2 CONFIG_TARGET_LS1046AQDS=y
3 CONFIG_SYS_TEXT_BASE=0x82000000
4 CONFIG_SPL_LIBCOMMON_SUPPORT=y
5 CONFIG_SPL_LIBGENERIC_SUPPORT=y
7 CONFIG_SYS_MEMTEST_START=0x80000000
8 CONFIG_SYS_MEMTEST_END=0x9fffffff
10 CONFIG_ENV_OFFSET=0x300000
11 CONFIG_SYS_I2C_MXC_I2C1=y
12 CONFIG_SYS_I2C_MXC_I2C2=y
13 CONFIG_SYS_I2C_MXC_I2C3=y
14 CONFIG_SYS_I2C_MXC_I2C4=y
15 CONFIG_SYS_MALLOC_LEN=0x102000
17 CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-qds-duart"
18 CONFIG_SPL_TEXT_BASE=0x10000000
19 CONFIG_FSL_USE_PCA9547_MUX=y
23 CONFIG_SPL_DRIVERS_MISC=y
26 CONFIG_DISTRO_DEFAULTS=y
28 CONFIG_OF_BOARD_SETUP=y
29 CONFIG_SYS_EXTRA_OPTIONS="SD_BOOT_QSPI"
31 CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1046aqds/ls1046aqds_pbi.cfg"
32 CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg"
36 CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=1550000.spi-0:2m(uboot),14m(free)"
37 # CONFIG_USE_BOOTCOMMAND is not set
40 CONFIG_SPL_BOARD_INIT=y
41 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
42 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x110
43 CONFIG_SPL_ENV_SUPPORT=y
45 CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
49 CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
60 CONFIG_MTDPARTS_DEFAULT="mtdparts=1550000.spi-0:2m(uboot),14m(free)"
61 # CONFIG_SPL_EFI_PARTITION is not set
63 CONFIG_ENV_OVERWRITE=y
64 CONFIG_ENV_IS_IN_MMC=y
65 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
69 CONFIG_DYNAMIC_DDR_CLK_FREQ=y
71 CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
73 CONFIG_SYS_I2C_EARLY_INIT=y
74 CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
75 CONFIG_SYS_I2C_EEPROM_ADDR=0x57
77 # CONFIG_SPI_FLASH_BAR is not set
78 CONFIG_SPI_FLASH_SPANSION=y
79 # CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
88 CONFIG_DM_PCI_COMPAT=y
89 CONFIG_PCIE_LAYERSCAPE_RC=y
90 CONFIG_PCIE_LAYERSCAPE_EP=y
91 CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
100 CONFIG_USB_XHCI_DWC3=y
101 CONFIG_EFI_LOADER_BOUNCE_BUFFER=y