board/freescale/t208xrdb/ddr.c

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0
   5  */
   6
   7 #include <common.h>
   8 #include <i2c.h>
   9 #include <hwconfig.h>
  10 #include <asm/mmu.h>
  11 #include <fsl_ddr_sdram.h>
  12 #include <fsl_ddr_dimm_params.h>
  13 #include <asm/fsl_law.h>
  14 #include "ddr.h"
  15
  16 DECLARE_GLOBAL_DATA_PTR;
  17
  18 void fsl_ddr_board_options(memctl_options_t *popts,
  19                                 dimm_params_t *pdimm,
  20                                 unsigned int ctrl_num)
  21 {
  22         const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
  23         ulong ddr_freq;
  24
  25         if (ctrl_num > 1) {
  26                 printf("Not supported controller number %d\n", ctrl_num);
  27                 return;
  28         }
  29         if (!pdimm->n_ranks)
  30                 return;
  31
  32         pbsp = udimms[0];
  33
  34         /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
  35          * freqency and n_banks specified in board_specific_parameters table.
  36          */
  37         ddr_freq = get_ddr_freq(0) / 1000000;
  38         while (pbsp->datarate_mhz_high) {
  39                 if (pbsp->n_ranks == pdimm->n_ranks &&
  40                     (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
  41                         if (ddr_freq <= pbsp->datarate_mhz_high) {
  42                                 popts->clk_adjust = pbsp->clk_adjust;
  43                                 popts->wrlvl_start = pbsp->wrlvl_start;
  44                                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  45                                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  46                                 goto found;
  47                         }
  48                         pbsp_highest = pbsp;
  49                 }
  50                 pbsp++;
  51         }
  52
  53         if (pbsp_highest) {
  54                 printf("Error: board specific timing not found");
  55                 printf("for data rate %lu MT/s\n", ddr_freq);
  56                 printf("Trying to use the highest speed (%u) parameters\n",
  57                        pbsp_highest->datarate_mhz_high);
  58                 popts->clk_adjust = pbsp_highest->clk_adjust;
  59                 popts->wrlvl_start = pbsp_highest->wrlvl_start;
  60                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  61                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  62         } else {
  63                 panic("DIMM is not supported by this board");
  64         }
  65 found:
  66         debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
  67                 "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
  68                 "wrlvl_ctrl_3 0x%x\n",
  69                 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
  70                 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
  71                 pbsp->wrlvl_ctl_3);
  72
  73         /*
  74          * Factors to consider for half-strength driver enable:
  75          *      - number of DIMMs installed
  76          */
  77         popts->half_strength_driver_enable = 0;
  78         /*
  79          * Write leveling override
  80          */
  81         popts->wrlvl_override = 1;
  82         popts->wrlvl_sample = 0xf;
  83
  84         /*
  85          * Rtt and Rtt_WR override
  86          */
  87         popts->rtt_override = 0;
  88
  89         /* Enable ZQ calibration */
  90         popts->zq_en = 1;
  91
  92         /* DHC_EN =1, ODT = 75 Ohm */
  93         popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
  94         popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
  95 }
  96
  97 phys_size_t initdram(int board_type)
  98 {
  99         phys_size_t dram_size;
 100
 101 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
 102         puts("Initializing....using SPD\n");
 103         dram_size = fsl_ddr_sdram();
 104 #else
 105         /* DDR has been initialised by first stage boot loader */
 106         dram_size = fsl_ddr_sdram_size();
 107 #endif
 108         dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 109         dram_size *= 0x100000;
 110
 111         return dram_size;
 112 }