2 * U-boot - start.S Startup file of u-boot for BF533/BF561
4 * Copyright (c) 2005-2007 Analog Devices Inc.
6 * This file is based on head.S
7 * Copyright (c) 2003 Metrowerks/Motorola
8 * Copyright (C) 1998 D. Jeff Dionne <jeff@ryeham.ee.ryerson.ca>,
9 * Kenneth Albanowski <kjahds@kjahds.com>,
10 * The Silver Hammer Group, Ltd.
11 * (c) 1995, Dionne & Associates
12 * (c) 1995, DKG Display Tech.
14 * See file CREDITS for list of people who contributed to this
17 * This program is free software; you can redistribute it and/or
18 * modify it under the terms of the GNU General Public License as
19 * published by the Free Software Foundation; either version 2 of
20 * the License, or (at your option) any later version.
22 * This program is distributed in the hope that it will be useful,
23 * but WITHOUT ANY WARRANTY; without even the implied warranty of
24 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
25 * GNU General Public License for more details.
27 * You should have received a copy of the GNU General Public License
28 * along with this program; if not, write to the Free Software
29 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
34 * Note: A change in this file subsequently requires a change in
35 * board/$(board_name)/config.mk for a valid u-boot.bin
40 #include <linux/config.h>
42 #include <asm/blackfin.h>
44 #include <asm/mach-common/bits/core.h>
45 #include <asm/mach-common/bits/dma.h>
46 #include <asm/mach-common/bits/pll.h>
66 * As per HW reference manual DAG registers,
67 * DATA and Address resgister shall be zero'd
68 * in initialization, after a reset state
70 r1 = 0; /* Data registers zero'd */
78 p0 = 0; /* Address registers zero'd */
85 i0 = 0; /* DAG Registers zero'd */
103 * Set loop counters to zero, to make sure that
104 * hw loops are disabled.
112 /* Check soft reset status */
114 p0.l = SWRST & 0xFFFF;
118 if !cc jump no_soft_reset;
120 /* Clear Soft reset */
128 /* Clear EVT registers */
130 p0.l = (EVT0 & 0xFFFF);
134 LSETUP(4,4) lc0 = p1;
137 p0.h = hi(SICA_IWR0);
138 p0.l = lo(SICA_IWR0);
143 sp.l = (0xffb01000 & 0xFFFF);
144 sp.h = (0xffb01000 >> 16);
147 * Check if the code is in SDRAM
148 * If the code is in SDRAM, skip SDRAM initializaiton
154 if cc jump sdram_initialized;
156 /* relocate into to RAM */
169 p2.l = (CFG_MONITOR_BASE & 0xffff);
170 p2.h = (CFG_MONITOR_BASE >> 16);
173 p4.l = ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) & 0xffff);
174 p4.h = ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) >> 16);
183 r0.h = (CONFIG_STACKBASE >> 16);
184 r0.l = (CONFIG_STACKBASE & 0xFFFF);
189 * This next section keeps the processor in supervisor mode
190 * during kernel boot. Switches to user mode at end of boot.
191 * See page 3-9 of Hardware Reference manual for documentation.
194 /* To keep ourselves in the supervisor mode */
195 p0.l = (EVT15 & 0xFFFF);
196 p0.h = (EVT15 >> 16);
202 p0.l = (IMASK & 0xFFFF);
203 p0.h = (IMASK >> 16);
204 r0.l = LO(EVT_IVG15);
205 r0.h = HI(EVT_IVG15);
220 /* DMA reset code to Hi of L1 SRAM */
222 P1.H = hi(SYSMMR_BASE); /* P1 Points to the beginning of SYSTEM MMR Space */
223 P1.L = lo(SYSMMR_BASE);
225 R0.H = reset_start; /* Source Address (high) */
226 R0.L = reset_start; /* Source Address (low) */
229 R2 = R1 - R0; /* Count */
230 R1.H = hi(L1_INST_SRAM); /* Destination Address (high) */
231 R1.L = lo(L1_INST_SRAM); /* Destination Address (low) */
232 R3.L = DMAEN; /* Source DMAConfig Value (8-bit words) */
233 R4.L = (DI_EN | WNR | DMAEN); /* Destination DMAConfig Value (8-bit words) */
237 W[P1+OFFSET_(IMDMA_S0_X_MODIFY)] = R6; /* Source Modify = 1 */
238 W[P1+OFFSET_(IMDMA_D0_X_MODIFY)] = R6; /* Destination Modify = 1 */
240 [P1+OFFSET_(IMDMA_S0_START_ADDR)] = R0; /* Set Source Base Address */
241 W[P1+OFFSET_(IMDMA_S0_X_COUNT)] = R2; /* Set Source Count */
242 /* Set Source DMAConfig = DMA Enable,
243 Memory Read, 8-Bit Transfers, 1-D DMA, Flow - Stop */
244 W[P1+OFFSET_(IMDMA_S0_CONFIG)] = R3;
246 [P1+OFFSET_(IMDMA_D0_START_ADDR)] = R1; /* Set Destination Base Address */
247 W[P1+OFFSET_(IMDMA_D0_X_COUNT)] = R2; /* Set Destination Count */
248 /* Set Destination DMAConfig = DMA Enable,
249 Memory Write, 8-Bit Transfers, 1-D DMA, Flow - Stop, IOC */
250 W[P1+OFFSET_(IMDMA_D0_CONFIG)] = R4;
253 p0.h = hi(IMDMA_D0_IRQ_STATUS);
254 p0.l = lo(IMDMA_D0_IRQ_STATUS);
257 if ! CC jump WAIT_DMA_DONE
260 W[P1+OFFSET_(IMDMA_D0_IRQ_STATUS)] = R0; /* Write 1 to clear DMA interrupt */
262 /* Initialize BSS Section with 0 s */
272 lsetup (_clear_bss, _clear_bss_end ) lc1 = p3;
274 if CC jump _clear_bss_skip;
286 p0.h = WDOG_CNT >> 16;
287 p0.l = WDOG_CNT & 0xffff;
290 p0.h = WDOG_CTL >> 16;
291 p0.l = WDOG_CTL & 0xffff;