2 * (C) Copyright 2000-2002
3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 * See file CREDITS for list of people who contributed to this
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 of
11 * the License, or (at your option) any later version.
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
33 #include <asm/byteorder.h>
34 #if defined(CONFIG_IDE_8xx_DIRECT) || defined(CONFIG_IDE_PCMCIA)
42 #ifdef CONFIG_STATUS_LED
43 # include <status_led.h>
48 /* Macros depend on this variable */
49 static unsigned long mips_io_port_base = 0;
53 #ifdef CONFIG_SHOW_BOOT_PROGRESS
54 # include <status_led.h>
55 # define SHOW_BOOT_PROGRESS(arg) show_boot_progress(arg)
57 # define SHOW_BOOT_PROGRESS(arg)
65 #define PRINTF(fmt,args...) printf (fmt ,##args)
67 #define PRINTF(fmt,args...)
70 #if (CONFIG_COMMANDS & CFG_CMD_IDE)
72 #ifdef CONFIG_IDE_8xx_DIRECT
73 /* Timings for IDE Interface
75 * SETUP / LENGTH / HOLD - cycles valid for 50 MHz clk
76 * 70 165 30 PIO-Mode 0, [ns]
78 * 50 125 20 PIO-Mode 1, [ns]
80 * 30 100 15 PIO-Mode 2, [ns]
82 * 30 80 10 PIO-Mode 3, [ns]
84 * 25 70 10 PIO-Mode 4, [ns]
88 const static pio_config_t pio_config_ns [IDE_MAX_PIO_MODE+1] =
90 /* Setup Length Hold */
91 { 70, 165, 30 }, /* PIO-Mode 0, [ns] */
92 { 50, 125, 20 }, /* PIO-Mode 1, [ns] */
93 { 30, 101, 15 }, /* PIO-Mode 2, [ns] */
94 { 30, 80, 10 }, /* PIO-Mode 3, [ns] */
95 { 25, 70, 10 }, /* PIO-Mode 4, [ns] */
98 static pio_config_t pio_config_clk [IDE_MAX_PIO_MODE+1];
101 #define CFG_PIO_MODE 0 /* use a relaxed default */
103 static int pio_mode = CFG_PIO_MODE;
105 /* Make clock cycles and always round up */
107 #define PCMCIA_MK_CLKS( t, T ) (( (t) * (T) + 999U ) / 1000U )
109 #endif /* CONFIG_IDE_8xx_DIRECT */
111 /* ------------------------------------------------------------------------- */
113 /* Current I/O Device */
114 static int curr_device = -1;
116 /* Current offset for IDE0 / IDE1 bus access */
117 ulong ide_bus_offset[CFG_IDE_MAXBUS] = {
118 #if defined(CFG_ATA_IDE0_OFFSET)
121 #if defined(CFG_ATA_IDE1_OFFSET) && (CFG_IDE_MAXBUS > 1)
127 #define ATA_CURR_BASE(dev) (CFG_ATA_BASE_ADDR+ide_bus_offset[IDE_BUS(dev)])
129 #ifndef CONFIG_AMIGAONEG3SE
130 static int ide_bus_ok[CFG_IDE_MAXBUS];
132 static int ide_bus_ok[CFG_IDE_MAXBUS] = {0,};
135 static block_dev_desc_t ide_dev_desc[CFG_IDE_MAXDEVICE];
136 /* ------------------------------------------------------------------------- */
138 #ifdef CONFIG_IDE_LED
140 static void ide_led (uchar led, uchar status);
142 extern void ide_led (uchar led, uchar status);
145 #ifndef CONFIG_AMIGAONEG3SE
146 #define ide_led(a,b) /* dummy */
148 extern void ide_led(uchar led, uchar status);
151 #define CONFIG_IDE_LED 1
152 #define DEVICE_LED(x) 1
156 #ifdef CONFIG_IDE_RESET
157 static void ide_reset (void);
159 #define ide_reset() /* dummy */
162 static void ide_ident (block_dev_desc_t *dev_desc);
163 static uchar ide_wait (int dev, ulong t);
165 #define IDE_TIME_OUT 2000 /* 2 sec timeout */
167 #define ATAPI_TIME_OUT 7000 /* 7 sec timeout (5 sec seems to work...) */
169 #define IDE_SPIN_UP_TIME_OUT 5000 /* 5 sec spin-up timeout */
171 static void __inline__ ide_outb(int dev, int port, unsigned char val);
172 static unsigned char __inline__ ide_inb(int dev, int port);
173 static void input_data(int dev, ulong *sect_buf, int words);
174 static void output_data(int dev, ulong *sect_buf, int words);
175 static void ident_cpy (unsigned char *dest, unsigned char *src, unsigned int len);
179 static void atapi_inquiry(block_dev_desc_t *dev_desc);
180 ulong atapi_read (int device, ulong blknr, ulong blkcnt, ulong *buffer);
184 #ifdef CONFIG_IDE_8xx_DIRECT
185 static void set_pcmcia_timing (int pmode);
188 /* ------------------------------------------------------------------------- */
190 int do_ide (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
197 printf ("Usage:\n%s\n", cmdtp->usage);
200 if (strncmp(argv[1],"res",3) == 0) {
202 #ifdef CONFIG_IDE_8xx_DIRECT
203 " on PCMCIA " PCMCIA_SLOT_MSG
209 } else if (strncmp(argv[1],"inf",3) == 0) {
214 for (i=0; i<CFG_IDE_MAXDEVICE; ++i) {
215 if (ide_dev_desc[i].type==DEV_TYPE_UNKNOWN)
216 continue; /* list only known devices */
217 printf ("IDE device %d: ", i);
218 dev_print(&ide_dev_desc[i]);
222 } else if (strncmp(argv[1],"dev",3) == 0) {
223 if ((curr_device < 0) || (curr_device >= CFG_IDE_MAXDEVICE)) {
224 puts ("\nno IDE devices available\n");
227 printf ("\nIDE device %d: ", curr_device);
228 dev_print(&ide_dev_desc[curr_device]);
230 } else if (strncmp(argv[1],"part",4) == 0) {
233 for (ok=0, dev=0; dev<CFG_IDE_MAXDEVICE; ++dev) {
234 if (ide_dev_desc[dev].part_type!=PART_TYPE_UNKNOWN) {
238 print_part(&ide_dev_desc[dev]);
242 puts ("\nno IDE devices available\n");
247 printf ("Usage:\n%s\n", cmdtp->usage);
250 if (strncmp(argv[1],"dev",3) == 0) {
251 int dev = (int)simple_strtoul(argv[2], NULL, 10);
253 printf ("\nIDE device %d: ", dev);
254 if (dev >= CFG_IDE_MAXDEVICE) {
255 puts ("unknown device\n");
258 dev_print(&ide_dev_desc[dev]);
261 if (ide_dev_desc[dev].type == DEV_TYPE_UNKNOWN) {
267 puts ("... is now current device\n");
270 } else if (strncmp(argv[1],"part",4) == 0) {
271 int dev = (int)simple_strtoul(argv[2], NULL, 10);
273 if (ide_dev_desc[dev].part_type!=PART_TYPE_UNKNOWN) {
274 print_part(&ide_dev_desc[dev]);
276 printf ("\nIDE device %d not available\n", dev);
281 } else if (strncmp(argv[1],"pio",4) == 0) {
282 int mode = (int)simple_strtoul(argv[2], NULL, 10);
284 if ((mode >= 0) && (mode <= IDE_MAX_PIO_MODE)) {
289 printf ("\nInvalid PIO mode %d (0 ... %d only)\n",
290 mode, IDE_MAX_PIO_MODE);
296 printf ("Usage:\n%s\n", cmdtp->usage);
299 /* at least 4 args */
301 if (strcmp(argv[1],"read") == 0) {
302 ulong addr = simple_strtoul(argv[2], NULL, 16);
303 ulong blk = simple_strtoul(argv[3], NULL, 16);
304 ulong cnt = simple_strtoul(argv[4], NULL, 16);
307 printf ("\nIDE read: device %d block # %ld, count %ld ... ",
308 curr_device, blk, cnt);
310 n = ide_dev_desc[curr_device].block_read (curr_device,
313 /* flush cache after read */
314 flush_cache (addr, cnt*ide_dev_desc[curr_device].blksz);
316 printf ("%ld blocks read: %s\n",
317 n, (n==cnt) ? "OK" : "ERROR");
323 } else if (strcmp(argv[1],"write") == 0) {
324 ulong addr = simple_strtoul(argv[2], NULL, 16);
325 ulong blk = simple_strtoul(argv[3], NULL, 16);
326 ulong cnt = simple_strtoul(argv[4], NULL, 16);
329 printf ("\nIDE write: device %d block # %ld, count %ld ... ",
330 curr_device, blk, cnt);
332 n = ide_write (curr_device, blk, cnt, (ulong *)addr);
334 printf ("%ld blocks written: %s\n",
335 n, (n==cnt) ? "OK" : "ERROR");
342 printf ("Usage:\n%s\n", cmdtp->usage);
350 int do_diskboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
352 char *boot_device = NULL;
357 disk_partition_t info;
363 addr = CFG_LOAD_ADDR;
364 boot_device = getenv ("bootdevice");
367 addr = simple_strtoul(argv[1], NULL, 16);
368 boot_device = getenv ("bootdevice");
371 addr = simple_strtoul(argv[1], NULL, 16);
372 boot_device = argv[2];
375 printf ("Usage:\n%s\n", cmdtp->usage);
376 SHOW_BOOT_PROGRESS (-1);
381 puts ("\n** No boot device **\n");
382 SHOW_BOOT_PROGRESS (-1);
386 dev = simple_strtoul(boot_device, &ep, 16);
388 if (ide_dev_desc[dev].type==DEV_TYPE_UNKNOWN) {
389 printf ("\n** Device %d not available\n", dev);
390 SHOW_BOOT_PROGRESS (-1);
396 puts ("\n** Invalid boot device, use `dev[:part]' **\n");
397 SHOW_BOOT_PROGRESS (-1);
400 part = simple_strtoul(++ep, NULL, 16);
402 if (get_partition_info (&ide_dev_desc[dev], part, &info)) {
403 SHOW_BOOT_PROGRESS (-1);
406 if ((strncmp(info.type, BOOT_PART_TYPE, sizeof(info.type)) != 0) &&
407 (strncmp(info.type, BOOT_PART_COMP, sizeof(info.type)) != 0)) {
408 printf ("\n** Invalid partition type \"%.32s\""
409 " (expect \"" BOOT_PART_TYPE "\")\n",
411 SHOW_BOOT_PROGRESS (-1);
415 printf ("\nLoading from IDE device %d, partition %d: "
416 "Name: %.32s Type: %.32s\n",
417 dev, part, info.name, info.type);
419 PRINTF ("First Block: %ld, # of blocks: %ld, Block Size: %ld\n",
420 info.start, info.size, info.blksz);
422 if (ide_dev_desc[dev].block_read (dev, info.start, 1, (ulong *)addr) != 1) {
423 printf ("** Read error on %d:%d\n", dev, part);
424 SHOW_BOOT_PROGRESS (-1);
428 hdr = (image_header_t *)addr;
430 if (ntohl(hdr->ih_magic) == IH_MAGIC) {
432 print_image_hdr (hdr);
434 cnt = (ntohl(hdr->ih_size) + sizeof(image_header_t));
435 cnt += info.blksz - 1;
439 printf("\n** Bad Magic Number **\n");
440 SHOW_BOOT_PROGRESS (-1);
444 if (ide_dev_desc[dev].block_read (dev, info.start+1, cnt,
445 (ulong *)(addr+info.blksz)) != cnt) {
446 printf ("** Read error on %d:%d\n", dev, part);
447 SHOW_BOOT_PROGRESS (-1);
452 /* Loading ok, update default load address */
456 /* Check if we should attempt an auto-start */
457 if (((ep = getenv("autostart")) != NULL) && (strcmp(ep,"yes") == 0)) {
459 extern int do_bootm (cmd_tbl_t *, int, int, char *[]);
461 local_args[0] = argv[0];
462 local_args[1] = NULL;
464 printf ("Automatic boot of image at addr 0x%08lX ...\n", addr);
466 do_bootm (cmdtp, 0, 1, local_args);
472 /* ------------------------------------------------------------------------- */
477 #ifdef CONFIG_IDE_8xx_DIRECT
478 DECLARE_GLOBAL_DATA_PTR;
479 volatile immap_t *immr = (immap_t *)CFG_IMMR;
480 volatile pcmconf8xx_t *pcmp = &(immr->im_pcmcia);
484 #ifdef CONFIG_AMIGAONEG3SE
485 unsigned int max_bus_scan;
486 unsigned int ata_reset_time;
490 #ifdef CONFIG_IDE_8xx_PCCARD
491 extern int pcmcia_on (void);
492 extern int ide_devices_found; /* Initialized in check_ide_device() */
496 ide_devices_found = 0;
497 /* initialize the PCMCIA IDE adapter card */
499 if (!ide_devices_found)
501 udelay (1000000); /* 1 s */
502 #endif /* CONFIG_IDE_8xx_PCCARD */
506 #ifdef CONFIG_IDE_8xx_DIRECT
507 /* Initialize PIO timing tables */
508 for (i=0; i <= IDE_MAX_PIO_MODE; ++i) {
509 pio_config_clk[i].t_setup = PCMCIA_MK_CLKS(pio_config_ns[i].t_setup,
511 pio_config_clk[i].t_length = PCMCIA_MK_CLKS(pio_config_ns[i].t_length,
513 pio_config_clk[i].t_hold = PCMCIA_MK_CLKS(pio_config_ns[i].t_hold,
515 PRINTF ("PIO Mode %d: setup=%2d ns/%d clk"
517 " hold=%2d ns/%d clk\n",
519 pio_config_ns[i].t_setup, pio_config_clk[i].t_setup,
520 pio_config_ns[i].t_length, pio_config_clk[i].t_length,
521 pio_config_ns[i].t_hold, pio_config_clk[i].t_hold);
523 #endif /* CONFIG_IDE_8xx_DIRECT */
525 /* Reset the IDE just to be sure.
526 * Light LED's to show
528 ide_led ((LED_IDE1 | LED_IDE2), 1); /* LED's on */
529 ide_reset (); /* ATAPI Drives seems to need a proper IDE Reset */
531 #ifdef CONFIG_IDE_8xx_DIRECT
532 /* PCMCIA / IDE initialization for common mem space */
533 pcmp->pcmc_pgcrb = 0;
535 /* start in PIO mode 0 - most relaxed timings */
537 set_pcmcia_timing (pio_mode);
538 #endif /* CONFIG_IDE_8xx_DIRECT */
541 * Wait for IDE to get ready.
542 * According to spec, this can take up to 31 seconds!
544 #ifndef CONFIG_AMIGAONEG3SE
545 for (bus=0; bus<CFG_IDE_MAXBUS; ++bus) {
546 int dev = bus * (CFG_IDE_MAXDEVICE / CFG_IDE_MAXBUS);
548 s = getenv("ide_maxbus");
550 max_bus_scan = simple_strtol(s, NULL, 10);
552 max_bus_scan = CFG_IDE_MAXBUS;
554 for (bus=0; bus<max_bus_scan; ++bus) {
555 int dev = bus * (CFG_IDE_MAXDEVICE / max_bus_scan);
558 #ifdef CONFIG_IDE_8xx_PCCARD
559 /* Skip non-ide devices from probing */
560 if ((ide_devices_found & (1 << bus)) == 0) {
561 ide_led ((LED_IDE1 | LED_IDE2), 0); /* LED's off */
565 printf ("Bus %d: ", bus);
571 udelay (100000); /* 100 ms */
572 ide_outb (dev, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(dev));
573 udelay (100000); /* 100 ms */
574 #ifdef CONFIG_AMIGAONEG3SE
575 ata_reset_time = ATA_RESET_TIME;
576 s = getenv("ide_reset_timeout");
577 if (s) ata_reset_time = 2*simple_strtol(s, NULL, 10);
581 udelay (10000); /* 10 ms */
583 c = ide_inb (dev, ATA_STATUS);
585 #ifdef CONFIG_AMIGAONEG3SE
586 if (i > (ata_reset_time * 100)) {
588 if (i > (ATA_RESET_TIME * 100)) {
590 puts ("** Timeout **\n");
591 ide_led ((LED_IDE1 | LED_IDE2), 0); /* LED's off */
592 #ifdef CONFIG_AMIGAONEG3SE
593 /* If this is the second bus, the first one was OK */
602 if ((i >= 100) && ((i%100)==0)) {
605 } while (c & ATA_STAT_BUSY);
607 if (c & (ATA_STAT_BUSY | ATA_STAT_FAULT)) {
608 puts ("not available ");
609 PRINTF ("Status = 0x%02X ", c);
610 #ifndef CONFIG_ATAPI /* ATAPI Devices do not set DRDY */
611 } else if ((c & ATA_STAT_READY) == 0) {
612 puts ("not available ");
613 PRINTF ("Status = 0x%02X ", c);
622 #ifdef CONFIG_AMIGAONEG3SE
627 ide_led ((LED_IDE1 | LED_IDE2), 0); /* LED's off */
630 for (i=0; i<CFG_IDE_MAXDEVICE; ++i) {
631 #ifdef CONFIG_IDE_LED
632 int led = (IDE_BUS(i) == 0) ? LED_IDE1 : LED_IDE2;
634 ide_dev_desc[i].if_type=IF_TYPE_IDE;
635 ide_dev_desc[i].dev=i;
636 ide_dev_desc[i].part_type=PART_TYPE_UNKNOWN;
637 ide_dev_desc[i].blksz=0;
638 ide_dev_desc[i].lba=0;
639 ide_dev_desc[i].block_read=ide_read;
640 if (!ide_bus_ok[IDE_BUS(i)])
642 ide_led (led, 1); /* LED on */
643 ide_ident(&ide_dev_desc[i]);
644 ide_led (led, 0); /* LED off */
645 dev_print(&ide_dev_desc[i]);
647 if ((ide_dev_desc[i].lba > 0) && (ide_dev_desc[i].blksz > 0)) {
648 init_part (&ide_dev_desc[i]); /* initialize partition type */
656 /* ------------------------------------------------------------------------- */
658 block_dev_desc_t * ide_get_dev(int dev)
660 return ((block_dev_desc_t *)&ide_dev_desc[dev]);
664 #ifdef CONFIG_IDE_8xx_DIRECT
667 set_pcmcia_timing (int pmode)
669 volatile immap_t *immr = (immap_t *)CFG_IMMR;
670 volatile pcmconf8xx_t *pcmp = &(immr->im_pcmcia);
673 PRINTF ("Set timing for PIO Mode %d\n", pmode);
675 timings = PCMCIA_SHT(pio_config_clk[pmode].t_hold)
676 | PCMCIA_SST(pio_config_clk[pmode].t_setup)
677 | PCMCIA_SL (pio_config_clk[pmode].t_length)
682 pcmp->pcmc_pbr0 = CFG_PCMCIA_PBR0;
683 pcmp->pcmc_por0 = CFG_PCMCIA_POR0
684 #if (CFG_PCMCIA_POR0 != 0)
688 PRINTF ("PBR0: %08x POR0: %08x\n", pcmp->pcmc_pbr0, pcmp->pcmc_por0);
690 pcmp->pcmc_pbr1 = CFG_PCMCIA_PBR1;
691 pcmp->pcmc_por1 = CFG_PCMCIA_POR1
692 #if (CFG_PCMCIA_POR1 != 0)
696 PRINTF ("PBR1: %08x POR1: %08x\n", pcmp->pcmc_pbr1, pcmp->pcmc_por1);
698 pcmp->pcmc_pbr2 = CFG_PCMCIA_PBR2;
699 pcmp->pcmc_por2 = CFG_PCMCIA_POR2
700 #if (CFG_PCMCIA_POR2 != 0)
704 PRINTF ("PBR2: %08x POR2: %08x\n", pcmp->pcmc_pbr2, pcmp->pcmc_por2);
706 pcmp->pcmc_pbr3 = CFG_PCMCIA_PBR3;
707 pcmp->pcmc_por3 = CFG_PCMCIA_POR3
708 #if (CFG_PCMCIA_POR3 != 0)
712 PRINTF ("PBR3: %08x POR3: %08x\n", pcmp->pcmc_pbr3, pcmp->pcmc_por3);
716 pcmp->pcmc_pbr4 = CFG_PCMCIA_PBR4;
717 pcmp->pcmc_por4 = CFG_PCMCIA_POR4
718 #if (CFG_PCMCIA_POR4 != 0)
722 PRINTF ("PBR4: %08x POR4: %08x\n", pcmp->pcmc_pbr4, pcmp->pcmc_por4);
724 pcmp->pcmc_pbr5 = CFG_PCMCIA_PBR5;
725 pcmp->pcmc_por5 = CFG_PCMCIA_POR5
726 #if (CFG_PCMCIA_POR5 != 0)
730 PRINTF ("PBR5: %08x POR5: %08x\n", pcmp->pcmc_pbr5, pcmp->pcmc_por5);
732 pcmp->pcmc_pbr6 = CFG_PCMCIA_PBR6;
733 pcmp->pcmc_por6 = CFG_PCMCIA_POR6
734 #if (CFG_PCMCIA_POR6 != 0)
738 PRINTF ("PBR6: %08x POR6: %08x\n", pcmp->pcmc_pbr6, pcmp->pcmc_por6);
740 pcmp->pcmc_pbr7 = CFG_PCMCIA_PBR7;
741 pcmp->pcmc_por7 = CFG_PCMCIA_POR7
742 #if (CFG_PCMCIA_POR7 != 0)
746 PRINTF ("PBR7: %08x POR7: %08x\n", pcmp->pcmc_pbr7, pcmp->pcmc_por7);
750 #endif /* CONFIG_IDE_8xx_DIRECT */
752 /* ------------------------------------------------------------------------- */
755 static void __inline__
756 ide_outb(int dev, int port, unsigned char val)
758 /* Ensure I/O operations complete */
759 __asm__ volatile("eieio");
760 *((uchar *)(ATA_CURR_BASE(dev)+port)) = val;
762 printf ("ide_outb: 0x%08lx <== 0x%02x\n", ATA_CURR_BASE(dev)+port, val);
765 #else /* ! __PPC__ */
766 static void __inline__
767 ide_outb(int dev, int port, unsigned char val)
769 outb(val, ATA_CURR_BASE(dev)+port);
775 static unsigned char __inline__
776 ide_inb(int dev, int port)
779 /* Ensure I/O operations complete */
780 __asm__ volatile("eieio");
781 val = *((uchar *)(ATA_CURR_BASE(dev)+port));
783 printf ("ide_inb: 0x%08lx ==> 0x%02x\n", ATA_CURR_BASE(dev)+port, val);
787 #else /* ! __PPC__ */
788 static unsigned char __inline__
789 ide_inb(int dev, int port)
791 return inb(ATA_CURR_BASE(dev)+port);
796 # ifdef CONFIG_AMIGAONEG3SE
798 output_data_short(int dev, ulong *sect_buf, int words)
801 volatile ushort *pbuf;
803 pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
804 dbuf = (ushort *)sect_buf;
806 __asm__ volatile ("eieio");
808 __asm__ volatile ("eieio");
814 # endif /* CONFIG_AMIGAONEG3SE */
817 /* We only need to swap data if we are running on a big endian cpu. */
818 /* But Au1x00 cpu:s already swaps data in big endian mode! */
819 #if defined(__LITTLE_ENDIAN) || defined(CONFIG_AU1X00)
820 #define input_swap_data(x,y,z) input_data(x,y,z)
823 input_swap_data(int dev, ulong *sect_buf, int words)
825 volatile ushort *pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
826 ushort *dbuf = (ushort *)sect_buf;
829 *dbuf++ = ld_le16(pbuf);
830 *dbuf++ = ld_le16(pbuf);
833 #endif /* __LITTLE_ENDIAN || CONFIG_AU1X00 */
838 output_data(int dev, ulong *sect_buf, int words)
841 volatile ushort *pbuf;
843 pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
844 dbuf = (ushort *)sect_buf;
846 __asm__ volatile ("eieio");
848 __asm__ volatile ("eieio");
852 #else /* ! __PPC__ */
854 output_data(int dev, ulong *sect_buf, int words)
856 outsw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words<<1);
862 input_data(int dev, ulong *sect_buf, int words)
865 volatile ushort *pbuf;
867 pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
868 dbuf = (ushort *)sect_buf;
870 __asm__ volatile ("eieio");
872 __asm__ volatile ("eieio");
876 #else /* ! __PPC__ */
878 input_data(int dev, ulong *sect_buf, int words)
880 insw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, words << 1);
885 #ifdef CONFIG_AMIGAONEG3SE
887 input_data_short(int dev, ulong *sect_buf, int words)
890 volatile ushort *pbuf;
892 pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
893 dbuf = (ushort *)sect_buf;
895 __asm__ volatile ("eieio");
897 __asm__ volatile ("eieio");
908 /* -------------------------------------------------------------------------
910 static void ide_ident (block_dev_desc_t *dev_desc)
912 ulong iobuf[ATA_SECTORWORDS];
914 hd_driveid_t *iop = (hd_driveid_t *)iobuf;
916 #ifdef CONFIG_AMIGAONEG3SE
924 int mode, cycle_time;
927 device=dev_desc->dev;
928 printf (" Device %d: ", device);
930 #ifdef CONFIG_AMIGAONEG3SE
931 s = getenv("ide_maxbus");
933 max_bus_scan = simple_strtol(s, NULL, 10);
935 max_bus_scan = CFG_IDE_MAXBUS;
937 if (device >= max_bus_scan*2) {
938 dev_desc->type=DEV_TYPE_UNKNOWN;
943 ide_led (DEVICE_LED(device), 1); /* LED on */
946 ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
947 dev_desc->if_type=IF_TYPE_IDE;
950 #ifdef CONFIG_AMIGAONEG3SE
954 /* Warning: This will be tricky to read */
957 #endif /* CONFIG_AMIGAONEG3SE */
959 /* check signature */
960 if ((ide_inb(device,ATA_SECT_CNT) == 0x01) &&
961 (ide_inb(device,ATA_SECT_NUM) == 0x01) &&
962 (ide_inb(device,ATA_CYL_LOW) == 0x14) &&
963 (ide_inb(device,ATA_CYL_HIGH) == 0xEB)) {
964 /* ATAPI Signature found */
965 dev_desc->if_type=IF_TYPE_ATAPI;
966 /* Start Ident Command
968 ide_outb (device, ATA_COMMAND, ATAPI_CMD_IDENT);
970 * Wait for completion - ATAPI devices need more time
973 c = ide_wait (device, ATAPI_TIME_OUT);
978 /* Start Ident Command
980 ide_outb (device, ATA_COMMAND, ATA_CMD_IDENT);
982 /* Wait for completion
984 c = ide_wait (device, IDE_TIME_OUT);
986 ide_led (DEVICE_LED(device), 0); /* LED off */
988 if (((c & ATA_STAT_DRQ) == 0) ||
989 ((c & (ATA_STAT_FAULT|ATA_STAT_ERR)) != 0) ) {
990 #ifdef CONFIG_AMIGAONEG3SE
994 dev_desc->type=DEV_TYPE_UNKNOWN;
998 dev_desc->type=DEV_TYPE_UNKNOWN;
1000 #endif /* CONFIG_AMIGAONEG3SE */
1003 #ifdef CONFIG_AMIGAONEG3SE
1004 s = getenv("ide_doreset");
1005 if (s && strcmp(s, "on") == 0 && 1 == do_retry) {
1006 /* Need to soft reset the device in case it's an ATAPI... */
1007 PRINTF("Retrying...\n");
1008 ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
1010 ide_outb (device, ATA_COMMAND, 0x08);
1011 udelay (100000); /* 100 ms */
1016 } /* see above - ugly to read */
1017 #endif /* CONFIG_AMIGAONEG3SE */
1019 input_swap_data (device, iobuf, ATA_SECTORWORDS);
1021 ident_cpy (dev_desc->revision, iop->fw_rev, sizeof(dev_desc->revision));
1022 ident_cpy (dev_desc->vendor, iop->model, sizeof(dev_desc->vendor));
1023 ident_cpy (dev_desc->product, iop->serial_no, sizeof(dev_desc->product));
1025 if ((iop->config & 0x0080)==0x0080)
1026 dev_desc->removable = 1;
1028 dev_desc->removable = 0;
1032 * Drive PIO mode autoselection
1036 printf ("tPIO = 0x%02x = %d\n",mode, mode);
1037 if (mode > 2) { /* 2 is maximum allowed tPIO value */
1039 PRINTF ("Override tPIO -> 2\n");
1041 if (iop->field_valid & 2) { /* drive implements ATA2? */
1042 PRINTF ("Drive implements ATA2\n");
1043 if (iop->capability & 8) { /* drive supports use_iordy? */
1044 cycle_time = iop->eide_pio_iordy;
1046 cycle_time = iop->eide_pio;
1048 PRINTF ("cycle time = %d\n", cycle_time);
1050 if (cycle_time > 120) mode = 3; /* 120 ns for PIO mode 4 */
1051 if (cycle_time > 180) mode = 2; /* 180 ns for PIO mode 3 */
1052 if (cycle_time > 240) mode = 1; /* 240 ns for PIO mode 4 */
1053 if (cycle_time > 383) mode = 0; /* 383 ns for PIO mode 4 */
1055 printf ("PIO mode to use: PIO %d\n", mode);
1059 if (dev_desc->if_type==IF_TYPE_ATAPI) {
1060 atapi_inquiry(dev_desc);
1063 #endif /* CONFIG_ATAPI */
1066 dev_desc->lba = (iop->lba_capacity << 16) | (iop->lba_capacity >> 16);
1068 dev_desc->type=DEV_TYPE_HARDDISK;
1069 dev_desc->blksz=ATA_BLOCKSIZE;
1070 dev_desc->lun=0; /* just to fill something in... */
1072 #if 0 /* only used to test the powersaving mode,
1073 * if enabled, the drive goes after 5 sec
1074 * in standby mode */
1075 ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
1076 c = ide_wait (device, IDE_TIME_OUT);
1077 ide_outb (device, ATA_SECT_CNT, 1);
1078 ide_outb (device, ATA_LBA_LOW, 0);
1079 ide_outb (device, ATA_LBA_MID, 0);
1080 ide_outb (device, ATA_LBA_HIGH, 0);
1081 ide_outb (device, ATA_DEV_HD, ATA_LBA |
1082 ATA_DEVICE(device));
1083 ide_outb (device, ATA_COMMAND, 0xe3);
1085 c = ide_wait (device, IDE_TIME_OUT); /* can't take over 500 ms */
1090 /* ------------------------------------------------------------------------- */
1092 ulong ide_read (int device, ulong blknr, ulong blkcnt, ulong *buffer)
1096 unsigned char pwrsave=0; /* power save */
1098 PRINTF ("ide_read dev %d start %lX, blocks %lX buffer at %lX\n",
1099 device, blknr, blkcnt, (ulong)buffer);
1101 ide_led (DEVICE_LED(device), 1); /* LED on */
1105 ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
1106 c = ide_wait (device, IDE_TIME_OUT);
1108 if (c & ATA_STAT_BUSY) {
1109 printf ("IDE read: device %d not ready\n", device);
1113 /* first check if the drive is in Powersaving mode, if yes,
1114 * increase the timeout value */
1115 ide_outb (device, ATA_COMMAND, ATA_CMD_CHK_PWR);
1118 c = ide_wait (device, IDE_TIME_OUT); /* can't take over 500 ms */
1120 if (c & ATA_STAT_BUSY) {
1121 printf ("IDE read: device %d not ready\n", device);
1124 if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) {
1125 printf ("No Powersaving mode %X\n", c);
1127 c = ide_inb(device,ATA_SECT_CNT);
1128 PRINTF("Powersaving %02X\n",c);
1134 while (blkcnt-- > 0) {
1136 c = ide_wait (device, IDE_TIME_OUT);
1138 if (c & ATA_STAT_BUSY) {
1139 printf ("IDE read: device %d not ready\n", device);
1143 ide_outb (device, ATA_SECT_CNT, 1);
1144 ide_outb (device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
1145 ide_outb (device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
1146 ide_outb (device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
1147 ide_outb (device, ATA_DEV_HD, ATA_LBA |
1148 ATA_DEVICE(device) |
1149 ((blknr >> 24) & 0xF) );
1150 ide_outb (device, ATA_COMMAND, ATA_CMD_READ);
1155 c = ide_wait (device, IDE_SPIN_UP_TIME_OUT); /* may take up to 4 sec */
1158 c = ide_wait (device, IDE_TIME_OUT); /* can't take over 500 ms */
1161 if ((c&(ATA_STAT_DRQ|ATA_STAT_BUSY|ATA_STAT_ERR)) != ATA_STAT_DRQ) {
1162 printf ("Error (no IRQ) dev %d blk %ld: status 0x%02x\n",
1167 input_data (device, buffer, ATA_SECTORWORDS);
1168 (void) ide_inb (device, ATA_STATUS); /* clear IRQ */
1172 buffer += ATA_SECTORWORDS;
1175 ide_led (DEVICE_LED(device), 0); /* LED off */
1179 /* ------------------------------------------------------------------------- */
1182 ulong ide_write (int device, ulong blknr, ulong blkcnt, ulong *buffer)
1187 ide_led (DEVICE_LED(device), 1); /* LED on */
1191 ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
1193 while (blkcnt-- > 0) {
1195 c = ide_wait (device, IDE_TIME_OUT);
1197 if (c & ATA_STAT_BUSY) {
1198 printf ("IDE read: device %d not ready\n", device);
1202 ide_outb (device, ATA_SECT_CNT, 1);
1203 ide_outb (device, ATA_LBA_LOW, (blknr >> 0) & 0xFF);
1204 ide_outb (device, ATA_LBA_MID, (blknr >> 8) & 0xFF);
1205 ide_outb (device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF);
1206 ide_outb (device, ATA_DEV_HD, ATA_LBA |
1207 ATA_DEVICE(device) |
1208 ((blknr >> 24) & 0xF) );
1209 ide_outb (device, ATA_COMMAND, ATA_CMD_WRITE);
1213 c = ide_wait (device, IDE_TIME_OUT); /* can't take over 500 ms */
1215 if ((c&(ATA_STAT_DRQ|ATA_STAT_BUSY|ATA_STAT_ERR)) != ATA_STAT_DRQ) {
1216 printf ("Error (no IRQ) dev %d blk %ld: status 0x%02x\n",
1221 output_data (device, buffer, ATA_SECTORWORDS);
1222 c = ide_inb (device, ATA_STATUS); /* clear IRQ */
1225 buffer += ATA_SECTORWORDS;
1228 ide_led (DEVICE_LED(device), 0); /* LED off */
1232 /* ------------------------------------------------------------------------- */
1235 * copy src to dest, skipping leading and trailing blanks and null
1236 * terminate the string
1238 static void ident_cpy (unsigned char *dest, unsigned char *src, unsigned int len)
1244 if (src[start]!=' ')
1254 for ( ; start<=end; start++) {
1260 /* ------------------------------------------------------------------------- */
1263 * Wait until Busy bit is off, or timeout (in ms)
1264 * Return last status
1266 static uchar ide_wait (int dev, ulong t)
1268 ulong delay = 10 * t; /* poll every 100 us */
1271 while ((c = ide_inb(dev, ATA_STATUS)) & ATA_STAT_BUSY) {
1280 /* ------------------------------------------------------------------------- */
1282 #ifdef CONFIG_IDE_RESET
1283 extern void ide_set_reset(int idereset);
1285 static void ide_reset (void)
1287 #if defined(CFG_PB_12V_ENABLE) || defined(CFG_PB_IDE_MOTOR)
1288 volatile immap_t *immr = (immap_t *)CFG_IMMR;
1293 for (i=0; i<CFG_IDE_MAXBUS; ++i)
1295 for (i=0; i<CFG_IDE_MAXDEVICE; ++i)
1296 ide_dev_desc[i].type = DEV_TYPE_UNKNOWN;
1298 ide_set_reset (1); /* assert reset */
1302 #ifdef CFG_PB_12V_ENABLE
1303 immr->im_cpm.cp_pbdat &= ~(CFG_PB_12V_ENABLE); /* 12V Enable output OFF */
1304 immr->im_cpm.cp_pbpar &= ~(CFG_PB_12V_ENABLE);
1305 immr->im_cpm.cp_pbodr &= ~(CFG_PB_12V_ENABLE);
1306 immr->im_cpm.cp_pbdir |= CFG_PB_12V_ENABLE;
1308 /* wait 500 ms for the voltage to stabilize
1310 for (i=0; i<500; ++i) {
1314 immr->im_cpm.cp_pbdat |= CFG_PB_12V_ENABLE; /* 12V Enable output ON */
1315 #endif /* CFG_PB_12V_ENABLE */
1317 #ifdef CFG_PB_IDE_MOTOR
1318 /* configure IDE Motor voltage monitor pin as input */
1319 immr->im_cpm.cp_pbpar &= ~(CFG_PB_IDE_MOTOR);
1320 immr->im_cpm.cp_pbodr &= ~(CFG_PB_IDE_MOTOR);
1321 immr->im_cpm.cp_pbdir &= ~(CFG_PB_IDE_MOTOR);
1323 /* wait up to 1 s for the motor voltage to stabilize
1325 for (i=0; i<1000; ++i) {
1326 if ((immr->im_cpm.cp_pbdat & CFG_PB_IDE_MOTOR) != 0) {
1332 if (i == 1000) { /* Timeout */
1333 printf ("\nWarning: 5V for IDE Motor missing\n");
1334 # ifdef CONFIG_STATUS_LED
1335 # ifdef STATUS_LED_YELLOW
1336 status_led_set (STATUS_LED_YELLOW, STATUS_LED_ON );
1338 # ifdef STATUS_LED_GREEN
1339 status_led_set (STATUS_LED_GREEN, STATUS_LED_OFF);
1341 # endif /* CONFIG_STATUS_LED */
1343 #endif /* CFG_PB_IDE_MOTOR */
1347 /* de-assert RESET signal */
1351 for (i=0; i<250; ++i) {
1356 #endif /* CONFIG_IDE_RESET */
1358 /* ------------------------------------------------------------------------- */
1360 #if defined(CONFIG_IDE_LED) && !defined(CONFIG_AMIGAONEG3SE) && !defined(CONFIG_KUP4K)
1362 static uchar led_buffer = 0; /* Buffer for current LED status */
1364 static void ide_led (uchar led, uchar status)
1366 uchar *led_port = LED_PORT;
1368 if (status) { /* switch LED on */
1370 } else { /* switch LED off */
1374 *led_port = led_buffer;
1377 #endif /* CONFIG_IDE_LED */
1379 /* ------------------------------------------------------------------------- */
1382 /****************************************************************************
1390 #define AT_PRINTF(fmt,args...) printf (fmt ,##args)
1392 #define AT_PRINTF(fmt,args...)
1396 /* since ATAPI may use commands with not 4 bytes alligned length
1397 * we have our own transfer functions, 2 bytes alligned */
1399 output_data_shorts(int dev, ushort *sect_buf, int shorts)
1402 volatile ushort *pbuf;
1404 pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
1405 dbuf = (ushort *)sect_buf;
1407 __asm__ volatile ("eieio");
1413 input_data_shorts(int dev, ushort *sect_buf, int shorts)
1416 volatile ushort *pbuf;
1418 pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
1419 dbuf = (ushort *)sect_buf;
1421 __asm__ volatile ("eieio");
1426 #else /* ! __PPC__ */
1428 output_data_shorts(int dev, ushort *sect_buf, int shorts)
1430 outsw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, shorts);
1435 input_data_shorts(int dev, ushort *sect_buf, int shorts)
1437 insw(ATA_CURR_BASE(dev)+ATA_DATA_REG, sect_buf, shorts);
1440 #endif /* __PPC__ */
1443 * Wait until (Status & mask) == res, or timeout (in ms)
1444 * Return last status
1445 * This is used since some ATAPI CD ROMs clears their Busy Bit first
1446 * and then they set their DRQ Bit
1448 static uchar atapi_wait_mask (int dev, ulong t,uchar mask, uchar res)
1450 ulong delay = 10 * t; /* poll every 100 us */
1453 c = ide_inb(dev,ATA_DEV_CTL); /* prevents to read the status before valid */
1454 while (((c = ide_inb(dev, ATA_STATUS)) & mask) != res) {
1455 /* break if error occurs (doesn't make sense to wait more) */
1456 if((c & ATA_STAT_ERR)==ATA_STAT_ERR)
1467 * issue an atapi command
1469 unsigned char atapi_issue(int device,unsigned char* ccb,int ccblen, unsigned char * buffer,int buflen)
1471 unsigned char c,err,mask,res;
1473 ide_led (DEVICE_LED(device), 1); /* LED on */
1477 mask = ATA_STAT_BUSY|ATA_STAT_DRQ;
1479 #ifdef CONFIG_AMIGAONEG3SE
1480 # warning THF: Removed LBA mode ???
1482 ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
1483 c = atapi_wait_mask(device,ATAPI_TIME_OUT,mask,res);
1484 if ((c & mask) != res) {
1485 printf ("ATAPI_ISSUE: device %d not ready status %X\n", device,c);
1489 /* write taskfile */
1490 ide_outb (device, ATA_ERROR_REG, 0); /* no DMA, no overlaped */
1491 ide_outb (device, ATA_SECT_CNT, 0);
1492 ide_outb (device, ATA_SECT_NUM, 0);
1493 ide_outb (device, ATA_CYL_LOW, (unsigned char)(buflen & 0xFF));
1494 ide_outb (device, ATA_CYL_HIGH, (unsigned char)((buflen>>8) & 0xFF));
1495 #ifdef CONFIG_AMIGAONEG3SE
1496 # warning THF: Removed LBA mode ???
1498 ide_outb (device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device));
1500 ide_outb (device, ATA_COMMAND, ATAPI_CMD_PACKET);
1503 mask = ATA_STAT_DRQ|ATA_STAT_BUSY|ATA_STAT_ERR;
1505 c = atapi_wait_mask(device,ATAPI_TIME_OUT,mask,res);
1507 if ((c & mask) != res) { /* DRQ must be 1, BSY 0 */
1508 printf ("ATTAPI_ISSUE: Error (no IRQ) before sending ccb dev %d status 0x%02x\n",device,c);
1513 output_data_shorts (device, (unsigned short *)ccb,ccblen/2); /* write command block */
1514 /* ATAPI Command written wait for completition */
1515 udelay (5000); /* device must set bsy */
1517 mask = ATA_STAT_DRQ|ATA_STAT_BUSY|ATA_STAT_ERR;
1518 /* if no data wait for DRQ = 0 BSY = 0
1519 * if data wait for DRQ = 1 BSY = 0 */
1523 c = atapi_wait_mask(device,ATAPI_TIME_OUT,mask,res);
1524 if ((c & mask) != res ) {
1525 if (c & ATA_STAT_ERR) {
1526 err=(ide_inb(device,ATA_ERROR_REG))>>4;
1527 AT_PRINTF("atapi_issue 1 returned sense key %X status %02X\n",err,c);
1529 printf ("ATTAPI_ISSUE: (no DRQ) after sending ccb (%x) status 0x%02x\n", ccb[0],c);
1534 n=ide_inb(device, ATA_CYL_HIGH);
1536 n+=ide_inb(device, ATA_CYL_LOW);
1538 printf("ERROR, transfer bytes %d requested only %d\n",n,buflen);
1542 if((n==0)&&(buflen<0)) {
1543 printf("ERROR, transfer bytes %d requested %d\n",n,buflen);
1548 AT_PRINTF("WARNING, transfer bytes %d not equal with requested %d\n",n,buflen);
1550 if(n!=0) { /* data transfer */
1551 AT_PRINTF("ATAPI_ISSUE: %d Bytes to transfer\n",n);
1552 /* we transfer shorts */
1554 /* ok now decide if it is an in or output */
1555 if ((ide_inb(device, ATA_SECT_CNT)&0x02)==0) {
1556 AT_PRINTF("Write to device\n");
1557 output_data_shorts(device,(unsigned short *)buffer,n);
1559 AT_PRINTF("Read from device @ %p shorts %d\n",buffer,n);
1560 input_data_shorts(device,(unsigned short *)buffer,n);
1563 udelay(5000); /* seems that some CD ROMs need this... */
1564 mask = ATA_STAT_BUSY|ATA_STAT_ERR;
1566 c = atapi_wait_mask(device,ATAPI_TIME_OUT,mask,res);
1567 if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) {
1568 err=(ide_inb(device,ATA_ERROR_REG) >> 4);
1569 AT_PRINTF("atapi_issue 2 returned sense key %X status %X\n",err,c);
1574 ide_led (DEVICE_LED(device), 0); /* LED off */
1579 * sending the command to atapi_issue. If an status other than good
1580 * returns, an request_sense will be issued
1583 #define ATAPI_DRIVE_NOT_READY 100
1584 #define ATAPI_UNIT_ATTN 10
1586 unsigned char atapi_issue_autoreq (int device,
1589 unsigned char *buffer,
1592 unsigned char sense_data[18],sense_ccb[12];
1593 unsigned char res,key,asc,ascq;
1594 int notready,unitattn;
1596 #ifdef CONFIG_AMIGAONEG3SE
1598 unsigned int timeout, retrycnt;
1600 s = getenv("ide_cd_timeout");
1601 timeout = s ? (simple_strtol(s, NULL, 10)*1000000)/5 : 0;
1606 unitattn=ATAPI_UNIT_ATTN;
1607 notready=ATAPI_DRIVE_NOT_READY;
1610 res= atapi_issue(device,ccb,ccblen,buffer,buflen);
1612 return (0); /* Ok */
1615 return (0xFF); /* error */
1617 AT_PRINTF("(auto_req)atapi_issue returned sense key %X\n",res);
1619 memset(sense_ccb,0,sizeof(sense_ccb));
1620 memset(sense_data,0,sizeof(sense_data));
1621 sense_ccb[0]=ATAPI_CMD_REQ_SENSE;
1622 sense_ccb[4]=18; /* allocation Length */
1624 res=atapi_issue(device,sense_ccb,12,sense_data,18);
1625 key=(sense_data[2]&0xF);
1626 asc=(sense_data[12]);
1627 ascq=(sense_data[13]);
1629 AT_PRINTF("ATAPI_CMD_REQ_SENSE returned %x\n",res);
1630 AT_PRINTF(" Sense page: %02X key %02X ASC %02X ASCQ %02X\n",
1637 return 0; /* ok device ready */
1639 if((key==6)|| (asc==0x29) || (asc==0x28)) { /* Unit Attention */
1644 printf("Unit Attention, tried %d\n",ATAPI_UNIT_ATTN);
1647 if((asc==0x4) && (ascq==0x1)) { /* not ready, but will be ready soon */
1652 printf("Drive not ready, tried %d times\n",ATAPI_DRIVE_NOT_READY);
1656 AT_PRINTF("Media not present\n");
1660 #ifdef CONFIG_AMIGAONEG3SE
1661 if ((sense_data[2]&0xF)==0x0B) {
1662 AT_PRINTF("ABORTED COMMAND...retry\n");
1668 if ((sense_data[2]&0xf) == 0x02 &&
1669 sense_data[12] == 0x04 &&
1670 sense_data[13] == 0x01 ) {
1671 AT_PRINTF("Waiting for unit to become active\n");
1677 #endif /* CONFIG_AMIGAONEG3SE */
1679 printf ("ERROR: Unknown Sense key %02X ASC %02X ASCQ %02X\n",key,asc,ascq);
1681 AT_PRINTF ("ERROR Sense key %02X ASC %02X ASCQ %02X\n",key,asc,ascq);
1686 static void atapi_inquiry(block_dev_desc_t * dev_desc)
1688 unsigned char ccb[12]; /* Command descriptor block */
1689 unsigned char iobuf[64]; /* temp buf */
1693 device=dev_desc->dev;
1694 dev_desc->type=DEV_TYPE_UNKNOWN; /* not yet valid */
1695 dev_desc->block_read=atapi_read;
1697 memset(ccb,0,sizeof(ccb));
1698 memset(iobuf,0,sizeof(iobuf));
1700 ccb[0]=ATAPI_CMD_INQUIRY;
1701 ccb[4]=40; /* allocation Legnth */
1702 c=atapi_issue_autoreq(device,ccb,12,(unsigned char *)iobuf,40);
1704 AT_PRINTF("ATAPI_CMD_INQUIRY returned %x\n",c);
1708 /* copy device ident strings */
1709 ident_cpy(dev_desc->vendor,&iobuf[8],8);
1710 ident_cpy(dev_desc->product,&iobuf[16],16);
1711 ident_cpy(dev_desc->revision,&iobuf[32],5);
1716 dev_desc->type=iobuf[0] & 0x1f;
1718 if ((iobuf[1]&0x80)==0x80)
1719 dev_desc->removable = 1;
1721 dev_desc->removable = 0;
1723 memset(ccb,0,sizeof(ccb));
1724 memset(iobuf,0,sizeof(iobuf));
1725 ccb[0]=ATAPI_CMD_START_STOP;
1726 ccb[4]=0x03; /* start */
1728 c=atapi_issue_autoreq(device,ccb,12,(unsigned char *)iobuf,0);
1730 AT_PRINTF("ATAPI_CMD_START_STOP returned %x\n",c);
1734 memset(ccb,0,sizeof(ccb));
1735 memset(iobuf,0,sizeof(iobuf));
1736 c=atapi_issue_autoreq(device,ccb,12,(unsigned char *)iobuf,0);
1738 AT_PRINTF("ATAPI_CMD_UNIT_TEST_READY returned %x\n",c);
1742 memset(ccb,0,sizeof(ccb));
1743 memset(iobuf,0,sizeof(iobuf));
1744 ccb[0]=ATAPI_CMD_READ_CAP;
1745 c=atapi_issue_autoreq(device,ccb,12,(unsigned char *)iobuf,8);
1746 AT_PRINTF("ATAPI_CMD_READ_CAP returned %x\n",c);
1750 AT_PRINTF("Read Cap: LBA %02X%02X%02X%02X blksize %02X%02X%02X%02X\n",
1751 iobuf[0],iobuf[1],iobuf[2],iobuf[3],
1752 iobuf[4],iobuf[5],iobuf[6],iobuf[7]);
1754 dev_desc->lba =((unsigned long)iobuf[0]<<24) +
1755 ((unsigned long)iobuf[1]<<16) +
1756 ((unsigned long)iobuf[2]<< 8) +
1757 ((unsigned long)iobuf[3]);
1758 dev_desc->blksz=((unsigned long)iobuf[4]<<24) +
1759 ((unsigned long)iobuf[5]<<16) +
1760 ((unsigned long)iobuf[6]<< 8) +
1761 ((unsigned long)iobuf[7]);
1768 * we transfer only one block per command, since the multiple DRQ per
1769 * command is not yet implemented
1771 #define ATAPI_READ_MAX_BYTES 2048 /* we read max 2kbytes */
1772 #define ATAPI_READ_BLOCK_SIZE 2048 /* assuming CD part */
1773 #define ATAPI_READ_MAX_BLOCK ATAPI_READ_MAX_BYTES/ATAPI_READ_BLOCK_SIZE /* max blocks */
1775 ulong atapi_read (int device, ulong blknr, ulong blkcnt, ulong *buffer)
1778 unsigned char ccb[12]; /* Command descriptor block */
1781 AT_PRINTF("atapi_read dev %d start %lX, blocks %lX buffer at %lX\n",
1782 device, blknr, blkcnt, (ulong)buffer);
1785 if (blkcnt>ATAPI_READ_MAX_BLOCK) {
1786 cnt=ATAPI_READ_MAX_BLOCK;
1790 ccb[0]=ATAPI_CMD_READ_12;
1791 ccb[1]=0; /* reserved */
1792 ccb[2]=(unsigned char) (blknr>>24) & 0xFF; /* MSB Block */
1793 ccb[3]=(unsigned char) (blknr>>16) & 0xFF; /* */
1794 ccb[4]=(unsigned char) (blknr>> 8) & 0xFF;
1795 ccb[5]=(unsigned char) blknr & 0xFF; /* LSB Block */
1796 ccb[6]=(unsigned char) (cnt >>24) & 0xFF; /* MSB Block count */
1797 ccb[7]=(unsigned char) (cnt >>16) & 0xFF;
1798 ccb[8]=(unsigned char) (cnt >> 8) & 0xFF;
1799 ccb[9]=(unsigned char) cnt & 0xFF; /* LSB Block */
1800 ccb[10]=0; /* reserved */
1801 ccb[11]=0; /* reserved */
1803 if (atapi_issue_autoreq(device,ccb,12,
1804 (unsigned char *)buffer,
1805 cnt*ATAPI_READ_BLOCK_SIZE) == 0xFF) {
1811 buffer+=cnt*(ATAPI_READ_BLOCK_SIZE/4); /* ulong blocksize in ulong */
1812 } while (blkcnt > 0);
1816 /* ------------------------------------------------------------------------- */
1818 #endif /* CONFIG_ATAPI */
1822 "ide - IDE sub-system\n",
1823 "reset - reset IDE controller\n"
1824 "ide info - show available IDE devices\n"
1825 "ide device [dev] - show or set current device\n"
1826 "ide part [dev] - print partition table of one or all IDE devices\n"
1827 "ide read addr blk# cnt\n"
1828 "ide write addr blk# cnt - read/write `cnt'"
1829 " blocks starting at block `blk#'\n"
1830 " to/from memory address `addr'\n"
1834 diskboot, 3, 1, do_diskboot,
1835 "diskboot- boot from IDE device\n",
1836 "loadAddr dev:part\n"
1839 #endif /* CONFIG_COMMANDS & CFG_CMD_IDE */