1 menu "MMC Host controller Support"
4 bool "MMC/SD/SDIO card support"
5 default ARM || PPC || SANDBOX
6 select HAVE_BLOCK_DEVICE
9 This selects MultiMediaCard, Secure Digital and Secure
12 If you want MMC/SD/SDIO support, you should say Y here and
13 also to your specific host controller driver.
16 bool "support for MMC/SD write operations"
20 Enable write access to MMC and SD Cards
23 bool "HW reset support for eMMC"
26 Ths select Hardware reset support aka pwrseq-emmc for eMMC
30 bool "Poll for broken card detection case"
32 If card detection feature is broken, just poll to detect.
35 bool "Enable MMC controllers using Driver Model"
39 This enables the MultiMediaCard (MMC) uclass which supports MMC and
40 Secure Digital I/O (SDIO) cards. Both removable (SD, micro-SD, etc.)
41 and non-removable (e.g. eMMC chip) devices are supported. These
42 appear as block devices in U-Boot and can support filesystems such
46 bool "Enable MMC controllers using Driver Model in SPL"
47 depends on SPL_DM && DM_MMC
50 This enables the MultiMediaCard (MMC) uclass which supports MMC and
51 Secure Digital I/O (SDIO) cards. Both removable (SD, micro-SD, etc.)
52 and non-removable (e.g. eMMC chip) devices are supported. These
53 appear as block devices in U-Boot and can support filesystems such
58 config MMC_SDHCI_ADMA_HELPERS
62 bool "Support for SPI-based MMC controller"
63 depends on DM_MMC && DM_SPI
65 This selects SPI-based MMC controllers.
66 If you have an MMC controller on a SPI bus, say Y here.
71 bool "Support CRC for SPI-based MMC controller"
75 This enables CRC for SPI-based MMC controllers.
80 bool "ARM AMBA Multimedia Card Interface and compatible support"
82 This selects the ARM(R) AMBA(R) PrimeCell Multimedia Card
83 Interface (PL180, PL181 and compatible) support.
84 If you have an ARM(R) platform with a Multimedia Card slot,
91 Some cards and hosts may sometimes behave unexpectedly (quirks).
92 This option enable workarounds to handle those quirks. Some of them
93 are enabled by default, other may require additional flags or are
94 enabled by the host driver.
96 config MMC_HW_PARTITIONING
97 bool "Support for HW partitioning command(eMMC)"
100 This adds a command and an API to do hardware partitioning on eMMC
103 config SUPPORT_EMMC_RPMB
104 bool "Support eMMC replay protected memory block (RPMB)"
107 Enable support for reading, writing and programming the
108 key for the Replay Protection Memory Block partition in eMMC.
110 config SUPPORT_EMMC_BOOT
111 bool "Support some additional features of the eMMC boot partitions"
113 Enable support for eMMC boot partitions. This also enables
114 extensions within the mmc command.
116 config MMC_IO_VOLTAGE
117 bool "Support IO voltage configuration"
119 IO voltage configuration allows selecting the voltage level of the IO
120 lines (not the level of main supply). This is required for UHS
121 support. For eMMC this not mandatory, but not enabling this option may
122 prevent the driver of using the faster modes.
124 config SPL_MMC_IO_VOLTAGE
125 bool "Support IO voltage configuration in SPL"
127 IO voltage configuration allows selecting the voltage level of the IO
128 lines (not the level of main supply). This is required for UHS
129 support. For eMMC this not mandatory, but not enabling this option may
130 prevent the driver of using the faster modes.
132 config MMC_UHS_SUPPORT
133 bool "enable UHS support"
134 depends on MMC_IO_VOLTAGE
136 The Ultra High Speed (UHS) bus is available on some SDHC and SDXC
137 cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus
138 frequency can go up to 208MHz (SDR104)
140 config SPL_MMC_UHS_SUPPORT
141 bool "enable UHS support in SPL"
142 depends on SPL_MMC_IO_VOLTAGE
144 The Ultra High Speed (UHS) bus is available on some SDHC and SDXC
145 cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus
146 frequency can go up to 208MHz (SDR104)
148 config MMC_HS400_ES_SUPPORT
149 bool "enable HS400 Enhanced Strobe support"
151 The HS400 Enhanced Strobe mode is support by some eMMC. The bus
152 frequency is up to 200MHz. This mode does not tune the IO.
154 config SPL_MMC_HS400_ES_SUPPORT
155 bool "enable HS400 Enhanced Strobe support in SPL"
157 The HS400 Enhanced Strobe mode is support by some eMMC. The bus
158 frequency is up to 200MHz. This mode does not tune the IO.
160 config MMC_HS400_SUPPORT
161 bool "enable HS400 support"
162 select MMC_HS200_SUPPORT
164 The HS400 mode is support by some eMMC. The bus frequency is up to
165 200MHz. This mode requires tuning the IO.
167 config SPL_MMC_HS400_SUPPORT
168 bool "enable HS400 support in SPL"
169 select SPL_MMC_HS200_SUPPORT
171 The HS400 mode is support by some eMMC. The bus frequency is up to
172 200MHz. This mode requires tuning the IO.
174 config MMC_HS200_SUPPORT
175 bool "enable HS200 support"
177 The HS200 mode is support by some eMMC. The bus frequency is up to
178 200MHz. This mode requires tuning the IO.
180 config SPL_MMC_HS200_SUPPORT
181 bool "enable HS200 support in SPL"
183 The HS200 mode is support by some eMMC. The bus frequency is up to
184 200MHz. This mode requires tuning the IO.
187 bool "Output more information about the MMC"
190 Enable the output of more information about the card such as the
196 This is an option for use by developer. Enable MMC core debugging.
198 If you need to see the MMC core message, say Y.
201 bool "TI DAVINCI Multimedia Card Interface support"
202 depends on ARCH_DAVINCI
205 This selects the TI DAVINCI Multimedia card Interface.
206 If you have an DAVINCI board with a Multimedia Card slot,
207 say Y here. If unsure, say N.
210 bool "Synopsys DesignWare Memory Card Interface"
213 This selects support for the Synopsys DesignWare Mobile Storage IP
214 block, this provides host support for SD and MMC interfaces, in both
215 PIO, internal DMA mode and external DMA mode.
217 config MMC_DW_CORTINA
218 bool "Cortina specific extensions for Synopsys DW Memory Card Interface"
223 This selects support for Cortina SoC specific extensions to the
224 Synopsys DesignWare Memory Card Interface driver. Select this option
225 for platforms based on Cortina CAxxxx Soc's.
228 bool "Exynos specific extensions for Synopsys DW Memory Card Interface"
229 depends on ARCH_EXYNOS
233 This selects support for Samsung Exynos SoC specific extensions to the
234 Synopsys DesignWare Memory Card Interface driver. Select this option
235 for platforms based on Exynos4 and Exynos5 SoC's.
238 bool "K3 specific extensions for Synopsys DW Memory Card Interface"
241 This selects support for Hisilicon K3 SoC specific extensions to the
242 Synopsys DesignWare Memory Card Interface driver. Select this option
243 for platforms based on Hisilicon K3 SoC's.
245 config MMC_DW_ROCKCHIP
246 bool "Rockchip SD/MMC controller support"
247 depends on DM_MMC && OF_CONTROL
250 This enables support for the Rockchip SD/MMM controller, which is
251 based on Designware IP. The device is compatible with at least
252 SD 3.0, SDIO 3.0 and MMC 4.5 and supports common eMMC chips as well
253 as removeable SD and micro-SD cards.
255 config MMC_DW_SOCFPGA
256 bool "SOCFPGA specific extensions for Synopsys DW Memory Card Interface"
257 depends on ARCH_SOCFPGA
261 This selects support for Altera SOCFPGA specific extensions to the
262 Synopsys DesignWare Memory Card Interface driver. Select this option
263 for platforms based on Altera SOCFPGA.
266 bool "Extensions for DW Memory Card Interface used in Synopsys ARC devboards"
269 depends on OF_CONTROL
272 This selects support for Synopsys DesignWare Memory Card Interface driver
273 extensions used in various Synopsys ARC devboards.
276 bool "Nexell SD/MMC controller support"
277 depends on ARCH_NEXELL
280 depends on PINCTRL_NEXELL
284 bool "Meson GX EMMC controller support"
285 depends on DM_MMC && BLK && ARCH_MESON
287 Support for EMMC host controller on Meson GX ARM SoCs platform (S905)
290 bool "Freescale i.MX21/27/31 or MPC512x Multimedia Card support"
292 This selects the Freescale i.MX21, i.MX27, i.MX31 or MPC512x
293 Multimedia Card Interface. If you have an i.MX or MPC512x platform
294 with a Multimedia Card slot, say Y here.
299 bool "Freescale MXS Multimedia Card Interface support"
300 depends on MX23 || MX28 || MX6 || MX7
303 select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7
304 select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7
306 This selects the Freescale SSP MMC controller found on MXS based
307 platforms like mx23/28.
312 bool "Support for MMC controllers on PCI"
315 This selects PCI-based MMC controllers.
316 If you have an MMC controller on a PCI bus, say Y here.
319 bool "Marvell Octeon Multimedia Card Interface support"
320 depends on (ARCH_OCTEON || ARCH_OCTEONTX || ARCH_OCTEONTX2)
323 This selects the Octeon Multimedia card Interface.
324 If you have an OcteonTX/TX2 or MIPS Octeon board with a
325 Multimedia Card slot, say Y here.
330 bool "Kirkwood MMC controller support"
331 depends on DM_MMC && BLK && ARCH_KIRKWOOD
333 Support for MMC host controller on Kirkwood SoCs.
334 If you are on a Kirkwood architecture, say Y here.
338 config PXA_MMC_GENERIC
339 bool "Support for MMC controllers on PXA"
341 This selects MMC controllers on PXA.
342 If you are on a PXA architecture, say Y here.
347 bool "TI OMAP High Speed Multimedia Card Interface support"
348 select DM_REGULATOR_PBIAS if DM_MMC && DM_REGULATOR
349 select DM_REGULATOR_PBIAS if DM_MMC && DM_REGULATOR
351 This selects the TI OMAP High Speed Multimedia card Interface.
352 If you have an omap2plus board with a Multimedia Card slot,
357 config MMC_OMAP_HS_ADMA
358 bool "ADMA support for OMAP HS MMC"
359 depends on MMC_OMAP_HS && !OMAP34XX
362 This enables support for the ADMA2 controller (SDA3.00 Part A2 DMA
363 controller). If supported by the hardware, selecting this option will
364 increase performances.
366 config MMC_OMAP36XX_PINS
367 bool "Enable MMC1 on OMAP36xx/37xx"
368 depends on OMAP34XX && MMC_OMAP_HS
370 This enables extended-drain in the MMC/SD/SDIO1I/O and
371 GPIO-associated I/O cells (gpio_126, gpio_127, and gpio_129)
372 specific to the OMAP36xx/37xx using MMC1
374 If you have a controller with this interface, say Y here.
379 bool "SuperH/Renesas ARM SoCs on-chip SDHI host controller support"
380 depends on ARCH_RMOBILE
382 Support for the on-chip SDHI host controller on SuperH/Renesas ARM SoCs platform
385 bool "SuperH/Renesas ARM SoCs on-chip MMCIF host controller support"
386 depends on ARCH_RMOBILE || SH
388 Support for the on-chip MMCIF host controller on SuperH/Renesas ARM SoCs platform
391 bool "UniPhier SD/MMC Host Controller support"
392 depends on ARCH_UNIPHIER
393 depends on BLK && DM_MMC
394 depends on OF_CONTROL
396 This selects support for the Matsushita SD/MMC Host Controller on
397 SocioNext UniPhier SoCs.
400 bool "Renesas R-Car SD/MMC Host Controller support"
401 depends on ARCH_RMOBILE
402 depends on BLK && DM_MMC
403 depends on OF_CONTROL
406 This selects support for the Matsushita SD/MMC Host Controller on
410 bool "BCM2835 family custom SD/MMC Host Controller support"
411 depends on ARCH_BCM283X
412 depends on BLK && DM_MMC
413 depends on OF_CONTROL
416 This selects support for the custom SD host controller in the BCM2835
419 If you have a BCM2835 platform with SD or MMC devices, say Y here.
424 bool "Ingenic JZ47xx SD/MMC Host Controller support"
425 depends on ARCH_JZ47XX
427 This selects support for the SD Card Controller on Ingenic JZ47xx SoCs.
430 bool "Sandbox MMC support"
432 depends on BLK && DM_MMC && OF_CONTROL
434 This select a dummy sandbox MMC driver. At present this does nothing
435 other than allow sandbox to be build with MMC support. This
436 improves build coverage for sandbox and makes it easier to detect
437 MMC build errors with sandbox.
440 bool "Secure Digital Host Controller Interface support"
442 This selects the generic Secure Digital Host Controller Interface.
443 It is used by manufacturers such as Texas Instruments(R), Ricoh(R)
444 and Toshiba(R). Most controllers found in laptops are of this type.
446 If you have a controller with this interface, say Y here.
450 config MMC_SDHCI_IO_ACCESSORS
454 This is silent Kconfig symbol that is selected by the drivers that
455 need to overwrite SDHCI IO memory accessors.
457 config MMC_SDHCI_SDMA
458 bool "Support SDHCI SDMA"
461 This enables support for the SDMA (Single Operation DMA) defined
462 in the SD Host Controller Standard Specification Version 1.00 .
464 config MMC_SDHCI_ADMA
465 bool "Support SDHCI ADMA2"
467 select MMC_SDHCI_ADMA_HELPERS
469 This enables support for the ADMA (Advanced DMA) defined
470 in the SD Host Controller Standard Specification Version 3.00
472 config SPL_MMC_SDHCI_ADMA
473 bool "Support SDHCI ADMA2 in SPL"
475 select MMC_SDHCI_ADMA_HELPERS
477 This enables support for the ADMA (Advanced DMA) defined
478 in the SD Host Controller Standard Specification Version 3.00 in SPL.
480 config MMC_SDHCI_ASPEED
481 bool "Aspeed SDHCI controller"
482 depends on ARCH_ASPEED
486 Enables support for the Aspeed SDHCI 2.0 controller present on Aspeed
487 SoCs. This device is compatible with SD 3.0 and/or MMC 4.3
488 specifications. On the AST2600, the device is also compatible with
489 MMC 5.1 and eMMC 3.0.
491 config MMC_SDHCI_ATMEL
492 bool "Atmel SDHCI controller support"
494 depends on DM_MMC && BLK && ARCH_AT91
497 This enables support for the Atmel SDHCI controller, which supports
498 the embedded MultiMedia Card (e.MMC) Specification V4.51, the SD
499 Memory Card Specification V3.0, and the SDIO V3.0 specification.
500 It is compliant with the SD Host Controller Standard V3.0
503 config MMC_SDHCI_BCM2835
504 tristate "SDHCI support for the BCM2835 SD/MMC Controller"
505 depends on ARCH_BCM283X
507 select MMC_SDHCI_IO_ACCESSORS
509 This selects the BCM2835 SD/MMC controller.
511 If you have a BCM2835 platform with SD or MMC devices,
516 config MMC_SDHCI_BCMSTB
517 tristate "SDHCI support for the BCMSTB SD/MMC Controller"
520 This selects the Broadcom set-top box SD/MMC controller.
522 If you have a BCMSTB platform with SD or MMC devices,
527 config MMC_SDHCI_CADENCE
528 bool "SDHCI support for the Cadence SD/SDIO/eMMC controller"
529 depends on BLK && DM_MMC
531 depends on OF_CONTROL
533 This selects the Cadence SD/SDIO/eMMC driver.
535 If you have a controller with this interface, say Y here.
539 config MMC_SDHCI_AM654
540 bool "SDHCI Controller on TI's Am654 devices"
543 depends on DM_MMC && OF_CONTROL && BLK
545 select MMC_SDHCI_IO_ACCESSORS
547 Support for Secure Digital Host Controller Interface (SDHCI)
548 controllers present on TI's AM654 SOCs.
550 config MMC_SDHCI_IPROC
551 bool "SDHCI support for the iProc SD/MMC Controller"
554 This selects the iProc SD/MMC controller.
556 If you have a Broadcom IPROC platform with SD or MMC devices,
561 config MMC_SDHCI_F_SDH30
562 bool "SDHCI support for Fujitsu Semiconductor F_SDH30"
563 depends on BLK && DM_MMC
566 This selects the Secure Digital Host Controller Interface (SDHCI)
567 Needed by some Fujitsu SoC for MMC / SD / SDIO support.
568 If you have a controller with this interface, say Y or M here.
571 config MMC_SDHCI_KONA
572 bool "SDHCI support on Broadcom KONA platform"
575 This selects the Broadcom Kona Secure Digital Host Controller
576 Interface(SDHCI) support.
577 This is used in Broadcom mobile SoCs.
579 If you have a controller with this interface, say Y here.
582 bool "Qualcomm SDHCI controller"
583 depends on BLK && DM_MMC
586 Enables support for SDHCI 2.0 controller present on some Qualcomm
587 Snapdragon devices. This device is compatible with eMMC v4.5 and
588 SD 3.0 specifications. Both SD and eMMC devices are supported.
589 Card-detect gpios are not supported.
592 bool "SDHCI support on Marvell platform"
593 depends on ARCH_MVEBU
596 This selects the Secure Digital Host Controller Interface on
599 If you have a controller with this interface, say Y here.
603 config MMC_SDHCI_PIC32
604 bool "Microchip PIC32 on-chip SDHCI support"
605 depends on DM_MMC && MACH_PIC32
608 Support for Microchip PIC32 SDHCI controller.
610 config MMC_SDHCI_ROCKCHIP
611 bool "Arasan SDHCI controller for Rockchip support"
612 depends on ARCH_ROCKCHIP
613 depends on DM_MMC && BLK
616 Support for Arasan SDHCI host controller on Rockchip ARM SoCs platform
619 bool "SDHCI support on Samsung S5P SoC"
622 This selects the Secure Digital Host Controller Interface (SDHCI)
625 If you have a controller with this interface, say Y here.
629 config MMC_SDHCI_SPEAR
630 bool "SDHCI support on ST SPEAr platform"
633 This selects the Secure Digital Host Controller Interface (SDHCI)
634 often referrered to as the HSMMC block in some of the ST SPEAR range
637 If you have a controller with this interface, say Y here.
642 bool "SDHCI support for STMicroelectronics SoC"
643 depends on MMC_SDHCI && OF_CONTROL
645 This selects the Secure Digital Host Controller Interface (SDHCI)
646 on STMicroelectronics STiH410 SoC.
648 config MMC_SDHCI_XENON
649 bool "SDHCI support for the Xenon SDHCI controller"
650 depends on MMC_SDHCI && DM_MMC && OF_CONTROL
652 Support for Xenon SDHCI host controller on Marvell Armada 3700
653 7k/8k ARM SoCs platforms
655 If you have a controller with this interface, say Y here.
659 config MMC_SDHCI_TANGIER
660 bool "Tangier SDHCI controller support"
661 depends on DM_MMC && BLK
664 This selects support for SDHCI controller on Tanginer
665 SoC. Note that this controller does not sit on PCI bus and,
666 hence, cannot be enumerated by standard PCI means.
668 If you're using an Intel Tangier SoC (available on Intel
669 Edison board), say Y here.
673 config MMC_SDHCI_TEGRA
674 bool "SDHCI platform support for the Tegra SD/MMC Controller"
675 depends on ARCH_TEGRA
679 This selects the Tegra SD/MMC controller. If you have a Tegra
680 platform with SD or MMC devices, say Y here.
684 config TEGRA124_MMC_DISABLE_EXT_LOOPBACK
685 bool "Disable external clock loopback"
686 depends on MMC_SDHCI_TEGRA && TEGRA124
688 Disable the external clock loopback and use the internal one on SDMMC3
689 as per the SDMMC_VENDOR_MISC_CNTRL_0 register's SDMMC_SPARE1 bits
690 being set to 0xfffd according to the TRM.
692 TODO(marcel.ziswiler@toradex.com): Move to device tree controlled
693 approach once proper kernel integration made it mainline.
695 config MMC_SDHCI_ZYNQ
696 bool "Arasan SDHCI controller support"
697 depends on DM_MMC && OF_CONTROL && BLK
700 Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform
702 config ZYNQ_SDHCI_MAX_FREQ
703 int "Set the maximum frequency of the controller"
704 depends on MMC_SDHCI_ZYNQ
706 Set the maximum frequency of the controller.
708 config ZYNQ_SDHCI_MIN_FREQ
709 int "Set the minimum frequency of the controller"
710 depends on MMC_SDHCI_ZYNQ
713 Set the minimum frequency of the controller.
715 config ZYNQ_HISPD_BROKEN
716 bool "High speed broken for Zynq SDHCI controller"
717 depends on MMC_SDHCI_ZYNQ
719 Set if high speed mode is broken.
722 bool "Allwinner sunxi SD/MMC Host Controller support"
723 depends on ARCH_SUNXI && !UART0_PORT_F
726 This selects support for the SD/MMC Host Controller on
727 Allwinner sunxi SoCs.
729 config MMC_SUNXI_HAS_NEW_MODE
733 config MMC_SUNXI_HAS_MODE_SWITCH
738 bool "MMC support for OpenPiton SoC"
739 depends on DM_MMC && BLK
741 This selects support for the SD host controller on OpenPiton SoC.
742 Note that this SD controller directly exposes the contents of the
743 SD card as memory mapped, so there is no manual configuration
746 config GENERIC_ATMEL_MCI
747 bool "Atmel Multimedia Card Interface support"
748 depends on DM_MMC && BLK && ARCH_AT91
750 This enables support for Atmel High Speed Multimedia Card Interface
751 (HSMCI), which supports the MultiMedia Card (MMC) Specification V4.3,
752 the SD Memory Card Specification V2.0, the SDIO V2.0 specification
756 bool "STMicroelectronics STM32H7 SD/MMC Host Controller support"
757 depends on DM_MMC && BLK && OF_CONTROL
759 This selects support for the SD/MMC controller on STM32H7 SoCs.
760 If you have a board based on such a SoC and with a SD/MMC slot,
764 bool "Ftsdc010 SD/MMC controller Support"
766 This SD/MMC controller is present in Andestech SoCs which is based on Faraday IP.
769 bool "Support ftsdc010 sdio"
772 This can enable ftsdc010 sdio function.
775 bool "MediaTek SD/MMC Card Interface support"
776 depends on ARCH_MEDIATEK || ARCH_MTMIPS
777 depends on BLK && DM_MMC
778 depends on OF_CONTROL
780 This selects the MediaTek(R) Secure digital and Multimedia card Interface.
781 If you have a machine with a integrated SD/MMC card reader, say Y or M here.
782 This is needed if support for any SD/SDIO/MMC devices is required.
788 bool "Freescale/NXP eSDHC controller support"
790 This selects support for the eSDHC (Enhanced Secure Digital Host
791 Controller) found on numerous Freescale/NXP SoCs.
793 config FSL_ESDHC_SUPPORT_ADMA2
794 bool "enable ADMA2 support"
796 select MMC_SDHCI_ADMA_HELPERS
798 This enables support for the ADMA2 transfer mode. If supported by the
799 eSDHC it will allow 64bit DMA addresses.
801 config FSL_ESDHC_33V_IO_RELIABILITY_WORKAROUND
802 bool "enable eSDHC workaround for 3.3v IO reliability issue"
803 depends on FSL_ESDHC && DM_MMC
805 When eSDHC operates at 3.3v, damage can accumulate in an internal
806 level shifter at a higher than expected rate. The faster the interface
807 runs, the more damage accumulates. This issue now is found on LX2160A
808 eSDHC1 for only SD card. The hardware workaround is recommended to use
809 an on-board level shifter that is 1.8v on SoC side and 3.3v on SD card
810 side. For boards without hardware workaround, this option could be
811 enabled, ensuring 1.8v IO voltage and disabling eSDHC if no card.
812 This option assumes no hotplug, and u-boot has to make all the way to
813 to linux to use 1.8v UHS-I speed mode if has card.
815 config FSL_ESDHC_VS33_NOT_SUPPORT
816 bool "3.3V power supply not supported"
819 For eSDHC, power supply is through peripheral circuit. 3.3V support is
820 common. Select this if 3.3V power supply not supported.
823 bool "Freescale/NXP i.MX eSDHC controller support"
825 This selects support for the i.MX eSDHC (Enhanced Secure Digital Host
826 Controller) found on numerous Freescale/NXP SoCs.
829 bool "Freescale/NXP i.MX uSDHC controller support"
830 depends on MX6 || MX7 ||ARCH_MX7ULP || IMX8 || IMX8M || IMX8ULP || IMXRT
833 This enables the Ultra Secured Digital Host Controller enhancements
837 config SYS_FSL_ERRATUM_ESDHC111
840 config SYS_FSL_ERRATUM_ESDHC13
843 config SYS_FSL_ERRATUM_ESDHC135
846 config SYS_FSL_ERRATUM_ESDHC_A001
849 config SYS_FSL_ERRATUM_A011334
852 config SYS_FSL_ESDHC_UNRELIABLE_PULSE_DETECTION_WORKAROUND