1 // SPDX-License-Identifier: GPL-2.0
3 * Driver for the Renesas R-Car I2C unit
5 * Copyright (C) 2014-19 Wolfram Sang <wsa@sang-engineering.com>
6 * Copyright (C) 2011-2019 Renesas Electronics Corporation
8 * Copyright (C) 2012-14 Renesas Solutions Corp.
9 * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
11 * This file is based on the drivers/i2c/busses/i2c-sh7760.c
12 * (c) 2005-2008 MSC Vertriebsges.m.b.H, Manuel Lauss <mlau@msc-ge.com>
14 #include <linux/bitops.h>
15 #include <linux/clk.h>
16 #include <linux/delay.h>
17 #include <linux/dmaengine.h>
18 #include <linux/dma-mapping.h>
19 #include <linux/err.h>
20 #include <linux/interrupt.h>
22 #include <linux/i2c.h>
23 #include <linux/kernel.h>
24 #include <linux/module.h>
25 #include <linux/of_device.h>
26 #include <linux/platform_device.h>
27 #include <linux/pm_runtime.h>
28 #include <linux/reset.h>
29 #include <linux/slab.h>
31 /* register offsets */
32 #define ICSCR 0x00 /* slave ctrl */
33 #define ICMCR 0x04 /* master ctrl */
34 #define ICSSR 0x08 /* slave status */
35 #define ICMSR 0x0C /* master status */
36 #define ICSIER 0x10 /* slave irq enable */
37 #define ICMIER 0x14 /* master irq enable */
38 #define ICCCR 0x18 /* clock dividers */
39 #define ICSAR 0x1C /* slave address */
40 #define ICMAR 0x20 /* master address */
41 #define ICRXTX 0x24 /* data port */
42 #define ICFBSCR 0x38 /* first bit setup cycle (Gen3) */
43 #define ICDMAER 0x3c /* DMA enable (Gen3) */
46 #define SDBS (1 << 3) /* slave data buffer select */
47 #define SIE (1 << 2) /* slave interface enable */
48 #define GCAE (1 << 1) /* general call address enable */
49 #define FNA (1 << 0) /* forced non acknowledgment */
52 #define MDBS (1 << 7) /* non-fifo mode switch */
53 #define FSCL (1 << 6) /* override SCL pin */
54 #define FSDA (1 << 5) /* override SDA pin */
55 #define OBPC (1 << 4) /* override pins */
56 #define MIE (1 << 3) /* master if enable */
58 #define FSB (1 << 1) /* force stop bit */
59 #define ESG (1 << 0) /* enable start bit gen */
61 /* ICSSR (also for ICSIER) */
62 #define GCAR (1 << 6) /* general call received */
63 #define STM (1 << 5) /* slave transmit mode */
64 #define SSR (1 << 4) /* stop received */
65 #define SDE (1 << 3) /* slave data empty */
66 #define SDT (1 << 2) /* slave data transmitted */
67 #define SDR (1 << 1) /* slave data received */
68 #define SAR (1 << 0) /* slave addr received */
70 /* ICMSR (also for ICMIE) */
71 #define MNR (1 << 6) /* nack received */
72 #define MAL (1 << 5) /* arbitration lost */
73 #define MST (1 << 4) /* sent a stop */
77 #define MAT (1 << 0) /* slave addr xfer done */
80 #define RSDMAE (1 << 3) /* DMA Slave Received Enable */
81 #define TSDMAE (1 << 2) /* DMA Slave Transmitted Enable */
82 #define RMDMAE (1 << 1) /* DMA Master Received Enable */
83 #define TMDMAE (1 << 0) /* DMA Master Transmitted Enable */
86 #define TCYC17 0x0f /* 17*Tcyc delay 1st bit between SDA and SCL */
88 #define RCAR_MIN_DMA_LEN 8
90 #define RCAR_BUS_PHASE_START (MDBS | MIE | ESG)
91 #define RCAR_BUS_PHASE_DATA (MDBS | MIE)
92 #define RCAR_BUS_MASK_DATA (~(ESG | FSB) & 0xFF)
93 #define RCAR_BUS_PHASE_STOP (MDBS | MIE | FSB)
95 #define RCAR_IRQ_SEND (MNR | MAL | MST | MAT | MDE)
96 #define RCAR_IRQ_RECV (MNR | MAL | MST | MAT | MDR)
97 #define RCAR_IRQ_STOP (MST)
99 #define RCAR_IRQ_ACK_SEND (~(MAT | MDE) & 0x7F)
100 #define RCAR_IRQ_ACK_RECV (~(MAT | MDR) & 0x7F)
102 #define ID_LAST_MSG (1 << 0)
103 #define ID_FIRST_MSG (1 << 1)
104 #define ID_DONE (1 << 2)
105 #define ID_ARBLOST (1 << 3)
106 #define ID_NACK (1 << 4)
107 /* persistent flags */
108 #define ID_P_REP_AFTER_RD BIT(29)
109 #define ID_P_NO_RXDMA BIT(30) /* HW forbids RXDMA sometimes */
110 #define ID_P_PM_BLOCKED BIT(31)
111 #define ID_P_MASK GENMASK(31, 29)
119 struct rcar_i2c_priv {
121 struct i2c_adapter adap;
126 wait_queue_head_t wait;
131 u8 recovery_icmcr; /* protected by adapter lock */
132 enum rcar_i2c_type devtype;
133 struct i2c_client *slave;
135 struct resource *res;
136 struct dma_chan *dma_tx;
137 struct dma_chan *dma_rx;
138 struct scatterlist sg;
139 enum dma_data_direction dma_direction;
141 struct reset_control *rstc;
145 #define rcar_i2c_priv_to_dev(p) ((p)->adap.dev.parent)
146 #define rcar_i2c_is_recv(p) ((p)->msg->flags & I2C_M_RD)
148 #define LOOP_TIMEOUT 1024
151 static void rcar_i2c_write(struct rcar_i2c_priv *priv, int reg, u32 val)
153 writel(val, priv->io + reg);
156 static u32 rcar_i2c_read(struct rcar_i2c_priv *priv, int reg)
158 return readl(priv->io + reg);
161 static int rcar_i2c_get_scl(struct i2c_adapter *adap)
163 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
165 return !!(rcar_i2c_read(priv, ICMCR) & FSCL);
169 static void rcar_i2c_set_scl(struct i2c_adapter *adap, int val)
171 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
174 priv->recovery_icmcr |= FSCL;
176 priv->recovery_icmcr &= ~FSCL;
178 rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr);
181 static void rcar_i2c_set_sda(struct i2c_adapter *adap, int val)
183 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
186 priv->recovery_icmcr |= FSDA;
188 priv->recovery_icmcr &= ~FSDA;
190 rcar_i2c_write(priv, ICMCR, priv->recovery_icmcr);
193 static int rcar_i2c_get_bus_free(struct i2c_adapter *adap)
195 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
197 return !(rcar_i2c_read(priv, ICMCR) & FSDA);
201 static struct i2c_bus_recovery_info rcar_i2c_bri = {
202 .get_scl = rcar_i2c_get_scl,
203 .set_scl = rcar_i2c_set_scl,
204 .set_sda = rcar_i2c_set_sda,
205 .get_bus_free = rcar_i2c_get_bus_free,
206 .recover_bus = i2c_generic_scl_recovery,
208 static void rcar_i2c_init(struct rcar_i2c_priv *priv)
210 /* reset master mode */
211 rcar_i2c_write(priv, ICMIER, 0);
212 rcar_i2c_write(priv, ICMCR, MDBS);
213 rcar_i2c_write(priv, ICMSR, 0);
215 rcar_i2c_write(priv, ICCCR, priv->icccr);
217 if (priv->devtype == I2C_RCAR_GEN3)
218 rcar_i2c_write(priv, ICFBSCR, TCYC17);
222 static int rcar_i2c_bus_barrier(struct rcar_i2c_priv *priv)
226 for (i = 0; i < LOOP_TIMEOUT; i++) {
227 /* make sure that bus is not busy */
228 if (!(rcar_i2c_read(priv, ICMCR) & FSDA))
233 /* Waiting did not help, try to recover */
234 priv->recovery_icmcr = MDBS | OBPC | FSDA | FSCL;
235 return i2c_recover_bus(&priv->adap);
238 static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv, struct i2c_timings *t)
240 u32 scgd, cdf, round, ick, sum, scl, cdf_width;
242 struct device *dev = rcar_i2c_priv_to_dev(priv);
244 /* Fall back to previously used values if not supplied */
245 t->bus_freq_hz = t->bus_freq_hz ?: 100000;
246 t->scl_fall_ns = t->scl_fall_ns ?: 35;
247 t->scl_rise_ns = t->scl_rise_ns ?: 200;
248 t->scl_int_delay_ns = t->scl_int_delay_ns ?: 50;
250 switch (priv->devtype) {
259 dev_err(dev, "device type error\n");
264 * calculate SCL clock
268 * ick = clkp / (1 + CDF)
269 * SCL = ick / (20 + SCGD * 8 + F[(ticf + tr + intd) * ick])
271 * ick : I2C internal clock < 20 MHz
272 * ticf : I2C SCL falling time
273 * tr : I2C SCL rising time
274 * intd : LSI internal delay
275 * clkp : peripheral_clk
276 * F[] : integer up-valuation
278 rate = clk_get_rate(priv->clk);
279 cdf = rate / 20000000;
280 if (cdf >= 1U << cdf_width) {
281 dev_err(dev, "Input clock %lu too high\n", rate);
284 ick = rate / (cdf + 1);
287 * it is impossible to calculate large scale
288 * number on u32. separate it
290 * F[(ticf + tr + intd) * ick] with sum = (ticf + tr + intd)
291 * = F[sum * ick / 1000000000]
292 * = F[(ick / 1000000) * sum / 1000]
294 sum = t->scl_fall_ns + t->scl_rise_ns + t->scl_int_delay_ns;
295 round = (ick + 500000) / 1000000 * sum;
296 round = (round + 500) / 1000;
299 * SCL = ick / (20 + SCGD * 8 + F[(ticf + tr + intd) * ick])
301 * Calculation result (= SCL) should be less than
302 * bus_speed for hardware safety
304 * We could use something along the lines of
305 * div = ick / (bus_speed + 1) + 1;
306 * scgd = (div - 20 - round + 7) / 8;
307 * scl = ick / (20 + (scgd * 8) + round);
308 * (not fully verified) but that would get pretty involved
310 for (scgd = 0; scgd < 0x40; scgd++) {
311 scl = ick / (20 + (scgd * 8) + round);
312 if (scl <= t->bus_freq_hz)
315 dev_err(dev, "it is impossible to calculate best SCL\n");
319 dev_dbg(dev, "clk %d/%d(%lu), round %u, CDF:0x%x, SCGD: 0x%x\n",
320 scl, t->bus_freq_hz, clk_get_rate(priv->clk), round, cdf, scgd);
322 /* keep icccr value */
323 priv->icccr = scgd << cdf_width | cdf;
328 static void rcar_i2c_prepare_msg(struct rcar_i2c_priv *priv)
330 int read = !!rcar_i2c_is_recv(priv);
333 if (priv->msgs_left == 1)
334 priv->flags |= ID_LAST_MSG;
336 rcar_i2c_write(priv, ICMAR, i2c_8bit_addr_from_msg(priv->msg));
338 * We don't have a test case but the HW engineers say that the write order
339 * of ICMSR and ICMCR depends on whether we issue START or REP_START. Since
340 * it didn't cause a drawback for me, let's rather be safe than sorry.
342 if (priv->flags & ID_FIRST_MSG) {
343 rcar_i2c_write(priv, ICMSR, 0);
344 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
346 if (priv->flags & ID_P_REP_AFTER_RD)
347 priv->flags &= ~ID_P_REP_AFTER_RD;
349 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
350 rcar_i2c_write(priv, ICMSR, 0);
352 rcar_i2c_write(priv, ICMIER, read ? RCAR_IRQ_RECV : RCAR_IRQ_SEND);
355 static void rcar_i2c_next_msg(struct rcar_i2c_priv *priv)
359 priv->flags &= ID_P_MASK;
360 rcar_i2c_prepare_msg(priv);
363 static void rcar_i2c_dma_unmap(struct rcar_i2c_priv *priv)
365 struct dma_chan *chan = priv->dma_direction == DMA_FROM_DEVICE
366 ? priv->dma_rx : priv->dma_tx;
368 dma_unmap_single(chan->device->dev, sg_dma_address(&priv->sg),
369 sg_dma_len(&priv->sg), priv->dma_direction);
371 /* Gen3 can only do one RXDMA per transfer and we just completed it */
372 if (priv->devtype == I2C_RCAR_GEN3 &&
373 priv->dma_direction == DMA_FROM_DEVICE)
374 priv->flags |= ID_P_NO_RXDMA;
376 priv->dma_direction = DMA_NONE;
378 /* Disable DMA Master Received/Transmitted, must be last! */
379 rcar_i2c_write(priv, ICDMAER, 0);
382 static void rcar_i2c_cleanup_dma(struct rcar_i2c_priv *priv)
384 if (priv->dma_direction == DMA_NONE)
386 else if (priv->dma_direction == DMA_FROM_DEVICE)
387 dmaengine_terminate_all(priv->dma_rx);
388 else if (priv->dma_direction == DMA_TO_DEVICE)
389 dmaengine_terminate_all(priv->dma_tx);
391 rcar_i2c_dma_unmap(priv);
394 static void rcar_i2c_dma_callback(void *data)
396 struct rcar_i2c_priv *priv = data;
398 priv->pos += sg_dma_len(&priv->sg);
400 rcar_i2c_dma_unmap(priv);
403 static bool rcar_i2c_dma(struct rcar_i2c_priv *priv)
405 struct device *dev = rcar_i2c_priv_to_dev(priv);
406 struct i2c_msg *msg = priv->msg;
407 bool read = msg->flags & I2C_M_RD;
408 enum dma_data_direction dir = read ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
409 struct dma_chan *chan = read ? priv->dma_rx : priv->dma_tx;
410 struct dma_async_tx_descriptor *txdesc;
416 /* Do various checks to see if DMA is feasible at all */
417 if (IS_ERR(chan) || msg->len < RCAR_MIN_DMA_LEN ||
418 !(msg->flags & I2C_M_DMA_SAFE) || (read && priv->flags & ID_P_NO_RXDMA))
423 * The last two bytes needs to be fetched using PIO in
424 * order for the STOP phase to work.
426 buf = priv->msg->buf;
427 len = priv->msg->len - 2;
430 * First byte in message was sent using PIO.
432 buf = priv->msg->buf + 1;
433 len = priv->msg->len - 1;
436 dma_addr = dma_map_single(chan->device->dev, buf, len, dir);
437 if (dma_mapping_error(chan->device->dev, dma_addr)) {
438 dev_dbg(dev, "dma map failed, using PIO\n");
442 sg_dma_len(&priv->sg) = len;
443 sg_dma_address(&priv->sg) = dma_addr;
445 priv->dma_direction = dir;
447 txdesc = dmaengine_prep_slave_sg(chan, &priv->sg, 1,
448 read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV,
449 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
451 dev_dbg(dev, "dma prep slave sg failed, using PIO\n");
452 rcar_i2c_cleanup_dma(priv);
456 txdesc->callback = rcar_i2c_dma_callback;
457 txdesc->callback_param = priv;
459 cookie = dmaengine_submit(txdesc);
460 if (dma_submit_error(cookie)) {
461 dev_dbg(dev, "submitting dma failed, using PIO\n");
462 rcar_i2c_cleanup_dma(priv);
466 /* Enable DMA Master Received/Transmitted */
468 rcar_i2c_write(priv, ICDMAER, RMDMAE);
470 rcar_i2c_write(priv, ICDMAER, TMDMAE);
472 dma_async_issue_pending(chan);
476 static void rcar_i2c_irq_send(struct rcar_i2c_priv *priv, u32 msr)
478 struct i2c_msg *msg = priv->msg;
480 /* FIXME: sometimes, unknown interrupt happened. Do nothing */
484 /* Check if DMA can be enabled and take over */
485 if (priv->pos == 1 && rcar_i2c_dma(priv))
488 if (priv->pos < msg->len) {
490 * Prepare next data to ICRXTX register.
491 * This data will go to _SHIFT_ register.
494 * [ICRXTX] -> [SHIFT] -> [I2C bus]
496 rcar_i2c_write(priv, ICRXTX, msg->buf[priv->pos]);
500 * The last data was pushed to ICRXTX on _PREV_ empty irq.
501 * It is on _SHIFT_ register, and will sent to I2C bus.
504 * [ICRXTX] -> [SHIFT] -> [I2C bus]
507 if (priv->flags & ID_LAST_MSG) {
509 * If current msg is the _LAST_ msg,
510 * prepare stop condition here.
511 * ID_DONE will be set on STOP irq.
513 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP);
515 rcar_i2c_next_msg(priv);
520 rcar_i2c_write(priv, ICMSR, RCAR_IRQ_ACK_SEND);
523 static void rcar_i2c_irq_recv(struct rcar_i2c_priv *priv, u32 msr)
525 struct i2c_msg *msg = priv->msg;
527 /* FIXME: sometimes, unknown interrupt happened. Do nothing */
533 * Address transfer phase finished, but no data at this point.
534 * Try to use DMA to receive data.
537 } else if (priv->pos < msg->len) {
538 /* get received data */
539 msg->buf[priv->pos] = rcar_i2c_read(priv, ICRXTX);
543 /* If next received data is the _LAST_, go to new phase. */
544 if (priv->pos + 1 == msg->len) {
545 if (priv->flags & ID_LAST_MSG) {
546 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_STOP);
548 rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_START);
549 priv->flags |= ID_P_REP_AFTER_RD;
553 if (priv->pos == msg->len && !(priv->flags & ID_LAST_MSG))
554 rcar_i2c_next_msg(priv);
556 rcar_i2c_write(priv, ICMSR, RCAR_IRQ_ACK_RECV);
559 static bool rcar_i2c_slave_irq(struct rcar_i2c_priv *priv)
561 u32 ssr_raw, ssr_filtered;
564 ssr_raw = rcar_i2c_read(priv, ICSSR) & 0xff;
565 ssr_filtered = ssr_raw & rcar_i2c_read(priv, ICSIER);
570 /* address detected */
571 if (ssr_filtered & SAR) {
572 /* read or write request */
574 i2c_slave_event(priv->slave, I2C_SLAVE_READ_REQUESTED, &value);
575 rcar_i2c_write(priv, ICRXTX, value);
576 rcar_i2c_write(priv, ICSIER, SDE | SSR | SAR);
578 i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
579 rcar_i2c_read(priv, ICRXTX); /* dummy read */
580 rcar_i2c_write(priv, ICSIER, SDR | SSR | SAR);
583 rcar_i2c_write(priv, ICSSR, ~SAR & 0xff);
586 /* master sent stop */
587 if (ssr_filtered & SSR) {
588 i2c_slave_event(priv->slave, I2C_SLAVE_STOP, &value);
589 rcar_i2c_write(priv, ICSIER, SAR | SSR);
590 rcar_i2c_write(priv, ICSSR, ~SSR & 0xff);
593 /* master wants to write to us */
594 if (ssr_filtered & SDR) {
597 value = rcar_i2c_read(priv, ICRXTX);
598 ret = i2c_slave_event(priv->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
599 /* Send NACK in case of error */
600 rcar_i2c_write(priv, ICSCR, SIE | SDBS | (ret < 0 ? FNA : 0));
601 rcar_i2c_write(priv, ICSSR, ~SDR & 0xff);
604 /* master wants to read from us */
605 if (ssr_filtered & SDE) {
606 i2c_slave_event(priv->slave, I2C_SLAVE_READ_PROCESSED, &value);
607 rcar_i2c_write(priv, ICRXTX, value);
608 rcar_i2c_write(priv, ICSSR, ~SDE & 0xff);
615 * This driver has a lock-free design because there are IP cores (at least
616 * R-Car Gen2) which have an inherent race condition in their hardware design.
617 * There, we need to clear RCAR_BUS_MASK_DATA bits as soon as possible after
618 * the interrupt was generated, otherwise an unwanted repeated message gets
619 * generated. It turned out that taking a spinlock at the beginning of the ISR
620 * was already causing repeated messages. Thus, this driver was converted to
621 * the now lockless behaviour. Please keep this in mind when hacking the driver.
623 static irqreturn_t rcar_i2c_irq(int irq, void *ptr)
625 struct rcar_i2c_priv *priv = ptr;
628 /* Clear START or STOP immediately, except for REPSTART after read */
629 if (likely(!(priv->flags & ID_P_REP_AFTER_RD))) {
630 val = rcar_i2c_read(priv, ICMCR);
631 rcar_i2c_write(priv, ICMCR, val & RCAR_BUS_MASK_DATA);
634 msr = rcar_i2c_read(priv, ICMSR);
636 /* Only handle interrupts that are currently enabled */
637 msr &= rcar_i2c_read(priv, ICMIER);
639 if (rcar_i2c_slave_irq(priv))
645 /* Arbitration lost */
647 priv->flags |= ID_DONE | ID_ARBLOST;
653 /* HW automatically sends STOP after received NACK */
654 rcar_i2c_write(priv, ICMIER, RCAR_IRQ_STOP);
655 priv->flags |= ID_NACK;
661 priv->msgs_left--; /* The last message also made it */
662 priv->flags |= ID_DONE;
666 if (rcar_i2c_is_recv(priv))
667 rcar_i2c_irq_recv(priv, msr);
669 rcar_i2c_irq_send(priv, msr);
672 if (priv->flags & ID_DONE) {
673 rcar_i2c_write(priv, ICMIER, 0);
674 rcar_i2c_write(priv, ICMSR, 0);
675 wake_up(&priv->wait);
681 static struct dma_chan *rcar_i2c_request_dma_chan(struct device *dev,
682 enum dma_transfer_direction dir,
683 dma_addr_t port_addr)
685 struct dma_chan *chan;
686 struct dma_slave_config cfg;
687 char *chan_name = dir == DMA_MEM_TO_DEV ? "tx" : "rx";
690 chan = dma_request_chan(dev, chan_name);
692 dev_dbg(dev, "request_channel failed for %s (%ld)\n",
693 chan_name, PTR_ERR(chan));
697 memset(&cfg, 0, sizeof(cfg));
699 if (dir == DMA_MEM_TO_DEV) {
700 cfg.dst_addr = port_addr;
701 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
703 cfg.src_addr = port_addr;
704 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
707 ret = dmaengine_slave_config(chan, &cfg);
709 dev_dbg(dev, "slave_config failed for %s (%d)\n",
711 dma_release_channel(chan);
715 dev_dbg(dev, "got DMA channel for %s\n", chan_name);
719 static void rcar_i2c_request_dma(struct rcar_i2c_priv *priv,
722 struct device *dev = rcar_i2c_priv_to_dev(priv);
724 struct dma_chan *chan;
725 enum dma_transfer_direction dir;
727 read = msg->flags & I2C_M_RD;
729 chan = read ? priv->dma_rx : priv->dma_tx;
730 if (PTR_ERR(chan) != -EPROBE_DEFER)
733 dir = read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV;
734 chan = rcar_i2c_request_dma_chan(dev, dir, priv->res->start + ICRXTX);
742 static void rcar_i2c_release_dma(struct rcar_i2c_priv *priv)
744 if (!IS_ERR(priv->dma_tx)) {
745 dma_release_channel(priv->dma_tx);
746 priv->dma_tx = ERR_PTR(-EPROBE_DEFER);
749 if (!IS_ERR(priv->dma_rx)) {
750 dma_release_channel(priv->dma_rx);
751 priv->dma_rx = ERR_PTR(-EPROBE_DEFER);
755 /* I2C is a special case, we need to poll the status of a reset */
756 static int rcar_i2c_do_reset(struct rcar_i2c_priv *priv)
760 ret = reset_control_reset(priv->rstc);
764 for (i = 0; i < LOOP_TIMEOUT; i++) {
765 ret = reset_control_status(priv->rstc);
774 static int rcar_i2c_master_xfer(struct i2c_adapter *adap,
775 struct i2c_msg *msgs,
778 struct rcar_i2c_priv *priv = i2c_get_adapdata(adap);
779 struct device *dev = rcar_i2c_priv_to_dev(priv);
783 pm_runtime_get_sync(dev);
785 /* Check bus state before init otherwise bus busy info will be lost */
786 ret = rcar_i2c_bus_barrier(priv);
790 /* Gen3 needs a reset before allowing RXDMA once */
791 if (priv->devtype == I2C_RCAR_GEN3) {
792 priv->flags |= ID_P_NO_RXDMA;
793 if (!IS_ERR(priv->rstc)) {
794 ret = rcar_i2c_do_reset(priv);
796 priv->flags &= ~ID_P_NO_RXDMA;
802 for (i = 0; i < num; i++)
803 rcar_i2c_request_dma(priv, msgs + i);
805 /* init first message */
807 priv->msgs_left = num;
808 priv->flags = (priv->flags & ID_P_MASK) | ID_FIRST_MSG;
809 rcar_i2c_prepare_msg(priv);
811 time_left = wait_event_timeout(priv->wait, priv->flags & ID_DONE,
812 num * adap->timeout);
814 /* cleanup DMA if it couldn't complete properly due to an error */
815 if (priv->dma_direction != DMA_NONE)
816 rcar_i2c_cleanup_dma(priv);
821 } else if (priv->flags & ID_NACK) {
823 } else if (priv->flags & ID_ARBLOST) {
826 ret = num - priv->msgs_left; /* The number of transfer */
831 if (ret < 0 && ret != -ENXIO)
832 dev_err(dev, "error %d : %x\n", ret, priv->flags);
837 static int rcar_reg_slave(struct i2c_client *slave)
839 struct rcar_i2c_priv *priv = i2c_get_adapdata(slave->adapter);
844 if (slave->flags & I2C_CLIENT_TEN)
845 return -EAFNOSUPPORT;
847 /* Keep device active for slave address detection logic */
848 pm_runtime_get_sync(rcar_i2c_priv_to_dev(priv));
851 rcar_i2c_write(priv, ICSAR, slave->addr);
852 rcar_i2c_write(priv, ICSSR, 0);
853 rcar_i2c_write(priv, ICSIER, SAR | SSR);
854 rcar_i2c_write(priv, ICSCR, SIE | SDBS);
859 static int rcar_unreg_slave(struct i2c_client *slave)
861 struct rcar_i2c_priv *priv = i2c_get_adapdata(slave->adapter);
863 WARN_ON(!priv->slave);
865 /* disable irqs and ensure none is running before clearing ptr */
866 rcar_i2c_write(priv, ICSIER, 0);
867 rcar_i2c_write(priv, ICSCR, 0);
869 synchronize_irq(priv->irq);
872 pm_runtime_put(rcar_i2c_priv_to_dev(priv));
877 static u32 rcar_i2c_func(struct i2c_adapter *adap)
881 * I2C_SMBUS_QUICK (setting FSB during START didn't work)
882 * I2C_M_NOSTART (automatically sends address after START)
883 * I2C_M_IGNORE_NAK (automatically sends STOP after NAK)
885 return I2C_FUNC_I2C | I2C_FUNC_SLAVE |
886 (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
889 static const struct i2c_algorithm rcar_i2c_algo = {
890 .master_xfer = rcar_i2c_master_xfer,
891 .functionality = rcar_i2c_func,
892 .reg_slave = rcar_reg_slave,
893 .unreg_slave = rcar_unreg_slave,
896 static const struct i2c_adapter_quirks rcar_i2c_quirks = {
897 .flags = I2C_AQ_NO_ZERO_LEN,
900 static const struct of_device_id rcar_i2c_dt_ids[] = {
901 { .compatible = "renesas,i2c-r8a7778", .data = (void *)I2C_RCAR_GEN1 },
902 { .compatible = "renesas,i2c-r8a7779", .data = (void *)I2C_RCAR_GEN1 },
903 { .compatible = "renesas,i2c-r8a7790", .data = (void *)I2C_RCAR_GEN2 },
904 { .compatible = "renesas,i2c-r8a7791", .data = (void *)I2C_RCAR_GEN2 },
905 { .compatible = "renesas,i2c-r8a7792", .data = (void *)I2C_RCAR_GEN2 },
906 { .compatible = "renesas,i2c-r8a7793", .data = (void *)I2C_RCAR_GEN2 },
907 { .compatible = "renesas,i2c-r8a7794", .data = (void *)I2C_RCAR_GEN2 },
908 { .compatible = "renesas,i2c-r8a7795", .data = (void *)I2C_RCAR_GEN3 },
909 { .compatible = "renesas,i2c-r8a7796", .data = (void *)I2C_RCAR_GEN3 },
910 { .compatible = "renesas,i2c-rcar", .data = (void *)I2C_RCAR_GEN1 }, /* Deprecated */
911 { .compatible = "renesas,rcar-gen1-i2c", .data = (void *)I2C_RCAR_GEN1 },
912 { .compatible = "renesas,rcar-gen2-i2c", .data = (void *)I2C_RCAR_GEN2 },
913 { .compatible = "renesas,rcar-gen3-i2c", .data = (void *)I2C_RCAR_GEN3 },
916 MODULE_DEVICE_TABLE(of, rcar_i2c_dt_ids);
918 static int rcar_i2c_probe(struct platform_device *pdev)
920 struct rcar_i2c_priv *priv;
921 struct i2c_adapter *adap;
922 struct device *dev = &pdev->dev;
923 struct i2c_timings i2c_t;
926 /* Otherwise logic will break because some bytes must always use PIO */
927 BUILD_BUG_ON_MSG(RCAR_MIN_DMA_LEN < 3, "Invalid min DMA length");
929 priv = devm_kzalloc(dev, sizeof(struct rcar_i2c_priv), GFP_KERNEL);
933 priv->clk = devm_clk_get(dev, NULL);
934 if (IS_ERR(priv->clk)) {
935 dev_err(dev, "cannot get clock\n");
936 return PTR_ERR(priv->clk);
939 priv->res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
941 priv->io = devm_ioremap_resource(dev, priv->res);
942 if (IS_ERR(priv->io))
943 return PTR_ERR(priv->io);
945 priv->devtype = (enum rcar_i2c_type)of_device_get_match_data(dev);
946 init_waitqueue_head(&priv->wait);
950 adap->algo = &rcar_i2c_algo;
951 adap->class = I2C_CLASS_DEPRECATED;
953 adap->dev.parent = dev;
954 adap->dev.of_node = dev->of_node;
955 adap->bus_recovery_info = &rcar_i2c_bri;
956 adap->quirks = &rcar_i2c_quirks;
957 i2c_set_adapdata(adap, priv);
958 strlcpy(adap->name, pdev->name, sizeof(adap->name));
960 i2c_parse_fw_timings(dev, &i2c_t, false);
963 sg_init_table(&priv->sg, 1);
964 priv->dma_direction = DMA_NONE;
965 priv->dma_rx = priv->dma_tx = ERR_PTR(-EPROBE_DEFER);
967 /* Activate device for clock calculation */
968 pm_runtime_enable(dev);
969 pm_runtime_get_sync(dev);
970 ret = rcar_i2c_clock_calculate(priv, &i2c_t);
974 if (priv->devtype == I2C_RCAR_GEN3) {
975 priv->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
976 if (!IS_ERR(priv->rstc)) {
977 ret = reset_control_status(priv->rstc);
979 priv->rstc = ERR_PTR(-ENOTSUPP);
983 /* Stay always active when multi-master to keep arbitration working */
984 if (of_property_read_bool(dev->of_node, "multi-master"))
985 priv->flags |= ID_P_PM_BLOCKED;
990 priv->irq = platform_get_irq(pdev, 0);
991 ret = devm_request_irq(dev, priv->irq, rcar_i2c_irq, 0, dev_name(dev), priv);
993 dev_err(dev, "cannot get irq %d\n", priv->irq);
997 platform_set_drvdata(pdev, priv);
999 ret = i2c_add_numbered_adapter(adap);
1001 goto out_pm_disable;
1003 dev_info(dev, "probed\n");
1008 pm_runtime_put(dev);
1010 pm_runtime_disable(dev);
1014 static int rcar_i2c_remove(struct platform_device *pdev)
1016 struct rcar_i2c_priv *priv = platform_get_drvdata(pdev);
1017 struct device *dev = &pdev->dev;
1019 i2c_del_adapter(&priv->adap);
1020 rcar_i2c_release_dma(priv);
1021 if (priv->flags & ID_P_PM_BLOCKED)
1022 pm_runtime_put(dev);
1023 pm_runtime_disable(dev);
1028 #ifdef CONFIG_PM_SLEEP
1029 static int rcar_i2c_suspend(struct device *dev)
1031 struct rcar_i2c_priv *priv = dev_get_drvdata(dev);
1033 i2c_mark_adapter_suspended(&priv->adap);
1037 static int rcar_i2c_resume(struct device *dev)
1039 struct rcar_i2c_priv *priv = dev_get_drvdata(dev);
1041 i2c_mark_adapter_resumed(&priv->adap);
1045 static const struct dev_pm_ops rcar_i2c_pm_ops = {
1046 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(rcar_i2c_suspend, rcar_i2c_resume)
1049 #define DEV_PM_OPS (&rcar_i2c_pm_ops)
1051 #define DEV_PM_OPS NULL
1052 #endif /* CONFIG_PM_SLEEP */
1054 static struct platform_driver rcar_i2c_driver = {
1057 .of_match_table = rcar_i2c_dt_ids,
1060 .probe = rcar_i2c_probe,
1061 .remove = rcar_i2c_remove,
1064 module_platform_driver(rcar_i2c_driver);
1066 MODULE_LICENSE("GPL v2");
1067 MODULE_DESCRIPTION("Renesas R-Car I2C bus driver");
1068 MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>");