2 # Boot count configuration
5 menuconfig BOOTCOUNT_LIMIT
6 bool "Enable support for checking boot count limit"
8 Enable checking for exceeding the boot count limit.
9 More information: http://www.denx.de/wiki/DULG/UBootBootCountLimit
14 prompt "Boot count device"
15 default BOOTCOUNT_AM33XX if AM33XX || SOC_DA8XX
16 default BOOTCOUNT_AT91 if AT91SAM9XE
17 default BOOTCOUNT_GENERIC
19 config BOOTCOUNT_GENERIC
20 bool "Generic default boot counter"
22 Generic bootcount stored at SYS_BOOTCOUNT_ADDR.
25 Set to the address where the bootcount and bootcount magic
29 bool "Boot counter on EXT filesystem"
33 Add support for maintaining boot count in a file on an EXT
36 config BOOTCOUNT_AM33XX
37 bool "Boot counter in AM33XX RTC IP block"
38 depends on AM33XX || SOC_DA8XX
39 select SPL_AM33XX_ENABLE_RTC32K_OSC if AM33XX
41 A bootcount driver for the RTC IP block found on many TI platforms.
42 This requires the RTC clocks, etc, to be enabled prior to use and
43 not all boards with this IP block on it will have the RTC in use.
45 config BOOTCOUNT_AM33XX_NVMEM
46 bool "Boot counter in AM33XX RTC IP block with upgrade_available flag"
48 select SPL_AM33XX_ENABLE_RTC32K_OSC if AM33XX
50 Add support for maintaining bootcount,upgrade_available,
51 version and BOOTMAGIC in a AM33xx RTC IP block
54 A bootcount driver for the RTC IP block found on many TI platforms.
55 This requires the RTC clocks, etc, to be enabled prior to use and
56 not all boards with this IP block on it will have the RTC in use.
58 If there is upgrade in software then "upgrade_available" is 1,
59 "bootcount" is incremented otherwise "upgrade_available" and
60 "bootcount" is always 0. So the Userspace Application must set
61 the "upgrade_available" and "bootcount" variable to 0, if a boot
65 bool "Boot counter in environment"
67 If no softreset save registers are found on the hardware
68 "bootcount" is stored in the environment. To prevent a
69 saveenv on all reboots, the environment variable
70 "upgrade_available" is used. If "upgrade_available" is
71 0, "bootcount" is always 0, if "upgrade_available" is
72 1 "bootcount" is incremented in the environment.
73 So the Userspace Application must set the "upgrade_available"
74 and "bootcount" variable to 0, if a boot was successfully.
77 bool "Boot counter in RAM"
79 Store the bootcount in DRAM protected against against bit errors
80 due to short power loss or holding a system in RESET.
83 bool "Boot counter on I2C device"
85 Enable support for the bootcounter on an i2c (like RTC) device.
86 CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
87 CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
91 bool "Boot counter for Atmel AT91SAM9XE"
95 bool "Boot counter in a device-model device"
97 Enables reading/writing the bootcount in a device-model based
98 backing store. If an entry in /chosen/u-boot,bootcount-device
99 exists, this will be the preferred bootcount device; otherwise
100 the first available bootcount device will be used.
106 menu "Backing stores for device-model backed bootcount"
107 config DM_BOOTCOUNT_RTC
108 bool "Support RTC devices as a backing store for bootcount"
111 Enabled reading/writing the bootcount in a DM RTC device.
112 The wrapper device is to be specified with the compatible string
113 'u-boot,bootcount-rtc' and the 'rtc'-property (a phandle pointing
114 to the underlying RTC device) and an optional 'offset' property
117 Accesses to the backing store are performed using the write16
118 and read16 ops of DM RTC devices.
120 config DM_BOOTCOUNT_I2C_EEPROM
121 bool "Support i2c eeprom devices as a backing store for bootcount"
122 depends on I2C_EEPROM
124 Enabled reading/writing the bootcount in a DM i2c eeprom device.
125 The wrapper device is to be specified with the compatible string
126 'u-boot,bootcount-i2c-eeprom' and the 'i2c-eeprom'-property (a phandle
127 pointing to the underlying i2c eeprom device) and an optional 'offset'
128 property are supported.
130 config DM_BOOTCOUNT_PMIC_PFUZE100
131 bool "Enable Bootcount driver for PMIC PFUZE100"
132 depends on DM_PMIC_PFUZE100
134 Enable support for the bootcounter using PMIC PFUZE100 registers.
135 This works only, if the PMIC is not connected.
137 config DM_BOOTCOUNT_SPI_FLASH
138 bool "Support SPI flash devices as a backing store for bootcount"
139 depends on DM_SPI_FLASH
141 Enabled reading/writing the bootcount in a DM SPI flash device.
142 The wrapper device is to be specified with the compatible string
143 'u-boot,bootcount-spi-flash' and the 'spi-flash'-property (a phandle
144 pointing to the underlying SPI flash device) and an optional 'offset'
145 property are supported.
148 bool "Support memory based bootcounter"
150 Enabling Memory based bootcount, typically in a SoC register which
151 is not cleared on softreset.
152 compatible = "u-boot,bootcount";
154 config DM_BOOTCOUNT_SYSCON
155 bool "Support SYSCON devices as a backing store for bootcount"
159 Enable reading/writing the bootcount value in a DM SYSCON device.
160 The driver supports a fixed 32 bits size register using the native
161 endianness. However, this can be controlled from the SYSCON DT node
164 Accessing the backend is done using the regmap interface.
170 config BOOTCOUNT_BOOTLIMIT
171 int "Maximum number of reboot cycles allowed"
174 Set the Maximum number of reboot cycles allowed without the boot
175 counter being cleared.
176 If set to 0 do not set a boot limit in the environment.
178 config BOOTCOUNT_ALEN
179 int "I2C address length"
181 depends on BOOTCOUNT_I2C
183 Length of the the I2C address at SYS_BOOTCOUNT_ADDR for storing
186 config SYS_BOOTCOUNT_SINGLEWORD
187 bool "Use single word to pack boot count and magic value"
188 depends on BOOTCOUNT_GENERIC
190 This option enables packing boot count magic value and boot count
191 into single word (32 bits).
193 config SYS_BOOTCOUNT_EXT_INTERFACE
194 string "Interface on which to find boot counter EXT filesystem"
196 depends on BOOTCOUNT_EXT
198 Set the interface to use when locating the filesystem to use for the
201 config SYS_BOOTCOUNT_EXT_DEVPART
202 string "Partition of the boot counter EXT filesystem"
204 depends on BOOTCOUNT_EXT
206 Set the partition to use when locating the filesystem to use for the
209 config SYS_BOOTCOUNT_EXT_NAME
210 string "Path and filename of the EXT filesystem based boot counter"
211 default "/boot/failures"
212 depends on BOOTCOUNT_EXT
214 Set the filename and path of the file used to store the boot counter.
216 config SYS_BOOTCOUNT_ADDR
217 hex "RAM address used for reading and writing the boot counter"
218 default 0x44E3E000 if BOOTCOUNT_AM33XX || BOOTCOUNT_AM33XX_NVMEM
219 default 0xE0115FF8 if ARCH_LS1043A || ARCH_LS1021A
220 depends on BOOTCOUNT_AM33XX || BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
221 BOOTCOUNT_I2C || BOOTCOUNT_AM33XX_NVMEM
223 Set the address used for reading and writing the boot counter.
225 config SYS_BOOTCOUNT_MAGIC
226 hex "Magic value for the boot counter"
227 default 0xB001C041 if BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
228 BOOTCOUNT_AM33XX || BOOTCOUNT_ENV || \
229 BOOTCOUNT_RAM || BOOTCOUNT_I2C || \
230 BOOTCOUNT_AT91 || DM_BOOTCOUNT
231 default 0xB0 if BOOTCOUNT_AM33XX_NVMEM
232 depends on BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
233 BOOTCOUNT_AM33XX || BOOTCOUNT_ENV || \
234 BOOTCOUNT_RAM || BOOTCOUNT_I2C || \
235 BOOTCOUNT_AT91 || DM_BOOTCOUNT || \
236 BOOTCOUNT_AM33XX_NVMEM
238 Set the magic value used for the boot counter.