arm: highbank: Add devicetree files
[platform/kernel/u-boot.git] / configs / mx53loco_defconfig
1 CONFIG_ARM=y
2 CONFIG_ARCH_MX5=y
3 CONFIG_SYS_TEXT_BASE=0x77800000
4 CONFIG_SYS_MALLOC_LEN=0xa00000
5 CONFIG_SYS_MALLOC_F_LEN=0x8000
6 CONFIG_NR_DRAM_BANKS=2
7 CONFIG_ENV_SIZE=0x2000
8 CONFIG_ENV_OFFSET=0xC0000
9 CONFIG_TARGET_MX53LOCO=y
10 CONFIG_SYS_I2C_MXC_I2C1=y
11 CONFIG_SYS_I2C_MXC_I2C2=y
12 CONFIG_SYS_I2C_MXC_I2C3=y
13 CONFIG_DM_GPIO=y
14 CONFIG_DEFAULT_DEVICE_TREE="imx53-qsb"
15 # CONFIG_CMD_BMODE is not set
16 CONFIG_SYS_LOAD_ADDR=0x72000000
17 CONFIG_SUPPORT_RAW_INITRD=y
18 CONFIG_USE_BOOTCOMMAND=y
19 CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else run netboot; fi"
20 CONFIG_USE_PREBOOT=y
21 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
22 CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
23 CONFIG_HUSH_PARSER=y
24 CONFIG_CMD_BOOTZ=y
25 CONFIG_CMD_DM=y
26 CONFIG_CMD_MMC=y
27 # CONFIG_CMD_PINMUX is not set
28 CONFIG_CMD_USB=y
29 # CONFIG_CMD_SETEXPR is not set
30 CONFIG_CMD_DHCP=y
31 CONFIG_CMD_MII=y
32 CONFIG_CMD_PING=y
33 CONFIG_CMD_EXT2=y
34 CONFIG_CMD_FAT=y
35 CONFIG_CMD_FS_GENERIC=y
36 CONFIG_OF_CONTROL=y
37 CONFIG_ENV_OVERWRITE=y
38 CONFIG_ENV_IS_IN_MMC=y
39 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
40 CONFIG_DM=y
41 CONFIG_SYS_I2C_LEGACY=y
42 CONFIG_SYS_I2C_MXC=y
43 CONFIG_FSL_ESDHC_IMX=y
44 CONFIG_MTD=y
45 CONFIG_PHYLIB=y
46 CONFIG_PHY_SMSC=y
47 CONFIG_PHY_FIXED=y
48 CONFIG_DM_ETH=y
49 CONFIG_FEC_MXC=y
50 CONFIG_MII=y
51 CONFIG_PINCTRL=y
52 CONFIG_PINCTRL_IMX5=y
53 CONFIG_POWER_LEGACY=y
54 CONFIG_DM_REGULATOR=y
55 CONFIG_DM_REGULATOR_FIXED=y
56 CONFIG_DM_REGULATOR_GPIO=y
57 CONFIG_POWER_I2C=y
58 CONFIG_MXC_UART=y
59 CONFIG_USB=y
60 CONFIG_USB_EHCI_MX5=y
61 CONFIG_USB_STORAGE=y
62 CONFIG_USB_HOST_ETHER=y
63 CONFIG_USB_ETHER_ASIX=y
64 CONFIG_USB_ETHER_MCS7830=y
65 CONFIG_USB_ETHER_SMSC95XX=y
66 CONFIG_SYS_WHITE_ON_BLACK=y
67 CONFIG_SPLASH_SCREEN=y