Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot...
[platform/kernel/u-boot.git] / configs / ls1043ardb_sdcard_SECURE_BOOT_defconfig
1 CONFIG_ARM=y
2 CONFIG_COUNTER_FREQUENCY=25000000
3 CONFIG_TARGET_LS1043ARDB=y
4 CONFIG_SYS_TEXT_BASE=0x82000000
5 CONFIG_SYS_MALLOC_LEN=0x102000
6 CONFIG_SPL_LIBCOMMON_SUPPORT=y
7 CONFIG_SPL_LIBGENERIC_SUPPORT=y
8 CONFIG_NR_DRAM_BANKS=2
9 CONFIG_ENV_SIZE=0x2000
10 CONFIG_NXP_ESBC=y
11 CONFIG_DM_GPIO=y
12 CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb"
13 CONFIG_SPL_TEXT_BASE=0x10000000
14 CONFIG_FSL_LS_PPA=y
15 CONFIG_SPL_MMC=y
16 CONFIG_SPL_SERIAL=y
17 CONFIG_SPL_DRIVERS_MISC=y
18 CONFIG_SPL=y
19 CONFIG_DISTRO_DEFAULTS=y
20 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
21 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0
22 CONFIG_REMAKE_ELF=y
23 CONFIG_MP=y
24 CONFIG_FIT_VERBOSE=y
25 CONFIG_OF_BOARD_SETUP=y
26 CONFIG_RAMBOOT_PBL=y
27 CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043ardb/ls1043ardb_pbi.cfg"
28 CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043ardb/ls1043ardb_rcw_sd.cfg"
29 CONFIG_SD_BOOT=y
30 CONFIG_BOOTDELAY=10
31 CONFIG_USE_BOOTARGS=y
32 CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
33 CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;"
34 CONFIG_MISC_INIT_R=y
35 CONFIG_SPL_MAX_SIZE=0x17000
36 CONFIG_SPL_PAD_TO=0x1d000
37 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
38 CONFIG_SPL_BSS_START_ADDR=0x8f000000
39 CONFIG_SPL_BSS_MAX_SIZE=0x80000
40 CONFIG_SPL_FSL_PBL=y
41 # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
42 CONFIG_SPL_STACK=0x1001e000
43 CONFIG_SYS_SPL_MALLOC=y
44 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
45 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x110
46 CONFIG_SPL_ENV_SUPPORT=y
47 CONFIG_SPL_MPC8XXX_INIT_DDR=y
48 CONFIG_SPL_WATCHDOG=y
49 CONFIG_SYS_MAXARGS=64
50 CONFIG_SYS_PBSIZE=532
51 CONFIG_CMD_IMLS=y
52 CONFIG_CMD_SPL=y
53 CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
54 CONFIG_CMD_DM=y
55 CONFIG_CMD_GPIO=y
56 CONFIG_CMD_GPT=y
57 CONFIG_CMD_I2C=y
58 CONFIG_CMD_MMC=y
59 CONFIG_CMD_NAND=y
60 CONFIG_CMD_USB=y
61 CONFIG_CMD_CACHE=y
62 CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
63 # CONFIG_SPL_EFI_PARTITION is not set
64 CONFIG_OF_CONTROL=y
65 CONFIG_SPL_OF_CONTROL=y
66 CONFIG_ENV_OVERWRITE=y
67 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
68 CONFIG_USE_ETHPRIME=y
69 CONFIG_ETHPRIME="FM1@DTSEC3"
70 CONFIG_DM=y
71 CONFIG_SPL_DM=y
72 # CONFIG_SPL_BLK is not set
73 CONFIG_MPC8XXX_GPIO=y
74 CONFIG_DM_I2C=y
75 CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
76 CONFIG_SYS_I2C_EEPROM_ADDR=0x53
77 # CONFIG_SPL_DM_MMC is not set
78 CONFIG_FSL_ESDHC=y
79 CONFIG_MTD=y
80 CONFIG_MTD_NOR_FLASH=y
81 CONFIG_FLASH_CFI_DRIVER=y
82 CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y
83 CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
84 CONFIG_SYS_FLASH_CFI=y
85 CONFIG_MTD_RAW_NAND=y
86 CONFIG_NAND_FSL_IFC=y
87 CONFIG_SYS_NAND_ONFI_DETECTION=y
88 CONFIG_SF_DEFAULT_BUS=1
89 CONFIG_SPI_FLASH_EON=y
90 CONFIG_SPI_FLASH_STMICRO=y
91 CONFIG_SPI_FLASH_SST=y
92 CONFIG_PHYLIB=y
93 CONFIG_PHY_REALTEK=y
94 CONFIG_PHY_VITESSE=y
95 CONFIG_DM_ETH=y
96 CONFIG_DM_MDIO=y
97 CONFIG_PHY_GIGE=y
98 CONFIG_E1000=y
99 CONFIG_FMAN_ENET=y
100 CONFIG_SYS_FMAN_FW_ADDR=0x900000
101 CONFIG_PCI=y
102 CONFIG_PCIE_LAYERSCAPE_RC=y
103 CONFIG_SYS_QE_FW_ADDR=0x940000
104 CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
105 CONFIG_SYS_NS16550=y
106 CONFIG_SPI=y
107 CONFIG_DM_SPI=y
108 CONFIG_USB=y
109 CONFIG_USB_XHCI_HCD=y
110 CONFIG_USB_XHCI_DWC3=y
111 # CONFIG_SPL_USE_TINY_PRINTF is not set
112 CONFIG_RSA=y
113 CONFIG_SPL_RSA=y
114 CONFIG_EFI_LOADER_BOUNCE_BUFFER=y