1 # SPDX-License-Identifier: GPL-2.0-only
3 # Touchscreen driver configuration
5 menuconfig INPUT_TOUCHSCREEN
8 Say Y here, and a list of supported touchscreens will be displayed.
9 This option doesn't affect the kernel.
15 config TOUCHSCREEN_88PM860X
16 tristate "Marvell 88PM860x touchscreen"
17 depends on MFD_88PM860X
19 Say Y here if you have a 88PM860x PMIC and want to enable
20 support for the built-in touchscreen.
24 To compile this driver as a module, choose M here: the
25 module will be called 88pm860x-ts.
27 config TOUCHSCREEN_ADS7846
28 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
30 depends on HWMON = n || HWMON
32 Say Y here if you have a touchscreen interface using the
33 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
34 and your board-specific setup code includes that in its
37 If HWMON is selected, and the driver is told the reference voltage
38 on your board, you will also get hwmon interfaces for the voltage
39 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
41 If unsure, say N (but it's safe to say "Y").
43 To compile this driver as a module, choose M here: the
44 module will be called ads7846.
46 config TOUCHSCREEN_AD7877
47 tristate "AD7877 based touchscreens"
50 Say Y here if you have a touchscreen interface using the
51 AD7877 controller, and your board-specific initialization
52 code includes that in its table of SPI devices.
54 If unsure, say N (but it's safe to say "Y").
56 To compile this driver as a module, choose M here: the
57 module will be called ad7877.
59 config TOUCHSCREEN_AD7879
60 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
62 Say Y here if you want to support a touchscreen interface using
63 the AD7879-1/AD7889-1 controller.
65 You should select a bus connection too.
67 To compile this driver as a module, choose M here: the
68 module will be called ad7879.
70 config TOUCHSCREEN_AD7879_I2C
71 tristate "support I2C bus connection"
72 depends on TOUCHSCREEN_AD7879 && I2C
75 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
77 To compile this driver as a module, choose M here: the
78 module will be called ad7879-i2c.
80 config TOUCHSCREEN_AD7879_SPI
81 tristate "support SPI bus connection"
82 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
85 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
87 If unsure, say N (but it's safe to say "Y").
89 To compile this driver as a module, choose M here: the
90 module will be called ad7879-spi.
92 config TOUCHSCREEN_ADC
93 tristate "Generic ADC based resistive touchscreen"
98 Say Y here if you want to use the generic ADC
99 resistive touchscreen driver.
101 If unsure, say N (but it's safe to say "Y").
103 To compile this driver as a module, choose M here: the
104 module will be called resistive-adc-touch.ko.
106 config TOUCHSCREEN_AR1021_I2C
107 tristate "Microchip AR1020/1021 i2c touchscreen"
110 Say Y here if you have the Microchip AR1020 or AR1021 touchscreen
111 controller chip in your system.
115 To compile this driver as a module, choose M here: the
116 module will be called ar1021_i2c.
118 config TOUCHSCREEN_ATMEL_MXT
119 tristate "Atmel mXT I2C Touchscreen"
123 Say Y here if you have Atmel mXT series I2C touchscreen,
124 such as AT42QT602240/ATMXT224, connected to your system.
128 To compile this driver as a module, choose M here: the
129 module will be called atmel_mxt_ts.
131 config TOUCHSCREEN_ATMEL_MXT_T37
132 bool "Support T37 Diagnostic Data"
133 depends on TOUCHSCREEN_ATMEL_MXT
134 depends on VIDEO_V4L2=y || (TOUCHSCREEN_ATMEL_MXT=m && VIDEO_V4L2=m)
135 select VIDEOBUF2_VMALLOC
137 Say Y here if you want support to output data from the T37
138 Diagnostic Data object using a V4L device.
140 config TOUCHSCREEN_AUO_PIXCIR
141 tristate "AUO in-cell touchscreen using Pixcir ICs"
143 depends on GPIOLIB || COMPILE_TEST
145 Say Y here if you have a AUO display with in-cell touchscreen
150 To compile this driver as a module, choose M here: the
151 module will be called auo-pixcir-ts.
153 config TOUCHSCREEN_BU21013
154 tristate "BU21013 based touch panel controllers"
157 Say Y here if you have a bu21013 touchscreen connected to
162 To compile this driver as a module, choose M here: the
163 module will be called bu21013_ts.
165 config TOUCHSCREEN_BU21029
166 tristate "Rohm BU21029 based touch panel controllers"
169 Say Y here if you have a Rohm BU21029 touchscreen controller
170 connected to your system.
174 To compile this driver as a module, choose M here: the
175 module will be called bu21029_ts.
177 config TOUCHSCREEN_CHIPONE_ICN8318
178 tristate "chipone icn8318 touchscreen controller"
179 depends on GPIOLIB || COMPILE_TEST
183 Say Y here if you have a ChipOne icn8318 based I2C touchscreen.
187 To compile this driver as a module, choose M here: the
188 module will be called chipone_icn8318.
190 config TOUCHSCREEN_CHIPONE_ICN8505
191 tristate "chipone icn8505 touchscreen controller"
192 depends on I2C && ACPI
194 Say Y here if you have a ChipOne icn8505 based I2C touchscreen.
198 To compile this driver as a module, choose M here: the
199 module will be called chipone_icn8505.
201 config TOUCHSCREEN_CY8CTMA140
202 tristate "cy8ctma140 touchscreen"
205 Say Y here if you have a Cypress CY8CTMA140 capacitive
206 touchscreen also just known as "TMA140"
210 To compile this driver as a module, choose M here: the
211 module will be called cy8ctma140.
213 config TOUCHSCREEN_CY8CTMG110
214 tristate "cy8ctmg110 touchscreen"
216 depends on GPIOLIB || COMPILE_TEST
218 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
223 To compile this driver as a module, choose M here: the
224 module will be called cy8ctmg110_ts.
226 config TOUCHSCREEN_CYTTSP_CORE
227 tristate "Cypress TTSP touchscreen"
229 Say Y here if you have a touchscreen using controller from
230 the Cypress TrueTouch(tm) Standard Product family connected
231 to your system. You will also need to select appropriate
232 bus connection below.
236 To compile this driver as a module, choose M here: the
237 module will be called cyttsp_core.
239 config TOUCHSCREEN_CYTTSP_I2C
240 tristate "support I2C bus connection"
241 depends on TOUCHSCREEN_CYTTSP_CORE && I2C
243 Say Y here if the touchscreen is connected via I2C bus.
245 To compile this driver as a module, choose M here: the
246 module will be called cyttsp_i2c.
248 config TOUCHSCREEN_CYTTSP_SPI
249 tristate "support SPI bus connection"
250 depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
252 Say Y here if the touchscreen is connected via SPI bus.
254 To compile this driver as a module, choose M here: the
255 module will be called cyttsp_spi.
257 config TOUCHSCREEN_CYTTSP4_CORE
258 tristate "Cypress TrueTouch Gen4 Touchscreen Driver"
260 Core driver for Cypress TrueTouch(tm) Standard Product
261 Generation4 touchscreen controllers.
263 Say Y here if you have a Cypress Gen4 touchscreen.
267 To compile this driver as a module, choose M here.
269 config TOUCHSCREEN_CYTTSP4_I2C
270 tristate "support I2C bus connection"
271 depends on TOUCHSCREEN_CYTTSP4_CORE && I2C
273 Say Y here if the touchscreen is connected via I2C bus.
275 To compile this driver as a module, choose M here: the
276 module will be called cyttsp4_i2c.
278 config TOUCHSCREEN_CYTTSP4_SPI
279 tristate "support SPI bus connection"
280 depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER
282 Say Y here if the touchscreen is connected via SPI bus.
284 To compile this driver as a module, choose M here: the
285 module will be called cyttsp4_spi.
287 config TOUCHSCREEN_DA9034
288 tristate "Touchscreen support for Dialog Semiconductor DA9034"
289 depends on PMIC_DA903X
292 Say Y here to enable the support for the touchscreen found
293 on Dialog Semiconductor DA9034 PMIC.
297 To compile this driver as a module, choose M here: the
298 module will be called da9034-ts.
300 config TOUCHSCREEN_DA9052
301 tristate "Dialog DA9052/DA9053 TSI"
302 depends on PMIC_DA9052
304 Say Y here to support the touchscreen found on Dialog Semiconductor
305 DA9052-BC and DA9053-AA/Bx PMICs.
309 To compile this driver as a module, choose M here: the
310 module will be called da9052_tsi.
312 config TOUCHSCREEN_DYNAPRO
313 tristate "Dynapro serial touchscreen"
316 Say Y here if you have a Dynapro serial touchscreen connected to
321 To compile this driver as a module, choose M here: the
322 module will be called dynapro.
324 config TOUCHSCREEN_HAMPSHIRE
325 tristate "Hampshire serial touchscreen"
328 Say Y here if you have a Hampshire serial touchscreen connected to
333 To compile this driver as a module, choose M here: the
334 module will be called hampshire.
336 config TOUCHSCREEN_EETI
337 tristate "EETI touchscreen panel support"
340 Say Y here to enable support for I2C connected EETI touch panels.
342 To compile this driver as a module, choose M here: the
343 module will be called eeti_ts.
345 config TOUCHSCREEN_EGALAX
346 tristate "EETI eGalax multi-touch panel support"
349 Say Y here to enable support for I2C connected EETI
350 eGalax multi-touch panels.
352 To compile this driver as a module, choose M here: the
353 module will be called egalax_ts.
355 config TOUCHSCREEN_EGALAX_SERIAL
356 tristate "EETI eGalax serial touchscreen"
359 Say Y here to enable support for serial connected EETI
362 To compile this driver as a module, choose M here: the
363 module will be called egalax_ts_serial.
365 config TOUCHSCREEN_EXC3000
366 tristate "EETI EXC3000 multi-touch panel support"
369 Say Y here to enable support for I2C connected EETI
370 EXC3000 multi-touch panels.
372 To compile this driver as a module, choose M here: the
373 module will be called exc3000.
375 config TOUCHSCREEN_FUJITSU
376 tristate "Fujitsu serial touchscreen"
379 Say Y here if you have the Fujitsu touchscreen (such as one
380 installed in Lifebook P series laptop) connected to your
385 To compile this driver as a module, choose M here: the
386 module will be called fujitsu-ts.
388 config TOUCHSCREEN_GOODIX
389 tristate "Goodix I2C touchscreen"
391 depends on GPIOLIB || COMPILE_TEST
393 Say Y here if you have the Goodix touchscreen (such as one
394 installed in Onda v975w tablets) connected to your
395 system. It also supports 5-finger chip models, which can be
396 found on ARM tablets, like Wexler TAB7200 and MSI Primo73.
400 To compile this driver as a module, choose M here: the
401 module will be called goodix.
403 config TOUCHSCREEN_GT9XX
404 tristate "Goodix touch screen gt9xx support for rockchip based platform"
407 Say Y here if you have a touchscreen interface using the
408 two goodix gt9xx, and your board-specific initialization
409 code includes that in its table of IIC devices.
413 To compile this driver as a module, choose M here: the
414 module will be called gt9xx.
416 config TOUCHSCREEN_HIDEEP
417 tristate "HiDeep Touch IC"
420 Say Y here if you have a touchscreen using HiDeep.
424 To compile this driver as a module, choose M here : the
425 module will be called hideep_ts.
427 config TOUCHSCREEN_HYCON_HY46XX
428 tristate "Hycon hy46xx touchscreen support"
431 Say Y here if you have a touchscreen using Hycon hy46xx
435 To compile this driver as a module, choose M here: the
436 module will be called hycon-hy46xx.
438 config TOUCHSCREEN_ILI210X
439 tristate "Ilitek ILI210X based touchscreen"
442 Say Y here if you have a ILI210X based touchscreen
443 controller. This driver supports models ILI2102,
444 ILI2102s, ILI2103, ILI2103s and ILI2105.
445 Such kind of chipsets can be found in Amazon Kindle Fire
450 To compile this driver as a module, choose M here: the
451 module will be called ili210x.
453 config TOUCHSCREEN_ILITEK
454 tristate "Ilitek I2C 213X/23XX/25XX/Lego Series Touch ICs"
457 Say Y here if you have touchscreen with ILITEK touch IC,
458 it supports 213X/23XX/25XX and other Lego series.
462 To compile this driver as a module, choose M here: the
463 module will be called ilitek_ts_i2c.
465 config TOUCHSCREEN_IPROC
466 tristate "IPROC touch panel driver support"
467 depends on ARCH_BCM_IPROC || COMPILE_TEST
469 Say Y here if you want to add support for the IPROC touch
470 controller to your system.
474 To compile this driver as a module, choose M here: the
475 module will be called bcm_iproc_tsc.
477 config TOUCHSCREEN_S3C2410
478 tristate "Samsung S3C2410/generic touchscreen input driver"
479 depends on ARCH_S3C24XX || SAMSUNG_DEV_TS
482 Say Y here if you have the s3c2410 touchscreen.
486 To compile this driver as a module, choose M here: the
487 module will be called s3c2410_ts.
489 config TOUCHSCREEN_S6SY761
490 tristate "Samsung S6SY761 Touchscreen driver"
493 Say Y if you have the Samsung S6SY761 driver
497 To compile this driver as module, choose M here: the
498 module will be called s6sy761.
500 config TOUCHSCREEN_GUNZE
501 tristate "Gunze AHL-51S touchscreen"
504 Say Y here if you have the Gunze AHL-51 touchscreen connected to
509 To compile this driver as a module, choose M here: the
510 module will be called gunze.
512 config TOUCHSCREEN_EKTF2127
513 tristate "Elan eKTF2127 I2C touchscreen"
516 Say Y here if you have an Elan eKTF2127 touchscreen
517 connected to your system.
521 To compile this driver as a module, choose M here: the
522 module will be called ektf2127.
524 config TOUCHSCREEN_ELAN
525 tristate "Elan eKTH I2C touchscreen"
528 Say Y here if you have an Elan eKTH I2C touchscreen
529 connected to your system.
533 To compile this driver as a module, choose M here: the
534 module will be called elants_i2c.
536 config TOUCHSCREEN_ELO
537 tristate "Elo serial touchscreens"
540 Say Y here if you have an Elo serial touchscreen connected to
545 To compile this driver as a module, choose M here: the
546 module will be called elo.
548 config TOUCHSCREEN_WACOM_W8001
549 tristate "Wacom W8001 penabled serial touchscreen"
552 Say Y here if you have an Wacom W8001 penabled serial touchscreen
553 connected to your system.
557 To compile this driver as a module, choose M here: the
558 module will be called wacom_w8001.
560 config TOUCHSCREEN_WACOM_I2C
561 tristate "Wacom Tablet support (I2C)"
564 Say Y here if you want to use the I2C version of the Wacom
569 To compile this driver as a module, choose M here: the module
570 will be called wacom_i2c.
572 config TOUCHSCREEN_LPC32XX
573 tristate "LPC32XX touchscreen controller"
574 depends on ARCH_LPC32XX
576 Say Y here if you have a LPC32XX device and want
577 to support the built-in touchscreen.
579 To compile this driver as a module, choose M here: the
580 module will be called lpc32xx_ts.
582 config TOUCHSCREEN_MAX11801
583 tristate "MAX11801 based touchscreens"
586 Say Y here if you have a MAX11801 based touchscreen
591 To compile this driver as a module, choose M here: the
592 module will be called max11801_ts.
594 config TOUCHSCREEN_MCS5000
595 tristate "MELFAS MCS-5000 touchscreen"
598 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
603 To compile this driver as a module, choose M here: the
604 module will be called mcs5000_ts.
606 config TOUCHSCREEN_MMS114
607 tristate "MELFAS MMS114 touchscreen"
610 Say Y here if you have the MELFAS MMS114 touchscreen controller
615 To compile this driver as a module, choose M here: the
616 module will be called mms114.
618 config TOUCHSCREEN_MELFAS_MIP4
619 tristate "MELFAS MIP4 Touchscreen"
622 Say Y here if you have a MELFAS MIP4 Touchscreen device.
626 To compile this driver as a module, choose M here:
627 the module will be called melfas_mip4.
629 config TOUCHSCREEN_MSG2638
630 tristate "MStar msg2638 touchscreen support"
632 depends on GPIOLIB || COMPILE_TEST
634 Say Y here if you have an I2C touchscreen using MStar msg2638.
638 To compile this driver as a module, choose M here: the
639 module will be called msg2638.
641 config TOUCHSCREEN_MTOUCH
642 tristate "MicroTouch serial touchscreens"
645 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
650 To compile this driver as a module, choose M here: the
651 module will be called mtouch.
653 config TOUCHSCREEN_IMX6UL_TSC
654 tristate "Freescale i.MX6UL touchscreen controller"
655 depends on ((OF && GPIOLIB) || COMPILE_TEST) && HAS_IOMEM
657 Say Y here if you have a Freescale i.MX6UL, and want to
658 use the internal touchscreen controller.
662 To compile this driver as a module, choose M here: the
663 module will be called imx6ul_tsc.
665 config TOUCHSCREEN_INEXIO
666 tristate "iNexio serial touchscreens"
669 Say Y here if you have an iNexio serial touchscreen connected to
674 To compile this driver as a module, choose M here: the
675 module will be called inexio.
677 config TOUCHSCREEN_MK712
678 tristate "ICS MicroClock MK712 touchscreen"
680 Say Y here if you have the ICS MicroClock MK712 touchscreen
681 controller chip in your system.
685 To compile this driver as a module, choose M here: the
686 module will be called mk712.
688 config TOUCHSCREEN_HP600
689 tristate "HP Jornada 6xx touchscreen"
690 depends on SH_HP6XX && SH_ADC
692 Say Y here if you have a HP Jornada 620/660/680/690 and want to
693 support the built-in touchscreen.
695 To compile this driver as a module, choose M here: the
696 module will be called hp680_ts_input.
698 config TOUCHSCREEN_HP7XX
699 tristate "HP Jornada 7xx touchscreen"
700 depends on SA1100_JORNADA720_SSP
702 Say Y here if you have a HP Jornada 710/720/728 and want
703 to support the built-in touchscreen.
705 To compile this driver as a module, choose M here: the
706 module will be called jornada720_ts.
708 config TOUCHSCREEN_IPAQ_MICRO
709 tristate "HP iPAQ Atmel Micro ASIC touchscreen"
710 depends on MFD_IPAQ_MICRO
712 Say Y here to enable support for the touchscreen attached to
713 the Atmel Micro peripheral controller on iPAQ h3100/h3600/h3700
717 To compile this driver as a module, choose M here: the
718 module will be called ipaq-micro-ts.
720 config TOUCHSCREEN_HTCPEN
721 tristate "HTC Shift X9500 touchscreen"
724 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
725 Clio / Shangrila and want to support the built-in touchscreen.
729 To compile this driver as a module, choose M here: the
730 module will be called htcpen.
732 config TOUCHSCREEN_PENMOUNT
733 tristate "Penmount serial touchscreen"
736 Say Y here if you have a Penmount serial touchscreen connected to
741 To compile this driver as a module, choose M here: the
742 module will be called penmount.
744 config TOUCHSCREEN_EDT_FT5X06
745 tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
748 Say Y here if you have an EDT "Polytouch" touchscreen based
749 on the FocalTech FT5x06 family of controllers connected to
754 To compile this driver as a module, choose M here: the
755 module will be called edt-ft5x06.
757 config TOUCHSCREEN_RASPBERRYPI_FW
758 tristate "Raspberry Pi's firmware base touch screen support"
759 depends on RASPBERRYPI_FIRMWARE || (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)
761 Say Y here if you have the official Raspberry Pi 7 inch screen on
766 To compile this driver as a module, choose M here: the
767 module will be called raspberrypi-ts.
769 config TOUCHSCREEN_MIGOR
770 tristate "Renesas MIGO-R touchscreen"
771 depends on (SH_MIGOR || COMPILE_TEST) && I2C
773 Say Y here to enable MIGO-R touchscreen support.
777 To compile this driver as a module, choose M here: the
778 module will be called migor_ts.
780 config TOUCHSCREEN_TOUCHRIGHT
781 tristate "Touchright serial touchscreen"
784 Say Y here if you have a Touchright serial touchscreen connected to
789 To compile this driver as a module, choose M here: the
790 module will be called touchright.
792 config TOUCHSCREEN_TOUCHWIN
793 tristate "Touchwin serial touchscreen"
796 Say Y here if you have a Touchwin serial touchscreen connected to
801 To compile this driver as a module, choose M here: the
802 module will be called touchwin.
804 config TOUCHSCREEN_TI_AM335X_TSC
805 tristate "TI Touchscreen Interface"
806 depends on MFD_TI_AM335X_TSCADC
808 Say Y here if you have 4/5/8 wire touchscreen controller
809 to be connected to the ADC controller on your TI AM335x SoC.
813 To compile this driver as a module, choose M here: the
814 module will be called ti_am335x_tsc.
816 config TOUCHSCREEN_UCB1400
817 tristate "Philips UCB1400 touchscreen"
819 depends on UCB1400_CORE
821 This enables support for the Philips UCB1400 touchscreen interface.
822 The UCB1400 is an AC97 audio codec. The touchscreen interface
823 will be initialized only after the ALSA subsystem has been
824 brought up and the UCB1400 detected. You therefore have to
825 configure ALSA support as well (either built-in or modular,
826 independently of whether this driver is itself built-in or
827 modular) for this driver to work.
829 To compile this driver as a module, choose M here: the
830 module will be called ucb1400_ts.
832 config TOUCHSCREEN_PIXCIR
833 tristate "PIXCIR I2C touchscreens"
836 Say Y here if you have a pixcir i2c touchscreen
841 To compile this driver as a module, choose M here: the
842 module will be called pixcir_i2c_ts.
844 config TOUCHSCREEN_WDT87XX_I2C
845 tristate "Weida HiTech I2C touchscreen"
848 Say Y here if you have a Weida WDT87XX I2C touchscreen
849 connected to your system.
853 To compile this driver as a module, choose M here: the
854 module will be called wdt87xx_i2c.
856 config TOUCHSCREEN_WM831X
857 tristate "Support for WM831x touchscreen controllers"
858 depends on MFD_WM831X
860 This enables support for the touchscreen controller on the WM831x
863 To compile this driver as a module, choose M here: the
864 module will be called wm831x-ts.
866 config TOUCHSCREEN_WM97XX
867 tristate "Support for WM97xx AC97 touchscreen controllers"
868 depends on AC97_BUS || AC97_BUS_NEW
870 Say Y here if you have a Wolfson Microelectronics WM97xx
871 touchscreen connected to your system. Note that this option
872 only enables core driver, you will also need to select
873 support for appropriate chip below.
877 To compile this driver as a module, choose M here: the
878 module will be called wm97xx-ts.
880 config TOUCHSCREEN_WM9705
881 bool "WM9705 Touchscreen interface support"
882 depends on TOUCHSCREEN_WM97XX
885 Say Y here to enable support for the Wolfson Microelectronics
886 WM9705 touchscreen controller.
888 config TOUCHSCREEN_WM9712
889 bool "WM9712 Touchscreen interface support"
890 depends on TOUCHSCREEN_WM97XX
893 Say Y here to enable support for the Wolfson Microelectronics
894 WM9712 touchscreen controller.
896 config TOUCHSCREEN_WM9713
897 bool "WM9713 Touchscreen interface support"
898 depends on TOUCHSCREEN_WM97XX
901 Say Y here to enable support for the Wolfson Microelectronics
902 WM9713 touchscreen controller.
904 config TOUCHSCREEN_WM97XX_MAINSTONE
905 tristate "WM97xx Mainstone/Palm accelerated touch"
906 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
908 Say Y here for support for streaming mode with WM97xx touchscreens
909 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
913 To compile this driver as a module, choose M here: the
914 module will be called mainstone-wm97xx.
916 config TOUCHSCREEN_WM97XX_ZYLONITE
917 tristate "Zylonite accelerated touch"
918 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
919 select TOUCHSCREEN_WM9713
921 Say Y here for support for streaming mode with the touchscreen
926 To compile this driver as a module, choose M here: the
927 module will be called zylonite-wm97xx.
929 config TOUCHSCREEN_USB_COMPOSITE
930 tristate "USB Touchscreen Driver"
931 depends on USB_ARCH_HAS_HCD
934 USB Touchscreen driver for:
935 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
936 - PanJit TouchSet USB
937 - 3M MicroTouch USB (EX II series)
939 - some other eTurboTouch
942 - IRTOUCHSYSTEMS/UNITOP
944 - GoTop Super_Q2/GogoPen/PenPower tablets
945 - JASTEC USB Touch Controller/DigiTech DTR-02U
946 - Zytronic controllers
947 - Elo TouchSystems 2700 IntelliTouch
948 - EasyTouch USB Touch Controller from Data Module
949 - e2i (Mimo monitors)
951 Have a look at <http://linux.chapter7.ch/touchkit/> for
952 a usage description and the required user-space stuff.
954 To compile this driver as a module, choose M here: the
955 module will be called usbtouchscreen.
957 config TOUCHSCREEN_MXS_LRADC
958 tristate "Freescale i.MX23/i.MX28 LRADC touchscreen"
959 depends on MFD_MXS_LRADC
961 Say Y here if you have a touchscreen connected to the low-resolution
962 analog-to-digital converter (LRADC) on an i.MX23 or i.MX28 processor.
964 To compile this driver as a module, choose M here: the module will be
967 config TOUCHSCREEN_MX25
968 tristate "Freescale i.MX25 touchscreen input driver"
969 depends on MFD_MX25_TSADC
971 Enable support for touchscreen connected to your i.MX25.
973 To compile this driver as a module, choose M here: the
974 module will be called fsl-imx25-tcq.
976 config TOUCHSCREEN_MC13783
977 tristate "Freescale MC13783 touchscreen input driver"
978 depends on MFD_MC13XXX
980 Say Y here if you have an Freescale MC13783 PMIC on your
981 board and want to use its touchscreen
985 To compile this driver as a module, choose M here: the
986 module will be called mc13783_ts.
988 config TOUCHSCREEN_USB_EGALAX
990 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
991 depends on TOUCHSCREEN_USB_COMPOSITE
993 config TOUCHSCREEN_USB_PANJIT
995 bool "PanJit device support" if EXPERT
996 depends on TOUCHSCREEN_USB_COMPOSITE
998 config TOUCHSCREEN_USB_3M
1000 bool "3M/Microtouch EX II series device support" if EXPERT
1001 depends on TOUCHSCREEN_USB_COMPOSITE
1003 config TOUCHSCREEN_USB_ITM
1005 bool "ITM device support" if EXPERT
1006 depends on TOUCHSCREEN_USB_COMPOSITE
1008 config TOUCHSCREEN_USB_ETURBO
1010 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
1011 depends on TOUCHSCREEN_USB_COMPOSITE
1013 config TOUCHSCREEN_USB_GUNZE
1015 bool "Gunze AHL61 device support" if EXPERT
1016 depends on TOUCHSCREEN_USB_COMPOSITE
1018 config TOUCHSCREEN_USB_DMC_TSC10
1020 bool "DMC TSC-10/25 device support" if EXPERT
1021 depends on TOUCHSCREEN_USB_COMPOSITE
1023 config TOUCHSCREEN_USB_IRTOUCH
1025 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
1026 depends on TOUCHSCREEN_USB_COMPOSITE
1028 config TOUCHSCREEN_USB_IDEALTEK
1030 bool "IdealTEK URTC1000 device support" if EXPERT
1031 depends on TOUCHSCREEN_USB_COMPOSITE
1033 config TOUCHSCREEN_USB_GENERAL_TOUCH
1035 bool "GeneralTouch Touchscreen device support" if EXPERT
1036 depends on TOUCHSCREEN_USB_COMPOSITE
1038 config TOUCHSCREEN_USB_GOTOP
1040 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
1041 depends on TOUCHSCREEN_USB_COMPOSITE
1043 config TOUCHSCREEN_USB_JASTEC
1045 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
1046 depends on TOUCHSCREEN_USB_COMPOSITE
1048 config TOUCHSCREEN_USB_ELO
1050 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
1051 depends on TOUCHSCREEN_USB_COMPOSITE
1053 config TOUCHSCREEN_USB_E2I
1055 bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT
1056 depends on TOUCHSCREEN_USB_COMPOSITE
1058 config TOUCHSCREEN_USB_ZYTRONIC
1060 bool "Zytronic controller" if EXPERT
1061 depends on TOUCHSCREEN_USB_COMPOSITE
1063 config TOUCHSCREEN_USB_ETT_TC45USB
1065 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
1066 depends on TOUCHSCREEN_USB_COMPOSITE
1068 config TOUCHSCREEN_USB_NEXIO
1070 bool "NEXIO/iNexio device support" if EXPERT
1071 depends on TOUCHSCREEN_USB_COMPOSITE
1073 config TOUCHSCREEN_USB_EASYTOUCH
1075 bool "EasyTouch USB Touch controller device support" if EXPERT
1076 depends on TOUCHSCREEN_USB_COMPOSITE
1078 Say Y here if you have an EasyTouch USB Touch controller.
1081 config TOUCHSCREEN_TOUCHIT213
1082 tristate "Sahara TouchIT-213 touchscreen"
1085 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
1089 To compile this driver as a module, choose M here: the
1090 module will be called touchit213.
1092 config TOUCHSCREEN_TS4800
1093 tristate "TS-4800 touchscreen"
1094 depends on HAS_IOMEM && OF
1095 depends on SOC_IMX51 || COMPILE_TEST
1098 Say Y here if you have a touchscreen on a TS-4800 board.
1100 On TS-4800, the touchscreen is not handled directly by Linux but by
1105 To compile this driver as a module, choose M here: the
1106 module will be called ts4800_ts.
1108 config TOUCHSCREEN_TSC_SERIO
1109 tristate "TSC-10/25/40 serial touchscreen support"
1112 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
1117 To compile this driver as a module, choose M here: the
1118 module will be called tsc40.
1120 config TOUCHSCREEN_TSC200X_CORE
1123 config TOUCHSCREEN_TSC2004
1124 tristate "TSC2004 based touchscreens"
1127 select TOUCHSCREEN_TSC200X_CORE
1129 Say Y here if you have a TSC2004 based touchscreen.
1133 To compile this driver as a module, choose M here: the
1134 module will be called tsc2004.
1136 config TOUCHSCREEN_TSC2005
1137 tristate "TSC2005 based touchscreens"
1138 depends on SPI_MASTER
1140 select TOUCHSCREEN_TSC200X_CORE
1142 Say Y here if you have a TSC2005 based touchscreen.
1146 To compile this driver as a module, choose M here: the
1147 module will be called tsc2005.
1149 config TOUCHSCREEN_TSC2007
1150 tristate "TSC2007 based touchscreens"
1153 Say Y here if you have a TSC2007 based touchscreen.
1157 To compile this driver as a module, choose M here: the
1158 module will be called tsc2007.
1160 config TOUCHSCREEN_TSC2007_IIO
1161 bool "IIO interface for external ADC input and temperature"
1162 depends on TOUCHSCREEN_TSC2007
1163 depends on IIO=y || IIO=TOUCHSCREEN_TSC2007
1165 Saying Y here adds an iio interface to the tsc2007 which
1166 provides values for the AUX input (used for e.g. battery
1167 or ambient light monitoring), temperature and raw input
1170 config TOUCHSCREEN_PCAP
1171 tristate "Motorola PCAP touchscreen"
1174 Say Y here if you have a Motorola EZX telephone and
1175 want to enable support for the built-in touchscreen.
1177 To compile this driver as a module, choose M here: the
1178 module will be called pcap_ts.
1180 config TOUCHSCREEN_RM_TS
1181 tristate "Raydium I2C Touchscreen"
1183 depends on GPIOLIB || COMPILE_TEST
1185 Say Y here if you have Raydium series I2C touchscreen,
1186 such as RM32380, connected to your system.
1190 To compile this driver as a module, choose M here: the
1191 module will be called raydium_i2c_ts.
1193 config TOUCHSCREEN_SILEAD
1194 tristate "Silead I2C touchscreen"
1197 Say Y here if you have the Silead touchscreen connected to
1202 To compile this driver as a module, choose M here: the
1203 module will be called silead.
1205 config TOUCHSCREEN_SIS_I2C
1206 tristate "SiS 9200 family I2C touchscreen"
1209 depends on GPIOLIB || COMPILE_TEST
1211 This enables support for SiS 9200 family over I2C based touchscreens.
1215 To compile this driver as a module, choose M here: the
1216 module will be called sis_i2c.
1218 config TOUCHSCREEN_ST1232
1219 tristate "Sitronix ST1232 or ST1633 touchscreen controllers"
1222 Say Y here if you want to support the Sitronix ST1232
1223 or ST1633 touchscreen controller.
1227 To compile this driver as a module, choose M here: the
1228 module will be called st1232_ts.
1230 config TOUCHSCREEN_STMFTS
1231 tristate "STMicroelectronics STMFTS touchscreen"
1233 depends on LEDS_CLASS
1235 Say Y here if you want support for STMicroelectronics
1238 To compile this driver as a module, choose M here: the
1239 module will be called stmfts.
1241 config TOUCHSCREEN_STMPE
1242 tristate "STMicroelectronics STMPE touchscreens"
1243 depends on MFD_STMPE
1244 depends on (OF || COMPILE_TEST)
1246 Say Y here if you want support for STMicroelectronics
1247 STMPE touchscreen controllers.
1249 To compile this driver as a module, choose M here: the
1250 module will be called stmpe-ts.
1252 config TOUCHSCREEN_SUN4I
1253 tristate "Allwinner sun4i resistive touchscreen controller support"
1254 depends on ARCH_SUNXI || COMPILE_TEST
1256 depends on THERMAL || !THERMAL_OF
1258 This selects support for the resistive touchscreen controller
1259 found on Allwinner sunxi SoCs.
1261 To compile this driver as a module, choose M here: the
1262 module will be called sun4i-ts.
1264 config TOUCHSCREEN_SUR40
1265 tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
1266 depends on USB && MEDIA_USB_SUPPORT && HAS_DMA
1267 depends on VIDEO_V4L2
1268 select VIDEOBUF2_DMA_SG
1270 Say Y here if you want support for the Samsung SUR40 touchscreen
1271 (also known as Microsoft Surface 2.0 or Microsoft PixelSense).
1273 To compile this driver as a module, choose M here: the
1274 module will be called sur40.
1276 config TOUCHSCREEN_SURFACE3_SPI
1277 tristate "Ntrig/Microsoft Surface 3 SPI touchscreen"
1279 depends on GPIOLIB || COMPILE_TEST
1281 Say Y here if you have the Ntrig/Microsoft SPI touchscreen
1282 controller chip as found on the Surface 3 in your system.
1286 To compile this driver as a module, choose M here: the
1287 module will be called surface3_spi.
1289 config TOUCHSCREEN_SX8654
1290 tristate "Semtech SX8654 touchscreen"
1293 Say Y here if you have a Semtech SX8654 touchscreen controller.
1297 To compile this driver as a module, choose M here: the
1298 module will be called sx8654.
1300 config TOUCHSCREEN_TPS6507X
1301 tristate "TPS6507x based touchscreens"
1304 Say Y here if you have a TPS6507x based touchscreen
1309 To compile this driver as a module, choose M here: the
1310 module will be called tps6507x_ts.
1312 config TOUCHSCREEN_ZET6223
1313 tristate "Zeitec ZET6223 touchscreen driver"
1316 Say Y here if you have a touchscreen using Zeitec ZET6223
1320 To compile this driver as a module, choose M here: the
1321 module will be called zet6223.
1323 config TOUCHSCREEN_ZFORCE
1324 tristate "Neonode zForce infrared touchscreens"
1326 depends on GPIOLIB || COMPILE_TEST
1328 Say Y here if you have a touchscreen using the zforce
1329 infraread technology from Neonode.
1333 To compile this driver as a module, choose M here: the
1334 module will be called zforce_ts.
1336 config TOUCHSCREEN_COLIBRI_VF50
1337 tristate "Toradex Colibri on board touchscreen driver"
1338 depends on IIO && VF610_ADC
1339 depends on GPIOLIB || COMPILE_TEST
1341 Say Y here if you have a Colibri VF50 and plan to use
1342 the on-board provided 4-wire touchscreen driver.
1346 To compile this driver as a module, choose M here: the
1347 module will be called colibri_vf50_ts.
1349 config TOUCHSCREEN_ROHM_BU21023
1350 tristate "ROHM BU21023/24 Dual touch support resistive touchscreens"
1353 Say Y here if you have a touchscreen using ROHM BU21023/24.
1357 To compile this driver as a module, choose M here: the
1358 module will be called bu21023_ts.
1360 config TOUCHSCREEN_IQS5XX
1361 tristate "Azoteq IQS550/572/525 trackpad/touchscreen controller"
1364 Say Y to enable support for the Azoteq IQS550/572/525
1365 family of trackpad/touchscreen controllers.
1367 To compile this driver as a module, choose M here: the
1368 module will be called iqs5xx.
1370 config TOUCHSCREEN_ZINITIX
1371 tristate "Zinitix touchscreen support"
1374 Say Y here if you have a touchscreen using Zinitix bt541,
1375 or something similar enough.
1379 To compile this driver as a module, choose M here: the
1380 module will be called zinitix.
1382 config TOUCHSCREEN_TINKER_FT5406
1383 tristate "tinker ft5406"
1386 Control ft5406 touch ic.