drivers/i2c/designware_i2c.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * (C) Copyright 2009
   4  * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
   5  */
   6
   7 #include <common.h>
   8 #include <clk.h>
   9 #include <dm.h>
  10 #include <i2c.h>
  11 #include <log.h>
  12 #include <malloc.h>
  13 #include <pci.h>
  14 #include <reset.h>
  15 #include <asm/io.h>
  16 #include <linux/delay.h>
  17 #include "designware_i2c.h"
  18 #include <dm/device_compat.h>
  19 #include <linux/err.h>
  20
  21 /*
  22  * This assigned unique hex value is constant and is derived from the two ASCII
  23  * letters 'DW' followed by a 16-bit unsigned number
  24  */
  25 #define DW_I2C_COMP_TYPE        0x44570140
  26
  27 #ifdef CONFIG_SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED
  28 static int  dw_i2c_enable(struct i2c_regs *i2c_base, bool enable)
  29 {
  30         u32 ena = enable ? IC_ENABLE_0B : 0;
  31
  32         writel(ena, &i2c_base->ic_enable);
  33
  34         return 0;
  35 }
  36 #else
  37 static int dw_i2c_enable(struct i2c_regs *i2c_base, bool enable)
  38 {
  39         u32 ena = enable ? IC_ENABLE_0B : 0;
  40         int timeout = 100;
  41
  42         do {
  43                 writel(ena, &i2c_base->ic_enable);
  44                 if ((readl(&i2c_base->ic_enable_status) & IC_ENABLE_0B) == ena)
  45                         return 0;
  46
  47                 /*
  48                  * Wait 10 times the signaling period of the highest I2C
  49                  * transfer supported by the driver (for 400KHz this is
  50                  * 25us) as described in the DesignWare I2C databook.
  51                  */
  52                 udelay(25);
  53         } while (timeout--);
  54         printf("timeout in %sabling I2C adapter\n", enable ? "en" : "dis");
  55
  56         return -ETIMEDOUT;
  57 }
  58 #endif
  59
  60 /* High and low times in different speed modes (in ns) */
  61 enum {
  62         /* SDA Hold Time */
  63         DEFAULT_SDA_HOLD_TIME           = 300,
  64 };
  65
  66 /**
  67  * calc_counts() - Convert a period to a number of IC clk cycles
  68  *
  69  * @ic_clk: Input clock in Hz
  70  * @period_ns: Period to represent, in ns
  71  * @return calculated count
  72  */
  73 static uint calc_counts(uint ic_clk, uint period_ns)
  74 {
  75         return DIV_ROUND_UP(ic_clk / 1000 * period_ns, NANO_TO_KILO);
  76 }
  77
  78 /**
  79  * struct i2c_mode_info - Information about an I2C speed mode
  80  *
  81  * Each speed mode has its own characteristics. This struct holds these to aid
  82  * calculations in dw_i2c_calc_timing().
  83  *
  84  * @speed: Speed in Hz
  85  * @min_scl_lowtime_ns: Minimum value for SCL low period in ns
  86  * @min_scl_hightime_ns: Minimum value for SCL high period in ns
  87  * @def_rise_time_ns: Default rise time in ns
  88  * @def_fall_time_ns: Default fall time in ns
  89  */
  90 struct i2c_mode_info {
  91         int speed;
  92         int min_scl_hightime_ns;
  93         int min_scl_lowtime_ns;
  94         int def_rise_time_ns;
  95         int def_fall_time_ns;
  96 };
  97
  98 static const struct i2c_mode_info info_for_mode[] = {
  99         [IC_SPEED_MODE_STANDARD] = {
 100                 I2C_SPEED_STANDARD_RATE,
 101                 MIN_SS_SCL_HIGHTIME,
 102                 MIN_SS_SCL_LOWTIME,
 103                 1000,
 104                 300,
 105         },
 106         [IC_SPEED_MODE_FAST] = {
 107                 I2C_SPEED_FAST_RATE,
 108                 MIN_FS_SCL_HIGHTIME,
 109                 MIN_FS_SCL_LOWTIME,
 110                 300,
 111                 300,
 112         },
 113         [IC_SPEED_MODE_FAST_PLUS] = {
 114                 I2C_SPEED_FAST_PLUS_RATE,
 115                 MIN_FP_SCL_HIGHTIME,
 116                 MIN_FP_SCL_LOWTIME,
 117                 260,
 118                 500,
 119         },
 120         [IC_SPEED_MODE_HIGH] = {
 121                 I2C_SPEED_HIGH_RATE,
 122                 MIN_HS_SCL_HIGHTIME,
 123                 MIN_HS_SCL_LOWTIME,
 124                 120,
 125                 120,
 126         },
 127 };
 128
 129 /**
 130  * dw_i2c_calc_timing() - Calculate the timings to use for a bus
 131  *
 132  * @priv: Bus private information (NULL if not using driver model)
 133  * @mode: Speed mode to use
 134  * @ic_clk: IC clock speed in Hz
 135  * @spk_cnt: Spike-suppression count
 136  * @config: Returns value to use
 137  * @return 0 if OK, -EINVAL if the calculation failed due to invalid data
 138  */
 139 static int dw_i2c_calc_timing(struct dw_i2c *priv, enum i2c_speed_mode mode,
 140                               int ic_clk, int spk_cnt,
 141                               struct dw_i2c_speed_config *config)
 142 {
 143         int fall_cnt, rise_cnt, min_tlow_cnt, min_thigh_cnt;
 144         int hcnt, lcnt, period_cnt, diff, tot;
 145         int sda_hold_time_ns, scl_rise_time_ns, scl_fall_time_ns;
 146         const struct i2c_mode_info *info;
 147
 148         /*
 149          * Find the period, rise, fall, min tlow, and min thigh in terms of
 150          * counts of the IC clock
 151          */
 152         info = &info_for_mode[mode];
 153         period_cnt = ic_clk / info->speed;
 154         scl_rise_time_ns = priv && priv->scl_rise_time_ns ?
 155                  priv->scl_rise_time_ns : info->def_rise_time_ns;
 156         scl_fall_time_ns = priv && priv->scl_fall_time_ns ?
 157                  priv->scl_fall_time_ns : info->def_fall_time_ns;
 158         rise_cnt = calc_counts(ic_clk, scl_rise_time_ns);
 159         fall_cnt = calc_counts(ic_clk, scl_fall_time_ns);
 160         min_tlow_cnt = calc_counts(ic_clk, info->min_scl_lowtime_ns);
 161         min_thigh_cnt = calc_counts(ic_clk, info->min_scl_hightime_ns);
 162
 163         debug("dw_i2c: mode %d, ic_clk %d, speed %d, period %d rise %d fall %d tlow %d thigh %d spk %d\n",
 164               mode, ic_clk, info->speed, period_cnt, rise_cnt, fall_cnt,
 165               min_tlow_cnt, min_thigh_cnt, spk_cnt);
 166
 167         /*
 168          * Back-solve for hcnt and lcnt according to the following equations:
 169          * SCL_High_time = [(HCNT + IC_*_SPKLEN + 7) * ic_clk] + SCL_Fall_time
 170          * SCL_Low_time = [(LCNT + 1) * ic_clk] - SCL_Fall_time + SCL_Rise_time
 171          */
 172         hcnt = min_thigh_cnt - fall_cnt - 7 - spk_cnt;
 173         lcnt = min_tlow_cnt - rise_cnt + fall_cnt - 1;
 174
 175         if (hcnt < 0 || lcnt < 0) {
 176                 debug("dw_i2c: bad counts. hcnt = %d lcnt = %d\n", hcnt, lcnt);
 177                 return log_msg_ret("counts", -EINVAL);
 178         }
 179
 180         /*
 181          * Now add things back up to ensure the period is hit. If it is off,
 182          * split the difference and bias to lcnt for remainder
 183          */
 184         tot = hcnt + lcnt + 7 + spk_cnt + rise_cnt + 1;
 185
 186         if (tot < period_cnt) {
 187                 diff = (period_cnt - tot) / 2;
 188                 hcnt += diff;
 189                 lcnt += diff;
 190                 tot = hcnt + lcnt + 7 + spk_cnt + rise_cnt + 1;
 191                 lcnt += period_cnt - tot;
 192         }
 193
 194         config->scl_lcnt = lcnt;
 195         config->scl_hcnt = hcnt;
 196
 197         /* Use internal default unless other value is specified */
 198         sda_hold_time_ns = priv && priv->sda_hold_time_ns ?
 199                  priv->sda_hold_time_ns : DEFAULT_SDA_HOLD_TIME;
 200         config->sda_hold = calc_counts(ic_clk, sda_hold_time_ns);
 201
 202         debug("dw_i2c: hcnt = %d lcnt = %d sda hold = %d\n", hcnt, lcnt,
 203               config->sda_hold);
 204
 205         return 0;
 206 }
 207
 208 /**
 209  * calc_bus_speed() - Calculate the config to use for a particular i2c speed
 210  *
 211  * @priv: Private information for the driver (NULL if not using driver model)
 212  * @i2c_base: Registers for the I2C controller
 213  * @speed: Required i2c speed in Hz
 214  * @bus_clk: Input clock to the I2C controller in Hz (e.g. IC_CLK)
 215  * @config: Returns the config to use for this speed
 216  * @return 0 if OK, -ve on error
 217  */
 218 static int calc_bus_speed(struct dw_i2c *priv, struct i2c_regs *regs, int speed,
 219                           ulong bus_clk, struct dw_i2c_speed_config *config)
 220 {
 221         const struct dw_scl_sda_cfg *scl_sda_cfg = NULL;
 222         enum i2c_speed_mode i2c_spd;
 223         int spk_cnt;
 224         int ret;
 225
 226         if (priv)
 227                 scl_sda_cfg = priv->scl_sda_cfg;
 228         /* Allow high speed if there is no config, or the config allows it */
 229         if (speed >= I2C_SPEED_HIGH_RATE)
 230                 i2c_spd = IC_SPEED_MODE_HIGH;
 231         else if (speed >= I2C_SPEED_FAST_PLUS_RATE)
 232                 i2c_spd = IC_SPEED_MODE_FAST_PLUS;
 233         else if (speed >= I2C_SPEED_FAST_RATE)
 234                 i2c_spd = IC_SPEED_MODE_FAST;
 235         else
 236                 i2c_spd = IC_SPEED_MODE_STANDARD;
 237
 238         /* Check is high speed possible and fall back to fast mode if not */
 239         if (i2c_spd == IC_SPEED_MODE_HIGH) {
 240                 u32 comp_param1;
 241
 242                 comp_param1 = readl(&regs->comp_param1);
 243                 if ((comp_param1 & DW_IC_COMP_PARAM_1_SPEED_MODE_MASK)
 244                                 != DW_IC_COMP_PARAM_1_SPEED_MODE_HIGH)
 245                         i2c_spd = IC_SPEED_MODE_FAST;
 246         }
 247
 248         /* Get the proper spike-suppression count based on target speed */
 249         if (!priv || !priv->has_spk_cnt)
 250                 spk_cnt = 0;
 251         else if (i2c_spd >= IC_SPEED_MODE_HIGH)
 252                 spk_cnt = readl(&regs->hs_spklen);
 253         else
 254                 spk_cnt = readl(&regs->fs_spklen);
 255         if (scl_sda_cfg) {
 256                 config->sda_hold = scl_sda_cfg->sda_hold;
 257                 if (i2c_spd == IC_SPEED_MODE_STANDARD) {
 258                         config->scl_hcnt = scl_sda_cfg->ss_hcnt;
 259                         config->scl_lcnt = scl_sda_cfg->ss_lcnt;
 260                 } else if (i2c_spd == IC_SPEED_MODE_HIGH) {
 261                         config->scl_hcnt = scl_sda_cfg->hs_hcnt;
 262                         config->scl_lcnt = scl_sda_cfg->hs_lcnt;
 263                 } else {
 264                         config->scl_hcnt = scl_sda_cfg->fs_hcnt;
 265                         config->scl_lcnt = scl_sda_cfg->fs_lcnt;
 266                 }
 267         } else {
 268                 ret = dw_i2c_calc_timing(priv, i2c_spd, bus_clk, spk_cnt,
 269                                          config);
 270                 if (ret)
 271                         return log_msg_ret("gen_confg", ret);
 272         }
 273         config->speed_mode = i2c_spd;
 274
 275         return 0;
 276 }
 277
 278 /**
 279  * _dw_i2c_set_bus_speed() - Set the i2c speed
 280  *
 281  * @priv: Private information for the driver (NULL if not using driver model)
 282  * @i2c_base: Registers for the I2C controller
 283  * @speed: Required i2c speed in Hz
 284  * @bus_clk: Input clock to the I2C controller in Hz (e.g. IC_CLK)
 285  * @return 0 if OK, -ve on error
 286  */
 287 static int _dw_i2c_set_bus_speed(struct dw_i2c *priv, struct i2c_regs *i2c_base,
 288                                  unsigned int speed, unsigned int bus_clk)
 289 {
 290         struct dw_i2c_speed_config config;
 291         unsigned int cntl;
 292         unsigned int ena;
 293         int ret;
 294
 295         ret = calc_bus_speed(priv, i2c_base, speed, bus_clk, &config);
 296         if (ret)
 297                 return ret;
 298
 299         /* Get enable setting for restore later */
 300         ena = readl(&i2c_base->ic_enable) & IC_ENABLE_0B;
 301
 302         /* to set speed cltr must be disabled */
 303         dw_i2c_enable(i2c_base, false);
 304
 305         cntl = (readl(&i2c_base->ic_con) & (~IC_CON_SPD_MSK));
 306
 307         switch (config.speed_mode) {
 308         case IC_SPEED_MODE_HIGH:
 309                 cntl |= IC_CON_SPD_HS;
 310                 writel(config.scl_hcnt, &i2c_base->ic_hs_scl_hcnt);
 311                 writel(config.scl_lcnt, &i2c_base->ic_hs_scl_lcnt);
 312                 break;
 313         case IC_SPEED_MODE_STANDARD:
 314                 cntl |= IC_CON_SPD_SS;
 315                 writel(config.scl_hcnt, &i2c_base->ic_ss_scl_hcnt);
 316                 writel(config.scl_lcnt, &i2c_base->ic_ss_scl_lcnt);
 317                 break;
 318         case IC_SPEED_MODE_FAST_PLUS:
 319         case IC_SPEED_MODE_FAST:
 320         default:
 321                 cntl |= IC_CON_SPD_FS;
 322                 writel(config.scl_hcnt, &i2c_base->ic_fs_scl_hcnt);
 323                 writel(config.scl_lcnt, &i2c_base->ic_fs_scl_lcnt);
 324                 break;
 325         }
 326
 327         writel(cntl, &i2c_base->ic_con);
 328
 329         /* Configure SDA Hold Time if required */
 330         if (config.sda_hold)
 331                 writel(config.sda_hold, &i2c_base->ic_sda_hold);
 332
 333         /* Restore back i2c now speed set */
 334         if (ena == IC_ENABLE_0B)
 335                 dw_i2c_enable(i2c_base, true);
 336         if (priv)
 337                 priv->config = config;
 338
 339         return 0;
 340 }
 341
 342 int dw_i2c_gen_speed_config(const struct udevice *dev, int speed_hz,
 343                             struct dw_i2c_speed_config *config)
 344 {
 345         struct dw_i2c *priv = dev_get_priv(dev);
 346         ulong rate;
 347         int ret;
 348
 349 #if CONFIG_IS_ENABLED(CLK)
 350         rate = clk_get_rate(&priv->clk);
 351         if (IS_ERR_VALUE(rate))
 352                 return log_msg_ret("clk", -EINVAL);
 353 #else
 354         rate = IC_CLK;
 355 #endif
 356
 357         ret = calc_bus_speed(priv, priv->regs, speed_hz, rate, config);
 358         if (ret)
 359                 printf("%s: ret=%d\n", __func__, ret);
 360         if (ret)
 361                 return log_msg_ret("calc_bus_speed", ret);
 362
 363         return 0;
 364 }
 365
 366 /*
 367  * i2c_setaddress - Sets the target slave address
 368  * @i2c_addr:   target i2c address
 369  *
 370  * Sets the target slave address.
 371  */
 372 static void i2c_setaddress(struct i2c_regs *i2c_base, unsigned int i2c_addr)
 373 {
 374         /* Disable i2c */
 375         dw_i2c_enable(i2c_base, false);
 376
 377         writel(i2c_addr, &i2c_base->ic_tar);
 378
 379         /* Enable i2c */
 380         dw_i2c_enable(i2c_base, true);
 381 }
 382
 383 /*
 384  * i2c_flush_rxfifo - Flushes the i2c RX FIFO
 385  *
 386  * Flushes the i2c RX FIFO
 387  */
 388 static void i2c_flush_rxfifo(struct i2c_regs *i2c_base)
 389 {
 390         while (readl(&i2c_base->ic_status) & IC_STATUS_RFNE)
 391                 readl(&i2c_base->ic_cmd_data);
 392 }
 393
 394 /*
 395  * i2c_wait_for_bb - Waits for bus busy
 396  *
 397  * Waits for bus busy
 398  */
 399 static int i2c_wait_for_bb(struct i2c_regs *i2c_base)
 400 {
 401         unsigned long start_time_bb = get_timer(0);
 402
 403         while ((readl(&i2c_base->ic_status) & IC_STATUS_MA) ||
 404                !(readl(&i2c_base->ic_status) & IC_STATUS_TFE)) {
 405
 406                 /* Evaluate timeout */
 407                 if (get_timer(start_time_bb) > (unsigned long)(I2C_BYTE_TO_BB))
 408                         return 1;
 409         }
 410
 411         return 0;
 412 }
 413
 414 static int i2c_xfer_init(struct i2c_regs *i2c_base, uchar chip, uint addr,
 415                          int alen)
 416 {
 417         if (i2c_wait_for_bb(i2c_base))
 418                 return 1;
 419
 420         i2c_setaddress(i2c_base, chip);
 421         while (alen) {
 422                 alen--;
 423                 /* high byte address going out first */
 424                 writel((addr >> (alen * 8)) & 0xff,
 425                        &i2c_base->ic_cmd_data);
 426         }
 427         return 0;
 428 }
 429
 430 static int i2c_xfer_finish(struct i2c_regs *i2c_base)
 431 {
 432         ulong start_stop_det = get_timer(0);
 433
 434         while (1) {
 435                 if ((readl(&i2c_base->ic_raw_intr_stat) & IC_STOP_DET)) {
 436                         readl(&i2c_base->ic_clr_stop_det);
 437                         break;
 438                 } else if (get_timer(start_stop_det) > I2C_STOPDET_TO) {
 439                         break;
 440                 }
 441         }
 442
 443         if (i2c_wait_for_bb(i2c_base)) {
 444                 printf("Timed out waiting for bus\n");
 445                 return 1;
 446         }
 447
 448         i2c_flush_rxfifo(i2c_base);
 449
 450         return 0;
 451 }
 452
 453 /*
 454  * i2c_read - Read from i2c memory
 455  * @chip:       target i2c address
 456  * @addr:       address to read from
 457  * @alen:
 458  * @buffer:     buffer for read data
 459  * @len:        no of bytes to be read
 460  *
 461  * Read from i2c memory.
 462  */
 463 static int __dw_i2c_read(struct i2c_regs *i2c_base, u8 dev, uint addr,
 464                          int alen, u8 *buffer, int len)
 465 {
 466         unsigned long start_time_rx;
 467         unsigned int active = 0;
 468
 469 #ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
 470         /*
 471          * EEPROM chips that implement "address overflow" are ones
 472          * like Catalyst 24WC04/08/16 which has 9/10/11 bits of
 473          * address and the extra bits end up in the "chip address"
 474          * bit slots. This makes a 24WC08 (1Kbyte) chip look like
 475          * four 256 byte chips.
 476          *
 477          * Note that we consider the length of the address field to
 478          * still be one byte because the extra address bits are
 479          * hidden in the chip address.
 480          */
 481         dev |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
 482         addr &= ~(CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW << (alen * 8));
 483
 484         debug("%s: fix addr_overflow: dev %02x addr %02x\n", __func__, dev,
 485               addr);
 486 #endif
 487
 488         if (i2c_xfer_init(i2c_base, dev, addr, alen))
 489                 return 1;
 490
 491         start_time_rx = get_timer(0);
 492         while (len) {
 493                 if (!active) {
 494                         /*
 495                          * Avoid writing to ic_cmd_data multiple times
 496                          * in case this loop spins too quickly and the
 497                          * ic_status RFNE bit isn't set after the first
 498                          * write. Subsequent writes to ic_cmd_data can
 499                          * trigger spurious i2c transfer.
 500                          */
 501                         if (len == 1)
 502                                 writel(IC_CMD | IC_STOP, &i2c_base->ic_cmd_data);
 503                         else
 504                                 writel(IC_CMD, &i2c_base->ic_cmd_data);
 505                         active = 1;
 506                 }
 507
 508                 if (readl(&i2c_base->ic_status) & IC_STATUS_RFNE) {
 509                         *buffer++ = (uchar)readl(&i2c_base->ic_cmd_data);
 510                         len--;
 511                         start_time_rx = get_timer(0);
 512                         active = 0;
 513                 } else if (get_timer(start_time_rx) > I2C_BYTE_TO) {
 514                         return 1;
 515                 }
 516         }
 517
 518         return i2c_xfer_finish(i2c_base);
 519 }
 520
 521 /*
 522  * i2c_write - Write to i2c memory
 523  * @chip:       target i2c address
 524  * @addr:       address to read from
 525  * @alen:
 526  * @buffer:     buffer for read data
 527  * @len:        no of bytes to be read
 528  *
 529  * Write to i2c memory.
 530  */
 531 static int __dw_i2c_write(struct i2c_regs *i2c_base, u8 dev, uint addr,
 532                           int alen, u8 *buffer, int len)
 533 {
 534         int nb = len;
 535         unsigned long start_time_tx;
 536
 537 #ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
 538         /*
 539          * EEPROM chips that implement "address overflow" are ones
 540          * like Catalyst 24WC04/08/16 which has 9/10/11 bits of
 541          * address and the extra bits end up in the "chip address"
 542          * bit slots. This makes a 24WC08 (1Kbyte) chip look like
 543          * four 256 byte chips.
 544          *
 545          * Note that we consider the length of the address field to
 546          * still be one byte because the extra address bits are
 547          * hidden in the chip address.
 548          */
 549         dev |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
 550         addr &= ~(CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW << (alen * 8));
 551
 552         debug("%s: fix addr_overflow: dev %02x addr %02x\n", __func__, dev,
 553               addr);
 554 #endif
 555
 556         if (i2c_xfer_init(i2c_base, dev, addr, alen))
 557                 return 1;
 558
 559         start_time_tx = get_timer(0);
 560         while (len) {
 561                 if (readl(&i2c_base->ic_status) & IC_STATUS_TFNF) {
 562                         if (--len == 0) {
 563                                 writel(*buffer | IC_STOP,
 564                                        &i2c_base->ic_cmd_data);
 565                         } else {
 566                                 writel(*buffer, &i2c_base->ic_cmd_data);
 567                         }
 568                         buffer++;
 569                         start_time_tx = get_timer(0);
 570
 571                 } else if (get_timer(start_time_tx) > (nb * I2C_BYTE_TO)) {
 572                                 printf("Timed out. i2c write Failed\n");
 573                                 return 1;
 574                 }
 575         }
 576
 577         return i2c_xfer_finish(i2c_base);
 578 }
 579
 580 /*
 581  * __dw_i2c_init - Init function
 582  * @speed:      required i2c speed
 583  * @slaveaddr:  slave address for the device
 584  *
 585  * Initialization function.
 586  */
 587 static int __dw_i2c_init(struct i2c_regs *i2c_base, int speed, int slaveaddr)
 588 {
 589         int ret;
 590
 591         /* Disable i2c */
 592         ret = dw_i2c_enable(i2c_base, false);
 593         if (ret)
 594                 return ret;
 595
 596         writel(IC_CON_SD | IC_CON_RE | IC_CON_SPD_FS | IC_CON_MM,
 597                &i2c_base->ic_con);
 598         writel(IC_RX_TL, &i2c_base->ic_rx_tl);
 599         writel(IC_TX_TL, &i2c_base->ic_tx_tl);
 600         writel(IC_STOP_DET, &i2c_base->ic_intr_mask);
 601 #ifndef CONFIG_DM_I2C
 602         _dw_i2c_set_bus_speed(NULL, i2c_base, speed, IC_CLK);
 603         writel(slaveaddr, &i2c_base->ic_sar);
 604 #endif
 605
 606         /* Enable i2c */
 607         ret = dw_i2c_enable(i2c_base, true);
 608         if (ret)
 609                 return ret;
 610
 611         return 0;
 612 }
 613
 614 #ifndef CONFIG_DM_I2C
 615 /*
 616  * The legacy I2C functions. These need to get removed once
 617  * all users of this driver are converted to DM.
 618  */
 619 static struct i2c_regs *i2c_get_base(struct i2c_adapter *adap)
 620 {
 621         switch (adap->hwadapnr) {
 622 #if CONFIG_SYS_I2C_BUS_MAX >= 4
 623         case 3:
 624                 return (struct i2c_regs *)CONFIG_SYS_I2C_BASE3;
 625 #endif
 626 #if CONFIG_SYS_I2C_BUS_MAX >= 3
 627         case 2:
 628                 return (struct i2c_regs *)CONFIG_SYS_I2C_BASE2;
 629 #endif
 630 #if CONFIG_SYS_I2C_BUS_MAX >= 2
 631         case 1:
 632                 return (struct i2c_regs *)CONFIG_SYS_I2C_BASE1;
 633 #endif
 634         case 0:
 635                 return (struct i2c_regs *)CONFIG_SYS_I2C_BASE;
 636         default:
 637                 printf("Wrong I2C-adapter number %d\n", adap->hwadapnr);
 638         }
 639
 640         return NULL;
 641 }
 642
 643 static unsigned int dw_i2c_set_bus_speed(struct i2c_adapter *adap,
 644                                          unsigned int speed)
 645 {
 646         adap->speed = speed;
 647         return _dw_i2c_set_bus_speed(NULL, i2c_get_base(adap), speed, IC_CLK);
 648 }
 649
 650 static void dw_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
 651 {
 652         __dw_i2c_init(i2c_get_base(adap), speed, slaveaddr);
 653 }
 654
 655 static int dw_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr,
 656                        int alen, u8 *buffer, int len)
 657 {
 658         return __dw_i2c_read(i2c_get_base(adap), dev, addr, alen, buffer, len);
 659 }
 660
 661 static int dw_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr,
 662                         int alen, u8 *buffer, int len)
 663 {
 664         return __dw_i2c_write(i2c_get_base(adap), dev, addr, alen, buffer, len);
 665 }
 666
 667 /* dw_i2c_probe - Probe the i2c chip */
 668 static int dw_i2c_probe(struct i2c_adapter *adap, u8 dev)
 669 {
 670         struct i2c_regs *i2c_base = i2c_get_base(adap);
 671         u32 tmp;
 672         int ret;
 673
 674         /*
 675          * Try to read the first location of the chip.
 676          */
 677         ret = __dw_i2c_read(i2c_base, dev, 0, 1, (uchar *)&tmp, 1);
 678         if (ret)
 679                 dw_i2c_init(adap, adap->speed, adap->slaveaddr);
 680
 681         return ret;
 682 }
 683
 684 U_BOOT_I2C_ADAP_COMPLETE(dw_0, dw_i2c_init, dw_i2c_probe, dw_i2c_read,
 685                          dw_i2c_write, dw_i2c_set_bus_speed,
 686                          CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE, 0)
 687
 688 #if CONFIG_SYS_I2C_BUS_MAX >= 2
 689 U_BOOT_I2C_ADAP_COMPLETE(dw_1, dw_i2c_init, dw_i2c_probe, dw_i2c_read,
 690                          dw_i2c_write, dw_i2c_set_bus_speed,
 691                          CONFIG_SYS_I2C_SPEED1, CONFIG_SYS_I2C_SLAVE1, 1)
 692 #endif
 693
 694 #if CONFIG_SYS_I2C_BUS_MAX >= 3
 695 U_BOOT_I2C_ADAP_COMPLETE(dw_2, dw_i2c_init, dw_i2c_probe, dw_i2c_read,
 696                          dw_i2c_write, dw_i2c_set_bus_speed,
 697                          CONFIG_SYS_I2C_SPEED2, CONFIG_SYS_I2C_SLAVE2, 2)
 698 #endif
 699
 700 #if CONFIG_SYS_I2C_BUS_MAX >= 4
 701 U_BOOT_I2C_ADAP_COMPLETE(dw_3, dw_i2c_init, dw_i2c_probe, dw_i2c_read,
 702                          dw_i2c_write, dw_i2c_set_bus_speed,
 703                          CONFIG_SYS_I2C_SPEED3, CONFIG_SYS_I2C_SLAVE3, 3)
 704 #endif
 705
 706 #else /* CONFIG_DM_I2C */
 707 /* The DM I2C functions */
 708
 709 static int designware_i2c_xfer(struct udevice *bus, struct i2c_msg *msg,
 710                                int nmsgs)
 711 {
 712         struct dw_i2c *i2c = dev_get_priv(bus);
 713         int ret;
 714
 715         debug("i2c_xfer: %d messages\n", nmsgs);
 716         for (; nmsgs > 0; nmsgs--, msg++) {
 717                 debug("i2c_xfer: chip=0x%x, len=0x%x\n", msg->addr, msg->len);
 718                 if (msg->flags & I2C_M_RD) {
 719                         ret = __dw_i2c_read(i2c->regs, msg->addr, 0, 0,
 720                                             msg->buf, msg->len);
 721                 } else {
 722                         ret = __dw_i2c_write(i2c->regs, msg->addr, 0, 0,
 723                                              msg->buf, msg->len);
 724                 }
 725                 if (ret) {
 726                         debug("i2c_write: error sending\n");
 727                         return -EREMOTEIO;
 728                 }
 729         }
 730
 731         return 0;
 732 }
 733
 734 static int designware_i2c_set_bus_speed(struct udevice *bus, unsigned int speed)
 735 {
 736         struct dw_i2c *i2c = dev_get_priv(bus);
 737         ulong rate;
 738
 739 #if CONFIG_IS_ENABLED(CLK)
 740         rate = clk_get_rate(&i2c->clk);
 741         if (IS_ERR_VALUE(rate))
 742                 return log_ret(-EINVAL);
 743 #else
 744         rate = IC_CLK;
 745 #endif
 746         return _dw_i2c_set_bus_speed(i2c, i2c->regs, speed, rate);
 747 }
 748
 749 static int designware_i2c_probe_chip(struct udevice *bus, uint chip_addr,
 750                                      uint chip_flags)
 751 {
 752         struct dw_i2c *i2c = dev_get_priv(bus);
 753         struct i2c_regs *i2c_base = i2c->regs;
 754         u32 tmp;
 755         int ret;
 756
 757         /* Try to read the first location of the chip */
 758         ret = __dw_i2c_read(i2c_base, chip_addr, 0, 1, (uchar *)&tmp, 1);
 759         if (ret)
 760                 __dw_i2c_init(i2c_base, 0, 0);
 761
 762         return ret;
 763 }
 764
 765 int designware_i2c_ofdata_to_platdata(struct udevice *bus)
 766 {
 767         struct dw_i2c *priv = dev_get_priv(bus);
 768         int ret;
 769
 770         if (!priv->regs)
 771                 priv->regs = dev_read_addr_ptr(bus);
 772         dev_read_u32(bus, "i2c-scl-rising-time-ns", &priv->scl_rise_time_ns);
 773         dev_read_u32(bus, "i2c-scl-falling-time-ns", &priv->scl_fall_time_ns);
 774         dev_read_u32(bus, "i2c-sda-hold-time-ns", &priv->sda_hold_time_ns);
 775
 776         ret = reset_get_bulk(bus, &priv->resets);
 777         if (ret)
 778                 dev_warn(bus, "Can't get reset: %d\n", ret);
 779         else
 780                 reset_deassert_bulk(&priv->resets);
 781
 782 #if CONFIG_IS_ENABLED(CLK)
 783         ret = clk_get_by_index(bus, 0, &priv->clk);
 784         if (ret)
 785                 return ret;
 786
 787         ret = clk_enable(&priv->clk);
 788         if (ret && ret != -ENOSYS && ret != -ENOTSUPP) {
 789                 clk_free(&priv->clk);
 790                 dev_err(bus, "failed to enable clock\n");
 791                 return ret;
 792         }
 793 #endif
 794
 795         return 0;
 796 }
 797
 798 int designware_i2c_probe(struct udevice *bus)
 799 {
 800         struct dw_i2c *priv = dev_get_priv(bus);
 801         uint comp_type;
 802
 803         comp_type = readl(&priv->regs->comp_type);
 804         if (comp_type != DW_I2C_COMP_TYPE) {
 805                 log_err("I2C bus %s has unknown type %#x\n", bus->name,
 806                         comp_type);
 807                 return -ENXIO;
 808         }
 809
 810         log_debug("I2C bus %s version %#x\n", bus->name,
 811                   readl(&priv->regs->comp_version));
 812
 813         return __dw_i2c_init(priv->regs, 0, 0);
 814 }
 815
 816 int designware_i2c_remove(struct udevice *dev)
 817 {
 818         struct dw_i2c *priv = dev_get_priv(dev);
 819
 820 #if CONFIG_IS_ENABLED(CLK)
 821         clk_disable(&priv->clk);
 822         clk_free(&priv->clk);
 823 #endif
 824
 825         return reset_release_bulk(&priv->resets);
 826 }
 827
 828 const struct dm_i2c_ops designware_i2c_ops = {
 829         .xfer           = designware_i2c_xfer,
 830         .probe_chip     = designware_i2c_probe_chip,
 831         .set_bus_speed  = designware_i2c_set_bus_speed,
 832 };
 833
 834 static const struct udevice_id designware_i2c_ids[] = {
 835         { .compatible = "snps,designware-i2c" },
 836         { }
 837 };
 838
 839 U_BOOT_DRIVER(i2c_designware) = {
 840         .name   = "i2c_designware",
 841         .id     = UCLASS_I2C,
 842         .of_match = designware_i2c_ids,
 843         .ofdata_to_platdata = designware_i2c_ofdata_to_platdata,
 844         .probe  = designware_i2c_probe,
 845         .priv_auto_alloc_size = sizeof(struct dw_i2c),
 846         .remove = designware_i2c_remove,
 847         .flags  = DM_FLAG_OS_PREPARE,
 848         .ops    = &designware_i2c_ops,
 849 };
 850
 851 #endif /* CONFIG_DM_I2C */