board/ti/am57xx/board.c

   1 /*
   2  * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com
   3  *
   4  * Author: Felipe Balbi <balbi@ti.com>
   5  *
   6  * Based on board/ti/dra7xx/evm.c
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #include <common.h>
  12 #include <palmas.h>
  13 #include <sata.h>
  14 #include <usb.h>
  15 #include <asm/omap_common.h>
  16 #include <asm/omap_sec_common.h>
  17 #include <asm/emif.h>
  18 #include <asm/gpio.h>
  19 #include <asm/arch/gpio.h>
  20 #include <asm/arch/clock.h>
  21 #include <asm/arch/dra7xx_iodelay.h>
  22 #include <asm/arch/sys_proto.h>
  23 #include <asm/arch/mmc_host_def.h>
  24 #include <asm/arch/sata.h>
  25 #include <asm/arch/gpio.h>
  26 #include <asm/arch/omap.h>
  27 #include <environment.h>
  28 #include <usb.h>
  29 #include <linux/usb/gadget.h>
  30 #include <dwc3-uboot.h>
  31 #include <dwc3-omap-uboot.h>
  32 #include <ti-usb-phy-uboot.h>
  33
  34 #include "../common/board_detect.h"
  35 #include "mux_data.h"
  36
  37 #define board_is_x15()          board_ti_is("BBRDX15_")
  38 #define board_is_x15_revb1()    (board_ti_is("BBRDX15_") && \
  39                                  (strncmp("B.10", board_ti_get_rev(), 3) <= 0))
  40 #define board_is_am572x_evm()   board_ti_is("AM572PM_")
  41 #define board_is_am572x_evm_reva3()     \
  42                                 (board_ti_is("AM572PM_") && \
  43                                  (strncmp("A.30", board_ti_get_rev(), 3) <= 0))
  44 #define board_is_am572x_idk()   board_ti_is("AM572IDK")
  45 #define board_is_am571x_idk()   board_ti_is("AM571IDK")
  46
  47 #ifdef CONFIG_DRIVER_TI_CPSW
  48 #include <cpsw.h>
  49 #endif
  50
  51 DECLARE_GLOBAL_DATA_PTR;
  52
  53 #define GPIO_ETH_LCD            GPIO_TO_PIN(2, 22)
  54 /* GPIO 7_11 */
  55 #define GPIO_DDR_VTT_EN 203
  56
  57 /* Touch screen controller to identify the LCD */
  58 #define OSD_TS_FT_BUS_ADDRESS   0
  59 #define OSD_TS_FT_CHIP_ADDRESS  0x38
  60 #define OSD_TS_FT_REG_ID        0xA3
  61 /*
  62  * Touchscreen IDs for various OSD panels
  63  * Ref: http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf
  64  */
  65 /* Used on newer osd101t2587 Panels */
  66 #define OSD_TS_FT_ID_5x46       0x54
  67 /* Used on older osd101t2045 Panels */
  68 #define OSD_TS_FT_ID_5606       0x08
  69
  70 #define SYSINFO_BOARD_NAME_MAX_LEN      45
  71
  72 #define TPS65903X_PRIMARY_SECONDARY_PAD2        0xFB
  73 #define TPS65903X_PAD2_POWERHOLD_MASK           0x20
  74
  75 const struct omap_sysinfo sysinfo = {
  76         "Board: UNKNOWN(BeagleBoard X15?) REV UNKNOWN\n"
  77 };
  78
  79 static const struct dmm_lisa_map_regs beagle_x15_lisa_regs = {
  80         .dmm_lisa_map_3 = 0x80740300,
  81         .is_ma_present  = 0x1
  82 };
  83
  84 static const struct dmm_lisa_map_regs am571x_idk_lisa_regs = {
  85         .dmm_lisa_map_3 = 0x80640100,
  86         .is_ma_present  = 0x1
  87 };
  88
  89 void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs)
  90 {
  91         if (board_is_am571x_idk())
  92                 *dmm_lisa_regs = &am571x_idk_lisa_regs;
  93         else
  94                 *dmm_lisa_regs = &beagle_x15_lisa_regs;
  95 }
  96
  97 static const struct emif_regs beagle_x15_emif1_ddr3_532mhz_emif_regs = {
  98         .sdram_config_init              = 0x61851b32,
  99         .sdram_config                   = 0x61851b32,
 100         .sdram_config2                  = 0x08000000,
 101         .ref_ctrl                       = 0x000040F1,
 102         .ref_ctrl_final                 = 0x00001035,
 103         .sdram_tim1                     = 0xcccf36ab,
 104         .sdram_tim2                     = 0x308f7fda,
 105         .sdram_tim3                     = 0x409f88a8,
 106         .read_idle_ctrl                 = 0x00050000,
 107         .zq_config                      = 0x5007190b,
 108         .temp_alert_config              = 0x00000000,
 109         .emif_ddr_phy_ctlr_1_init       = 0x0024400b,
 110         .emif_ddr_phy_ctlr_1            = 0x0e24400b,
 111         .emif_ddr_ext_phy_ctrl_1        = 0x10040100,
 112         .emif_ddr_ext_phy_ctrl_2        = 0x00910091,
 113         .emif_ddr_ext_phy_ctrl_3        = 0x00950095,
 114         .emif_ddr_ext_phy_ctrl_4        = 0x009b009b,
 115         .emif_ddr_ext_phy_ctrl_5        = 0x009e009e,
 116         .emif_rd_wr_lvl_rmp_win         = 0x00000000,
 117         .emif_rd_wr_lvl_rmp_ctl         = 0x80000000,
 118         .emif_rd_wr_lvl_ctl             = 0x00000000,
 119         .emif_rd_wr_exec_thresh         = 0x00000305
 120 };
 121
 122 /* Ext phy ctrl regs 1-35 */
 123 static const u32 beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs[] = {
 124         0x10040100,
 125         0x00910091,
 126         0x00950095,
 127         0x009B009B,
 128         0x009E009E,
 129         0x00980098,
 130         0x00340034,
 131         0x00350035,
 132         0x00340034,
 133         0x00310031,
 134         0x00340034,
 135         0x007F007F,
 136         0x007F007F,
 137         0x007F007F,
 138         0x007F007F,
 139         0x007F007F,
 140         0x00480048,
 141         0x004A004A,
 142         0x00520052,
 143         0x00550055,
 144         0x00500050,
 145         0x00000000,
 146         0x00600020,
 147         0x40011080,
 148         0x08102040,
 149         0x0,
 150         0x0,
 151         0x0,
 152         0x0,
 153         0x0,
 154         0x0,
 155         0x0,
 156         0x0,
 157         0x0,
 158         0x0
 159 };
 160
 161 static const struct emif_regs beagle_x15_emif2_ddr3_532mhz_emif_regs = {
 162         .sdram_config_init              = 0x61851b32,
 163         .sdram_config                   = 0x61851b32,
 164         .sdram_config2                  = 0x08000000,
 165         .ref_ctrl                       = 0x000040F1,
 166         .ref_ctrl_final                 = 0x00001035,
 167         .sdram_tim1                     = 0xcccf36b3,
 168         .sdram_tim2                     = 0x308f7fda,
 169         .sdram_tim3                     = 0x407f88a8,
 170         .read_idle_ctrl                 = 0x00050000,
 171         .zq_config                      = 0x5007190b,
 172         .temp_alert_config              = 0x00000000,
 173         .emif_ddr_phy_ctlr_1_init       = 0x0024400b,
 174         .emif_ddr_phy_ctlr_1            = 0x0e24400b,
 175         .emif_ddr_ext_phy_ctrl_1        = 0x10040100,
 176         .emif_ddr_ext_phy_ctrl_2        = 0x00910091,
 177         .emif_ddr_ext_phy_ctrl_3        = 0x00950095,
 178         .emif_ddr_ext_phy_ctrl_4        = 0x009b009b,
 179         .emif_ddr_ext_phy_ctrl_5        = 0x009e009e,
 180         .emif_rd_wr_lvl_rmp_win         = 0x00000000,
 181         .emif_rd_wr_lvl_rmp_ctl         = 0x80000000,
 182         .emif_rd_wr_lvl_ctl             = 0x00000000,
 183         .emif_rd_wr_exec_thresh         = 0x00000305
 184 };
 185
 186 static const u32 beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs[] = {
 187         0x10040100,
 188         0x00910091,
 189         0x00950095,
 190         0x009B009B,
 191         0x009E009E,
 192         0x00980098,
 193         0x00340034,
 194         0x00350035,
 195         0x00340034,
 196         0x00310031,
 197         0x00340034,
 198         0x007F007F,
 199         0x007F007F,
 200         0x007F007F,
 201         0x007F007F,
 202         0x007F007F,
 203         0x00480048,
 204         0x004A004A,
 205         0x00520052,
 206         0x00550055,
 207         0x00500050,
 208         0x00000000,
 209         0x00600020,
 210         0x40011080,
 211         0x08102040,
 212         0x0,
 213         0x0,
 214         0x0,
 215         0x0,
 216         0x0,
 217         0x0,
 218         0x0,
 219         0x0,
 220         0x0,
 221         0x0
 222 };
 223
 224 void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
 225 {
 226         switch (emif_nr) {
 227         case 1:
 228                 *regs = &beagle_x15_emif1_ddr3_532mhz_emif_regs;
 229                 break;
 230         case 2:
 231                 *regs = &beagle_x15_emif2_ddr3_532mhz_emif_regs;
 232                 break;
 233         }
 234 }
 235
 236 void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr, const u32 **regs, u32 *size)
 237 {
 238         switch (emif_nr) {
 239         case 1:
 240                 *regs = beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs;
 241                 *size = ARRAY_SIZE(beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs);
 242                 break;
 243         case 2:
 244                 *regs = beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs;
 245                 *size = ARRAY_SIZE(beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs);
 246                 break;
 247         }
 248 }
 249
 250 struct vcores_data beagle_x15_volts = {
 251         .mpu.value[OPP_NOM]     = VDD_MPU_DRA7_NOM,
 252         .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM,
 253         .mpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 254         .mpu.addr               = TPS659038_REG_ADDR_SMPS12,
 255         .mpu.pmic               = &tps659038,
 256         .mpu.abb_tx_done_mask   = OMAP_ABB_MPU_TXDONE_MASK,
 257
 258         .eve.value[OPP_NOM]     = VDD_EVE_DRA7_NOM,
 259         .eve.value[OPP_OD]      = VDD_EVE_DRA7_OD,
 260         .eve.value[OPP_HIGH]    = VDD_EVE_DRA7_HIGH,
 261         .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM,
 262         .eve.efuse.reg[OPP_OD]  = STD_FUSE_OPP_VMIN_DSPEVE_OD,
 263         .eve.efuse.reg[OPP_HIGH]        = STD_FUSE_OPP_VMIN_DSPEVE_HIGH,
 264         .eve.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 265         .eve.addr               = TPS659038_REG_ADDR_SMPS45,
 266         .eve.pmic               = &tps659038,
 267         .eve.abb_tx_done_mask   = OMAP_ABB_EVE_TXDONE_MASK,
 268
 269         .gpu.value[OPP_NOM]     = VDD_GPU_DRA7_NOM,
 270         .gpu.value[OPP_OD]      = VDD_GPU_DRA7_OD,
 271         .gpu.value[OPP_HIGH]    = VDD_GPU_DRA7_HIGH,
 272         .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM,
 273         .gpu.efuse.reg[OPP_OD]  = STD_FUSE_OPP_VMIN_GPU_OD,
 274         .gpu.efuse.reg[OPP_HIGH]        = STD_FUSE_OPP_VMIN_GPU_HIGH,
 275         .gpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 276         .gpu.addr               = TPS659038_REG_ADDR_SMPS45,
 277         .gpu.pmic               = &tps659038,
 278         .gpu.abb_tx_done_mask   = OMAP_ABB_GPU_TXDONE_MASK,
 279
 280         .core.value[OPP_NOM]    = VDD_CORE_DRA7_NOM,
 281         .core.efuse.reg[OPP_NOM]        = STD_FUSE_OPP_VMIN_CORE_NOM,
 282         .core.efuse.reg_bits    = DRA752_EFUSE_REGBITS,
 283         .core.addr              = TPS659038_REG_ADDR_SMPS6,
 284         .core.pmic              = &tps659038,
 285
 286         .iva.value[OPP_NOM]     = VDD_IVA_DRA7_NOM,
 287         .iva.value[OPP_OD]      = VDD_IVA_DRA7_OD,
 288         .iva.value[OPP_HIGH]    = VDD_IVA_DRA7_HIGH,
 289         .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM,
 290         .iva.efuse.reg[OPP_OD]  = STD_FUSE_OPP_VMIN_IVA_OD,
 291         .iva.efuse.reg[OPP_HIGH]        = STD_FUSE_OPP_VMIN_IVA_HIGH,
 292         .iva.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 293         .iva.addr               = TPS659038_REG_ADDR_SMPS45,
 294         .iva.pmic               = &tps659038,
 295         .iva.abb_tx_done_mask   = OMAP_ABB_IVA_TXDONE_MASK,
 296 };
 297
 298 struct vcores_data am572x_idk_volts = {
 299         .mpu.value[OPP_NOM]     = VDD_MPU_DRA7_NOM,
 300         .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM,
 301         .mpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 302         .mpu.addr               = TPS659038_REG_ADDR_SMPS12,
 303         .mpu.pmic               = &tps659038,
 304         .mpu.abb_tx_done_mask   = OMAP_ABB_MPU_TXDONE_MASK,
 305
 306         .eve.value[OPP_NOM]     = VDD_EVE_DRA7_NOM,
 307         .eve.value[OPP_OD]      = VDD_EVE_DRA7_OD,
 308         .eve.value[OPP_HIGH]    = VDD_EVE_DRA7_HIGH,
 309         .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM,
 310         .eve.efuse.reg[OPP_OD]  = STD_FUSE_OPP_VMIN_DSPEVE_OD,
 311         .eve.efuse.reg[OPP_HIGH]        = STD_FUSE_OPP_VMIN_DSPEVE_HIGH,
 312         .eve.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 313         .eve.addr               = TPS659038_REG_ADDR_SMPS45,
 314         .eve.pmic               = &tps659038,
 315         .eve.abb_tx_done_mask   = OMAP_ABB_EVE_TXDONE_MASK,
 316
 317         .gpu.value[OPP_NOM]     = VDD_GPU_DRA7_NOM,
 318         .gpu.value[OPP_OD]      = VDD_GPU_DRA7_OD,
 319         .gpu.value[OPP_HIGH]    = VDD_GPU_DRA7_HIGH,
 320         .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM,
 321         .gpu.efuse.reg[OPP_OD]  = STD_FUSE_OPP_VMIN_GPU_OD,
 322         .gpu.efuse.reg[OPP_HIGH]        = STD_FUSE_OPP_VMIN_GPU_HIGH,
 323         .gpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 324         .gpu.addr               = TPS659038_REG_ADDR_SMPS6,
 325         .gpu.pmic               = &tps659038,
 326         .gpu.abb_tx_done_mask   = OMAP_ABB_GPU_TXDONE_MASK,
 327
 328         .core.value[OPP_NOM]    = VDD_CORE_DRA7_NOM,
 329         .core.efuse.reg[OPP_NOM]        = STD_FUSE_OPP_VMIN_CORE_NOM,
 330         .core.efuse.reg_bits    = DRA752_EFUSE_REGBITS,
 331         .core.addr              = TPS659038_REG_ADDR_SMPS7,
 332         .core.pmic              = &tps659038,
 333
 334         .iva.value[OPP_NOM]     = VDD_IVA_DRA7_NOM,
 335         .iva.value[OPP_OD]      = VDD_IVA_DRA7_OD,
 336         .iva.value[OPP_HIGH]    = VDD_IVA_DRA7_HIGH,
 337         .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM,
 338         .iva.efuse.reg[OPP_OD]  = STD_FUSE_OPP_VMIN_IVA_OD,
 339         .iva.efuse.reg[OPP_HIGH]        = STD_FUSE_OPP_VMIN_IVA_HIGH,
 340         .iva.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 341         .iva.addr               = TPS659038_REG_ADDR_SMPS8,
 342         .iva.pmic               = &tps659038,
 343         .iva.abb_tx_done_mask   = OMAP_ABB_IVA_TXDONE_MASK,
 344 };
 345
 346 struct vcores_data am571x_idk_volts = {
 347         .mpu.value[OPP_NOM]     = VDD_MPU_DRA7_NOM,
 348         .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM,
 349         .mpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 350         .mpu.addr               = TPS659038_REG_ADDR_SMPS12,
 351         .mpu.pmic               = &tps659038,
 352         .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK,
 353
 354         .eve.value[OPP_NOM]     = VDD_EVE_DRA7_NOM,
 355         .eve.value[OPP_OD]      = VDD_EVE_DRA7_OD,
 356         .eve.value[OPP_HIGH]    = VDD_EVE_DRA7_HIGH,
 357         .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM,
 358         .eve.efuse.reg[OPP_OD]  = STD_FUSE_OPP_VMIN_DSPEVE_OD,
 359         .eve.efuse.reg[OPP_HIGH]        = STD_FUSE_OPP_VMIN_DSPEVE_HIGH,
 360         .eve.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 361         .eve.addr               = TPS659038_REG_ADDR_SMPS45,
 362         .eve.pmic               = &tps659038,
 363         .eve.abb_tx_done_mask   = OMAP_ABB_EVE_TXDONE_MASK,
 364
 365         .gpu.value[OPP_NOM]     = VDD_GPU_DRA7_NOM,
 366         .gpu.value[OPP_OD]      = VDD_GPU_DRA7_OD,
 367         .gpu.value[OPP_HIGH]    = VDD_GPU_DRA7_HIGH,
 368         .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM,
 369         .gpu.efuse.reg[OPP_OD]  = STD_FUSE_OPP_VMIN_GPU_OD,
 370         .gpu.efuse.reg[OPP_HIGH]        = STD_FUSE_OPP_VMIN_GPU_HIGH,
 371         .gpu.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 372         .gpu.addr               = TPS659038_REG_ADDR_SMPS6,
 373         .gpu.pmic               = &tps659038,
 374         .gpu.abb_tx_done_mask   = OMAP_ABB_GPU_TXDONE_MASK,
 375
 376         .core.value[OPP_NOM]    = VDD_CORE_DRA7_NOM,
 377         .core.efuse.reg[OPP_NOM]        = STD_FUSE_OPP_VMIN_CORE_NOM,
 378         .core.efuse.reg_bits    = DRA752_EFUSE_REGBITS,
 379         .core.addr              = TPS659038_REG_ADDR_SMPS7,
 380         .core.pmic              = &tps659038,
 381
 382         .iva.value[OPP_NOM]     = VDD_IVA_DRA7_NOM,
 383         .iva.value[OPP_OD]      = VDD_IVA_DRA7_OD,
 384         .iva.value[OPP_HIGH]    = VDD_IVA_DRA7_HIGH,
 385         .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM,
 386         .iva.efuse.reg[OPP_OD]  = STD_FUSE_OPP_VMIN_IVA_OD,
 387         .iva.efuse.reg[OPP_HIGH]        = STD_FUSE_OPP_VMIN_IVA_HIGH,
 388         .iva.efuse.reg_bits     = DRA752_EFUSE_REGBITS,
 389         .iva.addr               = TPS659038_REG_ADDR_SMPS45,
 390         .iva.pmic               = &tps659038,
 391         .iva.abb_tx_done_mask   = OMAP_ABB_IVA_TXDONE_MASK,
 392 };
 393
 394 int get_voltrail_opp(int rail_offset)
 395 {
 396         int opp;
 397
 398         switch (rail_offset) {
 399         case VOLT_MPU:
 400                 opp = DRA7_MPU_OPP;
 401                 break;
 402         case VOLT_CORE:
 403                 opp = DRA7_CORE_OPP;
 404                 break;
 405         case VOLT_GPU:
 406                 opp = DRA7_GPU_OPP;
 407                 break;
 408         case VOLT_EVE:
 409                 opp = DRA7_DSPEVE_OPP;
 410                 break;
 411         case VOLT_IVA:
 412                 opp = DRA7_IVA_OPP;
 413                 break;
 414         default:
 415                 opp = OPP_NOM;
 416         }
 417
 418         return opp;
 419 }
 420
 421
 422 #ifdef CONFIG_SPL_BUILD
 423 /* No env to setup for SPL */
 424 static inline void setup_board_eeprom_env(void) { }
 425
 426 /* Override function to read eeprom information */
 427 void do_board_detect(void)
 428 {
 429         int rc;
 430
 431         rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
 432                                   CONFIG_EEPROM_CHIP_ADDRESS);
 433         if (rc)
 434                 printf("ti_i2c_eeprom_init failed %d\n", rc);
 435 }
 436
 437 #else   /* CONFIG_SPL_BUILD */
 438
 439 /* Override function to read eeprom information: actual i2c read done by SPL*/
 440 void do_board_detect(void)
 441 {
 442         char *bname = NULL;
 443         int rc;
 444
 445         rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
 446                                   CONFIG_EEPROM_CHIP_ADDRESS);
 447         if (rc)
 448                 printf("ti_i2c_eeprom_init failed %d\n", rc);
 449
 450         if (board_is_x15())
 451                 bname = "BeagleBoard X15";
 452         else if (board_is_am572x_evm())
 453                 bname = "AM572x EVM";
 454         else if (board_is_am572x_idk())
 455                 bname = "AM572x IDK";
 456         else if (board_is_am571x_idk())
 457                 bname = "AM571x IDK";
 458
 459         if (bname)
 460                 snprintf(sysinfo.board_string, SYSINFO_BOARD_NAME_MAX_LEN,
 461                          "Board: %s REV %s\n", bname, board_ti_get_rev());
 462 }
 463
 464 static void setup_board_eeprom_env(void)
 465 {
 466         char *name = "beagle_x15";
 467         int rc;
 468
 469         rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
 470                                   CONFIG_EEPROM_CHIP_ADDRESS);
 471         if (rc)
 472                 goto invalid_eeprom;
 473
 474         if (board_is_x15()) {
 475                 if (board_is_x15_revb1())
 476                         name = "beagle_x15_revb1";
 477                 else
 478                         name = "beagle_x15";
 479         } else if (board_is_am572x_evm()) {
 480                 if (board_is_am572x_evm_reva3())
 481                         name = "am57xx_evm_reva3";
 482                 else
 483                         name = "am57xx_evm";
 484         } else if (board_is_am572x_idk()) {
 485                 name = "am572x_idk";
 486         } else if (board_is_am571x_idk()) {
 487                 name = "am571x_idk";
 488         } else {
 489                 printf("Unidentified board claims %s in eeprom header\n",
 490                        board_ti_get_name());
 491         }
 492
 493 invalid_eeprom:
 494         set_board_info_env(name);
 495 }
 496
 497 #endif  /* CONFIG_SPL_BUILD */
 498
 499 void vcores_init(void)
 500 {
 501         if (board_is_am572x_idk())
 502                 *omap_vcores = &am572x_idk_volts;
 503         else if (board_is_am571x_idk())
 504                 *omap_vcores = &am571x_idk_volts;
 505         else
 506                 *omap_vcores = &beagle_x15_volts;
 507 }
 508
 509 void hw_data_init(void)
 510 {
 511         *prcm = &dra7xx_prcm;
 512         *dplls_data = &dra7xx_dplls;
 513         *ctrl = &dra7xx_ctrl;
 514 }
 515
 516 bool am571x_idk_needs_lcd(void)
 517 {
 518         bool needs_lcd;
 519
 520         gpio_request(GPIO_ETH_LCD, "nLCD_Detect");
 521         if (gpio_get_value(GPIO_ETH_LCD))
 522                 needs_lcd = false;
 523         else
 524                 needs_lcd = true;
 525
 526         gpio_free(GPIO_ETH_LCD);
 527
 528         return needs_lcd;
 529 }
 530
 531 int board_init(void)
 532 {
 533         gpmc_init();
 534         gd->bd->bi_boot_params = (CONFIG_SYS_SDRAM_BASE + 0x100);
 535
 536         return 0;
 537 }
 538
 539 void am57x_idk_lcd_detect(void)
 540 {
 541         int r = -ENODEV;
 542         char *idk_lcd = "no";
 543         uint8_t buf = 0;
 544
 545         /* Only valid for IDKs */
 546         if (board_is_x15() || board_is_am572x_evm())
 547                 return;
 548
 549         /* Only AM571x IDK has gpio control detect.. so check that */
 550         if (board_is_am571x_idk() && !am571x_idk_needs_lcd())
 551                 goto out;
 552
 553         r = i2c_set_bus_num(OSD_TS_FT_BUS_ADDRESS);
 554         if (r) {
 555                 printf("%s: Failed to set bus address to %d: %d\n",
 556                        __func__, OSD_TS_FT_BUS_ADDRESS, r);
 557                 goto out;
 558         }
 559         r = i2c_probe(OSD_TS_FT_CHIP_ADDRESS);
 560         if (r) {
 561                 /* AM572x IDK has no explicit settings for optional LCD kit */
 562                 if (board_is_am571x_idk()) {
 563                         printf("%s: Touch screen detect failed: %d!\n",
 564                                __func__, r);
 565                 }
 566                 goto out;
 567         }
 568
 569         /* Read FT ID */
 570         r = i2c_read(OSD_TS_FT_CHIP_ADDRESS, OSD_TS_FT_REG_ID, 1, &buf, 1);
 571         if (r) {
 572                 printf("%s: Touch screen ID read %d:0x%02x[0x%02x] failed:%d\n",
 573                        __func__, OSD_TS_FT_BUS_ADDRESS, OSD_TS_FT_CHIP_ADDRESS,
 574                        OSD_TS_FT_REG_ID, r);
 575                 goto out;
 576         }
 577
 578         switch (buf) {
 579         case OSD_TS_FT_ID_5606:
 580                 idk_lcd = "osd101t2045";
 581                 break;
 582         case OSD_TS_FT_ID_5x46:
 583                 idk_lcd = "osd101t2587";
 584                 break;
 585         default:
 586                 printf("%s: Unidentifed Touch screen ID 0x%02x\n",
 587                        __func__, buf);
 588                 /* we will let default be "no lcd" */
 589         }
 590 out:
 591         setenv("idk_lcd", idk_lcd);
 592         return;
 593 }
 594
 595 int board_late_init(void)
 596 {
 597         setup_board_eeprom_env();
 598         u8 val;
 599
 600         /*
 601          * DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds
 602          * This is the POWERHOLD-in-Low behavior.
 603          */
 604         palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1);
 605
 606         /*
 607          * Default FIT boot on HS devices. Non FIT images are not allowed
 608          * on HS devices.
 609          */
 610         if (get_device_type() == HS_DEVICE)
 611                 setenv("boot_fit", "1");
 612
 613         /*
 614          * Set the GPIO7 Pad to POWERHOLD. This has higher priority
 615          * over DEV_CTRL.DEV_ON bit. This can be reset in case of
 616          * PMIC Power off. So to be on the safer side set it back
 617          * to POWERHOLD mode irrespective of the current state.
 618          */
 619         palmas_i2c_read_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
 620                            &val);
 621         val = val | TPS65903X_PAD2_POWERHOLD_MASK;
 622         palmas_i2c_write_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
 623                             val);
 624
 625         omap_die_id_serial();
 626
 627         am57x_idk_lcd_detect();
 628
 629 #if !defined(CONFIG_SPL_BUILD)
 630         board_ti_set_ethaddr(2);
 631 #endif
 632
 633         return 0;
 634 }
 635
 636 void set_muxconf_regs(void)
 637 {
 638         do_set_mux32((*ctrl)->control_padconf_core_base,
 639                      early_padconf, ARRAY_SIZE(early_padconf));
 640 }
 641
 642 #ifdef CONFIG_IODELAY_RECALIBRATION
 643 void recalibrate_iodelay(void)
 644 {
 645         const struct pad_conf_entry *pconf;
 646         const struct iodelay_cfg_entry *iod;
 647         int pconf_sz, iod_sz;
 648         int ret;
 649
 650         if (board_is_am572x_idk()) {
 651                 pconf = core_padconf_array_essential_am572x_idk;
 652                 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am572x_idk);
 653                 iod = iodelay_cfg_array_am572x_idk;
 654                 iod_sz = ARRAY_SIZE(iodelay_cfg_array_am572x_idk);
 655         } else if (board_is_am571x_idk()) {
 656                 pconf = core_padconf_array_essential_am571x_idk;
 657                 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_am571x_idk);
 658                 iod = iodelay_cfg_array_am571x_idk;
 659                 iod_sz = ARRAY_SIZE(iodelay_cfg_array_am571x_idk);
 660         } else {
 661                 /* Common for X15/GPEVM */
 662                 pconf = core_padconf_array_essential_x15;
 663                 pconf_sz = ARRAY_SIZE(core_padconf_array_essential_x15);
 664                 /* There never was an SR1.0 X15.. So.. */
 665                 if (omap_revision() == DRA752_ES1_1) {
 666                         iod = iodelay_cfg_array_x15_sr1_1;
 667                         iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15_sr1_1);
 668                 } else {
 669                         /* Since full production should switch to SR2.0  */
 670                         iod = iodelay_cfg_array_x15_sr2_0;
 671                         iod_sz = ARRAY_SIZE(iodelay_cfg_array_x15_sr2_0);
 672                 }
 673         }
 674
 675         /* Setup I/O isolation */
 676         ret = __recalibrate_iodelay_start();
 677         if (ret)
 678                 goto err;
 679
 680         /* Do the muxing here */
 681         do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
 682
 683         /* Now do the weird minor deltas that should be safe */
 684         if (board_is_x15() || board_is_am572x_evm()) {
 685                 if (board_is_x15_revb1() || board_is_am572x_evm_reva3()) {
 686                         pconf = core_padconf_array_delta_x15_sr2_0;
 687                         pconf_sz = ARRAY_SIZE(core_padconf_array_delta_x15_sr2_0);
 688                 } else {
 689                         pconf = core_padconf_array_delta_x15_sr1_1;
 690                         pconf_sz = ARRAY_SIZE(core_padconf_array_delta_x15_sr1_1);
 691                 }
 692                 do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
 693         }
 694
 695         if (board_is_am571x_idk()) {
 696                 if (am571x_idk_needs_lcd()) {
 697                         pconf = core_padconf_array_vout_am571x_idk;
 698                         pconf_sz = ARRAY_SIZE(core_padconf_array_vout_am571x_idk);
 699                 } else {
 700                         pconf = core_padconf_array_icss1eth_am571x_idk;
 701                         pconf_sz = ARRAY_SIZE(core_padconf_array_icss1eth_am571x_idk);
 702                 }
 703                 do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
 704         }
 705
 706         /* Setup IOdelay configuration */
 707         ret = do_set_iodelay((*ctrl)->iodelay_config_base, iod, iod_sz);
 708 err:
 709         /* Closeup.. remove isolation */
 710         __recalibrate_iodelay_end(ret);
 711 }
 712 #endif
 713
 714 #if defined(CONFIG_MMC)
 715 int board_mmc_init(bd_t *bis)
 716 {
 717         omap_mmc_init(0, 0, 0, -1, -1);
 718         omap_mmc_init(1, 0, 0, -1, -1);
 719         return 0;
 720 }
 721 #endif
 722
 723 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT)
 724 int spl_start_uboot(void)
 725 {
 726         /* break into full u-boot on 'c' */
 727         if (serial_tstc() && serial_getc() == 'c')
 728                 return 1;
 729
 730 #ifdef CONFIG_SPL_ENV_SUPPORT
 731         env_init();
 732         env_relocate_spec();
 733         if (getenv_yesno("boot_os") != 1)
 734                 return 1;
 735 #endif
 736
 737         return 0;
 738 }
 739 #endif
 740
 741 #ifdef CONFIG_USB_DWC3
 742 static struct dwc3_device usb_otg_ss2 = {
 743         .maximum_speed = USB_SPEED_HIGH,
 744         .base = DRA7_USB_OTG_SS2_BASE,
 745         .tx_fifo_resize = false,
 746         .index = 1,
 747 };
 748
 749 static struct dwc3_omap_device usb_otg_ss2_glue = {
 750         .base = (void *)DRA7_USB_OTG_SS2_GLUE_BASE,
 751         .utmi_mode = DWC3_OMAP_UTMI_MODE_SW,
 752         .index = 1,
 753 };
 754
 755 static struct ti_usb_phy_device usb_phy2_device = {
 756         .usb2_phy_power = (void *)DRA7_USB2_PHY2_POWER,
 757         .index = 1,
 758 };
 759
 760 int usb_gadget_handle_interrupts(int index)
 761 {
 762         u32 status;
 763
 764         status = dwc3_omap_uboot_interrupt_status(index);
 765         if (status)
 766                 dwc3_uboot_handle_interrupt(index);
 767
 768         return 0;
 769 }
 770 #endif /* CONFIG_USB_DWC3 */
 771
 772 #if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP)
 773 int omap_xhci_board_usb_init(int index, enum usb_init_type init)
 774 {
 775         enable_usb_clocks(index);
 776         switch (index) {
 777         case 0:
 778                 if (init == USB_INIT_DEVICE) {
 779                         printf("port %d can't be used as device\n", index);
 780                         disable_usb_clocks(index);
 781                         return -EINVAL;
 782                 }
 783                 break;
 784         case 1:
 785                 if (init == USB_INIT_DEVICE) {
 786 #ifdef CONFIG_USB_DWC3
 787                         usb_otg_ss2.dr_mode = USB_DR_MODE_PERIPHERAL;
 788                         usb_otg_ss2_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID;
 789                         ti_usb_phy_uboot_init(&usb_phy2_device);
 790                         dwc3_omap_uboot_init(&usb_otg_ss2_glue);
 791                         dwc3_uboot_init(&usb_otg_ss2);
 792 #endif
 793                 } else {
 794                         printf("port %d can't be used as host\n", index);
 795                         disable_usb_clocks(index);
 796                         return -EINVAL;
 797                 }
 798
 799                 break;
 800         default:
 801                 printf("Invalid Controller Index\n");
 802         }
 803
 804         return 0;
 805 }
 806
 807 int omap_xhci_board_usb_cleanup(int index, enum usb_init_type init)
 808 {
 809 #ifdef CONFIG_USB_DWC3
 810         switch (index) {
 811         case 0:
 812         case 1:
 813                 if (init == USB_INIT_DEVICE) {
 814                         ti_usb_phy_uboot_exit(index);
 815                         dwc3_uboot_exit(index);
 816                         dwc3_omap_uboot_exit(index);
 817                 }
 818                 break;
 819         default:
 820                 printf("Invalid Controller Index\n");
 821         }
 822 #endif
 823         disable_usb_clocks(index);
 824         return 0;
 825 }
 826 #endif /* defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP) */
 827
 828 #ifdef CONFIG_DRIVER_TI_CPSW
 829
 830 /* Delay value to add to calibrated value */
 831 #define RGMII0_TXCTL_DLY_VAL            ((0x3 << 5) + 0x8)
 832 #define RGMII0_TXD0_DLY_VAL             ((0x3 << 5) + 0x8)
 833 #define RGMII0_TXD1_DLY_VAL             ((0x3 << 5) + 0x2)
 834 #define RGMII0_TXD2_DLY_VAL             ((0x4 << 5) + 0x0)
 835 #define RGMII0_TXD3_DLY_VAL             ((0x4 << 5) + 0x0)
 836 #define VIN2A_D13_DLY_VAL               ((0x3 << 5) + 0x8)
 837 #define VIN2A_D17_DLY_VAL               ((0x3 << 5) + 0x8)
 838 #define VIN2A_D16_DLY_VAL               ((0x3 << 5) + 0x2)
 839 #define VIN2A_D15_DLY_VAL               ((0x4 << 5) + 0x0)
 840 #define VIN2A_D14_DLY_VAL               ((0x4 << 5) + 0x0)
 841
 842 static void cpsw_control(int enabled)
 843 {
 844         /* VTP can be added here */
 845 }
 846
 847 static struct cpsw_slave_data cpsw_slaves[] = {
 848         {
 849                 .slave_reg_ofs  = 0x208,
 850                 .sliver_reg_ofs = 0xd80,
 851                 .phy_addr       = 1,
 852         },
 853         {
 854                 .slave_reg_ofs  = 0x308,
 855                 .sliver_reg_ofs = 0xdc0,
 856                 .phy_addr       = 2,
 857         },
 858 };
 859
 860 static struct cpsw_platform_data cpsw_data = {
 861         .mdio_base              = CPSW_MDIO_BASE,
 862         .cpsw_base              = CPSW_BASE,
 863         .mdio_div               = 0xff,
 864         .channels               = 8,
 865         .cpdma_reg_ofs          = 0x800,
 866         .slaves                 = 1,
 867         .slave_data             = cpsw_slaves,
 868         .ale_reg_ofs            = 0xd00,
 869         .ale_entries            = 1024,
 870         .host_port_reg_ofs      = 0x108,
 871         .hw_stats_reg_ofs       = 0x900,
 872         .bd_ram_ofs             = 0x2000,
 873         .mac_control            = (1 << 5),
 874         .control                = cpsw_control,
 875         .host_port_num          = 0,
 876         .version                = CPSW_CTRL_VERSION_2,
 877 };
 878
 879 static u64 mac_to_u64(u8 mac[6])
 880 {
 881         int i;
 882         u64 addr = 0;
 883
 884         for (i = 0; i < 6; i++) {
 885                 addr <<= 8;
 886                 addr |= mac[i];
 887         }
 888
 889         return addr;
 890 }
 891
 892 static void u64_to_mac(u64 addr, u8 mac[6])
 893 {
 894         mac[5] = addr;
 895         mac[4] = addr >> 8;
 896         mac[3] = addr >> 16;
 897         mac[2] = addr >> 24;
 898         mac[1] = addr >> 32;
 899         mac[0] = addr >> 40;
 900 }
 901
 902 int board_eth_init(bd_t *bis)
 903 {
 904         int ret;
 905         uint8_t mac_addr[6];
 906         uint32_t mac_hi, mac_lo;
 907         uint32_t ctrl_val;
 908         int i;
 909         u64 mac1, mac2;
 910         u8 mac_addr1[6], mac_addr2[6];
 911         int num_macs;
 912
 913         /* try reading mac address from efuse */
 914         mac_lo = readl((*ctrl)->control_core_mac_id_0_lo);
 915         mac_hi = readl((*ctrl)->control_core_mac_id_0_hi);
 916         mac_addr[0] = (mac_hi & 0xFF0000) >> 16;
 917         mac_addr[1] = (mac_hi & 0xFF00) >> 8;
 918         mac_addr[2] = mac_hi & 0xFF;
 919         mac_addr[3] = (mac_lo & 0xFF0000) >> 16;
 920         mac_addr[4] = (mac_lo & 0xFF00) >> 8;
 921         mac_addr[5] = mac_lo & 0xFF;
 922
 923         if (!getenv("ethaddr")) {
 924                 printf("<ethaddr> not set. Validating first E-fuse MAC\n");
 925
 926                 if (is_valid_ethaddr(mac_addr))
 927                         eth_setenv_enetaddr("ethaddr", mac_addr);
 928         }
 929
 930         mac_lo = readl((*ctrl)->control_core_mac_id_1_lo);
 931         mac_hi = readl((*ctrl)->control_core_mac_id_1_hi);
 932         mac_addr[0] = (mac_hi & 0xFF0000) >> 16;
 933         mac_addr[1] = (mac_hi & 0xFF00) >> 8;
 934         mac_addr[2] = mac_hi & 0xFF;
 935         mac_addr[3] = (mac_lo & 0xFF0000) >> 16;
 936         mac_addr[4] = (mac_lo & 0xFF00) >> 8;
 937         mac_addr[5] = mac_lo & 0xFF;
 938
 939         if (!getenv("eth1addr")) {
 940                 if (is_valid_ethaddr(mac_addr))
 941                         eth_setenv_enetaddr("eth1addr", mac_addr);
 942         }
 943
 944         ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33);
 945         ctrl_val |= 0x22;
 946         writel(ctrl_val, (*ctrl)->control_core_control_io1);
 947
 948         /* The phy address for the AM57xx IDK are different than x15 */
 949         if (board_is_am572x_idk() || board_is_am571x_idk()) {
 950                 cpsw_data.slave_data[0].phy_addr = 0;
 951                 cpsw_data.slave_data[1].phy_addr = 1;
 952         }
 953
 954         ret = cpsw_register(&cpsw_data);
 955         if (ret < 0)
 956                 printf("Error %d registering CPSW switch\n", ret);
 957
 958         /*
 959          * Export any Ethernet MAC addresses from EEPROM.
 960          * On AM57xx the 2 MAC addresses define the address range
 961          */
 962         board_ti_get_eth_mac_addr(0, mac_addr1);
 963         board_ti_get_eth_mac_addr(1, mac_addr2);
 964
 965         if (is_valid_ethaddr(mac_addr1) && is_valid_ethaddr(mac_addr2)) {
 966                 mac1 = mac_to_u64(mac_addr1);
 967                 mac2 = mac_to_u64(mac_addr2);
 968
 969                 /* must contain an address range */
 970                 num_macs = mac2 - mac1 + 1;
 971                 /* <= 50 to protect against user programming error */
 972                 if (num_macs > 0 && num_macs <= 50) {
 973                         for (i = 0; i < num_macs; i++) {
 974                                 u64_to_mac(mac1 + i, mac_addr);
 975                                 if (is_valid_ethaddr(mac_addr)) {
 976                                         eth_setenv_enetaddr_by_index("eth",
 977                                                                      i + 2,
 978                                                                      mac_addr);
 979                                 }
 980                         }
 981                 }
 982         }
 983
 984         return ret;
 985 }
 986 #endif
 987
 988 #ifdef CONFIG_BOARD_EARLY_INIT_F
 989 /* VTT regulator enable */
 990 static inline void vtt_regulator_enable(void)
 991 {
 992         if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL)
 993                 return;
 994
 995         gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
 996         gpio_direction_output(GPIO_DDR_VTT_EN, 1);
 997 }
 998
 999 int board_early_init_f(void)
1000 {
1001         vtt_regulator_enable();
1002         return 0;
1003 }
1004 #endif
1005
1006 #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
1007 int ft_board_setup(void *blob, bd_t *bd)
1008 {
1009         ft_cpu_setup(blob, bd);
1010
1011         return 0;
1012 }
1013 #endif
1014
1015 #ifdef CONFIG_SPL_LOAD_FIT
1016 int board_fit_config_name_match(const char *name)
1017 {
1018         if (board_is_x15()) {
1019                 if (board_is_x15_revb1()) {
1020                         if (!strcmp(name, "am57xx-beagle-x15-revb1"))
1021                                 return 0;
1022                 } else if (!strcmp(name, "am57xx-beagle-x15")) {
1023                         return 0;
1024                 }
1025         } else if (board_is_am572x_evm() &&
1026                    !strcmp(name, "am57xx-beagle-x15")) {
1027                 return 0;
1028         } else if (board_is_am572x_idk() && !strcmp(name, "am572x-idk")) {
1029                 return 0;
1030         } else if (board_is_am571x_idk() && !strcmp(name, "am571x-idk")) {
1031                 return 0;
1032         }
1033
1034         return -1;
1035 }
1036 #endif
1037
1038 #ifdef CONFIG_TI_SECURE_DEVICE
1039 void board_fit_image_post_process(void **p_image, size_t *p_size)
1040 {
1041         secure_boot_verify_image(p_image, p_size);
1042 }
1043
1044 void board_tee_image_process(ulong tee_image, size_t tee_size)
1045 {
1046         secure_tee_install((u32)tee_image);
1047 }
1048
1049 U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_TEE, board_tee_image_process);
1050 #endif