board/ge/bx50v3/bx50v3.c

   1 /*
   2  * Copyright 2015 Timesys Corporation
   3  * Copyright 2015 General Electric Company
   4  * Copyright 2012 Freescale Semiconductor, Inc.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #include <asm/arch/clock.h>
  10 #include <asm/arch/imx-regs.h>
  11 #include <asm/arch/iomux.h>
  12 #include <asm/arch/mx6-pins.h>
  13 #include <linux/errno.h>
  14 #include <asm/gpio.h>
  15 #include <asm/imx-common/mxc_i2c.h>
  16 #include <asm/imx-common/iomux-v3.h>
  17 #include <asm/imx-common/boot_mode.h>
  18 #include <asm/imx-common/video.h>
  19 #include <mmc.h>
  20 #include <fsl_esdhc.h>
  21 #include <miiphy.h>
  22 #include <netdev.h>
  23 #include <asm/arch/mxc_hdmi.h>
  24 #include <asm/arch/crm_regs.h>
  25 #include <asm/io.h>
  26 #include <asm/arch/sys_proto.h>
  27 #include <i2c.h>
  28 #include <pwm.h>
  29 DECLARE_GLOBAL_DATA_PTR;
  30
  31 #define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP |      \
  32         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
  33         PAD_CTL_HYS)
  34
  35 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  36         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |                 \
  37         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  38
  39 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |                    \
  40         PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |                 \
  41         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  42
  43 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
  44         PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
  45
  46 #define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
  47         PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
  48
  49 #define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
  50         PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
  51
  52 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
  53                       PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
  54
  55 #define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                    \
  56         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |   \
  57         PAD_CTL_ODE | PAD_CTL_SRE_FAST)
  58
  59 #define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
  60
  61 int dram_init(void)
  62 {
  63         gd->ram_size = imx_ddr_size();
  64
  65         return 0;
  66 }
  67
  68 static iomux_v3_cfg_t const uart3_pads[] = {
  69         MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
  70         MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
  71         MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  72         MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  73 };
  74
  75 static iomux_v3_cfg_t const uart4_pads[] = {
  76         MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  77         MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  78 };
  79
  80 static iomux_v3_cfg_t const enet_pads[] = {
  81         MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
  82         MX6_PAD_ENET_MDC__ENET_MDC   | MUX_PAD_CTRL(ENET_PAD_CTRL),
  83         MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
  84         MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
  85         MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
  86         MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
  87         MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
  88         MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
  89         MX6_PAD_ENET_REF_CLK__ENET_TX_CLK  | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
  90         MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  91         MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  92         MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  93         MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  94         MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  95         MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
  96         /* AR8033 PHY Reset */
  97         MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
  98 };
  99
 100 static void setup_iomux_enet(void)
 101 {
 102         imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
 103
 104         /* Reset AR8033 PHY */
 105         gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
 106         mdelay(10);
 107         gpio_set_value(IMX_GPIO_NR(1, 28), 1);
 108         mdelay(1);
 109 }
 110
 111 static iomux_v3_cfg_t const usdhc2_pads[] = {
 112         MX6_PAD_SD2_CLK__SD2_CLK        | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 113         MX6_PAD_SD2_CMD__SD2_CMD        | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 114         MX6_PAD_SD2_DAT0__SD2_DATA0     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 115         MX6_PAD_SD2_DAT1__SD2_DATA1     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 116         MX6_PAD_SD2_DAT2__SD2_DATA2     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 117         MX6_PAD_SD2_DAT3__SD2_DATA3     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 118         MX6_PAD_GPIO_4__GPIO1_IO04      | MUX_PAD_CTRL(NO_PAD_CTRL),
 119 };
 120
 121 static iomux_v3_cfg_t const usdhc3_pads[] = {
 122         MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 123         MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 124         MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 125         MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 126         MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 127         MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 128         MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 129         MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 130         MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 131         MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 132         MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 133 };
 134
 135 static iomux_v3_cfg_t const usdhc4_pads[] = {
 136         MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 137         MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 138         MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 139         MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 140         MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 141         MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 142         MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 143         MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 144         MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 145         MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 146         MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
 147         MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
 148 };
 149
 150 static iomux_v3_cfg_t const ecspi1_pads[] = {
 151         MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
 152         MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
 153         MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
 154         MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
 155 };
 156
 157 static struct i2c_pads_info i2c_pad_info1 = {
 158         .scl = {
 159                 .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
 160                 .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
 161                 .gp = IMX_GPIO_NR(5, 27)
 162         },
 163         .sda = {
 164                 .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
 165                 .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
 166                 .gp = IMX_GPIO_NR(5, 26)
 167         }
 168 };
 169
 170 static struct i2c_pads_info i2c_pad_info2 = {
 171         .scl = {
 172                 .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
 173                 .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
 174                 .gp = IMX_GPIO_NR(4, 12)
 175         },
 176         .sda = {
 177                 .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
 178                 .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
 179                 .gp = IMX_GPIO_NR(4, 13)
 180         }
 181 };
 182
 183 static struct i2c_pads_info i2c_pad_info3 = {
 184         .scl = {
 185                 .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
 186                 .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
 187                 .gp = IMX_GPIO_NR(1, 3)
 188         },
 189         .sda = {
 190                 .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
 191                 .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
 192                 .gp = IMX_GPIO_NR(1, 6)
 193         }
 194 };
 195
 196 #ifdef CONFIG_MXC_SPI
 197 int board_spi_cs_gpio(unsigned bus, unsigned cs)
 198 {
 199         return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1;
 200 }
 201
 202 static void setup_spi(void)
 203 {
 204         imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
 205 }
 206 #endif
 207
 208 static iomux_v3_cfg_t const pcie_pads[] = {
 209         MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
 210         MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
 211 };
 212
 213 static void setup_pcie(void)
 214 {
 215         imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
 216 }
 217
 218 static void setup_iomux_uart(void)
 219 {
 220         imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
 221         imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
 222 }
 223
 224 #ifdef CONFIG_FSL_ESDHC
 225 struct fsl_esdhc_cfg usdhc_cfg[3] = {
 226         {USDHC2_BASE_ADDR},
 227         {USDHC3_BASE_ADDR},
 228         {USDHC4_BASE_ADDR},
 229 };
 230
 231 #define USDHC2_CD_GPIO  IMX_GPIO_NR(1, 4)
 232 #define USDHC4_CD_GPIO  IMX_GPIO_NR(6, 11)
 233
 234 int board_mmc_getcd(struct mmc *mmc)
 235 {
 236         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 237         int ret = 0;
 238
 239         switch (cfg->esdhc_base) {
 240         case USDHC2_BASE_ADDR:
 241                 ret = !gpio_get_value(USDHC2_CD_GPIO);
 242                 break;
 243         case USDHC3_BASE_ADDR:
 244                 ret = 1; /* eMMC is always present */
 245                 break;
 246         case USDHC4_BASE_ADDR:
 247                 ret = !gpio_get_value(USDHC4_CD_GPIO);
 248                 break;
 249         }
 250
 251         return ret;
 252 }
 253
 254 int board_mmc_init(bd_t *bis)
 255 {
 256         int ret;
 257         int i;
 258
 259         for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
 260                 switch (i) {
 261                 case 0:
 262                         imx_iomux_v3_setup_multiple_pads(
 263                                 usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
 264                         gpio_direction_input(USDHC2_CD_GPIO);
 265                         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 266                         break;
 267                 case 1:
 268                         imx_iomux_v3_setup_multiple_pads(
 269                                 usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
 270                         usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 271                         break;
 272                 case 2:
 273                         imx_iomux_v3_setup_multiple_pads(
 274                                 usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
 275                         gpio_direction_input(USDHC4_CD_GPIO);
 276                         usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 277                         break;
 278                 default:
 279                         printf("Warning: you configured more USDHC controllers\n"
 280                                "(%d) then supported by the board (%d)\n",
 281                                i + 1, CONFIG_SYS_FSL_USDHC_NUM);
 282                         return -EINVAL;
 283                 }
 284
 285                 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
 286                 if (ret)
 287                         return ret;
 288         }
 289
 290         return 0;
 291 }
 292 #endif
 293
 294 static int mx6_rgmii_rework(struct phy_device *phydev)
 295 {
 296         /* Configure AR8033 to ouput a 125MHz clk from CLK_25M */
 297         /* set device address 0x7 */
 298         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
 299         /* offset 0x8016: CLK_25M Clock Select */
 300         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
 301         /* enable register write, no post increment, address 0x7 */
 302         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
 303         /* set to 125 MHz from local PLL source */
 304         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18);
 305
 306         /* rgmii tx clock delay enable */
 307         /* set debug port address: SerDes Test and System Mode Control */
 308         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
 309         /* enable rgmii tx clock delay */
 310         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
 311
 312         return 0;
 313 }
 314
 315 int board_phy_config(struct phy_device *phydev)
 316 {
 317         mx6_rgmii_rework(phydev);
 318
 319         if (phydev->drv->config)
 320                 phydev->drv->config(phydev);
 321
 322         return 0;
 323 }
 324
 325 #if defined(CONFIG_VIDEO_IPUV3)
 326 static iomux_v3_cfg_t const backlight_pads[] = {
 327         /* Power for LVDS Display */
 328         MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
 329 #define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
 330         /* Backlight enable for LVDS display */
 331         MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
 332 #define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
 333         /* backlight PWM brightness control */
 334         MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
 335 };
 336
 337 static void do_enable_hdmi(struct display_info_t const *dev)
 338 {
 339         imx_enable_hdmi_phy();
 340 }
 341
 342 int board_cfb_skip(void)
 343 {
 344         gpio_direction_output(LVDS_POWER_GP, 1);
 345
 346         return 0;
 347 }
 348
 349 static int detect_baseboard(struct display_info_t const *dev)
 350 {
 351         if (IS_ENABLED(CONFIG_TARGET_GE_B450V3) ||
 352             IS_ENABLED(CONFIG_TARGET_GE_B650V3))
 353                 return 1;
 354
 355         return 0;
 356 }
 357
 358 struct display_info_t const displays[] = {{
 359         .bus    = -1,
 360         .addr   = -1,
 361         .pixfmt = IPU_PIX_FMT_RGB24,
 362         .detect = detect_baseboard,
 363         .enable = NULL,
 364         .mode   = {
 365                 .name           = "G121X1-L03",
 366                 .refresh        = 60,
 367                 .xres           = 1024,
 368                 .yres           = 768,
 369                 .pixclock       = 15385,
 370                 .left_margin    = 20,
 371                 .right_margin   = 300,
 372                 .upper_margin   = 30,
 373                 .lower_margin   = 8,
 374                 .hsync_len      = 1,
 375                 .vsync_len      = 1,
 376                 .sync           = FB_SYNC_EXT,
 377                 .vmode          = FB_VMODE_NONINTERLACED
 378 } }, {
 379         .bus    = -1,
 380         .addr   = 3,
 381         .pixfmt = IPU_PIX_FMT_RGB24,
 382         .detect = detect_hdmi,
 383         .enable = do_enable_hdmi,
 384         .mode   = {
 385                 .name           = "HDMI",
 386                 .refresh        = 60,
 387                 .xres           = 1024,
 388                 .yres           = 768,
 389                 .pixclock       = 15385,
 390                 .left_margin    = 220,
 391                 .right_margin   = 40,
 392                 .upper_margin   = 21,
 393                 .lower_margin   = 7,
 394                 .hsync_len      = 60,
 395                 .vsync_len      = 10,
 396                 .sync           = FB_SYNC_EXT,
 397                 .vmode          = FB_VMODE_NONINTERLACED
 398 } } };
 399 size_t display_count = ARRAY_SIZE(displays);
 400
 401 static void enable_videopll(void)
 402 {
 403         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 404         s32 timeout = 100000;
 405
 406         setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
 407
 408         /* set video pll to 910MHz (24MHz * (37+11/12))
 409         * video pll post div to 910/4 = 227.5MHz
 410         */
 411         clrsetbits_le32(&ccm->analog_pll_video,
 412                         BM_ANADIG_PLL_VIDEO_DIV_SELECT |
 413                         BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT,
 414                         BF_ANADIG_PLL_VIDEO_DIV_SELECT(37) |
 415                         BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0));
 416
 417         writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
 418         writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
 419
 420         clrbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
 421
 422         while (timeout--)
 423                 if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
 424                         break;
 425
 426         if (timeout < 0)
 427                 printf("Warning: video pll lock timeout!\n");
 428
 429         clrsetbits_le32(&ccm->analog_pll_video,
 430                         BM_ANADIG_PLL_VIDEO_BYPASS,
 431                         BM_ANADIG_PLL_VIDEO_ENABLE);
 432 }
 433
 434 static void setup_display_b850v3(void)
 435 {
 436         struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 437         struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
 438
 439         enable_videopll();
 440
 441         /* IPU1 D0 clock is 227.5 / 3.5 = 65MHz */
 442         clrbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
 443
 444         imx_setup_hdmi();
 445
 446         /* Set LDB_DI0 as clock source for IPU_DI0 */
 447         clrsetbits_le32(&mxc_ccm->chsccdr,
 448                         MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
 449                         (CHSCCDR_CLK_SEL_LDB_DI0 <<
 450                          MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
 451
 452         /* Turn on IPU LDB DI0 clocks */
 453         setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
 454
 455         enable_ipu_clock();
 456
 457         writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
 458                IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW |
 459                IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
 460                IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
 461                IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT |
 462                IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
 463                IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
 464                IOMUXC_GPR2_SPLIT_MODE_EN_MASK |
 465                IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 |
 466                IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0,
 467                &iomux->gpr[2]);
 468
 469         clrbits_le32(&iomux->gpr[3],
 470                      IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
 471                      IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
 472                      IOMUXC_GPR3_HDMI_MUX_CTL_MASK);
 473 }
 474
 475 static void setup_display_bx50v3(void)
 476 {
 477         struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 478         struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
 479
 480         /* When a reset/reboot is performed the display power needs to be turned
 481          * off for atleast 500ms. The boot time is ~300ms, we need to wait for
 482          * an additional 200ms here. Unfortunately we use external PMIC for
 483          * doing the reset, so can not differentiate between POR vs soft reset
 484          */
 485         mdelay(200);
 486
 487         /* IPU1 DI0 clock is 480/7 = 68.5 MHz */
 488         setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
 489
 490         /* Set LDB_DI0 as clock source for IPU_DI0 */
 491         clrsetbits_le32(&mxc_ccm->chsccdr,
 492                         MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
 493                         (CHSCCDR_CLK_SEL_LDB_DI0 <<
 494                         MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
 495
 496         /* Turn on IPU LDB DI0 clocks */
 497         setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
 498
 499         enable_ipu_clock();
 500
 501         writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
 502                IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
 503                IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
 504                IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
 505                IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
 506                &iomux->gpr[2]);
 507
 508         clrsetbits_le32(&iomux->gpr[3],
 509                         IOMUXC_GPR3_LVDS0_MUX_CTL_MASK,
 510                        (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
 511                         IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET));
 512
 513         /* backlights off until needed */
 514         imx_iomux_v3_setup_multiple_pads(backlight_pads,
 515                                          ARRAY_SIZE(backlight_pads));
 516         gpio_direction_input(LVDS_POWER_GP);
 517         gpio_direction_input(LVDS_BACKLIGHT_GP);
 518 }
 519 #endif /* CONFIG_VIDEO_IPUV3 */
 520
 521 /*
 522  * Do not overwrite the console
 523  * Use always serial for U-Boot console
 524  */
 525 int overwrite_console(void)
 526 {
 527         return 1;
 528 }
 529
 530 int board_eth_init(bd_t *bis)
 531 {
 532         setup_iomux_enet();
 533         setup_pcie();
 534
 535         return cpu_eth_init(bis);
 536 }
 537
 538 static iomux_v3_cfg_t const misc_pads[] = {
 539         MX6_PAD_KEY_ROW2__GPIO4_IO11    | MUX_PAD_CTRL(NO_PAD_CTRL),
 540         MX6_PAD_EIM_A25__GPIO5_IO02     | MUX_PAD_CTRL(NC_PAD_CTRL),
 541         MX6_PAD_EIM_CS0__GPIO2_IO23     | MUX_PAD_CTRL(NC_PAD_CTRL),
 542         MX6_PAD_EIM_CS1__GPIO2_IO24     | MUX_PAD_CTRL(NC_PAD_CTRL),
 543         MX6_PAD_EIM_OE__GPIO2_IO25      | MUX_PAD_CTRL(NC_PAD_CTRL),
 544         MX6_PAD_EIM_BCLK__GPIO6_IO31    | MUX_PAD_CTRL(NC_PAD_CTRL),
 545         MX6_PAD_GPIO_1__GPIO1_IO01      | MUX_PAD_CTRL(NC_PAD_CTRL),
 546 };
 547 #define SUS_S3_OUT      IMX_GPIO_NR(4, 11)
 548 #define WIFI_EN IMX_GPIO_NR(6, 14)
 549
 550 int board_early_init_f(void)
 551 {
 552         imx_iomux_v3_setup_multiple_pads(misc_pads,
 553                                          ARRAY_SIZE(misc_pads));
 554
 555         setup_iomux_uart();
 556
 557 #if defined(CONFIG_VIDEO_IPUV3)
 558         if (IS_ENABLED(CONFIG_TARGET_GE_B850V3))
 559                 /* Set LDB clock to Video PLL */
 560                 select_ldb_di_clock_source(MXC_PLL5_CLK);
 561         else
 562                 /* Set LDB clock to USB PLL */
 563                 select_ldb_di_clock_source(MXC_PLL3_SW_CLK);
 564 #endif
 565         return 0;
 566 }
 567
 568 int board_init(void)
 569 {
 570         gpio_direction_output(SUS_S3_OUT, 1);
 571         gpio_direction_output(WIFI_EN, 1);
 572 #if defined(CONFIG_VIDEO_IPUV3)
 573         if (IS_ENABLED(CONFIG_TARGET_GE_B850V3))
 574                 setup_display_b850v3();
 575         else
 576                 setup_display_bx50v3();
 577 #endif
 578         /* address of boot parameters */
 579         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 580
 581 #ifdef CONFIG_MXC_SPI
 582         setup_spi();
 583 #endif
 584         setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
 585         setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
 586         setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
 587
 588         return 0;
 589 }
 590
 591 #ifdef CONFIG_CMD_BMODE
 592 static const struct boot_mode board_boot_modes[] = {
 593         /* 4 bit bus width */
 594         {"sd2",  MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
 595         {"sd3",  MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
 596         {NULL,   0},
 597 };
 598 #endif
 599
 600 void pmic_init(void)
 601 {
 602 #define I2C_PMIC                0x2
 603 #define DA9063_I2C_ADDR         0x58
 604 #define DA9063_REG_BCORE2_CFG   0x9D
 605 #define DA9063_REG_BCORE1_CFG   0x9E
 606 #define DA9063_REG_BPRO_CFG     0x9F
 607 #define DA9063_REG_BIO_CFG      0xA0
 608 #define DA9063_REG_BMEM_CFG     0xA1
 609 #define DA9063_REG_BPERI_CFG    0xA2
 610 #define DA9063_BUCK_MODE_MASK   0xC0
 611 #define DA9063_BUCK_MODE_MANUAL 0x00
 612 #define DA9063_BUCK_MODE_SLEEP  0x40
 613 #define DA9063_BUCK_MODE_SYNC   0x80
 614 #define DA9063_BUCK_MODE_AUTO   0xC0
 615
 616         uchar val;
 617
 618         i2c_set_bus_num(I2C_PMIC);
 619
 620         i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1);
 621         val &= ~DA9063_BUCK_MODE_MASK;
 622         val |= DA9063_BUCK_MODE_SYNC;
 623         i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1);
 624
 625         i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1);
 626         val &= ~DA9063_BUCK_MODE_MASK;
 627         val |= DA9063_BUCK_MODE_SYNC;
 628         i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1);
 629
 630         i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1);
 631         val &= ~DA9063_BUCK_MODE_MASK;
 632         val |= DA9063_BUCK_MODE_SYNC;
 633         i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1);
 634
 635         i2c_read(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1);
 636         val &= ~DA9063_BUCK_MODE_MASK;
 637         val |= DA9063_BUCK_MODE_SYNC;
 638         i2c_write(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1);
 639
 640         i2c_read(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1);
 641         val &= ~DA9063_BUCK_MODE_MASK;
 642         val |= DA9063_BUCK_MODE_SYNC;
 643         i2c_write(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1);
 644
 645         i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1);
 646         val &= ~DA9063_BUCK_MODE_MASK;
 647         val |= DA9063_BUCK_MODE_SYNC;
 648         i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1);
 649 }
 650
 651 int board_late_init(void)
 652 {
 653 #ifdef CONFIG_CMD_BMODE
 654         add_board_boot_modes(board_boot_modes);
 655 #endif
 656
 657 #ifdef CONFIG_VIDEO_IPUV3
 658         /* We need at least 200ms between power on and backlight on
 659          * as per specifications from CHI MEI */
 660         mdelay(250);
 661
 662         /* enable backlight PWM 1 */
 663         pwm_init(0, 0, 0);
 664
 665         /* duty cycle 5000000ns, period: 5000000ns */
 666         pwm_config(0, 5000000, 5000000);
 667
 668         /* Backlight Power */
 669         gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
 670
 671         pwm_enable(0);
 672 #endif
 673
 674         /* board specific pmic init */
 675         pmic_init();
 676
 677         return 0;
 678 }
 679
 680 int checkboard(void)
 681 {
 682         printf("BOARD: %s\n", CONFIG_BOARD_NAME);
 683         return 0;
 684 }