drivers/i2c/busses/i2c-bcm-iproc.c

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 // Copyright (C) 2014 Broadcom Corporation
   3
   4 #include <linux/delay.h>
   5 #include <linux/i2c.h>
   6 #include <linux/interrupt.h>
   7 #include <linux/io.h>
   8 #include <linux/kernel.h>
   9 #include <linux/module.h>
  10 #include <linux/of_device.h>
  11 #include <linux/platform_device.h>
  12 #include <linux/slab.h>
  13
  14 #define IDM_CTRL_DIRECT_OFFSET       0x00
  15 #define CFG_OFFSET                   0x00
  16 #define CFG_RESET_SHIFT              31
  17 #define CFG_EN_SHIFT                 30
  18 #define CFG_SLAVE_ADDR_0_SHIFT       28
  19 #define CFG_M_RETRY_CNT_SHIFT        16
  20 #define CFG_M_RETRY_CNT_MASK         0x0f
  21
  22 #define TIM_CFG_OFFSET               0x04
  23 #define TIM_CFG_MODE_400_SHIFT       31
  24 #define TIM_RAND_SLAVE_STRETCH_SHIFT      24
  25 #define TIM_RAND_SLAVE_STRETCH_MASK       0x7f
  26 #define TIM_PERIODIC_SLAVE_STRETCH_SHIFT  16
  27 #define TIM_PERIODIC_SLAVE_STRETCH_MASK   0x7f
  28
  29 #define S_CFG_SMBUS_ADDR_OFFSET           0x08
  30 #define S_CFG_EN_NIC_SMB_ADDR3_SHIFT      31
  31 #define S_CFG_NIC_SMB_ADDR3_SHIFT         24
  32 #define S_CFG_NIC_SMB_ADDR3_MASK          0x7f
  33 #define S_CFG_EN_NIC_SMB_ADDR2_SHIFT      23
  34 #define S_CFG_NIC_SMB_ADDR2_SHIFT         16
  35 #define S_CFG_NIC_SMB_ADDR2_MASK          0x7f
  36 #define S_CFG_EN_NIC_SMB_ADDR1_SHIFT      15
  37 #define S_CFG_NIC_SMB_ADDR1_SHIFT         8
  38 #define S_CFG_NIC_SMB_ADDR1_MASK          0x7f
  39 #define S_CFG_EN_NIC_SMB_ADDR0_SHIFT      7
  40 #define S_CFG_NIC_SMB_ADDR0_SHIFT         0
  41 #define S_CFG_NIC_SMB_ADDR0_MASK          0x7f
  42
  43 #define M_FIFO_CTRL_OFFSET           0x0c
  44 #define M_FIFO_RX_FLUSH_SHIFT        31
  45 #define M_FIFO_TX_FLUSH_SHIFT        30
  46 #define M_FIFO_RX_CNT_SHIFT          16
  47 #define M_FIFO_RX_CNT_MASK           0x7f
  48 #define M_FIFO_RX_THLD_SHIFT         8
  49 #define M_FIFO_RX_THLD_MASK          0x3f
  50
  51 #define S_FIFO_CTRL_OFFSET           0x10
  52 #define S_FIFO_RX_FLUSH_SHIFT        31
  53 #define S_FIFO_TX_FLUSH_SHIFT        30
  54 #define S_FIFO_RX_CNT_SHIFT          16
  55 #define S_FIFO_RX_CNT_MASK           0x7f
  56 #define S_FIFO_RX_THLD_SHIFT         8
  57 #define S_FIFO_RX_THLD_MASK          0x3f
  58
  59 #define M_CMD_OFFSET                 0x30
  60 #define M_CMD_START_BUSY_SHIFT       31
  61 #define M_CMD_STATUS_SHIFT           25
  62 #define M_CMD_STATUS_MASK            0x07
  63 #define M_CMD_STATUS_SUCCESS         0x0
  64 #define M_CMD_STATUS_LOST_ARB        0x1
  65 #define M_CMD_STATUS_NACK_ADDR       0x2
  66 #define M_CMD_STATUS_NACK_DATA       0x3
  67 #define M_CMD_STATUS_TIMEOUT         0x4
  68 #define M_CMD_STATUS_FIFO_UNDERRUN   0x5
  69 #define M_CMD_STATUS_RX_FIFO_FULL    0x6
  70 #define M_CMD_PROTOCOL_SHIFT         9
  71 #define M_CMD_PROTOCOL_MASK          0xf
  72 #define M_CMD_PROTOCOL_QUICK         0x0
  73 #define M_CMD_PROTOCOL_BLK_WR        0x7
  74 #define M_CMD_PROTOCOL_BLK_RD        0x8
  75 #define M_CMD_PROTOCOL_PROCESS       0xa
  76 #define M_CMD_PEC_SHIFT              8
  77 #define M_CMD_RD_CNT_SHIFT           0
  78 #define M_CMD_RD_CNT_MASK            0xff
  79
  80 #define S_CMD_OFFSET                 0x34
  81 #define S_CMD_START_BUSY_SHIFT       31
  82 #define S_CMD_STATUS_SHIFT           23
  83 #define S_CMD_STATUS_MASK            0x07
  84 #define S_CMD_STATUS_SUCCESS         0x0
  85 #define S_CMD_STATUS_TIMEOUT         0x5
  86 #define S_CMD_STATUS_MASTER_ABORT    0x7
  87
  88 #define IE_OFFSET                    0x38
  89 #define IE_M_RX_FIFO_FULL_SHIFT      31
  90 #define IE_M_RX_THLD_SHIFT           30
  91 #define IE_M_START_BUSY_SHIFT        28
  92 #define IE_M_TX_UNDERRUN_SHIFT       27
  93 #define IE_S_RX_FIFO_FULL_SHIFT      26
  94 #define IE_S_RX_THLD_SHIFT           25
  95 #define IE_S_RX_EVENT_SHIFT          24
  96 #define IE_S_START_BUSY_SHIFT        23
  97 #define IE_S_TX_UNDERRUN_SHIFT       22
  98 #define IE_S_RD_EVENT_SHIFT          21
  99
 100 #define IS_OFFSET                    0x3c
 101 #define IS_M_RX_FIFO_FULL_SHIFT      31
 102 #define IS_M_RX_THLD_SHIFT           30
 103 #define IS_M_START_BUSY_SHIFT        28
 104 #define IS_M_TX_UNDERRUN_SHIFT       27
 105 #define IS_S_RX_FIFO_FULL_SHIFT      26
 106 #define IS_S_RX_THLD_SHIFT           25
 107 #define IS_S_RX_EVENT_SHIFT          24
 108 #define IS_S_START_BUSY_SHIFT        23
 109 #define IS_S_TX_UNDERRUN_SHIFT       22
 110 #define IS_S_RD_EVENT_SHIFT          21
 111
 112 #define M_TX_OFFSET                  0x40
 113 #define M_TX_WR_STATUS_SHIFT         31
 114 #define M_TX_DATA_SHIFT              0
 115 #define M_TX_DATA_MASK               0xff
 116
 117 #define M_RX_OFFSET                  0x44
 118 #define M_RX_STATUS_SHIFT            30
 119 #define M_RX_STATUS_MASK             0x03
 120 #define M_RX_PEC_ERR_SHIFT           29
 121 #define M_RX_DATA_SHIFT              0
 122 #define M_RX_DATA_MASK               0xff
 123
 124 #define S_TX_OFFSET                  0x48
 125 #define S_TX_WR_STATUS_SHIFT         31
 126 #define S_TX_DATA_SHIFT              0
 127 #define S_TX_DATA_MASK               0xff
 128
 129 #define S_RX_OFFSET                  0x4c
 130 #define S_RX_STATUS_SHIFT            30
 131 #define S_RX_STATUS_MASK             0x03
 132 #define S_RX_PEC_ERR_SHIFT           29
 133 #define S_RX_DATA_SHIFT              0
 134 #define S_RX_DATA_MASK               0xff
 135
 136 #define I2C_TIMEOUT_MSEC             50000
 137 #define M_TX_RX_FIFO_SIZE            64
 138 #define M_RX_FIFO_MAX_THLD_VALUE     (M_TX_RX_FIFO_SIZE - 1)
 139
 140 #define M_RX_MAX_READ_LEN            255
 141 #define M_RX_FIFO_THLD_VALUE         50
 142
 143 #define IE_M_ALL_INTERRUPT_SHIFT     27
 144 #define IE_M_ALL_INTERRUPT_MASK      0x1e
 145
 146 #define SLAVE_READ_WRITE_BIT_MASK    0x1
 147 #define SLAVE_READ_WRITE_BIT_SHIFT   0x1
 148 #define SLAVE_MAX_SIZE_TRANSACTION   64
 149 #define SLAVE_CLOCK_STRETCH_TIME     25
 150
 151 #define IE_S_ALL_INTERRUPT_SHIFT     21
 152 #define IE_S_ALL_INTERRUPT_MASK      0x3f
 153 /*
 154  * It takes ~18us to reading 10bytes of data, hence to keep tasklet
 155  * running for less time, max slave read per tasklet is set to 10 bytes.
 156  */
 157 #define MAX_SLAVE_RX_PER_INT         10
 158
 159 enum i2c_slave_read_status {
 160         I2C_SLAVE_RX_FIFO_EMPTY = 0,
 161         I2C_SLAVE_RX_START,
 162         I2C_SLAVE_RX_DATA,
 163         I2C_SLAVE_RX_END,
 164 };
 165
 166 enum bus_speed_index {
 167         I2C_SPD_100K = 0,
 168         I2C_SPD_400K,
 169 };
 170
 171 enum bcm_iproc_i2c_type {
 172         IPROC_I2C,
 173         IPROC_I2C_NIC
 174 };
 175
 176 struct bcm_iproc_i2c_dev {
 177         struct device *device;
 178         enum bcm_iproc_i2c_type type;
 179         int irq;
 180
 181         void __iomem *base;
 182         void __iomem *idm_base;
 183
 184         u32 ape_addr_mask;
 185
 186         /* lock for indirect access through IDM */
 187         spinlock_t idm_lock;
 188
 189         struct i2c_adapter adapter;
 190         unsigned int bus_speed;
 191
 192         struct completion done;
 193         int xfer_is_done;
 194
 195         struct i2c_msg *msg;
 196
 197         struct i2c_client *slave;
 198
 199         /* bytes that have been transferred */
 200         unsigned int tx_bytes;
 201         /* bytes that have been read */
 202         unsigned int rx_bytes;
 203         unsigned int thld_bytes;
 204
 205         bool slave_rx_only;
 206         bool rx_start_rcvd;
 207         bool slave_read_complete;
 208         u32 tx_underrun;
 209         u32 slave_int_mask;
 210         struct tasklet_struct slave_rx_tasklet;
 211 };
 212
 213 /* tasklet to process slave rx data */
 214 static void slave_rx_tasklet_fn(unsigned long);
 215
 216 /*
 217  * Can be expanded in the future if more interrupt status bits are utilized
 218  */
 219 #define ISR_MASK (BIT(IS_M_START_BUSY_SHIFT) | BIT(IS_M_TX_UNDERRUN_SHIFT)\
 220                 | BIT(IS_M_RX_THLD_SHIFT))
 221
 222 #define ISR_MASK_SLAVE (BIT(IS_S_START_BUSY_SHIFT)\
 223                 | BIT(IS_S_RX_EVENT_SHIFT) | BIT(IS_S_RD_EVENT_SHIFT)\
 224                 | BIT(IS_S_TX_UNDERRUN_SHIFT) | BIT(IS_S_RX_FIFO_FULL_SHIFT)\
 225                 | BIT(IS_S_RX_THLD_SHIFT))
 226
 227 static int bcm_iproc_i2c_reg_slave(struct i2c_client *slave);
 228 static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave);
 229 static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c,
 230                                          bool enable);
 231
 232 static inline u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
 233                                    u32 offset)
 234 {
 235         u32 val;
 236         unsigned long flags;
 237
 238         if (iproc_i2c->idm_base) {
 239                 spin_lock_irqsave(&iproc_i2c->idm_lock, flags);
 240                 writel(iproc_i2c->ape_addr_mask,
 241                        iproc_i2c->idm_base + IDM_CTRL_DIRECT_OFFSET);
 242                 val = readl(iproc_i2c->base + offset);
 243                 spin_unlock_irqrestore(&iproc_i2c->idm_lock, flags);
 244         } else {
 245                 val = readl(iproc_i2c->base + offset);
 246         }
 247
 248         return val;
 249 }
 250
 251 static inline void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
 252                                     u32 offset, u32 val)
 253 {
 254         unsigned long flags;
 255
 256         if (iproc_i2c->idm_base) {
 257                 spin_lock_irqsave(&iproc_i2c->idm_lock, flags);
 258                 writel(iproc_i2c->ape_addr_mask,
 259                        iproc_i2c->idm_base + IDM_CTRL_DIRECT_OFFSET);
 260                 writel(val, iproc_i2c->base + offset);
 261                 spin_unlock_irqrestore(&iproc_i2c->idm_lock, flags);
 262         } else {
 263                 writel(val, iproc_i2c->base + offset);
 264         }
 265 }
 266
 267 static void bcm_iproc_i2c_slave_init(
 268         struct bcm_iproc_i2c_dev *iproc_i2c, bool need_reset)
 269 {
 270         u32 val;
 271
 272         iproc_i2c->tx_underrun = 0;
 273         if (need_reset) {
 274                 /* put controller in reset */
 275                 val = iproc_i2c_rd_reg(iproc_i2c, CFG_OFFSET);
 276                 val |= BIT(CFG_RESET_SHIFT);
 277                 iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 278
 279                 /* wait 100 usec per spec */
 280                 udelay(100);
 281
 282                 /* bring controller out of reset */
 283                 val &= ~(BIT(CFG_RESET_SHIFT));
 284                 iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 285         }
 286
 287         /* flush TX/RX FIFOs */
 288         val = (BIT(S_FIFO_RX_FLUSH_SHIFT) | BIT(S_FIFO_TX_FLUSH_SHIFT));
 289         iproc_i2c_wr_reg(iproc_i2c, S_FIFO_CTRL_OFFSET, val);
 290
 291         /* Maximum slave stretch time */
 292         val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
 293         val &= ~(TIM_RAND_SLAVE_STRETCH_MASK << TIM_RAND_SLAVE_STRETCH_SHIFT);
 294         val |= (SLAVE_CLOCK_STRETCH_TIME << TIM_RAND_SLAVE_STRETCH_SHIFT);
 295         iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
 296
 297         /* Configure the slave address */
 298         val = iproc_i2c_rd_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET);
 299         val |= BIT(S_CFG_EN_NIC_SMB_ADDR3_SHIFT);
 300         val &= ~(S_CFG_NIC_SMB_ADDR3_MASK << S_CFG_NIC_SMB_ADDR3_SHIFT);
 301         val |= (iproc_i2c->slave->addr << S_CFG_NIC_SMB_ADDR3_SHIFT);
 302         iproc_i2c_wr_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET, val);
 303
 304         /* clear all pending slave interrupts */
 305         iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, ISR_MASK_SLAVE);
 306
 307         /* Enable interrupt register to indicate a valid byte in receive fifo */
 308         val = BIT(IE_S_RX_EVENT_SHIFT);
 309         /* Enable interrupt register to indicate Slave Rx FIFO Full */
 310         val |= BIT(IE_S_RX_FIFO_FULL_SHIFT);
 311         /* Enable interrupt register to indicate a Master read transaction */
 312         val |= BIT(IE_S_RD_EVENT_SHIFT);
 313         /* Enable interrupt register for the Slave BUSY command */
 314         val |= BIT(IE_S_START_BUSY_SHIFT);
 315         iproc_i2c->slave_int_mask = val;
 316         iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
 317 }
 318
 319 static void bcm_iproc_i2c_check_slave_status(
 320         struct bcm_iproc_i2c_dev *iproc_i2c)
 321 {
 322         u32 val;
 323
 324         val = iproc_i2c_rd_reg(iproc_i2c, S_CMD_OFFSET);
 325         /* status is valid only when START_BUSY is cleared after it was set */
 326         if (val & BIT(S_CMD_START_BUSY_SHIFT))
 327                 return;
 328
 329         val = (val >> S_CMD_STATUS_SHIFT) & S_CMD_STATUS_MASK;
 330         if (val == S_CMD_STATUS_TIMEOUT || val == S_CMD_STATUS_MASTER_ABORT) {
 331                 dev_err(iproc_i2c->device, (val == S_CMD_STATUS_TIMEOUT) ?
 332                         "slave random stretch time timeout\n" :
 333                         "Master aborted read transaction\n");
 334                 /* re-initialize i2c for recovery */
 335                 bcm_iproc_i2c_enable_disable(iproc_i2c, false);
 336                 bcm_iproc_i2c_slave_init(iproc_i2c, true);
 337                 bcm_iproc_i2c_enable_disable(iproc_i2c, true);
 338         }
 339 }
 340
 341 static void bcm_iproc_i2c_slave_read(struct bcm_iproc_i2c_dev *iproc_i2c)
 342 {
 343         u8 rx_data, rx_status;
 344         u32 rx_bytes = 0;
 345         u32 val;
 346
 347         while (rx_bytes < MAX_SLAVE_RX_PER_INT) {
 348                 val = iproc_i2c_rd_reg(iproc_i2c, S_RX_OFFSET);
 349                 rx_status = (val >> S_RX_STATUS_SHIFT) & S_RX_STATUS_MASK;
 350                 rx_data = ((val >> S_RX_DATA_SHIFT) & S_RX_DATA_MASK);
 351
 352                 if (rx_status == I2C_SLAVE_RX_START) {
 353                         /* Start of SMBUS Master write */
 354                         i2c_slave_event(iproc_i2c->slave,
 355                                         I2C_SLAVE_WRITE_REQUESTED, &rx_data);
 356                         iproc_i2c->rx_start_rcvd = true;
 357                         iproc_i2c->slave_read_complete = false;
 358                 } else if (rx_status == I2C_SLAVE_RX_DATA &&
 359                            iproc_i2c->rx_start_rcvd) {
 360                         /* Middle of SMBUS Master write */
 361                         i2c_slave_event(iproc_i2c->slave,
 362                                         I2C_SLAVE_WRITE_RECEIVED, &rx_data);
 363                 } else if (rx_status == I2C_SLAVE_RX_END &&
 364                            iproc_i2c->rx_start_rcvd) {
 365                         /* End of SMBUS Master write */
 366                         if (iproc_i2c->slave_rx_only)
 367                                 i2c_slave_event(iproc_i2c->slave,
 368                                                 I2C_SLAVE_WRITE_RECEIVED,
 369                                                 &rx_data);
 370
 371                         i2c_slave_event(iproc_i2c->slave, I2C_SLAVE_STOP,
 372                                         &rx_data);
 373                 } else if (rx_status == I2C_SLAVE_RX_FIFO_EMPTY) {
 374                         iproc_i2c->rx_start_rcvd = false;
 375                         iproc_i2c->slave_read_complete = true;
 376                         break;
 377                 }
 378
 379                 rx_bytes++;
 380         }
 381 }
 382
 383 static void slave_rx_tasklet_fn(unsigned long data)
 384 {
 385         struct bcm_iproc_i2c_dev *iproc_i2c = (struct bcm_iproc_i2c_dev *)data;
 386         u32 int_clr;
 387
 388         bcm_iproc_i2c_slave_read(iproc_i2c);
 389
 390         /* clear pending IS_S_RX_EVENT_SHIFT interrupt */
 391         int_clr = BIT(IS_S_RX_EVENT_SHIFT);
 392
 393         if (!iproc_i2c->slave_rx_only && iproc_i2c->slave_read_complete) {
 394                 /*
 395                  * In case of single byte master-read request,
 396                  * IS_S_TX_UNDERRUN_SHIFT event is generated before
 397                  * IS_S_START_BUSY_SHIFT event. Hence start slave data send
 398                  * from first IS_S_TX_UNDERRUN_SHIFT event.
 399                  *
 400                  * This means don't send any data from slave when
 401                  * IS_S_RD_EVENT_SHIFT event is generated else it will increment
 402                  * eeprom or other backend slave driver read pointer twice.
 403                  */
 404                 iproc_i2c->tx_underrun = 0;
 405                 iproc_i2c->slave_int_mask |= BIT(IE_S_TX_UNDERRUN_SHIFT);
 406
 407                 /* clear IS_S_RD_EVENT_SHIFT interrupt */
 408                 int_clr |= BIT(IS_S_RD_EVENT_SHIFT);
 409         }
 410
 411         /* clear slave interrupt */
 412         iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, int_clr);
 413         /* enable slave interrupts */
 414         iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, iproc_i2c->slave_int_mask);
 415 }
 416
 417 static bool bcm_iproc_i2c_slave_isr(struct bcm_iproc_i2c_dev *iproc_i2c,
 418                                     u32 status)
 419 {
 420         u32 val;
 421         u8 value;
 422
 423         /*
 424          * Slave events in case of master-write, master-write-read and,
 425          * master-read
 426          *
 427          * Master-write     : only IS_S_RX_EVENT_SHIFT event
 428          * Master-write-read: both IS_S_RX_EVENT_SHIFT and IS_S_RD_EVENT_SHIFT
 429          *                    events
 430          * Master-read      : both IS_S_RX_EVENT_SHIFT and IS_S_RD_EVENT_SHIFT
 431          *                    events or only IS_S_RD_EVENT_SHIFT
 432          *
 433          * iproc has a slave rx fifo size of 64 bytes. Rx fifo full interrupt
 434          * (IS_S_RX_FIFO_FULL_SHIFT) will be generated when RX fifo becomes
 435          * full. This can happen if Master issues write requests of more than
 436          * 64 bytes.
 437          */
 438         if (status & BIT(IS_S_RX_EVENT_SHIFT) ||
 439             status & BIT(IS_S_RD_EVENT_SHIFT) ||
 440             status & BIT(IS_S_RX_FIFO_FULL_SHIFT)) {
 441                 /* disable slave interrupts */
 442                 val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 443                 val &= ~iproc_i2c->slave_int_mask;
 444                 iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
 445
 446                 if (status & BIT(IS_S_RD_EVENT_SHIFT))
 447                         /* Master-write-read request */
 448                         iproc_i2c->slave_rx_only = false;
 449                 else
 450                         /* Master-write request only */
 451                         iproc_i2c->slave_rx_only = true;
 452
 453                 /* schedule tasklet to read data later */
 454                 tasklet_schedule(&iproc_i2c->slave_rx_tasklet);
 455
 456                 /*
 457                  * clear only IS_S_RX_EVENT_SHIFT and
 458                  * IS_S_RX_FIFO_FULL_SHIFT interrupt.
 459                  */
 460                 val = BIT(IS_S_RX_EVENT_SHIFT);
 461                 if (status & BIT(IS_S_RX_FIFO_FULL_SHIFT))
 462                         val |= BIT(IS_S_RX_FIFO_FULL_SHIFT);
 463                 iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, val);
 464         }
 465
 466         if (status & BIT(IS_S_TX_UNDERRUN_SHIFT)) {
 467                 iproc_i2c->tx_underrun++;
 468                 if (iproc_i2c->tx_underrun == 1)
 469                         /* Start of SMBUS for Master Read */
 470                         i2c_slave_event(iproc_i2c->slave,
 471                                         I2C_SLAVE_READ_REQUESTED,
 472                                         &value);
 473                 else
 474                         /* Master read other than start */
 475                         i2c_slave_event(iproc_i2c->slave,
 476                                         I2C_SLAVE_READ_PROCESSED,
 477                                         &value);
 478
 479                 iproc_i2c_wr_reg(iproc_i2c, S_TX_OFFSET, value);
 480                 /* start transfer */
 481                 val = BIT(S_CMD_START_BUSY_SHIFT);
 482                 iproc_i2c_wr_reg(iproc_i2c, S_CMD_OFFSET, val);
 483
 484                 /* clear interrupt */
 485                 iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET,
 486                                  BIT(IS_S_TX_UNDERRUN_SHIFT));
 487         }
 488
 489         /* Stop received from master in case of master read transaction */
 490         if (status & BIT(IS_S_START_BUSY_SHIFT)) {
 491                 /*
 492                  * Disable interrupt for TX FIFO becomes empty and
 493                  * less than PKT_LENGTH bytes were output on the SMBUS
 494                  */
 495                 iproc_i2c->slave_int_mask &= ~BIT(IE_S_TX_UNDERRUN_SHIFT);
 496                 iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET,
 497                                  iproc_i2c->slave_int_mask);
 498
 499                 /* End of SMBUS for Master Read */
 500                 val = BIT(S_TX_WR_STATUS_SHIFT);
 501                 iproc_i2c_wr_reg(iproc_i2c, S_TX_OFFSET, val);
 502
 503                 val = BIT(S_CMD_START_BUSY_SHIFT);
 504                 iproc_i2c_wr_reg(iproc_i2c, S_CMD_OFFSET, val);
 505
 506                 /* flush TX FIFOs */
 507                 val = iproc_i2c_rd_reg(iproc_i2c, S_FIFO_CTRL_OFFSET);
 508                 val |= (BIT(S_FIFO_TX_FLUSH_SHIFT));
 509                 iproc_i2c_wr_reg(iproc_i2c, S_FIFO_CTRL_OFFSET, val);
 510
 511                 i2c_slave_event(iproc_i2c->slave, I2C_SLAVE_STOP, &value);
 512
 513                 /* clear interrupt */
 514                 iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET,
 515                                  BIT(IS_S_START_BUSY_SHIFT));
 516         }
 517
 518         /* check slave transmit status only if slave is transmitting */
 519         if (!iproc_i2c->slave_rx_only)
 520                 bcm_iproc_i2c_check_slave_status(iproc_i2c);
 521
 522         return true;
 523 }
 524
 525 static void bcm_iproc_i2c_read_valid_bytes(struct bcm_iproc_i2c_dev *iproc_i2c)
 526 {
 527         struct i2c_msg *msg = iproc_i2c->msg;
 528         uint32_t val;
 529
 530         /* Read valid data from RX FIFO */
 531         while (iproc_i2c->rx_bytes < msg->len) {
 532                 val = iproc_i2c_rd_reg(iproc_i2c, M_RX_OFFSET);
 533
 534                 /* rx fifo empty */
 535                 if (!((val >> M_RX_STATUS_SHIFT) & M_RX_STATUS_MASK))
 536                         break;
 537
 538                 msg->buf[iproc_i2c->rx_bytes] =
 539                         (val >> M_RX_DATA_SHIFT) & M_RX_DATA_MASK;
 540                 iproc_i2c->rx_bytes++;
 541         }
 542 }
 543
 544 static void bcm_iproc_i2c_send(struct bcm_iproc_i2c_dev *iproc_i2c)
 545 {
 546         struct i2c_msg *msg = iproc_i2c->msg;
 547         unsigned int tx_bytes = msg->len - iproc_i2c->tx_bytes;
 548         unsigned int i;
 549         u32 val;
 550
 551         /* can only fill up to the FIFO size */
 552         tx_bytes = min_t(unsigned int, tx_bytes, M_TX_RX_FIFO_SIZE);
 553         for (i = 0; i < tx_bytes; i++) {
 554                 /* start from where we left over */
 555                 unsigned int idx = iproc_i2c->tx_bytes + i;
 556
 557                 val = msg->buf[idx];
 558
 559                 /* mark the last byte */
 560                 if (idx == msg->len - 1) {
 561                         val |= BIT(M_TX_WR_STATUS_SHIFT);
 562
 563                         if (iproc_i2c->irq) {
 564                                 u32 tmp;
 565
 566                                 /*
 567                                  * Since this is the last byte, we should now
 568                                  * disable TX FIFO underrun interrupt
 569                                  */
 570                                 tmp = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 571                                 tmp &= ~BIT(IE_M_TX_UNDERRUN_SHIFT);
 572                                 iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET,
 573                                                  tmp);
 574                         }
 575                 }
 576
 577                 /* load data into TX FIFO */
 578                 iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, val);
 579         }
 580
 581         /* update number of transferred bytes */
 582         iproc_i2c->tx_bytes += tx_bytes;
 583 }
 584
 585 static void bcm_iproc_i2c_read(struct bcm_iproc_i2c_dev *iproc_i2c)
 586 {
 587         struct i2c_msg *msg = iproc_i2c->msg;
 588         u32 bytes_left, val;
 589
 590         bcm_iproc_i2c_read_valid_bytes(iproc_i2c);
 591         bytes_left = msg->len - iproc_i2c->rx_bytes;
 592         if (bytes_left == 0) {
 593                 if (iproc_i2c->irq) {
 594                         /* finished reading all data, disable rx thld event */
 595                         val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 596                         val &= ~BIT(IS_M_RX_THLD_SHIFT);
 597                         iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
 598                 }
 599         } else if (bytes_left < iproc_i2c->thld_bytes) {
 600                 /* set bytes left as threshold */
 601                 val = iproc_i2c_rd_reg(iproc_i2c, M_FIFO_CTRL_OFFSET);
 602                 val &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
 603                 val |= (bytes_left << M_FIFO_RX_THLD_SHIFT);
 604                 iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
 605                 iproc_i2c->thld_bytes = bytes_left;
 606         }
 607         /*
 608          * bytes_left >= iproc_i2c->thld_bytes,
 609          * hence no need to change the THRESHOLD SET.
 610          * It will remain as iproc_i2c->thld_bytes itself
 611          */
 612 }
 613
 614 static void bcm_iproc_i2c_process_m_event(struct bcm_iproc_i2c_dev *iproc_i2c,
 615                                           u32 status)
 616 {
 617         /* TX FIFO is empty and we have more data to send */
 618         if (status & BIT(IS_M_TX_UNDERRUN_SHIFT))
 619                 bcm_iproc_i2c_send(iproc_i2c);
 620
 621         /* RX FIFO threshold is reached and data needs to be read out */
 622         if (status & BIT(IS_M_RX_THLD_SHIFT))
 623                 bcm_iproc_i2c_read(iproc_i2c);
 624
 625         /* transfer is done */
 626         if (status & BIT(IS_M_START_BUSY_SHIFT)) {
 627                 iproc_i2c->xfer_is_done = 1;
 628                 if (iproc_i2c->irq)
 629                         complete(&iproc_i2c->done);
 630         }
 631 }
 632
 633 static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
 634 {
 635         struct bcm_iproc_i2c_dev *iproc_i2c = data;
 636         u32 slave_status;
 637         u32 status;
 638         bool ret;
 639
 640         status = iproc_i2c_rd_reg(iproc_i2c, IS_OFFSET);
 641         /* process only slave interrupt which are enabled */
 642         slave_status = status & iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET) &
 643                        ISR_MASK_SLAVE;
 644
 645         if (slave_status) {
 646                 ret = bcm_iproc_i2c_slave_isr(iproc_i2c, slave_status);
 647                 if (ret)
 648                         return IRQ_HANDLED;
 649                 else
 650                         return IRQ_NONE;
 651         }
 652
 653         status &= ISR_MASK;
 654         if (!status)
 655                 return IRQ_NONE;
 656
 657         /* process all master based events */
 658         bcm_iproc_i2c_process_m_event(iproc_i2c, status);
 659         iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, status);
 660
 661         return IRQ_HANDLED;
 662 }
 663
 664 static int bcm_iproc_i2c_init(struct bcm_iproc_i2c_dev *iproc_i2c)
 665 {
 666         u32 val;
 667
 668         /* put controller in reset */
 669         val = iproc_i2c_rd_reg(iproc_i2c, CFG_OFFSET);
 670         val |= BIT(CFG_RESET_SHIFT);
 671         val &= ~(BIT(CFG_EN_SHIFT));
 672         iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 673
 674         /* wait 100 usec per spec */
 675         udelay(100);
 676
 677         /* bring controller out of reset */
 678         val &= ~(BIT(CFG_RESET_SHIFT));
 679         iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 680
 681         /* flush TX/RX FIFOs and set RX FIFO threshold to zero */
 682         val = (BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT));
 683         iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
 684         /* disable all interrupts */
 685         val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 686         val &= ~(IE_M_ALL_INTERRUPT_MASK <<
 687                         IE_M_ALL_INTERRUPT_SHIFT);
 688         iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
 689
 690         /* clear all pending interrupts */
 691         iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, 0xffffffff);
 692
 693         return 0;
 694 }
 695
 696 static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c,
 697                                          bool enable)
 698 {
 699         u32 val;
 700
 701         val = iproc_i2c_rd_reg(iproc_i2c, CFG_OFFSET);
 702         if (enable)
 703                 val |= BIT(CFG_EN_SHIFT);
 704         else
 705                 val &= ~BIT(CFG_EN_SHIFT);
 706         iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
 707 }
 708
 709 static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c,
 710                                       struct i2c_msg *msg)
 711 {
 712         u32 val;
 713
 714         val = iproc_i2c_rd_reg(iproc_i2c, M_CMD_OFFSET);
 715         val = (val >> M_CMD_STATUS_SHIFT) & M_CMD_STATUS_MASK;
 716
 717         switch (val) {
 718         case M_CMD_STATUS_SUCCESS:
 719                 return 0;
 720
 721         case M_CMD_STATUS_LOST_ARB:
 722                 dev_dbg(iproc_i2c->device, "lost bus arbitration\n");
 723                 return -EAGAIN;
 724
 725         case M_CMD_STATUS_NACK_ADDR:
 726                 dev_dbg(iproc_i2c->device, "NAK addr:0x%02x\n", msg->addr);
 727                 return -ENXIO;
 728
 729         case M_CMD_STATUS_NACK_DATA:
 730                 dev_dbg(iproc_i2c->device, "NAK data\n");
 731                 return -ENXIO;
 732
 733         case M_CMD_STATUS_TIMEOUT:
 734                 dev_dbg(iproc_i2c->device, "bus timeout\n");
 735                 return -ETIMEDOUT;
 736
 737         case M_CMD_STATUS_FIFO_UNDERRUN:
 738                 dev_dbg(iproc_i2c->device, "FIFO under-run\n");
 739                 return -ENXIO;
 740
 741         case M_CMD_STATUS_RX_FIFO_FULL:
 742                 dev_dbg(iproc_i2c->device, "RX FIFO full\n");
 743                 return -ETIMEDOUT;
 744
 745         default:
 746                 dev_dbg(iproc_i2c->device, "unknown error code=%d\n", val);
 747
 748                 /* re-initialize i2c for recovery */
 749                 bcm_iproc_i2c_enable_disable(iproc_i2c, false);
 750                 bcm_iproc_i2c_init(iproc_i2c);
 751                 bcm_iproc_i2c_enable_disable(iproc_i2c, true);
 752
 753                 return -EIO;
 754         }
 755 }
 756
 757 static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
 758                                    struct i2c_msg *msg,
 759                                    u32 cmd)
 760 {
 761         unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT_MSEC);
 762         u32 val, status;
 763         int ret;
 764
 765         iproc_i2c_wr_reg(iproc_i2c, M_CMD_OFFSET, cmd);
 766
 767         if (iproc_i2c->irq) {
 768                 time_left = wait_for_completion_timeout(&iproc_i2c->done,
 769                                                         time_left);
 770                 /* disable all interrupts */
 771                 iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, 0);
 772                 /* read it back to flush the write */
 773                 iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
 774                 /* make sure the interrupt handler isn't running */
 775                 synchronize_irq(iproc_i2c->irq);
 776
 777         } else { /* polling mode */
 778                 unsigned long timeout = jiffies + time_left;
 779
 780                 do {
 781                         status = iproc_i2c_rd_reg(iproc_i2c,
 782                                                   IS_OFFSET) & ISR_MASK;
 783                         bcm_iproc_i2c_process_m_event(iproc_i2c, status);
 784                         iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, status);
 785
 786                         if (time_after(jiffies, timeout)) {
 787                                 time_left = 0;
 788                                 break;
 789                         }
 790
 791                         cpu_relax();
 792                         cond_resched();
 793                 } while (!iproc_i2c->xfer_is_done);
 794         }
 795
 796         if (!time_left && !iproc_i2c->xfer_is_done) {
 797                 dev_err(iproc_i2c->device, "transaction timed out\n");
 798
 799                 /* flush both TX/RX FIFOs */
 800                 val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
 801                 iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
 802                 return -ETIMEDOUT;
 803         }
 804
 805         ret = bcm_iproc_i2c_check_status(iproc_i2c, msg);
 806         if (ret) {
 807                 /* flush both TX/RX FIFOs */
 808                 val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
 809                 iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
 810                 return ret;
 811         }
 812
 813         return 0;
 814 }
 815
 816 /*
 817  * If 'process_call' is true, then this is a multi-msg transfer that requires
 818  * a repeated start between the messages.
 819  * More specifically, it must be a write (reg) followed by a read (data).
 820  * The i2c quirks are set to enforce this rule.
 821  */
 822 static int bcm_iproc_i2c_xfer_internal(struct bcm_iproc_i2c_dev *iproc_i2c,
 823                                         struct i2c_msg *msgs, bool process_call)
 824 {
 825         int i;
 826         u8 addr;
 827         u32 val, tmp, val_intr_en;
 828         unsigned int tx_bytes;
 829         struct i2c_msg *msg = &msgs[0];
 830
 831         /* check if bus is busy */
 832         if (!!(iproc_i2c_rd_reg(iproc_i2c,
 833                                 M_CMD_OFFSET) & BIT(M_CMD_START_BUSY_SHIFT))) {
 834                 dev_warn(iproc_i2c->device, "bus is busy\n");
 835                 return -EBUSY;
 836         }
 837
 838         iproc_i2c->msg = msg;
 839
 840         /* format and load slave address into the TX FIFO */
 841         addr = i2c_8bit_addr_from_msg(msg);
 842         iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, addr);
 843
 844         /*
 845          * For a write transaction, load data into the TX FIFO. Only allow
 846          * loading up to TX FIFO size - 1 bytes of data since the first byte
 847          * has been used up by the slave address
 848          */
 849         tx_bytes = min_t(unsigned int, msg->len, M_TX_RX_FIFO_SIZE - 1);
 850         if (!(msg->flags & I2C_M_RD)) {
 851                 for (i = 0; i < tx_bytes; i++) {
 852                         val = msg->buf[i];
 853
 854                         /* mark the last byte */
 855                         if (!process_call && (i == msg->len - 1))
 856                                 val |= BIT(M_TX_WR_STATUS_SHIFT);
 857
 858                         iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, val);
 859                 }
 860                 iproc_i2c->tx_bytes = tx_bytes;
 861         }
 862
 863         /* Process the read message if this is process call */
 864         if (process_call) {
 865                 msg++;
 866                 iproc_i2c->msg = msg;  /* point to second msg */
 867
 868                 /*
 869                  * The last byte to be sent out should be a slave
 870                  * address with read operation
 871                  */
 872                 addr = i2c_8bit_addr_from_msg(msg);
 873                 /* mark it the last byte out */
 874                 val = addr | BIT(M_TX_WR_STATUS_SHIFT);
 875                 iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, val);
 876         }
 877
 878         /* mark as incomplete before starting the transaction */
 879         if (iproc_i2c->irq)
 880                 reinit_completion(&iproc_i2c->done);
 881
 882         iproc_i2c->xfer_is_done = 0;
 883
 884         /*
 885          * Enable the "start busy" interrupt, which will be triggered after the
 886          * transaction is done, i.e., the internal start_busy bit, transitions
 887          * from 1 to 0.
 888          */
 889         val_intr_en = BIT(IE_M_START_BUSY_SHIFT);
 890
 891         /*
 892          * If TX data size is larger than the TX FIFO, need to enable TX
 893          * underrun interrupt, which will be triggerred when the TX FIFO is
 894          * empty. When that happens we can then pump more data into the FIFO
 895          */
 896         if (!process_call && !(msg->flags & I2C_M_RD) &&
 897             msg->len > iproc_i2c->tx_bytes)
 898                 val_intr_en |= BIT(IE_M_TX_UNDERRUN_SHIFT);
 899
 900         /*
 901          * Now we can activate the transfer. For a read operation, specify the
 902          * number of bytes to read
 903          */
 904         val = BIT(M_CMD_START_BUSY_SHIFT);
 905
 906         if (msg->len == 0) {
 907                 /* SMBUS QUICK Command (Read/Write) */
 908                 val |= (M_CMD_PROTOCOL_QUICK << M_CMD_PROTOCOL_SHIFT);
 909         } else if (msg->flags & I2C_M_RD) {
 910                 u32 protocol;
 911
 912                 iproc_i2c->rx_bytes = 0;
 913                 if (msg->len > M_RX_FIFO_MAX_THLD_VALUE)
 914                         iproc_i2c->thld_bytes = M_RX_FIFO_THLD_VALUE;
 915                 else
 916                         iproc_i2c->thld_bytes = msg->len;
 917
 918                 /* set threshold value */
 919                 tmp = iproc_i2c_rd_reg(iproc_i2c, M_FIFO_CTRL_OFFSET);
 920                 tmp &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
 921                 tmp |= iproc_i2c->thld_bytes << M_FIFO_RX_THLD_SHIFT;
 922                 iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, tmp);
 923
 924                 /* enable the RX threshold interrupt */
 925                 val_intr_en |= BIT(IE_M_RX_THLD_SHIFT);
 926
 927                 protocol = process_call ?
 928                                 M_CMD_PROTOCOL_PROCESS : M_CMD_PROTOCOL_BLK_RD;
 929
 930                 val |= (protocol << M_CMD_PROTOCOL_SHIFT) |
 931                        (msg->len << M_CMD_RD_CNT_SHIFT);
 932         } else {
 933                 val |= (M_CMD_PROTOCOL_BLK_WR << M_CMD_PROTOCOL_SHIFT);
 934         }
 935
 936         if (iproc_i2c->irq)
 937                 iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val_intr_en);
 938
 939         return bcm_iproc_i2c_xfer_wait(iproc_i2c, msg, val);
 940 }
 941
 942 static int bcm_iproc_i2c_xfer(struct i2c_adapter *adapter,
 943                               struct i2c_msg msgs[], int num)
 944 {
 945         struct bcm_iproc_i2c_dev *iproc_i2c = i2c_get_adapdata(adapter);
 946         bool process_call = false;
 947         int ret;
 948
 949         if (num == 2) {
 950                 /* Repeated start, use process call */
 951                 process_call = true;
 952                 if (msgs[1].flags & I2C_M_NOSTART) {
 953                         dev_err(iproc_i2c->device, "Invalid repeated start\n");
 954                         return -EOPNOTSUPP;
 955                 }
 956         }
 957
 958         ret = bcm_iproc_i2c_xfer_internal(iproc_i2c, msgs, process_call);
 959         if (ret) {
 960                 dev_dbg(iproc_i2c->device, "xfer failed\n");
 961                 return ret;
 962         }
 963
 964         return num;
 965 }
 966
 967 static uint32_t bcm_iproc_i2c_functionality(struct i2c_adapter *adap)
 968 {
 969         u32 val;
 970
 971         val = I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
 972
 973         if (adap->algo->reg_slave)
 974                 val |= I2C_FUNC_SLAVE;
 975
 976         return val;
 977 }
 978
 979 static struct i2c_algorithm bcm_iproc_algo = {
 980         .master_xfer = bcm_iproc_i2c_xfer,
 981         .functionality = bcm_iproc_i2c_functionality,
 982         .reg_slave = bcm_iproc_i2c_reg_slave,
 983         .unreg_slave = bcm_iproc_i2c_unreg_slave,
 984 };
 985
 986 static const struct i2c_adapter_quirks bcm_iproc_i2c_quirks = {
 987         .flags = I2C_AQ_COMB_WRITE_THEN_READ,
 988         .max_comb_1st_msg_len = M_TX_RX_FIFO_SIZE,
 989         .max_read_len = M_RX_MAX_READ_LEN,
 990 };
 991
 992 static int bcm_iproc_i2c_cfg_speed(struct bcm_iproc_i2c_dev *iproc_i2c)
 993 {
 994         unsigned int bus_speed;
 995         u32 val;
 996         int ret = of_property_read_u32(iproc_i2c->device->of_node,
 997                                        "clock-frequency", &bus_speed);
 998         if (ret < 0) {
 999                 dev_info(iproc_i2c->device,
1000                         "unable to interpret clock-frequency DT property\n");
1001                 bus_speed = I2C_MAX_STANDARD_MODE_FREQ;
1002         }
1003
1004         if (bus_speed < I2C_MAX_STANDARD_MODE_FREQ) {
1005                 dev_err(iproc_i2c->device, "%d Hz bus speed not supported\n",
1006                         bus_speed);
1007                 dev_err(iproc_i2c->device,
1008                         "valid speeds are 100khz and 400khz\n");
1009                 return -EINVAL;
1010         } else if (bus_speed < I2C_MAX_FAST_MODE_FREQ) {
1011                 bus_speed = I2C_MAX_STANDARD_MODE_FREQ;
1012         } else {
1013                 bus_speed = I2C_MAX_FAST_MODE_FREQ;
1014         }
1015
1016         iproc_i2c->bus_speed = bus_speed;
1017         val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
1018         val &= ~BIT(TIM_CFG_MODE_400_SHIFT);
1019         val |= (bus_speed == I2C_MAX_FAST_MODE_FREQ) << TIM_CFG_MODE_400_SHIFT;
1020         iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
1021
1022         dev_info(iproc_i2c->device, "bus set to %u Hz\n", bus_speed);
1023
1024         return 0;
1025 }
1026
1027 static int bcm_iproc_i2c_probe(struct platform_device *pdev)
1028 {
1029         int irq, ret = 0;
1030         struct bcm_iproc_i2c_dev *iproc_i2c;
1031         struct i2c_adapter *adap;
1032         struct resource *res;
1033
1034         iproc_i2c = devm_kzalloc(&pdev->dev, sizeof(*iproc_i2c),
1035                                  GFP_KERNEL);
1036         if (!iproc_i2c)
1037                 return -ENOMEM;
1038
1039         platform_set_drvdata(pdev, iproc_i2c);
1040         iproc_i2c->device = &pdev->dev;
1041         iproc_i2c->type =
1042                 (enum bcm_iproc_i2c_type)of_device_get_match_data(&pdev->dev);
1043         init_completion(&iproc_i2c->done);
1044
1045         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1046         iproc_i2c->base = devm_ioremap_resource(iproc_i2c->device, res);
1047         if (IS_ERR(iproc_i2c->base))
1048                 return PTR_ERR(iproc_i2c->base);
1049
1050         if (iproc_i2c->type == IPROC_I2C_NIC) {
1051                 res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
1052                 iproc_i2c->idm_base = devm_ioremap_resource(iproc_i2c->device,
1053                                                             res);
1054                 if (IS_ERR(iproc_i2c->idm_base))
1055                         return PTR_ERR(iproc_i2c->idm_base);
1056
1057                 ret = of_property_read_u32(iproc_i2c->device->of_node,
1058                                            "brcm,ape-hsls-addr-mask",
1059                                            &iproc_i2c->ape_addr_mask);
1060                 if (ret < 0) {
1061                         dev_err(iproc_i2c->device,
1062                                 "'brcm,ape-hsls-addr-mask' missing\n");
1063                         return -EINVAL;
1064                 }
1065
1066                 spin_lock_init(&iproc_i2c->idm_lock);
1067
1068                 /* no slave support */
1069                 bcm_iproc_algo.reg_slave = NULL;
1070                 bcm_iproc_algo.unreg_slave = NULL;
1071         }
1072
1073         ret = bcm_iproc_i2c_init(iproc_i2c);
1074         if (ret)
1075                 return ret;
1076
1077         ret = bcm_iproc_i2c_cfg_speed(iproc_i2c);
1078         if (ret)
1079                 return ret;
1080
1081         irq = platform_get_irq(pdev, 0);
1082         if (irq > 0) {
1083                 ret = devm_request_irq(iproc_i2c->device, irq,
1084                                        bcm_iproc_i2c_isr, 0, pdev->name,
1085                                        iproc_i2c);
1086                 if (ret < 0) {
1087                         dev_err(iproc_i2c->device,
1088                                 "unable to request irq %i\n", irq);
1089                         return ret;
1090                 }
1091
1092                 iproc_i2c->irq = irq;
1093         } else {
1094                 dev_warn(iproc_i2c->device,
1095                          "no irq resource, falling back to poll mode\n");
1096         }
1097
1098         bcm_iproc_i2c_enable_disable(iproc_i2c, true);
1099
1100         adap = &iproc_i2c->adapter;
1101         i2c_set_adapdata(adap, iproc_i2c);
1102         snprintf(adap->name, sizeof(adap->name),
1103                 "Broadcom iProc (%s)",
1104                 of_node_full_name(iproc_i2c->device->of_node));
1105         adap->algo = &bcm_iproc_algo;
1106         adap->quirks = &bcm_iproc_i2c_quirks;
1107         adap->dev.parent = &pdev->dev;
1108         adap->dev.of_node = pdev->dev.of_node;
1109
1110         return i2c_add_adapter(adap);
1111 }
1112
1113 static void bcm_iproc_i2c_remove(struct platform_device *pdev)
1114 {
1115         struct bcm_iproc_i2c_dev *iproc_i2c = platform_get_drvdata(pdev);
1116
1117         if (iproc_i2c->irq) {
1118                 /*
1119                  * Make sure there's no pending interrupt when we remove the
1120                  * adapter
1121                  */
1122                 iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, 0);
1123                 iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
1124                 synchronize_irq(iproc_i2c->irq);
1125         }
1126
1127         i2c_del_adapter(&iproc_i2c->adapter);
1128         bcm_iproc_i2c_enable_disable(iproc_i2c, false);
1129 }
1130
1131 #ifdef CONFIG_PM_SLEEP
1132
1133 static int bcm_iproc_i2c_suspend(struct device *dev)
1134 {
1135         struct bcm_iproc_i2c_dev *iproc_i2c = dev_get_drvdata(dev);
1136
1137         if (iproc_i2c->irq) {
1138                 /*
1139                  * Make sure there's no pending interrupt when we go into
1140                  * suspend
1141                  */
1142                 iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, 0);
1143                 iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
1144                 synchronize_irq(iproc_i2c->irq);
1145         }
1146
1147         /* now disable the controller */
1148         bcm_iproc_i2c_enable_disable(iproc_i2c, false);
1149
1150         return 0;
1151 }
1152
1153 static int bcm_iproc_i2c_resume(struct device *dev)
1154 {
1155         struct bcm_iproc_i2c_dev *iproc_i2c = dev_get_drvdata(dev);
1156         int ret;
1157         u32 val;
1158
1159         /*
1160          * Power domain could have been shut off completely in system deep
1161          * sleep, so re-initialize the block here
1162          */
1163         ret = bcm_iproc_i2c_init(iproc_i2c);
1164         if (ret)
1165                 return ret;
1166
1167         /* configure to the desired bus speed */
1168         val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
1169         val &= ~BIT(TIM_CFG_MODE_400_SHIFT);
1170         val |= (iproc_i2c->bus_speed == I2C_MAX_FAST_MODE_FREQ) << TIM_CFG_MODE_400_SHIFT;
1171         iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
1172
1173         bcm_iproc_i2c_enable_disable(iproc_i2c, true);
1174
1175         return 0;
1176 }
1177
1178 static const struct dev_pm_ops bcm_iproc_i2c_pm_ops = {
1179         .suspend_late = &bcm_iproc_i2c_suspend,
1180         .resume_early = &bcm_iproc_i2c_resume
1181 };
1182
1183 #define BCM_IPROC_I2C_PM_OPS (&bcm_iproc_i2c_pm_ops)
1184 #else
1185 #define BCM_IPROC_I2C_PM_OPS NULL
1186 #endif /* CONFIG_PM_SLEEP */
1187
1188
1189 static int bcm_iproc_i2c_reg_slave(struct i2c_client *slave)
1190 {
1191         struct bcm_iproc_i2c_dev *iproc_i2c = i2c_get_adapdata(slave->adapter);
1192
1193         if (iproc_i2c->slave)
1194                 return -EBUSY;
1195
1196         if (slave->flags & I2C_CLIENT_TEN)
1197                 return -EAFNOSUPPORT;
1198
1199         iproc_i2c->slave = slave;
1200
1201         tasklet_init(&iproc_i2c->slave_rx_tasklet, slave_rx_tasklet_fn,
1202                      (unsigned long)iproc_i2c);
1203
1204         bcm_iproc_i2c_slave_init(iproc_i2c, false);
1205         return 0;
1206 }
1207
1208 static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave)
1209 {
1210         u32 tmp;
1211         struct bcm_iproc_i2c_dev *iproc_i2c = i2c_get_adapdata(slave->adapter);
1212
1213         if (!iproc_i2c->slave)
1214                 return -EINVAL;
1215
1216         disable_irq(iproc_i2c->irq);
1217
1218         tasklet_kill(&iproc_i2c->slave_rx_tasklet);
1219
1220         /* disable all slave interrupts */
1221         tmp = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
1222         tmp &= ~(IE_S_ALL_INTERRUPT_MASK <<
1223                         IE_S_ALL_INTERRUPT_SHIFT);
1224         iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, tmp);
1225
1226         /* Erase the slave address programmed */
1227         tmp = iproc_i2c_rd_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET);
1228         tmp &= ~BIT(S_CFG_EN_NIC_SMB_ADDR3_SHIFT);
1229         iproc_i2c_wr_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET, tmp);
1230
1231         /* flush TX/RX FIFOs */
1232         tmp = (BIT(S_FIFO_RX_FLUSH_SHIFT) | BIT(S_FIFO_TX_FLUSH_SHIFT));
1233         iproc_i2c_wr_reg(iproc_i2c, S_FIFO_CTRL_OFFSET, tmp);
1234
1235         /* clear all pending slave interrupts */
1236         iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, ISR_MASK_SLAVE);
1237
1238         iproc_i2c->slave = NULL;
1239
1240         enable_irq(iproc_i2c->irq);
1241
1242         return 0;
1243 }
1244
1245 static const struct of_device_id bcm_iproc_i2c_of_match[] = {
1246         {
1247                 .compatible = "brcm,iproc-i2c",
1248                 .data = (int *)IPROC_I2C,
1249         }, {
1250                 .compatible = "brcm,iproc-nic-i2c",
1251                 .data = (int *)IPROC_I2C_NIC,
1252         },
1253         { /* sentinel */ }
1254 };
1255 MODULE_DEVICE_TABLE(of, bcm_iproc_i2c_of_match);
1256
1257 static struct platform_driver bcm_iproc_i2c_driver = {
1258         .driver = {
1259                 .name = "bcm-iproc-i2c",
1260                 .of_match_table = bcm_iproc_i2c_of_match,
1261                 .pm = BCM_IPROC_I2C_PM_OPS,
1262         },
1263         .probe = bcm_iproc_i2c_probe,
1264         .remove_new = bcm_iproc_i2c_remove,
1265 };
1266 module_platform_driver(bcm_iproc_i2c_driver);
1267
1268 MODULE_AUTHOR("Ray Jui <rjui@broadcom.com>");
1269 MODULE_DESCRIPTION("Broadcom iProc I2C Driver");
1270 MODULE_LICENSE("GPL v2");