1 # SPDX-License-Identifier: GPL-2.0-only
3 # Touchscreen driver configuration
5 menuconfig INPUT_TOUCHSCREEN
8 Say Y here, and a list of supported touchscreens will be displayed.
9 This option doesn't affect the kernel.
15 config TOUCHSCREEN_88PM860X
16 tristate "Marvell 88PM860x touchscreen"
17 depends on MFD_88PM860X
19 Say Y here if you have a 88PM860x PMIC and want to enable
20 support for the built-in touchscreen.
24 To compile this driver as a module, choose M here: the
25 module will be called 88pm860x-ts.
27 config TOUCHSCREEN_ADS7846
28 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
30 depends on HWMON = n || HWMON
32 Say Y here if you have a touchscreen interface using the
33 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
34 and your board-specific setup code includes that in its
37 If HWMON is selected, and the driver is told the reference voltage
38 on your board, you will also get hwmon interfaces for the voltage
39 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
41 If unsure, say N (but it's safe to say "Y").
43 To compile this driver as a module, choose M here: the
44 module will be called ads7846.
46 config TOUCHSCREEN_AD7877
47 tristate "AD7877 based touchscreens"
50 Say Y here if you have a touchscreen interface using the
51 AD7877 controller, and your board-specific initialization
52 code includes that in its table of SPI devices.
54 If unsure, say N (but it's safe to say "Y").
56 To compile this driver as a module, choose M here: the
57 module will be called ad7877.
59 config TOUCHSCREEN_AD7879
60 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
62 Say Y here if you want to support a touchscreen interface using
63 the AD7879-1/AD7889-1 controller.
65 You should select a bus connection too.
67 To compile this driver as a module, choose M here: the
68 module will be called ad7879.
70 config TOUCHSCREEN_AD7879_I2C
71 tristate "support I2C bus connection"
72 depends on TOUCHSCREEN_AD7879 && I2C
75 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
77 To compile this driver as a module, choose M here: the
78 module will be called ad7879-i2c.
80 config TOUCHSCREEN_AD7879_SPI
81 tristate "support SPI bus connection"
82 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
85 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
87 If unsure, say N (but it's safe to say "Y").
89 To compile this driver as a module, choose M here: the
90 module will be called ad7879-spi.
92 config TOUCHSCREEN_ADC
93 tristate "Generic ADC based resistive touchscreen"
98 Say Y here if you want to use the generic ADC
99 resistive touchscreen driver.
101 If unsure, say N (but it's safe to say "Y").
103 To compile this driver as a module, choose M here: the
104 module will be called resistive-adc-touch.ko.
106 config TOUCHSCREEN_AR1021_I2C
107 tristate "Microchip AR1020/1021 i2c touchscreen"
110 Say Y here if you have the Microchip AR1020 or AR1021 touchscreen
111 controller chip in your system.
115 To compile this driver as a module, choose M here: the
116 module will be called ar1021_i2c.
118 config TOUCHSCREEN_ATMEL_MXT
119 tristate "Atmel mXT I2C Touchscreen"
123 Say Y here if you have Atmel mXT series I2C touchscreen,
124 such as AT42QT602240/ATMXT224, connected to your system.
128 To compile this driver as a module, choose M here: the
129 module will be called atmel_mxt_ts.
131 config TOUCHSCREEN_ATMEL_MXT_T37
132 bool "Support T37 Diagnostic Data"
133 depends on TOUCHSCREEN_ATMEL_MXT
134 depends on VIDEO_V4L2=y || (TOUCHSCREEN_ATMEL_MXT=m && VIDEO_V4L2=m)
135 select VIDEOBUF2_VMALLOC
137 Say Y here if you want support to output data from the T37
138 Diagnostic Data object using a V4L device.
140 config TOUCHSCREEN_AUO_PIXCIR
141 tristate "AUO in-cell touchscreen using Pixcir ICs"
143 depends on GPIOLIB || COMPILE_TEST
145 Say Y here if you have a AUO display with in-cell touchscreen
150 To compile this driver as a module, choose M here: the
151 module will be called auo-pixcir-ts.
153 config TOUCHSCREEN_BU21013
154 tristate "BU21013 based touch panel controllers"
157 Say Y here if you have a bu21013 touchscreen connected to
162 To compile this driver as a module, choose M here: the
163 module will be called bu21013_ts.
165 config TOUCHSCREEN_BU21029
166 tristate "Rohm BU21029 based touch panel controllers"
169 Say Y here if you have a Rohm BU21029 touchscreen controller
170 connected to your system.
174 To compile this driver as a module, choose M here: the
175 module will be called bu21029_ts.
177 config TOUCHSCREEN_CHIPONE_ICN8318
178 tristate "chipone icn8318 touchscreen controller"
179 depends on GPIOLIB || COMPILE_TEST
183 Say Y here if you have a ChipOne icn8318 based I2C touchscreen.
187 To compile this driver as a module, choose M here: the
188 module will be called chipone_icn8318.
190 config TOUCHSCREEN_CHIPONE_ICN8505
191 tristate "chipone icn8505 touchscreen controller"
192 depends on I2C && ACPI
194 Say Y here if you have a ChipOne icn8505 based I2C touchscreen.
198 To compile this driver as a module, choose M here: the
199 module will be called chipone_icn8505.
201 config TOUCHSCREEN_CY8CTMA140
202 tristate "cy8ctma140 touchscreen"
205 Say Y here if you have a Cypress CY8CTMA140 capacitive
206 touchscreen also just known as "TMA140"
210 To compile this driver as a module, choose M here: the
211 module will be called cy8ctma140.
213 config TOUCHSCREEN_CY8CTMG110
214 tristate "cy8ctmg110 touchscreen"
216 depends on GPIOLIB || COMPILE_TEST
218 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
223 To compile this driver as a module, choose M here: the
224 module will be called cy8ctmg110_ts.
226 config TOUCHSCREEN_CYTTSP_CORE
227 tristate "Cypress TTSP touchscreen"
229 Say Y here if you have a touchscreen using controller from
230 the Cypress TrueTouch(tm) Standard Product family connected
231 to your system. You will also need to select appropriate
232 bus connection below.
236 To compile this driver as a module, choose M here: the
237 module will be called cyttsp_core.
239 config TOUCHSCREEN_CYTTSP_I2C
240 tristate "support I2C bus connection"
241 depends on TOUCHSCREEN_CYTTSP_CORE && I2C
243 Say Y here if the touchscreen is connected via I2C bus.
245 To compile this driver as a module, choose M here: the
246 module will be called cyttsp_i2c.
248 config TOUCHSCREEN_CYTTSP_SPI
249 tristate "support SPI bus connection"
250 depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
252 Say Y here if the touchscreen is connected via SPI bus.
254 To compile this driver as a module, choose M here: the
255 module will be called cyttsp_spi.
257 config TOUCHSCREEN_CYTTSP4_CORE
258 tristate "Cypress TrueTouch Gen4 Touchscreen Driver"
260 Core driver for Cypress TrueTouch(tm) Standard Product
261 Generation4 touchscreen controllers.
263 Say Y here if you have a Cypress Gen4 touchscreen.
267 To compile this driver as a module, choose M here.
269 config TOUCHSCREEN_CYTTSP4_I2C
270 tristate "support I2C bus connection"
271 depends on TOUCHSCREEN_CYTTSP4_CORE && I2C
273 Say Y here if the touchscreen is connected via I2C bus.
275 To compile this driver as a module, choose M here: the
276 module will be called cyttsp4_i2c.
278 config TOUCHSCREEN_CYTTSP4_SPI
279 tristate "support SPI bus connection"
280 depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER
282 Say Y here if the touchscreen is connected via SPI bus.
284 To compile this driver as a module, choose M here: the
285 module will be called cyttsp4_spi.
287 config TOUCHSCREEN_DA9034
288 tristate "Touchscreen support for Dialog Semiconductor DA9034"
289 depends on PMIC_DA903X
292 Say Y here to enable the support for the touchscreen found
293 on Dialog Semiconductor DA9034 PMIC.
297 To compile this driver as a module, choose M here: the
298 module will be called da9034-ts.
300 config TOUCHSCREEN_DA9052
301 tristate "Dialog DA9052/DA9053 TSI"
302 depends on PMIC_DA9052
304 Say Y here to support the touchscreen found on Dialog Semiconductor
305 DA9052-BC and DA9053-AA/Bx PMICs.
309 To compile this driver as a module, choose M here: the
310 module will be called da9052_tsi.
312 config TOUCHSCREEN_DYNAPRO
313 tristate "Dynapro serial touchscreen"
316 Say Y here if you have a Dynapro serial touchscreen connected to
321 To compile this driver as a module, choose M here: the
322 module will be called dynapro.
324 config TOUCHSCREEN_HAMPSHIRE
325 tristate "Hampshire serial touchscreen"
328 Say Y here if you have a Hampshire serial touchscreen connected to
333 To compile this driver as a module, choose M here: the
334 module will be called hampshire.
336 config TOUCHSCREEN_EETI
337 tristate "EETI touchscreen panel support"
340 Say Y here to enable support for I2C connected EETI touch panels.
342 To compile this driver as a module, choose M here: the
343 module will be called eeti_ts.
345 config TOUCHSCREEN_EGALAX
346 tristate "EETI eGalax multi-touch panel support"
349 Say Y here to enable support for I2C connected EETI
350 eGalax multi-touch panels.
352 To compile this driver as a module, choose M here: the
353 module will be called egalax_ts.
355 config TOUCHSCREEN_EGALAX_SERIAL
356 tristate "EETI eGalax serial touchscreen"
359 Say Y here to enable support for serial connected EETI
362 To compile this driver as a module, choose M here: the
363 module will be called egalax_ts_serial.
365 config TOUCHSCREEN_EXC3000
366 tristate "EETI EXC3000 multi-touch panel support"
369 Say Y here to enable support for I2C connected EETI
370 EXC3000 multi-touch panels.
372 To compile this driver as a module, choose M here: the
373 module will be called exc3000.
375 config TOUCHSCREEN_FUJITSU
376 tristate "Fujitsu serial touchscreen"
379 Say Y here if you have the Fujitsu touchscreen (such as one
380 installed in Lifebook P series laptop) connected to your
385 To compile this driver as a module, choose M here: the
386 module will be called fujitsu-ts.
388 config TOUCHSCREEN_GOODIX
389 tristate "Goodix I2C touchscreen"
391 depends on GPIOLIB || COMPILE_TEST
393 Say Y here if you have the Goodix touchscreen (such as one
394 installed in Onda v975w tablets) connected to your
395 system. It also supports 5-finger chip models, which can be
396 found on ARM tablets, like Wexler TAB7200 and MSI Primo73.
400 To compile this driver as a module, choose M here: the
401 module will be called goodix.
403 config TOUCHSCREEN_HIDEEP
404 tristate "HiDeep Touch IC"
407 Say Y here if you have a touchscreen using HiDeep.
411 To compile this driver as a module, choose M here : the
412 module will be called hideep_ts.
414 config TOUCHSCREEN_HYCON_HY46XX
415 tristate "Hycon hy46xx touchscreen support"
418 Say Y here if you have a touchscreen using Hycon hy46xx
422 To compile this driver as a module, choose M here: the
423 module will be called hycon-hy46xx.
425 config TOUCHSCREEN_ILI210X
426 tristate "Ilitek ILI210X based touchscreen"
429 Say Y here if you have a ILI210X based touchscreen
430 controller. This driver supports models ILI2102,
431 ILI2102s, ILI2103, ILI2103s and ILI2105.
432 Such kind of chipsets can be found in Amazon Kindle Fire
437 To compile this driver as a module, choose M here: the
438 module will be called ili210x.
440 config TOUCHSCREEN_ILITEK
441 tristate "Ilitek I2C 213X/23XX/25XX/Lego Series Touch ICs"
444 Say Y here if you have touchscreen with ILITEK touch IC,
445 it supports 213X/23XX/25XX and other Lego series.
449 To compile this driver as a module, choose M here: the
450 module will be called ilitek_ts_i2c.
452 config TOUCHSCREEN_IPROC
453 tristate "IPROC touch panel driver support"
454 depends on ARCH_BCM_IPROC || COMPILE_TEST
456 Say Y here if you want to add support for the IPROC touch
457 controller to your system.
461 To compile this driver as a module, choose M here: the
462 module will be called bcm_iproc_tsc.
464 config TOUCHSCREEN_S3C2410
465 tristate "Samsung S3C2410/generic touchscreen input driver"
466 depends on ARCH_S3C24XX || SAMSUNG_DEV_TS
469 Say Y here if you have the s3c2410 touchscreen.
473 To compile this driver as a module, choose M here: the
474 module will be called s3c2410_ts.
476 config TOUCHSCREEN_S6SY761
477 tristate "Samsung S6SY761 Touchscreen driver"
480 Say Y if you have the Samsung S6SY761 driver
484 To compile this driver as module, choose M here: the
485 module will be called s6sy761.
487 config TOUCHSCREEN_GUNZE
488 tristate "Gunze AHL-51S touchscreen"
491 Say Y here if you have the Gunze AHL-51 touchscreen connected to
496 To compile this driver as a module, choose M here: the
497 module will be called gunze.
499 config TOUCHSCREEN_EKTF2127
500 tristate "Elan eKTF2127 I2C touchscreen"
503 Say Y here if you have an Elan eKTF2127 touchscreen
504 connected to your system.
508 To compile this driver as a module, choose M here: the
509 module will be called ektf2127.
511 config TOUCHSCREEN_ELAN
512 tristate "Elan eKTH I2C touchscreen"
515 Say Y here if you have an Elan eKTH I2C touchscreen
516 connected to your system.
520 To compile this driver as a module, choose M here: the
521 module will be called elants_i2c.
523 config TOUCHSCREEN_ELO
524 tristate "Elo serial touchscreens"
527 Say Y here if you have an Elo serial touchscreen connected to
532 To compile this driver as a module, choose M here: the
533 module will be called elo.
535 config TOUCHSCREEN_WACOM_W8001
536 tristate "Wacom W8001 penabled serial touchscreen"
539 Say Y here if you have an Wacom W8001 penabled serial touchscreen
540 connected to your system.
544 To compile this driver as a module, choose M here: the
545 module will be called wacom_w8001.
547 config TOUCHSCREEN_WACOM_I2C
548 tristate "Wacom Tablet support (I2C)"
551 Say Y here if you want to use the I2C version of the Wacom
556 To compile this driver as a module, choose M here: the module
557 will be called wacom_i2c.
559 config TOUCHSCREEN_LPC32XX
560 tristate "LPC32XX touchscreen controller"
561 depends on ARCH_LPC32XX
563 Say Y here if you have a LPC32XX device and want
564 to support the built-in touchscreen.
566 To compile this driver as a module, choose M here: the
567 module will be called lpc32xx_ts.
569 config TOUCHSCREEN_MAX11801
570 tristate "MAX11801 based touchscreens"
573 Say Y here if you have a MAX11801 based touchscreen
578 To compile this driver as a module, choose M here: the
579 module will be called max11801_ts.
581 config TOUCHSCREEN_MCS5000
582 tristate "MELFAS MCS-5000 touchscreen"
585 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
590 To compile this driver as a module, choose M here: the
591 module will be called mcs5000_ts.
593 config TOUCHSCREEN_MMS114
594 tristate "MELFAS MMS114 touchscreen"
597 Say Y here if you have the MELFAS MMS114 touchscreen controller
602 To compile this driver as a module, choose M here: the
603 module will be called mms114.
605 config TOUCHSCREEN_MELFAS_MIP4
606 tristate "MELFAS MIP4 Touchscreen"
609 Say Y here if you have a MELFAS MIP4 Touchscreen device.
613 To compile this driver as a module, choose M here:
614 the module will be called melfas_mip4.
616 config TOUCHSCREEN_MSG2638
617 tristate "MStar msg2638 touchscreen support"
619 depends on GPIOLIB || COMPILE_TEST
621 Say Y here if you have an I2C touchscreen using MStar msg2638.
625 To compile this driver as a module, choose M here: the
626 module will be called msg2638.
628 config TOUCHSCREEN_MTOUCH
629 tristate "MicroTouch serial touchscreens"
632 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
637 To compile this driver as a module, choose M here: the
638 module will be called mtouch.
640 config TOUCHSCREEN_IMX6UL_TSC
641 tristate "Freescale i.MX6UL touchscreen controller"
642 depends on ((OF && GPIOLIB) || COMPILE_TEST) && HAS_IOMEM
644 Say Y here if you have a Freescale i.MX6UL, and want to
645 use the internal touchscreen controller.
649 To compile this driver as a module, choose M here: the
650 module will be called imx6ul_tsc.
652 config TOUCHSCREEN_INEXIO
653 tristate "iNexio serial touchscreens"
656 Say Y here if you have an iNexio serial touchscreen connected to
661 To compile this driver as a module, choose M here: the
662 module will be called inexio.
664 config TOUCHSCREEN_MK712
665 tristate "ICS MicroClock MK712 touchscreen"
667 Say Y here if you have the ICS MicroClock MK712 touchscreen
668 controller chip in your system.
672 To compile this driver as a module, choose M here: the
673 module will be called mk712.
675 config TOUCHSCREEN_HP600
676 tristate "HP Jornada 6xx touchscreen"
677 depends on SH_HP6XX && SH_ADC
679 Say Y here if you have a HP Jornada 620/660/680/690 and want to
680 support the built-in touchscreen.
682 To compile this driver as a module, choose M here: the
683 module will be called hp680_ts_input.
685 config TOUCHSCREEN_HP7XX
686 tristate "HP Jornada 7xx touchscreen"
687 depends on SA1100_JORNADA720_SSP
689 Say Y here if you have a HP Jornada 710/720/728 and want
690 to support the built-in touchscreen.
692 To compile this driver as a module, choose M here: the
693 module will be called jornada720_ts.
695 config TOUCHSCREEN_IPAQ_MICRO
696 tristate "HP iPAQ Atmel Micro ASIC touchscreen"
697 depends on MFD_IPAQ_MICRO
699 Say Y here to enable support for the touchscreen attached to
700 the Atmel Micro peripheral controller on iPAQ h3100/h3600/h3700
704 To compile this driver as a module, choose M here: the
705 module will be called ipaq-micro-ts.
707 config TOUCHSCREEN_HTCPEN
708 tristate "HTC Shift X9500 touchscreen"
711 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
712 Clio / Shangrila and want to support the built-in touchscreen.
716 To compile this driver as a module, choose M here: the
717 module will be called htcpen.
719 config TOUCHSCREEN_PENMOUNT
720 tristate "Penmount serial touchscreen"
723 Say Y here if you have a Penmount serial touchscreen connected to
728 To compile this driver as a module, choose M here: the
729 module will be called penmount.
731 config TOUCHSCREEN_EDT_FT5X06
732 tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
735 Say Y here if you have an EDT "Polytouch" touchscreen based
736 on the FocalTech FT5x06 family of controllers connected to
741 To compile this driver as a module, choose M here: the
742 module will be called edt-ft5x06.
744 config TOUCHSCREEN_RASPBERRYPI_FW
745 tristate "Raspberry Pi's firmware base touch screen support"
746 depends on RASPBERRYPI_FIRMWARE || (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)
748 Say Y here if you have the official Raspberry Pi 7 inch screen on
753 To compile this driver as a module, choose M here: the
754 module will be called raspberrypi-ts.
756 config TOUCHSCREEN_MIGOR
757 tristate "Renesas MIGO-R touchscreen"
758 depends on (SH_MIGOR || COMPILE_TEST) && I2C
760 Say Y here to enable MIGO-R touchscreen support.
764 To compile this driver as a module, choose M here: the
765 module will be called migor_ts.
767 config TOUCHSCREEN_TOUCHRIGHT
768 tristate "Touchright serial touchscreen"
771 Say Y here if you have a Touchright serial touchscreen connected to
776 To compile this driver as a module, choose M here: the
777 module will be called touchright.
779 config TOUCHSCREEN_TOUCHWIN
780 tristate "Touchwin serial touchscreen"
783 Say Y here if you have a Touchwin serial touchscreen connected to
788 To compile this driver as a module, choose M here: the
789 module will be called touchwin.
791 config TOUCHSCREEN_TI_AM335X_TSC
792 tristate "TI Touchscreen Interface"
793 depends on MFD_TI_AM335X_TSCADC
795 Say Y here if you have 4/5/8 wire touchscreen controller
796 to be connected to the ADC controller on your TI AM335x SoC.
800 To compile this driver as a module, choose M here: the
801 module will be called ti_am335x_tsc.
803 config TOUCHSCREEN_UCB1400
804 tristate "Philips UCB1400 touchscreen"
806 depends on UCB1400_CORE
808 This enables support for the Philips UCB1400 touchscreen interface.
809 The UCB1400 is an AC97 audio codec. The touchscreen interface
810 will be initialized only after the ALSA subsystem has been
811 brought up and the UCB1400 detected. You therefore have to
812 configure ALSA support as well (either built-in or modular,
813 independently of whether this driver is itself built-in or
814 modular) for this driver to work.
816 To compile this driver as a module, choose M here: the
817 module will be called ucb1400_ts.
819 config TOUCHSCREEN_PIXCIR
820 tristate "PIXCIR I2C touchscreens"
823 Say Y here if you have a pixcir i2c touchscreen
828 To compile this driver as a module, choose M here: the
829 module will be called pixcir_i2c_ts.
831 config TOUCHSCREEN_WDT87XX_I2C
832 tristate "Weida HiTech I2C touchscreen"
835 Say Y here if you have a Weida WDT87XX I2C touchscreen
836 connected to your system.
840 To compile this driver as a module, choose M here: the
841 module will be called wdt87xx_i2c.
843 config TOUCHSCREEN_WM831X
844 tristate "Support for WM831x touchscreen controllers"
845 depends on MFD_WM831X
847 This enables support for the touchscreen controller on the WM831x
850 To compile this driver as a module, choose M here: the
851 module will be called wm831x-ts.
853 config TOUCHSCREEN_WM97XX
854 tristate "Support for WM97xx AC97 touchscreen controllers"
855 depends on AC97_BUS || AC97_BUS_NEW
857 Say Y here if you have a Wolfson Microelectronics WM97xx
858 touchscreen connected to your system. Note that this option
859 only enables core driver, you will also need to select
860 support for appropriate chip below.
864 To compile this driver as a module, choose M here: the
865 module will be called wm97xx-ts.
867 config TOUCHSCREEN_WM9705
868 bool "WM9705 Touchscreen interface support"
869 depends on TOUCHSCREEN_WM97XX
872 Say Y here to enable support for the Wolfson Microelectronics
873 WM9705 touchscreen controller.
875 config TOUCHSCREEN_WM9712
876 bool "WM9712 Touchscreen interface support"
877 depends on TOUCHSCREEN_WM97XX
880 Say Y here to enable support for the Wolfson Microelectronics
881 WM9712 touchscreen controller.
883 config TOUCHSCREEN_WM9713
884 bool "WM9713 Touchscreen interface support"
885 depends on TOUCHSCREEN_WM97XX
888 Say Y here to enable support for the Wolfson Microelectronics
889 WM9713 touchscreen controller.
891 config TOUCHSCREEN_WM97XX_MAINSTONE
892 tristate "WM97xx Mainstone/Palm accelerated touch"
893 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
895 Say Y here for support for streaming mode with WM97xx touchscreens
896 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
900 To compile this driver as a module, choose M here: the
901 module will be called mainstone-wm97xx.
903 config TOUCHSCREEN_WM97XX_ZYLONITE
904 tristate "Zylonite accelerated touch"
905 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
906 select TOUCHSCREEN_WM9713
908 Say Y here for support for streaming mode with the touchscreen
913 To compile this driver as a module, choose M here: the
914 module will be called zylonite-wm97xx.
916 config TOUCHSCREEN_USB_COMPOSITE
917 tristate "USB Touchscreen Driver"
918 depends on USB_ARCH_HAS_HCD
921 USB Touchscreen driver for:
922 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
923 - PanJit TouchSet USB
924 - 3M MicroTouch USB (EX II series)
926 - some other eTurboTouch
929 - IRTOUCHSYSTEMS/UNITOP
931 - GoTop Super_Q2/GogoPen/PenPower tablets
932 - JASTEC USB Touch Controller/DigiTech DTR-02U
933 - Zytronic controllers
934 - Elo TouchSystems 2700 IntelliTouch
935 - EasyTouch USB Touch Controller from Data Modul
936 - e2i (Mimo monitors)
938 Have a look at <http://linux.chapter7.ch/touchkit/> for
939 a usage description and the required user-space stuff.
941 To compile this driver as a module, choose M here: the
942 module will be called usbtouchscreen.
944 config TOUCHSCREEN_MXS_LRADC
945 tristate "Freescale i.MX23/i.MX28 LRADC touchscreen"
946 depends on MFD_MXS_LRADC
948 Say Y here if you have a touchscreen connected to the low-resolution
949 analog-to-digital converter (LRADC) on an i.MX23 or i.MX28 processor.
951 To compile this driver as a module, choose M here: the module will be
954 config TOUCHSCREEN_MX25
955 tristate "Freescale i.MX25 touchscreen input driver"
956 depends on MFD_MX25_TSADC
958 Enable support for touchscreen connected to your i.MX25.
960 To compile this driver as a module, choose M here: the
961 module will be called fsl-imx25-tcq.
963 config TOUCHSCREEN_MC13783
964 tristate "Freescale MC13783 touchscreen input driver"
965 depends on MFD_MC13XXX
967 Say Y here if you have an Freescale MC13783 PMIC on your
968 board and want to use its touchscreen
972 To compile this driver as a module, choose M here: the
973 module will be called mc13783_ts.
975 config TOUCHSCREEN_USB_EGALAX
977 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
978 depends on TOUCHSCREEN_USB_COMPOSITE
980 config TOUCHSCREEN_USB_PANJIT
982 bool "PanJit device support" if EXPERT
983 depends on TOUCHSCREEN_USB_COMPOSITE
985 config TOUCHSCREEN_USB_3M
987 bool "3M/Microtouch EX II series device support" if EXPERT
988 depends on TOUCHSCREEN_USB_COMPOSITE
990 config TOUCHSCREEN_USB_ITM
992 bool "ITM device support" if EXPERT
993 depends on TOUCHSCREEN_USB_COMPOSITE
995 config TOUCHSCREEN_USB_ETURBO
997 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
998 depends on TOUCHSCREEN_USB_COMPOSITE
1000 config TOUCHSCREEN_USB_GUNZE
1002 bool "Gunze AHL61 device support" if EXPERT
1003 depends on TOUCHSCREEN_USB_COMPOSITE
1005 config TOUCHSCREEN_USB_DMC_TSC10
1007 bool "DMC TSC-10/25 device support" if EXPERT
1008 depends on TOUCHSCREEN_USB_COMPOSITE
1010 config TOUCHSCREEN_USB_IRTOUCH
1012 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
1013 depends on TOUCHSCREEN_USB_COMPOSITE
1015 config TOUCHSCREEN_USB_IDEALTEK
1017 bool "IdealTEK URTC1000 device support" if EXPERT
1018 depends on TOUCHSCREEN_USB_COMPOSITE
1020 config TOUCHSCREEN_USB_GENERAL_TOUCH
1022 bool "GeneralTouch Touchscreen device support" if EXPERT
1023 depends on TOUCHSCREEN_USB_COMPOSITE
1025 config TOUCHSCREEN_USB_GOTOP
1027 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
1028 depends on TOUCHSCREEN_USB_COMPOSITE
1030 config TOUCHSCREEN_USB_JASTEC
1032 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
1033 depends on TOUCHSCREEN_USB_COMPOSITE
1035 config TOUCHSCREEN_USB_ELO
1037 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
1038 depends on TOUCHSCREEN_USB_COMPOSITE
1040 config TOUCHSCREEN_USB_E2I
1042 bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT
1043 depends on TOUCHSCREEN_USB_COMPOSITE
1045 config TOUCHSCREEN_USB_ZYTRONIC
1047 bool "Zytronic controller" if EXPERT
1048 depends on TOUCHSCREEN_USB_COMPOSITE
1050 config TOUCHSCREEN_USB_ETT_TC45USB
1052 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
1053 depends on TOUCHSCREEN_USB_COMPOSITE
1055 config TOUCHSCREEN_USB_NEXIO
1057 bool "NEXIO/iNexio device support" if EXPERT
1058 depends on TOUCHSCREEN_USB_COMPOSITE
1060 config TOUCHSCREEN_USB_EASYTOUCH
1062 bool "EasyTouch USB Touch controller device support" if EXPERT
1063 depends on TOUCHSCREEN_USB_COMPOSITE
1065 Say Y here if you have an EasyTouch USB Touch controller.
1068 config TOUCHSCREEN_TOUCHIT213
1069 tristate "Sahara TouchIT-213 touchscreen"
1072 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
1076 To compile this driver as a module, choose M here: the
1077 module will be called touchit213.
1079 config TOUCHSCREEN_TS4800
1080 tristate "TS-4800 touchscreen"
1081 depends on HAS_IOMEM && OF
1082 depends on SOC_IMX51 || COMPILE_TEST
1085 Say Y here if you have a touchscreen on a TS-4800 board.
1087 On TS-4800, the touchscreen is not handled directly by Linux but by
1092 To compile this driver as a module, choose M here: the
1093 module will be called ts4800_ts.
1095 config TOUCHSCREEN_TSC_SERIO
1096 tristate "TSC-10/25/40 serial touchscreen support"
1099 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
1104 To compile this driver as a module, choose M here: the
1105 module will be called tsc40.
1107 config TOUCHSCREEN_TSC200X_CORE
1110 config TOUCHSCREEN_TSC2004
1111 tristate "TSC2004 based touchscreens"
1114 select TOUCHSCREEN_TSC200X_CORE
1116 Say Y here if you have a TSC2004 based touchscreen.
1120 To compile this driver as a module, choose M here: the
1121 module will be called tsc2004.
1123 config TOUCHSCREEN_TSC2005
1124 tristate "TSC2005 based touchscreens"
1125 depends on SPI_MASTER
1127 select TOUCHSCREEN_TSC200X_CORE
1129 Say Y here if you have a TSC2005 based touchscreen.
1133 To compile this driver as a module, choose M here: the
1134 module will be called tsc2005.
1136 config TOUCHSCREEN_TSC2007
1137 tristate "TSC2007 based touchscreens"
1140 Say Y here if you have a TSC2007 based touchscreen.
1144 To compile this driver as a module, choose M here: the
1145 module will be called tsc2007.
1147 config TOUCHSCREEN_TSC2007_IIO
1148 bool "IIO interface for external ADC input and temperature"
1149 depends on TOUCHSCREEN_TSC2007
1150 depends on IIO=y || IIO=TOUCHSCREEN_TSC2007
1152 Saying Y here adds an iio interface to the tsc2007 which
1153 provides values for the AUX input (used for e.g. battery
1154 or ambient light monitoring), temperature and raw input
1157 config TOUCHSCREEN_PCAP
1158 tristate "Motorola PCAP touchscreen"
1161 Say Y here if you have a Motorola EZX telephone and
1162 want to enable support for the built-in touchscreen.
1164 To compile this driver as a module, choose M here: the
1165 module will be called pcap_ts.
1167 config TOUCHSCREEN_RM_TS
1168 tristate "Raydium I2C Touchscreen"
1170 depends on GPIOLIB || COMPILE_TEST
1172 Say Y here if you have Raydium series I2C touchscreen,
1173 such as RM32380, connected to your system.
1177 To compile this driver as a module, choose M here: the
1178 module will be called raydium_i2c_ts.
1180 config TOUCHSCREEN_SILEAD
1181 tristate "Silead I2C touchscreen"
1184 Say Y here if you have the Silead touchscreen connected to
1189 To compile this driver as a module, choose M here: the
1190 module will be called silead.
1192 config TOUCHSCREEN_SIS_I2C
1193 tristate "SiS 9200 family I2C touchscreen"
1196 depends on GPIOLIB || COMPILE_TEST
1198 This enables support for SiS 9200 family over I2C based touchscreens.
1202 To compile this driver as a module, choose M here: the
1203 module will be called sis_i2c.
1205 config TOUCHSCREEN_ST1232
1206 tristate "Sitronix ST1232 or ST1633 touchscreen controllers"
1209 Say Y here if you want to support the Sitronix ST1232
1210 or ST1633 touchscreen controller.
1214 To compile this driver as a module, choose M here: the
1215 module will be called st1232_ts.
1217 config TOUCHSCREEN_STMFTS
1218 tristate "STMicroelectronics STMFTS touchscreen"
1220 depends on LEDS_CLASS
1222 Say Y here if you want support for STMicroelectronics
1225 To compile this driver as a module, choose M here: the
1226 module will be called stmfts.
1228 config TOUCHSCREEN_STMPE
1229 tristate "STMicroelectronics STMPE touchscreens"
1230 depends on MFD_STMPE
1231 depends on (OF || COMPILE_TEST)
1233 Say Y here if you want support for STMicroelectronics
1234 STMPE touchscreen controllers.
1236 To compile this driver as a module, choose M here: the
1237 module will be called stmpe-ts.
1239 config TOUCHSCREEN_SUN4I
1240 tristate "Allwinner sun4i resistive touchscreen controller support"
1241 depends on ARCH_SUNXI || COMPILE_TEST
1243 depends on THERMAL || !THERMAL_OF
1245 This selects support for the resistive touchscreen controller
1246 found on Allwinner sunxi SoCs.
1248 To compile this driver as a module, choose M here: the
1249 module will be called sun4i-ts.
1251 config TOUCHSCREEN_SUR40
1252 tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
1253 depends on USB && MEDIA_USB_SUPPORT && HAS_DMA
1254 depends on VIDEO_V4L2
1255 select VIDEOBUF2_DMA_SG
1257 Say Y here if you want support for the Samsung SUR40 touchscreen
1258 (also known as Microsoft Surface 2.0 or Microsoft PixelSense).
1260 To compile this driver as a module, choose M here: the
1261 module will be called sur40.
1263 config TOUCHSCREEN_SURFACE3_SPI
1264 tristate "Ntrig/Microsoft Surface 3 SPI touchscreen"
1266 depends on GPIOLIB || COMPILE_TEST
1268 Say Y here if you have the Ntrig/Microsoft SPI touchscreen
1269 controller chip as found on the Surface 3 in your system.
1273 To compile this driver as a module, choose M here: the
1274 module will be called surface3_spi.
1276 config TOUCHSCREEN_SX8654
1277 tristate "Semtech SX8654 touchscreen"
1280 Say Y here if you have a Semtech SX8654 touchscreen controller.
1284 To compile this driver as a module, choose M here: the
1285 module will be called sx8654.
1287 config TOUCHSCREEN_TPS6507X
1288 tristate "TPS6507x based touchscreens"
1291 Say Y here if you have a TPS6507x based touchscreen
1296 To compile this driver as a module, choose M here: the
1297 module will be called tps6507x_ts.
1299 config TOUCHSCREEN_ZET6223
1300 tristate "Zeitec ZET6223 touchscreen driver"
1303 Say Y here if you have a touchscreen using Zeitec ZET6223
1307 To compile this driver as a module, choose M here: the
1308 module will be called zet6223.
1310 config TOUCHSCREEN_ZFORCE
1311 tristate "Neonode zForce infrared touchscreens"
1313 depends on GPIOLIB || COMPILE_TEST
1315 Say Y here if you have a touchscreen using the zforce
1316 infraread technology from Neonode.
1320 To compile this driver as a module, choose M here: the
1321 module will be called zforce_ts.
1323 config TOUCHSCREEN_COLIBRI_VF50
1324 tristate "Toradex Colibri on board touchscreen driver"
1325 depends on IIO && VF610_ADC
1326 depends on GPIOLIB || COMPILE_TEST
1328 Say Y here if you have a Colibri VF50 and plan to use
1329 the on-board provided 4-wire touchscreen driver.
1333 To compile this driver as a module, choose M here: the
1334 module will be called colibri_vf50_ts.
1336 config TOUCHSCREEN_ROHM_BU21023
1337 tristate "ROHM BU21023/24 Dual touch support resistive touchscreens"
1340 Say Y here if you have a touchscreen using ROHM BU21023/24.
1344 To compile this driver as a module, choose M here: the
1345 module will be called bu21023_ts.
1347 config TOUCHSCREEN_IQS5XX
1348 tristate "Azoteq IQS550/572/525 trackpad/touchscreen controller"
1351 Say Y to enable support for the Azoteq IQS550/572/525
1352 family of trackpad/touchscreen controllers.
1354 To compile this driver as a module, choose M here: the
1355 module will be called iqs5xx.
1357 config TOUCHSCREEN_ZINITIX
1358 tristate "Zinitix touchscreen support"
1361 Say Y here if you have a touchscreen using Zinitix bt541,
1362 or something similar enough.
1366 To compile this driver as a module, choose M here: the
1367 module will be called zinitix.