1 U-Boot for UniPhier SoC family
2 ==============================
8 (a) Ubuntu packages (CROSS_COMPILE=arm-linux-gnueabi-)
10 If you are building U-Boot on Ubuntu, its standard package is recommended.
11 You can install it as follows:
13 $ sudo apt-get install gcc-arm-linux-gnueabi-
15 (b) Linaro compilers (CROSS_COMPILE=arm-linux-gnueabihf-)
17 You can download pre-built toolchains from:
19 http://www.linaro.org/downloads/
21 (c) kernel.org compilers (CROSS_COMPILE=arm-unknown-linux-gnueabi-)
23 You can download pre-built toolchains from:
25 ftp://www.kernel.org/pub/tools/crosstool/files/bin/
31 PH1-sLD3 reference board:
32 $ make uniphier_sld3_defconfig
33 $ make CROSS_COMPILE=arm-linux-gnueabi-
35 PH1-LD4 reference board:
36 $ make uniphier_ld4_sld8_defconfig
37 $ make CROSS_COMPILE=arm-linux-gnueabi-
39 PH1-sLD8 reference board:
40 $ make uniphier_ld4_sld8_defconfig
41 $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-sld8-ref
43 PH1-Pro4 reference board:
44 $ make uniphier_pro4_defconfig
45 $ make CROSS_COMPILE=arm-linux-gnueabi-
48 $ make uniphier_pro4_defconfig
49 $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-pro4-ace
52 $ make uniphier_pro4_defconfig
53 $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-pro4-sanji
56 $ make uniphier_pxs2_ld6b_defconfig
57 $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-pro5-4kbox
59 ProXstream2 Gentil board:
60 $ make uniphier_pxs2_ld6b_defconfig
61 $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-proxstream2-gentil
63 ProXstream2 Vodka board:
64 $ make uniphier_pxs2_ld6b_defconfig
65 $ make CROSS_COMPILE=arm-linux-gnueabi-
67 PH1-LD6b reference board:
68 $ make uniphier_pxs2_ld6b_defconfig
69 $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-ld6b-ref
71 You may wish to change the "CROSS_COMPILE=arm-linux-gnueabi-"
72 to use your favorite compiler.
75 Burn U-Boot images to NAND
76 --------------------------
78 Write two files to the NAND device as follows:
79 - spl/u-boot-spl.bin at the offset address 0x00000000
80 - u-boot.img at the offset address 0x00010000
82 If a TFTP server is available, the images can be easily updated.
83 Just copy the u-boot-spl.bin and u-boot.img to the TFTP public directory,
84 and then run the following command at the U-Boot command line:
89 Burn U-Boot images to eMMC
90 --------------------------
92 Write two files to the Boot partition 1 of the eMMC device as follows:
93 - spl/u-boot-spl.bin at the offset address 0x00000000
94 - u-boot.img at the offset address 0x00010000
96 If a TFTP server is available, the images can be easily updated.
97 Just copy the u-boot-spl.bin and u-boot.img to the TFTP public directory,
98 and then run the following command at the U-Boot command line:
103 UniPhier specific commands
104 --------------------------
106 - pinmon (enabled by CONFIG_CMD_PINMON)
107 shows the boot mode pins that has been latched at the power-on reset
109 - ddrphy (enabled by CONFIG_CMD_DDRPHY_DUMP)
110 shows the DDR PHY parameters set by the PHY training
122 - LAN (on-board SMSC9118)
124 - EEPROM (connected to the on-board I2C bus)
125 - Support card (SRAM, NOR flash, some peripherals)
131 The recommended bit switch settings are as follows:
133 SW2 OFF(1)/ON(0) Description
134 ------------------------------------------
137 bit 3 <---- SoC Bus Width 16/32
138 bit 4 <---- SERIAL_SEL[0]
139 bit 5 ----> SERIAL_SEL[1]
140 bit 6 ----> BOOTSWAP_EN
142 bit 8 <---- SOC_SERIAL_DISABLE
144 SW8 OFF(1)/ON(0) Description
145 ------------------------------------------
146 bit 1 <---- CS1_SPLIT
148 bit 3 <---- CASE10_ON
149 bit 4 Don't Care Reserve
150 bit 5 Don't Care Reserve
151 bit 6 Don't Care Reserve
153 bit 8 ----> FLASHBUS32_16
155 The BKSZ[1:0] specifies the address range of memory slot and peripherals
158 BKSZ Description RAM slot Peripherals
159 --------------------------------------------------------------------
160 0b00 15MB RAM / 1MB Peri 00000000-00efffff 00f00000-00ffffff
161 0b01 31MB RAM / 1MB Peri 00000000-01efffff 01f00000-01ffffff
162 0b10 64MB RAM / 1MB Peri 00000000-03efffff 03f00000-03ffffff
163 0b11 127MB RAM / 1MB Peri 00000000-07efffff 07f00000-07ffffff
165 Set BSKZ[1:0] to 0b01 for U-Boot.
166 This mode is the most handy because EA[24] is always supported by the save pin
167 mode of the system bus. On the other hand, EA[25] is not supported for some
168 newer SoCs. Even if it is, EA[25] is not connected on most of the boards.
171 Masahiro Yamada <yamada.masahiro@socionext.com>