drivers/atm/nicstarmac.c

   1 /*
   2  * this file included by nicstar.c
   3  */
   4
   5 /*
   6  * nicstarmac.c
   7  * Read this ForeRunner's MAC address from eprom/eeprom
   8  */
   9
  10 #include <linux/kernel.h>
  11
  12 typedef void __iomem *virt_addr_t;
  13
  14 #define CYCLE_DELAY 5
  15
  16 /*
  17    This was the original definition
  18 #define osp_MicroDelay(microsec) \
  19     do { int _i = 4*microsec; while (--_i > 0) { __SLOW_DOWN_IO; }} while (0)
  20 */
  21 #define osp_MicroDelay(microsec) {unsigned long useconds = (microsec); \
  22                                   udelay((useconds));}
  23 /*
  24  * The following tables represent the timing diagrams found in
  25  * the Data Sheet for the Xicor X25020 EEProm.  The #defines below
  26  * represent the bits in the NICStAR's General Purpose register
  27  * that must be toggled for the corresponding actions on the EEProm
  28  * to occur.
  29  */
  30
  31 /* Write Data To EEProm from SI line on rising edge of CLK */
  32 /* Read Data From EEProm on falling edge of CLK */
  33
  34 #define CS_HIGH         0x0002  /* Chip select high */
  35 #define CS_LOW          0x0000  /* Chip select low (active low) */
  36 #define CLK_HIGH        0x0004  /* Clock high */
  37 #define CLK_LOW         0x0000  /* Clock low  */
  38 #define SI_HIGH         0x0001  /* Serial input data high */
  39 #define SI_LOW          0x0000  /* Serial input data low */
  40
  41 /* Read Status Register = 0000 0101b */
  42 #if 0
  43 static u_int32_t rdsrtab[] = {
  44         CS_HIGH | CLK_HIGH,
  45         CS_LOW | CLK_LOW,
  46         CLK_HIGH,               /* 0 */
  47         CLK_LOW,
  48         CLK_HIGH,               /* 0 */
  49         CLK_LOW,
  50         CLK_HIGH,               /* 0 */
  51         CLK_LOW,
  52         CLK_HIGH,               /* 0 */
  53         CLK_LOW,
  54         CLK_HIGH,               /* 0 */
  55         CLK_LOW | SI_HIGH,
  56         CLK_HIGH | SI_HIGH,     /* 1 */
  57         CLK_LOW | SI_LOW,
  58         CLK_HIGH,               /* 0 */
  59         CLK_LOW | SI_HIGH,
  60         CLK_HIGH | SI_HIGH      /* 1 */
  61 };
  62 #endif /*  0  */
  63
  64 /* Read from EEPROM = 0000 0011b */
  65 static u_int32_t readtab[] = {
  66         /*
  67            CS_HIGH | CLK_HIGH,
  68          */
  69         CS_LOW | CLK_LOW,
  70         CLK_HIGH,               /* 0 */
  71         CLK_LOW,
  72         CLK_HIGH,               /* 0 */
  73         CLK_LOW,
  74         CLK_HIGH,               /* 0 */
  75         CLK_LOW,
  76         CLK_HIGH,               /* 0 */
  77         CLK_LOW,
  78         CLK_HIGH,               /* 0 */
  79         CLK_LOW,
  80         CLK_HIGH,               /* 0 */
  81         CLK_LOW | SI_HIGH,
  82         CLK_HIGH | SI_HIGH,     /* 1 */
  83         CLK_LOW | SI_HIGH,
  84         CLK_HIGH | SI_HIGH      /* 1 */
  85 };
  86
  87 /* Clock to read from/write to the eeprom */
  88 static u_int32_t clocktab[] = {
  89         CLK_LOW,
  90         CLK_HIGH,
  91         CLK_LOW,
  92         CLK_HIGH,
  93         CLK_LOW,
  94         CLK_HIGH,
  95         CLK_LOW,
  96         CLK_HIGH,
  97         CLK_LOW,
  98         CLK_HIGH,
  99         CLK_LOW,
 100         CLK_HIGH,
 101         CLK_LOW,
 102         CLK_HIGH,
 103         CLK_LOW,
 104         CLK_HIGH,
 105         CLK_LOW
 106 };
 107
 108 #define NICSTAR_REG_WRITE(bs, reg, val) \
 109         while ( readl(bs + STAT) & 0x0200 ) ; \
 110         writel((val),(base)+(reg))
 111 #define NICSTAR_REG_READ(bs, reg) \
 112         readl((base)+(reg))
 113 #define NICSTAR_REG_GENERAL_PURPOSE GP
 114
 115 /*
 116  * This routine will clock the Read_Status_reg function into the X2520
 117  * eeprom, then pull the result from bit 16 of the NicSTaR's General Purpose
 118  * register.
 119  */
 120 #if 0
 121 u_int32_t nicstar_read_eprom_status(virt_addr_t base)
 122 {
 123         u_int32_t val;
 124         u_int32_t rbyte;
 125         int32_t i, j;
 126
 127         /* Send read instruction */
 128         val = NICSTAR_REG_READ(base, NICSTAR_REG_GENERAL_PURPOSE) & 0xFFFFFFF0;
 129
 130         for (i = 0; i < ARRAY_SIZE(rdsrtab); i++) {
 131                 NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 132                                   (val | rdsrtab[i]));
 133                 osp_MicroDelay(CYCLE_DELAY);
 134         }
 135
 136         /* Done sending instruction - now pull data off of bit 16, MSB first */
 137         /* Data clocked out of eeprom on falling edge of clock */
 138
 139         rbyte = 0;
 140         for (i = 7, j = 0; i >= 0; i--) {
 141                 NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 142                                   (val | clocktab[j++]));
 143                 rbyte |= (((NICSTAR_REG_READ(base, NICSTAR_REG_GENERAL_PURPOSE)
 144                             & 0x00010000) >> 16) << i);
 145                 NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 146                                   (val | clocktab[j++]));
 147                 osp_MicroDelay(CYCLE_DELAY);
 148         }
 149         NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE, 2);
 150         osp_MicroDelay(CYCLE_DELAY);
 151         return rbyte;
 152 }
 153 #endif /*  0  */
 154
 155 /*
 156  * This routine will clock the Read_data function into the X2520
 157  * eeprom, followed by the address to read from, through the NicSTaR's General
 158  * Purpose register.
 159  */
 160
 161 static u_int8_t read_eprom_byte(virt_addr_t base, u_int8_t offset)
 162 {
 163         u_int32_t val = 0;
 164         int i, j = 0;
 165         u_int8_t tempread = 0;
 166
 167         val = NICSTAR_REG_READ(base, NICSTAR_REG_GENERAL_PURPOSE) & 0xFFFFFFF0;
 168
 169         /* Send READ instruction */
 170         for (i = 0; i < ARRAY_SIZE(readtab); i++) {
 171                 NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 172                                   (val | readtab[i]));
 173                 osp_MicroDelay(CYCLE_DELAY);
 174         }
 175
 176         /* Next, we need to send the byte address to read from */
 177         for (i = 7; i >= 0; i--) {
 178                 NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 179                                   (val | clocktab[j++] | ((offset >> i) & 1)));
 180                 osp_MicroDelay(CYCLE_DELAY);
 181                 NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 182                                   (val | clocktab[j++] | ((offset >> i) & 1)));
 183                 osp_MicroDelay(CYCLE_DELAY);
 184         }
 185
 186         j = 0;
 187
 188         /* Now, we can read data from the eeprom by clocking it in */
 189         for (i = 7; i >= 0; i--) {
 190                 NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 191                                   (val | clocktab[j++]));
 192                 osp_MicroDelay(CYCLE_DELAY);
 193                 tempread |=
 194                     (((NICSTAR_REG_READ(base, NICSTAR_REG_GENERAL_PURPOSE)
 195                        & 0x00010000) >> 16) << i);
 196                 NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 197                                   (val | clocktab[j++]));
 198                 osp_MicroDelay(CYCLE_DELAY);
 199         }
 200
 201         NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE, 2);
 202         osp_MicroDelay(CYCLE_DELAY);
 203         return tempread;
 204 }
 205
 206 static void nicstar_init_eprom(virt_addr_t base)
 207 {
 208         u_int32_t val;
 209
 210         /*
 211          * turn chip select off
 212          */
 213         val = NICSTAR_REG_READ(base, NICSTAR_REG_GENERAL_PURPOSE) & 0xFFFFFFF0;
 214
 215         NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 216                           (val | CS_HIGH | CLK_HIGH));
 217         osp_MicroDelay(CYCLE_DELAY);
 218
 219         NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 220                           (val | CS_HIGH | CLK_LOW));
 221         osp_MicroDelay(CYCLE_DELAY);
 222
 223         NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 224                           (val | CS_HIGH | CLK_HIGH));
 225         osp_MicroDelay(CYCLE_DELAY);
 226
 227         NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
 228                           (val | CS_HIGH | CLK_LOW));
 229         osp_MicroDelay(CYCLE_DELAY);
 230 }
 231
 232 /*
 233  * This routine will be the interface to the ReadPromByte function
 234  * above.
 235  */
 236
 237 static void
 238 nicstar_read_eprom(virt_addr_t base,
 239                    u_int8_t prom_offset, u_int8_t * buffer, u_int32_t nbytes)
 240 {
 241         u_int i;
 242
 243         for (i = 0; i < nbytes; i++) {
 244                 buffer[i] = read_eprom_byte(base, prom_offset);
 245                 ++prom_offset;
 246                 osp_MicroDelay(CYCLE_DELAY);
 247         }
 248 }