDMMC_CMD_PRV_DAT_WAIT;
 311
 312         if (cmd->opcode == SD_SWITCH_VOLTAGE) {
 313                 u32 clk_en_a;
 314
 315                 /* Special bit makes CMD11 not die */
 316                 cmdr |= SDMMC_CMD_VOLT_SWITCH;
 317
 318                 /* Change state to continue to handle CMD11 weirdness */
 319                 WARN_ON(slot->host->state != STATE_SENDING_CMD);
 320                 slot->host->state = STATE_SENDING_CMD11;
 321
 322                 /*
 323                  * We need to disable low power mode (automatic clock stop)
 324                  * while doing voltage switch so we don't confuse the card,
 325                  * since stopping the clock is a specific part of the UHS
 326                  * voltage change dance.
 327                  *
 328                  * Note that low power mode (SDMMC_CLKEN_LOW_PWR) will be
 329                  * unconditionally turned back on in dw_mci_setup_bus() if it's
 330                  * ever called with a non-zero clock.  That shouldn't happen
 331                  * until the voltage change is all done.
 332                  */
 333                 clk_en_a = mci_readl(host, CLKENA);
 334                 clk_en_a &= ~(SDMMC_CLKEN_LOW_PWR << slot->id);
 335                 mci_writel(host, CLKENA, clk_en_a);
 336                 mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
 337                              SDMMC_CMD_PRV_DAT_WAIT, 0);
 338         }
 339
 340         if (cmd->flags & MMC_RSP_PRESENT) {
 341                 /* We expect a response, so set this bit */
 342                 cmdr |= SDMMC_CMD_RESP_EXP;
 343                 if (cmd->flags & MMC_RSP_136)
 344                         cmdr |= SDMMC_CMD_RESP_LONG;
 345         }
 346
 347         if (cmd->flags & MMC_RSP_CRC)
 348                 cmdr |= SDMMC_CMD_RESP_CRC;
 349
 350         if (cmd->data) {
 351                 cmdr |= SDMMC_CMD_DAT_EXP;
 352                 if (cmd->data->flags & MMC_DATA_WRITE)
 353                         cmdr |= SDMMC_CMD_DAT_WR;
 354         }
 355
 356         if (!test_bit(DW_MMC_CARD_NO_USE_HOLD, &slot->flags))
 357                 cmdr |= SDMMC_CMD_USE_HOLD_REG;
 358
 359         return cmdr;
 360 }
 361
 362 static u32 dw_mci_prep_stop_abort(struct dw_mci *host, struct mmc_command *cmd)
 363 {
 364         struct mmc_command *stop;
 365         u32 cmdr;
 366
 367         if (!cmd->data)
 368                 return 0;
 369
 370         stop = &host->stop_abort;
 371         cmdr = cmd->opcode;
 372         memset(stop, 0, sizeof(struct mmc_command));
 373
 374         if (cmdr == MMC_READ_SINGLE_BLOCK ||
 375             cmdr == MMC_READ_MULTIPLE_BLOCK ||
 376             cmdr == MMC_WRITE_BLOCK ||
 377             cmdr == MMC_WRITE_MULTIPLE_BLOCK ||
 378             cmdr == MMC_SEND_TUNING_BLOCK ||
 379             cmdr == MMC_SEND_TUNING_BLOCK_HS200) {
 380                 stop->opcode = MMC_STOP_TRANSMISSION;
 381                 stop->arg = 0;
 382                 stop->flags = MMC_RSP_R1B | MMC_CMD_AC;
 383         } else if (cmdr == SD_IO_RW_EXTENDED) {
 384                 stop->opcode = SD_IO_RW_DIRECT;
 385                 stop->arg |= (1 << 31) | (0 << 28) | (SDIO_CCCR_ABORT << 9) |
 386                              ((cmd->arg >> 28) & 0x7);
 387                 stop->flags = MMC_RSP_SPI_R5 | MMC_RSP_R5 | MMC_CMD_AC;
 388         } else {
 389                 return 0;
 390         }
 391
 392         cmdr = stop->opcode | SDMMC_CMD_STOP |
 393                 SDMMC_CMD_RESP_CRC | SDMMC_CMD_RESP_EXP;
 394
 395         if (!test_bit(DW_MMC_CARD_NO_USE_HOLD, &host->cur_slot->flags))
 396                 cmdr |= SDMMC_CMD_USE_HOLD_REG;
 397
 398         return cmdr;
 399 }
 400
 401 static void dw_mci_start_command(struct dw_mci *host,
 402                                  struct mmc_command *cmd, u32 cmd_flags)
 403 {
 404         host->cmd = cmd;
 405         dev_vdbg(host->dev,
 406                  "start command: ARGR=0x%08x CMDR=0x%08x\n",
 407                  cmd->arg, cmd_flags);
 408
 409         mci_writel(host, CMDARG, cmd->arg);
 410         wmb(); /* drain writebuffer */
 411         dw_mci_wait_while_busy(host, cmd_flags);
 412
 413         mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
 414 }
 415
 416 static inline void send_stop_abort(struct dw_mci *host, struct mmc_data *data)
 417 {
 418         struct mmc_command *stop = &host->stop_abort;
 419
 420         dw_mci_start_command(host, stop, host->stop_cmdr);
 421 }
 422
 423 /* DMA interface functions */
 424 static void dw_mci_stop_dma(struct dw_mci *host)
 425 {
 426         if (host->using_dma) {
 427                 host->dma_ops->stop(host);
 428                 host->dma_ops->cleanup(host);
 429         }
 430
 431         /* Data transfer was stopped by the interrupt handler */
 432         set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
 433 }
 434
 435 static void dw_mci_dma_cleanup(struct dw_mci *host)
 436 {
 437         struct mmc_data *data = host->data;
 438
 439         if (data && data->host_cookie == COOKIE_MAPPED) {
 440                 dma_unmap_sg(host->dev,
 441                              data->sg,
 442                              data->sg_len,
 443                              mmc_get_dma_dir(data));
 444                 data->host_cookie = COOKIE_UNMAPPED;
 445         }
 446 }
 447
 448 static void dw_mci_idmac_reset(struct dw_mci *host)
 449 {
 450         u32 bmod = mci_readl(host, BMOD);
 451         /* Software reset of DMA */
 452         bmod |= SDMMC_IDMAC_SWRESET;
 453         mci_writel(host, BMOD, bmod);
 454 }
 455
 456 static void dw_mci_idmac_stop_dma(struct dw_mci *host)
 457 {
 458         u32 temp;
 459
 460         /* Disable and reset the IDMAC interface */
 461         temp = mci_readl(host, CTRL);
 462         temp &= ~SDMMC_CTRL_USE_IDMAC;
 463         temp |= SDMMC_CTRL_DMA_RESET;
 464         mci_writel(host, CTRL, temp);
 465
 466         /* Stop the IDMAC running */
 467         temp = mci_readl(host, BMOD);
 468         temp &= ~(SDMMC_IDMAC_ENABLE | SDMMC_IDMAC_FB);
 469         temp |= SDMMC_IDMAC_SWRESET;
 470         mci_writel(host, BMOD, temp);
 471 }
 472
 473 static void dw_mci_dmac_complete_dma(void *arg)
 474 {
 475         struct dw_mci *host = arg;
 476         struct mmc_data *data = host->data;
 477
 478         dev_vdbg(host->dev, "DMA complete\n");
 479
 480         if ((host->use_dma == TRANS_MODE_EDMAC) &&
 481             data && (data->flags & MMC_DATA_READ))
 482                 /* Invalidate cache after read */
 483                 dma_sync_sg_for_cpu(mmc_dev(host->cur_slot->mmc),
 484                                     data->sg,
 485                                     data->sg_len,
 486                                     DMA_FROM_DEVICE);
 487
 488         host->dma_ops->cleanup(host);
 489
 490         /*
 491          * If the card was removed, data will be NULL. No point in trying to
 492          * send the stop command or waiting for NBUSY in this case.
 493          */
 494         if (data) {
 495                 set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
 496                 tasklet_schedule(&host->tasklet);
 497         }
 498 }
 499
 500 static int dw_mci_idmac_init(struct dw_mci *host)
 501 {
 502         int i;
 503
 504         if (host->dma_64bit_address == 1) {
 505                 struct idmac_desc_64addr *p;
 506                 /* Number of descriptors in the ring buffer */
 507                 host->ring_size =
 508                         DESC_RING_BUF_SZ / sizeof(struct idmac_desc_64addr);
 509
 510                 /* Forward link the descriptor list */
 511                 for (i = 0, p = host->sg_cpu; i < host->ring_size - 1;
 512                                                                 i++, p++) {
 513                         p->des6 = (host->sg_dma +
 514                                         (sizeof(struct idmac_desc_64addr) *
 515                                                         (i + 1))) & 0xffffffff;
 516
 517                         p->des7 = (u64)(host->sg_dma +
 518                                         (sizeof(struct idmac_desc_64addr) *
 519                                                         (i + 1))) >> 32;
 520                         /* Initialize reserved and buffer size fields to "0" */
 521                         p->des1 = 0;
 522                         p->des2 = 0;
 523                         p->des3 = 0;
 524                 }
 525
 526                 /* Set the last descriptor as the end-of-ring descriptor */
 527                 p->des6 = host->sg_dma & 0xffffffff;
 528                 p->des7 = (u64)host->sg_dma >> 32;
 529                 p->des0 = IDMAC_DES0_ER;
 530
 531         } else {
 532                 struct idmac_desc *p;
 533                 /* Number of descriptors in the ring buffer */
 534                 host->ring_size =
 535                         DESC_RING_BUF_SZ / sizeof(struct idmac_desc);
 536
 537                 /* Forward link the descriptor list */
 538                 for (i = 0, p = host->sg_cpu;
 539                      i < host->ring_size - 1;
 540                      i++, p++) {
 541                         p->des3 = cpu_to_le32(host->sg_dma +
 542                                         (sizeof(struct idmac_desc) * (i + 1)));
 543                         p->des1 = 0;
 544                 }
 545
 546                 /* Set the last descriptor as the end-of-ring descriptor */
 547                 p->des3 = cpu_to_le32(host->sg_dma);
 548                 p->des0 = cpu_to_le32(IDMAC_DES0_ER);
 549         }
 550
 551         dw_mci_idmac_reset(host);
 552
 553         if (host->dma_64bit_address == 1) {
 554                 /* Mask out interrupts - get Tx & Rx complete only */
 555                 mci_writel(host, IDSTS64, IDMAC_INT_CLR);
 556                 mci_writel(host, IDINTEN64, SDMMC_IDMAC_INT_NI |
 557                                 SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
 558
 559                 /* Set the descriptor base address */
 560                 mci_writel(host, DBADDRL, host->sg_dma & 0xffffffff);
 561                 mci_writel(host, DBADDRU, (u64)host->sg_dma >> 32);
 562
 563         } else {
 564                 /* Mask out interrupts - get Tx & Rx complete only */
 565                 mci_writel(host, IDSTS, IDMAC_INT_CLR);
 566                 mci_writel(host, IDINTEN, SDMMC_IDMAC_INT_NI |
 567                                 SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
 568
 569                 /* Set the descriptor base address */
 570                 mci_writel(host, DBADDR, host->sg_dma);
 571         }
 572
 573         return 0;
 574 }
 575
 576 static inline int dw_mci_prepare_desc64(struct dw_mci *host,
 577                                          struct mmc_data *data,
 578                                          unsigned int sg_len)
 579 {
 580         unsigned int desc_len;
 581         struct idmac_desc_64addr *desc_first, *desc_last, *desc;
 582         u32 val;
 583         int i;
 584
 585         desc_first = desc_last = desc = host->sg_cpu;
 586
 587         for (i = 0; i < sg_len; i++) {
 588                 unsigned int length = sg_dma_len(&data->sg[i]);
 589
 590                 u64 mem_addr = sg_dma_address(&data->sg[i]);
 591
 592                 for ( ; length ; desc++) {
 593                         desc_len = (length <= DW_MCI_DESC_DATA_LENGTH) ?
 594                                    length : DW_MCI_DESC_DATA_LENGTH;
 595
 596                         length -= desc_len;
 597
 598                         /*
 599                          * Wait for the former clear OWN bit operation
 600                          * of IDMAC to make sure that this descriptor
 601                          * isn't still owned by IDMAC as IDMAC's write
 602                          * ops and CPU's read ops are asynchronous.
 603                          */
 604                         if (readl_poll_timeout_atomic(&desc->des0, val,
 605                                                 !(val & IDMAC_DES0_OWN),
 606                                                 10, 100 * USEC_PER_MSEC))
 607                                 goto err_own_bit;
 608
 609                         /*
 610                          * Set the OWN bit and disable interrupts
 611                          * for this descriptor
 612                          */
 613                         desc->des0 = IDMAC_DES0_OWN | IDMAC_DES0_DIC |
 614                                                 IDMAC_DES0_CH;
 615
 616                         /* Buffer length */
 617                         IDMAC_64ADDR_SET_BUFFER1_SIZE(desc, desc_len);
 618
 619                         /* Physical address to DMA to/from */
 620                         desc->des4 = mem_addr & 0xffffffff;
 621                         desc->des5 = mem_addr >> 32;
 622
 623                         /* Update physical address for the next desc */
 624                         mem_addr += desc_len;
 625
 626                         /* Save pointer to the last descriptor */
 627                         desc_last = desc;
 628                 }
 629         }
 630
 631         /* Set first descriptor */
 632         desc_first->des0 |= IDMAC_DES0_FD;
 633
 634         /* Set last descriptor */
 635         desc_last->des0 &= ~(IDMAC_DES0_CH | IDMAC_DES0_DIC);
 636         desc_last->des0 |= IDMAC_DES0_LD;
 637
 638         return 0;
 639 err_own_bit:
 640         /* restore the descriptor chain as it's polluted */
 641         dev_dbg(host->dev, "descriptor is still owned by IDMAC.\n");
 642         memset(host->sg_cpu, 0, DESC_RING_BUF_SZ);
 643         dw_mci_idmac_init(host);
 644         return -EINVAL;
 645 }
 646
 647
 648 static inline int dw_mci_prepare_desc32(struct dw_mci *host,
 649                                          struct mmc_data *data,
 650                                          unsigned int sg_len)
 651 {
 652         unsigned int desc_len;
 653         struct idmac_desc *desc_first, *desc_last, *desc;
 654         u32 val;
 655         int i;
 656
 657         desc_first = desc_last = desc = host->sg_cpu;
 658
 659         for (i = 0; i < sg_len; i++) {
 660                 unsigned int length = sg_dma_len(&data->sg[i]);
 661
 662                 u32 mem_addr = sg_dma_address(&data->sg[i]);
 663
 664                 for ( ; length ; desc++) {
 665                         desc_len = (length <= DW_MCI_DESC_DATA_LENGTH) ?
 666                                    length : DW_MCI_DESC_DATA_LENGTH;
 667
 668                         length -= desc_len;
 669
 670                         /*
 671                          * Wait for the former clear OWN bit operation
 672                          * of IDMAC to make sure that this descriptor
 673                          * isn't still owned by IDMAC as IDMAC's write
 674                          * ops and CPU's read ops are asynchronous.
 675                          */
 676                         if (readl_poll_timeout_atomic(&desc->des0, val,
 677                                                       IDMAC_OWN_CLR64(val),
 678                                                       10,
 679                                                       100 * USEC_PER_MSEC))
 680                                 goto err_own_bit;
 681
 682                         /*
 683                          * Set the OWN bit and disable interrupts
 684                          * for this descriptor
 685                          */
 686                         desc->des0 = cpu_to_le32(IDMAC_DES0_OWN |
 687                                                  IDMAC_DES0_DIC |
 688                                                  IDMAC_DES0_CH);
 689
 690                         /* Buffer length */
 691                         IDMAC_SET_BUFFER1_SIZE(desc, desc_len);
 692
 693                         /* Physical address to DMA to/from */
 694                         desc->des2 = cpu_to_le32(mem_addr);
 695
 696                         /* Update physical address for the next desc */
 697                         mem_addr += desc_len;
 698
 699                         /* Save pointer to the last descriptor */
 700                         desc_last = desc;
 701                 }
 702         }
 703
 704         /* Set first descriptor */
 705         desc_first->des0 |= cpu_to_le32(IDMAC_DES0_FD);
 706
 707         /* Set last descriptor */
 708         desc_last->des0 &= cpu_to_le32(~(IDMAC_DES0_CH |
 709                                        IDMAC_DES0_DIC));
 710         desc_last->des0 |= cpu_to_le32(IDMAC_DES0_LD);
 711
 712         return 0;
 713 err_own_bit:
 714         /* restore the descriptor chain as it's polluted */
 715         dev_dbg(host->dev, "descriptor is still owned by IDMAC.\n");
 716         memset(host->sg_cpu, 0, DESC_RING_BUF_SZ);
 717         dw_mci_idmac_init(host);
 718         return -EINVAL;
 719 }
 720
 721 static int dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len)
 722 {
 723         u32 temp;
 724         int ret;
 725
 726         if (host->dma_64bit_address == 1)
 727                 ret = dw_mci_prepare_desc64(host, host->data, sg_len);
 728         else
 729                 ret = dw_mci_prepare_desc32(host, host->data, sg_len);
 730
 731         if (ret)
 732                 goto out;
 733
 734         /* drain writebuffer */
 735         wmb();
 736
 737         /* Make sure to reset DMA in case we did PIO before this */
 738         dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET);
 739         dw_mci_idmac_reset(host);
 740
 741         /* Select IDMAC interface */
 742         temp = mci_readl(host, CTRL);
 743         temp |= SDMMC_CTRL_USE_IDMAC;
 744         mci_writel(host, CTRL, temp);
 745
 746         /* drain writebuffer */
 747         wmb();
 748
 749         /* Enable the IDMAC */
 750         temp = mci_readl(host, BMOD);
 751         temp |= SDMMC_IDMAC_ENABLE | SDMMC_IDMAC_FB;
 752         mci_writel(host, BMOD, temp);
 753
 754         /* Start it running */
 755         mci_writel(host, PLDMND, 1);
 756
 757 out:
 758         return ret;
 759 }
 760
 761 static const struct dw_mci_dma_ops dw_mci_idmac_ops = {
 762         .init = dw_mci_idmac_init,
 763         .start = dw_mci_idmac_start_dma,
 764         .stop = dw_mci_idmac_stop_dma,
 765         .complete = dw_mci_dmac_complete_dma,
 766         .cleanup = dw_mci_dma_cleanup,
 767 };
 768
 769 static void dw_mci_edmac_stop_dma(struct dw_mci *host)
 770 {
 771         dmaengine_terminate_async(host->dms->ch);
 772 }
 773
 774 static int dw_mci_edmac_start_dma(struct dw_mci *host,
 775                                             unsigned int sg_len)
 776 {
 777         struct dma_slave_config cfg;
 778         struct dma_async_tx_descriptor *desc = NULL;
 779         struct scatterlist *sgl = host->data->sg;
 780         const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
 781         u32 sg_elems = host->data->sg_len;
 782         u32 fifoth_val;
 783         u32 fifo_offset = host->fifo_reg - host->regs;
 784         int ret = 0;
 785
 786         /* Set external dma config: burst size, burst width */
 787         cfg.dst_addr = host->phy_regs + fifo_offset;
 788         cfg.src_addr = cfg.dst_addr;
 789         cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
 790         cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
 791
 792         /* Match burst msize with external dma config */
 793         fifoth_val = mci_readl(host, FIFOTH);
 794         cfg.dst_maxburst = mszs[(fifoth_val >> 28) & 0x7];
 795         cfg.src_maxburst = cfg.dst_maxburst;
 796
 797         if (host->data->flags & MMC_DATA_WRITE)
 798                 cfg.direction = DMA_MEM_TO_DEV;
 799         else
 800                 cfg.direction = DMA_DEV_TO_MEM;
 801
 802         ret = dmaengine_slave_config(host->dms->ch, &cfg);
 803         if (ret) {
 804                 dev_err(host->dev, "Failed to config edmac.\n");
 805                 return -EBUSY;
 806         }
 807
 808         desc = dmaengine_prep_slave_sg(host->dms->ch, sgl,
 809                                        sg_len, cfg.direction,
 810                                        DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 811         if (!desc) {
 812                 dev_err(host->dev, "Can't prepare slave sg.\n");
 813                 return -EBUSY;
 814         }
 815
 816         /* Set dw_mci_dmac_complete_dma as callback */
 817         desc->callback = dw_mci_dmac_complete_dma;
 818         desc->callback_param = (void *)host;
 819         dmaengine_submit(desc);
 820
 821         /* Flush cache before write */
 822         if (host->data->flags & MMC_DATA_WRITE)
 823                 dma_sync_sg_for_device(mmc_dev(host->cur_slot->mmc), sgl,
 824                                        sg_elems, DMA_TO_DEVICE);
 825
 826         dma_async_issue_pending(host->dms->ch);
 827
 828         return 0;
 829 }
 830
 831 static int dw_mci_edmac_init(struct dw_mci *host)
 832 {
 833         /* Request external dma channel */
 834         host->dms = kzalloc(sizeof(struct dw_mci_dma_slave), GFP_KERNEL);
 835         if (!host->dms)
 836                 return -ENOMEM;
 837
 838         host->dms->ch = dma_request_slave_channel(host->dev, "rx-tx");
 839         if (!host->dms->ch) {
 840                 dev_err(host->dev, "Failed to get external DMA channel.\n");
 841                 kfree(host->dms);
 842                 host->dms = NULL;
 843                 return -ENXIO;
 844         }
 845
 846         return 0;
 847 }
 848
 849 static void dw_mci_edmac_exit(struct dw_mci *host)
 850 {
 851         if (host->dms) {
 852                 if (host->dms->ch) {
 853                         dma_release_channel(host->dms->ch);
 854                         host->dms->ch = NULL;
 855                 }
 856                 kfree(host->dms);
 857                 host->dms = NULL;
 858         }
 859 }
 860
 861 static const struct dw_mci_dma_ops dw_mci_edmac_ops = {
 862         .init = dw_mci_edmac_init,
 863         .exit = dw_mci_edmac_exit,
 864         .start = dw_mci_edmac_start_dma,
 865         .stop = dw_mci_edmac_stop_dma,
 866         .complete = dw_mci_dmac_complete_dma,
 867         .cleanup = dw_mci_dma_cleanup,
 868 };
 869
 870 static int dw_mci_pre_dma_transfer(struct dw_mci *host,
 871                                    struct mmc_data *data,
 872                                    int cookie)
 873 {
 874         struct scatterlist *sg;
 875         unsigned int i, sg_len;
 876
 877         if (data->host_cookie == COOKIE_PRE_MAPPED)
 878                 return data->sg_len;
 879
 880         /*
 881          * We don't do DMA on "complex" transfers, i.e. with
 882          * non-word-aligned buffers or lengths. Also, we don't bother
 883          * with all the DMA setup overhead for short transfers.
 884          */
 885         if (data->blocks * data->blksz < DW_MCI_DMA_THRESHOLD)
 886                 return -EINVAL;
 887
 888         if (data->blksz & 3)
 889                 return -EINVAL;
 890
 891         for_each_sg(data->sg, sg, data->sg_len, i) {
 892                 if (sg->offset & 3 || sg->length & 3)
 893                         return -EINVAL;
 894         }
 895
 896         sg_len = dma_map_sg(host->dev,
 897                             data->sg,
 898                             data->sg_len,
 899                             mmc_get_dma_dir(data));
 900         if (sg_len == 0)
 901                 return -EINVAL;
 902
 903         data->host_cookie = cookie;
 904
 905         return sg_len;
 906 }
 907
 908 static void dw_mci_pre_req(struct mmc_host *mmc,
 909                            struct mmc_request *mrq)
 910 {
 911         struct dw_mci_slot *slot = mmc_priv(mmc);
 912         struct mmc_data *data = mrq->data;
 913
 914         if (!slot->host->use_dma || !data)
 915                 return;
 916
 917         /* This data might be unmapped at this time */
 918         data->host_cookie = COOKIE_UNMAPPED;
 919
 920         if (dw_mci_pre_dma_transfer(slot->host, mrq->data,
 921                                 COOKIE_PRE_MAPPED) < 0)
 922                 data->host_cookie = COOKIE_UNMAPPED;
 923 }
 924
 925 static void dw_mci_post_req(struct mmc_host *mmc,
 926                             struct mmc_request *mrq,
 927                             int err)
 928 {
 929         struct dw_mci_slot *slot = mmc_priv(mmc);
 930         struct mmc_data *data = mrq->data;
 931
 932         if (!slot->host->use_dma || !data)
 933                 return;
 934
 935         if (data->host_cookie != COOKIE_UNMAPPED)
 936                 dma_unmap_sg(slot->host->dev,
 937                              data->sg,
 938                              data->sg_len,
 939                              mmc_get_dma_dir(data));
 940         data->host_cookie = COOKIE_UNMAPPED;
 941 }
 942
 943 static int dw_mci_get_cd(struct mmc_host *mmc)
 944 {
 945         int present;
 946         struct dw_mci_slot *slot = mmc_priv(mmc);
 947         struct dw_mci *host = slot->host;
 948         int gpio_cd = mmc_gpio_get_cd(mmc);
 949
 950         /* Use platform get_cd function, else try onboard card detect */
 951         if (((mmc->caps & MMC_CAP_NEEDS_POLL)
 952                                 || !mmc_card_is_removable(mmc))) {
 953                 present = 1;
 954
 955                 if (!test_bit(DW_MMC_CARD_PRESENT, &slot->flags)) {
 956                         if (mmc->caps & MMC_CAP_NEEDS_POLL) {
 957                                 dev_info(&mmc->class_dev,
 958                                         "card is polling.\n");
 959                         } else {
 960                                 dev_info(&mmc->class_dev,
 961                                         "card is non-removable.\n");
 962                         }
 963                         set_bit(DW_MMC_CARD_PRESENT, &slot->flags);
 964                 }
 965
 966                 return present;
 967         } else if (gpio_cd >= 0)
 968                 present = gpio_cd;
 969         else
 970                 present = (mci_readl(slot->host, CDETECT) & (1 << slot->id))
 971                         == 0 ? 1 : 0;
 972
 973         spin_lock_bh(&host->lock);
 974         if (present && !test_and_set_bit(DW_MMC_CARD_PRESENT, &slot->flags))
 975                 dev_dbg(&mmc->class_dev, "card is present\n");
 976         else if (!present &&
 977                         !test_and_clear_bit(DW_MMC_CARD_PRESENT, &slot->flags))
 978                 dev_dbg(&mmc->class_dev, "card is not present\n");
 979         spin_unlock_bh(&host->lock);
 980
 981         return present;
 982 }
 983
 984 static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data)
 985 {
 986         unsigned int blksz = data->blksz;
 987         const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
 988         u32 fifo_width = 1 << host->data_shift;
 989         u32 blksz_depth = blksz / fifo_width, fifoth_val;
 990         u32 msize = 0, rx_wmark = 1, tx_wmark, tx_wmark_invers;
 991         int idx = ARRAY_SIZE(mszs) - 1;
 992
 993         /* pio should ship this scenario */
 994         if (!host->use_dma)
 995                 return;
 996
 997         tx_wmark = (host->fifo_depth) / 2;
 998         tx_wmark_invers = host->fifo_depth - tx_wmark;
 999
1000         /*
1001          * MSIZE is '1',
1002          * if blksz is not a multiple of the FIFO width
1003          */
1004         if (blksz % fifo_width)
1005                 goto done;
1006
1007         do {
1008                 if (!((blksz_depth % mszs[idx]) ||
1009                      (tx_wmark_invers % mszs[idx]))) {
1010                         msize = idx;
1011                         rx_wmark = mszs[idx] - 1;
1012                         break;
1013                 }
1014         } while (--idx > 0);
1015         /*
1016          * If idx is '0', it won't be tried
1017          * Thus, initial values are uesed
1018          */
1019 done:
1020         fifoth_val = SDMMC_SET_FIFOTH(msize, rx_wmark, tx_wmark);
1021         mci_writel(host, FIFOTH, fifoth_val);
1022 }
1023
1024 static void dw_mci_ctrl_thld(struct dw_mci *host, struct mmc_data *data)
1025 {
1026         unsigned int blksz = data->blksz;
1027         u32 blksz_depth, fifo_depth;
1028         u16 thld_size;
1029         u8 enable;
1030
1031         /*
1032          * CDTHRCTL doesn't exist prior to 240A (in fact that register offset is
1033          * in the FIFO region, so we really shouldn't access it).
1034          */
1035         if (host->verid < DW_MMC_240A ||
1036                 (host->verid < DW_MMC_280A && data->flags & MMC_DATA_WRITE))
1037                 return;
1038
1039         /*
1040          * Card write Threshold is introduced since 2.80a
1041          * It's used when HS400 mode is enabled.
1042          */
1043         if (data->flags & MMC_DATA_WRITE &&
1044                 !(host->timing != MMC_TIMING_MMC_HS400))
1045                 return;
1046
1047         if (data->flags & MMC_DATA_WRITE)
1048                 enable = SDMMC_CARD_WR_THR_EN;
1049         else
1050                 enable = SDMMC_CARD_RD_THR_EN;
1051
1052         if (host->timing != MMC_TIMING_MMC_HS200 &&
1053             host->timing != MMC_TIMING_UHS_SDR104)
1054                 goto disable;
1055
1056         blksz_depth = blksz / (1 << host->data_shift);
1057         fifo_depth = host->fifo_depth;
1058
1059         if (blksz_depth > fifo_depth)
1060                 goto disable;
1061
1062         /*
1063          * If (blksz_depth) >= (fifo_depth >> 1), should be 'thld_size <= blksz'
1064          * If (blksz_depth) <  (fifo_depth >> 1), should be thld_size = blksz
1065          * Currently just choose blksz.
1066          */
1067         thld_size = blksz;
1068         mci_writel(host, CDTHRCTL, SDMMC_SET_THLD(thld_size, enable));
1069         return;
1070
1071 disable:
1072         mci_writel(host, CDTHRCTL, 0);
1073 }
1074
1075 static int dw_mci_submit_data_dma(struct dw_mci *host, struct mmc_data *data)
1076 {
1077         unsigned long irqflags;
1078         int sg_len;
1079         u32 temp;
1080
1081         host->using_dma = 0;
1082
1083         /* If we don't have a channel, we can't do DMA */
1084         if (!host->use_dma)
1085                 return -ENODEV;
1086
1087         sg_len = dw_mci_pre_dma_transfer(host, data, COOKIE_MAPPED);
1088         if (sg_len < 0) {
1089                 host->dma_ops->stop(host);
1090                 return sg_len;
1091         }
1092
1093         host->using_dma = 1;
1094
1095         if (host->use_dma == TRANS_MODE_IDMAC)
1096                 dev_vdbg(host->dev,
1097                          "sd sg_cpu: %#lx sg_dma: %#lx sg_len: %d\n",
1098                          (unsigned long)host->sg_cpu,
1099                          (unsigned long)host->sg_dma,
1100                          sg_len);
1101
1102         /*
1103          * Decide the MSIZE and RX/TX Watermark.
1104          * If current block size is same with previous size,
1105          * no need to update fifoth.
1106          */
1107         if (host->prev_blksz != data->blksz)
1108                 dw_mci_adjust_fifoth(host, data);
1109
1110         /* Enable the DMA interface */
1111         temp = mci_readl(host, CTRL);
1112         temp |= SDMMC_CTRL_DMA_ENABLE;
1113         mci_writel(host, CTRL, temp);
1114
1115         /* Disable RX/TX IRQs, let DMA handle it */
1116         spin_lock_irqsave(&host->irq_lock, irqflags);
1117         temp = mci_readl(host, INTMASK);
1118         temp  &= ~(SDMMC_INT_RXDR | SDMMC_INT_TXDR);
1119         mci_writel(host, INTMASK, temp);
1120         spin_unlock_irqrestore(&host->irq_lock, irqflags);
1121
1122         if (host->dma_ops->start(host, sg_len)) {
1123                 host->dma_ops->stop(host);
1124                 /* We can't do DMA, try PIO for this one */
1125                 dev_dbg(host->dev,
1126                         "%s: fall back to PIO mode for current transfer\n",
1127                         __func__);
1128                 return -ENODEV;
1129         }
1130
1131         return 0;
1132 }
1133
1134 static void dw_mci_submit_data(struct dw_mci *host, struct mmc_data *data)
1135 {
1136         unsigned long irqflags;
1137         int flags = SG_MITER_ATOMIC;
1138         u32 temp;
1139
1140         data->error = -EINPROGRESS;
1141
1142         WARN_ON(host->data);
1143         host->sg = NULL;
1144         host->data = data;
1145
1146         if (data->flags & MMC_DATA_READ)
1147                 host->dir_status = DW_MCI_RECV_STATUS;
1148         else
1149                 host->dir_status = DW_MCI_SEND_STATUS;
1150
1151         dw_mci_ctrl_thld(host, data);
1152
1153         if (dw_mci_submit_data_dma(host, data)) {
1154                 if (host->data->flags & MMC_DATA_READ)
1155                         flags |= SG_MITER_TO_SG;
1156                 else
1157                         flags |= SG_MITER_FROM_SG;
1158
1159                 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
1160                 host->sg = data->sg;
1161                 host->part_buf_start = 0;
1162                 host->part_buf_count = 0;
1163
1164                 mci_writel(host, RINTSTS, SDMMC_INT_TXDR | SDMMC_INT_RXDR);
1165
1166                 spin_lock_irqsave(&host->irq_lock, irqflags);
1167                 temp = mci_readl(host, INTMASK);
1168                 temp |= SDMMC_INT_TXDR | SDMMC_INT_RXDR;
1169                 mci_writel(host, INTMASK, temp);
1170                 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1171
1172                 temp = mci_readl(host, CTRL);
1173                 temp &= ~SDMMC_CTRL_DMA_ENABLE;
1174                 mci_writel(host, CTRL, temp);
1175
1176                 /*
1177                  * Use the initial fifoth_val for PIO mode. If wm_algined
1178                  * is set, we set watermark same as data size.
1179                  * If next issued data may be transfered by DMA mode,
1180                  * prev_blksz should be invalidated.
1181                  */
1182                 if (host->wm_aligned)
1183                         dw_mci_adjust_fifoth(host, data);
1184                 else
1185                         mci_writel(host, FIFOTH, host->fifoth_val);
1186                 host->prev_blksz = 0;
1187         } else {
1188                 /*
1189                  * Keep the current block size.
1190                  * It will be used to decide whether to update
1191                  * fifoth register next time.
1192                  */
1193                 host->prev_blksz = data->blksz;
1194         }
1195 }
1196
1197 static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
1198 {
1199         struct dw_mci *host = slot->host;
1200         unsigned int clock = slot->clock;
1201         u32 div;
1202         u32 clk_en_a;
1203         u32 sdmmc_cmd_bits = SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT;
1204
1205         /* We must continue to set bit 28 in CMD until the change is complete */
1206         if (host->state == STATE_WAITING_CMD11_DONE)
1207                 sdmmc_cmd_bits |= SDMMC_CMD_VOLT_SWITCH;
1208
1209         if (!clock) {
1210                 mci_writel(host, CLKENA, 0);
1211                 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1212         } else if (clock != host->current_speed || force_clkinit) {
1213                 div = host->bus_hz / clock;
1214                 if (host->bus_hz % clock && host->bus_hz > clock)
1215                         /*
1216                          * move the + 1 after the divide to prevent
1217                          * over-clocking the card.
1218                          */
1219                         div += 1;
1220
1221                 div = (host->bus_hz != clock) ? DIV_ROUND_UP(div, 2) : 0;
1222
1223                 if ((clock != slot->__clk_old &&
1224                         !test_bit(DW_MMC_CARD_NEEDS_POLL, &slot->flags)) ||
1225                         force_clkinit) {
1226                         /* Silent the verbose log if calling from PM context */
1227                         if (!force_clkinit)
1228                                 dev_info(&slot->mmc->class_dev,
1229                                          "Bus speed (slot %d) = %dHz (slot req %dHz, actual %dHZ div = %d)\n",
1230                                          slot->id, host->bus_hz, clock,
1231                                          div ? ((host->bus_hz / div) >> 1) :
1232                                          host->bus_hz, div);
1233
1234                         /*
1235                          * If card is polling, display the message only
1236                          * one time at boot time.
1237                          */
1238                         if (slot->mmc->caps & MMC_CAP_NEEDS_POLL &&
1239                                         slot->mmc->f_min == clock)
1240                                 set_bit(DW_MMC_CARD_NEEDS_POLL, &slot->flags);
1241                 }
1242
1243                 /* disable clock */
1244                 mci_writel(host, CLKENA, 0);
1245                 mci_writel(host, CLKSRC, 0);
1246
1247                 /* inform CIU */
1248                 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1249
1250                 /* set clock to desired speed */
1251                 mci_writel(host, CLKDIV, div);
1252
1253                 /* inform CIU */
1254                 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1255
1256                 /* enable clock; only low power if no SDIO */
1257                 clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
1258                 if (!test_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags))
1259                         clk_en_a |= SDMMC_CLKEN_LOW_PWR << slot->id;
1260                 mci_writel(host, CLKENA, clk_en_a);
1261
1262                 /* inform CIU */
1263                 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1264
1265                 /* keep the last clock value that was requested from core */
1266                 slot->__clk_old = clock;
1267         }
1268
1269         host->current_speed = clock;
1270
1271         /* Set the current slot bus width */
1272         mci_writel(host, CTYPE, (slot->ctype << slot->id));
1273 }
1274
1275 static void __dw_mci_start_request(struct dw_mci *host,
1276                                    struct dw_mci_slot *slot,
1277                                    struct mmc_command *cmd)
1278 {
1279         struct mmc_request *mrq;
1280         struct mmc_data *data;
1281         u32 cmdflags;
1282
1283         mrq = slot->mrq;
1284
1285         host->cur_slot = slot;
1286         host->mrq = mrq;
1287
1288         host->pending_events = 0;
1289         host->completed_events = 0;
1290         host->cmd_status = 0;
1291         host->data_status = 0;
1292         host->dir_status = 0;
1293
1294         data = cmd->data;
1295         if (data) {
1296                 mci_writel(host, TMOUT, 0xFFFFFFFF);
1297                 mci_writel(host, BYTCNT, data->blksz*data->blocks);
1298                 mci_writel(host, BLKSIZ, data->blksz);
1299         }
1300
1301         cmdflags = dw_mci_prepare_command(slot->mmc, cmd);
1302
1303         /* this is the first command, send the initialization clock */
1304         if (test_and_clear_bit(DW_MMC_CARD_NEED_INIT, &slot->flags))
1305                 cmdflags |= SDMMC_CMD_INIT;
1306
1307         if (data) {
1308                 dw_mci_submit_data(host, data);
1309                 wmb(); /* drain writebuffer */
1310         }
1311
1312         dw_mci_start_command(host, cmd, cmdflags);
1313
1314         if (cmd->opcode == SD_SWITCH_VOLTAGE) {
1315                 unsigned long irqflags;
1316
1317                 /*
1318                  * Databook says to fail after 2ms w/ no response, but evidence
1319                  * shows that sometimes the cmd11 interrupt takes over 130ms.
1320                  * We'll set to 500ms, plus an extra jiffy just in case jiffies
1321                  * is just about to roll over.
1322                  *
1323                  * We do this whole thing under spinlock and only if the
1324                  * command hasn't already completed (indicating the the irq
1325                  * already ran so we don't want the timeout).
1326                  */
1327                 spin_lock_irqsave(&host->irq_lock, irqflags);
1328                 if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
1329                         mod_timer(&host->cmd11_timer,
1330                                 jiffies + msecs_to_jiffies(500) + 1);
1331                 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1332         }
1333
1334         host->stop_cmdr = dw_mci_prep_stop_abort(host, cmd);
1335 }
1336
1337 static void dw_mci_start_request(struct dw_mci *host,
1338                                  struct dw_mci_slot *slot)
1339 {
1340         struct mmc_request *mrq = slot->mrq;
1341         struct mmc_command *cmd;
1342
1343         cmd = mrq->sbc ? mrq->sbc : mrq->cmd;
1344         __dw_mci_start_request(host, slot, cmd);
1345 }
1346
1347 /* must be called with host->lock held */
1348 static void dw_mci_queue_request(struct dw_mci *host, struct dw_mci_slot *slot,
1349                                  struct mmc_request *mrq)
1350 {
1351         dev_vdbg(&slot->mmc->class_dev, "queue request: state=%d\n",
1352                  host->state);
1353
1354         slot->mrq = mrq;
1355
1356         if (host->state == STATE_WAITING_CMD11_DONE) {
1357                 dev_warn(&slot->mmc->class_dev,
1358                          "Voltage change didn't complete\n");
1359                 /*
1360                  * this case isn't expected to happen, so we can
1361                  * either crash here or just try to continue on
1362                  * in the closest possible state
1363                  */
1364                 host->state = STATE_IDLE;
1365         }
1366
1367         if (host->state == STATE_IDLE) {
1368                 host->state = STATE_SENDING_CMD;
1369                 dw_mci_start_request(host, slot);
1370         } else {
1371                 list_add_tail(&slot->queue_node, &host->queue);
1372         }
1373 }
1374
1375 static void dw_mci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1376 {
1377         struct dw_mci_slot *slot = mmc_priv(mmc);
1378         struct dw_mci *host = slot->host;
1379
1380         WARN_ON(slot->mrq);
1381
1382         /*
1383          * The check for card presence and queueing of the request must be
1384          * atomic, otherwise the card could be removed in between and the
1385          * request wouldn't fail until another card was inserted.
1386          */
1387
1388         if (!dw_mci_get_cd(mmc)) {
1389                 mrq->cmd->error = -ENOMEDIUM;
1390                 mmc_request_done(mmc, mrq);
1391                 return;
1392         }
1393
1394         spin_lock_bh(&host->lock);
1395
1396         dw_mci_queue_request(host, slot, mrq);
1397
1398         spin_unlock_bh(&host->lock);
1399 }
1400
1401 static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1402 {
1403         struct dw_mci_slot *slot = mmc_priv(mmc);
1404         const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
1405         u32 regs;
1406         int ret;
1407
1408         switch (ios->bus_width) {
1409         case MMC_BUS_WIDTH_4:
1410                 slot->ctype = SDMMC_CTYPE_4BIT;
1411                 break;
1412         case MMC_BUS_WIDTH_8:
1413                 slot->ctype = SDMMC_CTYPE_8BIT;
1414                 break;
1415         default:
1416                 /* set default 1 bit mode */
1417                 slot->ctype = SDMMC_CTYPE_1BIT;
1418         }
1419
1420         regs = mci_readl(slot->host, UHS_REG);
1421
1422         /* DDR mode set */
1423         if (ios->timing == MMC_TIMING_MMC_DDR52 ||
1424             ios->timing == MMC_TIMING_UHS_DDR50 ||
1425             ios->timing == MMC_TIMING_MMC_HS400)
1426                 regs |= ((0x1 << slot->id) << 16);
1427         else
1428                 regs &= ~((0x1 << slot->id) << 16);
1429
1430         mci_writel(slot->host, UHS_REG, regs);
1431         slot->host->timing = ios->timing;
1432
1433         /*
1434          * Use mirror of ios->clock to prevent race with mmc
1435          * core ios update when finding the minimum.
1436          */
1437         slot->clock = ios->clock;
1438
1439         if (drv_data && drv_data->set_ios)
1440                 drv_data->set_ios(slot->host, ios);
1441
1442         switch (ios->power_mode) {
1443         case MMC_POWER_UP:
1444                 if (!IS_ERR(mmc->supply.vmmc)) {
1445                         ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc,
1446                                         ios->vdd);
1447                         if (ret) {
1448                                 dev_err(slot->host->dev,
1449                                         "failed to enable vmmc regulator\n");
1450                                 /*return, if failed turn on vmmc*/
1451                                 return;
1452                         }
1453                 }
1454                 set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
1455                 regs = mci_readl(slot->host, PWREN);
1456                 regs |= (1 << slot->id);
1457                 mci_writel(slot->host, PWREN, regs);
1458                 break;
1459         case MMC_POWER_ON:
1460                 if (!slot->host->vqmmc_enabled) {
1461                         if (!IS_ERR(mmc->supply.vqmmc)) {
1462                                 ret = regulator_enable(mmc->supply.vqmmc);
1463                                 if (ret < 0)
1464                                         dev_err(slot->host->dev,
1465                                                 "failed to enable vqmmc\n");
1466                                 else
1467                                         slot->host->vqmmc_enabled = true;
1468
1469                         } else {
1470                                 /* Keep track so we don't reset again */
1471                                 slot->host->vqmmc_enabled = true;
1472                         }
1473
1474                         /* Reset our state machine after powering on */
1475                         dw_mci_ctrl_reset(slot->host,
1476                                           SDMMC_CTRL_ALL_RESET_FLAGS);
1477                 }
1478
1479                 /* Adjust clock / bus width after power is up */
1480                 dw_mci_setup_bus(slot, false);
1481
1482                 break;
1483         case MMC_POWER_OFF:
1484                 /* Turn clock off before power goes down */
1485                 dw_mci_setup_bus(slot, false);
1486
1487                 if (!IS_ERR(mmc->supply.vmmc))
1488                         mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1489
1490                 if (!IS_ERR(mmc->supply.vqmmc) && slot->host->vqmmc_enabled)
1491                         regulator_disable(mmc->supply.vqmmc);
1492                 slot->host->vqmmc_enabled = false;
1493
1494                 regs = mci_readl(slot->host, PWREN);
1495                 regs &= ~(1 << slot->id);
1496                 mci_writel(slot->host, PWREN, regs);
1497                 break;
1498         default:
1499                 break;
1500         }
1501
1502         if (slot->host->state == STATE_WAITING_CMD11_DONE && ios->clock != 0)
1503                 slot->host->state = STATE_IDLE;
1504 }
1505
1506 static int dw_mci_card_busy(struct mmc_host *mmc)
1507 {
1508         struct dw_mci_slot *slot = mmc_priv(mmc);
1509         u32 status;
1510
1511         /*
1512          * Check the busy bit which is low when DAT[3:0]
1513          * (the data lines) are 0000
1514          */
1515         status = mci_readl(slot->host, STATUS);
1516
1517         return !!(status & SDMMC_STATUS_BUSY);
1518 }
1519
1520 static int dw_mci_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios)
1521 {
1522         struct dw_mci_slot *slot = mmc_priv(mmc);
1523         struct dw_mci *host = slot->host;
1524         const struct dw_mci_drv_data *drv_data = host->drv_data;
1525         u32 uhs;
1526         u32 v18 = SDMMC_UHS_18V << slot->id;
1527         int ret;
1528
1529         if (drv_data && drv_data->switch_voltage)
1530                 return drv_data->switch_voltage(mmc, ios);
1531
1532         /*
1533          * Program the voltage.  Note that some instances of dw_mmc may use
1534          * the UHS_REG for this.  For other instances (like exynos) the UHS_REG
1535          * does no harm but you need to set the regulator directly.  Try both.
1536          */
1537         uhs = mci_readl(host, UHS_REG);
1538         if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330)
1539                 uhs &= ~v18;
1540         else
1541                 uhs |= v18;
1542
1543         if (!IS_ERR(mmc->supply.vqmmc)) {
1544                 ret = mmc_regulator_set_vqmmc(mmc, ios);
1545
1546                 if (ret) {
1547                         dev_dbg(&mmc->class_dev,
1548                                          "Regulator set error %d - %s V\n",
1549                                          ret, uhs & v18 ? "1.8" : "3.3");
1550                         return ret;
1551                 }
1552         }
1553         mci_writel(host, UHS_REG, uhs);
1554
1555         return 0;
1556 }
1557
1558 static int dw_mci_get_ro(struct mmc_host *mmc)
1559 {
1560         int read_only;
1561         struct dw_mci_slot *slot = mmc_priv(mmc);
1562         int gpio_ro = mmc_gpio_get_ro(mmc);
1563
1564         /* Use platform get_ro function, else try on board write protect */
1565         if (gpio_ro >= 0)
1566                 read_only = gpio_ro;
1567         else
1568                 read_only =
1569                         mci_readl(slot->host, WRTPRT) & (1 << slot->id) ? 1 : 0;
1570
1571         dev_dbg(&mmc->class_dev, "card is %s\n",
1572                 read_only ? "read-only" : "read-write");
1573
1574         return read_only;
1575 }
1576
1577 static void dw_mci_hw_reset(struct mmc_host *mmc)
1578 {
1579         struct dw_mci_slot *slot = mmc_priv(mmc);
1580         struct dw_mci *host = slot->host;
1581         int reset;
1582
1583         if (host->use_dma == TRANS_MODE_IDMAC)
1584                 dw_mci_idmac_reset(host);
1585
1586         if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET |
1587                                      SDMMC_CTRL_FIFO_RESET))
1588                 return;
1589
1590         /*
1591          * According to eMMC spec, card reset procedure:
1592          * tRstW >= 1us:   RST_n pulse width
1593          * tRSCA >= 200us: RST_n to Command time
1594          * tRSTH >= 1us:   RST_n high period
1595          */
1596         reset = mci_readl(host, RST_N);
1597         reset &= ~(SDMMC_RST_HWACTIVE << slot->id);
1598         mci_writel(host, RST_N, reset);
1599         usleep_range(1, 2);
1600         reset |= SDMMC_RST_HWACTIVE << slot->id;
1601         mci_writel(host, RST_N, reset);
1602         usleep_range(200, 300);
1603 }
1604
1605 static void dw_mci_init_card(struct mmc_host *mmc, struct mmc_card *card)
1606 {
1607         struct dw_mci_slot *slot = mmc_priv(mmc);
1608         struct dw_mci *host = slot->host;
1609
1610         /*
1611          * Low power mode will stop the card clock when idle.  According to the
1612          * description of the CLKENA register we should disable low power mode
1613          * for SDIO cards if we need SDIO interrupts to work.
1614          */
1615         if (mmc->caps & MMC_CAP_SDIO_IRQ) {
1616                 const u32 clken_low_pwr = SDMMC_CLKEN_LOW_PWR << slot->id;
1617                 u32 clk_en_a_old;
1618                 u32 clk_en_a;
1619
1620                 clk_en_a_old = mci_readl(host, CLKENA);
1621
1622                 if (card->type == MMC_TYPE_SDIO ||
1623                     card->type == MMC_TYPE_SD_COMBO) {
1624                         if (!test_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags)) {
1625                                 pm_runtime_get_noresume(mmc->parent);
1626                                 set_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags);
1627                         }
1628                         clk_en_a = clk_en_a_old & ~clken_low_pwr;
1629                 } else {
1630                         if (test_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags)) {
1631                                 pm_runtime_put_noidle(mmc->parent);
1632                                 clear_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags);
1633                         }
1634                         clk_en_a = clk_en_a_old | clken_low_pwr;
1635                 }
1636
1637                 if (clk_en_a != clk_en_a_old) {
1638                         mci_writel(host, CLKENA, clk_en_a);
1639                         mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
1640                                      SDMMC_CMD_PRV_DAT_WAIT, 0);
1641                 }
1642         }
1643 }
1644
1645 static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
1646 {
1647         struct dw_mci_slot *slot = mmc_priv(mmc);
1648         struct dw_mci *host = slot->host;
1649         unsigned long irqflags;
1650         u32 int_mask;
1651
1652         spin_lock_irqsave(&host->irq_lock, irqflags);
1653
1654         /* Enable/disable Slot Specific SDIO interrupt */
1655         int_mask = mci_readl(host, INTMASK);
1656         if (enb)
1657                 int_mask |= SDMMC_INT_SDIO(slot->sdio_id);
1658         else
1659                 int_mask &= ~SDMMC_INT_SDIO(slot->sdio_id);
1660         mci_writel(host, INTMASK, int_mask);
1661
1662         spin_unlock_irqrestore(&host->irq_lock, irqflags);
1663 }
1664
1665 static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode)
1666 {
1667         struct dw_mci_slot *slot = mmc_priv(mmc);
1668         struct dw_mci *host = slot->host;
1669         const struct dw_mci_drv_data *drv_data = host->drv_data;
1670         int err = -EINVAL;
1671
1672         if (drv_data && drv_data->execute_tuning)
1673                 err = drv_data->execute_tuning(slot, opcode);
1674         return err;
1675 }
1676
1677 static int dw_mci_prepare_hs400_tuning(struct mmc_host *mmc,
1678                                        struct mmc_ios *ios)
1679 {
1680         struct dw_mci_slot *slot = mmc_priv(mmc);
1681         struct dw_mci *host = slot->host;
1682         const struct dw_mci_drv_data *drv_data = host->drv_data;
1683
1684         if (drv_data && drv_data->prepare_hs400_tuning)
1685                 return drv_data->prepare_hs400_tuning(host, ios);
1686
1687         return 0;
1688 }
1689
1690 static bool dw_mci_reset(struct dw_mci *host)
1691 {
1692         u32 flags = SDMMC_CTRL_RESET | SDMMC_CTRL_FIFO_RESET;
1693         bool ret = false;
1694         u32 status = 0;
1695
1696         /*
1697          * Resetting generates a block interrupt, hence setting
1698          * the scatter-gather pointer to NULL.
1699          */
1700         if (host->sg) {
1701                 sg_miter_stop(&host->sg_miter);
1702                 host->sg = NULL;
1703         }
1704
1705         if (host->use_dma)
1706                 flags |= SDMMC_CTRL_DMA_RESET;
1707
1708         if (dw_mci_ctrl_reset(host, flags)) {
1709                 /*
1710                  * In all cases we clear the RAWINTS
1711                  * register to clear any interrupts.
1712                  */
1713                 mci_writel(host, RINTSTS, 0xFFFFFFFF);
1714
1715                 if (!host->use_dma) {
1716                         ret = true;
1717                         goto ciu_out;
1718                 }
1719
1720                 /* Wait for dma_req to be cleared */
1721                 if (readl_poll_timeout_atomic(host->regs + SDMMC_STATUS,
1722                                               status,
1723                                               !(status & SDMMC_STATUS_DMA_REQ),
1724                                               1, 500 * USEC_PER_MSEC)) {
1725                         dev_err(host->dev,
1726                                 "%s: Timeout waiting for dma_req to be cleared\n",
1727                                 __func__);
1728                         goto ciu_out;
1729                 }
1730
1731                 /* when using DMA next we reset the fifo again */
1732                 if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_FIFO_RESET))
1733                         goto ciu_out;
1734         } else {
1735                 /* if the controller reset bit did clear, then set clock regs */
1736                 if (!(mci_readl(host, CTRL) & SDMMC_CTRL_RESET)) {
1737                         dev_err(host->dev,
1738                                 "%s: fifo/dma reset bits didn't clear but ciu was reset, doing clock update\n",
1739                                 __func__);
1740                         goto ciu_out;
1741                 }
1742         }
1743
1744         if (host->use_dma == TRANS_MODE_IDMAC)
1745                 /* It is also recommended that we reset and reprogram idmac */
1746                 dw_mci_idmac_reset(host);
1747
1748         ret = true;
1749
1750 ciu_out:
1751         /* After a CTRL reset we need to have CIU set clock registers  */
1752         mci_send_cmd(host->cur_slot, SDMMC_CMD_UPD_CLK, 0);
1753
1754         return ret;
1755 }
1756
1757 static const struct mmc_host_ops dw_mci_ops = {
1758         .request                = dw_mci_request,
1759         .pre_req                = dw_mci_pre_req,
1760         .post_req               = dw_mci_post_req,
1761         .set_ios                = dw_mci_set_ios,
1762         .get_ro                 = dw_mci_get_ro,
1763         .get_cd                 = dw_mci_get_cd,
1764         .hw_reset               = dw_mci_hw_reset,
1765         .enable_sdio_irq        = dw_mci_enable_sdio_irq,
1766         .execute_tuning         = dw_mci_execute_tuning,
1767         .card_busy              = dw_mci_card_busy,
1768         .start_signal_voltage_switch = dw_mci_switch_voltage,
1769         .init_card              = dw_mci_init_card,
1770         .prepare_hs400_tuning   = dw_mci_prepare_hs400_tuning,
1771 };
1772
1773 static void dw_mci_request_end(struct dw_mci *host, struct mmc_request *mrq)
1774         __releases(&host->lock)
1775         __acquires(&host->lock)
1776 {
1777         struct dw_mci_slot *slot;
1778         struct mmc_host *prev_mmc = host->cur_slot->mmc;
1779
1780         WARN_ON(host->cmd || host->data);
1781
1782         host->cur_slot->mrq = NULL;
1783         host->mrq = NULL;
1784         if (!list_empty(&host->queue)) {
1785                 slot = list_entry(host->queue.next,
1786                                   struct dw_mci_slot, queue_node);
1787                 list_del(&slot->queue_node);
1788                 dev_vdbg(host->dev, "list not empty: %s is next\n",
1789                          mmc_hostname(slot->mmc));
1790                 host->state = STATE_SENDING_CMD;
1791                 dw_mci_start_request(host, slot);
1792         } else {
1793                 dev_vdbg(host->dev, "list empty\n");
1794
1795                 if (host->state == STATE_SENDING_CMD11)
1796                         host->state = STATE_WAITING_CMD11_DONE;
1797                 else
1798                         host->state = STATE_IDLE;
1799         }
1800
1801         spin_unlock(&host->lock);
1802         mmc_request_done(prev_mmc, mrq);
1803         spin_lock(&host->lock);
1804 }
1805
1806 static int dw_mci_command_complete(struct dw_mci *host, struct mmc_command *cmd)
1807 {
1808         u32 status = host->cmd_status;
1809
1810         host->cmd_status = 0;
1811
1812         /* Read the response from the card (up to 16 bytes) */
1813         if (cmd->flags & MMC_RSP_PRESENT) {
1814                 if (cmd->flags & MMC_RSP_136) {
1815                         cmd->resp[3] = mci_readl(host, RESP0);
1816                         cmd->resp[2] = mci_readl(host, RESP1);
1817                         cmd->resp[1] = mci_readl(host, RESP2);
1818                         cmd->resp[0] = mci_readl(host, RESP3);
1819                 } else {
1820                         cmd->resp[0] = mci_readl(host, RESP0);
1821                         cmd->resp[1] = 0;
1822                         cmd->resp[2] = 0;
1823                         cmd->resp[3] = 0;
1824                 }
1825         }
1826
1827         if (status & SDMMC_INT_RTO)
1828                 cmd->error = -ETIMEDOUT;
1829         else if ((cmd->flags & MMC_RSP_CRC) && (status & SDMMC_INT_RCRC))
1830                 cmd->error = -EILSEQ;
1831         else if (status & SDMMC_INT_RESP_ERR)
1832                 cmd->error = -EIO;
1833         else
1834                 cmd->error = 0;
1835
1836         return cmd->error;
1837 }
1838
1839 static int dw_mci_data_complete(struct dw_mci *host, struct mmc_data *data)
1840 {
1841         u32 status = host->data_status;
1842
1843         if (status & DW_MCI_DATA_ERROR_FLAGS) {
1844                 if (status & SDMMC_INT_DRTO) {
1845                         data->error = -ETIMEDOUT;
1846                 } else if (status & SDMMC_INT_DCRC) {
1847                         data->error = -EILSEQ;
1848                 } else if (status & SDMMC_INT_EBE) {
1849                         if (host->dir_status ==
1850                                 DW_MCI_SEND_STATUS) {
1851                                 /*
1852                                  * No data CRC status was returned.
1853                                  * The number of bytes transferred
1854                                  * will be exaggerated in PIO mode.
1855                                  */
1856                                 data->bytes_xfered = 0;
1857                                 data->error = -ETIMEDOUT;
1858                         } else if (host->dir_status ==
1859                                         DW_MCI_RECV_STATUS) {
1860                                 data->error = -EILSEQ;
1861                         }
1862                 } else {
1863                         /* SDMMC_INT_SBE is included */
1864                         data->error = -EILSEQ;
1865                 }
1866
1867                 dev_dbg(host->dev, "data error, status 0x%08x\n", status);
1868
1869                 /*
1870                  * After an error, there may be data lingering
1871                  * in the FIFO
1872                  */
1873                 dw_mci_reset(host);
1874         } else {
1875                 data->bytes_xfered = data->blocks * data->blksz;
1876                 data->error = 0;
1877         }
1878
1879         return data->error;
1880 }
1881
1882 static void dw_mci_set_drto(struct dw_mci *host)
1883 {
1884         unsigned int drto_clks;
1885         unsigned int drto_ms;
1886
1887         drto_clks = mci_readl(host, TMOUT) >> 8;
1888         drto_ms = DIV_ROUND_UP(drto_clks, host->bus_hz / 1000);
1889
1890         /* add a bit spare time */
1891         drto_ms += 10;
1892
1893         mod_timer(&host->dto_timer, jiffies + msecs_to_jiffies(drto_ms));
1894 }
1895
1896 static void dw_mci_tasklet_func(unsigned long priv)
1897 {
1898         struct dw_mci *host = (struct dw_mci *)priv;
1899         struct mmc_data *data;
1900         struct mmc_command *cmd;
1901         struct mmc_request *mrq;
1902         enum dw_mci_state state;
1903         enum dw_mci_state prev_state;
1904         unsigned int err;
1905
1906         spin_lock(&host->lock);
1907
1908         state = host->state;
1909         data = host->data;
1910         mrq = host->mrq;
1911
1912         do {
1913                 prev_state = state;
1914
1915                 switch (state) {
1916                 case STATE_IDLE:
1917                 case STATE_WAITING_CMD11_DONE:
1918                         break;
1919
1920                 case STATE_SENDING_CMD11:
1921                 case STATE_SENDING_CMD:
1922                         if (!test_and_clear_bit(EVENT_CMD_COMPLETE,
1923                                                 &host->pending_events))
1924                                 break;
1925
1926                         cmd = host->cmd;
1927                         host->cmd = NULL;
1928                         set_bit(EVENT_CMD_COMPLETE, &host->completed_events);
1929                         err = dw_mci_command_complete(host, cmd);
1930                         if (cmd == mrq->sbc && !err) {
1931                                 prev_state = state = STATE_SENDING_CMD;
1932                                 __dw_mci_start_request(host, host->cur_slot,
1933                                                        mrq->cmd);
1934                                 goto unlock;
1935                         }
1936
1937                         if (cmd->data && err) {
1938                                 /*
1939                                  * During UHS tuning sequence, sending the stop
1940                                  * command after the response CRC error would
1941                                  * throw the system into a confused state
1942                                  * causing all future tuning phases to report
1943                                  * failure.
1944                                  *
1945                                  * In such case controller will move into a data
1946                                  * transfer state after a response error or
1947                                  * response CRC error. Let's let that finish
1948                                  * before trying to send a stop, so we'll go to
1949                                  * STATE_SENDING_DATA.
1950                                  *
1951                                  * Although letting the data transfer take place
1952                                  * will waste a bit of time (we already know
1953                                  * the command was bad), it can't cause any
1954                                  * errors since it's possible it would have
1955                                  * taken place anyway if this tasklet got
1956                                  * delayed. Allowing the transfer to take place
1957                                  * avoids races and keeps things simple.
1958                                  */
1959                                 if ((err != -ETIMEDOUT) &&
1960                                     (cmd->opcode == MMC_SEND_TUNING_BLOCK)) {
1961                                         state = STATE_SENDING_DATA;
1962                                         continue;
1963                                 }
1964
1965                                 dw_mci_stop_dma(host);
1966                                 send_stop_abort(host, data);
1967                                 state = STATE_SENDING_STOP;
1968                                 break;
1969                         }
1970
1971                         if (!cmd->data || err) {
1972                                 dw_mci_request_end(host, mrq);
1973                                 goto unlock;
1974                         }
1975
1976                         prev_state = state = STATE_SENDING_DATA;
1977                         /* fall through */
1978
1979                 case STATE_SENDING_DATA:
1980                         /*
1981                          * We could get a data error and never a transfer
1982                          * complete so we'd better check for it here.
1983                          *
1984                          * Note that we don't really care if we also got a
1985                          * transfer complete; stopping the DMA and sending an
1986                          * abort won't hurt.
1987                          */
1988                         if (test_and_clear_bit(EVENT_DATA_ERROR,
1989                                                &host->pending_events)) {
1990                                 dw_mci_stop_dma(host);
1991                                 if (!(host->data_status & (SDMMC_INT_DRTO |
1992                                                            SDMMC_INT_EBE)))
1993                                         send_stop_abort(host, data);
1994                                 state = STATE_DATA_ERROR;
1995                                 break;
1996                         }
1997
1998                         if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
1999                                                 &host->pending_events)) {
2000                                 /*
2001                                  * If all data-related interrupts don't come
2002                                  * within the given time in reading data state.
2003                                  */
2004                                 if (host->dir_status == DW_MCI_RECV_STATUS)
2005                                         dw_mci_set_drto(host);
2006                                 break;
2007                         }
2008
2009                         set_bit(EVENT_XFER_COMPLETE, &host->completed_events);
2010
2011                         /*
2012                          * Handle an EVENT_DATA_ERROR that might have shown up
2013                          * before the transfer completed.  This might not have
2014                          * been caught by the check above because the interrupt
2015                          * could have gone off between the previous check and
2016                          * the check for transfer complete.
2017                          *
2018                          * Technically this ought not be needed assuming we
2019                          * get a DATA_COMPLETE eventually (we'll notice the
2020                          * error and end the request), but it shouldn't hurt.
2021                          *
2022                          * This has the advantage of sending the stop command.
2023                          */
2024                         if (test_and_clear_bit(EVENT_DATA_ERROR,
2025                                                &host->pending_events)) {
2026                                 dw_mci_stop_dma(host);
2027                                 if (!(host->data_status & (SDMMC_INT_DRTO |
2028                                                            SDMMC_INT_EBE)))
2029                                         send_stop_abort(host, data);
2030                                 state = STATE_DATA_ERROR;
2031                                 break;
2032                         }
2033                         prev_state = state = STATE_DATA_BUSY;
2034
2035                         /* fall through */
2036
2037                 case STATE_DATA_BUSY:
2038                         if (!test_and_clear_bit(EVENT_DATA_COMPLETE,
2039                                                 &host->pending_events)) {
2040                                 /*
2041                                  * If data error interrupt comes but data over
2042                                  * interrupt doesn't come within the given time.
2043                                  * in reading data state.
2044                                  */
2045                                 if (host->dir_status == DW_MCI_RECV_STATUS)
2046                                         dw_mci_set_drto(host);
2047                                 break;
2048                         }
2049
2050                         host->data = NULL;
2051                         set_bit(EVENT_DATA_COMPLETE, &host->completed_events);
2052                         err = dw_mci_data_complete(host, data);
2053
2054                         if (!err) {
2055                                 if (!data->stop || mrq->sbc) {
2056                                         if (mrq->sbc && data->stop)
2057                                                 data->stop->error = 0;
2058                                         dw_mci_request_end(host, mrq);
2059                                         goto unlock;
2060                                 }
2061
2062                                 /* stop command for open-ended transfer*/
2063                                 if (data->stop)
2064                                         send_stop_abort(host, data);
2065                         } else {
2066                                 /*
2067                                  * If we don't have a command complete now we'll
2068                                  * never get one since we just reset everything;
2069                                  * better end the request.
2070                                  *
2071                                  * If we do have a command complete we'll fall
2072                                  * through to the SENDING_STOP command and
2073                                  * everything will be peachy keen.
2074                                  */
2075                                 if (!test_bit(EVENT_CMD_COMPLETE,
2076                                               &host->pending_events)) {
2077                                         host->cmd = NULL;
2078                                         dw_mci_request_end(host, mrq);
2079                                         goto unlock;
2080                                 }
2081                         }
2082
2083                         /*
2084                          * If err has non-zero,
2085                          * stop-abort command has been already issued.
2086                          */
2087                         prev_state = state = STATE_SENDING_STOP;
2088
2089                         /* fall through */
2090
2091                 case STATE_SENDING_STOP:
2092                         if (!test_and_clear_bit(EVENT_CMD_COMPLETE,
2093                                                 &host->pending_events))
2094                                 break;
2095
2096                         /* CMD error in data command */
2097                         if (mrq->cmd->error && mrq->data)
2098                                 dw_mci_reset(host);
2099
2100                         host->cmd = NULL;
2101                         host->data = NULL;
2102
2103                         if (!mrq->sbc && mrq->stop)
2104                                 dw_mci_command_complete(host, mrq->stop);
2105                         else
2106                                 host->cmd_status = 0;
2107
2108                         dw_mci_request_end(host, mrq);
2109                         goto unlock;
2110
2111                 case STATE_DATA_ERROR:
2112                         if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
2113                                                 &host->pending_events))
2114                                 break;
2115
2116                         state = STATE_DATA_BUSY;
2117                         break;
2118                 }
2119         } while (state != prev_state);
2120
2121         host->state = state;
2122 unlock:
2123         spin_unlock(&host->lock);
2124
2125 }
2126
2127 /* push final bytes to part_buf, only use during push */
2128 static void dw_mci_set_part_bytes(struct dw_mci *host, void *buf, int cnt)
2129 {
2130         memcpy((void *)&host->part_buf, buf, cnt);
2131         host->part_buf_count = cnt;
2132 }
2133
2134 /* append bytes to part_buf, only use during push */
2135 static int dw_mci_push_part_bytes(struct dw_mci *host, void *buf, int cnt)
2136 {
2137         cnt = min(cnt, (1 << host->data_shift) - host->part_buf_count);
2138         memcpy((void *)&host->part_buf + host->part_buf_count, buf, cnt);
2139         host->part_buf_count += cnt;
2140         return cnt;
2141 }
2142
2143 /* pull first bytes from part_buf, only use during pull */
2144 static int dw_mci_pull_part_bytes(struct dw_mci *host, void *buf, int cnt)
2145 {
2146         cnt = min_t(int, cnt, host->part_buf_count);
2147         if (cnt) {
2148                 memcpy(buf, (void *)&host->part_buf + host->part_buf_start,
2149                        cnt);
2150                 host->part_buf_count -= cnt;
2151                 host->part_buf_start += cnt;
2152         }
2153         return cnt;
2154 }
2155
2156 /* pull final bytes from the part_buf, assuming it's just been filled */
2157 static void dw_mci_pull_final_bytes(struct dw_mci *host, void *buf, int cnt)
2158 {
2159         memcpy(buf, &host->part_buf, cnt);
2160         host->part_buf_start = cnt;
2161         host->part_buf_count = (1 << host->data_shift) - cnt;
2162 }
2163
2164 static void dw_mci_push_data16(struct dw_mci *host, void *buf, int cnt)
2165 {
2166         struct mmc_data *data = host->data;
2167         int init_cnt = cnt;
2168
2169         /* try and push anything in the part_buf */
2170         if (unlikely(host->part_buf_count)) {
2171                 int len = dw_mci_push_part_bytes(host, buf, cnt);
2172
2173                 buf += len;
2174                 cnt -= len;
2175                 if (host->part_buf_count == 2) {
2176                         mci_fifo_writew(host->fifo_reg, host->part_buf16);
2177                         host->part_buf_count = 0;
2178                 }
2179         }
2180 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2181         if (unlikely((unsigned long)buf & 0x1)) {
2182                 while (cnt >= 2) {
2183                         u16 aligned_buf[64];
2184                         int len = min(cnt & -2, (int)sizeof(aligned_buf));
2185                         int items = len >> 1;
2186                         int i;
2187                         /* memcpy from input buffer into aligned buffer */
2188                         memcpy(aligned_buf, buf, len);
2189                         buf += len;
2190                         cnt -= len;
2191                         /* push data from aligned buffer into fifo */
2192                         for (i = 0; i < items; ++i)
2193                                 mci_fifo_writew(host->fifo_reg, aligned_buf[i]);
2194                 }
2195         } else
2196 #endif
2197         {
2198                 u16 *pdata = buf;
2199
2200                 for (; cnt >= 2; cnt -= 2)
2201                         mci_fifo_writew(host->fifo_reg, *pdata++);
2202                 buf = pdata;
2203         }
2204         /* put anything remaining in the part_buf */
2205         if (cnt) {
2206                 dw_mci_set_part_bytes(host, buf, cnt);
2207                  /* Push data if we have reached the expected data length */
2208                 if ((data->bytes_xfered + init_cnt) ==
2209                     (data->blksz * data->blocks))
2210                         mci_fifo_writew(host->fifo_reg, host->part_buf16);
2211         }
2212 }
2213
2214 static void dw_mci_pull_data16(struct dw_mci *host, void *buf, int cnt)
2215 {
2216 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2217         if (unlikely((unsigned long)buf & 0x1)) {
2218                 while (cnt >= 2) {
2219                         /* pull data from fifo into aligned buffer */
2220                         u16 aligned_buf[64];
2221                         int len = min(cnt & -2, (int)sizeof(aligned_buf));
2222                         int items = len >> 1;
2223                         int i;
2224
2225                         for (i = 0; i < items; ++i)
2226                                 aligned_buf[i] = mci_fifo_readw(host->fifo_reg);
2227                         /* memcpy from aligned buffer into output buffer */
2228                         memcpy(buf, aligned_buf, len);
2229                         buf += len;
2230                         cnt -= len;
2231                 }
2232         } else
2233 #endif
2234         {
2235                 u16 *pdata = buf;
2236
2237                 for (; cnt >= 2; cnt -= 2)
2238                         *pdata++ = mci_fifo_readw(host->fifo_reg);
2239                 buf = pdata;
2240         }
2241         if (cnt) {
2242                 host->part_buf16 = mci_fifo_readw(host->fifo_reg);
2243                 dw_mci_pull_final_bytes(host, buf, cnt);
2244         }
2245 }
2246
2247 static void dw_mci_push_data32(struct dw_mci *host, void *buf, int cnt)
2248 {
2249         struct mmc_data *data = host->data;
2250         int init_cnt = cnt;
2251
2252         /* try and push anything in the part_buf */
2253         if (unlikely(host->part_buf_count)) {
2254                 int len = dw_mci_push_part_bytes(host, buf, cnt);
2255
2256                 buf += len;
2257                 cnt -= len;
2258                 if (host->part_buf_count == 4) {
2259                         mci_fifo_writel(host->fifo_reg, host->part_buf32);
2260                         host->part_buf_count = 0;
2261                 }
2262         }
2263 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2264         if (unlikely((unsigned long)buf & 0x3)) {
2265                 while (cnt >= 4) {
2266                         u32 aligned_buf[32];
2267                         int len = min(cnt & -4, (int)sizeof(aligned_buf));
2268                         int items = len >> 2;
2269                         int i;
2270                         /* memcpy from input buffer into aligned buffer */
2271                         memcpy(aligned_buf, buf, len);
2272                         buf += len;
2273                         cnt -= len;
2274                         /* push data from aligned buffer into fifo */
2275                         for (i = 0; i < items; ++i)
2276                                 mci_fifo_writel(host->fifo_reg, aligned_buf[i]);
2277                 }
2278         } else
2279 #endif
2280         {
2281                 u32 *pdata = buf;
2282
2283                 for (; cnt >= 4; cnt -= 4)
2284                         mci_fifo_writel(host->fifo_reg, *pdata++);
2285                 buf = pdata;
2286         }
2287         /* put anything remaining in the part_buf */
2288         if (cnt) {
2289                 dw_mci_set_part_bytes(host, buf, cnt);
2290                  /* Push data if we have reached the expected data length */
2291                 if ((data->bytes_xfered + init_cnt) ==
2292                     (data->blksz * data->blocks))
2293                         mci_fifo_writel(host->fifo_reg, host->part_buf32);
2294         }
2295 }
2296
2297 static void dw_mci_pull_data32(struct dw_mci *host, void *buf, int cnt)
2298 {
2299 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2300         if (unlikely((unsigned long)buf & 0x3)) {
2301                 while (cnt >= 4) {
2302                         /* pull data from fifo into aligned buffer */
2303                         u32 aligned_buf[32];
2304                         int len = min(cnt & -4, (int)sizeof(aligned_buf));
2305                         int items = len >> 2;
2306                         int i;
2307
2308                         for (i = 0; i < items; ++i)
2309                                 aligned_buf[i] = mci_fifo_readl(host->fifo_reg);
2310                         /* memcpy from aligned buffer into output buffer */
2311                         memcpy(buf, aligned_buf, len);
2312                         buf += len;
2313                         cnt -= len;
2314                 }
2315         } else
2316 #endif
2317         {
2318                 u32 *pdata = buf;
2319
2320                 for (; cnt >= 4; cnt -= 4)
2321                         *pdata++ = mci_fifo_readl(host->fifo_reg);
2322                 buf = pdata;
2323         }
2324         if (cnt) {
2325                 host->part_buf32 = mci_fifo_readl(host->fifo_reg);
2326                 dw_mci_pull_final_bytes(host, buf, cnt);
2327         }
2328 }
2329
2330 static void dw_mci_push_data64(struct dw_mci *host, void *buf, int cnt)
2331 {
2332         struct mmc_data *data = host->data;
2333         int init_cnt = cnt;
2334
2335         /* try and push anything in the part_buf */
2336         if (unlikely(host->part_buf_count)) {
2337                 int len = dw_mci_push_part_bytes(host, buf, cnt);
2338
2339                 buf += len;
2340                 cnt -= len;
2341
2342                 if (host->part_buf_count == 8) {
2343                         mci_fifo_writeq(host->fifo_reg, host->part_buf);
2344                         host->part_buf_count = 0;
2345                 }
2346         }
2347 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2348         if (unlikely((unsigned long)buf & 0x7)) {
2349                 while (cnt >= 8) {
2350                         u64 aligned_buf[16];
2351                         int len = min(cnt & -8, (int)sizeof(aligned_buf));
2352                         int items = len >> 3;
2353                         int i;
2354                         /* memcpy from input buffer into aligned buffer */
2355                         memcpy(aligned_buf, buf, len);
2356                         buf += len;
2357                         cnt -= len;
2358                         /* push data from aligned buffer into fifo */
2359                         for (i = 0; i < items; ++i)
2360                                 mci_fifo_writeq(host->fifo_reg, aligned_buf[i]);
2361                 }
2362         } else
2363 #endif
2364         {
2365                 u64 *pdata = buf;
2366
2367                 for (; cnt >= 8; cnt -= 8)
2368                         mci_fifo_writeq(host->fifo_reg, *pdata++);
2369                 buf = pdata;
2370         }
2371         /* put anything remaining in the part_buf */
2372         if (cnt) {
2373                 dw_mci_set_part_bytes(host, buf, cnt);
2374                 /* Push data if we have reached the expected data length */
2375                 if ((data->bytes_xfered + init_cnt) ==
2376                     (data->blksz * data->blocks))
2377                         mci_fifo_writeq(host->fifo_reg, host->part_buf);
2378         }
2379 }
2380
2381 static void dw_mci_pull_data64(struct dw_mci *host, void *buf, int cnt)
2382 {
2383 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2384         if (unlikely((unsigned long)buf & 0x7)) {
2385                 while (cnt >= 8) {
2386                         /* pull data from fifo into aligned buffer */
2387                         u64 aligned_buf[16];
2388                         int len = min(cnt & -8, (int)sizeof(aligned_buf));
2389                         int items = len >> 3;
2390                         int i;
2391
2392                         for (i = 0; i < items; ++i)
2393                                 aligned_buf[i] = mci_fifo_readq(host->fifo_reg);
2394
2395                         /* memcpy from aligned buffer into output buffer */
2396                         memcpy(buf, aligned_buf, len);
2397                         buf += len;
2398                         cnt -= len;
2399                 }
2400         } else
2401 #endif
2402         {
2403                 u64 *pdata = buf;
2404
2405                 for (; cnt >= 8; cnt -= 8)
2406                         *pdata++ = mci_fifo_readq(host->fifo_reg);
2407                 buf = pdata;
2408         }
2409         if (cnt) {
2410                 host->part_buf = mci_fifo_readq(host->fifo_reg);
2411                 dw_mci_pull_final_bytes(host, buf, cnt);
2412         }
2413 }
2414
2415 static void dw_mci_pull_data(struct dw_mci *host, void *buf, int cnt)
2416 {
2417         int len;
2418
2419         /* get remaining partial bytes */
2420         len = dw_mci_pull_part_bytes(host, buf, cnt);
2421         if (unlikely(len == cnt))
2422                 return;
2423         buf += len;
2424         cnt -= len;
2425
2426         /* get the rest of the data */
2427         host->pull_data(host, buf, cnt);
2428 }
2429
2430 static void dw_mci_read_data_pio(struct dw_mci *host, bool dto)
2431 {
2432         struct sg_mapping_iter *sg_miter = &host->sg_miter;
2433         void *buf;
2434         unsigned int offset;
2435         struct mmc_data *data = host->data;
2436         int shift = host->data_shift;
2437         u32 status;
2438         unsigned int len;
2439         unsigned int remain, fcnt;
2440
2441         do {
2442                 if (!sg_miter_next(sg_miter))
2443                         goto done;
2444
2445                 host->sg = sg_miter->piter.sg;
2446                 buf = sg_miter->addr;
2447                 remain = sg_miter->length;
2448                 offset = 0;
2449
2450                 do {
2451                         fcnt = (SDMMC_GET_FCNT(mci_readl(host, STATUS))
2452                                         << shift) + host->part_buf_count;
2453                         len = min(remain, fcnt);
2454                         if (!len)
2455                                 break;
2456                         dw_mci_pull_data(host, (void *)(buf + offset), len);
2457                         data->bytes_xfered += len;
2458                         offset += len;
2459                         remain -= len;
2460                 } while (remain);
2461
2462                 sg_miter->consumed = offset;
2463                 status = mci_readl(host, MINTSTS);
2464                 mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
2465         /* if the RXDR is ready read again */
2466         } while ((status & SDMMC_INT_RXDR) ||
2467                  (dto && SDMMC_GET_FCNT(mci_readl(host, STATUS))));
2468
2469         if (!remain) {
2470                 if (!sg_miter_next(sg_miter))
2471                         goto done;
2472                 sg_miter->consumed = 0;
2473         }
2474         sg_miter_stop(sg_miter);
2475         return;
2476
2477 done:
2478         sg_miter_stop(sg_miter);
2479         host->sg = NULL;
2480         smp_wmb(); /* drain writebuffer */
2481         set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
2482 }
2483
2484 static void dw_mci_write_data_pio(struct dw_mci *host)
2485 {
2486         struct sg_mapping_iter *sg_miter = &host->sg_miter;
2487         void *buf;
2488         unsigned int offset;
2489         struct mmc_data *data = host->data;
2490         int shift = host->data_shift;
2491         u32 status;
2492         unsigned int len;
2493         unsigned int fifo_depth = host->fifo_depth;
2494         unsigned int remain, fcnt;
2495
2496         do {
2497                 if (!sg_miter_next(sg_miter))
2498                         goto done;
2499
2500                 host->sg = sg_miter->piter.sg;
2501                 buf = sg_miter->addr;
2502                 remain = sg_miter->length;
2503                 offset = 0;
2504
2505                 do {
2506                         fcnt = ((fifo_depth -
2507                                  SDMMC_GET_FCNT(mci_readl(host, STATUS)))
2508                                         << shift) - host->part_buf_count;
2509                         len = min(remain, fcnt);
2510                         if (!len)
2511                                 break;
2512                         host->push_data(host, (void *)(buf + offset), len);
2513                         data->bytes_xfered += len;
2514                         offset += len;
2515                         remain -= len;
2516                 } while (remain);
2517
2518                 sg_miter->consumed = offset;
2519                 status = mci_readl(host, MINTSTS);
2520                 mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
2521         } while (status & SDMMC_INT_TXDR); /* if TXDR write again */
2522
2523         if (!remain) {
2524                 if (!sg_miter_next(sg_miter))
2525                         goto done;
2526                 sg_miter->consumed = 0;
2527         }
2528         sg_miter_stop(sg_miter);
2529         return;
2530
2531 done:
2532         sg_miter_stop(sg_miter);
2533         host->sg = NULL;
2534         smp_wmb(); /* drain writebuffer */
2535         set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
2536 }
2537
2538 static void dw_mci_cmd_interrupt(struct dw_mci *host, u32 status)
2539 {
2540         if (!host->cmd_status)
2541                 host->cmd_status = status;
2542
2543         smp_wmb(); /* drain writebuffer */
2544
2545         set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
2546         tasklet_schedule(&host->tasklet);
2547 }
2548
2549 static void dw_mci_handle_cd(struct dw_mci *host)
2550 {
2551         int i;
2552
2553         for (i = 0; i < host->num_slots; i++) {
2554                 struct dw_mci_slot *slot = host->slot[i];
2555
2556                 if (!slot)
2557                         continue;
2558
2559                 if (slot->mmc->ops->card_event)
2560                         slot->mmc->ops->card_event(slot->mmc);
2561                 mmc_detect_change(slot->mmc,
2562                         msecs_to_jiffies(host->pdata->detect_delay_ms));
2563         }
2564 }
2565
2566 static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
2567 {
2568         struct dw_mci *host = dev_id;
2569         u32 pending;
2570         int i;
2571
2572         pending = mci_readl(host, MINTSTS); /* read-only mask reg */
2573
2574         if (pending) {
2575                 /* Check volt switch first, since it can look like an error */
2576                 if ((host->state == STATE_SENDING_CMD11) &&
2577                     (pending & SDMMC_INT_VOLT_SWITCH)) {
2578                         unsigned long irqflags;
2579
2580                         mci_writel(host, RINTSTS, SDMMC_INT_VOLT_SWITCH);
2581                         pending &= ~SDMMC_INT_VOLT_SWITCH;
2582
2583                         /*
2584                          * Hold the lock; we know cmd11_timer can't be kicked
2585                          * off after the lock is released, so safe to delete.
2586                          */
2587                         spin_lock_irqsave(&host->irq_lock, irqflags);
2588                         dw_mci_cmd_interrupt(host, pending);
2589                         spin_unlock_irqrestore(&host->irq_lock, irqflags);
2590
2591                         del_timer(&host->cmd11_timer);
2592                 }
2593
2594                 if (pending & DW_MCI_CMD_ERROR_FLAGS) {
2595                         mci_writel(host, RINTSTS, DW_MCI_CMD_ERROR_FLAGS);
2596                         host->cmd_status = pending;
2597                         smp_wmb(); /* drain writebuffer */
2598                         set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
2599                 }
2600
2601                 if (pending & DW_MCI_DATA_ERROR_FLAGS) {
2602                         /* if there is an error report DATA_ERROR */
2603                         mci_writel(host, RINTSTS, DW_MCI_DATA_ERROR_FLAGS);
2604                         host->data_status = pending;
2605                         smp_wmb(); /* drain writebuffer */
2606                         set_bit(EVENT_DATA_ERROR, &host->pending_events);
2607                         tasklet_schedule(&host->tasklet);
2608                 }
2609
2610                 if (pending & SDMMC_INT_DATA_OVER) {
2611                         del_timer(&host->dto_timer);
2612
2613                         mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
2614                         if (!host->data_status)
2615                                 host->data_status = pending;
2616                         smp_wmb(); /* drain writebuffer */
2617                         if (host->dir_status == DW_MCI_RECV_STATUS) {
2618                                 if (host->sg != NULL)
2619                                         dw_mci_read_data_pio(host, true);
2620                         }
2621                         set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
2622                         tasklet_schedule(&host->tasklet);
2623                 }
2624
2625                 if (pending & SDMMC_INT_RXDR) {
2626                         mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
2627                         if (host->dir_status == DW_MCI_RECV_STATUS && host->sg)
2628                                 dw_mci_read_data_pio(host, false);
2629                 }
2630
2631                 if (pending & SDMMC_INT_TXDR) {
2632                         mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
2633                         if (host->dir_status == DW_MCI_SEND_STATUS && host->sg)
2634                                 dw_mci_write_data_pio(host);
2635                 }
2636
2637                 if (pending & SDMMC_INT_CMD_DONE) {
2638                         mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE);
2639                         dw_mci_cmd_interrupt(host, pending);
2640                 }
2641
2642                 if (pending & SDMMC_INT_CD) {
2643                         mci_writel(host, RINTSTS, SDMMC_INT_CD);
2644                         dw_mci_handle_cd(host);
2645                 }
2646
2647                 /* Handle SDIO Interrupts */
2648                 for (i = 0; i < host->num_slots; i++) {
2649                         struct dw_mci_slot *slot = host->slot[i];
2650
2651                         if (!slot)
2652                                 continue;
2653
2654                         if (pending & SDMMC_INT_SDIO(slot->sdio_id)) {
2655                                 mci_writel(host, RINTSTS,
2656                                            SDMMC_INT_SDIO(slot->sdio_id));
2657                                 mmc_signal_sdio_irq(slot->mmc);
2658                         }
2659                 }
2660
2661         }
2662
2663         if (host->use_dma != TRANS_MODE_IDMAC)
2664                 return IRQ_HANDLED;
2665
2666         /* Handle IDMA interrupts */
2667         if (host->dma_64bit_address == 1) {
2668                 pending = mci_readl(host, IDSTS64);
2669                 if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
2670                         mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_TI |
2671                                                         SDMMC_IDMAC_INT_RI);
2672                         mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_NI);
2673                         if (!test_bit(EVENT_DATA_ERROR, &host->pending_events))
2674                                 host->dma_ops->complete((void *)host);
2675                 }
2676         } else {
2677                 pending = mci_readl(host, IDSTS);
2678                 if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
2679                         mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI |
2680                                                         SDMMC_IDMAC_INT_RI);
2681                         mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
2682                         if (!test_bit(EVENT_DATA_ERROR, &host->pending_events))
2683                                 host->dma_ops->complete((void *)host);
2684                 }
2685         }
2686
2687         return IRQ_HANDLED;
2688 }
2689
2690 static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
2691 {
2692         struct mmc_host *mmc;
2693         struct dw_mci_slot *slot;
2694         const struct dw_mci_drv_data *drv_data = host->drv_data;
2695         int ctrl_id, ret;
2696         u32 freq[2];
2697
2698         mmc = mmc_alloc_host(sizeof(struct dw_mci_slot), host->dev);
2699         if (!mmc)
2700                 return -ENOMEM;
2701
2702         slot = mmc_priv(mmc);
2703         slot->id = id;
2704         slot->sdio_id = host->sdio_id0 + id;
2705         slot->mmc = mmc;
2706         slot->host = host;
2707         host->slot[id] = slot;
2708
2709         mmc->ops = &dw_mci_ops;
2710         if (of_property_read_u32_array(host->dev->of_node,
2711                                        "clock-freq-min-max", freq, 2)) {
2712                 mmc->f_min = DW_MCI_FREQ_MIN;
2713                 mmc->f_max = DW_MCI_FREQ_MAX;
2714         } else {
2715                 dev_info(host->dev,
2716                         "'clock-freq-min-max' property was deprecated.\n");
2717                 mmc->f_min = freq[0];
2718                 mmc->f_max = freq[1];
2719         }
2720
2721         /*if there are external regulators, get them*/
2722         ret = mmc_regulator_get_supply(mmc);
2723         if (ret == -EPROBE_DEFER)
2724                 goto err_host_allocated;
2725
2726         if (!mmc->ocr_avail)
2727                 mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
2728
2729         if (host->pdata->caps)
2730                 mmc->caps = host->pdata->caps;
2731
2732         /*
2733          * Support MMC_CAP_ERASE by default.
2734          * It needs to use trim/discard/erase commands.
2735          */
2736         mmc->caps |= MMC_CAP_ERASE;
2737
2738         if (host->pdata->pm_caps)
2739                 mmc->pm_caps = host->pdata->pm_caps;
2740
2741         if (host->dev->of_node) {
2742                 ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
2743                 if (ctrl_id < 0)
2744                         ctrl_id = 0;
2745         } else {
2746                 ctrl_id = to_platform_device(host->dev)->id;
2747         }
2748         if (drv_data && drv_data->caps)
2749                 mmc->caps |= drv_data->caps[ctrl_id];
2750
2751         if (host->pdata->caps2)
2752                 mmc->caps2 = host->pdata->caps2;
2753
2754         ret = mmc_of_parse(mmc);
2755         if (ret)
2756                 goto err_host_allocated;
2757
2758         /* Useful defaults if platform data is unset. */
2759         if (host->use_dma == TRANS_MODE_IDMAC) {
2760                 mmc->max_segs = host->ring_size;
2761                 mmc->max_blk_size = 65535;
2762                 mmc->max_seg_size = 0x1000;
2763                 mmc->max_req_size = mmc->max_seg_size * host->ring_size;
2764                 mmc->max_blk_count = mmc->max_req_size / 512;
2765         } else if (host->use_dma == TRANS_MODE_EDMAC) {
2766                 mmc->max_segs = 64;
2767                 mmc->max_blk_size = 65535;
2768                 mmc->max_blk_count = 65535;
2769                 mmc->max_req_size =
2770                                 mmc->max_blk_size * mmc->max_blk_count;
2771                 mmc->max_seg_size = mmc->max_req_size;
2772         } else {
2773                 /* TRANS_MODE_PIO */
2774                 mmc->max_segs = 64;
2775                 mmc->max_blk_size = 65535; /* BLKSIZ is 16 bits */
2776                 mmc->max_blk_count = 512;
2777                 mmc->max_req_size = mmc->max_blk_size *
2778                                     mmc->max_blk_count;
2779                 mmc->max_seg_size = mmc->max_req_size;
2780         }
2781
2782         dw_mci_get_cd(mmc);
2783
2784         ret = mmc_add_host(mmc);
2785         if (ret)
2786                 goto err_host_allocated;
2787
2788 #if defined(CONFIG_DEBUG_FS)
2789         dw_mci_init_debugfs(slot);
2790 #endif
2791
2792         return 0;
2793
2794 err_host_allocated:
2795         mmc_free_host(mmc);
2796         return ret;
2797 }
2798
2799 static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id)
2800 {
2801         /* Debugfs stuff is cleaned up by mmc core */
2802         mmc_remove_host(slot->mmc);
2803         slot->host->slot[id] = NULL;
2804         mmc_free_host(slot->mmc);
2805 }
2806
2807 static void dw_mci_init_dma(struct dw_mci *host)
2808 {
2809         int addr_config;
2810         struct device *dev = host->dev;
2811         struct device_node *np = dev->of_node;
2812
2813         /*
2814         * Check tansfer mode from HCON[17:16]
2815         * Clear the ambiguous description of dw_mmc databook:
2816         * 2b'00: No DMA Interface -> Actually means using Internal DMA block
2817         * 2b'01: DesignWare DMA Interface -> Synopsys DW-DMA block
2818         * 2b'10: Generic DMA Interface -> non-Synopsys generic DMA block
2819         * 2b'11: Non DW DMA Interface -> pio only
2820         * Compared to DesignWare DMA Interface, Generic DMA Interface has a
2821         * simpler request/acknowledge handshake mechanism and both of them
2822         * are regarded as external dma master for dw_mmc.
2823         */
2824         host->use_dma = SDMMC_GET_TRANS_MODE(mci_readl(host, HCON));
2825         if (host->use_dma == DMA_INTERFACE_IDMA) {
2826                 host->use_dma = TRANS_MODE_IDMAC;
2827         } else if (host->use_dma == DMA_INTERFACE_DWDMA ||
2828                    host->use_dma == DMA_INTERFACE_GDMA) {
2829                 host->use_dma = TRANS_MODE_EDMAC;
2830         } else {
2831                 goto no_dma;
2832         }
2833
2834         /* Determine which DMA interface to use */
2835         if (host->use_dma == TRANS_MODE_IDMAC) {
2836                 /*
2837                 * Check ADDR_CONFIG bit in HCON to find
2838                 * IDMAC address bus width
2839                 */
2840                 addr_config = SDMMC_GET_ADDR_CONFIG(mci_readl(host, HCON));
2841
2842                 if (addr_config == 1) {
2843                         /* host supports IDMAC in 64-bit address mode */
2844                         host->dma_64bit_address = 1;
2845                         dev_info(host->dev,
2846                                  "IDMAC supports 64-bit address mode.\n");
2847                         if (!dma_set_mask(host->dev, DMA_BIT_MASK(64)))
2848                                 dma_set_coherent_mask(host->dev,
2849                                                       DMA_BIT_MASK(64));
2850                 } else {
2851                         /* host supports IDMAC in 32-bit address mode */
2852                         host->dma_64bit_address = 0;
2853                         dev_info(host->dev,
2854                                  "IDMAC supports 32-bit address mode.\n");
2855                 }
2856
2857                 /* Alloc memory for sg translation */
2858                 host->sg_cpu = dmam_alloc_coherent(host->dev,
2859                                                    DESC_RING_BUF_SZ,
2860                                                    &host->sg_dma, GFP_KERNEL);
2861                 if (!host->sg_cpu) {
2862                         dev_err(host->dev,
2863                                 "%s: could not alloc DMA memory\n",
2864                                 __func__);
2865                         goto no_dma;
2866                 }
2867
2868                 host->dma_ops = &dw_mci_idmac_ops;
2869                 dev_info(host->dev, "Using internal DMA controller.\n");
2870         } else {
2871                 /* TRANS_MODE_EDMAC: check dma bindings again */
2872                 if ((of_property_count_strings(np, "dma-names") < 0) ||
2873                     (!of_find_property(np, "dmas", NULL))) {
2874                         goto no_dma;
2875                 }
2876                 host->dma_ops = &dw_mci_edmac_ops;
2877                 dev_info(host->dev, "Using external DMA controller.\n");
2878         }
2879
2880         if (host->dma_ops->init && host->dma_ops->start &&
2881             host->dma_ops->stop && host->dma_ops->cleanup) {
2882                 if (host->dma_ops->init(host)) {
2883                         dev_err(host->dev, "%s: Unable to initialize DMA Controller.\n",
2884                                 __func__);
2885                         goto no_dma;
2886                 }
2887         } else {
2888                 dev_err(host->dev, "DMA initialization not found.\n");
2889                 goto no_dma;
2890         }
2891
2892         return;
2893
2894 no_dma:
2895         dev_info(host->dev, "Using PIO mode.\n");
2896         host->use_dma = TRANS_MODE_PIO;
2897 }
2898
2899 static void dw_mci_cmd11_timer(unsigned long arg)
2900 {
2901         struct dw_mci *host = (struct dw_mci *)arg;
2902
2903         if (host->state != STATE_SENDING_CMD11) {
2904                 dev_warn(host->dev, "Unexpected CMD11 timeout\n");
2905                 return;
2906         }
2907
2908         host->cmd_status = SDMMC_INT_RTO;
2909         set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
2910         tasklet_schedule(&host->tasklet);
2911 }
2912
2913 static void dw_mci_dto_timer(unsigned long arg)
2914 {
2915         struct dw_mci *host = (struct dw_mci *)arg;
2916
2917         switch (host->state) {
2918         case STATE_SENDING_DATA:
2919         case STATE_DATA_BUSY:
2920                 /*
2921                  * If DTO interrupt does NOT come in sending data state,
2922                  * we should notify the driver to terminate current transfer
2923                  * and report a data timeout to the core.
2924                  */
2925                 host->data_status = SDMMC_INT_DRTO;
2926                 set_bit(EVENT_DATA_ERROR, &host->pending_events);
2927                 set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
2928                 tasklet_schedule(&host->tasklet);
2929                 break;
2930         default:
2931                 break;
2932         }
2933 }
2934
2935 #ifdef CONFIG_OF
2936 static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
2937 {
2938         struct dw_mci_board *pdata;
2939         struct device *dev = host->dev;
2940         struct device_node *np = dev->of_node;
2941         const struct dw_mci_drv_data *drv_data = host->drv_data;
2942         int ret;
2943         u32 clock_frequency;
2944
2945         pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
2946         if (!pdata)
2947                 return ERR_PTR(-ENOMEM);
2948
2949         /* find reset controller when exist */
2950         pdata->rstc = devm_reset_control_get_optional(dev, "reset");
2951         if (IS_ERR(pdata->rstc)) {
2952                 if (PTR_ERR(pdata->rstc) == -EPROBE_DEFER)
2953                         return ERR_PTR(-EPROBE_DEFER);
2954         }
2955
2956         /* find out number of slots supported */
2957         of_property_read_u32(np, "num-slots", &pdata->num_slots);
2958
2959         if (of_property_read_u32(np, "fifo-depth", &pdata->fifo_depth))
2960                 dev_info(dev,
2961                          "fifo-depth property not found, using value of FIFOTH register as default\n");
2962
2963         of_property_read_u32(np, "card-detect-delay", &pdata->detect_delay_ms);
2964
2965         of_property_read_u32(np, "data-addr", &host->data_addr_override);
2966
2967         if (of_get_property(np, "fifo-watermark-aligned", NULL))
2968                 host->wm_aligned = true;
2969
2970         if (!of_property_read_u32(np, "clock-frequency", &clock_frequency))
2971                 pdata->bus_hz = clock_frequency;
2972
2973         if (drv_data && drv_data->parse_dt) {
2974                 ret = drv_data->parse_dt(host);
2975                 if (ret)
2976                         return ERR_PTR(ret);
2977         }
2978
2979         return pdata;
2980 }
2981
2982 #else /* CONFIG_OF */
2983 static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
2984 {
2985         return ERR_PTR(-EINVAL);
2986 }
2987 #endif /* CONFIG_OF */
2988
2989 static void dw_mci_enable_cd(struct dw_mci *host)
2990 {
2991         unsigned long irqflags;
2992         u32 temp;
2993         int i;
2994         struct dw_mci_slot *slot;
2995
2996         /*
2997          * No need for CD if all slots have a non-error GPIO
2998          * as well as broken card detection is found.
2999          */
3000         for (i = 0; i < host->num_slots; i++) {
3001                 slot = host->slot[i];
3002                 if (slot->mmc->caps & MMC_CAP_NEEDS_POLL)
3003                         return;
3004
3005                 if (mmc_gpio_get_cd(slot->mmc) < 0)
3006                         break;
3007         }
3008         if (i == host->num_slots)
3009                 return;
3010
3011         spin_lock_irqsave(&host->irq_lock, irqflags);
3012         temp = mci_readl(host, INTMASK);
3013         temp  |= SDMMC_INT_CD;
3014         mci_writel(host, INTMASK, temp);
3015         spin_unlock_irqrestore(&host->irq_lock, irqflags);
3016 }
3017
3018 int dw_mci_probe(struct dw_mci *host)
3019 {
3020         const struct dw_mci_drv_data *drv_data = host->drv_data;
3021         int width, i, ret = 0;
3022         u32 fifo_size;
3023         int init_slots = 0;
3024
3025         if (!host->pdata) {
3026                 host->pdata = dw_mci_parse_dt(host);
3027                 if (PTR_ERR(host->pdata) == -EPROBE_DEFER) {
3028                         return -EPROBE_DEFER;
3029                 } else if (IS_ERR(host->pdata)) {
3030                         dev_err(host->dev, "platform data not available\n");
3031                         return -EINVAL;
3032                 }
3033         }
3034
3035         host->biu_clk = devm_clk_get(host->dev, "biu");
3036         if (IS_ERR(host->biu_clk)) {
3037                 dev_dbg(host->dev, "biu clock not available\n");
3038         } else {
3039                 ret = clk_prepare_enable(host->biu_clk);
3040                 if (ret) {
3041                         dev_err(host->dev, "failed to enable biu clock\n");
3042                         return ret;
3043                 }
3044         }
3045
3046         host->ciu_clk = devm_clk_get(host->dev, "ciu");
3047         if (IS_ERR(host->ciu_clk)) {
3048                 dev_dbg(host->dev, "ciu clock not available\n");
3049                 host->bus_hz = host->pdata->bus_hz;
3050         } else {
3051                 ret = clk_prepare_enable(host->ciu_clk);
3052                 if (ret) {
3053                         dev_err(host->dev, "failed to enable ciu clock\n");
3054                         goto err_clk_biu;
3055                 }
3056
3057                 if (host->pdata->bus_hz) {
3058                         ret = clk_set_rate(host->ciu_clk, host->pdata->bus_hz);
3059                         if (ret)
3060                                 dev_warn(host->dev,
3061                                          "Unable to set bus rate to %uHz\n",
3062                                          host->pdata->bus_hz);
3063                 }
3064                 host->bus_hz = clk_get_rate(host->ciu_clk);
3065         }
3066
3067         if (!host->bus_hz) {
3068                 dev_err(host->dev,
3069                         "Platform data must supply bus speed\n");
3070                 ret = -ENODEV;
3071                 goto err_clk_ciu;
3072         }
3073
3074         if (drv_data && drv_data->init) {
3075                 ret = drv_data->init(host);
3076                 if (ret) {
3077                         dev_err(host->dev,
3078                                 "implementation specific init failed\n");
3079                         goto err_clk_ciu;
3080                 }
3081         }
3082
3083         if (!IS_ERR(host->pdata->rstc)) {
3084                 reset_control_assert(host->pdata->rstc);
3085                 usleep_range(10, 50);
3086                 reset_control_deassert(host->pdata->rstc);
3087         }
3088
3089         setup_timer(&host->cmd11_timer,
3090                     dw_mci_cmd11_timer, (unsigned long)host);
3091
3092         setup_timer(&host->dto_timer,
3093                     dw_mci_dto_timer, (unsigned long)host);
3094
3095         spin_lock_init(&host->lock);
3096         spin_lock_init(&host->irq_lock);
3097         INIT_LIST_HEAD(&host->queue);
3098
3099         /*
3100          * Get the host data width - this assumes that HCON has been set with
3101          * the correct values.
3102          */
3103         i = SDMMC_GET_HDATA_WIDTH(mci_readl(host, HCON));
3104         if (!i) {
3105                 host->push_data = dw_mci_push_data16;
3106                 host->pull_data = dw_mci_pull_data16;
3107                 width = 16;
3108                 host->data_shift = 1;
3109         } else if (i == 2) {
3110                 host->push_data = dw_mci_push_data64;
3111                 host->pull_data = dw_mci_pull_data64;
3112                 width = 64;
3113                 host->data_shift = 3;
3114         } else {
3115                 /* Check for a reserved value, and warn if it is */
3116                 WARN((i != 1),
3117                      "HCON reports a reserved host data width!\n"
3118                      "Defaulting to 32-bit access.\n");
3119                 host->push_data = dw_mci_push_data32;
3120                 host->pull_data = dw_mci_pull_data32;
3121                 width = 32;
3122                 host->data_shift = 2;
3123         }
3124
3125         /* Reset all blocks */
3126         if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS)) {
3127                 ret = -ENODEV;
3128                 goto err_clk_ciu;
3129         }
3130
3131         host->dma_ops = host->pdata->dma_ops;
3132         dw_mci_init_dma(host);
3133
3134         /* Clear the interrupts for the host controller */
3135         mci_writel(host, RINTSTS, 0xFFFFFFFF);
3136         mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
3137
3138         /* Put in max timeout */
3139         mci_writel(host, TMOUT, 0xFFFFFFFF);
3140
3141         /*
3142          * FIFO threshold settings  RxMark  = fifo_size / 2 - 1,
3143          *                          Tx Mark = fifo_size / 2 DMA Size = 8
3144          */
3145         if (!host->pdata->fifo_depth) {
3146                 /*
3147                  * Power-on value of RX_WMark is FIFO_DEPTH-1, but this may
3148                  * have been overwritten by the bootloader, just like we're
3149                  * about to do, so if you know the value for your hardware, you
3150                  * should put it in the platform data.
3151                  */
3152                 fifo_size = mci_readl(host, FIFOTH);
3153                 fifo_size = 1 + ((fifo_size >> 16) & 0xfff);
3154         } else {
3155                 fifo_size = host->pdata->fifo_depth;
3156         }
3157         host->fifo_depth = fifo_size;
3158         host->fifoth_val =
3159                 SDMMC_SET_FIFOTH(0x2, fifo_size / 2 - 1, fifo_size / 2);
3160         mci_writel(host, FIFOTH, host->fifoth_val);
3161
3162         /* disable clock to CIU */
3163         mci_writel(host, CLKENA, 0);
3164         mci_writel(host, CLKSRC, 0);
3165
3166         /*
3167          * In 2.40a spec, Data offset is changed.
3168          * Need to check the version-id and set data-offset for DATA register.
3169          */
3170         host->verid = SDMMC_GET_VERID(mci_readl(host, VERID));
3171         dev_info(host->dev, "Version ID is %04x\n", host->verid);
3172
3173         if (host->data_addr_override)
3174                 host->fifo_reg = host->regs + host->data_addr_override;
3175         else if (host->verid < DW_MMC_240A)
3176                 host->fifo_reg = host->regs + DATA_OFFSET;
3177         else
3178                 host->fifo_reg = host->regs + DATA_240A_OFFSET;
3179
3180         tasklet_init(&host->tasklet, dw_mci_tasklet_func, (unsigned long)host);
3181         ret = devm_request_irq(host->dev, host->irq, dw_mci_interrupt,
3182                                host->irq_flags, "dw-mci", host);
3183         if (ret)
3184                 goto err_dmaunmap;
3185
3186         if (host->pdata->num_slots)
3187                 host->num_slots = host->pdata->num_slots;
3188         else
3189                 host->num_slots = 1;
3190
3191         if (host->num_slots < 1 ||
3192             host->num_slots > SDMMC_GET_SLOT_NUM(mci_readl(host, HCON))) {
3193                 dev_err(host->dev,
3194                         "Platform data must supply correct num_slots.\n");
3195                 ret = -ENODEV;
3196                 goto err_clk_ciu;
3197         }
3198
3199         /*
3200          * Enable interrupts for command done, data over, data empty,
3201          * receive ready and error such as transmit, receive timeout, crc error
3202          */
3203         mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
3204                    SDMMC_INT_TXDR | SDMMC_INT_RXDR |
3205                    DW_MCI_ERROR_FLAGS);
3206         /* Enable mci interrupt */
3207         mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
3208
3209         dev_info(host->dev,
3210                  "DW MMC controller at irq %d,%d bit host data width,%u deep fifo\n",
3211                  host->irq, width, fifo_size);
3212
3213         /* We need at least one slot to succeed */
3214         for (i = 0; i < host->num_slots; i++) {
3215                 ret = dw_mci_init_slot(host, i);
3216                 if (ret)
3217                         dev_dbg(host->dev, "slot %d init failed\n", i);
3218                 else
3219                         init_slots++;
3220         }
3221
3222         if (init_slots) {
3223                 dev_info(host->dev, "%d slots initialized\n", init_slots);
3224         } else {
3225                 dev_dbg(host->dev,
3226                         "attempted to initialize %d slots, but failed on all\n",
3227                         host->num_slots);
3228                 goto err_dmaunmap;
3229         }
3230
3231         /* Now that slots are all setup, we can enable card detect */
3232         dw_mci_enable_cd(host);
3233
3234         return 0;
3235
3236 err_dmaunmap:
3237         if (host->use_dma && host->dma_ops->exit)
3238                 host->dma_ops->exit(host);
3239
3240         if (!IS_ERR(host->pdata->rstc))
3241                 reset_control_assert(host->pdata->rstc);
3242
3243 err_clk_ciu:
3244         clk_disable_unprepare(host->ciu_clk);
3245
3246 err_clk_biu:
3247         clk_disable_unprepare(host->biu_clk);
3248
3249         return ret;
3250 }
3251 EXPORT_SYMBOL(dw_mci_probe);
3252
3253 void dw_mci_remove(struct dw_mci *host)
3254 {
3255         int i;
3256
3257         for (i = 0; i < host->num_slots; i++) {
3258                 dev_dbg(host->dev, "remove slot %d\n", i);
3259                 if (host->slot[i])
3260                         dw_mci_cleanup_slot(host->slot[i], i);
3261         }
3262
3263         mci_writel(host, RINTSTS, 0xFFFFFFFF);
3264         mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
3265
3266         /* disable clock to CIU */
3267         mci_writel(host, CLKENA, 0);
3268         mci_writel(host, CLKSRC, 0);
3269
3270         if (host->use_dma && host->dma_ops->exit)
3271                 host->dma_ops->exit(host);
3272
3273         if (!IS_ERR(host->pdata->rstc))
3274                 reset_control_assert(host->pdata->rstc);
3275
3276         clk_disable_unprepare(host->ciu_clk);
3277         clk_disable_unprepare(host->biu_clk);
3278 }
3279 EXPORT_SYMBOL(dw_mci_remove);
3280
3281
3282
3283 #ifdef CONFIG_PM
3284 int dw_mci_runtime_suspend(struct device *dev)
3285 {
3286         struct dw_mci *host = dev_get_drvdata(dev);
3287
3288         if (host->use_dma && host->dma_ops->exit)
3289                 host->dma_ops->exit(host);
3290
3291         clk_disable_unprepare(host->ciu_clk);
3292
3293         if (host->cur_slot &&
3294             (mmc_can_gpio_cd(host->cur_slot->mmc) ||
3295              !mmc_card_is_removable(host->cur_slot->mmc)))
3296                 clk_disable_unprepare(host->biu_clk);
3297
3298         return 0;
3299 }
3300 EXPORT_SYMBOL(dw_mci_runtime_suspend);
3301
3302 int dw_mci_runtime_resume(struct device *dev)
3303 {
3304         int i, ret = 0;
3305         struct dw_mci *host = dev_get_drvdata(dev);
3306
3307         if (host->cur_slot &&
3308             (mmc_can_gpio_cd(host->cur_slot->mmc) ||
3309              !mmc_card_is_removable(host->cur_slot->mmc))) {
3310                 ret = clk_prepare_enable(host->biu_clk);
3311                 if (ret)
3312                         return ret;
3313         }
3314
3315         ret = clk_prepare_enable(host->ciu_clk);
3316         if (ret)
3317                 goto err;
3318
3319         if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS)) {
3320                 clk_disable_unprepare(host->ciu_clk);
3321                 ret = -ENODEV;
3322                 goto err;
3323         }
3324
3325         if (host->use_dma && host->dma_ops->init)
3326                 host->dma_ops->init(host);
3327
3328         /*
3329          * Restore the initial value at FIFOTH register
3330          * And Invalidate the prev_blksz with zero
3331          */
3332          mci_writel(host, FIFOTH, host->fifoth_val);
3333          host->prev_blksz = 0;
3334
3335         /* Put in max timeout */
3336         mci_writel(host, TMOUT, 0xFFFFFFFF);
3337
3338         mci_writel(host, RINTSTS, 0xFFFFFFFF);
3339         mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
3340                    SDMMC_INT_TXDR | SDMMC_INT_RXDR |
3341                    DW_MCI_ERROR_FLAGS);
3342         mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
3343
3344         for (i = 0; i < host->num_slots; i++) {
3345                 struct dw_mci_slot *slot = host->slot[i];
3346
3347                 if (!slot)
3348                         continue;
3349                 if (slot->mmc->pm_flags & MMC_PM_KEEP_POWER)
3350                         dw_mci_set_ios(slot->mmc, &slot->mmc->ios);
3351
3352                 /* Force setup bus to guarantee available clock output */
3353                 dw_mci_setup_bus(slot, true);
3354         }
3355
3356         /* Now that slots are all setup, we can enable card detect */
3357         dw_mci_enable_cd(host);
3358
3359         return 0;
3360
3361 err:
3362         if (host->cur_slot &&
3363             (mmc_can_gpio_cd(host->cur_slot->mmc) ||
3364              !mmc_card_is_removable(host->cur_slot->mmc)))
3365                 clk_disable_unprepare(host->biu_clk);
3366
3367         return ret;
3368 }
3369 EXPORT_SYMBOL(dw_mci_runtime_resume);
3370 #endif /* CONFIG_PM */
3371
3372 static int __init dw_mci_init(void)
3373 {
3374         pr_info("Synopsys Designware Multimedia Card Interface Driver\n");
3375         return 0;
3376 }
3377
3378 static void __exit dw_mci_exit(void)
3379 {
3380 }
3381
3382 module_init(dw_mci_init);
3383 module_exit(dw_mci_exit);
3384
3385 MODULE_DESCRIPTION("DW Multimedia Card Interface driver");
3386 MODULE_AUTHOR("NXP Semiconductor VietNam");
3387 MODULE_AUTHOR("Imagination Technologies Ltd");
3388 MODULE_LICENSE("GPL v2");