board/wandboard/wandboard.c

   1 /*
   2  * Copyright (C) 2013 Freescale Semiconductor, Inc.
   3  *
   4  * Author: Fabio Estevam <fabio.estevam@freescale.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #include <asm/arch/clock.h>
  10 #include <asm/arch/crm_regs.h>
  11 #include <asm/arch/iomux.h>
  12 #include <asm/arch/imx-regs.h>
  13 #include <asm/arch/mx6-pins.h>
  14 #include <asm/arch/mxc_hdmi.h>
  15 #include <asm/arch/sys_proto.h>
  16 #include <asm/gpio.h>
  17 #include <asm/imx-common/iomux-v3.h>
  18 #include <asm/imx-common/boot_mode.h>
  19 #include <asm/io.h>
  20 #include <asm/sizes.h>
  21 #include <common.h>
  22 #include <fsl_esdhc.h>
  23 #include <ipu_pixfmt.h>
  24 #include <mmc.h>
  25 #include <miiphy.h>
  26 #include <netdev.h>
  27 #include <linux/fb.h>
  28
  29 DECLARE_GLOBAL_DATA_PTR;
  30
  31 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  32         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |                 \
  33         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  34
  35 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |                    \
  36         PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |                 \
  37         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  38
  39 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  40         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
  41
  42 #define USDHC1_CD_GPIO          IMX_GPIO_NR(1, 2)
  43 #define USDHC3_CD_GPIO          IMX_GPIO_NR(3, 9)
  44 #define ETH_PHY_RESET           IMX_GPIO_NR(3, 29)
  45
  46 int dram_init(void)
  47 {
  48         gd->ram_size = (phys_size_t)CONFIG_DDR_MB * 1024 * 1024;
  49
  50         return 0;
  51 }
  52
  53 static iomux_v3_cfg_t const uart1_pads[] = {
  54         MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  55         MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  56 };
  57
  58 iomux_v3_cfg_t const usdhc1_pads[] = {
  59         MX6_PAD_SD1_CLK__SD1_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  60         MX6_PAD_SD1_CMD__SD1_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  61         MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  62         MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  63         MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  64         MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  65         /* Carrier MicroSD Card Detect */
  66         MX6_PAD_GPIO_2__GPIO1_IO02      | MUX_PAD_CTRL(NO_PAD_CTRL),
  67 };
  68
  69 static iomux_v3_cfg_t const usdhc3_pads[] = {
  70         MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  71         MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  72         MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  73         MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  74         MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  75         MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  76         /* SOM MicroSD Card Detect */
  77         MX6_PAD_EIM_DA9__GPIO3_IO09     | MUX_PAD_CTRL(NO_PAD_CTRL),
  78 };
  79
  80 static iomux_v3_cfg_t const enet_pads[] = {
  81         MX6_PAD_ENET_MDIO__ENET_MDIO            | MUX_PAD_CTRL(ENET_PAD_CTRL),
  82         MX6_PAD_ENET_MDC__ENET_MDC              | MUX_PAD_CTRL(ENET_PAD_CTRL),
  83         MX6_PAD_RGMII_TXC__RGMII_TXC    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  84         MX6_PAD_RGMII_TD0__RGMII_TD0    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  85         MX6_PAD_RGMII_TD1__RGMII_TD1    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  86         MX6_PAD_RGMII_TD2__RGMII_TD2    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  87         MX6_PAD_RGMII_TD3__RGMII_TD3    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  88         MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL      | MUX_PAD_CTRL(ENET_PAD_CTRL),
  89         MX6_PAD_ENET_REF_CLK__ENET_TX_CLK       | MUX_PAD_CTRL(ENET_PAD_CTRL),
  90         MX6_PAD_RGMII_RXC__RGMII_RXC    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  91         MX6_PAD_RGMII_RD0__RGMII_RD0    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  92         MX6_PAD_RGMII_RD1__RGMII_RD1    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  93         MX6_PAD_RGMII_RD2__RGMII_RD2    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  94         MX6_PAD_RGMII_RD3__RGMII_RD3    | MUX_PAD_CTRL(ENET_PAD_CTRL),
  95         MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL      | MUX_PAD_CTRL(ENET_PAD_CTRL),
  96         /* AR8031 PHY Reset */
  97         MX6_PAD_EIM_D29__GPIO3_IO29             | MUX_PAD_CTRL(NO_PAD_CTRL),
  98 };
  99
 100 static void setup_iomux_uart(void)
 101 {
 102         imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
 103 }
 104
 105 static void setup_iomux_enet(void)
 106 {
 107         imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
 108
 109         /* Reset AR8031 PHY */
 110         gpio_direction_output(ETH_PHY_RESET, 0);
 111         udelay(500);
 112         gpio_set_value(ETH_PHY_RESET, 1);
 113 }
 114
 115 static struct fsl_esdhc_cfg usdhc_cfg[2] = {
 116         {USDHC3_BASE_ADDR},
 117         {USDHC1_BASE_ADDR},
 118 };
 119
 120 int board_mmc_getcd(struct mmc *mmc)
 121 {
 122         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 123         int ret = 0;
 124
 125         switch (cfg->esdhc_base) {
 126         case USDHC1_BASE_ADDR:
 127                 ret = !gpio_get_value(USDHC1_CD_GPIO);
 128                 break;
 129         case USDHC3_BASE_ADDR:
 130                 ret = !gpio_get_value(USDHC3_CD_GPIO);
 131                 break;
 132         }
 133
 134         return ret;
 135 }
 136
 137 int board_mmc_init(bd_t *bis)
 138 {
 139         s32 status = 0;
 140         u32 index = 0;
 141
 142         /*
 143          * Following map is done:
 144          * (U-boot device node)    (Physical Port)
 145          * mmc0                    SOM MicroSD
 146          * mmc1                    Carrier board MicroSD
 147          */
 148         for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
 149                 switch (index) {
 150                 case 0:
 151                         imx_iomux_v3_setup_multiple_pads(
 152                                 usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
 153                         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 154                         usdhc_cfg[0].max_bus_width = 4;
 155                         gpio_direction_input(USDHC3_CD_GPIO);
 156                         break;
 157                 case 1:
 158                         imx_iomux_v3_setup_multiple_pads(
 159                                 usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
 160                         usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
 161                         usdhc_cfg[1].max_bus_width = 4;
 162                         gpio_direction_input(USDHC1_CD_GPIO);
 163                         break;
 164                 default:
 165                         printf("Warning: you configured more USDHC controllers"
 166                                "(%d) then supported by the board (%d)\n",
 167                                index + 1, CONFIG_SYS_FSL_USDHC_NUM);
 168                         return status;
 169                 }
 170
 171                 status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
 172         }
 173
 174         return status;
 175 }
 176
 177 static int mx6_rgmii_rework(struct phy_device *phydev)
 178 {
 179         unsigned short val;
 180
 181         /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
 182         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
 183         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
 184         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
 185
 186         val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
 187         val &= 0xffe3;
 188         val |= 0x18;
 189         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
 190
 191         /* introduce tx clock delay */
 192         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
 193         val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
 194         val |= 0x0100;
 195         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
 196
 197         return 0;
 198 }
 199
 200 int board_phy_config(struct phy_device *phydev)
 201 {
 202         mx6_rgmii_rework(phydev);
 203
 204         if (phydev->drv->config)
 205                 phydev->drv->config(phydev);
 206
 207         return 0;
 208 }
 209
 210 #if defined(CONFIG_VIDEO_IPUV3)
 211 static struct fb_videomode const hdmi = {
 212         .name           = "HDMI",
 213         .refresh        = 60,
 214         .xres           = 1024,
 215         .yres           = 768,
 216         .pixclock       = 15385,
 217         .left_margin    = 220,
 218         .right_margin   = 40,
 219         .upper_margin   = 21,
 220         .lower_margin   = 7,
 221         .hsync_len      = 60,
 222         .vsync_len      = 10,
 223         .sync           = FB_SYNC_EXT,
 224         .vmode          = FB_VMODE_NONINTERLACED
 225 };
 226
 227 int board_video_skip(void)
 228 {
 229         int ret;
 230
 231         ret = ipuv3_fb_init(&hdmi, 0, IPU_PIX_FMT_RGB24);
 232
 233         if (ret) {
 234                 printf("HDMI cannot be configured: %d\n", ret);
 235                 return ret;
 236         }
 237
 238         imx_enable_hdmi_phy();
 239
 240         return ret;
 241 }
 242
 243 static void setup_display(void)
 244 {
 245         struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 246         int reg;
 247
 248         enable_ipu_clock();
 249         imx_setup_hdmi();
 250
 251         reg = readl(&mxc_ccm->chsccdr);
 252         reg |= (CHSCCDR_CLK_SEL_LDB_DI0
 253                 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
 254         writel(reg, &mxc_ccm->chsccdr);
 255 }
 256 #endif /* CONFIG_VIDEO_IPUV3 */
 257
 258 int board_eth_init(bd_t *bis)
 259 {
 260         setup_iomux_enet();
 261
 262         return cpu_eth_init(bis);
 263 }
 264
 265 int board_early_init_f(void)
 266 {
 267         setup_iomux_uart();
 268 #if defined(CONFIG_VIDEO_IPUV3)
 269         setup_display();
 270 #endif
 271         return 0;
 272 }
 273
 274 /*
 275  * Do not overwrite the console
 276  * Use always serial for U-Boot console
 277  */
 278 int overwrite_console(void)
 279 {
 280         return 1;
 281 }
 282
 283 #ifdef CONFIG_CMD_BMODE
 284 static const struct boot_mode board_boot_modes[] = {
 285         /* 4 bit bus width */
 286         {"mmc0",          MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
 287         {"mmc1",          MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
 288         {NULL,   0},
 289 };
 290 #endif
 291
 292 int board_late_init(void)
 293 {
 294 #ifdef CONFIG_CMD_BMODE
 295         add_board_boot_modes(board_boot_modes);
 296 #endif
 297
 298         return 0;
 299 }
 300
 301 int board_init(void)
 302 {
 303         /* address of boot parameters */
 304         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 305
 306         return 0;
 307 }
 308
 309 int checkboard(void)
 310 {
 311         puts("Board: Wandboard\n");
 312
 313         return 0;
 314 }